AVerVision SPB350+ User Manual
ENGLISH
FCC NOTICE (Class A)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Federal Communications Commission Statement
NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
Class A ITE:
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment
should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning - This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
CE Class A (EMC)
This product is herewith confirmed to comply with the requirements set out in the Council Directives on the
Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive 2004/108/EEC.
Warning - This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures to correct this interference.
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the contents of this documentation, its
quality, performance, merchantability, or fitness for a particular purpose. Information presented in this documentation has been
carefully checked for reliability; however, no responsibility is assumed for inaccuracies. The information contained in this
documentation is subject to change without notice.
In no event will AVer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability
to use this product or documentation, even if advised of the possibility of such damages.
TRADEMARKS
AVerVision is registered trademarks of AVer Information Inc. IBM PC is a registered trademark of International Business
Machines Corporation. Macintosh is a registered trademark of Apple Computer, Inc. Microsoft is a registered trademark and
Windows is a trademark of Microsoft Corporation. All other products or corporate names mentioned in this documentation are
for identification and explanation purposes only, and may be trademarks or registered trademarks of their respective owners.
COPYRIGHT
© 2012 by AVer Information Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form by any means without the written permission of AVer
Information Inc.
THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS PRODUCT MUST
NOT BE DISPOSED OF WITH YOUR OTHER HOUSEHOLD WASTE. INSTEAD, YOU NEED
TO DISPOSE OF THE WASTE EQUIPMENT BY HANDING IT OVER TO A DESIGNATED
COLLECTION POINT FOR THE RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT. FOR MORE INFORMATION ABOUT WHERE TO DROP OFF YOUR WASTE
EQUIPMENT FOR RECYCLING, PLEASE CONTACT YOUR HOUSEHOLD WASTE
DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE PRODUCT.
Bat t e r y S af et y In f o r m at i o n
-
Store the batteries in a cool dry place.
Do not dispose of used batteries in domestic waste. Dispose of batteries at special collection points or return to
point of sale if applies.
Remove the batteries during long periods of non-use. Always remove exhausted batteries from the remote control.
Battery leakage and corrosion can damage this remote control, dispose of batteries safely.
Do not mix old and new batteries.
Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
Do not dispose of batteries in a fire. The batteries may explode or leak.
Never short circuit the battery terminals.
ENGLISH
Table of Contents
Introduction ........................................................................................................................................... 1
Package Contents .................................................................................................................................. 1
Optional Accessories ............................................................................................................................. 1
AVerVision SPB350+ Parts ..................................................................................................................... 2
Making the Connections ......................................................................................................................... 3
Connecting a VGA, Mac Monitor or LCD/DLP Projector ................................................................. 4
Connecting a Monitor or LCD/DLP Projector with DVI interface ..................................................... 5
Connecting a TV .............................................................................................................................. 5
Connecting the Power Adapter ........................................................................................................ 6
Connecting a Computer ................................................................................................................... 6
Connecting a Computer via USB Connection ................................................................................. 6
Inserting and Ejecting a SD Card .................................................................................................... 7
Setting Up SPB350+ ............................................................................................................................... 7
Arm................................................................................................................................................... 7
Camera Head ................................................................................................................................... 7
Overhead Light ................................................................................................................................ 8
Infrared Sensor ................................................................................................................................ 8
Light Box .......................................................................................................................................... 8
Anti-glare .......................................................................................................................................... 8
Microscope Connection ................................................................................................................... 9
Control Panel Light Color ................................................................................................................. 9
Using the Infrared Remote Control ....................................................................................................... 10
Touch Button Control Panel ................................................................................................................. 12
Using AVerVision SPB350+ as a Mass Storage ..................................................................................... 13
OSD Navigation Tree ............................................................................................................................ 14
Menu Functions ................................................................................................................................... 15
Technical Specifications ...................................................................................................................... 18
Using the RS-232 Interface .............................................................................................................. 19
RS-232C Diagram Connection ...................................................................................................... 19
RS-232C Cable Spec ..................................................................................................................... 19
RS-232C Transmission Spec ......................................................................................................... 19
RS-232C Communication Format.................................................................................................. 19
Send Command Format: .......................................................................................................... 19
Set Value Format: ..................................................................................................................... 20
Get Value Format: ..................................................................................................................... 21
Troubleshooting................................................................................................................................... 21
Limited Warranty.................................................................................................................................. 22
ENGLISH
Introduction
Package Contents
Your AVerVision SPB350+ package contains the following:
Thank you for purchasing the
AVerVision SPB350+. This
interactive visualizer displays
documents, negatives,
transparencies and 3D objects
onto a TV, LCD or DLP
projector making
demonstrations a snap.
POWER
ENTER
PLAYBACK
FREEZE
ROTATE
SPLIT SCRN
The advanced features of the
AVerVision SPB350+ make it a
versatile and multi-functional
product. Integrated with the
new powerful zoom feature,
AVer Optical Zoom is a
combination of optical zoom
with AVERZOOM.
AVERZOOM is an AVer
patented technology which
digitally zooms in and pans on
an image while maintaining
optical zoom image quality.
You can save still images in
the built-in memory, or SD
memory card. When
connected to a computer via
USB connection and with the
bundled software, you can
capture and save still images
and video clips to your hard
drive directly. It also comes
with a fully-featured remote
control.
CAMERA/PC
MENU
AUTO IMAGE
CAP/DEL
AUTO FOCUS
TIMER
PROFILE
PRESENTER
PIP
RM-NK
Remote Control
(batteries included)
Manual CD
AVerVision SPB350+
R
DUST COVE
Dust Cover
Anti-glare Sheet
Installation CD
RCA Cable
Power Adapter
S-Video Cable
Power Cord
RGB Cable
* The power cord varies depending on the
standard power outlet of the country where it is
sold.
Optional Accessories
34mm Microscope Adapter
28mm Microscope Adapter
1
USB Cable
ENGLISH
AVerVision SPB350+ Par ts
The illustrations below identify the parts of SPB350+.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Camera head
Camera lens
Left panel
Light box
Control panel
Overhead light
Arm
IR sensors
Rear panel
Label slot
Right panel
(1)
(6)
(7)
(2)
(8)
(3)
(9)
(4)
(5)
(10)
(11)
Left Pane l
12. CVBS OUT
(RCA/Composite)
13. S-Video output port
14. DVI-I output port
15. USB port
16. SD card slot
(12)
(13)
S-VIDEO OUT CVBS OUT
DVI-I OUT
USB
S-VIDEO OUT
CVBS OUT
DVI-I OUT
USB
(14)
(15)
(16)
SD CARD
SD CARD
Rea r Pane l
17.
18.
19.
20.
21.
DC 12V port
RS-232 port
RGB IN 2 port
RGB IN 1 port
RGB output port
DC 12V
RS-232
RGB IN 2
RGB OUT
IOIOI
(17) (18)
(19) (20) (21)
(22)
(23)
Righ t Pane l
22. Video output switch
23. Light box power
button
24. Antitheft slot
RGB IN 1
VIDEO OUTPUT
TV
RGB
LIGHT BOX
(24)
VIDEO OUTPUT LIGHT BOX
TV
2
RGB
ENGLISH
Making the Connections
The ports on the rear, left and right panel of SPB350+ enable you to connect the unit to a computer, graphics
display monitor or LCD/DLP projector, TV or other device. Illustrated below are the ports that are located at the
rear and right panel of SPB350+ with their corresponding labels.
Rear Panel
DC 12V
RS-232
RGB IN 2
RGB IN 1
RGB OUT
IOIOI
(1)
(3)
(2)
(4)
Name
Function
(1) DC 12V
: Connect the power adapter into this port.
(2) RS-232
: Receive command from the computer to operate
SPB350+. Connect this port to the RS-232 port of the
computer.
: Takes as input the signal from a computer or other sources
and pass it through to the RGB Output and DVI-I port only.
Connect this port to the VGA output port of the computer.
: Output the signal from the camera, RGB IN port, or the
captured images from the memory source on a VGA/Mac
monitor or LCD/DLP projector.
(3) RGB IN 1 & RGB
IN 2
(4) RGB OUT
Left Panel
S-VIDEO OUT CVBS OUT
DVI-I OUT
USB
SD CARD
(1) (2) (3) (4) (5)
Name
Function
1. S-VIDEO OUT
: Output the signal from the camera or the captured images
from the memory source on TV or Video equipment.
: Output the signal from the camera or the captured images
from the memory source on TV or Video equipment.
2. CVBS OUT
(RCA/Composite)
3. DVI-I OUT
4. USB
5. SD card slot
: Output the signal from the camera, RGB IN 1/2 port, or the
captured images from the memory source on a VGA/Mac
monitor or LCD/DLP projector with DVI-I interface. If the
display device does not support DVI-I, it can only display
the signal from the camera and the captured images.
The1920 X1080 resolution for DVI-I support reduced
blanking only.
: Use SPB350+ as a USB Camera or Mass Storage to
transfer the captured images from SPB350+ memory
source to PC.
: Insert the SD card with the label facing up. It can support
16MB~2GB card capacity and only accepts FAT16
formatted card.
3
ENGLISH
Right Panel
VIDEO OUTPUT LIGHT BOX
TV
RGB
(1) (2) (3)
Name
Function
(1) VIDEO
OUTPUT
(2) LIGHT BOX
(3) Antitheft slot
: Select to output video signal between RGB (RGB & DVI-I) or
TV (Composite Video/S-Video) display output.
: Turn on/off the light box.
: Attach a Kensington compatible security lock or antitheft
device.
C o n n e c t in g a VGA , Ma c Mo n ito r o r LC D / D L P P r o je c to r
Locate the RGB (VGA) input port of the display device and connect it to RGB OUT port of SPB350+. If you are not
sure, please refer to the user manual of the device.
Make sure the Video Output switch is set to RGB.
DC 12V
RS-232
RGB IN 2
IOIOI
LCD/DLP projector
RGB cable
(not supplied)
CRT monitor
CAM
LCD monitor
MAC monitor
4
Monitor Adapter
(not supplied)
RGB IN 1
RGB OUT
ENGLISH
C o n n e c t i n g a M o n i t o r o r LC D / D L P P r o j e c t o r w i t h DV I i n t e r f a c e
Locate the DVI input port of the display device and connect it to DVI-I OUT port of SPB350+. If you are not sure,
please refer to the user manual of the device.
Make sure the Video Output switch is set to RGB.
S-VIDEO OUT
CVBS OUT
DVI-I OUT
USB
SD CARD
LCD Monitor
with DVI interface
DVI cable
(not supplied)
LCD/DLP Projector
with DVI interface
Connecting a TV
Locate the VIDEO (yellow), S-VIDEO or SCART RGB input port of the TV or Video equipment (i.e., VCR) to record
your presentation on a videotape and connect it to S-VIDEO or CVBS OUT port of SPB350+. If you are not sure,
please refer to the user manual of the TV or Video equipment.
- Make sure the Video Output switch is set to TV.
- For better video quality, we strongly suggest using S-VIDEO connection.
S-VIDEO OUT
CVBS OUT
DVI-I OUT
USB
SD CARD
INPUT
RCA to SCART cable
(not supplied)
SCART
RCA cable
VIDEO
S-Video cable
S-VIDEO
S-Video to SCART cable
(not supplied)
5
Projector
TV
SCART
VCR
ENGLISH
C o n n e c t i n g t h e Po w e r A d a p t e r
Connect the power adapter to a standard 100V~240V AC power source.
DC 12V
RS-232
RGB IN 2
RGB IN 1
RGB OUT
IOIOI
Wall outlet
Power adapter
Power cord
Connecting a Computer
Locate the RGB (VGA) output port of the computer or laptop to display your PC presentation on screen and
connect it to RGB IN 1 or RGB IN 2 ports of SPB350+. The video signal from the RGB IN port is streamed to RGB
and DVI-I OUT ports only. Press CAMERA/PC button on the control panel or remote to switch to PC-1 or PC-2.
DC 12V
RS-232
RGB IN 2
RGB IN 1
RGB OUT
IOIOI
Computer
RGB cable
Laptop
Monitor Adapter
(not supplied)
MAC
Connecting a Computer via USB Connection
Locate the USB port of the computer or laptop and connect it to USB port of SPB350+. This enables you to use
SPB350+ as a USB Camera and to transfer the captured images from the memory source and to computer. Also
see “Using AVerVision SPB350+ as a Mass Storage”.
S-VIDEO OUT
CVBS OUT
DVI-I OUT
USB
SD CARD
USB cable
Computer
Notebook
6
ENGLISH
Inser ting and Ejecting a SD Car d
Insert the card with the label facing up until it reaches the end. To remove, pull the card out. The supported SD
card capacity is from 16MB to 2GB. Make sure the card is formatted to FAT16. SPB350+ automatically creates and
stores the images in AVERJPG folder.
DC 12V
RS-232
IOIOI
D
SD CAR
USB
RGB IN
2
RGB IN
DVI-I
OUT
1
CVB
RGB OUT
S-VIDE
S OUT
O OUT
SD card
(not supplied)
Setting Up SPB350+
This section provides useful tips on how to adjust the SPB350+ to meet your needs.
Ar m
The arm must be unfolded fully in upright position.
90°
90°
S-VIDEO OUT CVBS OUT
DVI-I OUT
USB
SD CARD
S-VIDEO
DEO OUT
OU
CVBS OUT
OU
DVI-I OUT
USB
SD CARD
Camera Head
The camera head can be folded up 90° and turned 90° to the left and right. To display an object more than 50cm
away from the camera, unscrew the close-up lens. Do not forget to screw back the close-up lens afterwards.
50cm
90°
90°
S-VIDEO OUT CVBS OUT
DVI-I OUT
USB
SD CARD
7
ENGLISH
O ve r h e a d L i g h t
Press LAMP button on the control panel to turn on and off light.
S-VIDEO OUT CVBS OUT
DVI-I OUT
USB
SD CARD
Infrared Sensor
Aim the remote control at the infrared sensors to operate the unit.
L i g h t B ox
Press LIGHT BOX button on the right panel of SPB350+ to turn on and off light. Use this to view negatives film,
and 35mm slides.
: DO NOT place an object weighing more than 8kg on top of the light box.
Light Weight Object
Photos
+)
g(
K
8
Light Box Button
Negative Film
Document
Anti-g lare
The anti-glare sheet is a special coated film that helps eliminate any glare that may be
encountered while displaying very shiny objects or glossy surfaces such as magazines and
pictures. To use, simply place the anti-glare sheet on top of the shiny document to reduce
reflected light.
8
ENGLISH
Microscope Connection
Connecting the SPB350+ to a microscope enables you to examine microscopic objects on a big screen without
straining your eyes.
1. Change the image display mode to Microscope.
Press MENU > select SETTING > MODE >
MICROSCOPE and press ENTER.
2. Adjust the microscope focus to its best clarity.
Then, select the appropriate adapter size that
would fit the microscope eyepiece.
Close-up Lens
3. Unscrew the close-up lens from the camera
head.
4. Remove the microscope eyepiece from the
microscope and connect it to the microscope
adapter. Then, fasten the 3 bolts until the
adapter secures the eyepiece.
Microscope Adapter
(optional)
Microscope
We suggest using a microscope with an
eye relief of 15.5mm or higher for better
view.
5. Screw the microscope adapter to the
AVerVision camera head. Then, connect it to
the microscope.
C o n t r o l Pa n e l L i g h t C o l o r
The LED power button on the control panel of SPB350+ indicates the status of the unit.
Color
Description
Blue
: The unit is in operating mode.
Orange
: The unit is in standby mode.
9
ENGLISH
Using the Infrared Remote Control
Use the SPB350+ Remote Control to enhance your presentation by having the ability to switch between three (3)
presentation modes and access various features. To use the remote control, first insert the batteries (2 “AAA” size
batteries are provided) into the battery compartment at the back of the remote. Use the figure and descriptions
below as a reference for remote control functions.
(1)
POWER
Name
Function
(1) POWER
Turn the unit on/off.
(2) Shuttle Wheel
-
When it exceeds the maximum optical zoom level of
about 12X, you may still continue to AVer Optical
zoom up to 1.66X AVerZoom and 8X digitally zoom.
Press ENTER to return to normal view (100%). The
zoom bar indicator will turn from blue to aqua to
indicate that you can pan around the image.
(2)
ENTER
(3)
(4)
(5)
(12 )
PLAYBACK
MENU
-
CAMERA/PC
(6)
(13 )
AUTO IMAGE
CAP/DEL
FREEZE
AUTO FOCUS
(14 )
(15 )
(16 )
ROTATE
TIMER
SPLIT SCRN PRESENTER
PROFILE
PIP
Turn the shuttle wheel clockwise to zoom in and
counter-clockwise to zoom out the image optically
and digitally in Camera and Playback mode only.
(7)
(8)
(9)
(10 )
(11)
Press the shuttle wheel ▲,▼,◄, & ► to pan the
image while in digital zoom mode, to make a
selection on 16-thumbnail images or move to the
next or previous single full screen preview in
Playback mode, or to make a selection or
adjustment on the OSD main-menu and sub-menu
(See Menu Functions for more details).
RM-NK
Name
Function
(3) ENTER
Make a selection in Playback mode and OSD menu. Use this to quick zoom to 200% or back to
100% in Camera mode only.
(4) MENU
Pull up and exit the OSD main-menu and sub-menu.
(5) Camera/PC
Switch between Camera and PC mode.
- Camera mode displays the video signal from the built-in camera.
- PC mode displays the video signal from the RGB IN 1 and RGB IN 2 port of SPB350+. The
PC1 and PC2 will display the video signal from RGB IN 1 and RGB IN 2 respectively.
(6) CAP/DEL
- Capture a still image in Camera mode. The captured image is saved in the selected memory
source at 1600 x 1200 resolution and the built-in memory can store up to 240 images.
- Remove the selected picture from the selected memory source permanently in Playback
mode.
(7) AF (Auto Focus)
Adjust the focus automatically.
(8) TIMER
Display the OSD timer menu and use ▲or▼ buttons to select SET TIME to set the time value,
START to begin the countdown timer, PAUSE/RESUME to temporarily halt or continue, and
STOP to end. Press MENU to hide the timer menu.
(9) PROFILE
Recall and switch from the 3 saved user setting profile selections (See MENU Functions – SAVE
for more details).
(10) PIP
Display/hide a thumbnail of the captured image from the memory source at the corner of the
screen while in Camera mode.
Use ◄ or ► buttons to move to the previous or next image and ENTER to display the image in
full screen. To move the mini playback screen to different corners, press MENU, go to PIP and
select the position of the mini playback screen.
10
ENGLISH
Name
(11) PRESENTER
Function
Select to turn on/off SPOTLIGHT or VISOR. Only one feature can be used at a time.
SPOTLIGHT overlays a frame on the presentation
screen.
Selecting SHADE changes the opacity of the area
outside the box
from 0%, 50% and 100%, COLOR to change the
frame color
from red, green and blue, and RESIZE to change
the size of the
frame. To resize or move the frame around the
presentation
screen, press the shuttle wheel ▲,▼,◄, & ►.
VISOR covers part of the presentation screen. The
the presentation screen is slightly exposed
called each time. To expose part of the covered
shuttle wheel ▲,▼,◄, &►. Select SHADE to
darkness of the shaded area between 50% or
(12) PLAYBACK
upper part of
when it is being
area, press the
hange the
100%.
Playback mode displays the captured image from the memory source in 16-thumbnail images.
Use ▲,▼,◄, & ► buttons or rotate the shuttle wheel to make a selection and ENTER to
display the selected image in full screen.
Press MENU to display the Playback menu. Select SLIDE SHOW to start or set the time interval
between frames in second, MEMORY SOURCE to select the image location between the built-in
memory or SD card, and DELETE to permanently remove the selected image from the selected
memory source.
(13) AUTO IMAGE
Automatically adjust and set the white balance and exposure setting.
(14) FREEZE
Toggle to pause or resume the camera.
(15) ROTATE
Turn the image by 90°in Camera mode and 180° in full screen Playback mode.
(16) SPLIT SCRN
Turn on/off split screen mode. Split Screen divides the screen into two parts. One side displays
the live image from the SPB350+ camera and the other side displays the captured images from
the memory source in 8-thumbnail preview.
Use the ▲,▼,◄, &► buttons to make a selection and ENTER to enlarge the selected image in
split screen mode. To horizontally or vertically pan the enlarged image, use the ◄ & ► or ▲&▼
buttons. To switch to different split screen type, press MENU, go to SPLIT SCREEN and select
between vertical or horizontal splitting type.
11
ENGLISH
Touch Button Control Panel
The touch button control panel located on the top side of AVerVision SPB350+ provides quick access to commonly
used functions.
(5)
(6)
(7)
(2)
(4)
(3)
(1)
POWER
CAMERA/PC
RGB
PC1
TV
PC2
PLAYBACK
ENTER
MENU
(14)
Name
(13) (12)
(11)
AUTO IMAGE
ROTATE
LAMP
AUTO FOCUS
FREEZE
CAP/DEL
(10)
(9)
(8)
Function
(1) POWER
Turn the unit on/off.
(2) Camera/PC
Switch between Camera and PC mode.
- Camera mode displays the video signal from the built-in camera.
- PC mode displays the video signal from the RGB IN 1 and RGB IN 2 port of
SPB350+. The PC1 and PC2 will display the video signal from RGB IN 1 and
RGB IN 2 respectively.
(3) PLAYBACK
Playback mode displays the captured image from the memory source in 16thumbnail images. Use ▲,▼,◄, & ► buttons or rotate the shuttle wheel to make
a selection and ENTER to display the selected image in full screen.
Press MENU to display the Playback menu. Select SLIDE SHOW to start or set
the time interval between frames in second, MEMORY SOURCE to select the
image location between the built-in memory or SD card, and DELETE to
permanently remove the selected image from the selected memory source.
(4) ENTER
Make a selection in Playback mode and OSD menu. Use this to quick zoom to
200% or back to 100% in Camera mode only.
(5) AUTO IMAGE
Automatically adjust and set the white balance and exposure setting.
(6) ROTATE
Turn the image by 90°in Camera mode and 180 in full screen Playback mode.
(7) LAMP
Turn the overhead light on/off.
(8) CAP/DEL
- Capture a still image in Camera mode. The captured image is saved in the
selected memory source at 1600 x 1200 resolution and the built-in memory can
store up to 240 images.
- Remove the selected picture from the selected memory source permanently in
Playback mode.
(9) FREEZE
Toggle to pause or resume the camera.
(10) AUTO FOCUS
Adjust the focus automatically.
(11) SHUTTLE
WHEEL
- Turn the shuttle wheel clockwise to zoom in and counter-clockwise to zoom out
the image optically and digitally in Camera and Playback mode only.
When it exceeds the maximum optical zoom level of about 12X, you may still
continue to AVer Optical zoom up to 1.66X AVerZoom and 8X digitally zoom.
Press ENTER to return to normal view (100%). The zoom bar indicator will turn
from blue to aqua to indicate that you can pan around the image.
- Press the shuttle wheel ▲,▼,◄, & ► to pan the image while in digital zoom
mode, to make a selection on 16-thumbnail images or move to the next or
previous single full screen preview in Playback mode, or to make a selection or
adjustment on the OSD main-menu and sub-menu (See Menu Functions for
more details).
12
ENGLISH
Name
Function
(12) MENU
Pull up and exit the OSD main-menu and sub-menu.
(13) PC1 and PC2
Indicator
Indicate the selected RGB IN video source either in RGB IN 1 or RGB IN 2.
(14) Video Output
LED Indicator
Indicate the setting of the Video Output switch to which the video signal is being
sent out.
Using AVerVision SPB350+ as a Mass Storage
This enables you to transfer the captured image to and from the memory source and PC.
You MUST read and follow the instructions below BEFORE connecting the USB cable.
Every time when using the SPB350+ as Mass Storage, the following MUST be done:
1. Select the memory source.
To select the memory source, press MENU > select SETTING >
MEMORY > SOURCE > EMBEDDED or SD and press ENTER;
then press MENU to exit.
2. MUST set the USB CONNECTION as MASS STORAGE.
To set the USB connection type, press MENU > select SETTING
> USB CONNECTION > MASS STORAGE and press ENTER;
then press MENU to exit.
3. When “MASS STORAGE” appears at the lower left corner of the
presentation screen, you may now connect the USB cable (See
“Connecting a Computer via USB Connection” for illustration).
4. Upon connecting the USB cable, the system automatically
detects the new removable disk.
5. In the Removable Disk dialog box, select Open folder to view files
and then click OK. You may now transfer the file to and from
your PC hard disk.
13
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
PLAYBACK OSD
14
NO
YES
PROFILE 1
PROFILE 2
PROFILE 3
SINGLE
CONTINUOUS
START
PAUSE
STOP
SET TIME
MODE
MANUAL FOCUS
IMAGE
LANGUAGE
MEMORY
USB CONNECTION
SAVE
LOWER LEFT
UPPER LEFT
UPPER RIGHT
LOWER RIGHT
VERTICAL
HORIZONTAL
SPOTLIGHT OFF
VISOR
OFF
SHADE
COLOR
RESIZE
ON
OFF
COLOR
B/W
NEGATIVE
684
800
5 SECS
CAPTURE
SAVE
PROFILE 1
PROFILE 2
PROFILE 3
USB CONNECTION
USB CAMERA
MASS STORAGE
MEMORY
SOURCE
FORMAT
LANGUAGE
ENGLISH
ESPAÑOL
日本語
繁體中文
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
0
MANUAL FOCUS
MODE
TEXT
GRAPHICS
HIGH FRAME
MICROSCOPE
140
16
NO
YES
EMBEDDED
SD CARD
63
255
800 x 600
1024 x 768
1280 x 960
1600 x 1200
1280 x 720
1920 x 1080
HD 720p 60 Hz
HD 1080p 60 Hz
HD 720p 50Hz
HD 1080p 50Hz
0
0
AUTO
RED
BLUE
AUTO
MANUAL
FLICKER
NIGHT VIEW
0
0
65
BLUE
65
RED
255
255
NIGHT VIEW
ON
OFF
FLICKER
50 HZ
60 HZ
21
MANUAL
ENGLISH
OSD Navigation Tree
VIDEO OUTPUT OSD
For TV output, RESOLUTION is not included in the menu list.
ENGLISH
Menu Functions
The MENU functions of SPB350+ enhance fine-tuning your screen display, set the timer, select OSD language
and more. Press the MENU button to call up and exit from the main menu or sub-menu display. Then use
▲or▼ buttons to select the items in the menu list. Use
►/ ENTER button to enter sub-menu and ◄/ ENTER
to return to main menu. To adjust the setting, press
◄or► buttons. To make a selection, press ENTER.
OSD Menu
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
Description
COLOR
B/W
NEGATIVE
ON
OFF
SPOTLIGHT OFF
VISOR
OFF
SHADE
COLOR
RESIZE
EFFECT
Press ► and use ▲or▼ buttons to select and display the image in Camera mode
into positive (true color), monochrome (black and white) or negative. Then press
►/ENTER to make a selection.
MIRROR
Press ► and use ▲or▼ buttons to select turning on/off MIRROR to flip the image
in Camera mode. Then press ►/ENTER to make a selection.
PRESENTER
Press ► and use ▲or▼ buttons to select and turn on either SPOTLIGHT or
VISOR. Then press ►/ENTER to make a selection. Only one feature can be used
at a time.
SPOTLIGHT overlays a frame on the presentation screen. Selecting SHADE
changes the opacity of the area outside the box from 0%, 50% and 100%, COLOR
to change the frame color from red, green and blue, and RESIZE to change the
size of the frame. To resize or move the frame around the presentation screen,
press the shuttle wheel ▲,▼,◄, & ►.
VISOR covers part of the presentation screen. The upper part of the presentation
screen is slightly exposed when it is being called each time. To expose part of the
covered area, press the shuttle wheel ▲,▼,◄, & ►. Se lect SHADE to change the
darkness of the shaded area between 50% or 100%.
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
VERTICAL
HORIZONTAL
SPLIT SCREEN
Press ► and use ▲or▼ buttons to select dividing the screen either vertically or
horizontally. Then press ►/ENTER to make a selection.
This function divides the screen into two parts. One side displays the live image
from the SPB350+ camera and the other side displays the captured images from
the memory source in 8-thumbnail preview.
Use the ▲,▼,◄, &► buttons to make a selection and ENTER to enlarge the
selected image in split screen mode. To horizontally or vertically pan the enlarged
image, use the ◄ & ► or ▲or▼ buttons.
15
ENGLISH
OSD Menu
Description
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
PIP
Press ► and use ▲or▼ buttons to select the location of the mini playback screen.
Then press ►/ENTER to make a selection.
Display a thumbnail of the captured image from the memory source at the corner of
the screen while in Camera mode.
Use ◄ or ► buttons to move to the previous or next image and ENTER to display
the image in full screen.
LOWER LEFT
UPPER LEFT
UPPER RIGHT
LOWER RIGHT
SETTING
Press ►, then use ▲or▼ buttons to select the items in SETTING list and press
►/ENTER.
M ENU
EFF ECT
M IRR OR
PRESE NT ER
SP LIT SCREE N
PI P
SE TTING
TIM ER
CAPTUR E
RE CALL
DEFAULT
MO DE
M ANUAL FOC US
IM AGE
M EMO RY
USB CONN ECT ION
SAV E
MODE
TEXT
GRAPHICS
HIGH FRAME
MICROSCOPE
SETTING > MODE
Use ▲or▼ buttons to select between Text, Graphics and High Frame enhancement
mode and then ENTER to make a selection.
MANUAL FOCUS
0
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
684
800
SETTING > IMAGE > EXPOSURE
Press ► and use ▲or▼ buttons to select between Auto, Manual, Flicker and Night
View. Then press ►/ENTER to make a selection.
Select AUTO to automatically adjust the camera exposure to determine how much
light is required.
AUTO
MANUAL
FLICKER
NIGHT VIEW
MANUAL
0
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
21
54
SETTING > IMAGE > EXPOSURE > FLICKER
Use ▲or▼ buttons to select between 50Hz or 60Hz. Some display devices cannot
handle high refresh rates. The image will flicker a couple of times as the output is
switched to another refresh rate.
NIGHT VIEW
ON
OFF
SETTING > IMAGE > EXPOSURE > NIGHT VIEW
Use ▲or▼ buttons to turn Night View ON or OFF.
If you are presenting in a low-light condition, Night View enables the image of the
object to appear as though under normal lighting conditions.
SPB350+ can automatically adjust the exposure to compensate for the adverse
condition, but the captured image will appear to be in slow motion.
SETTING > IMAGE > WHITE BALANCE
Press ► and use ▲or▼ buttons to select between auto or manually adjust the red
and blue color to suit the lighting condition or color temperature. Then press
►/ENTER to make a selection.
RED
65
255
SETTING > IMAGE > WHITE BALANCE > RED
Use ►or◄ buttons to manually adjust the red color level then press ENTER to
save the setting and exit.
255
SETTING > IMAGE > WHITE BALANCE > BLUE
Use ►or◄ but tons to manually adjust the blue color level then press ENTER to
save the setting and exit.
BLUE
0
SETTING > IMAGE > EXPOSURE > MANUAL
Use ►or◄ buttons to manually adjust the exposure level then press ENTER to
save the setting and exit.
FLICKER
50 HZ
60 HZ
AUTO
RED
BLUE
0
• Text - corrects the intensity of the adjacent pixel making it more uniform
producing sharper and clearer images.
• Graphics - adjusts the gradient of the adjacent pixel making it appears to have a
smooth image.
• High Frame - increases the frame rate capture and can visually tracks the motion
and react quickly. Sufficient lighting is required when using this mode.
• Microscope - automatically fixes the optical zoom and displays the microscope
image more clearly.
SETTING > MANUAL FOCUS
Use ◄or► buttons to manually adjust the focus and then press ENTER to save the
setting and exit.
65
16
ENGLISH
OSD Menu
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
Description
SETTING > IMAGE > BRIGHTNESS
Use ►or◄ buttons to increase or decrease the brightness level and improve the
visibility of the image. The brightness level can be set up to 63.
0
16
63
SETTING > IMAGE > CONTRAST
Use ►or◄ buttons to emphasize or reduce the difference between light and dark
conditions. The contrast level can be adjustable up to 255.
0
140
255
800 x 600
1024 x 768
1280 x 960
1600 x 1200
1280 x 720
1920 x 1080
HD 720p 60 Hz
HD 1080p 60 Hz
HD 720p 50Hz
HD 1080p 50Hz
LANGUAGE
ENGLISH
ESPAÑOL
日本語
繁體中文
MEMORY
SOURCE
FORMAT
MEMORY
SOURCE
FORMAT
SETTING > IMAGE > RESOLUTION
Press ► and use ▲or▼ buttons to choose from different display resolutions then
press ►/ENTER to make the selection.
This selection will not be available in TV output (Composite/S-Video)
SETTING > LANGUAGE
Use ▲or▼ buttons to select from different languages then press ►/ ENTER to
make the selection.
EMBEDDED
SD CARD
NO
YES
SETTING > MEMORY
Use ▲or▼ buttons to select either SOURCE or FORMAT.
• SOURCE – select the image storage in Camera mode or the source of the image
to display in Playback mode either in the built-in memory or SD card.
• FORMAT – select NO to exit or YES to format and delete all the images saved in
the memory source then press ►/ENTER.
Please wait till the message “FORMAT” disappear to finish the process.
USB CONNECTION
USB CAMERA
MASS STORAGE
SETTING > USB CONNECTION
Use ▲or▼ buttons to select the USB function between USB Camera an d Mass
Storage.
• USB Camera - can be used as a computer webcam or with our bundled software
as video recorder and capture still image.
• Mass Storage - transfer the captured images from the memory source to
computer hard disk.
SAVE
PROFILE 1
PROFILE 2
PROFILE 3
SETTING > SAVE
Use ▲or▼ but tons to select which user setting profile number to save your
preferred setting. Only effect, mode, brightness and contrast SETTING can be
saved.
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
TIMER
Press ► and use ▲or▼ buttons to select SET TIME to set the time value, START
to begin the countdown timer, PAUSE/RESUME to temporarily halt or continue, and
STOP to end.
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
START
PAUSE
STOP
SET TIME
SINGLE
CONTINUOUS
INTERVAL
5 SECS
CAPTURE
Press ► and use ▲or▼ buttons to select SINGLE or CONTINUOUS capture
mode. Then press ►/ENTER to make a selection.
• SINGLE saves one still image only.
• CONTINUOUS saves successive still images until the memory source is full or
when the CAP/DEL button is being press again to stop.
Use ►or◄ buttons to increase or decrease the capture time interval between
frames and then press ENTER to save the setting and exit. The time interval can
be set from 5 to 600 sec.
17
ENGLISH
OSD Menu
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
Description
RECALL
Press ►and use ▲or▼ buttons to select from the list to change to the preferred
saved user setting profile number then press ►/ENTER to make the selection.
PROFILE 1
PROFILE 2
PROFILE 3
MENU
EFFECT
MIRROR
PRESENTER
SPLIT SCREEN
PIP
SETTING
TIMER
CAPTURE
RECALL
DEFAULT
DEFAULT
Press ► and use ▲or▼ buttons to select YES to restore to original factory default
setting or NO to exit then press ►/ENTER to make the selection.
NO
YES
Technical Specifications
Image
Sensor
Total Pixel Count
Frame Rate
White Balance
Exposure
Theme
Effect
1/2.5” CMOS color image sensor
S-Video, Composite Video Output
Image Capture
Built-In Memory
5 mega pixels
30 fps (max)
Auto / Manual
Auto / Manual / Flicker / Night View
Text / Graphics / High Frame / Microscope
Color / BW / Negative
SVGA, XGA, 1280 x 960, UXGA, HD720, HD1080
(DVI-I supports reduced blanking only)
NTSC or PAL
Up to 240 Frames (2M)
32MB NAND Flash Memory
Shooting Area
AVer Optical Zoom
Digital Zoom
300mm x 225mm
20x
Digital 8x
Power Source
AC/DC100-240V, 50-60 Hz
16 watts (lamp on); 13.6 watts (lamp off) ;
14.6 watts (light box on)
Analog RGB Output
Optics
Power
Consumption
Lighting
Overhead light
Light box
LED Lamp
LED Lamp
Input/Output
RGB Input (2X)
RGB Output
DVI-I Output
S-Video Output
Video Output
USB
RS-232
15-Pins D-sub (VGA)
15-Pins D-sub (VGA)
DVI-I Type
Mini-DIN Jack
RCA Jack
USB2.0
9-Pins D-sub
Dimension
Fully Unfolded
Folded
480mm x 380mm x 505mm
480mm x 380mm x 150mm
Weight
5.6 kg (about 12.32 lb)
Card Supported
Secure Digital (SD)
16MB~2GB
18
ENGLISH
Using the RS-232 Interface
AVerVision SPB350+ can be controlled using a computer or any centralized control panel through RS-232
connection. The command code for RS-232 is provided for the system integrator to be able to incorporate it
with the system program.
RS-232C Dia g ram Connection
SPB350+ can be controlled using a PC through RS-232 connection.
DC 12V
RS-232
RGB IN 2
RGB IN 1
RGB OUT
IOIOI
Computer
RS-232 cable
(not supplied)
Laptop
RS-232C Cable Spec
Make sure the RS-232 cable matches the cable spec design.
19
ENGLISH
FUNCTION
AF
NEAR
FAR
ZOOM IN
ZOOM OUT
ZOOM RESET
FREEZE
ROTATE
MIRROR
EFFECT
BRT UP
BRT DOWN
AUTO IMAGE
TIMER
PROFILE
CAPTURE / DELETE
SPLIT SCRN
PIP
SPOTLIGHT ON / OFF
VISOR ON / OFF
SPOTLIGHT COLOR
SPOTLIGHT RESIZE
SPOTLIGHT / VISORVISOR SHADE
DATA CODE
0x0D
0x30
0x31
0x2D
0x2E
0x2F
0x0C
0x0E
0x2C
0x2B
0x29
0x2A
0x0A
0x0F
0x10
0x0B
0x11
0x13
0x23
0x24
0x25
0x26
0x27
CHECKSUM CODE
0x5A
0x67
0x66
0x7A
0x79
0x78
0x5B
0x59
0x7B
0x7C
0x7E
0x7D
0x5D
0x58
0x47
0x5C
0x46
0x44
0x74
0x73
0x72
0x71
0x70
Set Value Format:
Send Format 0x52 + 0x0B + 0x03 + Data[0] + Data[1] + Data[2] + 0x53 + CheckSum
Receive Format 0x53 + 0x00 + 0x01 + 0x0B + 0x53 + 0x59(ChkSum)
Function
Data[0]
Data[1]
Data[2]
CheckSum Code
Flicker 50Hz
0x00
0x00
0x00
0x5B
Flicker 60Hz
0x00
0x01
0x00
0x5A
Exposure Value
0x01
Value[0 ~ 95]
0x00
*1
WB Red Value
0x02
0x00
Value[0~255]
*1
WB Blue Value
0x02
0x01
Value[0~255]
*1
Brightness Value
0x03
Value[0 ~ 63]
0x00
*1
Contrast Value
0x04
Value[0 ~ 255]
0x00
*1
Rotate
0 degree
0x06
0x00
0x00
0x5D
Rotate 90 degree
0x06
0x01
0x00
0x5C
Rotate 180 degree
0x06
0x02
0x00
0x5F
Rotate 270 degree
0x06
0x03
0x00
0x5E
Effect Color
0x07
0x00
0x00
0x5C
Effect B/W
0x07
0x01
0x00
0x5D
Effect Negative
0x07
0x02
0x00
0x5E
Mode Text
0x08
0x00
0x00
0x53
Mode Graphics
0x08
0x01
0x00
0x52
Mode High Frame
0x08
0x02
0x00
0x51
Mode Microscope
0x08
0x03
0x00
0x50
SPLIT SCRN VERTICAL
0x0B
0x00
0x00
0x50
SPLIT SCRN HORIZONTAL
0x0B
0x01
0x00
0x51
PIP LOWER LEFT
0x0C
0x00
0x00
0x57
PIP UPPER LEFT
0x0C
0x01
0x00
0x56
PIP UPPER RIGHT
0x0C
0x02
0x00
0x55
PIP LOWER RIGHT
0x0C
0x03
0x00
0x54
20
ENGLISH
Function
Data[0]
Data[1]
Data[2]
CheckSum Code
CAPTURE SINGLE
0x0D
0x00
0x00
0x56
CAPTURE CONTINUOUS
0x0D
0x01
0x00
0x57
*1
CheckSum = 0x0B xor 0x03 xor Data[0] xor Data[1] xor Data[2] xor 0x53
Get Value Format:
Send Format 0x52 + 0x0A + 0x01 + Data[0] + 0x53 + CheckSum
Receive Format 0x53 + 0x0C + 0x01 + ReData[0] + 0x53 + ReCheckSum
Function
Data[0]
CheckSum Code
ReData[0]
ReCheckSum Code
Red Value
0x02
0x5A
Value[0~255]
*1
Blue Value
0x03
0x5B
Value[0~255]
*1
Lamp Status
0x05
0x5D
*1
Display Status
0x06
0x5E
0 : OFF 1: ON
0: Camera Mode
1: Playback Mode
2: PC-1 Pass
Through
3: PC-2 Pass
Through
*1
Video Output
Status
Freeze Status
0x07
0x5F
0: VGA 1: TV
*1
0x08
0x50
0 : OFF
*1
Brightness Value
0x0A
0x52
Value[0~63]
1: ON
Contrast Value
0x0B
0x53
Value[0~255]
LIGHT BOX
0x0C
0x54
0 : OFF 1: ON
Status
*1 ReCheckSum = 0x0C xor 0x01 xor ReData[0] xor 0x52
*1
*1
*1
Troubleshooting
This section provides useful tips describing how to solve common problems while using the AVerVision
SPB350+.
There is no picture on the presentation screen.
1.
2.
3.
4.
5.
Check all the connectors again as illustrated in this manual.
Check the remote control’s on/off switch on your display output device.
Verify the setting of the display output device.
If you are using a notebook or computer, you may have to switch the source to VGA.
Make sure the TV/RGB switch is properly set based on your display output.
There is no computer signal on the presentation screen.
When you turn on the computer, it will auto-detect the type of monitor you have. During auto-detection, there
won’t be any display on your presentation screen. To avoid this problem, connect your computer and all the
necessary cables to the AVerVision SPB350+ first before you power on your computer.
Unable to capture and save still image or is not responding.
- The message “FULL” is displayed. It means the memory source has reached the maximum capacity. Just
transfer the images to PC or format the memory source.
- The message “SD PROTECT” is displayed. It means the SD card is write protected. Just remove the SD
card from the slot and unlock it.
- The Capture setting could be in Continuous mode and the time interval is very long. Press MENU > select
Capture > Single or change the Continuous mode interval setting.
The picture on the presentation screen is distorted or the image is blurry.
- If the image is blurry or out of focus, press the Auto Focus button to automatically adjust the focus.
- If the Auto Focus button does not work and still unable to adjust the focus, the lens motor must be
misaligned. Unplug and plug the power to realign the lens motor.
21
ENGLISH
Limited War ranty
For a period of time beginning on the date of purchase of the applicable product and extending as set forth in the
“Warranty Period of AVer Product Purchased” section of the warranty card, AVer Information Inc. (“AVer”) warrants
that the applicable product (“Product”) substantially conforms to AVer’s documentation for the product and that its
manufacture and components are free of defects in material and workmanship under normal use. “You” as used in this
agreement means you individually or the business entity on whose behalf you use or install the product, as applicable.
This limited warranty extends only to You as the original purchaser. Except for the foregoing, the Product is provided “AS
IS.” In no event does AVer warrant that You will be able to operate the Product without problems or interruptions, or that
the Product is suitable for your purposes. Your exclusive remedy and the entire liability of AVer under this paragraph
shall be, at AVer’s option, the repair or replacement of the Product with the same or a comparable product. This
warranty does not apply to (a) any Product on which the serial number has been defaced, modified, or removed, or (b)
cartons, cases, batteries, cabinets, tapes, or accessories used with this product. This warranty does not apply to any
Product that has suffered damage, deterioration or malfunction due to (a) accident, abuse, misuse, neglect, fire, water,
lightning, or other acts of nature, commercial or industrial use, unauthorized product modification or failure to follow
instructions included with the Product, (b) misapplication of service by someone other than the manufacturer’s
representative, (c) any shipment damages (such claims must be made with the carrier), or (d) any other causes that do
not relate to a Product defect. The Warranty Period of any repaired or replaced Product shall be the longer of (a) the
original Warranty Period or (b) thirty (30) days from the date of delivery of the repaired or replaced product.
Limitations of Warranty
AVer makes no warranties to any third party. You are responsible for all claims, damages, settlements, expenses, and
attorneys’ fees with respect to claims made against You as a result of Your use or misuse of the Product. This warranty applies
only if the Product is installed, operated, maintained, and used in accordance with AVer specifications. Specifically, the
warranties do not extend to any failure caused by (i) accident, unusual physical, electrical, or electromagnetic stress, neglect or
misuse, (ii) fluctuations in electrical power beyond AVer specifications, (iii) use of the Product with any accessories or options
not furnished by AVer or its authorized agents, or (iv) installation, alteration, or repair of the Product by anyone other than AVer
or its authorized agents.
Disclaimer of Warranty
EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, AVER DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO THE PRODUCT, WHETHER
EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION, SATISFACTORY QUALITY,
COURSE OF DEALING, TRADE USAGE OR PRACTICE OR THE IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS.
Limitation of Liability
IN NO EVENT SHALL AVER BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, PUNITIVE, OR
CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, DATA,
REVENUE, PRODUCTION, OR USE, BUSINESS INTERRUPTION, OR PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES ARISING OUT OF OR IN CONNECTION WITH THIS LIMITED WARRANTY, OR THE USE OR PERFORMANCE
OF ANY PRODUCT, WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE, OR ANY OTHER LEGAL
THEORY, EVEN IF AVER HAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AVER’S TOTAL, AGGREGATE
LIABILITY FOR DAMAGES OF ANY NATURE, REGARDLESS OF FORM OF ACTION, SHALL IN NO EVENT EXCEED THE
AMOUNT PAID BY YOU TO AVER FOR THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.
Governing Law and Your Rights
This warranty gives You specific legal rights; You may also have other rights granted under state law. These rights vary from
state to state.
For warranty period, please refer to the warranty card.
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement