Owner`s Manual - Innovative Marine

Owner`s Manual - Innovative Marine
Owner’s Manual
1
CONTENTS
TABLE OF CONTENTS
Important Safety Instructions
3-4
Parts—Exploded View & Identification
SingleStrip 12
SingleStrip 18
SingleStrip 24
SingleStrip 36
SingleStrip 48
5
6
7
8
9
Introduction
Specifications 12”, 18”, 24”
Specifications 36”, 48”
Features
10
11
12
13
Getting Started
Choosing a Location
SingleStrip on Framed Tank
SingleStrip on Rimless Tank
Single Strip inside Canopy
Powering Up Utility
14
15
16
17
18
Notes
20-21
Warranty Information
22-23
2
To guard against injury, basic safety precautions should be observed
including the following:
READ ALL SAFETY INSTRUCTIONS BEFORE USE.
WARNING
To avoid electric shock, special care should be taken since water is
employed in the use of aquarium equipment. For each of the following situations, do not attempt to repair yourself. Return the appliance
to an authorized service facility for service or discard the appliance.







If the appliance falls into water, DO NOT reach for it! First unplug
it an then retrieve it. If the electrical components of the appliance
get wet, unplug the appliance immediately.
Carefully examine the appliance after installation. It should not
be plugged in if there is water on parts not intended to be wet.
Do not operate any appliance if it has a damaged cord or plug, or
if it is malfunctioning or if it is dropped or damaged in any manner.
To avoid the possibility of the appliance plug or receptacle getting
wet, position aquarium to one side
of a wall mounted receptacle to
prevent water from dripping onto
the receptacle plug. A “Drip Loop”
should be arranged by the user for
EACH cord connecting an aquarium appliance to a receptacle. The
“Drip Loop” is that part of the cord
below the level of the receptacle or
the connector if an extension cord
Drip Loop
is used. This “Drip Loop” prevents
water travelling along the cord and
coming in contact with the receptacle. If the plug or the receptacle do get wet DO NOT unplug the cord. Disconnect the fuse to
the circuit breaker that supplies power to the appliance. Then
unplug and examine for the presence of water in the receptacle.
Close supervision is necessary when any appliance is used by or
near children.
To avoid injury, do not contact moving parts or hot parts such as
heaters, reflectors, lamps bulbs and etc.
Always unplug an appliance from the outlet when not in use, before putting on or taking off parts, and before cleaning. Never
yank the cord to pull plug from outlet. Grasp the plug and pull to
disconnect.
3
IMPORTANT SAFETY
INSTRUCTIONS
WARNING
IMPORTANT SAFETY
INSTRUCTIONS

Do not use an appliance for other than intended use. The use
of attachments not recommended or sold by the appliance
manufacturer may case an unsafe condition.
Do not install or store the appliance where it will be exposed to
the weather or to temperatures below freezing.
Make sure an appliance mounted on a tank is securely installed
before operating it.
Read and observe all the important notices on the appliance.
This appliance has a polarized plug (one blade is wider than
the other). As a safety feature, this plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully
inserted. Do not attempt to defeat this safety feature.
This appliance is intended FOR HOUSEHOLD USE ONLY.
If an extension cord is necessary, a cord with a proper rating
should be used.






