User manual

User manual
OWNER’S MANUAL
LG Digital
Signage
(MONITOR SIGNAGE)
Please read this manual carefully before operating the your set and retain it
for future reference.
32SM5B
43SM5B
49SM5B
55SM5B
65SM5B
32SM5KB
43SM5KB
49SM5KB
55SM5KB
65SM5KB
43SM3B
49SM3B
55SM3B
www.lg.com
2
ENGLISH
TABLE OF CONTENTS
3
IMPORTANT PRECAUTIONS
3
4
4
5
Electrical Power Related Precautions
Precautions in installing the Product
Precautions in Moving the Product
Precautions in Using/Cleaning the
Product
On Disposal (Only, Hg lamp used LCD
Monitor)
5
6LICENSES
7
ASSEMBLY AND PREPARATION
8
10
10
11
12
14
15
16
Optional Accessories
Parts and Buttons
Assembling the Memory Cover
Connecting the Stand
Connecting the Speakers
Connecting the IR Sensor
Portrait Layout
Attaching and removing the LG Logo
Bracket
Installing on a Wall
17
19
REMOTE CONTROL
21
MAKING CONNECTIONS
21
21
22
Connecting to a PC
External Device Connection
Using the Input List
23TROUBLESHOOTING
26
PRODUCT SPECIFICATIONS
WARNING: This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
3
Please read these safety precautions carefully before using the
product.
WARNING
Failure to follow those warnings may result in death, serious
injury or damage to the product or other property.
•• Do not insert metal or other conductive materials into the product
openings. Additionally, do not touch the power cable right after
plugging into the wall input terminal.
►►You may be electrocuted.
•• The appliance coupler is used as the disconnect device.
•• Please make sure the device is installed near the wall outlet to
which it is connected and that the outlet is easily accessible.
•• Do not unplug the power cord while the product is in use.
►►Electrical shock can damage the product.
WARNING
•• Indoor Use Only.
Electrical Power Related Precautions
WARNING
•• Use only the power cord supplied with the unit or another
manufacturer's authorized cord.
►►Failure to do so may result in fire or electrical shock or damage to
the product.
•• Use only a properly grounded plug and receptacle.
►►If you do not you may be electrocuted or injured. Or the product
might be damaged.
•• Do not use a damaged or loose plug.
►►This may cause electrical shock or fire.
•• Operate the display only from a power source(i.e. voltage)
indicated in the product specification.
►►Otherwise the product can be damaged, fire can occur or you may be
electrocuted. If you are not sure what type of power supply you have,
consult a certified electrician.
•• In the presence of thunder and lightning, never touch the power
cord and signal cable because it can be very dangerous.
►►It can cause electric shock.
•• Do not connect several extension cords, electrical appliances
or electrical heaters to a single outlet. Use a power bar with a
grounding terminal designed for exclusive use with the computer.
►►A fire can break out due to overheating.
•• Do not touch the power plug with wet hands. Additionally, if
the cord pin is wet or covered with dust, dry the power plug
completely or wipe dust off before plugging in the cord.
►►You may be electrocuted due to excess moisture.
•• If you don’t intend to use the product for a long time, unplug the
power cable from the product.
►►Covering dust can cause a fire, or insulation deterioration can cause
electric leakage, electric shock or fire.
•• Insert the power plug firm so it cannot come loose.
►►A loose connection can cause fire.
•• Hold the plug when pulling out the power cable. Do not pull the
plug out by the wire. Do not bend the power cord with excessive
force or put heavy objects on the power cord.
►►The power line can be damaged, which may cause electric shock
or fire.
•• As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if the unit is turned
off.
ENGLISH
Important Precautions
4
ENGLISH
Precautions in installing the Product
WARNING
•• Keep away from heat sources like eaters or open flames.
►►Electrical shock, fire, malfunction or deformation may occur.
•• Keep the packing anti-moisture material or vinyl packing out of
the reach of children.
►►Anti-moisture material is harmful if swallowed. If swallowed by
mistake, force the patient to vomit and visit the nearest hospital.
Additionally, vinyl packing can cause suffocation. Keep it out of the
reach of children.
•• Do not put heavy objects on the product on sit upon it.
►►If the product collapses or is dropped, you may be injured. Children
must pay particular attention.
•• Do not leave the power or signal cable where someone can trip
over it.
•• Do not place the product on the floor.
►►Small Children and others may trip over it.
•• Do not install this product on a wall if it could be exposed to oil
or oil mist.
►►This may damage the product and cause it to fall.
•• For displays with glossy bezels the user should consider the
placement of the display as the bezel may cause disturbing
reflections from surrounding light and bright surfaces.
Precautions in Moving the Product
WARNING
•• Make sure to turn off the product.
►►You may be electrocuted or the product can be damaged.
•• Make sure to remove all cables before moving the product.
►►You may be electrocuted or the product can be damaged.
►►The passerby can falter, which can cause electrical shock, fire, product
breakdown or injury.
•• When lifting or moving the product, do not hold it upside down
while holding only the stand.
►►Dust or moisture can cause electrical shock, fire or product damage.
•• Do not shock the product when moving it.
•• Install the product in a neat and dry place. Do not use near water.
•• Do not add accessories that have not been designed for this
display.
•• If you smell smoke or other odors or hear a strange sound from the
product unplug the power cord and contact LG Customer Service.
►►If you continue to use without taking proper measures, electrical
shock or fire can occur.
•• If you dropped the product or the case is broken, turn off the
product and unplug the power cord.
►►If you continue to use without taking proper measures, electrical
shock or fire can occur. Contact LG Customer Service.
•• Do not drop an object on or apply impact to the product. Do not
throw any toys or objects at the product.
►►It can cause injury to humans, problems to the product and damage
the display.
•• Keep out of reach of children and do not place toys near the
product.
•• Make sure the product ventilation hole is not blocked. Install the
product more than 10cm from the wall.
►►If you install the product too close to the wall, it may be deformed or
fire can break out due to internal heat build-up.
•• Do not cover the product with cloth or other material (eg. plastic)
while plugged in.
►►The product can be deformed or fire can break out due to internal
overheating.
•• Place the product on a flat and stable surface that is large enough
to support the product.
►►If the product is dropped, you may be injured or the product may
be broken.
•• Install the product where no Electromagnetic Interference occurs.
•• Keep the product away from direct sunlight.
►►The product can be damaged.
►►This may cause the product to fall resulting in damage or injury.
►►You may be electrocuted or the product can be damaged.
•• Make sure the panel faces forward and hold it with both hands
to move.
►►If you drop the product, the damaged product can cause electric
shock or fire.
•• Do not place the product face down.
►►This may damage the TFT-LCD screen.
5
WARNING
•• Do not attempt to disassemble, repair or modify the product
yourself.
►►Fire or electric shock can occur.
►►Contact LG Customer Service for repair.
•• When cleaning the product, unplug the power cord and scrub
gently with a soft cloth to prevent scratching. Do not clean with a
wet cloth or spray water or other liquids directly onto the product.
An electric shock may occur. (Do not use chemicals such as
benzene, paint thinners or alcohol)
•• Keep the product away from water.
►►Fire or electric shock accident can occur.
•• Avoid high temperatures and humidity.
•• Do not put or store flammable substances near the product.
►►There is a danger of explosion or fire.
•• Keep the product clean at all times.
•• Take a comfortable and natural position when working with the
product.
•• Take a regular break when working with the product for a long
time.
•• Do not press on the panel with a hand or sharp object such as nail,
pencil or pen, or make a scratch on it.
•• Keep proper distance from the product and rest from time-to-time.
►►Your vision may be impaired if you look at the product too closely
or for too long.
•• Set the appropriate resolution by referring to the User’s Guide.
•• Keep small accessories out of the reach of children.
•• Displaying a still image for long time on the monitor may leave
persistent image or stain on the monitor screen. To avoid this
problem, use a screen saver and power off when this product is not
used. Persistent image or stain caused by long time usage are not
covered by the warranty on this product.
•• Do not use products using high voltage around the Monitor. (ex.
Electrical Swatter)
►►Monitor may have malfunction as its electrical shock.
•• Spray water onto a soft cloth 2 to 4 times, and use it to clean the
front frame;wipe in one direction only. Too much moisture may
cause staining.
On Disposal (Only, Hg lamp used LCD
Monitor)
•• The fluorescent lamp used in this product contains a small amount
of mercury.
•• Do not dispose of this product with general household waste.
•• Disposal of this product must be carried out in accordance to the
regulations of your local authority.
ENGLISH
Precautions in Using/Cleaning the
Product
6
ENGLISH
LICENSES
Supported licenses may differ by model. For more information of the licenses, visit www.lg.com.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
This DivX Certified® device has passed rigorous testing to ensure it plays DivX®
video. To play purchased DivX movies, first register your device at vod.divx.com.
Find your registration code in the DivX VOD section of your device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
DivX®, DivX Certified®and associated logos are trademarks of DivX, LLC and are
used under license.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668;
7,515,710; 7,519,274.
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS
Licensing Limited. DTS, DTS-HD, the Symbol, & DTS or DTS-HD and the Symbol
together are registered trademarks of DTS, Inc. © DTS, Inc. All Rights Reserved.
NOTE
•• The warranty will not cover any damage caused by using the product in an excessively dusty environment.
7
CAUTION
•• Always use genuine components to ensure safety and product performance.
•• The product warranty will not cover damage or injury caused by the use of counterfeit components.
NOTE
•• The accessories provided with your product may vary depending on the model or region.
•• Product specifications or contents in this manual may be changed without prior notice due to upgrade of
product functions.
•• SuperSign Software & Manual
- Downloading from the LG Electronics website.
- Visit the LG Electronics website (www.lgecommercial.com/supersign) and download the latest software for
your model.
ENGLISH
ASSEMBLY AND PREPARATION
8
ENGLISH
Optional Accessories
Without prior notice, optional accessories are subject to change to improve the performance of the product,
and new accessories may be added. The illustrations in this manual may differ from the actual product and
accessories.
Screws
Diameter 4.0 mm x Pitch 0.7 mm
Stand
Spacers
Stand
ST-322T
32SM5*
ST-432T
43SM5*/43SM3B
49SM5*/55SM5*
49SM3B/55SM3B
65SM5*
ST-492T
ST-652T
32SM5*
43SM5*
43SM3B
49SM5*
49SM3B
55SM5*
55SM3B
65SM5*
Length
Model
-
2 EA
32SM5*
43SM5*
43SM3B
49SM5*
49SM3B
55SM5*
55SM3B
65SM5*
(including
spring washer)
Quantity
10 mm
6 EA
14 mm
8 EA
14 mm
8 EA
14 mm
8 EA
16 mm
8 EA
Stand kit
Speakers
SP-5000
Cable holder/
Cable Tie
Screws
Diameter 4.0 mm x Pitch
0.7 mm x Length 8 mm
(including spring washer)
Speaker kit
(Only for **SM5B, **SM3B model)
Screws
Diameter 4.0 mm x Pitch
1.6 mm x Length 10 mm
9
ENGLISH
Media Player
MP500/ MP700
Screws
CD (Owner's Manual)/
Cards
Media Player kit
( It may not be supported depending on the model.)
KT-OPSA
Screws
Connecting
Cable
Card
(Easy Setup Guide)
OPS kit
KT-SP0
Pixel sensor kit
NOTE
•• Cable holder/cable tie may not be available in some areas or for some models.
•• Optional accessories are available for some models. If necessary, please purchase them separately.
•• Pixel sensor is sold separately. You can obtain additional accessories from your local retail store.
•• Before you attach the OPS kit or Media Player, connect the cable to the port.
Power Cord
10
ENGLISH
Parts and Buttons
- The image may be different according to the
model.
Assembling the Memory Cover
Assemble the cover with a screw as illustrated to
prevent the USB memory from theft.
1
2
Buttons
yy
yy
:Changes the input source.
: Accesses the main menus, or saves your
yy
yy
yy
:A
djust the up and down.
: Moves left and right.
:D
isplays the current signal and mode.
input and exits the menus.
yy
/I: Turns the power on or off.
11
- For certain models only.
- The image may be different according to the
model.
43/49/55/65SM5*
1
32SM5*
1
2
2
3
43/49/55SM3B
ENGLISH
Connecting the Stand
12
ENGLISH
Connecting the Speakers
- For certain models only.
- The image may be different according to the
model.
32SM5B
1
3
Then connect the speaker cable. After installing
your speakers, use holders and cable ties to
organize the speaker cables.
Basic installation
Connect an input signal cable before installing
the speakers.
Installation with OPS connected
2
Mount the speakers by using screws as
shown below. Make sure the power cable is
disconnected before making a connection.
Basic installation
Installation with OPS connected
13
1
43/49/55SM3B
Connect an input signal cable before installing
the speakers.
2
Mount the speakers by using screws as
shown below. Make sure the power cable is
disconnected before making a connection.
3
Then connect the speaker cable. After installing
your speakers, use holders and cable ties to
organize the speaker cables.
NOTE
•• Please turn off the power before removing the
cable. Connecting or removing the speaker
cable while turned on may result in no sound.
ENGLISH
43/49/55/65SM5B
14
ENGLISH
Connecting the IR Sensor
When you connect the cable to the product, the feature for receiving remote control signals is activated. Rotate
the IR sensor according to the screen orientation (Landscape/Portrait).
- The image may be different according to the model.
Basic installation
<Front>
<Rear>
<Front>
<Rear>
<Front>
<Rear>
Landscape scene
Portrait scene
15
When installing in a portrait layout, rotate the
monitor counterclockwise 90 degrees (when facing
the screen).
Using Kensington Lock
(This is not available for all models.)
The Kensington security system connector is
located at the back of the monitor. For more
information on installation and use of this system,
refer to the manual provided with the Kensington
security system or visit http://www.kensington.
com.
Connect the Kensington security system cable
between the monitor and a table.
NOTE
••The Kensington security system is optional. You
can obtain additional accessories from most
electronics retail stores.
ENGLISH
Portrait Layout
16
ENGLISH
Attaching and removing the LG Logo Bracket
- For certain models only.
- The image may be different according to the model.
Removing the LG Logo
1Lay a clean cloth on the floor, and then put the
monitor on it with the screen face down. Using
a screwdriver, remove the screw that secures
the LG Logo Bracket to the bottom rear of the
monitor.
Attaching the LG Logo on the right side
1Lay a clean cloth on the floor, and then put the
monitor on it with the screen face down. Using
a screwdriver, remove the screw that secures
the LG Logo Bracket to the bottom rear of the
monitor.
LG Logo Bracket
2
After removing the screw, remove the LG Logo.
When re-attaching the LG Logo, repeat the process
in reverse order.
2
After removing the screw, remove the LG Logo.
Attach the LG Logo Bracket with a screw, aligning it
with the hole on the right side.
17
To install your monitor on a wall, attach a wall
mounting bracket (optional part) to the back of the
monitor.
For proper ventilation, allow a clearance of 10
cm on each side and from the wall. Detailed
installation instructions are available from your
dealer, see the optional Tilt Wall Mounting Bracket
Installation and Setup Guide.
Make sure that the wall mounting bracket is
securely fixed to the monitor and to the wall.
1
Use only screws and wall mounting brackets
that conform to VESA standards.
2Screws which are longer than standard length
may damage the inside of the monitor.
3
A non-VESA standard screw may damage
the product and cause the monitor to fall. LG
Electronics is not liable for any accidents related
to the use of non-standard screws.
4
Please use VESA standard as below.
10 cm
10 cm
••785 mm and above
10 cm
10 cm
10 cm
* Fixing screws: Diameter 6.0 mm x Pitch
1.0 mm x Length 12 mm
785 mm
CAUTION
••Disconnect the power cord before moving or installing the monitor to avoid risk of electric shock.
••If you install the monitor on a ceiling or slanted wall, it may fall and result in injury. Use an authorized LG wall
mount and contact your local dealer or qualified personnel to assist with the installation.
••Do not over tighten the screws as this may damage the monitor and void your warranty.
••Use only screws and wall mounting brackets that meet the VESA standard. Any damage or injuries caused by
misuse or use of improper accessories are not covered by the warranty.
NOTE
••The wall mount kit includes the installation guide and all necessary parts.
••The wall mounting bracket is optional. You can obtain additional accessories from your local dealer.
••The length of screws required may differ depending on the wall mount. Be sure to use the correct length.
••For more information, please refer to the guide provided with the wall mount.
ENGLISH
Installing on a Wall
18
ENGLISH
Securing the monitor to a wall (optional)
(Procedure may differ depending on the model.)
1
Insert and tighten the eyebolts, or brackets and
bolts on the back of the monitor.
- If there are already bolts inserted in the
eyebolts’ position, remove the other bolts first.
2
Mount the wall brackets with the bolts to the
wall. Match the location of the wall bracket and
the eyebolts on the rear of the monitor.
3
Connect the eyebolts and wall brackets tightly
with a sturdy cord.
Make sure the securing cord is horizontal with
the flat surface.
WARNING
••If the monitor is not positioned in a sufficiently stable location, there is a danger that it will fall. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
»» Using cabinets or stands recommended by the manufacturer.
»» Only using furniture that can safely support the monitor.
»» Ensuring the monitor is not overhanging the edge of the supporting furniture.
»» Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both
the furniture and the monitor to a suitable support.
»» Not placing cloth or other materials between the monitor and supporting furniture.
»» Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
CAUTION
••Make sure that children do not climb on or hang from the monitor.
NOTE
••Use a platform or cabinet that is large and strong enough to support the monitor securely.
••Brackets, bolts, and cords are sold separately. You can obtain additional accessories from your local retail
store.
••The illustration shows a general example of installation and may look different from the actual product.
19
The descriptions in this manual are based on the buttons on the remote control. Please read this manual
carefully to use the monitor correctly.
To install batteries, open the battery cover, place batteries (1.5 V AAA) matching
labels inside the compartment, and close the battery cover.
and
terminals to the
To remove the batteries, perform the installation actions in reverse. The illustrations may differ from the actual
accessories.
CAUTION
••Do not mix old and new batteries, as this may
damage the remote control.
••Be sure to point the remote control toward the
remote control sensor on the monitor.
(POWER) Turns the monitor on or off.
MONITOR ON Turns the monitor on.
MONITOR OFF Turns the monitor off.
ENERGY SAVING( ) R
educes power consumption by adjusting peak
screen brightness.
INPUT Selects the input mode.
3D Used for viewing 3D videos. (This model does not support this.)
1/a/A Toggles between numerical and alphabetical.
(Depending upon the model, this feature may not be supported.)
Number and Alphabet buttons Enters numerical or alphabetical characters depending upon the setting.
(Depending upon the model, this feature may not be supported.)
CLEAR Deletes the entered numerical or alphabetical character.
(Depending upon the model, this feature may not be supported.)
Volume Up/Down Button Adjusts the volume.
ARC Selects the Aspect Ratio mode.
AUTO Automatically adjusts picture position and minimizes image
instability (available for RGB input only).(Depending upon the
model, this feature may not be supported.)
MUTE Mutes all sounds.
BRIGHTNESS Adjusts the brightness of the display. PAGE Function is not
supported in the this model. (Depending upon the model,
this feature may not be supported.)
ENGLISH
REMOTE CONTROL
20
ENGLISH
PSM Selects the Picture Mode.
HOME Activates the Launcher.
W.BAL Enters the White Balance menu.
SETTINGS Accesses the main menus or saves your input and exit menus.
S.MENU S uperSign menu key (Depending upon the model, this feature
may not be supported.)
Navigation Buttons Scrolls through menus or options.
OK Selects menus or options and confirms your input.
BACK A
llows you to move back one step in the user interaction function.
EXIT Quit all OSD tasks and applications.
A
llows you to control various multimedia devices to enjoy
multimedia simply by using the remote control through the
SimpLink menu. (Depending upon the model, this feature
may not be supported.)
TILE Selects the TILE Mode.
PICTURE ID ON/OFF When the Picture ID number matches the Set ID
number, you can control whichever monitor you
want in multi-display format.
USB Menu Control Buttons Controls media playback.
21
You can connect various external devices to your monitor. Change the input mode and select the external
device you want to connect. For more information about external device connections, see the user manual
provided with each device.
Connecting to a PC
Some of the cables are not provided.
This monitor supports the Plug & Play* feature.
* Plug & Play: a feature that enables a PC to recognize devices attached by the user without device
configuration or user intervention when powering up.
External Device Connection
Connect a HD receiver, DVD, or VCR player to the monitor and select an appropriate input mode.
Some of the cables are not provided. For the best picture and sound quality, connecting external devices to
your monitor using HDMI cables is recommended.
NOTE
••For the best image quality, using the monitor with HDMI connection is recommended.
••To comply with the specifications of the product, use a shielded interface cable with ferrite core, such as a
D-sub 15-pin cable and DVI-D/HDMI cable.
••If you turn the monitor on when the set is cold, the screen may flicker. This is normal.
••Sometimes red, green, or blue spots may appear on the screen. This is normal.
••Use a High Speed HDMI®/TM cable.
••Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may
not display or a connection error may occur.
••Recommended HDMI Cable Types
- High-Speed HDMI®/TM Cable
- High-Speed HDMI®/TM Cable with Ethernet
••If you cannot hear any sound in HDMI mode please check your PC settings. Some PCs require you to
manually change the default audio output to HDMI.
••If you want to use HDMI-PC mode, you must set your PC/DTV to PC mode.
••You may experience compatibility issues if you use HDMI-PC mode.
••Make sure the power cable is disconnected.
••If you connect a gaming device to the monitor, use the cable provided with the gaming device.
••It is recommended to use the speakers that are provided as optional accessories.
••High Speed HDMI®/TM cables transmit a HD signal up to 1080p and higher.
CAUTION
••Connect the signal input cable and tighten it by turning the screws clockwise.
••Do not press the screen with your finger for a prolonged period as this may result in temporary distortion on
the screen.
••Avoid displaying static images on the screen for a long period of time to prevent image burn. Use a
screensaver if possible.
••A wireless communication device near your monitor can affect the image.
ENGLISH
MAKING CONNECTIONS
22
ENGLISH
Using the Input List
yy RGB -> HDMI -> DVI-D -> DISPLAYPORT -> OPS
23
ENGLISH
TROUBLESHOOTING
No image is displayed
Problem
Action
Is the product power cord connected?
yy Check if the power cord is correctly plugged into the power
outlet.
yy The signal from the PC (video card) is out of the vertical or
horizontal frequency range of the product. Adjust the frequency
range by referring to the Specifications in this manual.
* Maximum resolution: 1920 x 1080 (60 Hz)
yy The signal cable between PC and product is not connected.
Check the signal cable.
yy Press the INPUT menu in the remote Control to check the input
signal.
oes the Out of range message
D
appear?
oes the Check signal cable message
D
appear?
The Unknown Product message appears when the product is connected.
Problem
Did you install the driver?
Action
yy Check if the Plug & Play function is supported by referring to the
video card user manual.
The screen image looks abnormal.
Problem
Is the screen position wrong?
The screen is displayed abnormally.
Action
yy Check if the video card resolution and frequency are supported
by the product. If the frequency is out of range, set to the
recommended resolution in the Control Panel Display Setting
menu.
yy The proper input signal is not connected to the signal port.
Connect the signal cable that matches with the source input
signal.
After-image appears on the product.
Problem
After-image appears when the
product is turned off.
Action
yy If you use a fixed image for a long time, the pixels may be
damaged. Use the screen-saver function.
yy When a dark image is displayed on the screen after an image
with high contrast (black and white or gray), this may cause
image sticking. This is normal for LCD screen products.
24
ENGLISH
The audio function does not work.
Problem
No sound?
Sound is too dull.
Sound is too low.
Action
yy See if the audio cable is connected properly.
yy Adjust the volume.
yy See if the sound is set properly.
yy Select the appropriate equalizer sound.
yy Adjust the volume.
Screen color is abnormal.
Problem
Action
Screen has poor color resolution (16
colors).
yy Set the number of colors to more than 24 bits (true color). Select
Control Panel - Display - Settings - Color Table menu in Windows.
Screen color is unstable or
mono-colored.
yy Check the connection status of the signal cable. Or, re-insert the
PC video card.
Do black spots appear on the screen?
yy Several pixels (red, green, white, or black color) may appear
on the screen, which can be attributable to the unique
characteristics of the LCD panel. This is not a malfunction of the
LCD.
The operation does not work normally.
Problem
The power suddenly turned off.
Action
yy Is the Timer set?
yy Check the power control settings. Power interrupted.
25
••Image sticking does not occur when using constantly changing images but may occur when using a fixed
image for an extended period of time. Therefore, it is recommended that you use the instructions below
to decrease the likelihood of image sticking occurring when using a fixed image. It is recommended that
you change the screen at least once every 12 hours at the very minimum; if done more frequently, the
prevention of image sticking is more effective.
Recommended operating conditions
1 Change the background and the character
2 Change the image using the same time
colors using the same time interval.
ID: UPM 123
PW: ****
interval.
ID: UPM 123
PW: ****
When changing colors, using complementary
colors helps to prevent image sticking.
Make sure that the characters or images before
changing the image remain in the same location
after changing the image.
What is image sticking?
Glass
BM
CF
BM
CF
BM
CF
OC
PI
LC
PI
TFT Layers
Glass
ITO or MoTi Pixel Layer
I D : UPM123
PW : ******
I D : UPM123
PW : ******
CF
When the LCD panel displays a static image for an
extended period of time, it can cause a voltage
difference between the electrodes that operate
the liquid crystals. When the voltage difference
between the electrodes builds up over time, liquid
crystals have a tendency to remain aligned in
one direction. During this process, a previously
displayed image remains visible. This phenomenon
is referred to as image sticking.
ENGLISH
CAUTION
26
ENGLISH
PRODUCT SPECIFICATIONS
The product specifications below may be changed without prior notice due to upgrade of product functions.
LCD screen
Screen type
Thin Film Transistor (TFT)
Video signal
Maximum resolution
Liquid Crystal Display (LCD) Screen
1920 x 1080 @ 60 Hz
- This may not be supported on some OS or graphic card
types.
1920 x 1080 @ 60 Hz
Recommended
resolution
Horizontal frequency
- This may not be supported on some OS or graphic card
types.
RGB : 30 kHz to 83 kHz
Vertical frequency
HDMI/ DVI-D/ DisplayPort : 30 kHz to 83 kHz
RGB : 56 Hz to 75 Hz
Synchronization
HDMI/ DVI-D/ DisplayPort : 56 Hz to 60 Hz
Separate Sync, Digital
Input/output ports
**SM5B/**SM3B
**SM5KB
Embedded battery
Environmental
Conditions
Operating Temperature
Applied
0 °C to 40 °C
Operating Humidity
Storage Temperature
10 % to 80 %
-20 °C to 60 °C
Storage Humidity
5 % to 95 %
SD, USB, LAN, RGB IN, DP In/Out, DVI-D
IN, OPS, Speaker OUT, IR & Light sensor,
Pixel Sensor, HDMI, RS-232C In/Out,
Audio In/Out
SD, USB, LAN, RGB IN, DP In/Out, DVI-D
IN, OPS, IR & Light sensor, Pixel Sensor,
HDMI, RS-232C In/Out, Audio In/Out
* Applicable only for models that support the speakers
Audio/AUDIO
RMS Audio Output
10 W + 10 W (R + L)
Input Sensitivity
0.7 Vrms
Speaker Impedance
6Ω
refers to alternating current (AC), and
refers to direct current (DC).
27
LCD screen
Pixel pitch
0.36375 mm (H) x 0.36375 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 1.4 A
Power consumption
On Mode: 60 W Typ.
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
729.4 mm x 428.9 mm x 55.5 mm / 5.2 kg
729.4 mm x 481 mm x 154.2 mm / 6 kg
729.4 mm x 428.9 mm x 95.7 mm / 5.7 kg
729.4 mm x 481 mm x 154.2 mm / 6.5 kg
Pixel pitch
0.36375 mm (H) x 0.36375 mm (V)
Rated power
AC 100-240 V~ 50/60 Hz 1.4 A
Power consumption
On Mode: 60 W Typ.
32SM5KB
LCD screen
Power
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Off Mode: ≤ 0.5 W
729.4 mm x 428.9 mm x 55.5 mm / 5.4 kg
729.4 mm x 481 mm x 154.2 mm / 6.2 kg
ENGLISH
32SM5B
28
ENGLISH
43SM5B
LCD screen
Power
Pixel pitch
0.4902 mm (H) X 0.4902 mm (V)
Rated power
AC 100-240 V~ 50/60 Hz 0.9 A
Power consumption
On Mode: 75 W Typ.
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
969.6 mm x 563.9 mm x 38.6 mm / 9.8 kg
969.6 mm x 622.2 mm x 193 mm / 12.3 kg
969.6 mm x 563.9 mm x 67.9 mm / 10.3 kg
969.6 mm x 622.2 mm x 193 mm / 12.8 kg
LCD screen
Pixel pitch
0.4902 mm (H) X 0.4902 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 0.9 A
Power consumption
On Mode: 75 W Typ.
Dimensions (Width
x Height x Depth) /
Weight
43SM5KB
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Off Mode: ≤ 0.5 W
969.6 mm x 563.9 mm x 54.0 mm / 10 kg
969.6 mm x 622.2 mm x 193 mm / 12.5 kg
Pixel pitch
0.4902 mm (H) X 0.4902 mm (V)
Rated power
AC 100-240 V~ 50/60 Hz 0.9 A
Power consumption
On Mode: 60 W Typ.
43SM3B
LCD screen
Power
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
969.6 mm x 563.9 mm x 38.6 mm / 9.8 kg
969.6 mm x 622.2 mm x 193 mm / 12.3 kg
969.6 mm x 563.9 mm x 67.9 mm / 10.3 kg
969.6 mm x 622.2 mm x 193 mm / 12.8 kg
29
LCD screen
Pixel pitch
0.55926 mm (H) X 0.55926 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 1.0 A
Power consumption
On Mode: 85 W Typ.
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
1102.2 mm x 638.5 mm x 38.6 mm / 14.1 kg
1102.2 mm x 696.8 mm x 219.6 mm / 17.4 kg
1102.2 mm x 638.5 mm x 67.9 mm / 14.6 kg
1102.2 mm x 696.8 mm x 219.6 mm / 17.9 kg
LCD screen
Pixel pitch
0.55926 mm (H) X 0.55926 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 1.0 A
Power consumption
On Mode: 85 W Typ.
Dimensions (Width
x Height x Depth) /
Weight
49SM5KB
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Head
Head + Stand
Off Mode: ≤ 0.5 W
1102.2 mm x 638.5 mm x 54.0 mm / 14.3 kg
1102.2 mm x 696.8 mm x 219.6 mm / 17.6 kg
LCD screen
Pixel pitch
0.55926 mm (H) X 0.55926 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 1.0 A
Power consumption
On Mode: 70 W Typ.
Dimensions (Width
x Height x Depth) /
Weight
49SM3B
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
1102.2 mm x 638.5 mm x 38.6 mm / 14.1 kg
1102.2 mm x 696.8 mm x 219.6 mm / 17.4 kg
1102.2 mm x 638.5 mm x 67.9 mm / 14.6 kg
1102.2 mm x 696.8 mm x 219.6 mm / 17.9 kg
ENGLISH
49SM5B
30
ENGLISH
55SM5B
LCD screen
Pixel pitch
0.630 mm (H) x 0.630 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 1.1 A
Power consumption
On Mode: 100 W Typ.
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
1238 mm x 714.9 mm x 38.6 mm / 17.3 kg
1238 mm x 773.4 mm x 219.6 mm / 20.6 kg
1238 mm x 714.9 mm x 67.9 mm / 17.8 kg
1238 mm x 773.4 mm x 219.6 mm / 21.1 kg
Pixel pitch
0.630 mm (H) x 0.630 mm (V)
Rated power
AC 100-240 V~ 50/60 Hz 1.1 A
Power consumption
On Mode: 100 W Typ.
55SM5KB
LCD screen
Power
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Off Mode: ≤ 0.5 W
1238 mm x 714.9 mm x 54.0 mm / 17.5 kg
1238 mm x 773.4 mm x 219.6 mm / 20.8 kg
Pixel pitch
0.630 mm (H) x 0.630 mm (V)
Rated power
AC 100-240 V~ 50/60 Hz 1.1 A
Power consumption
On Mode: 85 W Typ.
55SM3B
LCD screen
Power
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
1238 mm x 714.9 mm x 38.6 mm / 17.3 kg
1238 mm x 773.4 mm x 219.6 mm / 20.6 kg
1238 mm x 714.9 mm x 67.9 mm / 17.8 kg
1238 mm x 773.4 mm x 219.6 mm / 21.1 kg
31
LCD screen
Pixel pitch
0.744 mm (H) x 0.744 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 1.4 A
Power consumption
On Mode: 120 W Typ.
ENGLISH
65SM5B
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Head
Head + Stand
Head + Speaker
Head + Speaker + Stand
Off Mode: ≤ 0.5 W
1456.9 mm x 838 mm x 41.1 mm / 27.7 kg
1456.9 mm x 898.1 mm x 293.7 mm / 32.9 kg
1456.9 mm x 838 mm x 70.4 mm / 28.2 kg
1456.9 mm x 898.1 mm x 293.7 mm / 33.4 kg
LCD screen
Pixel pitch
0.744 mm (H) x 0.744 mm (V)
Power
Rated power
AC 100-240 V~ 50/60 Hz 1.4 A
Power consumption
On Mode: 120 W Typ.
Dimensions (Width
x Height x Depth) /
Weight
65SM5KB
Sleep Mode (RGB, DVI-D, HDMI): ≤ 1.0 W
Sleep Mode(DISPLAYPORT): ≤ 0.5 W
Dimensions (Width
x Height x Depth) /
Weight
Head
Head + Stand
Off Mode: ≤ 0.5 W
1456.9 mm x 838 mm x 56.5 mm / 27.9 kg
1456.9 mm x 898.1 mm x 293.7 mm / 33.1 kg
Wireless module(LGSBW41)Specifications
Wireless LAN
Bluetooth
Standard
IEEE 802.11a/b/g/n
Standard
Bluetooth Version 4.0
Frequency
range
2400 to 2483.5MHz
Frequency
range
2400 to 2483.5MHz
5150 to 5250 MHz
5725 to 5850 MHz
*Because band channel used by the country could be different, the user can not change or adjust
theoperating frequency and this product is set for the regional frequency table.
*This device should be installed and operated with minimum distance 20 cm between the device and your
body. And this phrase is for the general statement for consideration of user environment.
*Contains FCC ID: BEJLGSBW41 / Contains IC: 2703H-LGSBW41
32
ENGLISH
RGB (PC) Support Mode
HDMI / DISPLAYPORT / OPS (DTV) Support
Mode
Resolution
Horizontal
Vertical frequency
frequency (kHz) (Hz)
720 x 400
31.468
70.8
640 x 480
31.469
59.94
800 x 600
37.879
60.317
1024 x 768
48.363
60.0
1280 x 720
44.772
59.855
1280 x 960
60
60
1280 x 1024
63.981
60.02
1680 x 1050
65.29
59.954
1920 x 1080
67.5
60
HDMI / DVI-D / DISPLAYPORT / OPS (PC)
Support Mode
Resolution
Horizontal
Vertical frequency
frequency (kHz) (Hz)
640 x 480
31.469
59.94
800 x 600
37.879
60.317
1024 x 768
48.363
60
1280 x 720
44.772
59.855
1366 x 768
47.7
60
1280 x 1024
63.981
60.02
1680 x 1050
65.29
59.954
1920 x 1080
67.5
60
Resolution
Horizontal
Vertical frequency
frequency (kHz) (Hz)
480/60p
31.5
60
576/50p
31.25
50
720/50p
37.5
50
720/60p
45
60
1080/50i
28.1
50
1080/60i
33.75
60
1080/50p
56.25
50
1080/60p
67.5
60
NOTE
••PC resolutions available for the Input Label
option in RGB / HDMI / DVI-D / DISPLAYPORT
input modes: 640 x 480/60 Hz, 1280 x 720/60 Hz,
1920 x 1080/60 Hz; 480p, 720p, and 1080p DTV
resolutions.
••Vertical frequency: The product display
functions by the screen image changing dozens
of times every second like a fluorescent lamp.
The vertical frequency or refresh rate is the
number of image displays per second. The unit
is Hz.
••Horizontal frequency: The horizontal interval
is the time taken to display one horizontal line.
When 1 is divided by the horizontal interval,
the number of horizontal lines displayed every
second can be tabulated as the horizontal
frequency. The unit is kHz.
ENERGY STAR® is a set of power-saving
guidelines issued by the U.S.Environmental
Protection Agency (EPA).
As an ENERGY STAR® Partner LGE U. S. A., Inc. has
determined that this product meets the ENERGY
STAR® guidelines for energy efficiency. Refer to
ENERGY STAR.gov for more information on the
ENERGY STAR® program.
Make sure to read the Safety Precautions
before using the product.
The model and serial numbers of the SET are
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
NOTE
yy 65SM5B and 65SM5KB are not certified with
EPA’s ENERGY STAR.
WARNING -This is a class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
Temporary noise is normal when powering ON
or OFF this device.
USER GUIDE
MONITOR
SIGNAGE
WebOS
Please read this manual carefully before operating the your set and retain it
for future reference.
www.lg.com
2
ENGLISH
TABLE OF CONTENTS
3
USER SETTINGS
3
3
7
8
10
Main Menu Settings
- Picture Settings
- Sound Settings
- Network Settings
- General Settings
11ENTERTAINMENT
11
Using My Media
11
- Connecting USB/SD Storage Devices
13
- Files Supported by My Media
16
- Viewing Videos
17
- Viewing Photos
17
- Listening to Music
17 -Settings
18
- Moving, Copying, or Deleting a File
18
SuperSign Contents
18Information
19
Local Contents Scheduler
20
Screen Share
22
PICTURE ID Settings
23
IR CODES
25
TO CONTROL MULTIPLE
PRODUCTS
25
25
26
28
Connecting the Cable
Communication Parameter
Command Reference List
Transmission/Reception Protocol
To obtain the source code under GPL, LGPL,
MPL, and other open source licenses, that is
contained in this product, please visit http://
opensource.lge.com.
In addition to the source code, all referred
license terms, warranty disclaimers and
copyright notices are available for download.
LG Electronics will also provide open source
code to you on CD-ROM for a charge covering
the cost of performing such distribution (such
as the cost of media, shipping, and handling)
upon email request to [email protected]
This offer is valid for three (3) years from the
date on which you purchased the product.
3
••The software-related contents may be changed without prior notice due to upgrade of the product
functions.
User Settings
Main Menu Settings
Picture Settings
To Select Picture Mode
Advanced
Picture
Picture Mode Settings
Picture Mode
Select the picture mode that is best suited to the video type.
••Vivid:adjusts the video image for a retail environment by enhancing the contrast, brightness, and
sharpness.
••Standard: adjusts the video image for a normal environment.
••APS: APS (Auto power saving ) mode reduces power consumption by dimming control.
••Cinema: optimizes the video image for watching movies.
••Sports: optimizes the video image for watching sports. Even fast actions such as kicking or throwing a ball
are rendered clearly on the screen.
••Game: optimizes the video image for playing videogames.
••Expert/Calibration: allows an expert, or anyone interested in high quality pictures, to manually tune the
picture for the best picture quality.
NOTE
••Depending on the input signal, the available picture modes may differ.
••Expert is an option that allows a picture quality expert to fine-tune the picture quality using a specific
image. Thus, it may not be effective for a normal picture.
ENGLISH
NOTE
4
ENGLISH
To fine-tune the picture mode
Advanced
Picture
Picture Mode Settings
Customize
••Backlight: adjusts the brightness of the screen by controlling the LCD backlight. The closer the value is to
100, the brighter the screen is.
••Contrast: adjusts the difference between the light and dark areas of the picture. The closer the value is to
100, the greater the difference is.
••Brightness: adjusts the overall brightness of the screen. The closer the value is to 100, the brighter the
screen is.
••Sharpness: adjusts the sharpness of the edges of objects. The closer the value is 50, the clearer and the
sharper the edge becomes.
••H Sharpness: adjusts the sharpness of the contrast edges on the screen from a horizontal point of view.
••V Sharpness: adjusts the sharpness of the contrast edges on the screen from a vertical point of view.
••Color: softens or deepens the tints on the screen. The closer the value is 100, the deeper the colors become.
••Tint: adjusts the balance between red and green levels displayed on the screen. The closer the value is to
Red 50, the deeper the color red becomes, and the closer the value is to Green 50, the deeper the color
green becomes.
••Color Temperature: adjusts the tints of the screen to evoke feelings of warmth or coolness.
••Advanced Controls/Expert Control: customizes the advanced options.
–– Dynamic Contrast:Optimizes the difference between the light and dark parts of the screen according to the
brightness of the image.
–– Super Resolution: Sharpens the blurry or indistinguishable parts of the picture.
–– Color Gamut: Selects the range of colors to display.
–– Dynamic Color: Adjusts the tint and saturation of the image for a more vivid and lively display.
–– Edge Enhancer: Provides much sharper and clearer edges to the picture.
–– Color Filter: Accurately adjusts color and tint by filtering a specific color area of RGB space.
–– Preferred Color: Adjusts the skin tint, grass tint, and sky tint to your preference.
–– Gamma: Adjusts the medium brightness of the image.
–– White Balance: Adjusts the overall tint of the picture to your preference. In Expert mode, you can fine-tune the
picture using the Method/Pattern options.
–– Color Management System: E xperts use the color management system when they adjust the colors by using
the test pattern. The color management system allows you to make an adjustment
by selecting from among 6 different color spaces (Red/Yellow/Blue/Cyan/Magenta/
Green) without affecting other colors. You may not see tints change in a normal
picture even after adjustment.
5
––
––
––
––
Noise Reduction: Removes irregularly generated tiny dots for a clear picture.
MPEG Noise Reduction: Reduces the noise produced while creating digital video signals.
Black Level: Adjusts the black level of the picture to correct the brightness and contrast of the picture.
Real Cinema: Optimizes the video image for a cinematic look.
••Reset: resets the picture settings.
NOTE
••You can adjust advanced settings only in the User mode.
••Depending upon the input signal or the selected picture mode, the available options may differ.
To set the aspect ratio,
Advanced
Picture
Aspect Ratio
Changes the aspect ratio to view the image in its optimal size.
••16:9: displays the image with a 16:9 aspect ratio.
••Just Scan: displays the image in the original size without cutting off the edges.
Original is available in HDMI (720p or higher) mode.
••Set By Program: automatically changes the aspect ratio to 4:3 or 16:9 depending on the input video signal.
••4:3: displays the image with a 4:3 aspect ratio.
••Zoom: expands the image to fit to the width of the screen. The top and bottom of the image may be
cropped.
••Cinema Zoom: enlarges the image to have a cinemascope ratio of 2.35:1 without distortion.
CAUTION
••If a fixed image is displayed on the screen for a long period of time, it will be imprinted and become a
permanent disfigurement on the screen. This image burn or burn-in is not covered by the warranty.
••If the aspect ratio is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the
screen.
••The options may differ depending on the model.
••Depending on the input signal, the available aspect ratio may differ.
••You can select only 4:3 and 16:9 aspect ratios in HDMI-PC/ DVI-D/ DISPLAYPORT-PC/ OPS-PC input mode.
ENGLISH
••Picture Options: customizes the picture options.
6
ENGLISH
To use the Energy Saving function
Advanced
Picture
Energy Saving
Reduces power consumption by adjusting peak screen brightness.
••Auto: adjusts the brightness of the monitor according to ambient light. (This feature is available only with
certain models.)
••Off: disables the Energy Saving mode.
••Minimum/Medium/Maximum: uses the Energy Saving according to the Energy Saving level specified for
your monitor.
••Screen Off: turns off the screen. You will only hear audio. You can turn on the screen again by pressing any
button on the remote control except the power button.
To use the Smart Energy Saving function
Advanced
Picture
Smart Energy Saving
According to picture brightness, the brightness of the monitor will be adjusted automatically to save energy.
••Off: disables the Smart Energy Saving function.
••On: enables the Smart Energy Saving function.
To use the SCREEN(RGB-PC) function
Advanced
Picture
SCREEN(RGB-PC)
Customizes the PC display options in RGB mode.
••Set Automatically: S ets to adjust the screen position, clock, and phase automatically.
The displayed image may be unstable for a few seconds while the configuration is in
progress.
••Resolution: Selects a proper resolution.
••Position/Size/Phase: A
djusts the options when the picture is not clear, especially when characters are
shaky, after the auto configuration.
••Reset: Restores the options to the default setting.
To run a Picture Test
Advanced
Picture
Picture Test
Run a Picture Test to check that picture signals are outputted normally, then solve any problems by selecting
the relevant option on the screen. If there are no problems with the Test Picture, check connected external
devices.
7
To select a Sound Mode
Advanced
Sound
Sound Mode
The best sound quality will be selected automatically depending on the video type currently being watched.
••Standard: this sound mode works well for content of all types.
••Cinema: optimizes sound for watching movies.
••News: optimizes sound for watching news.
••Sports: optimizes sound for watching sports.
••Music: optimizes sound for listening to music.
••Game: optimizes sound for playing videogames.
To use the Sound Effects function
Advanced
Sound
Sound Effects
••Clear Voice ll: enjoy clearer sound with the three-level adjustment.
••Equalizer: manually adjust sound by using the equalizer. .
••Balance: adjust the output volume for the left speaker and the right speaker.
••Reset: reset the sound settings.
To select a Volume Increase Rate,
Advanced
Sound
Volume Increase Amount
you can set the volume range by selecting any of Low/ Medium/ High.
To sync audio with video
Advanced
Sound
AV Sync Adjustment
••Speaker: adjusts the sync between video and audio coming from external speakers, such as those
connected to the digital audio output port, LG audio equipment, or headphones. From the default
value, the closer the value is to -, the faster the sound output becomes, and the closer the value is
to +, the slower the sound output becomes.
••Bypass: audio coming from external devices without delay. Audio may be outputted earlier than video due
to the processing time for video that is inputted into the monitor.
To Run a sound test
Advanced
Sound
Sound Test
Run a sound test to check that sound signals are outputted normally, then solve any problems by selecting the
relevant option on the screen. If there are no problems with the Sound Test, check connected external devices.
ENGLISH
Sound Settings
8
ENGLISH
Network Settings
To Set a Signage Monitor Name
Advanced
Network
Signage Name
You can set a name for Signage Monitor that will be used on the network by using the on-screen keyboard.
To Set Your Wired Network
Advanced
Network
Wired Connection (Ethernet)
••Connecting to a wired network: Connect your monitor to a local area network (LAN) via the LAN port,
and configure the network settings. Only wired network connections
are supported. After making a physical connection, a small number of
networks may require the display network settings to be adjusted. For
most networks, the display will automatically make a connection without
any adjustments. For detailed information, contact your Internet provider
or consult your router manual.
Setting a Wireless Network
Advanced
Network
Wi-Fi Connection
If you have set the monitor up for a wireless network, you can check and connect to the available wireless
Internet networks.
••Add a Hidden Wireless Network: If you input the name of network directly, you can add a wireless network.
••Connect via WPS PBC: Connects easily when the button of a wireless AP supporting PBC is pressed.
••Connect via WPS PIN: Connects easily when the PIN of the wireless AP that you wish to connect to is entered
in to the AP configuration webpage.
••Advanced Settings: If you input the information of network directly, you can enter a wireless network.
If there is no wireless network available, click Advanced Settings. You can add a
network.
9
••Use a standard LAN cable (Cat5 or higher with a RJ45 connector) with this display.
••Many network connection problems during set-up can often be fixed by re-setting the router or modem.
After connecting the display to the home network, quickly power off and/or disconnect the power cable of
the home network router or cable modem, then power on and/or connect the power cable again.
••Depending on the Internet Service Provider (ISP), the number of devices that can receive Internet service
may be limited by the applicable terms of service. For details, contact your ISP.
••LG is not responsible for any malfunction of the display and/or the Internet connection feature due
to communication errors/malfunctions associated with your Internet connection, or other connected
equipment.
••LG is not responsible for problems with your Internet connection.
••You may experience undesired results if the network connection speed does not meet the requirements of
the content being accessed.
••Some Internet connection operations may not be possible due to certain restrictions set by the Internet
Service Provider (ISP) supplying your Internet connection.
••Any fees charged by an ISP including, without limitation, connection charges are your responsibility.
NOTE
••If you want to access the Internet directly on your display, the Internet connection should always be on.
••If you cannot access the Internet, check the network conditions from a PC on your network.
••When you use Network Setting, check the LAN cable or check if DHCP in the router is turned on.
••If you do not complete the network settings, the network may not function correctly.
CAUTION
••Do not connect a modular telephone cable to the LAN port.
••Since there are various connection methods, please follow the specifications of your telecommunication
carrier or Internet Service Provider.
••Network Setting menu will not be available until the display is connected to a physical network.
Tips for Wireless Network Setting
••Wireless networks can be subject to interference from other devices operating at a frequency of 2.4 GHz
(wireless phones, Bluetooth devices or microwave ovens). There may also be interference from devices with
a frequency of 5 GHz, same as other Wi-Fi devices.
••The surrounding wireless environment can cause the wireless network service to run slowly.
••If you do not turn off the entire local home network, network traffic may occur on some devices.
••For an AP connection, an access point device that supports wireless connection is required and the wireless
connection feature must be enabled on the device. Contact your service provider regarding availability of
wireless connection on your access point.
••Check the SSID and security settings of the AP for AP connection. Refer to the appropriate documentation
for SSID and security settings of the AP.
••Invalid settings on network devices (wired/wireless line sharer, hub) can cause the monitor to run slowly or
not operate properly. Install the devices correctly according to the appropriate manual and set the network.
••Connection method may differ according to the AP manufacturer.
ENGLISH
Tips for Network Setting
10
ENGLISH
General Settings
To configure the language
Advanced
General
Menu Language
Select one of the languages on the menu displayed on the screen.
••Menu Language: sets a language for Signage.
To set the time/date
Advanced
General
Time & Date
You can check or change the time.
••Set Automatically : You can set Time and Date.
••Daylight Saving Time: You can set Start Time and End Time for Daylight Saving Time.
••Time zone: You can change the settings for Continent, Country/Territory, and City.
To turn your monitor on or off automatically
Advanced
General
Timers
You can set the On/Off Timer for your monitor.
••On Timer: you can set the time when your monitor turns on.
••Off Timer: you can set the time when your monitor turns off.
••No Signal Power Off (15Min): When there is no input source, the monitor will automatically turn off after
15 minutes. If you don’t want it to turn off automatically, set No Signal Power
Off to Off.
••Auto Power Off: When there is no key input, the monitor will automatically turn off.
NOTE
••On Time/Off Time can be saved for up to seven schedules; the monitor is turned on or off at the preset time
in the schedule list. If multiple preset times are stored in the schedule list, this function works at the nearest
time from the current time.
••Once the on or off time is set, these functions operate daily at the preset time.
••The scheduled power-off function works properly only when the device time is set correctly.
••When the scheduled power-on and power-off times are the same, the power-off time has priority over the
power-on time if the set is turned on, and vice versa if the set is turned off.
To reset your monitor settings
Advanced
Resets all monitor settings.
General
Reset to Initial Settings
11
Using My Media
Connecting USB/SD Storage Devices
Connect a USB storage device such as a USB flash memory, SD storage devices or an external hard drive to the
display and use multimedia features.
CAUTION
••Do not turn off the monitor or remove a USB storage device when the My Media screen is activated. This
could result in loss of files or damage to the USB storage device.
••Back up files you have saved on a USB storage device frequently, as loss or damage to the files may be not
covered by the warranty.
ENGLISH
ENTERTAINMENT
12
ENGLISH
Tips for using USB/SD storage devices
••Only a USB storage device can be recognized.
••A USB device does not work effectively when it is connected via a USB hub.
••A USB storage device using an automatic recognition program may not be recognized.
••A USB storage device using its own driver may not be recognized.
••The recognition speed of a USB storage device may depend on each device.
••Please do not turn off the display or unplug the USB storage device when the connected device is working. If
the USB storage device is suddenly disconnected, the stored files or the device itself may be damaged.
••Please do not connect a USB storage device which was modified to work on a PC. The device may cause
the monitor to malfunction or the content fail to be played. Use only a USB storage device which contains
normal music, image or video files.
••A USB storage device formatted as a utility program not supported by Windows may not be recognized.
••A USB storage device (over 0.5 A) which requires an external power supply must be connected to a power
supply separately. If it is not, the device may not be recognized.
••Please connect the USB storage device using the cable provided by the device manufacturer.
••Some USB storage devices may not be supported or operate smoothly.
••File alignment method of USB storage devices is similar to that of Window XP and filenames can recognize
up to 100 English characters.
••Back up important files regularly as data stored on a USB storage device may be damaged. We will not be
responsible for any data loss.
••If the USB HDD does not have an external power source, the USB device may not be detected. To ensure the
device is detected, connect the external power source.
- Please use a power adapter for an external power source. We do not provide a USB cable for an external
power source.
••If your USB storage device has multiple partitions, or if you use a USB multi-card reader, you can use up to
four partitions or USB storage devices.
••If a USB storage device is connected to a USB multi-card reader, its volume data may not be detected.
••If the USB storage device does not work properly, disconnect and reconnect it.
••Detection speed differs from device to device.
••If the USB storage device is connected in Standby Mode, the specific hard disk will automatically be loaded
when the display is turned on.
••The recommended capacity is 1 TB or less for a USB external hard drive and 32 GB or less for USB memory
stick.
••Any device with more than the recommended capacity may not work properly.
••If a USB external hard drive with an “Energy Saving” function does not work, try turning the hard drive off
and on again.
••USB storage devices below USB 2.0 are also supported but may not function correctly in the Videos.
••A maximum of 999 sub-folders or files can be recognized under one folder.
••The SDHC type for SD cards is supported. To use an SDXC card, format it to the NTFS file system first.
••The exFAT file system is not supported for SD cards and USB storage devices.
13
Supported External Subtitle Format
••*.smi, *.srt, *.sub (MicroDVD, SubViewer 1.0/2.0), *.ass, *.ssa, *.txt (TMPlayer), *.psb (PowerDivX), *.dcs (DLP
Cinema), *.dcs (DLP Cinema)
To use Select Play,
Photos/ Videos/ Music/ All
••Play Selection: plays back selected content.
To set FILTER,
Photos/ Videos/ Music/ All
••FILTER: import contents from the selected device.
To set Scheduled Playing,
Photos/ Videos/ Music/ All
••Scheduled Playing: You can play the selected content at the scheduled time.
ENGLISH
Files Supported by My Media
14
ENGLISH
Supported Internal Subtitle Format
••FULL HD Video
1920 X 1080: XSUB (Supports internal subtitles generated from DivX6)
Supported Video Codec
Extension
Codec
.asf
.wmv
Videos
VC-1 Simple and Main Profiles
Audio
WMA Standard, WMA 10 Professional
.divx
.avi
Videos
DivX3.11, DivX4, DivX5, DivX6, XViD, H.264/AVC, Motion Jpeg, MPEG-4 Part2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, LPCM, ADPCM, DTS
.mp4
.m4v
.mov
Videos
H.264/AVC, MPEG-4 Part2
Audio
AAC, MPEG-1 Layer III (MP3)
.3gp
.3g2
Videos
H.264/AVC, MPEG-4 Part2
Audio
AAC, AMR-NB, AMR-WB
.mkv
Videos
H.264/AVC
Audio
HE-AAC, Dolby Digital
.ts
.trp
.tp
.mts
.m2ts
Videos
H.264/AVC, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, Dolby Digital Plus, AAC,
PCM
.mpg
.mpeg
Videos
MPEG-1, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), AAC
.vob
Videos
MPEG-1, MPEG-2
Audio
Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM
15
File Format
.MP3
Item
Information
Bit rate
32 Kbps to 320 Kbps
Sample freq.
16 KHz to 48 KHz
Support
MPEG1, MPEG2, Layer2, Layer3
Supported Photo File
File Format
2D (jpeg, jpg,
jpe)
Format
JPEG
Item
yy Minimum : 64 x 64
yy Maximum: Normal Type: 15360 (W) x 8640 (H) / Progressive Type: 1920 (W) x 1440
(H)
Supported Files and Formats for Content (with SuperSign Manager)
File extension
*.cts, *.sce
Video file
extension
*.mpg, *.mpeg, *.dat, *.ts, *.trp, *.tp, *.mp4, *.mkv, *.avi, *. avi(motion JPEG), *. mp4(motion JPEG),
*.mkv(motion JPEG)
Video format
MPEG1, MPEG2, MPEG4,H.264, DivX 3.11, DivX 4, DivX 5, DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid
1.03,Xvid 1.10-beta1/2, JPEG
Audio format
MP3, Dolby Digital, LPCM, AAC, HE-AAC
Web page
Only web pages that support iframe can be displayed.
ENGLISH
Supported Audio File
16
ENGLISH
Viewing Videos
Play video files on display. All of the saved video files are shown in your display.
To play video files on display
Videos
Tips for Playing Video Files
••Some user-created subtitles may not work properly.
••Some special characters in subtitles are not rendered.
••HTML tags are not supported in subtitles.
••Subtitles in languages other than the supported languages are not available.
••The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audio
language is changed.
••A damaged video file may not play correctly, or some player functions may not be usable.
••Video files produced with some encoders may not be played correctly.
••If the video and audio structure of a recorded file is not interleaved, either video or audio is outputted.
••Depending on the frame, HD videos with a maximum of 1920 x 1080 @ 25/30 P or 1280 x 720 @ 50/60P are
supported.
••Depending on the frame, videos with resolutions higher than 1920 x 1080 @ 25/30 P or 1280 x 720 @ 50/60 P
may not play correctly.
••Video files other than the specified types and formats may not play correctly.
••Maximum bit rate of playable video file is 20 Mbps. (Motion JPEG: 10 Mbps only)
••We cannot guarantee smooth playback of files encoded level 4.1 or higher in H.264 / AVC.
••Video files more than 30 GB in file size are not supported.
••A DivX video file and its subtitle file must be located in the same folder.
••A video file name and its subtitle file name must be identical for it to be displayed.
••Playing a video via a USB connection that does not support high-speed connection may not function
correctly.
••Files encoded with GMC (Global Motion Compensation) may not be played.
NOTE
••Option values changed in Videos do not affect the Photos and Music. and in turn are not affected by option
values changed in Photos or Music.
••Option values changed in Photos and Music do affect each other.
••When restarting a video file after stopping it, you can play from the point at which it was stopped.
••Only 10,000 sync blocks can be supported within the subtitle file.
••When playing a video, you can adjust the picture size by pressing the ARC button.
••Korean subtitle is supported only when the OSD menu is in Korean.
••The code page options may be disabled depending on the language of the subtitle files.
••Select the appropriate code page for the subtitle files.
17
Settings
The displays on the screen may differ from the
model.
You must register your product to play a DRMprotected DivX video.
Viewing image files
Photos
In order to register/deregister purchased or
rented DivX® VOD contents
Videos
Listening to Music
Viewing music files
Music
NOTE
••Files with unsupported extensions are not
displayed.
••If a file is invalid, a broken image and the
message "unrecognizable file" are displayed.
••Damaged music files are displayed as 00:00 and
will not be played.
••A music file downloaded from a paid service
with copyright protection will not play, and
incorrect information may be displayed during
playback.
••You can use
,
,
,
,
buttons on
the remote control also in this mode.
••You can use the
button to select the next
track and the
button to select the previous
track.
••If you press the
button within 5 seconds
after playing the song, you will return to the
previous song; if you press the same button
after 5 seconds, you will return to the start of
the song.
DivX® VOD
In order to play purchased or rented DivX® VOD
contents, you should register your device with 10
digit DivX registration code from your device at
www.divx.com/vod.
••Registration:view the registration code of your
display.
••Deregistration: cancel the registration.
NOTE
•• While you are checking the registration code,
some buttons may not work.
•• If you use the DivX registration code of another
device, you cannot play rented or purchased
DivX files. Use only the DivX registration code
assigned to your product.
•• Video or audio files that are not converted using
the standard DivX codec may be corrupted or
not play.
•• The DivX® VOD code allows you to activate up to
6 devices under one account.
•• After deregistration, you must register your
device again to see DivX® VOD contents.
ENGLISH
Viewing Photos
18
ENGLISH
Moving, Copying, or Deleting a
File
SuperSign Contents
You can move, copy, or delete files.
Plays stored files using the Export option in
SuperSign Editor.
To move, copy, or delete files
Devices
••You can move or copy files or folders from
internal to external memory.
••You can move or copy files or folders from
external to internal memory.
••You can delete files or folders from internal or
external memory.
NOTE
••Those files bigger than internal remaining
memory aren`t allowed to be copied or moved
to the internal memory.
To play back the stored files using the Export
option
Only contents distributed by SuperSign Manager
are displayed and selectable.
NOTE
••If there is an AutoPlay folder in the USB storage
device and its files are in supported formats,
they will be played back automatically when the
USB storage device is connected to the monitor.
Information
To check the basic information of Signage
Monitor
You can see the basic information on Signage
Monitor.
You can also switch to Smart Energy Saving
Mode or configure Fail Over settings. (You can
switch to Smart Energy Saving Mode only when
Energy Saving Mode is set to Off.)
19
You can view or delete any scheduled playing
created in MY MEDIA.
To view detailed information about a
scheduled playing
To access Local Contents Scheduler
Go to Local Contents Scheduler to check the list
of the scheduled playing created in MY MEDIA.
Select Scheduled Playing
••From list of the scheduled playing, select a
specific scheduled playing and view its detailed
information.
NOTE
••By default, Local Contents Scheduler lists the
scheduled playing created by the currently
connected devices.
To play scheduled playing instantly
Select Scheduled Playing
Play Button
To add new a scheduled playing
••NEW SCHEDULED PLAYING: In the pop-up
window, click the GO TO MY MEDIA button and
enter MY MEDIA to create new a scheduled
playing.
To configure FILTER
••FILTER: You can view the list by sorting it based
on the type of device used for creating the
scheduled playing.
To delete a scheduled playing
••DELETE: You can select a scheduled playing and
delete it.
••In the detailed information page of the
scheduled playing, click the Play button above
the thumbnail to play the scheduled playing
instantly.
NOTE
••To play a scheduled playing instantly rather than
at the scheduled time, the scheduled playing
must be in a playable status. In other words, the
device used for creating the scheduled playing
must be connected, and all the content included
in the scheduled playing must be valid.
ENGLISH
Local Contents Scheduler
20
ENGLISH
Screen Share
Allows the screen of a user's device such as a mobile or PC Windows to be shared with a display using a wireless
connection such as WiDi or Miracast.
To use Screen Share
When the Screen Share app is running, the wireless connection such as WiDi or Miracast is automatically set to
ON and the display is automatically changed to the connection ready mode. In this state, you can use Screen
Share by turning on the wireless connection on the device and selecting the display to establish a connection
between the device and the display.
NOTE
Configuring WiDi (Wireless Display)
WiDi, which is short for Wireless Display, is a system that wirelessly transmits video and sound files from a
laptop that supports Intel WiDi to the display.
This is available only in certain input modes (Composite/Component/RGB/HDMI).
Other than these modes, LG Signage cannot be detected by your PC.
1
Connect your laptop to an AP. (This feature can be used without an AP, but it is recommended that you
connect to it for optimal performance.)
Run the Intel WiDi ( ) program on your laptop.
2
Any nearby LG Signages supporting WiDi are detected. In the list of detected displays, select a Signage to
connect to and then, click Connect.
Enter the 8-digit PIN number (a) displayed on the Signage in the input field of your laptop (b) and click
Continue.

[Intel Notebook] Connection Request

Enter the PIN below.
PIN********
a
********
b

Time remaining: 92 seconds
Cancel
Signage screen
3
Laptop screen
The laptop screen appears in the Signage screen within 10 seconds. The wireless environment may affect
the screen from displaying.
If the connection is poor, the Intel WiDi connection may be lost.
••LG Signage does not need to be registered.
••In the sound settings of the Signage, set Digital Sound Output to PCM.
••For more information on how to use Intel WiDi, visit http://intel.com/go/widi.
••This works normally with WiDi 3.5 or later versions.
21
Listen Mode
You can select between On and Off.
If it is set to On, even when the app is not running,
you can turn on a wireless connection feature such
as WiDi or Miracast and select a display to connect
the device and display. Then, Screen Share will be
available for use.
NOTE
••If the Screen Share app has been deleted from
the HOME screen, Screen Share cannot be used
even if Listen Mode is set to On.
To set the transfer speed
Transfer Speed
Transfer speed can be set to Fast or Normal. When
Screen Share is running, this option adjusts the
time difference of the image output between
the device and the display. Adjusting the transfer
speed can repair any interruptions in displays
when mirroring is used.
ENGLISH
To select connection mode
22
ENGLISH
PICTURE ID Settings
NOTE
PICTURE ID is used to change the settings of a
specific set (display) using a single IR receiver for
multi-vision. Communication is possible between
a monitor with an IR receiver and other monitors
using RS-232C cables. Each monitor is identified
by a Set ID. If you assign the PICTURE ID using
the remote control, only displays with matching
PICTURE ID and Set ID can be controlled remotely.
AUDIO
(RGB/DVI)
RS-232C OUT
RS-232C OUT
RS-232C OUT
RS-232C IN
RS-232C IN
RS-232C IN
REMOTE
CONTROL IN
1
Assign the Set ID to the installed monitors as
shown below.
IR & Light Sensor
RS-232C cables
PICTURE ID ON [2]
2
3
Press the red ON button on the remote control
to assign the PICTURE ID.
Assign the Set ID to the selection of your
choice.
••A set with a different Set ID from the PICTURE
ID cannot be controlled by IR signals.
••If PICTURE ID is set to 2, only the upper
right monitor, which has a Set ID of 2, can be
controlled by IR signals.
••If you press the green OFF button for PICTURE
ID, the PICTURE IDs for all monitors are turned
off. If you then press any button on the remote
control, all monitors can be controlled by IR
signals regardless of Set ID.
23
ENGLISH
IR CODES
All models do not support the HDMI/USB function.
Some key codes may not be supported depending on the model.
Code (Hex)
Function
08
Remarks
Remote control button
C4
C5
ON
Remote control button
OFF
Remote control button
95
Energy Saving
Remote control button
0B
INPUT
Remote control button
10
Number Key 0
Remote control button
11
Number Key 1
Remote control button
12
Number Key 2
Remote control button
13
Number Key 3
Remote control button
14
Number Key 4
Remote control button
15
Number Key 5
Remote control button
16
Number Key 6
Remote control button
17
Number Key 7
Remote control button
18
Number Key 8
Remote control button
19
Number Key 9
Remote control button
02
Volume
Remote control button
03
Volume
Remote control button
E0
E1
(Page Up)
Remote control button
(Page Down)
Remote control button
DC
3D
Remote control button
32
1/a/A
Remote control button
2F
CLEAR
Remote control button
7E
Remote control button
79
ARC(MARK) (Aspect Ratio)
Remote control button
4D
PSM (Picture Mode)
Remote control button
09
MUTE
Remote control button
43
SETTINGS (Menu)
Remote control button
99
Auto Config.
Remote control button
40
Up
Remote control button
41
Down
Remote control button
06
Right
Remote control button
07
Left
Remote control button
44
OK
Remote control button
28
BACK
Remote control button
24
ENGLISH
Code (Hex)
Function
Remarks
7B
TILE
Remote control button
5B
EXIT
Remote control button
72
ID ON (RED)
Remote control button
71
ID OFF (GREEN)
Remote control button
63
YELLOW
Remote control Button
61
BLUE
Remote control button
B1
Remote control button
B0
Remote control button
BA
Remote control button
8F
Remote control button
8E
Remote control button
5F
W.BAL
Remote control button
3F
S.MENU
Remote control button
7C
HOME
Remote control button
* Some key codes are not supported depending on the model.
25
Use this method to connect several products to a single PC. You can control several products at a time by
connecting them to a single PC.
In the Option menu, the Set ID must be between 1 and 1000 without being duplicated.
Connecting the Cable
Connect the RS-232C cable as shown in the picture.
The RS-232C protocol is used for communication between the PC and product. You can turn the product on or
off, select an input source or adjust the OSD menu from your PC.
Monitor 4
RS-232C
OUT
RS-232C
IN
Monitor 3
RS-232C
OUT
Monitor 2
RS-232C
IN
RS-232C
OUT
RS-232C
IN
RS-232C
OUT
RS-232C
IN
RS-232C Gender
4P Cable
(not included)
Communication Parameter
Baud Rate: 9600 BPS
Data Length: 8 bit
Parity Bit: None
Stop Bit: 1 bit
Flow Control: None
Communication Code: ASCII code
PC
Monitor 1
RS-232C Cable
(not included)
NOTE
••When using three-wire connections (nonstandard), an IR daisy chain cannot be used.
••Be sure to only use the provided gender to
connect properly.
••When monitors connected via Daisy Chain (that
controls multiple monitors) are turned off and
on successively, some monitors may not turn
on. In this case, you can turn those monitors on
by pressing the MONITOR ON button, not the
POWER button.
(POWER)
MONITOR ON
ENGLISH
TO CONTROL MULTIPLE PRODUCTS
26
ENGLISH
Command Reference List
COMMAND
1
DATA
(Hexadecimal)
2
01
Power
k
a
00 to 01
02
Select input
x
b
See Select Input
03
Aspect Ratio
k
c
See Aspect Ratio
04
Energy Saving
j
q
See Energy Saving
05
Picture Mode
d
x
See Picture Mode
06
Contrast
k
g
00 to 64
07
Brightness
k
h
00 to 64
08
Sharpness
k
k
00 to 32
09
Color
k
i
00 to 64
10
Tint
k
j
00 to 64
11
Color temperature
x
u
00 to 64
12
Balance
k
t
00 to 64
13
Sound Mode
d
y
See Sound Mode
14
Mute
k
e
00 to 01
15
Volume Control
k
f
00 to 64
16
Time 1 (year/month/day)
f
a
See Time 1
17
Time 2 (hour/minute/second)
f
x
See Time 2
18
Off time schedule
f
c
00 to 01
19
On Time Schedule
f
b
00 to 01
20
Off Timer (Repeat/Time)
f
e
See Off Timer
21
On Timer (Repeat/Time)
f
d
See On Timer
22
On Timer Input
f
u
Refer to On Timer Input.
23
No Signal Power Off (15Min)
f
g
00 to 01
24
Auto Power Off (4 Hours)
m
n
00 to 01
25
Language
f
i
See Language
26
Reset
f
k
00, 02
27
Current Temperature
d
n
FF
28
Key
m
c
See Key
29
Time Elapsed
d
l
FF
30
Product Serial Number
f
y
FF
31
Software Version
f
z
FF
32
White Balance Red Gain
j
m
00 to FE
33
White Balance Green Gain
j
n
00 to FE
34
White Balance Blue Gain
j
o
00 to FE
27
DATA
(Hexadecimal)
2
35
White Balance Red Offset
s
x
00 to 7F
36
White Balance Green Offset
s
y
00 to 7F
37
White Balance Blue Offset
s
z
00 to 7F
38
Backlight
m
g
00 to 64
39
Screen off
k
d
00 to 01
40
Tile Mode
d
d
00 to FF
41
Check Tile Mode
d
z
FF
42
Tile ID
d
i
See Tile ID
43
Natural Mode
d
j
00 to 01
44
DPM Select
f
j
00 to 07
45
Remote Control/Local Key Lock
k
m
00 to 01
46
Power On Delay
f
h
00 to FA
47
Fail Over Select
m
i
00 to 02
48
Fail Over Input Select
m
j
See Fail Over Input Select
49
IR Operation
t
p
00 to 02
50
Local Key Operation
t
o
00 to 02
51
Check the status
s
v
See Check the status
52
Check Screen
t
z
00 to 01
53
Speakers
d
v
00 to 01
54
Daylight Saving Time
s
d
Refer to ‘Daylight Saving Time’
55
PM Mode
s
n, 0c
56
ISM Method
j
p
57
Network Settings
s
n, 80(81)(82)
58
Auto-adjustment
j
u
01
59
H Position
f
q
00 to 64
60
V Position
f
r
00 to 64
61
H Size
f
s
00 to 64
62
Power On Status
t
r
00 to 02
63
Wake On LAN
f
w
00 to 01
64
Intelligent Auto
t
i
00 to 01
65
OSD Portrait Mode
t
h
00 to 02
66
Reset to Initial Settings
t
n
00 to 01
67
Time Sync
s
n, 16
00 to 01
68
Contents Sync
t
g
00 to 01
00 to 03
See ISM Method
See Network Settings
* Note: While playing media files from a USB device or external/internal memory, all commands except for the
Power (k a), Volume (k f ), Mute (k e), and Key (m c) commands do not work and are processed as NG.
Some commands may not be supported depending on the model.
ENGLISH
COMMAND
1
28
ENGLISH
Transmission/Reception Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command1]: identifies between the factory setting and the user setting modes.
* [Command2]: controls monitor sets.
* [Set ID]: Used for selecting a set you want to control. A unique Set ID can be assigned to each set ranging
from 1 to 1000(01H~3E8H) under Settings in the OSD menu.
Selecting '00H' for Set ID allows the simultaneous control of all connected monitors.
(The maximum value may differ depending on the model.)
* [Data]: Transmits command data.
Data count may increase depending on the command.
* [Cr]: Carriage Return. Corresponds to '0x0D' in ASCII code.
* [ ]: White Space. Corresponds to '0x20' in ASCII code.
Acknowledgement
[Command2][ ][Set ID][ ][OK/NG][Data][x]
* The Product transmits ACK (acknowledgement) based on this format when receiving normal data. At this
time, if the data is FF, it indicates the present status data. If the data is in data write mode, it returns the data of
the PC computer.
* If a command is sent with Set ID '00' (=0x00), the data is reflected to all monitor sets and each monitor set
does not send an acknowledgement (ACK).
* If the data value 'FF' is sent in control mode via RS-232C, the current setting value of a function can be
checked (only for some functions).
*Some commands are not supported depending on the model.
29
01. Power (Command: k a)
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data][x]
*The acknowledgement signal is returned properly only when
the monitor is fully powered on.
* There may be a delay between the transmission and
acknowledgement signals.
02. Select Input (Command: x b)
Selects an input signal.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data
40: COMPONENT
60: RGB
70: DVI-D (PC)
80: DVI-D (DTV)
90: HDMI1 (DTV)
A0: HDMI1 (PC)
91: HDMI2/OPS (DTV)
A1: HDMI2/OPS (PC)
C0: DISPLAYPORT (DTV)
D0: DISPLAYPORT (PC)
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
04. Energy Saving (Command: j q)
Sets the Energy Saving.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: Minimum
02: Medium
03: Maximum
04: Automatic
05: Screen off
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
** This may not be supported depending on the model.
05. Picture Mode (Command: d x)
Selects a picture mode.
Transmission
[d][x][ ][Set ID][ ][Data][Cr]
Data
00: Vivid
01: Standard
02: Cinema
03: Sports
04: Game
05: Expert 1
06: Expert 2
08: APS
09: Photos
11: Calibration
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data][x]
* Some input signals may not be supported depending on the
model.
03. Aspect Ratio (Command: k c)
Adjusts the aspect ratio.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data
01: 4:3
02: 16:9
04: Zoom
06: Set by Program
09: Just Scan (720p or higher)
10 to 1F: Cinema Zoom 1 to 16
* Available data types differ depending on the input signal. For
more information, see the aspect ratio section of the owner’s
manual.
* The aspect ratio may differ depending on the model's input
configuration.
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
Adjusts the screen contrast.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Contrast 0 to 100
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
Controls the power on/off of the set.
30
ENGLISH
07. Brightness (Command: k h)
Adjusts the screen brightness.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
10. Tint (Command: k j)
Adjusts the screen tint.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Brightness 0 to 100
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
Data
00 to 64: Tint red 50 to green 50
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
08. Sharpness (Command: k k)
Adjusts the screen sharpness.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data
00 to 32: Sharpness 0 to 50
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
09. Color (Command: k i)
Adjusts the screen color.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Color 0 to 100
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
11. Color Temperature (Command: x u)
Adjusts the screen color temperature.
Transmission
[x][u][ ][Set ID][ ][Data][Cr]
Data
00 to 64: warm 50 to cool 50
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
12. Balance (Command: k t)
Adjusts the sound balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
00 to 64: left 50 to right 50
Acknowledgement
[t][ ][Set ID][ ][OK/NG][Data][x]
31
Data
01: Standard
02: Music
03: Cinema
04: Sports
05. Game
07: News
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
14. Mute (Command: k e)
Mutes/unmutes the sound.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data
00: Mute
01: Unmute
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
15. Volume Control (Command: k f)
Adjusts the playback volume.
Transmission
[k][f ][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Volume 0 to 100
Acknowledgement
[f ][ ][Set ID][ ][OK/NG][Data][x]
16. Time 1 (year/month/day) (Command: f a)
Sets the values of the Time 1 (year/month/day), or sets the Auto
time.
Transmission
1. [f ][a][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
2. [f ][a][ ][Set ID][ ][0][0][ ][Data1][ ][Cr]
1. Setting the Time 1 (year/month/day)
Data1
04~1B: year 2014 to 2037
Data2
01 to 0C: January to December
Data3
01 to 1F: 1st to 31st
* Enter "fa [Set ID] ff" to view the Time 1 (year/month/day)
settings.
2. Setting the Auto time
Data1
00: Auto
01: Manual
* To view the set value of the Auto time, enter “fa [Set ID] 00 ff”.
Acknowledgement
1. [a][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
2. [a][ ][Set ID][ ][OK/NG][0][0][Data1][x]
17. Time 2 (hour/minute/second) (Command: f x)
Adjusts the Time 2 (hour/minute/second) value.
Transmission
[f ][x][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
00 to 17: 00 to 23 hours
Data2
00 to 3B: 00 to 59 minutes
Data3
00 to 3B: 00 to 59 seconds
* Enter “fx [Set ID] ff” to view the Time 2 (hour/minute/second)
settings.
** This function is only available when Time 1 (year/month/
day) is set.
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
18. Off Time Schedule (Command: f c)
Enables/disables the Off Time Schedule.
Transmission
[f ][c][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
19. On Time Schedule (Command: f b)
Enables/disables the On Time schedule.
Transmission
[f ][b][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
13. Sound mode (Command: d y)
Selects a sound mode.
Transmission
[d][y][ ][Set ID][ ][Data][Cr]
32
ENGLISH
20. Off Timer (Repeat/Time) (Command: f e)
Configures Off Timer (Repeat/Time) settings.
Transmission
[f ][e][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
21. On timer (Repeat/Time) (Command: f d)
Configures On Timer (Repeat/Time) settings.
Transmission
[f ][d][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
1. f1h to f7h (reading data)
F1: reads the 1st Off Timer data
F2: reads the 2nd Off Timer data
F3: reads the 3rd Off Timer data
F4: reads the 4th Off Timer data
F5: reads the 5th Off Timer data
F6: reads the 6th Off Timer data
F7: reads the 7th Off Timer data
2. e1h-e7h (delete one index), e0h (delete all indexes)
E0: erases all Off Timer settings
E1: erases the 1st Off Timer setting
E2: erases the 2nd Off Timer setting
E3: erases the 3rd Off Timer setting
E4: erases the 4th Off Timer setting
E5: erases the 5th Off Timer setting
E6: erases the 6th Off Timer setting
E7: erases the 7th Off Timer setting
3. 01h to 0Ch (sets the day of the week for the Off Timer)
01: Once
02. Daily
03: Mon - Fri
04: Mon - Sat
05: Sat - Sun
06. Every Sunday
07. Every Monday
08. Every Tuesday
09. Every Wednesday
0A. Every Thursday
0B. Every Friday
0C. Every Saturday
Data2
00 to 17: 00 to 23 hours
Data3
00 to 3B: 00 to 59 minutes
* To read or delete the Off Time Schedule list, [Data2][Data3]
must be set to FFH.
Example 1: fe 01 f1 ff ff – reads the first index data in Off Timer.
Example 2: fe 01 e1 ff ff - deletes the first index data from Off
Timer.
Example 3: fe 01 04 02 03 - sets Off Timer to 02:03 from Monday
to Saturday.
* This function is only available when Time 1 (year/month/day)
and Time 2 (hour/minute/second) are set.
Data1
1. f1h to f7h (reading data)
F1: reads the 1st On Timer data
F2: reads the 2nd On Timer data
F3: reads the 3rd On Timer data
F4: reads the 4th On Timer data
F5: reads the 5th On Timer data
F6: reads the 6th On Timer data
F7: reads the 7th On Timer data
2. e1h-e7h (delete one index), e0h (delete all indexes)
E0: erases all On Timer settings
E1: erases the 1st On Timer setting
E2: erases the 2nd On Timer setting
E3: erases the 3rd On Timer setting
E4: erases the 4th On Timer setting
E5: erases the 5th On Timer setting
E6: erases the 6th On Timer setting
E7: erases the 7th On Timer setting
3. 01h to 0Ch (sets the day of the week for the On Timer)
01: Once
02. Daily
03: Mon - Fri
04: Mon - Sat
05: Sat - Sun
06. Every Sunday
07. Every Monday
08. Every Tuesday
09. Every Wednesday
0A. Every Thursday
0B. Every Friday
0C. Every Saturday
Data2
00 to 17: 00 to 23 hours
Data3
00 to 3B: 00 to 59 minutes
* To read or delete an On Time schedule list, [Data2][Data3]
must be set to FF.
Example 1: fd 01 f1 ff ff - reads the first index data from On
Timer.
Example 2: fd 01 e1 ff ff - deletes the first index data from On
Timer.
Example 3: fd 01 04 02 03 - sets On Timer to 02:03 from Monday
to Saturday.
* This function is only available when Time 1 (year/month/day)
and Time 2 (hour/minute/second) are set.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
33
Data (Add schedule)
40: COMPONENT
60: RGB
70: DVI-D(PC)
A0: HDMI1(PC)
A1: HDMI2/OPS(PC)
D0: DISPLAYPORT(PC)
Data1 (Read schedule)
1. f1h to f7h (Read data)
F1: Select the 1st schedule input
F2: Select the 2nd schedule input
F3: Select the 3rd schedule input
F4: Select the 4th schedule input
F5: Select the 5th schedule input
F6: Select the 6th schedule input
F7: Select the 7th schedule input
Data2 (Read schedule)
FF
* To read the schedule input, enter FF for [Data2].
If no schedule is available for [Data1] when attempting to
read the schedule data, the text ‘NG’ will be displayed and the
operation will fail.
(Example 1: fu 01 90 - Move each schedule input down one row
and save the 1st schedule input in HDMI mode.)
(Example 2: fu 01 f1 ff - Read the 1st schedule input.)
* This function is supported only when 1 (Year/Month/Day), 2
(Hour/Minute/Second), On Time (Repeat Mode/Time) are set.
** It may not be supported depending on the model.
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
[u][ ][Set ID][ ][OK/NG][Data1][Data2][x]
23. No Signal Power Off (15Min) (Command: f g)
Sets the monitor to enter Automatic Standby mode if there is
no signal for 15 minutes.
Transmission
[f ][g][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
24. Auto Power Off (4 Hours) (Command: m n)
Sets the monitor to enter Auto Power Off after 4 hours.
Transmission
[m][n][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: 4 hours
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
25. Language (Command: f i)
Sets the OSD language.
Transmission
[f ][i][ ][Set ID][ ][Data][Cr]
Data
00: Czech
01: Danish
02: German
03: English
04: Spanish (Europe)
05: Greek
06: French
07: Italian
08: Dutch
09: Norwegian
0A: Portuguese
0B: Portuguese (Brazil)
0C: Russian
0D: Finnish
0E: Swedish
0F: Korean
10: Chinese (Mandarin)
11: Japanese
12: Chinese (Cantonese)
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
22. On Timer Input (Command: f u)
Select an external input for the current On Time setting and add
a new schedule.
Transmission
[f ][u][ ][Set ID][ ][Data1][Cr]
[f ][u][ ][Set ID][ ][Data1][][Data2][Cr]
34
ENGLISH
26. Reset (Command: f k)
Performs the Picture and Factory Reset functions.
Transmission
[f ][k][ ][Set ID][ ][Data][Cr]
Data
00: Picture Reset
02: Initial Settings (factory reset)
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
27. Current temperature (Command: d n)
Checks the inside temperature.
Transmission
[d][n][ ][Set ID][ ][Data][Cr]
Data FF: Check the status
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
* Temperature is displayed as a hexadecimal value.
28. Key (Command: m c)
Sends a key code for the IR remote control.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
DataIR_KEY_CODE
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
For key codes, see IR Codes.
* Some key codes are not supported depending on the model.
29. Time Elapsed (Command: d l)
Checks the elapsed time.
Transmission
[d][l][ ][Set ID][ ][Data][Cr]
Data
FF: Read status
Acknowledgement
[l][ ][Set ID][ ][OK/NG][Data][x]
* The data received is shown as a hexadecimal value.
30. Product serial number (Command: f y)
Checks the serial number of the product.
Transmission
[f ][y][ ][Set ID][ ][Data][Cr]
Data
FF: Check product serial number
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
* Data is in ASCII code.
31. Software Version (Command: f z)
Checks the software version of the product.
Transmission
[f ][z][ ][Set ID][ ][Data][Cr]
Data
FF: Check software version
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
35
Data
00 to FE: Red Gain 0 to 254
FF: checks the red gain value
Acknowledgement
[m][ ][Set ID][ ][OK/NG][Data][x]
33. White Balance Green Gain (Command: j n)
Adjusts the white balance green gain value.
Transmission
[j][n][ ][Set ID][ ][Data][Cr]
Data
00 to FE: Green Gain 0 to 254
FF: checks the green gain value
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
34. White Balance Blue Gain (Command: j o)
Adjusts the white balance blue gain value.
Transmission
[j][o][ ][Set ID][ ][Data][Cr]
Data
00 to FE: Blue Gain 0 to 254
FF: checks the blue gain value
Acknowledgement
[o][ ][Set ID][ ][OK/NG][Data][x]
35. White Balance Red Offset (Command: s x)
Adjusts the white balance red offset value.
Transmission
[s][x][ ][Set ID][ ][Data][Cr]
Data
00 to 7F: Red Offset 0 to 127
FF: checks the red offset value
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data][x]
36. White Balance Green Offset (Command: s y)
Adjusts the white balance green offset value.
Transmission
[s][y][ ][Set ID][ ][Data][Cr]
Data
00 to 7F: Green Offset 0 to 127
FF: checks the green offset value
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
37. White Balance Blue Offset (Command: s z)
Adjusts the white balance blue offset value.
Transmission
[s][z][ ][Set ID][ ][Data][Cr]
Data
00 to 7F: Blue Offset 0 to 127
FF: checks the blue offset value
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
32. White balance red gain (Command: j m)
Adjusts the white balance red gain value.
Transmission
[j][m][ ][Set ID][ ][Data][Cr]
36
ENGLISH
38. Backlight (Command: m g)
Adjusts the backlight brightness.
Transmission
[m][g][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Backlight 0 to 100
Acknowledgement
[g][][set ID][][OK/NG][Data][x]
41. Check Tile Mode (Command: d z)
Checks the tile mode.
Transmission
[d][z][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
Data1
Data2
Data3
39. Screen Off (Command: k d)
Turns the screen on or off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data
00: turns the screen on
01: turns the screen off
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
FF: checks the tile mode
00: tile mode off
01: tile mode on
00 to 0F: tile column
00 to 0F: tile row
42. Tile ID (Command: d i)
Sets the tile ID value of the product.
Transmission
[d][i][ ][Set ID][ ][Data][Cr]
Data
01 to E1: Tile ID 1 to 225**
FF: checks the tile ID
** The data value cannot exceed the value of row x column.
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
* When a data value that exceeds the value of row x column
is entered (except 0xFF),
ACK becomes NG.
40. Tile Mode (Command: d d)
Sets the Tile Mode and sets values for the tile rows and
columns.
Transmission
[d][d][ ][Set ID][ ][Data][Cr]
Data
00 to FF: The first byte - tile column
The second byte - tile row
* 00, 01, 10, and 11 mean that the tile mode is off
** The maximum value may differ depending on the model.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
43. Natural Mode (in Tile mode) (Command: d j)
When displaying the image naturally, the part of the image
that would normally be displayed in the gap between the
monitors is omitted.
Transmission
[d][j][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
37
Data
00: Off
01: 5 seconds
02: 10 seconds
03: 15 seconds
04: 1 minutes
05: 3 minutes
06: 5 minutes
07: 10 minutes
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
45. Remote Control/Local Key Lock (Command: k m)
Adjusts the remote control/local key (front) lock.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 00: Off (Lock Off )
01: On (Lock On)
* When the monitor is turned off, the power key works even
in On (01) mode.
Acknowledgement
[m][ ][Set ID][ ][OK/NG][Data][x]
47. Fail Over Select (Command: m i)
Selects an input mode for auto switch.
Transmission
[m][i][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: Auto
02: Manual
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
48. Fail Over Input Select (Command: m j)
Selects an input source for auto switch.
* This command is only available when the Fail Over (auto)
mode is set to Custom.
Transmission
[m][j][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][ ]
[Data4]...[ ][DataN][Cr]
Data 1 to N-1 (Input priority: 1 to N-1)
40: COMPONENT
60: RGB
70: DVI-D
90: HDMI1
91: HDMI2/OPS
C0: DISPLAYPORT
Data N: E0: INTERNAL USB
E1: USB
E2: SD CARD
Acknowledgement
[j][ ][SetID][ ][OK/NG][Data1][Data2][Data3][Data4]
...[DataN] [x]
46. Power On Delay (Command: f h)
Sets the schedule delay when the power turns on. (unit:
seconds).
Transmission
[f ][h][ ][Set ID][ ][Data][Cr]
Data
00 to FA: min. 0 to maximum 250 (seconds)
* The maximum value may differ depending on the model.
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x
Data 1 to N-1 (Input priority: 1 to N-1)
40: COMPONENT
60: RGB
70: DVI-D
90: HDMI1
91: HDMI2/OPS
C0: DISPLAYPORT
Data N: E0: INTERNAL USB
E1: USB
E2: SD CARD
* Some input signals may not be available with certain
models.
**The data number (N) may vary depending on the model.
(The data number depends on the number of supported
input signals.)
*** Only the value of E0, E1, or E2 is acceptable for the last
data.
ENGLISH
44. DPM Select (Command: f j)
To set the DPM (Display Power Management) function.
Transmission
[f ][j][ ][Set ID][ ][Data][Cr]
38
ENGLISH
49. IR Operation (Command: t p)
Configures the IR operation settings of the product.
Transmission
[t][p][ ][Set ID][ ][Data][Cr]
Data
00: locks off all of the keys
01: locks on all of the keys except the Power key
02: locks on all of the keys
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data][x]
* When the monitor is turned off, the power key works even
in the locks on all of the keys (02) mode.
50. Local Key Operation (Command: t o)
Configures the local key operation settings of the product.
Transmission
[t][o][ ][Set ID][ ][Data][Cr]
Data
00: locks off all of the keys
01: locks on all of the keys except the Power key
02: locks on all of the keys
52. Check Screen (Command: t z)
Sets Check Screen.
Transmission
[t][z][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
53. Speaker (Command: d v)
Sets the speaker function.
Transmission
[d][v][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[v][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement
[o][ ][Set ID][ ][OK/NG][Data][x]
* When the monitor is turned off, the power key works even
in the locks on all of the keys (02) mode.
54. Daylight Saving Time (Command: s d)
51. Status (Command: s v)
Checks the current signal status of the product.
Transmission
[s][v][ ][Set ID][ ][Data][ ][FF][Cr]
Data 02: checks whether there is a signal or not
03: check the PM mode.
10: RGB sensing OK/NG (Check Screen)
Acknowledgement
[v][ ][Set ID][ ][OK/NG][Data][Data1][x]
Data:
Data1
02 (when a signal is found)
00: no signal
01: there is a signal
Data:
Data1
03 (when checking the PM mode)
00: The PM mode is set to Screen On
01: The PM mode is set to Screen Off
02: The PM mode is set to Screen Off Always
Data: 10 (Check Screen)
Data1 00: Check Screen result NG
07: Check Screen result OK
* Sets to NG when Check Screen is set to Off or not supported.
To set theDaylight Saving Time function.
Transmission
[s][d][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][ ][Data4]
[ ][Data5][Cr]
Data
00: Off (Data2~5: FFH)
01: Start Time
02: End Time
Data2 01~0C: January to December
Data3 01~06: 1 ~ 6th week
* The maximum number of [Data3] differs depending on
Date.
Data4 00~06 ( Sun. ~ Sat. )
Data5 00~17: 00 ~ 23 hours
* To read the Start Time/End Time, enter FFH for
[Data2]~[Data5].
(ex1: sd 01 01 ff ff ff ff - To check the Start Time
ex2: sd 01 02 ff ff ff ff - To check the End Time)
* This function is supported only when 1 (Year/Month/ Day)
and 2 (Hour/Minute/Second) are set.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][Data4]
[Data5][x]
** It may not be supported depending on the model.
39
Data
00: Sets the Power Off mode.
01: Sets the Sustain Aspect Ratio mode.
02: Sets the Screen Off mode.
03: Sets the Screen Off Always mode.
Acknowledgement
[n][ ][Set ID][ ][OK/NG][0c][Data][x]
* It may not be supported depending on the model.
56. ISM Method (Command: j p)
Selects the ISM Method option.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data
04: White Wash
08: Normal
20: Color Wash
90: User Image
** The jp command works when Timer is set to Immediately.
Acknowledgement
[p][ ][Set ID][ ][OK/NG][Data][x]
* If Data1 is 81,
Data2 : DNS address
FF: Views the temporary DNS address.
* If Data1 is 82,
Data2 80: Applies the temporarily saved IP mode (Auto/
Manual), subnet mask, and gateway.
81: Applies the temporary DNS address
FF: Information on the current network (IP, subnet
gateway, DNS)
*** Examples of settings
1. Auto: sn 01 80 00
2. Manual: sn 01 80 01 010177223241 255255254000
010177222001 (IP: 10.177.223.241, subnet:
255.255.254.0,
gateway: 10.177.222.1)
3. Network read: sn 01 80 ff
4. DNS setting: sn
01 81 156147035018
(DNS: 156.147.35.18)
**** Each IP address contains 12 decimal digits .
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data1][Data][x]
* It may not be supported depending on the model.
** This feature is available only for wired networks.
* It may not be supported depending on the model.
58. Auto-adjustment (Command: j u)
Automatically corrects the position and shaking of the picture.
(Works only in RGB-PC input mode.)
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data
01: Execution
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
* It may not be supported depending on the model.
Network Settings (Command: s n, 80 or 81 or 82)
Configures network and DNS settings.
Transmission
[s][n][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ]
[Data5][Cr]
80: Configures/views the temporary IP mode
(Auto/Manual), subnet mask, and gateway.
81: Configures/views the temporary DNS address.
82: Saves temporary settings and views
information about the current network.
* If Data1 is 80,
Data2 00: Auto
01: Manual
FF: Views the temporary IP mode (Auto/Manual),
subnet mask, and gateway.
Data1
** If Data2 is 01 (Manual),
Data3 : Manual IP address
Data4 : Subnet mask address
Data5 : Gateway address
59. H Position (Command: f q)
Adjusts the horizontal position of the screen. This feature only
works when the Tile Mode is set to Off.
* The operational range varies depending on the RGB input
resolution. (Works only in RGB-PC input mode.)
Transmission
[f ][q][ ][Set ID][ ][Data][Cr]
Data
00-64: Min -50 (Left) to Max 50 (Right)
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
* It may not be supported depending on the model.
ENGLISH
55. PM Mode (Command: s n, 0c)
Selects the desired PM mode option.
Transmission
[s][n][ ][Set ID][ ][0c][ ][Data][Cr]
40
ENGLISH
60. V Position (Command: f r)
Adjusts the vertical position of the screen. This feature only
works when the Tile Mode is set to Off.
* The operational range varies depending on the RGB input
resolution. (Works only in RGB-PC input mode.)
Transmission
[f ][r][ ][Set ID][ ][Data][Cr]
Data
00-64: Min -50 (Down) to Max 50 (Up)
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
63. Wake On LAN (Command: f w)
Selects the desired Wake On LAN option.
Transmission
[f ][w][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[w][ ][Set ID][ ][OK/NG][Data][x]
* It may not be supported depending on the model.
61. H Size (Command: f s)
Adjusts the horizontal size of the screen. This feature only works
when the Tile Mode is set to Off.
* The operational range varies depending on the RGB input
resolution. (Works only in RGB-PC input mode.)
Transmission
[f ][s][ ][Set ID][ ][Data][Cr]
64. Intelligent Auto (Command: t i)
Selects the desired Intelligent Auto option.
Transmission
[t][i][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
* It may not be supported depending on the model.
Data
00-64: Min -50 (Small) to Max 50 (Large)
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data][x]
* It may not be supported depending on the model.
62. Power On Status (Command: t r)
Selects the desired Power On status option.
Transmission
[t][r][ ][Set ID][ ][Data][Cr]
Data
00: LST (Stays in the previous status)
01: STD (Stays powered off )
02: PWR (Stays powered on)
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
65. OSD Portrait Mode (Command: t h)
Selects the desired Portrait mode option.
Transmission
[t][h][ ][Set ID][ ][Data] [Cr]
Data
00: Off
01: On
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data] [x]
* It may not be supported depending on the model.
41
Data
00: Disables the settings.
01: Enables the settings.
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data] [x]
* It may not be supported depending on the model.
67. Time Sync (Command: s n, 16)
Configures the Time Sync.
Transmission
[s][n][ ][Set ID][ ][1][6][ ][Data][Cr]
Data
00: Off
01: On
* This feature works in the Master mode.
** This feature does not work if the current time is not set.
Acknowledgement
[n][ ][Set ID][ ][OK/NG][ ][1][6][ ][Data][x]
* It may not be supported depending on the model.
68. Contents Sync (Command: t g)
Configures the Contents Sync.
Transmission
[t][g][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
* It may not be supported depending on the model.
ENGLISH
66. Reset to Initial Settings (Command: t n)
Enables/disables the Reset to Initial settings.
Transmission
[t][n][ ][Set ID][ ][Data] [Cr]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement