CCTV TesterPro
CCTV testerPRO User’s Manual
www.b-qtech.com
B-Qtech Electronics Co.,Ltd
Email: [email protected] / [email protected]
USER’S MANUAL
Products certification:
CCTV TesterPro
Stest-890
Ms Shelly Yoe (GM)
MSN:[email protected] / Skype: bqshelly /
Page.23.
Tel: 0086-755-25852163 / 0086-15994792003
CCTV testerPRO User’s Manual
CCTV testerPRO User’s Manual
4. Specification
MODEL
CCTV Security TesterPRO
Video Test
Signal mode
NTSC/PAL (Auto adapt)
2.8 inch digital TFT-LCD ,960 x 240 resolution
Display
Ver:STP28V1.3
LCD adjustment
Brightness, Contrast, Saturation adjustable
1 channel BNC Input & 1 channel Output
Video IN/OUT
2009.5
Video Output Mode
1.0 Vp-p
Video Level test
Video signals measured in IRE or mV
PTZ controller
Communication
PTZ Protocol
RS232, RS422 simplex and RS485
Compatible with more than 20 protocols such as PELCO-D/P, Samsung,
Panasonic, Lilin, Yaan, etc.
150,300,600,1200,2400,4800,9600,19200bps
Baud Rate
Video Signal Generation
Color bar generation
Output channel colorbar video signal for testing monitor or video
cable
UTP CABLE TEST
UTP cable test
Test UTP cable connection status and display in the screen. Read
the number of the test box.
RS485 data analyst
Data Monitor
Captures and analyzes the command data from controlling device
POWER
Power Adapter
Battery
Rechargeable
Low Consumption
DC5V, 2A
Built-in 3.7V Lithium polymer battery ,2000mAh
After charging 3-4 hour, working time lasts 11 hours
Energy saving technology
General
Working
Temperature
-10℃---+50℃
Working Humidity
30%-90%
Dimension/Weight
166mmx95mmx48mm/293g
The data above is only for reference and any change of them will not be informed in advance.
For more detailed technical inquiries, please feel free to call the Technical Department of our
company.
Page.1.
Page.22.
CCTV testerPRO User’s Manual
CCTV testerPRO User’s Manual
up. Press
manual single-step decreasing button, the tester will search up the ID step by step
(from 256 to 1). When the ID is searched, the PTZ camera will stop panning.
Thank you for purchasing the CCTV security tester. Please read the manual before using the
CCTV testerPRO, and use properly.
Press
button , the tester will search up the ID quickly and continuously(from 256 to 1). When
the ID is searched, the PTZ camera will pan left. At this time, please press any key to stop searching
up. Press
manual single-step incremental button,the tester will search up the ID step by step
(from 1 to 256). When the ID is searched, the PTZ
manual.
The manual should be kept well in case of reference.
camera will stop panning.
Press the direction control button to adjust Speed Dome Camera. Press
For using the CCTV testerPRO safely, please first read the「Safety Information」carefully in the
button to quit from the
Keep the S/N label for after-sale service within warranty period. Product without S/N label will
be charged for repair service.
address-scanning function menu.
If there is any question or problem while using the CCTV testerPRO, or damages occurred on
the product, please contact our technical Department.
Page.21.
Page.2.
CCTV testerPRO User’s Manual
CCTV testerPRO User’s Manual
Table of Content
3.9 PTZ address scanning
Search up the ID of PTZ camera.
1 S a f e t y I n f o r m a t i o n ---------------------------------------------------------------------------3
Note:
2 I n t r o d u c t i o n ----------------------------------------------------------------------------------------4
PTZ cameras in the same system will pan at the same time.
2.1 Features ------------------------------------------------------------------------------------------4
Please isolate the PTZ camera with other PTZ cameras before searching up. Otherwise all the
Press
keys to
“Device setting”
menu:
Press
key to confirm after change “Address search:”
2.2 CCTV testerPRO Kits --------------------------------------------------------------------------5
2.3 Front Panel---------------------------------------------------------------------------------------6
2.4 Side View-----------------------------------------------------------------------------------------8
2.5 Installing the Battery----------------------------------------------------------------------------9
3 Operation----------------------------------------------------------------------------------------------11
to “on”, which add address scan sub-menu. Press
to switch the sub-menu as illustrated:
3.1 Power on/off-------------------------------------------------------------------------------------11
(Note: The system returns to “OFF” after shutdown, and the
3.2 Menu & Functions------------------------------------------------------------------------------11
scan sub-menu closes automatically. Set “ON” again for next
3.3 PTZ controller-----------------------------------------------------------------------------------13
use.)