CLEANING




It is important to keep the SkkyeLight SingleStrip clean.
Always unplug the SingleStrip before performing maintenance or cleaning.
Wipe exposed surfaces carefully with a damp cloth to remove
any dust or mineral deposits which may collect over time.
Make sure hands are dry before re-plugging into an approved
electrical outlet
4
PARTS
Exploded View
#
1
Description
SingleStrip Bracket
Item Code
640001
2
Side Cap (Rt)
640002
3
12” Aluminum Shell
640026
4
Side Cap (Lt)
640003
5
Power Cord Grommet
640004
6
Power Cord
640005
7
Sliding Extension Rods
640006
8
3x1Watt LED-10K
640007
3x1Watt LED-14K
640008
3x1Watt LED-456nm
640009
9
Independent LED Reflector
640010
10
12”Aluminum Heat Sink Plate
640011
11
12” Acrylic Lens
640016
12
LED Driver (6W)*1
610006
5
PARTS
Exploded View
#
1
Description
SingleStrip Bracket
Item Code
640001
2
Side Cap (Rt)
640002
3
18” Aluminum Shell
640027
4
Side Cap (Lt)
640003
5
Power Cord Grommet
640004
6
Power Cord
640005
7
Sliding Extension Rods
640006
8
3x1Watt LED-10K
640007
3x1Watt LED-14K
640008
3x1Watt LED-456nm
640009
9
Independent LED Reflector
640010
10
18”Aluminum Heat Sink Plate
640012
11
18” Acrylic Lens
640017
12
LED Driver (9W to 12W)*1
640022
6
PARTS
Exploded View
#
1
Description
SingleStrip Bracket
Item Code
640001
2
Side Cap (Rt)
640002
3
24” Aluminum Shell
640028
4
Side Cap (Lt)
640003
5
Power Cord Grommet
640004
6
Power Cord
640005
7
Sliding Extension Rods
640006
8
3x1Watt LED-10K
640007
3x1Watt LED-14K
640008
3x1Watt LED-456nm
640009
9
Independent LED Reflector
640010
10
24”Aluminum Heat Sink Plate
640013
11
24” Acrylic Lens
640018
12
LED Driver (12W)*1
640023
7
PARTS
Exploded View
#
1
Description
SingleStrip Bracket
Item Code
640001
2
Side Cap (Rt)
640002
3
36” Aluminum Shell
640029
4
Side Cap (Lt)
640003
5
Power Cord Grommet
640004
6
Power Cord
640005
7
Sliding Extension Rods
640006
8
3x1Watt LED-10K
640007
3x1Watt LED-14K
640008
3x1Watt LED-456nm
640009
9
Independent LED Reflector
640010
10
36”Aluminum Heat Sink Plate
640014
11
36” Acrylic Lens
640019
12
LED Driver—(9W to 12W)*2
640022
8
PARTS
Exploded View
#
1
Description
SingleStrip Bracket
Item Code
640001
2
Side Cap (Rt)
640002
3
48” Aluminum Shell
640030
4
Side Cap (Lt)
640003
5
Power Cord Grommet
640004
6
Power Cord
640005
7
Sliding Extension Rods
640006
8
3x1Watt LED-10K
640007
3x1Watt LED-14K
640008
3x1Watt LED-456nm
640009
9
Independent LED Reflector
640010
10
48”Aluminum Heat Sink Plate
640015
11
48” Acrylic Lens
640020
12
LED Driver—(9W to 12W) *2
640022
9
INTRODUCTION
SkkyeLight LED series set the new standard for ultra-modern design in high brightness LED green technology. Reward your mini
Ecosystem with mesmerizing glitter lines while consuming a fraction
of the energy cost and minimal carbon emissions into our environment.
SingleStrip LED are the affordable turnkey solution for fresh &
saltwater fish or reef aquariums with out the fuss. From lighting
your 10gallon aquarium to saltwater show tank the SingleStrip is
the perfect choice. Housed in a sleek aluminum casing and
standard with Sliding Extension Rods that securely attach onto
rimless and framed aquariums or can be easily retrofitted into
canopies with the retrofit hardware kit.
Each high brightness LED boast an incredible 120 lumen per watt
with individual reflectors with 120 degree optics for wide uniform
coverage. Offered in 12”, 18”, 24’, 36”, 48”.
10
INTRODUCTION
SPECS—
MODEL
DIMENSIONS
6401
6402
6403
12” x 3.0” x 3.5” 12” x 3.0” x 3.5” 12” x 3.0” x 3.5”
6 x 1 Watt
6 x 1 Watt
6 x 1 Watt
COLOR
10,000K
14,000K
456nm
CURRENT
350 mA
350 mA
350 mA
6404
6405
6406
LED WATTS
SPECS—
MODEL
DIMENSIONS
18” x 3.0” x 3.5” 18” x 3.0” x 3.5” 18” x 3.0” x 3.5”
9 x 1 Watt
9 x 1 Watt
9 x 1 Watt
COLOR
10,000K
14,000K
456nm
CURRENT
350 mA
350 mA
350 mA
6407
6408
6409
LED WATTS
SPECS—
MODEL
DIMENSIONS
24” x 3.0” x 3.5” 24” x 3.0” x 3.5” 24” x 3.0” x 3.5”
15 x 1 Watt
15 x 1 Watt
15 x 1 Watt
COLOR
10,000K
14,000K
456nm
CURRENT
350 mA
350 mA
350 mA
LED WATTS
11
INTRODUCTION
SPECS—
MODEL
DIMENSIONS
6410
6411
6412
36” x 3.0” x 3.5” 36” x 3.0” x 3.5” 36” x 3.0” x 3.5”
18 x 1 Watt
18 x 1 Watt
18 x 1 Watt
COLOR
10,000K
14,000K
456nm
CURRENT
350 mA
350 mA
350 mA
6413
6414
6415
LED WATTS
SPECS—
MODEL
DIMENSIONS
48” x 3.0” x 3.5” 48” x 3.0” x 3.5” 48” x 3.0” x 3.5”
24 x 1 Watt
24 x 1 Watt
24 x 1 Watt
COLOR
10,000K
14,000K
456nm
CURRENT
350 mA
350 mA
350 mA
LED WATTS
12
INTRODUCTION
SingleStrip
Features:








Individual Reflectors
2” Sliding Aluminum Rods & Tank Mounts
1 Watt High Brightness LEDs
Integrated Driver
Color Spectrums—Available in 10K, 14K, 456nm
Sizes Available in 12”, 18”,24”, 36”, 48”
Low Profile—3” High
120 Lumens per watt
12”
18”
24”
36”
48”
13
GETTING STARTED
HANDLING PRECAUTION



Do not use cleaners that contain ammonia to clean the
SingleStrip surface.
Always unplug light when performing any maintenance
on SingleStrip.
Make sure
CHOOSING A LOCATION



Place SingleStrip in a ventilated area.
Use the integrated Sliding Extension Rods to adjust the
length of SingleStrip to place over Framed or Rimless
Aquarium.
If using SingleStrip inside Canopy make sure the Canopy
is properly ventilated.
14

Slide out Extension Rods
of each end of the Single
Strip to fit Framed Aquarium.(Fig.1)

Place the Arm on the outer edge of the Frame.
Fig 1
(Fig.2)
Fig 2

Push in the Extension
Rods to securely fit the
Framed Aquarium. (Fig.3)
Fig 3
15
GETTING STARTED
SKYYELIGHT SINGLESTRIP ON FRAMED TANK
GETTING STARTED
SKYYELIGHT SINGLESTRIP ON RIMLESS TANK

Slide out Extension Rods
of each end of the Single
Strip to fit Rimless Aquarium.(Fig.1)
Fig 1

Place the Arm on the outer edge of the Rim.(Fig.2)
Fig 2

Push in the Extension
Rods to securely fit the
Rimless Aquarium. (Fig.3)
Fig 3
16
GETTING STARTED
MOUNTING SINGLE STRIP INSIDE CANOPY



Retrofit Mounting Bracket is sold separately.
Push the Sliding Extension Rods inside both Left and
Right Side Caps
Remove the screws from both Right and Left Side Caps.
(Fig.1)

Line up the screw holes on Retrofit Mounting Bracket and
Side Caps. (Fig 2)

Tighten Retrofit Mounting Brackets to SingleStrip.

Mount the SingleStrip inside Canopy
17
GETTING STARTED
CUSTOMIZING YOUR LIGHTING WITH SINGLESTRIP



Pick between 3 color spectrums and meet your needs for
fish only to reef aquariums.
Make sure the width of the aquarium will fit multiply SingleStrips.
Each SingleStrip has a width of 3.5”
POWERING UP UTILITY 6


Each SingleStrip has integrated drivers and a single power
cord.
Once the Single Strip is placed on your Aquarium plug
your SingleStrip LED into an approved household timer
18
19
20
NOTES
NOTES
21
LIMITED WARRANTY
WARRANTY INFORMATION
LIMITED 1 YEAR WARRANTY—
UTILITY 6W
This SINGLESTRIP has a 1 YEAR limited warranty. The SINGLESTRIP warranted to the original purchaser against defective material and workmanship for 1 YEAR from the date of
original purchase. This warranty is valid only under the following conditions: additions, modifications, or changes made to the
product by the purchaser and not by the manufacturer shall
void this warranty. Damages brought on by abuse, misapplication, or mishandling also voids this warranty.
This warranty is limited to the repair or replacement of the product at the discretion of the manufacturer. This warranty does
not cover personal injury, property loss, including livestock or
damage (direct, incidental, or consequential) arising out of use
of this product. This warranty gives you specific rights and you
may also have other rights, which may vary from state to state.
The Product Registration Card must be filled out completely
and returned within (14) days from the date of purchase. Failure to do so will void this warranty. A proof of purchase from
an authorized dealer must be provided when making a warranty claim.
For Warranty Claim please contact our Customer Care Department.
A RMA # must be issued before sending any product back to
Innovative Marine. Products sent back to Innovative Marine
without a RMA# will be not be accepted. Service on products
will not extend the original warranty period.
Email: [email protected]
22
OWNER’S PRODUCT
INFORMATION
PRODUCT INFORMATION
MODEL #
SINGLESTRIP
DATE OF
PURCHASE
Please keep your receipt in a safe place to ensure you have this information.
23
WWW.INNOVATIVE-MARINE.COM
A Division of
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement