advertisement
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
1. Summarization
Summarize: Thank you for purchasing our ENERGY 7x12W RGBAW + UV (6-in-1) lighting. Please read these instructions carefully before begin and operate the fixtures according to these instructions to avoid any possible damages and accidents causes by misusage.
Products introduction: Energy 7x12W RGBW + UV (6in1) light uses casting aluminum housing, designed in a fashion of hydrodynamic form. Appearance shows. It adopts high power 6-in-1 LED, which refers to single LED is made of R,G,B,A,W,UV 6-IN-1 LED, And long life span, low consumption, good color mixing effect and high brightness are the most prominent features. Each kind of LED can be independently dimmed. The built-in program includes dimming, strobe, eotic, gradual change, fading and so on. It uses power switch, performs low weight and consumption, stable capability and long life. International standard DMX 512 signal is requested.
Packing list: 1x SquareLED ENERGY 7x12W RGBAW + UV (6-in-1) , 1x DMX signal cable,
1x Power cable, the User Manual, Warranty Card
2. Safety Instruction
Safety Notes
! Enquire the skilled people before any repair;
! Always make sure disconnect from the power source before setting up, serving and moving;.
! Avoid direct eye exposure to the fixture when it is on
Safety instruction
• Make sure the power supply voltage are consistent with this lights. Ensure the use of voltage is in the range of the request technical parameter.
• Before the installation, please check the light’s fasteners and mechanical structure have been received in good condition and appear no damage.
• This light is designed for indoor use; working temperature is lower than 40 degree.
• The fixtures maybe mounted in any position provided there is adequate room for ventilation.
Make sure there are no inflammable and explosive items (ornaments) in 0.5 meters away.
• Yellow / green cabling earthling safety; no flicker when the fixture is working on.
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
3. Main Function
» Input voltage: AC 100V-264V/47-63HZ
» Consume: 90W
» Lamp Type: 12W LED 6-in-1 R, G, B, A, W, UV (7PCS)
» Life span: 50000~100000hours
» PWM Dimmer: 1500HZ(16666 grades)
» Control Signal: DMX512
» Control mode: stand alone/ sound activated
» Channel: 12CH, 9CH, 7CH, 6CH, 5CH, 4CH
» Function Effect: dimmer, strobe, gradual change
» Touch buttons, automatic lock key
» Built-in temperature control measurement function, when LED work overheated, intelligent reduce LED output power, current power output can be viewed
» Cooling mode: Natural Convection
» built-in lithium battery, compatible with Swedish wireless DMX module
» Battery Capacity: 25.9V / 6.6Ah
» Charging time: 4 hours
» full light Duration: 3 hours
» Anti-electricity intension: 1.5KV
» Insulation Resistance: >2MΩ
» Size:287.3 x 270.1 x 166.0mm
» Net Weight: 5.2 kg
» Beam Angle: 15°, 25°, 45° Optional
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
4. Outside Size Picture
5. DMX Control Function
DMX Channels
4CH 5CH 6CH 7CH 9CH 12CH VALUE FUNCTION
CH1 CH1 CH1 CH1 0-255 Dimming all
CH1 CH1 CH2 CH2 CH2 0-255 Red
CH2 CH2 CH3 CH3 CH3 0-255 Green
CH3 CH3 CH4 CH4 CH4 0-255 Blue
CH2 CH4 CH5 CH5 CH5 0-255 Amber
CH4 CH3 CH5 CH6 CH6 CH6 0-255 White
CH4 CH6 CH7 CH7 CH7 0-255 UV
0-5 No strobe
CH8 CH8
6-20 Random burst strobe(slow to fast)
21-60 Normal strobe(slow to fast)
61-100 Electronic Sinewave(slow to fast)
101-140 Random Strobe(slow to fast)
141-180 Opening pulse(slow to fast)
181-220 Closing pulse(slow to fast)
221-255 Electronic Squarewave(slow to fast)
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
4CH 5CH 6CH 7CH 9CH 12CH VALUE FUNCTION
-
0-10 No effect
11-15 CT01
16-20 CT02
21-25 CT03
26-30 CT04
31-35 CT05
36-40 CT06
41-45 CT07
46-50 CT08
51-55 CT09
56-60 CT10
CH9
(CH9 prior to
61-65 AUTO 1 (R - G - B - A - W - UV - RG - RB - GB - AW - WUV - AUV)
66-70 AUTO 2 (Rˆ- R
ˇ
- Gˆ- G
ˇ
- Bˆ- B
ˇ
- Aˆ- A
ˇ
- Wˆ- W
ˇ
- UVˆ- UV
ˇ
)
71-75 AUTO 3 (Rˆ Gˆ- R
ˇ
G
ˇ
- Rˆ Bˆ- R
ˇ
B
ˇ
- Bˆ Gˆ- B
ˇ
G
ˇ
)
76-80 AUTO 4 (Rˆ- Gˆ- Bˆ- Wˆ- R
ˇ
- G
ˇ
- B
ˇ
- W
ˇ
)
81-85
AUTO 5 (Rainbow effect: B, BGˆ- BG,B
ˇ
B)
- G,G,GRˆ- GR,G
ˇ
- R,R,RBˆ- RB,Rˆ-
86-90 CHASE 1
91-95 CHASE 2
96-100 CHASE 3
101-110 Reserved
111-200
R:111-115, G:116-120, B:121-125, A:126-130, W:131-135, UV:136-
140, YELLOW:141-145, PINK:146-150, CYAN:151-155, ORANGE:156-160,
VIOLET:161-165, GOLDEN:166-170, 2700K:171-175, 3200K:176-180,
4000K:181-185, 5500K:186-190, 6500K:191-195, RGBW:196-200
201-255 Reserved
CH10 0-255 0-255(S),(speed of AUTO,fast to slow,when AUTO1-AUTO5 effective)
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
4CH 5CH 6CH 7CH 9CH 12CH VALUE FUNCTION
-
CH5 -
-
-
CH11
(RGB color mixing
CH9 CH12
0-10 No effect
11 Blue (Blue=full, Red+Green=0)(step)
12-50 Red=0, Green->up,Blue =full(proportional)
51 Light Blue (Red=0, Green=full, Blue =full)(step)
52-90 Red=0, Green=full, Blue->down(proportional)
91 Green (Red=0, Green=full, Blue =0)(step)
92-130 Red->up, Green=full, Blue=0(proportional)
131 Yellow (Red=full, Green=full, Blue=0)(step)
132-170 Red=full, Green->down, Blue=0(proportional)
171 Red(Red=full, Green=0, Blue=0(step)
172-210 Red=full, Green=0, Blue->up(proportional)
211 Magenta (Red=full, Green=0, Blue=full)(step)
212-250 Red -> down, Green=0, Blue=full(proportional)
251-255 Blue (Red=0, Green=0, Blue=full)(step)
0-10 Use the dimmer mode which menu had set up
11-20 Linear curve
21-30 Square law curve
31-40 Inverse square law curve
41-50 S-curve
51-60 Linear curve and smooth
61-70 Square law curve and smooth
71-80 Inverse square law curve and smooth
81-90 S-curve and smooth
91-255 Use the dimmer mode which menu had set up
5. Display Operation
» MENU: access the menu or return to a previous menu option
» UP: menu selection or parameter increments
» DOWN: menu selection or parameters decrease
» ENTER: select the current menu option
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
Menu Tree
Tab
ADDR(Address)
STAT(Static control)
SET(Set)
Level 1
001-512
R
G
B
A
W
UV
SHUT
Level 2
0-255*
0-255*
0-255*
0-255*
0-255*
0-255*
0-255*
0-255*
PRSC(Preset color)
NONE,R,G,B,A,W,UV,YELLOW,PINK,CYAN,ORANG
E,VIOLET,GOLDEN,2700K,3200K,4000K,5500K,6
500K,RGBW *
CAL(Calibration)
CHMD(Channel mode)
DIM(Dimming mode)
DISY(Display set)
LOCK(Key 2 minutes lock)
BAT(battery output)
SIGN(DMX signal selection)
R(Red)
G(Green)
B(Blue)
A
W
UV
USE
12CH
9CH
7CH
6CH
5CH
4CH
LIN(linear)/SQR(square law)/ISQR(inverse square law)/SCUR(S-curve)/LIN.(linear smooth)/SQR.(square law smooth)/ISQR.(inverse square law smooth)/SCUR.(S-curve smooth)
ON(Permanent on)
2MIN (2 minutes off)
YES/NO
HIGH(high)
MID
LOW
2.4G(wirelsee)/CABL(Cable)
Level 3
0-255
0-255
0-255
0-255
0-255
0-255
YES/NO
Level 4
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
Tab
CTST(Custom color set)
Level 1
WIRE(Wireless set)
CT01
AUTO(Auto)
PROG (Program)
INFO (Information)
SEND(Send)
CHS2
CHS3
CHS1 (Chase 1)
.
.
.
.
.
CT10
AT01
AT02
AT03
AT04
AT05
CHS1
.
.
.
.
.
.
.
CHS3 (Chase 3)
SOFT(Software version)
POW(Power reduction)
BAT
ST L (Setting load)
PR L (Program load)
VES/NO
Level 2
REST(reset)
KEY
R
A
W
G
B
UV
SC01 (Scene 1)
.
.
.
.
.
.
.
0-255*
0-255*
0-255*
0-255*
0-255*
RUN..*
RUN..*
RUN..*
.
.
.
.
SC20 (Scene 20)
Vx.x
100%/80%/50%
0-10
YES/NO
YES/NO
W
UV
SHUT
AUTO
B
A
G
R
ATSP
TIME
WAIT
USE
Level 3
YES/NO
0-255
0-255
0-255
0-255
0-255
0-255
Level 4
0-255
0-255
0-255
0-255
0-255
0-255
0-255
NONE,AT01-AT05
0-255(S)
0-255(S)
0-25.5(S)
YES/NO
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
7. Instruction
When enter to the “*” position displayed on the LED, the light will automatically set as master and send data to external.
Other fixtures can receive this data and will synchronously running without manually set as slave.
When power cycle it will jump to the “*” position and running again.
7.1 DMX ADDRESS SETTING
» 1) Press the (ENTER) button in (ADDR) menu, then enter to the DMX address setting.
» 2) Press the (UP/DOWN) button to select (1-512) numerical value.
» 3) Press the (ENTER) button to escape and save.
7.2 STATIC SETTING
» 1) Press the (ENTER)button in (STAT) menu, then enter to the static setting.
» 2) Press the (UP/DOWN) button to select
(RED) , (GREEN) , (BLUE) , (WHITE) ... (PRSC).
» 3) Press the (UP/DOWN) button to set up the (0-255) numerical value.
» 4) Press the (ENTER) button to escape and save.
7.3 COLOR CAST CALIBRATION SETTING
» 1) Press the (ENTER) button in (CAL) menu, then enter to the color cast calibration setting.
» 2) Press the (UP/DOWN) button to select (RED) , (GREEN) , (BLUE) , (UV)
» 3) Press the (UP/DOWN) button to set up the (0-255) numerical value.
» 4) On the (USE) interface, pressing (YES) button means valid, (NO) means invalid.
» 5) Press the (ENTER) button to escape and save.
» Illustrations: When pressing the (YES) button which means valid on the (USE) interface, the actual output value of RED (GREEN) BLUE...UV is output in accordance with the percentage which the color cast calibration value divides 255.
7.4 CHANNEL MODE SETTING
» 1) Press the (ENTER) button in (CHMD) menu, then enter to the channel mode setting.
» 2) Press the (UP/DOWN) button to select (12CH) , (9CH) , (7CH) , (6CH) , (5CH) , (4CH)
» 3) Press the (ENTER) button to escape and save.
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
7.5 DIMMING MODE SETTING
» 1) Press the (ENTER) button in (DIM) menu, then enter to the dimming mode setting.
» 2) Press the (UP/DOWN) button to select (LIN) (SQR) (ISQR) (SCUR) (LIN.) (SQR.) (ISQR.,and (SCUR.) .
» 3) Press the (ENTER) button to escape and save.
» Illustrations (When setting (LIN.) (SQR.) (ISQR.) and (SCUR.)in (DIM) menu, there will be added a little delay dimming effect for smooth..
» Dimming curve:
Linear curve:
Square law curve:
» Inverse Square law curve:
S-curve:
7.6 DISPLAY SETTING
» 1) Press the (ENTER) button in (DISY) menu, then enter to the display setting.
» 2) Press the (UP/DOWN) button to select (ON) , (2 MINITES OFF)
» 3) Press the (ENTER) button to escape and save.
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
7.7 AUTO LOCK KEY SETTING
» 1) Press the (ENTER) button in (LOCK) menu, then enter auto lock key setting.
» 2) Press the (UP/DOWN) button to select (YES), (NO)
» 3) Press the (ENTER) button to escape and save.
» Instructions: When set to [YES], it will lock automatically after two minutes to prevent accidental triggering flood flushing, and then press any key keep 10 seconds to unlock.
7.8 Battery output setting
» 1) Press the (ENTER) button in (BAT) menu, then enter to the Battery output setting.
» 2) Press the (UP/DOWN) button to select (HIGH) ,(MIDDLE), (LOW)
» 3) Press the (ENTER) button to escape and save.
7. 6.9 DMX signal selection setting
» 1) Press the (ENTER) button in (SIGN) menu, then enter to the DMX signal selection setting.
» 2) Press the (UP/DOWN) button to select (2.4G) , (CABLE)
» 3) Press the (ENTER) button to escape and save.
7. 6.10 Wireless set
» 1) Press the (ENTER) button in (WIRE) menu, then enter to the wireless set.
» 2) (RESET) the Analog process of press the button on again after wireless module off
» 3) (KEY) similar as the build-out kep
7. 6.11 CUSTOM COLOR SETTING
» 1) Press the (ENTER) button in (CTST) menu, then enter to the custom color setting.
» 2) Press the (UP/DOWN) select (CT01) … (CT10)
» 2) Press the (UP/DOWN) button to select (1-255) numerical value.
» 3) Press the (ENTER) button to escape and save.
7. 6.12 AUTO RUN, SELF-PROGRAM RUN
» 1) Press the (ENTER) button in (AUTO) menu, then enter to the auto run,self-program run.
» 2) Press the (UP/DOWN) button to select:
(AT01) … (AT05) , (AUTO SPEED) , (CHASE01)… (CHASE03)
» 3) Press the (ENTER) button to start running.
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
7.13 EDIT SELF-PROGRAM
» 1) Press the (ENTER) button in (PROG) menu, then enter to the edit self-program.
» 2) Press the (UP/DOWN) button to select (CHASE01) … (CHASE03)
» 3) Press the (ENTER) button for confirmation and enter to the next menu.
» 4) Press the (UP/DOWN) button to select (SCENE01) … (SCENE20)
» 5) Press the (ENTER) button for confirmation and enter to the next menu.
» 6) Then press the (UP/DOWN) button to select (RED) … (SHUT) , (TIME) , (WAIT) , (USE)
» 7) Press the (UP/DOWN) button to set up the parameter which are needed.
» 8) Press the (ENTER) button t o escape and save.
» Illustrations: When (USE) is set to be (NO) , or the parameter of (TIME) is 0, it will not run this scene.
When (WAIT) is set to be FADE time, the running process isas the following chart showing
7.14 CHECK THE LIGHTING INFORMATION
» 1) Press the (ENTER) button in (INFO) menu, then enter to the checking the lighting information.
» 2) (SOFT) button is for software version information.
» 3) (POW) button is for the current information of power reduction. It is 100% output in normal conditions, but
80% or 50% output in over temperature protection situation.
» 4) (BAT) Remaining battery power,from 0-10
7.15 LIGHTING SETTING PARAMETER RESET
» 1) Press the (ENTER) button in (ST L) menu, then enter to the lighting setting parameter reset.
» 2) Press the (UP/DOWN) button to select (YES) .
» 3) Press the (ENTER) button to escape and save.
» Illustrations: “ADDR” “CTST” and “PROG” are not reset, the others reset to the underlined value of the word.
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
7.16 (PROG) SELF-PROGRAMMING PARAMETER RESET
» 1) Press the (ENTER) button in) PR L (menu, then enter to the (PROG) self-programming parameter reset.
»
» 2) Press the (UP/DOWN) button to select (YES) .
» 3) Press the (ENTER) button to escape and save.
7.17 LIGHTING PARAMETER DOWNLOADING EACH OTHER VIA DMX CABLE
» 1) Press the (ENTER) button in (SEND) menu, then enter to sending parameter to other lightings.
» 2) Press the (UP/DOWN) button to select (YES) .
» 3) Press the (ENTER) button to confirm sending.
» Illustrations: 1) Please disconnect the connection of projector and DMX console before sending the parameter.
2) The information of (ADDR) , (CAL) can’t be sent, can’t be downloaded each other.
3) There will be an automatic reset of the other projectors after receiving parameter correctly.
8. Instruction for compatible Sweden DMX wireless module
1)
There are 4 modes: compatible Sweden receive mode(green indicator), compatible Sweden transmit mode(blue indicator), normal mode(yellow indicator),custom mode(red indicator)
2) After (RESET) and then press (KEY) to switch above modes, select needed mode and press
(KEY) one second to confirm and save it.
3) Under compatible Sweden DMX receive mode, press (KEY) 3 seconds to delete matching between light and transmitter.
4) Under compatible Sweden DMX transmit mode, press (KEY) to match receive mode, press 3 seconds will delete matched mode.
5) Working in normal mode, indicator has 7 colors for option, when light and transmitter indicator are in the same color, can receive and transmit data.
6) User-defined function is not available.
7)
Notice: compatible Sweden DMX mode in this lights has complete data for sending and receiving, but transmit function is not available here.
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
9. Operating Control Instruction
Master/Slave:
When the fixtures work in master mode it will send out the signal for the slave synchronous with it.
To avoid the host signal and DMX512 signals interfere with each other, should cut off the DMX512 signals. The signal lines are longer than 60 meters (20 lamps), should increase a signal amplifier.
10. XLR cable connecting
XLR cable: The standard way of connecting the XLR is: one end connects to the male plug, and the other end connects to the female. As bellow: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Noted: In order to avoid failures and interference signal transmission, we connect a resistance120Ω
(1/4W)at the end of the DMX connecting as below:
The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable
Manual | ENERGY 7x12W RGBAW + UV (6-in-1)
10. Connecting picture
Light connecting picture:
11. Trouble Shooting
Problem
The lightin g can’t be started normally
Checking Way
• Check the power connection is correct or not.
• Please detect the voltage.
• Power supply is damaged or incorrect connected. Call a qualified personnel to fix it.
• Connection of control board is not correct. Call a qualified personnel to fix it.
Out of console’s control
• Please check the DMX connector and the power connection is connected correctly or not. It means having signal if it shows twinkling of the decimal point which in the lower right corner of the screen when exiting the screen saver.
• Please check the DMX address setting of lighting is correct or not.
• Check (CHMD) setting is correct or not.
• Check (SIGN) setting is correct or not.
• Please check whether the DMX line is near to the high voltage wire or not. In that case, it will damage or interfere the DMX electric circuit.
The beam appears dim
,the brightness declines obviously
• Check whether the (CAL) is started or not and the set value is too small.
• Check whether the (POW) is in over temperature protection situation or not, if yes, please take measures for ventilation.
Noted: only professional persons can do as above!
Das Lichttechnikhaus Vertriebs GmbH
Rudolf-Diesel-Str. 3, D-89312 Günzburg
Telefon +49 (0) 82 21 207 98-0
Fax +49 (0) 82 21 207 98-69
E-Mail [email protected]
Web www.lth-gmbh.de
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project