3.4 Video setting ------------------------------------------------------------------------------------16
Press
3.5 Colorbar generator ----------------------------------------------------------------------------16
communication rate, make them same as the PTZ camera
3.6 Cable tester--------------------------------------------------------------------------------------17
Press
key to set: protocol, communication port,
or
key, the address values is constantly on the rise or decrease.
3.7 Data monitor ------------------------------------------------------------------------------------17
NEAR:
3.8 Device setting-----------------------------------------------------------------------------------18
The tester will search up the ID quickly and continuously(from 1 to 256). When the ID
is searched, the PTZ camera will pan right. At this time, please press any key to stop
3.9 Address search----------------------------------------------------------------------------------19
searching up.
4 Specifications ----------------------------------------------------------------------------------------------21
FAR:
The tester will search up the ID quickly and continuously(from 256 to 1). When the
ID is searched, the PTZ camera will pan left. At this time, please press any key to
stop searching up.
WIDE:
The tester will search up the ID step by step (from 1 to 256). When the ID is searched,
the PTZ
FAR:
camera will stop panning.
The tester will search up the ID step by step (from 256 to 1). When the ID is searched,
the PTZ camera will stop panning.
Press
button,
the tester will search up the ID quickly and continuously(from 1 to 256). When
the ID is searched, the PTZ camera will pan right. At this time, please press any key to stop searching
Page.3.
Page.20.
CCTV testerPRO User’s Manual
a.
Connect the RS485 or RS232 interface of controlling system with the RS485 or RS232
CCTV testerPRO User’s Manual
1.
Safety Information
interface of the CCTV testerPRO (In case of RS485, A to A, B to B)
b.
Press SET key and then press
or
key to select communication port according to
Notice
the system connection. Press SET key to save the change.
The tester is intended to use in compliance with the local rules of the electrical
d.
Press
or
key to select the baud rate according to the baud rate of controlling
usage and avoid to apply at the places which are inapplicable for the use of
system and then press SET key to save the change and capture command data from
electrics such as hospital, gas station etc.
controlling system.
e.
To prevent the functional decline or failure, the product should not be sprinkled
Press RETURN key to clear the screen.
or damped.
The exposed part of the tester should not be touched by the dust and liquid.
3.8 Device setting
During transportation and use, it is highly recommended to avoid the violent
Set the parameters of the CCTV testerPRO
collision and vibration of the tester, lest damaging components and causing
failure.
Don’t leave the tester alone while charging and recharging. If the battery is
found severely hot, the tester should be powered off from the electric source at
once. The test should not be charged over 8 hours.
Don’t use the tester where the humidity is high. Once the tester is damp, power
off immediately and move away other cables connected.
Auto poweroff: Setting the time of auto shut-down.(Disable,5,10,…,60)
The tester should not be use in the environment with the flammable gas.
Disable: Disable the “Auto poweroff” function. 5 means the CCTV will power off
Do not disassembly the instrument since no component inside can be repaired
after 5 minutes when there is no any operation.
by the user. If the disassembly is necessary indeed, please contact with the
Keypad tone: Open or close the beep of pressing keypad.
technician of our company.
Language: Select language of OSD menu
The instrument should not be used under the environment with strong
Brightness: Setting the brightness of OSD menu and background.(0~7)
electromagnetic interference.
Don’t touch the tester with wet hands or waterish things.
a. Press
or
b. Press
or
key to move the parameter we want to change.
Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt
to change the value.
is not easy to remove, the soft cloth with water or neutral detergent can be
c. Press ENTER to save the change or press RETURN key to give up the change.
used., but the cloth should be tweaked sufficiently.
Page.19.
Page.4.
CCTV testerPRO User’s Manual
CCTV testerPRO User’s Manual
2.
Introduction
The CCTV testerPRO is developed for the On-Site installation and maintenance of video
monitoring system.
a.
Press the
or
key to select the parameter which we want to change the value.
b.
Press the
or
key to change the value.
c.
Press ENTER key to save the change or press RETURN key to give up the change
It can be used for displaying video, controlling PTZ, generating images,
capturing data of RS485 and testing LAN cable etc. Its functions, easy operation, and portability
makes it simple for the CCTV technician to install and maintain CCTV system, improving work
3. 6
Cable Tester
Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV testerPRO and cable tester. And then the
efficiency and get the labor cost down.
connecting status, cable type and the sequence of wires will be displayed, as well as the serial
number of the cable tester kit
2.1 Features
2.8"TFT-LCD , 960(H)×240(V)resolution.
PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and sets
and calls the preset position
Video displaying. Automatically adapts and displays the video format of NTSC/PAL.
LCD Brightness/Contrast/Color Saturation are adjustable.
Video Level testing, video signals measured in IRE or mV
Video Generating, The PAL/NTSC multi-system colorbar video generator (seven-system
The right picture shows line1-7 are closed, line8 is open and the number of the cable tester box is 255
switchable, transmit/receive seven-system colorful imagines)
Data analyst. Captures and analyzes RS485 controlling data to help the technician to find out
the problem.
Cable testing. It is powerful in testing LAN cable, measuring the connecting status ,displaying
the sequence of connection and the NO. of the LAN cable.
Multi-interface and Multi-baudrate. Support RS232 ,RS485 and RS422 interface; baud rate
Straight-through Line
ranging from 150, 600 to 19200bps.
Cross Line
Multi-protocol. Supports more than twenty PTZ protocols. For example, PELCO-P, PELCO-D,
3.7. Data monitor
SAMSUNG etc.
Capture the command data from RS485 controlling system.
PTZ address scanning, search up the ID of PTZ camera.
Lithium Ion Polymer Battery (3.7V DC2000mAh). The device employs advanced power control
and protection circuit. The device is high power-efficient, energy saving and environmental
protection. It can last 11 hours for normal use after charging for 4 hours.
Page.5.
Page.18.
Open Line or Short Line
CCTV testerPRO User’s Manual
3.4.
Video Setting
CCTV testerPRO User’s Manual
2.2
CCTV testerPRO Kits
User can customize the brightness, contrast and saturation of the LCD according to the using
environment , the CCTV tester auto display the format(PAL/NTSC) of video input, and analysis
Professional design, light and portability, video display and data control are deliberately
the input video signal level.
integrated, which makes the instrument so simple, practicable, easy for use that the training is
almost unnecessary for an operator to be skillful.
a.
Press the
or
key to select the parameter which we want to change the value.
b.
Press the
or
key to change the value. Press ENTER key to save the change
or press RETUR key to give up the change
c.
1. CCTV testerPRO
3. LAN Cable Tester
5. BNC Cable
The Video Format and Video Level will be displayed in the lower portion of the screen. If
6. Safety cord
there is no video signal at the Video IN port of the CCTV TesterPRO, the type of NTSC or
PAL , and Video Level will not be displayed.
Depending on the type of camera connected to the CCTV testerPRO, the Video “Format: “ will
automatically change between NTSC and PAL, and the Video Level will automatically change
7. RS485 data cable
between IRE (Institute of Radio Engineers) and mV. NTSC signals measured in IRE units, PAL
2. Power Supply (5V 2A)
signals measured in mV.
The Video Level should be within the indicated range. Levels that are too low will result in a
dim picture with reduced dynamic range. A Video Level that is too high will result in washed
out pictures with decreased. The CCTV testerPRO will display “Normal” when video levels are
1000mV±20%,
3.5.
“Exceed” or “Weak” will be displayed when video level out of 1000mV±20%.
Colorbar generator (Output video at any mode)
Output or receive seven different forms of video color bar to test monitor, video cable or other
equipment.
Page.17.
Page.6.
4.
Lithium Ion Polymer Battery
8. Instruction Manual
CCTV testerPRO User’s Manual
2.3
CCTV testerPRO User’s Manual
c.
Front Panel
Press
or
key to select the preset number 64, and then press ENTER key to
call OSD menu of the PTZ controller.
OSD Menu of Dome (For reference only)
MAIN MENU
„
MAIN MENU
1. DISPLAY SETUP
1. Display configuration
2. CAMERA SETUP
2. Set camera parameters.
3. CONTROL SETUP
3. Set PTZ controlling
4. CAMERA MASK SET
4. Set privacy mask
5. PROGRAM
5. Set auto-running functions
6. PAL CAMERA
6. PAL/NTSC Switch
7. CAM DEFAULT SET
7. Restore the default settings
8. DOME RESET
8. Reset the dome
9. EXIT
9. Exit the main menu
Operate auto-running functions by calling preset position(effective for some brands of
PTZ camera)
Call preset-33—Open Auto-flip function
Call preset-34—Reset zero point of PTZ camera
Call preset-64—Enter the main menu of the PTZ camera
Call preset-95—Enter the main menu of the PTZ camera or stop the PATTERN recording.
Call preset-96—Run pattern-1
Call preset-97—Run preset tour-1
1
The power indicator: it lights green while the tester is powered on.
2
The data-reception indicator: it lights red while the data is being received.
Call preset-98—Run frame Scan
Call preset-99—Run Auto scan
The data-transmission indicator: it lights red while the data is being
3
transmitted
The charge indicator: it lights red while the battery is being charged. As
4
the charging is complete, the indicator turns off automatically.
5
The display Icon of battery electricity: it displays the electric quantity
6
Main-menu: it shows main functions of CCTV testerPRO.
Page.7.
Page.16.
CCTV testerPRO User’s Manual
CCTV testerPRO User’s Manual
A. Protocol:
Select the protocol according to the protocol of the PTZ camera. Up to 21
7
Sub-menu: Shows and sets the values of functions
popular protocols are available, like elco P, Pelco D, Samsung, Yaan, LiLin, CSR600 etc.
Long-pressing it more than 2 seconds to turn on/off the tester;
8
B. Port: Select the communication port for the PTZ camera controlling (RS232/422/485)
short-pressing to turn on/off the PTZ controller menu displaying.
C. Baud: Select the baudrate according to baudrate of the PTZ camera.(150, 300, … , 19200bps)
Menu key: it pops up the main-menu; constant-press it or press the
9
or
key can shift between functions
D. Address: Set the ID according the ID of PTZ camera (0~254).
Setup key : press it or press left or right key to enter sub-menu to set the
10
parameters of functions.
E. Pan Speed: Set the pan speed of PTZ camera (0~63)
Upward : Select the item which will be set or add the value of the
F. TiltSpeed: Set the tilt speed of PTZ camera (0~63)
11
parameter. Tilt the PTZ upward.
G. Set PS: Setup preset position (0~128)
Leftward : Enter the sub-menu or select the parameter whose value will be
12
a. P/T/Z the camera to desired position
changed. Reduce the value of the parameter. Pan the PTZ left.
b. Press SET key to enter PTZ controller submenu
c. Move the yellow cursor to “Set PS” and then press
or
key to select the preset
Rightward : Enter the sub-menu or select the parameter whose value will
13
be changed. Add the value of the parameter. Pan the PTZ right.
position number.
d. Press ENTER key to complete preset position setting or preset RETURN key to give up
Tips: Press
or
Downward : Select the item which will be set or reduce the value of the
14
preset position setting.
parameter. Tilt the PTZ downward.
key to accelerate the value changing.
15
Confirm/Open : Confirm the setting of parameters; open the aperture.
H. Go PS: Call the preset position. (0~128) The PTZ camera will go to the desired preset position.
a. Move the yellow cursor to “Go PS” and then press
or
key to select the preset
Return/Close : Return or cancel while setting parameters of the menu;
16
close the aperture
position number.
b. Press ENTER key to complete preset position calling or preset RETURN key to give up
preset position calling.
Tips: Press
or
17
Near focus: Focus the image nearby.
18
Far focus: Focus the image faraway.
19
TELE: zoom in the image
20
WIDE: zoom out the image
key to accelerate the value changing.
The way of calling the OSD menu and preset of the PTZ camera may vary with control systems
from different manufacturers. Please read the operation manual of control system manufacturer
for details. The way of calling OSD provided for reference is calling preset-64.
a.
Move the yellow cursor to “PTZ controller” to enter PTZ controller mode
b.
Press SET key to enter PTZ controller sub-menu. Press
or
key to move
the yellow cursor to “Go PS”,
Page.15.
Page.8.
CCTV testerPRO User’s Manual
CCTV testerPRO User’s Manual
2.4
Side view
3.2
PTZ Controller
Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the
controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set
and call preset position.
The following connections should be confirmed before use
a. The Video In interface of the CCTV testerPRO and the output interface of camera
b. Data A+ of the CCTV testerPRO and A+ of the PTZ camera or controlling device, data B- of
the instrument and B- of the PTZ camera or controlling device
Note:
Left Side
Top View
Don’t connect communications interface with a circuit the voltage higher than 6V.
Right Side
22
Reset the default settings of parameters.
23
External power supply (DC, 5V): It is highly recommended to use the equipped power
adapter.
24
UTP cable port: Please use together with UTP LAN cable tester.
25
RS232 interface: RS232 communication for the PTZ.
26
Video input (BNC input interface): Inputs the video.
27
Video output (BNC output interface): Outputs the video.
28
RS485/422 Interface: RS485/RS422 communication for the PTZ.
a. Press SET key to enter the sub-menu of PTZ controller.
b. Press the
29
Hole for the safety cord.
or
key to select the parameter
which we want to change the value.
c. Press ENTER key to save the change or press RETURN
key to give up the change
d. Press SET key to exit the sub-menu.
e. Press POWER key to full-screen the image
Page.9.
Page.14.
CCTV testerPRO User’s Manual
CCTV testerPRO User’s Manual
2. Video setting
2.5
Installing the Battery
Adjust the LCD brightness, Contrast, Color saturation.
The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery
Video Format displaying and Video level testing
cabin should be disconnected for safety during transportation!
Prior to the use of the instrument, the battery cables inside the battery cabin should be
well connected and the color of cables should be at the same side.
Usually it need not to disconnect the cable at the normal use, pressing
3. Colorbar generator
key
continuously can power on or off the tester.
Output or receive seven different forms of video color bar to
At the first time of use, the batteries should be completely exhausted and then
tester monitor, cable or other equipment.
recharged for 4 or 5 hours.
The Charge Indicator
lights red when charging the battery, The charge indicator
turns off automatically when the charging is completed.
△
Notice: When the Charge Indicator
turns off, the battery is approximately 90% charged.
4. Cable tester
The charging time can be extended for about 1 hour and the charging time within 8
Test LAN cable or telephone cable.
hours will not damage the battery.
The connecting condition and the sequence of wires will be
△
The tester can work as usual while it is being charged, however. But the charging time will
displayed, as well as the serial number of the cable tester kit.
be extended.
Press the RESET key at the right of the instrument to restore the default settings
instrument works abnormally.
5. Data Monitor
Unlock the battery cover by pushing horizontally as the direction illustrated
Captures the protocol from the controlling system and display
command data. It is helpful to debug and maintain RS485
communication.
6. Device setting
Set the parameters of the CCTV testerPRO (Auto poweroff/
Keypad tone/Language/Brightness)
Page.13.
Page.10.
when the
CCTV testerPRO User’s Manual
Warning: Connect the terminal of the battery with the direction illustrated. Please take
CCTV testerPRO User’s Manual
3. Operation
care of the polarity of terminal.
3.1 Power on
Continuously press
(The wires of the same color should be both at the one side)
(at least 2 seconds) to power on/off the CCTV testerPRO. When the
CCTV testerPRO is powered on,press MODE key the main-menu will pop up.
Menu & Functions
Press MODE key continuously or press the
or
key to select the function (PTZ controller,
Video settings, Colorbar generator, LAN cable tester, Data monitors, Device setting) and enter
corresponding function setting sub-menu. Press SET key to set the parameters in function sub-menu.
Note: When the CCTV testerPRO is powered on, it will return to the function which is being operated
Lock the batteries by pressing as the direction illustrated
before it is turned off.
1. PTZ controller
Display the input video images. Pan/tilt the P/T unit and zoom
in/ out the image. Setup the controlling parameters like protocol,
communication port, baud rate, PTZ ID, pan/tilt speed; set and
call preset position.
Page.11.
Page.12.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement