"user manual"

"user manual"
Short Pole Type
Bench Type
Bakery Type
User’s Manual
Hanging Type
Elevated Type
Self-service Type
Pole Type
Ver. 0.00
IMPORTANT
 Read this manual thoroughly, and do not perform installation,
operation, maintenance, or inspection unless you fully
understand all of the contents.
 Keep this manual in a safe place where you can refer to it easily
while installing, operating, and carrying out maintenance or
inspections.
RS-61004-11 1.02
© ISHIDA Co., Ltd. 2013
All rights are reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means
mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA.
RS-61004-11 1.02
NOTICES
NOTICES
IMPORTANT NOTICE
Those who handle the machine must be aware of the hazards involved. These dangers may not be obvious,
so it is imperative to follow the instructions detailed in this manual when installing, operating, inspecting, or
servicing the machine. Therefore, we recommend that you thoroughly read and understand this manual before
installing, operating, inspecting, or servicing the machine.
ISHIDA is not liable for any damage, loss or injury that results from incorrect operation, insufficient caution,
unauthorized modifications to the machine, or failure to follow the instructions contained in this manual.
LIMITATIONS OF LIABILITY
ISHIDA assumes no responsibility for special, indirect, or consequential damages, loss of profits or commercial
loss in any way connected with the machine, whether such claim is based on contract, warranty, negligence, or
strict liability.
ISHIDA assumes no responsibility for the user's programming of this machine, or any consequence thereof.
In no event shall ISHIDA be responsible for warranty, repair, or other claims regarding the machine unless
ISHIDA’s analysis confirms that the machines were properly handled, stored, installed, and maintained and not
subject to contamination, abuse, misuse, or inappropriate modification or repair.
CHANGE IN SPECIFICATIONS
Machine specifications and accessories may be changed at any time due to improvements or other reasons.
Consult with your ISHIDA representative at any time to confirm the actual specifications of the purchased
machine.
ERRORS AND OMISSIONS
The information in this manual has been carefully checked and is believed to be accurate; however, no
responsibility is assumed for clerical, typographical or proofreading errors, or omissions.
UNI-9 User’s Manual
iii
PRECAUTIONS FOR SAFE USE
PRECAUTIONS FOR SAFE USE
It is strongly advised that the following safety measures must be observed to ensure the safe operation of the
machine.
 Prepare a dedicated power source and always use a
power supply with rated voltage. Never connect the
machine power input with an AC power supply
exceeding the rated voltage. To avoid any potential
electrical shock, ensure that the protective ground
wire is connected to the main grounding provision.
A power supply that generates voltage variation may
cause a malfunction, or using the machine outside of the
rated voltage may result in machine failure or danger
such as electric shock.
 Do not install the machine near a TV set or radio.
Doing so may cause static to the TV set and/or radio as
this machine emits week electric wave.
 Do not allow water or any liquids to come into
contact with the machine.
Doing so may result in fire or cause the machine to break
down.
 Do not drop or apply a strong shock to the machine.
Doing so may cause the machine to break down.
 Do not disassemble, modify, or attempt to repair the
machine.
Doing so may damage the original safety functions.
UNI-9 User’s Manual
iv
PRECAUTIONS FOR SAFE USE
 Do not hold the connector cover when carrying the
machine.
Dropping the machine may result in injury or cause the
machine to break down.
 Do not hold the operation panel or weigh platter
when carrying the machine.
Doing so may cause the operation panel or the platter to
break down.
 Do not hold the pole type display when carrying the
machine.
Dropping the machine may result in injury or cause the
machine to break down.
 Handle with care when removing or inserting the
cassette.
Careless cassette handling may result in injury or cause
the cassette to break down.
 Do not drop the cassette.
Dropping the cassette may result in injury or cause the
cassette to break down.
 Do not press the touch panel with an edged thing.
Doing so may scratch the panel and cause the machine
to break down.
UNI-9 User’s Manual
v
PRECAUTIONS FOR SAFE USE
 Risk of explosion if battery is replaced by an
incorrect type. Make sure to dispose of used
batteries according to the instructions.
UNI-9 User’s Manual
vi
PRECAUTIONS FOR SAFE USE
PRECAUTIONS FOR MACHINE INSTALLATION
Do not install the machine in the following types of places:
 Places subject to high
temperatures or high humidity
 Places exposed to direct sunlight
 Places where water or other
liquids are easily spilled on the
machine
 Places subject to excessive
vibration or unstable foundations
 Places exposed to direct cold air
from air conditioners or
refrigerators
 Places subject to a lot of dust or
dirt
 Places with large voltage
fluctuations
 Places where the floor or
foundation is unstable
UNI-9 User’s Manual
vii
PRECAUTION SYMBOLS
PRECAUTION SYMBOLS
This machine is manufactured for use according to proper procedures by a qualified person and only for the
purposes described in this manual. The following conventions are used to indicate and classify precautions
depending on the level of danger, or seriousness of potential injury. Always heed the information provided in
this manual. Failure to heed precautions can result in personal injury or property damage.
The following precaution symbols are used in this manual.
Indicates a potentially hazardous situation which, if not avoided, may result in serious
injury or death. Additionally, there may be significant property damage.
Indicates a potentially hazardous situation where, if not avoided, may result in minor or
moderate injury or in property damage.
Indicates reference information for operation.
Indicates the referred page for operation.
UNI-9 User’s Manual
viii
TABLE OF CONTENTS
TABLE OF CONTENTS
CHAPTER 1
BEFORE USE ...................................................................................................................... 1-1
1.1
SPECIFICATIONS ..................................................................................................................... 1-1
1.2
PART NAMES ............................................................................................................................ 1-2
1.3
LEVEL ADJUSTMENT ............................................................................................................... 1-3
1.4
LABEL / RECEIPT ROLL LOADING .......................................................................................... 1-4
1.5
REMOVING & REPLACING OF WEIGHING PLATTER ............................................................ 1-6
1.6
1.7
1.5.1
REMOVING THE WEIGHING PLATTER ....................................................................... 1-6
1.5.2
REPLACING THE WEIGHING PLATTER ...................................................................... 1-6
CLEANING OF THE MACHINE ................................................................................................. 1-7
1.6.1
CLEANING OF THE THEREMAL HEAD ....................................................................... 1-7
1.6.2
CLEANING OF THE LABEL SENSOR........................................................................... 1-8
1.6.3
CLEANING OF THE PRINT ROLLER AND PRISM ....................................................... 1-9
1.6.4
PRECAUTIONS WHEN USING CLEANING FLUIDS .................................................. 1-10
STARTING PROCEDURES......................................................................................................1-11
1.7.1
TURNING ON THE POWER .........................................................................................1-11
1.7.2
ZERO ADJUSTMENT .................................................................................................. 1-12
1.7.3
GETTING BACK TO THE INITIAL SCREEN................................................................ 1-12
CHAPTER 2
OPERATION MODE ............................................................................................................ 2-1
2.1
OPERATION MODE ENTRY / EXIT .......................................................................................... 2-1
2.2
SCREEN EXAMPLES FOR PRODUCT CATEGORIES ............................................................ 2-2
2.3
SALES OPERATIONS ............................................................................................................... 2-4
2.3.1
ISSUING LABELS FOR WEIGHING PRODUCTS ......................................................... 2-4
2.3.2
ISSUING LABELS FOR WEIGHING FIXED PRICE PRODUCTS ................................. 2-6
2.3.3
ISSUING LABELS FOR FIXED PRICE PRODUCTS ..................................................... 2-8
2.3.4
ISSUING LABELS FOR FIXED WEIGHT/UNIT PRICE PRODUCTS .......................... 2-10
2.3.5
ISSUING LABELS REQUIRING OPERATOR REGISTRATION .................................. 2-12
2.3.6
ISSUING RECEIPTS BY THE SAME OPERATOR ...................................................... 2-14
2.3.7
ISSUING RECEIPTS BY DIFFERENT OPERATORS.................................................. 2-20
2.3.8
VOIDING PRODUCT REGISTRATIONS ..................................................................... 2-26
2.3.9
ENTERING OR OVERWRITING TARE WEIGHTS ...................................................... 2-28
2.3.10 CHANGING UNIT PRICES .......................................................................................... 2-28
2.3.11 CHANGING FIXED PRICES ........................................................................................ 2-29
2.3.12 DISCOUNTING UNIT PRICES BY AMOUNT .............................................................. 2-29
2.3.13 DISCOUNTING UNIT PRICES BY PERCENTAGE ..................................................... 2-30
2.3.14 DISCOUNTING TOTAL PRICES BY AMOUNT ............................................................ 2-30
2.3.15 DISCOUNTING TOTAL PRICES BY PERCENTAGE...................................................... 31
2.3.16 CHANGING QUANTITIES .............................................................................................. 31
2.3.17 SPECIFYING THE NUMBER OF LABELS ..................................................................... 32
2.3.18 SELF-SERVICE OPERATIONS FOR WEIGHING PRODUCTS ..................................... 33
2.3.19 SELF-SERVICE OPERATIONS FOR FIXED PRICE PRODUCTS ................................. 34
2.3.20 ACCUMULATIONS THROUGH MANUAL ENTRY ......................................................... 35
UNI-9 User’s Manual
ix
TABLE OF CONTENTS
2.3.21 ACCUMULATIONS THROUGH WEIGHING PRODUCTS .............................................. 37
2.3.22 VOIDING REGISTRATIONS THROUGH MANUAL ENTRY ........................................... 39
2.3.23 VOIDING THROUGH WEIGHING PRODUCTS ............................................................. 41
2.3.24 SUBTRACTING TOTALS THROUGH MANUAL ENTRY ................................................ 43
2.3.25 SUBTRACTING TOTALS THROUGH WEIGHING PRODUCTS .................................... 45
2.3.26 ADDING TOTALS THROUGH MANUAL ENTRY ............................................................ 47
2.3.27 ADDING TOTALS THROUGH WEIGHING PRODUCTS ................................................ 49
CHAPTER 3
TOTAL MODE ..................................................................................................................... 3-1
3.1
TOTAL MODE ENTRY / EXIT .................................................................................................... 3-1
3.2
DAILY TOTALS .......................................................................................................................... 3-2
3.3
WEEKLY TOTALS ..................................................................................................................... 3-5
3.4
CUMULATIVE TOTALS ............................................................................................................. 3-6
3.5
TRACEABILITY TOTALS ........................................................................................................... 3-8
3.6
PRESET REPORTS .................................................................................................................. 3-9
3.7
TOTAL CLEAR......................................................................................................................... 3-10
CHAPTER 4
PROGRAM MODE ............................................................................................................... 4-1
4.1
PROGRAM MODE ENTRY / EXIT ............................................................................................ 4-1
4.2
PLU DATA.................................................................................................................................. 4-2
4.3
CAMPAIGN DATA .....................................................................................................................4-11
4.4
OPERATOR DATA ................................................................................................................... 4-13
4.5
PRESET KEY REGISTRATION ............................................................................................... 4-15
4.5.1
SETTING PRESET GROUPS AND PAGES ................................................................ 4-15
4.5.2
SETTING PRESET KEYS ............................................................................................ 4-16
4.5.3
CHANGING PRESET KEY SIZES AND POSITIONS .................................................. 4-18
4.5.4
EDITING PRESET KEYS ............................................................................................. 4-19
4.5.5
DELETING PRESET KEYS ......................................................................................... 4-24
4.6
ADVERTISEMENT MESSAGES ............................................................................................. 4-25
4.7
SCHEDULE DATA ................................................................................................................... 4-28
4.8
STORE DATA .......................................................................................................................... 4-30
4.9
DEPARTMENT NAME DATA ................................................................................................... 4-33
4.10 GROUP NAME DATA .............................................................................................................. 4-35
4.11 COOKING INSTRUCTION DATA ............................................................................................ 4-37
4.12 EXTRA MESSAGE DATA ........................................................................................................ 4-39
4.13 COUPON MESSAGE DATA .................................................................................................... 4-41
4.14 POP MESSAGE DATA ............................................................................................................ 4-43
4.15 SCHEME TABLE DATA ........................................................................................................... 4-45
4.16 GEN TABLE DATA ................................................................................................................... 4-49
4.17 LOOKUP TABLE DATA ............................................................................................................ 4-51
4.18 MINCE TRACEABILITY DATA ................................................................................................. 4-54
4.19 FIXED PRICE SYMBOLS ........................................................................................................ 4-55
4.20 FREE MESSAGE DATA .......................................................................................................... 4-57
UNI-9 User’s Manual
x
TABLE OF CONTENTS
4.21 CHECK LABEL DATA .............................................................................................................. 4-59
4.22 STAMP PRICE DATA............................................................................................................... 4-60
4.23 NUTRITION TEXT DATA ......................................................................................................... 4-61
CHAPTER 5
SETUP MODE ..................................................................................................................... 5-1
5.1
SETUP MODE ENTRY / EXIT ................................................................................................... 5-1
5.2
MACHINE NUMBER / NETWORK NUMBER ............................................................................ 5-2
5.3
SALES MODE ........................................................................................................................... 5-4
5.4
PASSWORD .............................................................................................................................. 5-5
5.5
KEY LOCK ................................................................................................................................. 5-8
5.6
DATA STORAGE ......................................................................................................................5-11
5.7
PRESET REPORT .................................................................................................................. 5-12
5.8
PLU OVERWRITE ................................................................................................................... 5-14
5.9
PLU INITIAL DATA................................................................................................................... 5-16
5.10 PLU UPDATE .......................................................................................................................... 5-24
5.11 RECEIPT SETTING................................................................................................................. 5-27
5.12 TAX REGISTRATION .............................................................................................................. 5-29
CHAPTER 6
ADJUSTMENT MODE ......................................................................................................... 6-1
6.1
ADJUSTMENT MODE ENTRY / EXIT ....................................................................................... 6-1
6.2
DATE / TIME .............................................................................................................................. 6-2
6.3
TOUCH SCREEN ...................................................................................................................... 6-4
6.4
DISPLAY CHECK ...................................................................................................................... 6-5
6.5
SOUND...................................................................................................................................... 6-6
APPENDIX
TEXT EDITING..................................................................................................................... A-1
A.1
EDIT SCREENS ........................................................................................................................ A-1
A.2
EDIT KEYS ................................................................................................................................ A-2
A.3
INPUT EXAMPLES.................................................................................................................... A-4
A.3.1
TEXT EDITING .............................................................................................................. A-4
A.3.2
FONT STYLE SELECTION ............................................................................................ A-5
A.3.3
LINE DATA DELETION .................................................................................................. A-6
A.3.4
DATA ERASE ................................................................................................................. A-7
A.3.5
DATA COPY ................................................................................................................... A-8
UNI-9 User’s Manual
xi
Chapter 1: BEFORE USE
1
BEFORE USE
1.1 specifications
UNIT
Weighing unit
ITEM
DESCRIPTIONS
Weighing capacity
6 kg specification: 0 to 3 kg / 1 g, 3 to 6 kg / 2 g
Weighting accuracy
1/3000
Operation panel unit
Display method
8.4 inch color TFT liquid crystal display with LED
backlight, Screen resolution SCGA (800 X 600 dots)
Customer display unit
Display method
(1) 7 inch color TFT liquid crystal display with LED backlight,
Screen resolution SCGA (800 X 600 dots)
(2) 12.1 inch color TFT liquid crystal display with LED
backlight, Screen resolution SCGA (800 X 600 dots)
Printer unit
Printing method
Direct thermal method
Thermal head
3 inches (960 dots) and 12 dots/mm
Printing speed
120 mm/second
Note: The printing speed may vary depending on the label
conditions.
Printing effective size
80 mm in width
Label roll size
Label width: 30 to 80 mm
Label length: 20 to 100 mm
Cassette unit
Label replacement
Front loading cassette
No. of cassettes
Up to 7 cassettes can be used.
Label roll size
Roll outside diameter: 100 mm max.
Paper core inside diameter: 40 mm 1 mm
Others
Power supply
100 to 240 VAC, 50/60Hz
Use conditions
Temperature: 0 to 40°C
Humidity: 20 to 85%, non-condensing.
Input / Output
LAN: 1 channel
USB: 4 channels
SD: 1 channel
Cash drawer: 1 channel
Uni-9 User’s Manual
1-1
Chapter 1: BEFORE USE
1.2 PART NAMES
Bench Type
Uni-9 User’s Manual
1-2
Chapter 1: BEFORE USE
1.3 Level Adjustment
Install the machine horizontally to use.
Be sure to turn off the power switch before placing the machine on a stable platform, and adjust the machine
inclination by turning the four level adjustment legs so that the bubble is located at the center of the level gauge.
Accurate measurements cannot be performed if it is not installed horizontally.
Uni-9 User’s Manual
1-3
Chapter 1: BEFORE USE
1.4 label / receipt roll Loading
1.
Pull out the cassette from the main body.
Before pulling out the cassette unit,
ensure that nothing is placed on
the weighing platter.
2.
Set a new roll around the roll holder and raise the roll stopper to fix the roll position.
Roll stopper
Label roll
3.
Roll holder
Thread the paper as shown in the figures below.
Label Threading
Receipt Threading
Uni-9 User’s Manual
1-4
Chapter 1: BEFORE USE
4.
For labels, fix the paper end with the backing paper stopper, and gently turn the winding bobbin
clockwise until the label becomes tight.
Winding bobbin
5.
Slide the label/receipt guide to help smooth paper feeding according to the paper width.
Label / Receipt guide
6.
Push the cassette straight into the main body to return to its original position.
 Before inserting the cassette unit
into the main body, ensure that
nothing sticks to the magnet on the
bottom of the cassette unit.
 Push the cassette slowly into the
main body so as not to get your
fingers caught.
7.
Press the [FEED] key to issue a label.
At this time, confirm that the label is completely peeled off.
Confirm that the backing paper is
wound up smoothly. If the backing
paper is wound up diagonally,
check that the label is set correctly.
Label
Uni-9 User’s Manual
1-5
Chapter 1: BEFORE USE
1.5 removing & replacing of weighing platter
1.5.1
REMOVING THE WEIGHING PLATTER
When removing the weighing platter from the main body, lift the front side to pull out the two pins from the two
rubber platter holders and remove the platter by pulling it to disengage the two hooks at the rear side of the
platter.
1.5.2
REPLACING THE WEIGHING PLATTER
When replacing the weighing platter onto the main body, engage the two hooks at the rear side of the platter
and lower the platter so that the two pins on the bottom of the platter are inserted into holes of the rubber
platter holders.
Uni-9 User’s Manual
1-6
Chapter 1: BEFORE USE
1.6 Cleaning of the machine
1.6.1
1.
CLEANING OF THE THEREMAL HEAD
Pull out the cassette from the main body.
Before pulling out the
cassette unit, ensure that
nothing is placed on the
weighing platter.
2.
Use a cotton-tipped swab to clean off the thermal head.
Uni-9 User’s Manual
1-7
Chapter 1: BEFORE USE
1.6.2
1.
CLEANING OF THE LABEL SENSOR
Pull out the cassette from the main body.
Before pulling out the cassette
unit, ensure that nothing is
placed on the weighing platter.
2.
Use a dry cloth to clean off the emitter and receiver of the label sensor.
Uni-9 User’s Manual
1-8
Chapter 1: BEFORE USE
1.6.3
1.
CLEANING OF THE PRINT ROLLER AND PRISM
Pull out the cassette from the main body.
Before pulling out the cassette
unit, ensure that nothing is
placed on the weighing platter.
2.
Use a dry cloth to clean off the print roller and prism.
Uni-9 User’s Manual
1-9
Chapter 1: BEFORE USE
1.6.4
PRECAUTIONS WHEN USING CLEANING FLUIDS
Use a soft cloth and a neutral detergent to clean the machine.
Do not use thinner, benzene, etc. Doing so may damage the original safety functions.
For some parts, use cleaning fluid (isopropyl alcohol).
 Do not use cleaning fluid near fire as the fluid is flammable.
 Do not use cleaning fluid in a poorly ventilated area. Always provide adequate
ventilation when cleaning.
Take the following actions in the event of an accident:
If the fluid gets in your eye
 Immediately wash your eye(s) with water for at least 15 minutes, and consult your doctor.
 If you wear contact lenses, remove and wash them.
If the fluid comes into contact with your skin
 Immediately rinse the area of contact with water, and then wash with soap.
 If you notice any skin abnormalities at the area of contact, or if any pain persists, consult your
doctor.
If the fumes of the fluid are inhaled
 Immediately move the victim to an area where fresh air is available, and have the victim lie down
and keep warm.
 If breathing becomes difficult or stops, provide artificial respiration and seek medical attention
immediately.
If the fluid is swallowed
 Do not try to induce vomiting.
 Do not give the victim anything to drink, and do not rinse the mouth.
 If vomiting occurs naturally, have the victim lean forward to reduce risk of aspiration.
 Keep the victim warm and seek medical attention.
Uni-9 User’s Manual
1-10
Chapter 1: BEFORE USE
1.7
STARTING PROCEDURES
1.7.1
1.
TURNING ON THE POWER
Push down the Power Switch to turn on the
power.
2.
The “Clock Check” screen is displayed.
Check that displayed date and time agree
with the current date and time, and press the
[ENTER] button on the screen to proceed to
the next step.
Note: Refer to the “Date/Time” menu in Adjustment
Mode when changing date or time.
3.
The initial screen is displayed.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
Uni-9 User’s Manual
1-11
Chapter 1: BEFORE USE
1.7.2
1.
If the “ZERO” indicator does not appear in the
“WEIGHT” field on the initial screen, press
the [ZERO] key.
1.7.3
1.
ZERO ADJUSTMENT
2.
The “ZERO” indicator lights up and the
weight value becomes zero.
GETTING BACK TO THE INITIAL SCREEN
To get back to the initial screen from a Menu
selection screen, press the [SALES] button”
at the bottom right on the screen.
Uni-9 User’s Manual
2.
The initial screen is displayed.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
1-12
Chapter 2: OPERATION MODE
2
OPERATION MODE
2.1
OPERATION MODE ENTRY / EXIT
Ensure that the initial screen is displayed.
Then, press the Return button to display the
“Menu” screen.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
The “Menu” screen is displayed.
Note: To exit the Operation Mode, press the [SALES] button.
UNI-9 User’s Manual
2-1
Chapter 2: OPERATION MODE
2.2
SCREEN EXAMPLES FOR PRODUCT CATEGORIES
Weighing Products
Weighing Fixed Price Products
UNI-9 User’s Manual
2-2
Chapter 2: OPERATION MODE
Non-weighing Fixed Price Products
Non-weighing Fixed Weight/Unit Price Products
UNI-9 User’s Manual
2-3
Chapter 2: OPERATION MODE
2.3
SALES OPERATIONS
2.3.1
ISSUING LABELS FOR WEIGHING PRODUCTS
1.
Press the “SALES” icon on the operation
menu selection screen.
The initial screen is displayed.
2.
Enter a PLU number and press the [PLU] key
on the keypad.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
Note: If “ZERO” is not indicated on the screen, press
[0] on the keypad.
EXAMPLE
OR
Press a preset product department key to
display the associated screen.
EXAMPLE
“FRUITS” department
PLU No.3
1
2
2
Then, press the preset PLU key where the
product is assigned.
EXAMPLE
product)
UNI-9 User’s Manual
“Red Grape” (weighing
2-4
Chapter 2: OPERATION MODE
3.
The designated weighing PLU screen is
displayed.
4.
Put the product on the weighing platter.
EXAMPLE
A product to which its unit price and tare
weight were set beforehand.
The product is weighed and its total price is
calculated.
5.
Press the [PRINT] key to issue a label when
“MANUAL” is set in the “Print Mode” field.
Note: A label is automatically issued when “AUTO” is
set in the “Print Mode” field.
Non-traceable products
UNI-9 User’s Manual
Traceable products
2-5
Chapter 2: OPERATION MODE
2.3.2
ISSUING LABELS FOR WEIGHING FIXED PRICE PRODUCTS
1.
Press the “SALES” icon on the operation
menu selection screen.
The initial screen is displayed.
2.
Enter a PLU number and press the [PLU] key
on the keypad.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
Note: If “ZERO” is not indicated on the screen, press
[0] on the keypad.
EXAMPLE
OR
Press a preset product department key to
display the associated screen.
EXAMPLE
department
“VEGETABLES”
PLU No.29
1
2
2
3
Then, press the preset PLU key where the
product is assigned.
EXAMPLE
product)
UNI-9 User’s Manual
“ANISE” (weighing
2-6
Chapter 2: OPERATION MODE
3.
The designated weighing PLU screen is
displayed.
4.
Put the product on the weighing platter.
EXAMPLE
A product to which its tare weight and price
were set beforehand.
The product is weighed, but its price stays
the same.
5.
Press the [PRINT] key to issue a label when
“MANUAL” is set in the “Print Mode” field.
Note: A label is automatically issued when “AUTO” is
set in the “Print Mode” field.
Non-traceable products
UNI-9 User’s Manual
Traceable products
2-7
Chapter 2: OPERATION MODE
2.3.3
ISSUING LABELS FOR FIXED PRICE PRODUCTS
1.
Press the “SALES” icon on the operation
menu selection screen.
2.
Enter a PLU number and press the [PLU] key
on the keypad.
Note: If “ZERO” is not indicated on the screen, press
[0] on the keypad.
EXAMPLE
The initial screen is displayed.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
OR
Press a preset product department key to
display the associated screen.
EXAMPLE
“FRUITS” department
PLU No.4
1
2
2
Press the preset PLU key where the product
is assigned.
EXAMPLE
“Apple Royal” (non-weighing product)
UNI-9 User’s Manual
2-8
Chapter 2: OPERATION MODE
3.
The designated non-weighing PLU screen is
displayed.
4.
Press the [PRINT] key to issue labels when
“MANUAL” is set in the “Print Mode” field.
Note: Labels are automatically issued when “AUTO”
is set in the “Print Mode” field.
Non-traceable products
Traceable products
Note: To stop printing, press the [PRINT] key again.
UNI-9 User’s Manual
2-9
Chapter 2: OPERATION MODE
2.3.4
ISSUING LABELS FOR FIXED WEIGHT/UNIT PRICE PRODUCTS
1.
Press the “SALES” icon on the operation
menu selection screen.
2.
Enter a PLU number and press the [PLU] key
on the keypad.
Note: If “ZERO” is not indicated on the screen, press
[0] on the keypad.
EXAMPLE
The initial screen is displayed.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
OR
Press a preset product department key to
display the associated screen.
EXAMPLE
department
“VEGETABLES”
PLU No.27
2
1
3
2
Press the preset PLU key where the product
is assigned.
EXAMPLE
“BROCCOLI” (non-weighing product)
UNI-9 User’s Manual
2-10
Chapter 2: OPERATION MODE
3.
The designated non-weighing PLU screen is
displayed.
4.
Enter the fixed weight and press the “FIXED
WEIGHT” field.
EXAMPLE Fixed weight “159 g”
3
4
2
1
5.
Non-traceable products
Traceable products
Note: To stop printing, press the [PRINT] key again.
UNI-9 User’s Manual
2-11
Chapter 2: OPERATION MODE
2.3.5
ISSUING LABELS REQUIRING OPERATOR REGISTRATION
1.
Press the “SALES” icon on the operation
menu selection screen.
The initial screen is displayed.
2.
Enter a PLU number and press the [PLU] key
on the keypad.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
Note: If “ZERO” is not indicated on the screen, press
[0] on the keypad.
EXAMPLE
OR
Press a preset product department key to
display the associated screen.
EXAMPLE
“FRUITS” department
PLU No.3
1
2
2
Press the preset PLU key where the product
is assigned.
EXAMPLE
product)
UNI-9 User’s Manual
“Red Grape” (weighing
2-12
Chapter 2: OPERATION MODE
3.
The designated PLU screen is displayed.
EXAMPLE
A product to which its unit price and tare
weight were set beforehand.
4.
Put the product on the weighing platter.
The product is weighed and its total price is
calculated.
5.
Press an operator button to issue a label.
EXAMPLE Operator “BETTY”
Non-traceable products
UNI-9 User’s Manual
Traceable products
2-13
Chapter 2: OPERATION MODE
2.3.6
1.
ISSUING RECEIPTS BY THE SAME OPERATOR
Ensure that the “Operator Selection” screen
is displayed.
Then, press an operator button for selection.
The initial screen is displayed.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
EXAMPLE Operator “BETTY”
2.
Enter a PLU number and press the [PLU] key
on the keypad.
Note: If “ZERO” is not indicated on the screen, press
[0] on the keypad.
EXAMPLE
OR
Press a preset product department key to
display the associated screen.
EXAMPLE
“FRUITS” department
PLU No.3
1
2
2
Press a preset PLU key where the product is
assigned.
EXAMPLE
product)
UNI-9 User’s Manual
“Red Grape” (weighing
2-14
Chapter 2: OPERATION MODE
3.
The designated weighing PLU screen is
displayed.
Put the product on the weighing platter.
4.
Press the [SUB TOTAL] key to complete the
registration.
The subtotal screen for the designated
operator appears on the screen.
5.
Select a product department by pressing the
corresponding field.
EXAMPLE
“FRUITS” department
6.
The PLU preset key screen associated to the
designated department is displayed.
Then, press the preset PLU key where the
product is assigned.
EXAMPLE
“APPLE ROYAL” (fixed price product)
UNI-9 User’s Manual
2-15
Chapter 2: OPERATION MODE
7.
8.
Press [] to complete the registration.
Select a product department by pressing the
corresponding field on the screen.
EXAMPLE
department.
9.
“VEGETABLES”
The PLU preset key screen associated to the
designated department is displayed.
Then, press the preset PLU key where the
product is assigned.
EXAMPLE
“ANISE” (weighing product)
The PLU screen is displayed.
UNI-9 User’s Manual
10.
Put the product on the weighing platter.
2-16
Chapter 2: OPERATION MODE
11.
12.
The subtotal screen for the designated
operator is displayed.
Press the [SUB TOTAL] button.
Select a product department by pressing the
corresponding field on the screen.
EXAMPLE
“VEGETABLES”
department.
13.
The PLU preset key screen associated to the
designated department is displayed.
Then, press the preset PLU key where the
product is assigned.
EXAMPLE
“BROCCOLI” (fixed unit price product)
1
2
3
The designated PLU screen is displayed.
14.
Enter the weight, and press the “Fixed
Weight” field on the screen.
EXAMPLE
Weight “159g”
3
4
UNI-9 User’s Manual
2
1
2-17
Chapter 2: OPERATION MODE
15.
16.
Press the [SUB TOTAL] button.
The subtotal screen is displayed.
Press the operator field to display more
detailed subtotal data.
The detailed subtotal screen is displayed.
Then, confirm that the details of the
displayed transaction are correct.
UNI-9 User’s Manual
17.
2-18
Chapter 2: OPERATION MODE
18.
Press the [PRINT] key to issue a receipt.
UNI-9 User’s Manual
The subtotal screen is displayed.
2-19
Chapter 2: OPERATION MODE
2.3.7
1.
2.
ISSUING RECEIPTS BY DIFFERENT OPERATORS
Ensure that the initial screen is displayed.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
Enter a PLU number and press the [PLU] key
on the keypad.
Note: If “ZERO” is not indicated on the screen, press
[0] on the keypad.
EXAMPLE
OR
Press a preset product department key to
display the associated screen.
EXAMPLE
“FRUITS”
PLU No.3
1
2
2
Then, press the preset PLU key where the
product is assigned.
EXAMPLE
product)
UNI-9 User’s Manual
“Red Grape” (weighing
2-20
Chapter 2: OPERATION MODE
3.
5.
6.
The designated PLU screen is displayed.
4.
Press an operator button.
EXAMPLE
EXAMPLE
The subtotal screen for the designated
operator is displayed.
Operator “BETTY”
Select a product department by pressing the
corresponding field on the screen.
“FRUITS” department.
Put the product on the weighing platter.
7.
The PLU preset screen associated to the
designated department is displayed.
Then, press the preset PLU key where the
product is assigned.
EXAMPLE
“APPLE ROYAL” (fixed price product)
UNI-9 User’s Manual
2-21
Chapter 2: OPERATION MODE
The designated PLU screen is displayed.
The subtotal screen for the designated
operator is displayed.
8.
9.
Press an operator button.
EXAMPLE
Now, the operator has changed from
“BETTY” to “JACK”.
Select a product department by pressing the
corresponding field on the screen.
EXAMPLE
department
10.
The PLU preset screen associated to the
designated department is displayed.
Then, press the preset PLU key where the
product is assigned.
Operator “BETTY”
“VEGETABLES”
The designated PLU screen is displayed.
EXAMPLE
“ANISE” (weighing product)
UNI-9 User’s Manual
2-22
Chapter 2: OPERATION MODE
11.
Put the product on the weighing platter.
Press an operator button.
EXAMPLE
The subtotal screen for the designated
operator is displayed.
12.
Now, “BETTY” is back again.
Select a product department by pressing the
corresponding field on the screen.
EXAMPLE
department
13.
The PLU preset screen associated to the
designated department is displayed.
Then, press the preset PLU key where the
product is assigned.
Operator “JACK”
“VEGETABLES”
The designated PLU screen is displayed.
EXAMPLE
“BROCCOLI” (fixed unit price product)
UNI-9 User’s Manual
2-23
Chapter 2: OPERATION MODE
14.
Enter the weight value, and press the “Fixed
Weight” field.
EXAMPLE
16.
Press an operator button.
EXAMPLE
Operator “BETTY”
Weight “159 g”
3
2
4
1
The subtotal screen for the designated
operator is displayed.
17.
16.
Press the operator field to display more
detailed subtotal data.
The detailed subtotal screen is displayed.
Then, confirm that the details of the
transaction are correct.
UNI-9 User’s Manual
2-24
Chapter 2: OPERATION MODE
18.
Press the [PRINT] key to issue a receipt.
UNI-9 User’s Manual
The subtotal screen is displayed.
2-25
Chapter 2: OPERATION MODE
2.3.8
1.
VOIDING PRODUCT REGISTRATIONS
To void a product registration that has been
made in the transaction, display the
“Sub-Total” screen.
2.
Press the field of a product registration to be
voided, and then press the [VOID] button.
EXAMPLE
registration
Voiding the third
2
1
Note: To scroll the selection up or down, press the
[] or [] keys.
3.
The confirmation screen is displayed.
Then, press [EXEC] to continue, or [STOP] to
go back.
UNI-9 User’s Manual
The designated product registration has been
voided.
2-26
Chapter 2: OPERATION MODE
4.
Press the [PRINT] key to issue a receipt.
The subtotal screen is displayed.
Deleted by a dashed line
UNI-9 User’s Manual
2-27
Chapter 2: OPERATION MODE
2.3.9
1.
ENTERING OR OVERWRITING TARE WEIGHTS
Ensure that the designated PLU screen is
displayed.
2.
Enter a numerical value and press the
[T] (Tare) key.
EXAMPLE
Tare weight “50 g”
3
1
2
2.3.10
1.
CHANGING UNIT PRICES
Ensure that the designated PLU screen is
displayed.
2.
Enter the unit price and press the “UNIT
PRICE” field.
EXAMPLE
“$1.56”
4
2 3
1
UNI-9 User’s Manual
2-28
Chapter 2: OPERATION MODE
2.3.11
1.
CHANGING FIXED PRICES
Ensure that the designated PLU screen is
displayed.
2.
Enter the price, and press the “FIXED
PRICE” field.
EXAMPLE
“$1.56”
Fixed Price Products
4
2 3
1
2.3.12
1.
DISCOUNTING UNIT PRICES BY AMOUNT
Ensure that the designated PLU screen is
displayed.
2.
Enter the amount to be discounted, and
press the “-$ (U/P)” field.
EXAMPLE
Discount amount “$0.50”.
1
2
3
UNI-9 User’s Manual
2-29
Chapter 2: OPERATION MODE
2.3.13
1.
DISCOUNTING UNIT PRICES BY PERCENTAGE
Ensure that the designated PLU screen is
displayed.
2.
Enter the discount percentage, and press the
“-% (U/P)” field.
EXAMPLE
“10%”.
Discount percentage
1
3
2.3.14
1.
2
DISCOUNTING TOTAL PRICES BY AMOUNT
Ensure that the designated PLU screen is
displayed.
2.
Enter a discount amount using the numeric
keys, and press the “-$” field.
EXAMPLE
Discount amount “$0.50”.
1
3
2
UNI-9 User’s Manual
2-30
Chapter 2: OPERATION MODE
2.3.15
1.
DISCOUNTING TOTAL PRICES BY PERCENTAGE
Ensure that the designated PLU screen is
displayed.
2.
Enter the discount percentage, and press the
“-%” field.
EXAMPLE
“10%”.
Discount percentage
3
2.3.16
1.
1
2
CHANGING QUANTITIES
Ensure that the designated price PLU screen
is displayed.
2.
Enter the quantity and press the [X] key.
EXAMPLE
Quantity “3 pieces”
1
2
UNI-9 User’s Manual
2-31
Chapter 2: OPERATION MODE
2.3.17
1.
SPECIFYING THE NUMBER OF LABELS
Ensure that the designated PLU screen is
displayed, and confirm that “AUTO” is
selected in the “Print Mode” field.
2.
Enter the number of labels to be printed and
press the [PRINT] key to print labels. .
EXAMPLE
“3 labels”
2
1
Note:
To interrupt the issue of labels, press the [PRINT]
key again.
To restart the issue of labels, press the [PRINT] key
again.
UNI-9 User’s Manual
2-32
Chapter 2: OPERATION MODE
2.3.18
1.
SELF-SERVICE OPERATIONS FOR WEIGHING PRODUCTS
Ensure that the initial screen for self-service
operations is displayed.
2.
Select a product by pressing the
corresponding field on the screen.
EXAMPLE
product)
3.
The designated product image is displayed.
4.
“Red Grape” (weighing
Put the product on the weighing platter.
The product is weighed and its total price is
calculated.
5.
Press the [PRINT] button to issue a label.
UNI-9 User’s Manual
2-33
Chapter 2: OPERATION MODE
UNI-9 User’s Manual
2-34
Chapter 2: OPERATION MODE
2.3.19
1.
SELF-SERVICE OPERATIONS FOR FIXED PRICE PRODUCTS
Ensure that the initial screen for self-service
operations is displayed.
2.
Select a product by pressing the
corresponding field on the screen.
EXAMPLE
3.
The designated product image is displayed.
“APPLE ROYAL”
Enter the quantity and press the [MULTI] key.
Then, press the [PRINT] key to issue a label.
EXAMPLE
3 pieces
2
1
UNI-9 User’s Manual
3
2-35
Chapter 2: OPERATION MODE
2.3.20
ACCUMULATIONS THROUGH MANUAL ENTRY
1.
Ensure that the operation menu selection
screen is displayed.
Then, press the “ACC (Accumulation)” icon.
The “Input Numerical Accumulation” screen
is displayed.
2.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
The “Input Numerical Accumulation” screen
for the designated product is displayed.
EXAMPLE
PLU No.3
2
3
1
3.
Enter the quantity, weight, and price to be
accumulated and press the applicable fields.
Then, press the [ACC] button on the screen.
4.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
EXAMPLE
Quantity “1 pc.”, Weight “400g”, Price “$1.50”
UNI-9 User’s Manual
2-36
Chapter 2: OPERATION MODE
1
5.
2
3
4
The accumulation procedure has been
completed.
UNI-9 User’s Manual
2-37
Chapter 2: OPERATION MODE
2.3.21
1.
2.
ACCUMULATIONS THROUGH WEIGHING PRODUCTS
Ensure that the operation menu selection
screen is displayed.
Then, press the “ACC (Accumulation)” icon.
The “Input Numerical Accumulation” screen
is displayed.
Press the “WGT. ACC” tab to display the
“Weighing Accumulation” screen.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
3.
EXAMPLE
PLU No.3
2
3
1
The Weighing Accumulation screen for the
designated product is displayed.
UNI-9 User’s Manual
4.
Put the product on the weighing platter and
press the [ACC] button.
2-38
Chapter 2: OPERATION MODE
5.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
6.
Remove the product from the weighing
platter.
The accumulation procedure has been
completed.
2-39
Chapter 2: OPERATION MODE
2.3.22
1.
2.
VOIDING REGISTRATIONS THROUGH MANUAL ENTRY
Ensure that the operation menu selection
screen is displayed.
Then, press the “ACC (Accumulation)” icon.
The “Input Numerical Accumulation” screen
is displayed.
Press the “NUM. VOID” tab to display the
“Input Number Void” screen.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
3.
EXAMPLE
PLU No.3
2
3
1
The “Input Number Void” screen for the
selected product is displayed.
4.
Enter the quantity, weight, and price to be
voided and press the applicable fields.
Then, press the [VOID] button.
EXAMPLE
Quantity “1 pc.”, Weight “400g”, Price “$1.50”
4
1
UNI-9 User’s Manual
2
3
2-40
Chapter 2: OPERATION MODE
5.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
6.
The void procedure has been completed.
2-41
Chapter 2: OPERATION MODE
2.3.23
1.
2.
VOIDING THROUGH WEIGHING PRODUCTS
Press the “ACC (Accumulator)” icon.
The “Input Number Accumulation” screen is
displayed.
To display the “Weighing Void” screen, press
the “WGT. VOID” tab.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
3.
EXAMPLE
PLU No.3
2
2
3
1
The “Weighing Void” screen for the selected
product is displayed.
UNI-9 User’s Manual
4.
Put the product on the weighing platter and
press the [VOID] button on the screen.
2-42
Chapter 2: OPERATION MODE
5.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
6.
Remove the product from the weighing
platter.
The void procedure has been completed.
2-43
Chapter 2: OPERATION MODE
2.3.24
1.
2.
SUBTRACTING TOTALS THROUGH MANUAL ENTRY
Press the “TOTAL ADJUST” icon.
The “Total Adjust (Input Number
Subtraction)” screen is displayed.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
The Total Adjust (Input Number Subtraction)
screen for the selected product is displayed.
EXAMPLE PLU No.3
2
3
1
3.
Enter the quantity, weight, and price to be
subtracted and press the applicable fields.
Then, press the [SUB] button on the screen.
4.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
EXAMPLE
Quantity “1 pc.”, Weight “400g”, Price “$1.50”
2
1
UNI-9 User’s Manual
1
1
2-44
Chapter 2: OPERATION MODE
5.
The subtraction procedure has been
completed.
UNI-9 User’s Manual
2-45
Chapter 2: OPERATION MODE
2.3.25
1.
2.
SUBTRACTING TOTALS THROUGH WEIGHING PRODUCTS
Press the “TOTAL ADJUST” icon.
The “Total Adjust (Input Number
Subtraction)” screen is displayed.
To display the “Total Adjust (Weighing
Subtraction)” screen, press the “WGT. SUB”
tab.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
3.
EXAMPLE
PLU No.3
2
3
1
The “Total Adjust (Weighing Subtraction)”
screen for the selected product is displayed.
UNI-9 User’s Manual
4.
Put the product on the weighing platter and
press the [SUB] button.
2-46
Chapter 2: OPERATION MODE
5.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
6.
Remove the product from the weighing
platter to complete the subtraction procedure.
2-47
Chapter 2: OPERATION MODE
2.3.26
1.
2.
ADDING TOTALS THROUGH MANUAL ENTRY
Press the “TOTAL ADJUST” icon.
The “Total Adjust (Input Number
Subtraction)” screen is displayed.
To display the “Total Adjust (Input Number
Addition)” screen, press the “NUM. ADD” tab.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
3.
EXAMPLE
PLU No.3
2
3
1
The “Total Adjust (Input Number Addition)”
screen for the selected product is displayed.
4.
Enter the quantity, weight, and price to be
added and press the applicable fields.
Then, press the [ADD] button.
EXAMPLE
Quantity “1 pc.”, Weight “400g”, Price “$1.50”
1
UNI-9 User’s Manual
1
1
2
2-48
Chapter 2: OPERATION MODE
5.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
6.
The addition procedure has been completed.
2-49
Chapter 2: OPERATION MODE
2.3.27
1.
2.
ADDING TOTALS THROUGH WEIGHING PRODUCTS
Press the “TOTAL ADJUST” icon.
The “Total Adjust (Input Number
Subtraction)” screen is displayed.
To display the “Total Adjust (Weighing Add)”
screen, press the [WGT. ADD] tab.
Press the input field at the right-bottom of the
screen to display the keypad.
Then, enter a PLU number and press the
[PLU] key on the keypad.
3.
EXAMPLE
PLU No.3
2
3
1
The “Total Adjust (Weighing Add)” screen for
the selected product is displayed.
UNI-9 User’s Manual
4.
Put the product on the weighing platter and
press the [ADD] button.
2-50
Chapter 2: OPERATION MODE
5.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
6.
Remove the product from the weighing
platter to complete the addition procedure.
2-51
Chapter 3: TOTAL MODE
3
TOTAL MODE
3.1 total MODE ENTRY / exit
1.
Make sure that the initial screen is displayed.
Then, press the Return button on the screen
to display the “Menu” screen.
2.
Press the [TOTAL] button.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
The total menu selection screen is displayed.
Note: To exit the Total Mode, press the [SALES] button.
UNI-9 User’s Manual
3-1
Chapter 3: TOTAL MODE
3.2
DAILY TOTALS
1.
The total menu selection screen is
displayed.
2.
To display the “Production Daily Total
(Hourly)” screen, press the “HOUR” tab.
To turn pages, press [] or [].
The “Production Daily Total (Total)” screen
is displayed.
3.
To display the “Production Daily Total
(Department)” screen, press the “DEPT.”
tab.
2
1
UNI-9 User’s Manual
3-2
Chapter 3: TOTAL MODE
4.
To display the “Production Daily Total
(Group)” screen, press the “GROUP” tab.
6.
Press the input field at the right-bottom of
the screen to display the keypad.
Then, enter a desired PLU number and
press the [PLU] key on the keypad.
5.
To display the “Production Daily Total (PLU)”
screen, press the “PLU” tab.
EXAMPLE PLU No.3
2
3
1
7.
To display the “Production Daily Total
(Operator)” screen, press the “OPER.” tab.
UNI-9 User’s Manual
8.
To display the “Production Daily Total
(Type)” screen, press the “TYPE” tab.
3-3
Chapter 3: TOTAL MODE
9.
Select the target reports by pressing a
desired button.
10.
Select the listing order by pressing a desired
button.
No.
The total analysis is performed for all products.
DEPT.
The total analysis is performed for all departments.
GROUP
The total analysis is performed for all groups.
PLU No.
The total analysis is performed in ascending PLU number order.
ABC PRICE
The total analysis is performed in descending price order.
ABC WEIGHT
The total analysis is performed in descending weight order.
ABC PCS
The total analysis is performed in descending quantity order.
Z PRICE
The total analysis is performed in ascending price order.
Z WEIGHT
The total analysis is performed in ascending weight order.
Z PCS
The total analysis is performed in ascending quantity order.
UNI-9 User’s Manual
3-4
Chapter 3: TOTAL MODE
3.3
WEEKLY TOTALS
1.
Press the “PROD. WEEKLY” icon.
The Weekly Total (Week) screen is
displayed.
3.
To display the “Production Weekly Total” total
for the day-of-the week, press a desired
day-of-the week tab.
To turn pages, press the [] or [].
2
1
UNI-9 User’s Manual
3-5
Chapter 3: TOTAL MODE
3.4
CUMULATIVE TOTALS
1.
Press the “PROD. CUM. TOTAL” icon.
The “Cumulative Total (Total) screen is
displayed.
3.
To display total for departments, press the
“DEPT.” tab.
4.
To display total for groups, press the
“GROUP” tab.
5.
To display total for operators, press the
“OPER.” tab.
6.
To display analysis totals, press the “TYPE”
tab.
No.
The total analysis is performed for all products.
DEPT.
The total analysis is performed for all departments.
GROUP
The total analysis is performed for all groups.
PLU No.
The total analysis is performed in ascending PLU number order.
ABC PRICE
The total analysis is performed in descending price order.
ABC WEIGHT
The total analysis is performed in descending weight order.
ABC PCS
The total analysis is performed in descending quantity order.
UNI-9 User’s Manual
3-6
Chapter 3: TOTAL MODE
7.
Z PRICE
The total analysis is performed in ascending price order.
Z WEIGHT
The total analysis is performed in ascending weight order.
Z PCS
The total analysis is performed in ascending quantity order.
Select the target reports and listing order by
pressing desired buttons, and press the
[ANALYSIS] button.
1
2
3
UNI-9 User’s Manual
3-7
Chapter 3: TOTAL MODE
3.5
1.
TRACEABILITY TOTALS
Press the “TRACE. TOTAL” icon.
UNI-9 User’s Manual
For more information, refer to the Service
Manual for UNI-9.
3-8
Chapter 3: TOTAL MODE
3.6
PRESET REPORTS
1.
Press the “PRESET REPORT” icon.
2.
Select a desired report type by pressing the
corresponding fields.
Press the [PRINT] button to issue the
selected reports.
UNI-9 User’s Manual
The “Preset Report” screen is displayed.
3-9
Chapter 3: TOTAL MODE
3.7
TOTAL CLEAR
1.
Press the “TOTAL CLEAR” icon.
2.
Select desired reports to be cleared by
pressing the corresponding fields.
Then, press the [DELETE] button.
1
UNI-9 User’s Manual
The “Total Clear” screen is displayed.
3.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
2
3-10
Chapter 4: PROGRAM MODE
4
PROGRAM MODE
4.1 program MODE ENTRY / exit
1.
Ensure that the initial screen is displayed,
and press the Return button on the screen.
2.
The “Menu” screen is displayed.
Then, press the [PROGRAM] button.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
The program menu selection screen is
displayed.
To turn pages, press [] or [].
Note: To exit the Program Mode, press the [SALES] button.
UNI-9 User’s Manual
4-1
Chapter 4: PROGRAM MODE
4.2
PLU DATA
1.
Press the “PLU” icon on the menu selection
screen.
2.
Select a desired PLU by pressing the
corresponding field, and press the [DETAIL]
button.
The “PLU” screen is displayed.
To turn pages, press [] or [].
3.
The “PLU Detail (Sales)” screen is displayed.
To edit the PLU name, press the name field.
1
2
4.
The “PLU Name Edit” screen is displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
UNI-9 User’s Manual
5.
Press the “SALE 1” tab to display the “PLU
Detail (Sale 1)” screen.
The screen below shows that “Sales Mode”
is set for selling weighing products.
4-2
Chapter 4: PROGRAM MODE
Press [] or [] to select a desired sales mode.
0: Weight (for selling weighing products)
1: Fix price (for selling fixed price products)
2: Weight fix price (for selling weighing fixed price products)
SALES MODE
3: Fix unit price (for selling fixed unit price products)
4: Weight (100 g) (when the setting of the unit price per 100 g is needed in
accordance of the laws of a country)
5: Fix unit price (minus) (when the setting of the minus sale is needed in
accordance of the laws of a country)
UNIT PRICE /
FIXED PRICE
Enter the unit price or fixed price and press this field.
OPEN PRICE
Press [] or [] to select whether or not to allow an open price system.
0: Yes
FIXED WEIGHT
1: No
Enter the fixed weight and press this field.
TARE
Enter the tare weight and press this field.
TAX
Enter a numerical value and press this field.
M/D AMOUNT
Press [] or [] to select a desired markdown mode.
0: Normal price
1: Special price
2: Amount discount for total price
3: Percent discount for total price
4: Special unit price
5: Amount discount for unit price
6: Percent discount for unit price
Enter the markdown amount or percentage and press this field.
2nd TARE
Enter the tare weight, and press this field.
MARKDOWN MODE
UNI-9 User’s Manual
4-3
Chapter 4: PROGRAM MODE
Press the “UNIT TYPE” field to display the “Fix Price Symbol” screen.
Then, press a desired field for selection.
UNIT TYPE
6.
QTY
Enter the packed quantity and press this field.
TARE
Enter the tare percentage and press this field.
LOWER WEIGHT
Enter the lower weight limit and press this field.
UPPER WEIGHT
Enter the upper weight limit and press this field.
FORCED TARE
Press [Yes] or [No] button to select whether or not to use the forced tare
function.
Press the “SALE 2” tab to select the second sale related screen.
UNI-9 User’s Manual
4-4
Chapter 4: PROGRAM MODE
ITEM
DESCRIPTIONS
Press [] or [] to select whether or not to use the point flag.
POINT FLAG
0: OFF
1: ON
Press [] or [] to select a desired point type.
POINT TYPE
0: Weight
1: Fixed weight
POINTS
Enter a desired number and press this field.
7.
Press the “MSG.” tab to select the message
related screen.
9.
The “Extra Message” screen is displayed.
Press a desired field for selection.
10.
Press the “IMAGE” tab to display the “PLU /
Detail (Image)” screen.
UNI-9 User’s Manual
8.
Press a desired field for selection.
The selected message has been
registered.
11.
Press a desired field for selection.
4-5
Chapter 4: PROGRAM MODE
12.
14.
The “Image” screen is displayed.
Press a desired image for selection.
Press a desired display image field.
13.
The selected image has been registered.
Press [NO PRINT] or [PRINT] in the “Safe
Handling Image” field to select whether or
not to print the image.
15.
The Display Image screen is displayed.
Press a desired image for selection.
Note: To use images stored in the USB memory,
press [STORAGE] key. The movie file with the
format of MPEG-4, 800 x 600 (SVGA), 10 Mbps,
25 FPS can also be used.
Then, press the [SET] button.
UNI-9 User’s Manual
4-6
Chapter 4: PROGRAM MODE
16.
17.
The selected image has been registered.
Press [NO PRINT] or [PRINT] in the “Safe
Handling Image” field to select whether or
not to print the image.
Press the “PRINT” tab to display the PLU / Detail (Print) screen.
ITEM
1st LABEL FORMAT
No. (M)
2nd LABEL
FORMAT No.
1st LABEL FORMAT
No. (A)
1st LABEL PRINT
2nd LABEL PRINT
UNI-9 User’s Manual
DESCRIPTIONS
Enter a desired format number and press this field.
Enter a desired format number and press this field.
Enter a desired format number and press this field.
Press [  ] or [  ] to select whether or not to print the first label.
1: Yes
2: No
Press [  ] or [  ] to select whether or not to print the second label.
1: Yes
2: No
4-7
Chapter 4: PROGRAM MODE
18.
Press the “DATE” tab to display the PLU / Detail (Date) screen.
ITEM
PACK DATE PRINT
PACK TIME PRINT
PACK TIME DATA
UNI-9 User’s Manual
DESCRIPTIONS
Press [YES] or [NO] in this field to select whether or not to print the packed
date.
Press [] or [] to select a desired pack time printing method.
0: No print
1: Designated time
2: System clock time
This field is available only when “1: Designated time” is selected in “PACK
4-8
Chapter 4: PROGRAM MODE
SB DATE PRINT
SB TIME PRINT
SB TIME DATA
SHELF LIFE (days)
USE BY DATE PRINT
UB DATE DATA
19.
TIME PRINT”. Enter the time and press this field.
Press [YES] or [NO] in this field to select whether or not to print the sell-by
date.
Press [] or [] to select a desired sell-by time printing method.
0: No print
1: Designated time
2: Relative time
This field is available only when “Yes” is selected in “SB TIME PRINT”.
Enter the number of hours and press this field.
This field is available only when “Yes” is selected in “SB DATE PRINT”.
Enter the number of days and press this field.
Press [YES] or [NO] in this field to select whether or not to print the
use-by date.
This field is available only when “Yes” is selected in “USE BY DATE
PRINT”.
Enter the number of hours and press this field.
Press the “CODE” tab to select the PLU / Detail (Code) screen.
ITEM
ITEM CODE
UNI-9 User’s Manual
DESCRIPTIONS
Enter an item code and press this field.
4-9
Chapter 4: PROGRAM MODE
REG CODE
Enter the register code and press this field.
This field is available only when “1: PLU File” is selected in “POS
POS FLAG
REFERENCE”.
Enter a POS flag number and press this field.
BARCODE
Enter a barcode number and press this field.
Press [] or [] to select a desired reference method.
POS REFERENCE
0: Refer
1: PLU file
This field is available only when “1: PLU File” is selected in “POS
REFERENCE”.
Press this field to display the Barcode Type screen, and press a desired
PLU type for selection.
BARCODE TYPE
Press this field to display the Barcode Format screen, and press a
desired barcode format for selection.
POS FORMAT (WGT)
UNI-9 User’s Manual
4-10
Chapter 4: PROGRAM MODE
TRACE ENABLE
DEPARTMENT No.
GROUP No.
UNI-9 User’s Manual
Press [YES] or [NO] in this field to select whether or not to enable a
traceability function.
Press this field to display the Department screen.
To set a department, press a desired field on the list, or press the
“DEPARTMENT No.” field after numerical entry.
Press this field to display the Group screen.
To set a group, press a desired field on the list, or press the “GROUP
No.” field after numerical entry.
4-11
Chapter 4: PROGRAM MODE
4.3
1.
2-2
CAMPAIGN DATA
Press the “CAMPAIGN” icon on the menu
selection screen.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-1
2-3
The “Campaign” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Campaign / Detail (Data)” screen is
displayed.
Press the [CALL] button to call up the PLU
screen.
4-12
Chapter 4: PROGRAM MODE
5.
7.
The PLU screen is displayed.
Press a desired item field for selection.
The designated “Campaign / Detail (Data)”
screen is displayed.
Press the “MD MODE” field.
The Campaign / Mode List screen is
displayed.
Press a desired field for selection.
EXAMPLE
8.
6.
Percent discount “-%”
Press the “MD PRI” field to display the
keypad on the screen.
Enter a numerical value and press the [SET]
key on the key pad.
EXAMPLE 10%
1
2
3
4
UNI-9 User’s Manual
4-13
Chapter 4: PROGRAM MODE
UNI-9 User’s Manual
4-14
Chapter 4: PROGRAM MODE
4.4 OPerator data
1.
Press the “OPERATORS” icon on the menu
selection screen.
2.
The “Operator” screen is displayed.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
EXAMPLE Operator No.13
3
2
4
3.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
4.
1
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
2
1
5.
The “Operator / Detail” screen is displayed.
To register the operator name, press the name
field.
6.
The Operator / Detail Edit screen is displayed
for the designated operator number.
Edit text according to the procedure described
in Appendix “Text Editing”.
UNI-9 User’s Manual
4-15
Chapter 4: PROGRAM MODE
7.
To finish the editing, press the Return button.
8.
To set a password, press the Input field at the
bottom right of the screen to display the
keypad.
Enter the 4-digit numerical value and press the
[SET] key on the keypad, and then press the
“PASSWORD” field.
Enter
3
9.
Press the Return button to finish the editing.
UNI-9 User’s Manual
10.
1
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
4-16
Chapter 4: PROGRAM MODE
11.
The edited data has been registered.
UNI-9 User’s Manual
4-17
Chapter 4: PROGRAM MODE
4.5
PRESET KEY REGISTRATION
4.5.1
SETTING PRESET GROUPS AND PAGES
1.
Press the “PRESET KEY” icon on the menu
selection screen.
2.
The Preset Key screen is displayed.
Press a desired field for selection, and press
the [DETAIL] button.
1
2
3.
The edit screen is displayed.
Press [<] or [>] to select the group or page
number.
4.
To create or delete the group or the page,
press the [GROUP] or [PAGE] button, and
then press a desired function button as shown
below.
1
2
UNI-9 User’s Manual
4-18
Chapter 4: PROGRAM MODE
4.5.2
1.
SETTING PRESET KEYS
Press the “PRESET KEY” icon on the menu
selection screen.
2.
The “Preset Key” screen is displayed.
Press a desired field for selection, and press
the [DETAIL] button.
1
2
3.
Select the group and the page where you
want to add the preset key, and then press
the [KEY] button and then [NEW] button.
Available preset keys are listed on the screen.
To turn pages, press [] or [].
1
2
UNI-9 User’s Manual
4-19
Chapter 4: PROGRAM MODE
4.
5.
The PLU screen is displayed.
Press a desired field for selection.
6.
Press a desired function for selection.
EXAMPLE Selecting the PLU function
The selected preset key has been assigned.
EXAMPLE PLU No.3
UNI-9 User’s Manual
4-20
Chapter 4: PROGRAM MODE
UNI-9 User’s Manual
4-21
Chapter 4: PROGRAM MODE
4.5.3
1.
CHANGING PRESET KEY SIZES AND POSITIONS
Press the “PRESET KEY” icon on the menu
selection screen.
2.
The “Preset Key” screen is displayed.
Press a desired field for selection, and press
the [DETAIL] button.
1
2
3.
Select the group and the page that the preset
key you want to edit is located, and then
press [KEY] key, desired preset key, and
[SIZE] or [MOVE] key.
4.
The size and position editing screen is
displayed.
1
3
2
5.
Press either the [SIZE] or [MOVE] button.
6.
Set desired key size and position by using the
input fields and arrow buttons, followed by
pressing the [SET] key on the keypad.
1
2
UNI-9 User’s Manual
4-22
Chapter 4: PROGRAM MODE
4.5.4
1.
EDITING PRESET KEYS
Press the “PRESET KEY” icon on the menu
selection screen.
2.
The “Preset Key” screen is displayed.
Press a desired field for selection, and press
the [DETAIL] button.
1
2
3.
Select the group and the page that the preset
key you want to edit is located.
Then, press the [KEY] button, the preset key,
and the [EDIT] button.
4.
The editing screen is displayed.
1
3
2
5.
To split the preset key display into two
portions, press the “SPLIT” field, enter a
numerical value, and press the [SET] button
on the keypad.
6.
The preset key has been split.
1
Enter
3
UNI-9 User’s Manual
4-23
Chapter 4: PROGRAM MODE
7.
To change the font size, press the “TITLE
FONT” or ”FONT” field, enter a numerical
value, and press the [SET] button on the
keypad.
8.
The font size has been changed.
1
Enter
3
9.
To change the preset key title, press the
“TEXT EDIT” field.
10.
The “Preset Key / Name Edit” screen is
displayed.
Edit text according to the procedure described
in Appendix “Text Editing”.
11.
To finish the editing, press the Return button.
UNI-9 User’s Manual
12.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
4-24
Chapter 4: PROGRAM MODE
13.
To assign a desired image to the preset key,
press the “IMAGE No.” field.
14.
The Preset Key / Image screen is displayed.
Press a desired image for selection.
Note: To use images stored in the USB memory,
press [STORAGE] key. The movie file with the
format of MPEG-4, 800 x 600 (SVGA), 10 Mbps, 25
FPS can also be used.
Then, press the [SET] button.
1
15.
17.
The image has been assigned.
The Preset Key / Color screen is displayed.
UNI-9 User’s Manual
2
16.
To change the color of the preset key, press
the [COLOR] button.
18.
To change the background color, press either
the “UPPER BACKGROUND” or “LOWER
BACKGROUND” field.
4-25
Chapter 4: PROGRAM MODE
19.
Press a desired color for selection.
20.
21.
To change the font color, press the “UPPER
TEXT” or “LOWER TEXT” field.
22.
23.
The selected color has been applied to the
text on the key.
24.
UNI-9 User’s Manual
The selected color has been applied to the
background of the key.
Press a desired color for selection.
To change the preset key operation, press the
“FUNC No.” field.
4-26
Chapter 4: PROGRAM MODE
25.
Available functions are listed on the screen.
Press a desired function for selection.
27.
The PLU screen is displayed.
Then, press a desired field for selection.
29.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go back.
UNI-9 User’s Manual
26.
To change the PLU number called up by the
preset key, press the “DATA” field.
28.
Upon completion of all settings, press the Return
button.
4-27
Chapter 4: PROGRAM MODE
4.5.5
1.
DELETING PRESET KEYS
Press the “PRESET KEY” icon on the menu
selection screen.
2.
The “Preset Key” screen is displayed.
Press a desired field for selection, and press
the [DETAIL] button.
1
2
3.
Select the group and the page that the preset
key you want to delete is located.
Then, press the [KEY] button, preset key, and
the [DELETE] button.
4.
The selected key has been deleted.
1
3
2
UNI-9 User’s Manual
4-28
Chapter 4: PROGRAM MODE
4.6
1.
2-2
ADVERTISEMENT MESSAGES
Press the “AD MSG.” icon on the menu
selection screen.
2-1
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-3
The “Advertisement Message” screen is
displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Advertisement Message / Detail (Text)”
screen is displayed.
Press the name field.
4-29
Chapter 4: PROGRAM MODE
5.
The “Advertisement Message / Detail / Edit”
screen is displayed.
6.
To exit the edit mode, press the Return button.
Edit a desired message according to the
procedure described in Appendix “Text Editing”.
7.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
4-30
Chapter 4: PROGRAM MODE
8.
The “Advertisement Message / Detail (Text)” screen is displayed.
ITEM
DESCRIPTIONS
Press [] or [] to select a desired display type.
TEXT DISPLAY TYPE
0: None
1: Slide
2: Flash
Press [] or [] to select a desired display type.
IMAGE DISPLAY TYPE
0: None
1: Slide
2: Flash
Press [] or [] to select a desired display speed.
TEXT DISPLAY SPEED
0: Fast
1: Medium
2: Slow
DISPLAY COUNT
UNI-9 User’s Manual
Enter a display count data and press this field.
4-31
Chapter 4: PROGRAM MODE
9.
Press the “IMAGE” tab to display the
“Advertisement Message / Detail (Image)”
screen.
10.
Press a desired field to display the Image
screen.
11.
The “Advertisement Message / Image”
screen is displayed.
Press a desired image for selection.
12.
The selected image has been assigned in
the designated field.
Note: To use images stored in the USB memory,
press [STORAGE] key. The movie file with the
format of MPEG-4, 800 x 600 (SVGA), 10 Mbps, 25
FPS can also be used.
Then, press the [SET] button.
1
UNI-9 User’s Manual
2
4-32
Chapter 4: PROGRAM MODE
4.7
1.
SCHEDULE DATA
Press the “SCHEDULER” icon on the menu
selection screen.
2-1
To call up a desired data number, press the
Input field at the bottom right of the screen to
display the keypad.
Then, enter a desired numerical value and
press the [PLU] key on the keypad.
Enter
3
1
2-2
To change existing data, press a desired field
for selection and then the [DETAIL] button.
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
1
2
In this case, go to Step 4.
4.
The designated Scheduler / Detail
(Schedule) screen is displayed.
Press [<] or [>] to change the type.
5.
To enter the start date, press the “START
DATE” field, enter a numerical value, and press
the [SET] key on the keypad.
EXAMPLE
Start date “June 25, 2013”
1
Enter
3
UNI-9 User’s Manual
4-33
Chapter 4: PROGRAM MODE
6.
To enter the start time, press the “START
TIME” field, enter a numerical value, and
press the [SET] key on the keypad.
EXAMPLE
7.
EXAMPLE
Start time “08:00”
1
Enter
3
3
To enter the end time, press the “END TIME”
field, enter a numerical value, and press the
[SET] key on the keypad.
EXAMPLE
End date “June 27, 2013”
1
Enter
8.
To enter the end date, press the “END DATE”
field, enter a numerical value, and press the
[SET] key on the keypad.
9.
When “DLY / WLY” is set in the “SHEDULE
TYPE” field, press a desired day of the week
for selection.
End time “21:00”
1
Enter
3
UNI-9 User’s Manual
4-34
Chapter 4: PROGRAM MODE
4.8
1.
STORE DATA
Press the “STORE” icon on the menu
selection screen.
2-1
The “Store” screen is displayed.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
Enter
3
1
2-2
To change existing data, press a desired field
for selection and then the [DETAIL] button.
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
1
2
In this case, go to Step 4.
UNI-9 User’s Manual
4-35
Chapter 4: PROGRAM MODE
4.
6.
8.
The “Store / Detail” screen is displayed.
Press the name field.
Press the Return button to finish the editing.
The store name has been registered.
UNI-9 User’s Manual
5.
The “Store / Name Edit” screen is displayed
for the selected store number.
Edit text according to the procedure
described in Appendix “Text Editing”.
7.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
9.
To create or change the store address, press
the “Address” field.
4-36
Chapter 4: PROGRAM MODE
10.
12.
The “Store / Edit Address” screen is
displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
11.
13.
Press the Return button to finish the editing.
The store address has been registered.
4-37
Chapter 4: PROGRAM MODE
4.9 department name data
1.
2-2
Press the “DEPARTMENT” icon on the
menu selection screen.
2-1
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-3
The “Department” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and press the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Department / Edit” screen is displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
4-38
Chapter 4: PROGRAM MODE
5.
7.
Press the Return button to finish the editing.
6.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
The edited data has been registered.
UNI-9 User’s Manual
4-39
Chapter 4: PROGRAM MODE
4.10
1.
2-2
group name data
Press the “GROUP” icon on the menu
selection screen.
2-1
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-3
The “Group” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Group / Edit” screen is displayed.
Edit the text according to the procedure
described in Appendix “Text Editing”.
4-40
Chapter 4: PROGRAM MODE
5.
7.
Press the Return button to finalize the edited
text.
6.
The confirmation screen appears.
Press [EXEC] to continue, or [STOP] to go
back.
The edited data has been registered.
UNI-9 User’s Manual
4-41
Chapter 4: PROGRAM MODE
4.11
1.
2-2
cooking instruction data
Press the “COOKING TIME” icon on the
menu selection screen.
2-1
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-3
The “Cooking Time” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Cooking Time / Edit” screen is
displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
4-42
Chapter 4: PROGRAM MODE
5.
7.
Press the Return button to finish the editing.
The edited data has been registered.
6.
8.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
Press the Input field at the bottom right of the
screen to display the keypad.
Enter a numerical value via the keypad and
press the applicable field.
3
Enter
1
9.
The edited data has been registered.
UNI-9 User’s Manual
4-43
Chapter 4: PROGRAM MODE
4.12
1.
2-2
extra message data
Press the “EXTRA MSG.” icon on the menu
selection screen.
To call up a desired data number, press the
Input field at the bottom right of the screen to
display the keypad.
Then, enter a desired numerical value and
press the [PLU] key on the keypad.
2-1
2-3
The “Extra Message” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Extra Message / Edit” screen is
displayed.
Edit text according to the procedure described
in Appendix “Text Editing”.
4-44
Chapter 4: PROGRAM MODE
5.
7.
Press the Return button to finish the editing.
6.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
The edited data has been registered.
UNI-9 User’s Manual
4-45
Chapter 4: PROGRAM MODE
4.13
1.
2-2
coupon message data
Press the “COUPON MSG.” icon on the
menu selection screen.
2-1
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-3
The “Coupon Message” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Coupon Message / Edit” screen is
displayed.
Edit text according to the procedure described
in Appendix “Text Editing”.
4-46
Chapter 4: PROGRAM MODE
5.
7.
Press the Return button to finish the editing.
6.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
The edited data has been registered.
UNI-9 User’s Manual
4-47
Chapter 4: PROGRAM MODE
4.14
1.
2-2
pop message data
Press the “POP MSG.” icon on the menu
selection screen.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-1
2-3
The “POP Message” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “POP Message / Edit” screen is
displayed.
Edit text according to the procedure described
in Appendix “Text Editing”.
4-48
Chapter 4: PROGRAM MODE
5.
7.
Press the Return button to finish the editing.
6.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
The edited data has been registered.
UNI-9 User’s Manual
4-49
Chapter 4: PROGRAM MODE
4.15
1.
2-2
scheme table data
Press the “SCHEME TABLE” icon on the
menu selection screen.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-1
2-3
The “Scheme Table” screen is displayed.
To create the first data, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Scheme Table / Detail (Control)” screen is
displayed.
Press the name field.
4-50
Chapter 4: PROGRAM MODE
5.
7.
The “Scheme Table / Edit screen” is
displayed.
Edit text according to the procedure described
in Appendix “Text Editing”.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
6.
8.
Press the Return button to finish the editing.
The edited data has been registered.
4-51
Chapter 4: PROGRAM MODE
ITEM
DESCRIPTIONS
Press this field to select whether or not to use this lot number.
RETAIN LOT No.
0: No
1: Yes
PASSPORT FORMAT No.
Enter a numerical value and press this field.
ICON No.
Enter a numerical value and press this field.
LIFE OFFSET
Enter a numerical value and press this field.
Press this field to select whether or not to control the weight limit.
WEIGHT LIMIT CONTROL
0: No
1: Yes
Press this field to select whether or not to control the date limit.
DATE LIMIT CONTROL
0: No
1: Yes
LOSS %
Enter a numerical value and press this field
ITEM
DESCRIPTIONS
LOT/CARCASS
Enter a numerical value and press the applicable data field.
GTIN
Enter a numerical value and press the applicable data field.
WEIGHT
Enter a numerical value and press the applicable data field.
PASSPORT LOT START
Enter a numerical value and press the data field.
PASSPORT GTIN START
Enter a numerical value and press this data field.
UNI-9 User’s Manual
4-52
Chapter 4: PROGRAM MODE
9.
Upon completion of the table data registration,
press the Return button.
UNI-9 User’s Manual
10.
The edited data has been registered.
4-53
Chapter 4: PROGRAM MODE
4.16
GEN table data
1.
Press the “GEN TABLE” icon on the menu
selection screen.
2.
3.
Enter a numerical value, press the applicable
field, and press the [SET] key.
4.
The “GEN Table” screen is displayed.
Press a desired field for selection.
To change the text, press the [EDIT] button.
1
Enter
3
5.
The “GEN Table / Title Text Edit” screen is
displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
UNI-9 User’s Manual
6.
Press the Return button to exit the edit mode.
4-54
Chapter 4: PROGRAM MODE
7.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
8.
The edited data has been registered.
4-55
Chapter 4: PROGRAM MODE
4.17
1.
2-2
Lookup Table data
Press the “LOOKUP TABLE” icon on the
menu selection screen.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-1
2-3
The “Lookup Table” screen is displayed.
To create the first table, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Lookup Table / Name Edit” screen is
displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
4-56
Chapter 4: PROGRAM MODE
5.
7.
8-2
Press the Return button to finish the editing.
The edited text has been registered.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
6.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
8-1.
To create the first data, press the [NEW]
button.
8-3
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
Enter
2
3
1
UNI-9 User’s Manual
4-57
Chapter 4: PROGRAM MODE
9.
11.
The Lookup Data / Text Edit screen is
displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
10.
12.
Press the Return button to finish the editing.
The edited data has been registered.
4-58
Chapter 4: PROGRAM MODE
4.18
mince traceability data
1.
Press the "MINCE TRACE.” icon on the
menu selection screen.
2.
The “Mince Traceability” screen is displayed.
Press a desired field for selection.
3.
The keypad is displayed.
Enter a desired numerical value and press
the [SET] key.
4.
Press the Return button to complete the
procedure.
UNI-9 User’s Manual
4-59
Chapter 4: PROGRAM MODE
4.19
FixeD price symbols
1.
Press the "FIX PRICE SYMBOL” icon on the
menu selection screen.
2.
3.
Press the Input field at the bottom right of the
screen to display the keypad.
4.
The “Fix Price Symbol” screen is displayed.
Enter a desired table number and press the
[PLU] key on the keypad.
EXAMPLE Symbol No.6
1
2
5.
The “Fix Price Symbol / Edit” screen is
displayed.
6.
Press the Return button to finish the editing.
Edit text according to the procedure described
in Appendix “Text Editing”.
UNI-9 User’s Manual
4-60
Chapter 4: PROGRAM MODE
7.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
8.
The edited text has been registered.
To undo changes, press [CANCEL].
UNI-9 User’s Manual
4-61
Chapter 4: PROGRAM MODE
4.20
1.
2-2
free message data
Press the "FREE MSG.” icon on the menu
selection screen.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-1
2-3
The “Free Message” screen is displayed.
To create the first message, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Free Message Edit” screen is displayed.
Edit text according to the procedure described
in Appendix “Text Editing”.
4-62
Chapter 4: PROGRAM MODE
5.
Press the Return button to finish the editing.
6.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
7.
The edited data has been registered.
UNI-9 User’s Manual
4-63
Chapter 4: PROGRAM MODE
4.21
check label data
1.
Press the "CHECK LABEL” icon on the
menu selection screen.
3.
Enter the start number and the end number
via the keypad, and press the [SET] key.
2.
4.
The “Check Label” screen is displayed.
Press a desired field.
Press the [STRAT] button to print a label.
Enter
2
UNI-9 User’s Manual
4-64
Chapter 4: PROGRAM MODE
4.22
STAMP PRICE data
1.
Press the "STAMP PRICE” icon on the menu
selection screen.
3.
Enter the stamp price and the reference
price via the keypad, and press the [SET]
key.
2.
The “Stamp Price” screen is displayed.
Press a desired field for selection.
Enter
2
UNI-9 User’s Manual
4-65
Chapter 4: PROGRAM MODE
4.23
1.
2-2
nutrition text data
Press the "NUTRITION TEXT” icon on the
menu selection screen.
To call up desired data, press the Input field
at the bottom right of the screen to display
the keypad.
Then, enter a numerical value and press the
[PLU] key on the keypad.
2-1
2-3
The “Nutrition Text” screen is displayed.
To create the first text, press the [NEW]
button.
To change existing data, press a desired field
for selection and then the [DETAIL] button.
1
2
Enter
3
In this case, go to Step 4.
1
3.
If a non-registered item has been called, the
confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
4.
The “Nutrition Text / Detail” screen is
displayed.
To create a new text, press a desired field.
4-66
Chapter 4: PROGRAM MODE
5.
7.
The “Nutrition Text / Edit” screen is
displayed.
Edit text according to the procedure
described in Appendix “Text Editing”.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
6.
8.
Press the Return button to finish the editing.
The edited data has been registered.
4-67
Chapter 5: SETUP MODE
5
SETUP MODE
5.1 setup mode entry / Exit
1.
Ensure that the initial screen is displayed.
Then, press the Return button on the screen
to display the “Menu” screen.
2.
The “Menu” screen is displayed.
Then, press the [SETUP] button.
Note: The contents of the initial screen may differ
depending on the settings on your machine.
3.
The setup menu selection screen is displayed.
Note: To exit the Setup Mode, press the [SALES] button.
UNI-9 User’s Manual
5-1
Chapter 5: SETUP MODE
5.2
1.
2.
MACHINE NUMBER / NETWORK NUMBER
Press the “MACHINE No.” icon on the menu
selection screen.
The “Machine No. (Basic)” screen is
displayed.
Press a desired field for selection.
Enter a numerical value via the keypad and
press the [SET] key.
EXAMPLE Network No.9
3.
1
2
4.
Press a desired field for selection.
EXAMPLE Network No.9
UNI-9 User’s Manual
5.
The network number has been registered.
To finish the editing, press the Return button.
5-2
Chapter 5: SETUP MODE
6.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
UNI-9 User’s Manual
5-3
Chapter 5: SETUP MODE
5.3
1.
SALES MODE
Press the “SALES MODE” icon on the menu
selection screen.
2.
The “Sales Mode” screen is displayed.
Then, select a desired sales mode by
pressing the corresponding button.
EXAMPLE “With Operator”
3.
Press the Return button to complete the
procedure.
UNI-9 User’s Manual
5-4
Chapter 5: SETUP MODE
5.4
PASSWORD
1.
Press the “PASSWORD” icon on the menu
selection screen.
The “Password (Operate)” screen is
displayed.
2.
Press the “TOTAL” tab to display the
“Password (Total)” screen.
Press the “PROGRAM” tab to display the
“Password (Program)" screen.
To turn pages, press [] or [].
3.
2
1
UNI-9 User’s Manual
5-5
Chapter 5: SETUP MODE
4.
Press the “SETUP” tab to display the
“Password (Setup)” screen.
To turn pages, press [] or [].
2
1
5.
UNI-9 User’s Manual
Press the “ADJUST” tab to display the
“Password (Adjust)" screen.
5-6
Chapter 5: SETUP MODE
6.
Press the “PASSWORD” field to display the
keypad.
Enter a 6-digit password and press [SET] key
on the keypad.
7.
Select a desired mode by pressing the
corresponding tab, and press any selection
buttons to set whether or not to prompt the
operator for the password for each menu.
1
2
Enter
3
8.
1
Press the Return button to complete the
procedure.
UNI-9 User’s Manual
5-7
Chapter 5: SETUP MODE
5.5
1.
2.
KEY LOCK
Press the “KEY LOCK” icon on the menu
selection screen.
The “Key Lock (Display Key)” screen is
displayed.
Press the “FUNCTION KEY” tab to display
the “Key Lock (Function Key)” screen.
To turn pages, press [] or [].
2
1
UNI-9 User’s Manual
5-8
Chapter 5: SETUP MODE
UNI-9 User’s Manual
5-9
Chapter 5: SETUP MODE
3.
Press the “PASSWORD” field to display the
keypad.
Then, enter a 6-digit password and press the
[SET] key on the keypad.
4.
Select a desired key category by pressing the
corresponding tab, and press any selection
buttons to lock or unlock lock the key.
1
2
Enter
3
5.
1
Press the Return button to complete the
procedure.
UNI-9 User’s Manual
5-10
Chapter 5: SETUP MODE
5.6
1.
DATA STORAGE
Press the “DATA STORAGE” icon on the
menu selection screen.
The “Data Staorage (Total Add)” screen is
displayed.
To turn pages, press [] or [].
2.
3.
Press any selection buttons to set whether or
not to apply the total addition function for
each menu.
Press the Return button to complete the
procedure.
UNI-9 User’s Manual
5-11
Chapter 5: SETUP MODE
5.7
1.
PRESET REPORT
Press the “PRESET REPORT” icon on the
menu selection screen.
The “Preset Report (Daily)” screen is
displayed.
To turn pages, press [] or [].
2.
UNI-9 User’s Manual
Press the “WEEKLY” tab to display the
“Preset Report (Weekly)” screen.
5-12
Chapter 5: SETUP MODE
Press the “CUMULATIVE” tab to display the
“Preset Report (Cumulative)” screen.
To turn pages, press [] or [].
3.
2
1
Select a desired report type by pressing the
corresponding tab, and press any selection
buttons to set whether or not to print the total.
4.
5.
Press the Return button to complete the
procedure.
2
1
UNI-9 User’s Manual
5-13
Chapter 5: SETUP MODE
5.8
1.
PLU OVERWRITE
Press the “PLU OVERWRITE” icon on the
menu selection screen.
The “PLU Overwrite” screen is displayed.
To turn pages, press [] or [].
Note: Display items may vary depending on the
country setting.
2.
UNI-9 User’s Manual
Press any selection buttons to set whether or
not to overwrite the item automatically.
5-14
Chapter 5: SETUP MODE
3.
Press the Return button to complete the
procedure.
UNI-9 User’s Manual
5-15
Chapter 5: SETUP MODE
5.9
1.
PLU INITIAL DATA
Press the “PLU INITIAL DATA” icon on the
menu selection screen.
SALES MODE
UNIT PRICE /
FIXED PRICE
OPEN PRICE
FIXED WEIGHT
TARE
TAX
UNI-9 User’s Manual
The “PLU Initial Data (Sale 1)” screen is
displayed.
Press [] or [] to select a desired sales mode.
0: Weight (for selling weighing products)
1: Fix price (for selling fixed price products)
2: Weight fix price (for selling weighing fixed price products)
3: Fix unit price (for selling fixed unit price products)
Enter a unit price or fixed price and press this field.
Press [] or [] to select whether or not to allow an open price system.
0: Yes
1: No
Enter a fixed weight and press this field.
Enter a tare weight and press this field.
Enter a desired number and press this field.
5-16
Chapter 5: SETUP MODE
MARKDOWN MODE
M/D AMOUNT
2nd TARE
Press [] or [] to select a desired markdown mode.
0: Normal price
1: Special price
2: Amount discount for total price
3: Percent discount for total price
4: Special unit price
5: Amount discount for unit price
6: Percent discount for unit price
Enter a markdown amount or percentage and press this field.
Enter a tare weight, and press this field.
Press the “UNIT TYPE” field to display the “Fix Price Symbol” screen.
Then, press a desired field for selection.
UNIT TYPE
QTY
Enter the packed quantity and press this field.
TARE
Enter a tare percentage and press this field.
LOWER WEIGHT
Enter the lower weight limit and press this field.
UPPER WEIGHT
Enter the upper weight limit and press this field.
FORCED TARE
2.
Press [YES] or [NO] button to select whether or not to use the forced tare
function.
Press the “SALE 2” tab to display the “PLU Initial Data (Sale 2)” screen.
UNI-9 User’s Manual
5-17
Chapter 5: SETUP MODE
DESCRIPTIONS
Press [] or [] to select whether or not to use the point flag.
POINT FLAG
0: OFF
1: ON
Press [] or [] to select a desired point type.
POINT TYPE
0: Weight
1: Fixed weight
POINTS
Enter a desired number and press this field.
Press the “MSG.” tab to display the “PLU
Press a desired field for selection.
Initial Data (Message)” screen.
ITEM
3.
UNI-9 User’s Manual
4.
5-18
Chapter 5: SETUP MODE
5.
The “Extra Message” screen is displayed.
Press a desired field for selection.
The selected message has been registered.
6.
Press the “IMAGE” tab to display the “PLU
Initial Data (Image)” screen.
Press a desired field for selection.
UNI-9 User’s Manual
7.
5-19
Chapter 5: SETUP MODE
8.
10.
12.
The “Image” screen is displayed.
Press a desired image for selection.
Press the Display Image field.
9.
11.
The selected image has been registered.
Press [NO PRINT] or [PRINT] in the “Safe
Handling Image” field to select whether or
not to print the image.
The “Display Image” screen is displayed.
Press a desired image for selection.
Note: To use images stored in the USB memory,
press [STORAGE] key. The movie file with the
format of MPEG-4, 800 x 600 (SVGA), 10 Mbps, 25
FPS can also be used.
Then, press the [SET] button.
The selected image has been registered.
Press [NO PRINT] or [PRINT] in the “Safe
Handling Image” field to select whether or
not to print the image.
UNI-9 User’s Manual
5-20
Chapter 5: SETUP MODE
13.
Press the “PRINT” tab to display the “PLU Initial Data (Print)” screen.
ITEM
1st LABEL FORMAT
No. (M)
2nd LABEL
FORMAT No.
1st LABEL FORMAT
No. (A)
1st LABEL PRINT
2nd LABEL PRINT
UNI-9 User’s Manual
DESCRIPTIONS
Enter a desired format number and press this field.
Enter a desired format number and press this field.
Enter a desired format number and press this field.
Press [  ] or [  ] to select whether or not to print the first label.
1: Yes
2: No
Press [  ] or [  ] to select whether or not to print the second label.
1: Yes
2: No
5-21
Chapter 5: SETUP MODE
14
Press the “DATE” tab to display the “PLU Initial Data (Date)” screen.
.
ITEM
PACK DATE PRINT
PACK TIME PRINT
PACK TIME
DATA
SB DATE PRINT
SB TIME PRINT
SB TIME
DATA
SHELF LIFE
(days)
USE BY DATE
PRINT
UB DATE
DATA
UNI-9 User’s Manual
DESCRIPTIONS
Press [YES] or [NO] in this field to select whether or not to print the packed
date.
Press [] or [] to select a desired pack time printing method.
0: No print
1: Designated time
2: System clock time
This field is available only when “1: Designated time” is
selected in “PACK TIME PRINT”. Enter the time and press
this field.
Press [YES] or [NO] in this field to select whether or not to print the sell-by
date.
Press [] or [] button to select a desired sell-by time printing method.
0: No print
1: Designated time
2: Relative time
This field is available only when “Yes” is selected in “SB TIME
PRINT”.
Enter the number of hours and press this field.
This field is available only when “Yes” is selected in “SB DATE
PRINT”.
Enter the number of days and press this field.
Press [YES] or [NO] in this field to select whether or not to
print the use-by date.
This field is available only when “Yes” is selected in “USE BY
DATE PRINT”.
Enter the number of hours and press this field.
5-22
Chapter 5: SETUP MODE
15.
Press the “CODE” tab to display the “PLU Initial Data (Code)” screen.
DESCRIPTIONS
ITEM
ITEM CODE
Enter an item code and press this field.
REG CODE
Enter the register code and press this field.
This field is available only when “1: PLU File” is selected in “POS
POS FLAG
REFERENCE”.
Enter a POS flag number and press this field.
BARCODE
Enter a barcode number and press this field.
Press [] or [] button to select a desired reference method.
POS REFERENCE
0: Refer
1: PLU file
This field is available only when “1: PLU File” is selected in “POS
REFERENCE”.
Press this field to display the “Barcode Type” screen, and press a desired
PLU type for selection.
BARCODE TYPE
UNI-9 User’s Manual
5-23
Chapter 5: SETUP MODE
Press this field to display the “Barcode Format” screen, and press a
desired barcode format for selection.
POS FORMAT
(WGT)
TRACE ENABLE
DEPARTMENT No.
GROUP No.
UNI-9 User’s Manual
Press [YES] or [NO] in this field to select whether or not to enable a
traceability function.
Press this field to display the “Department” screen.
To set a department, press a desired field on the list, or press the
“DEPARTMENT No.” field after numerical entry.
Press this field to display the “Group” screen.
To set a group, press a desired field on the list, or press the “GROUP
No.” field after numerical entry.
5-24
Chapter 5: SETUP MODE
16.
Press the “LINK” tab to display the “PLU
Initial Data (Link)” screen.
UNI-9 User’s Manual
17.
Press the Return button to complete the
procedure.
5-25
Chapter 5: SETUP MODE
5.10 PLU UPDATE
1.
Press the “PLU UPDATE” icon on the menu
selection screen.
The “PLU Update” screen is displayed.
To turn pages, press [] or [].
Note: Display items may vary depending on the
country setting.
UNI-9 User’s Manual
5-26
Chapter 5: SETUP MODE
2.
UNI-9 User’s Manual
Enter the start and end numbers and press
these fileds respectively to specify the target
PLUs.
5-27
Chapter 5: SETUP MODE
3.
Press desired items for selection.
Note 1: To clear the selection, press the selected
field again.
Note 2: To clear all selections at one time, press the
[BATCH DELETE] button.
4.
Press the [EXEC] button to update the
selected items.
UNI-9 User’s Manual
5.
The confirmation screen is displayed.
Press [EXEC] to renew all data, or [STOP] to
go back.
5-28
Chapter 5: SETUP MODE
5.11 RECEIPT SETTING
1.
Press the “RECEIPT SETTING” icon on the
menu selection screen.
3.
The text edit screen is displayed.
Edit the text according to the procedure
described in Appendix “Text Editing”.
5.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
2.
The “Receipt Setting (Title)” screen is
displayed.
To edit the header and footer titles, press the
corresponding field.
4.
To finish the editing, press the Return button
on the screen.
6.
To edit the header and footer logo images,
press the corresponding field.
5-29
Chapter 5: SETUP MODE
7.
9.
The “Header Image” screen is displayed.
8.
Press a desired image for selection.
The selected logo image has been
registered.
UNI-9 User’s Manual
5-30
Chapter 5: SETUP MODE
5.12
1.
2.
tax registration
Press the “TAX” icon on the menu selection
screen.
The “Tax” screen is displayed.
ITEM
TAX TYPE
TAX RATE
UNI-9 User’s Manual
DESCRIPTIONS
Press a desired tax type for selection.
Exclusive tax
Inclusive tax
Tax exemption
Enter a numerical value and press the applicable field.
5-31
Chapter 6: ADJUSTMENT MODE
6
ADJUSTMENT MODE
6.1
1.
ADJUSTMENT MODE ENTRY / EXIT
Ensure that the initial screen is displayed.
Then, press the Return button on the screen
to display the “Menu” screen.
2.
The “Menu” screen is displayed.
Then, press the [ADJUST] button.
Note: The content of the initial screen may differ
depending on the settings on your machine.
The adjustment menu selection screen is displayed.
Note: To exit the Adjustment Mode, press the [SALES] button.
UNI-9 User’s Manual
6-1
Chapter 6: ADJUSTMENT MODE
6.2
DATE / TIME
1.
Press the “DATE TIME” icon on the menu
selection screen.
The “Date / Time” screen is displayed.
2.
To change the date, press the “DATE” field and enter a new date data. Then, press the [SET] key.
EXAMPLE 22 June, 2007
1
Enter
2
3.
To change the time, press the “TIME” field and enter a new time data. Then, press the [SET] key.
EXAMPLE 13:50:00
UNI-9 User’s Manual
6-2
Chapter 6: ADJUSTMENT MODE
1
Enter
2
4.
To register new date and time, press the
[SET] button.
UNI-9 User’s Manual
5.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
6-3
Chapter 6: ADJUSTMENT MODE
6.3
TOUCH SCREEN
1.
Press the “TOUCH SCREEN” icon on the
menu selection screen.
The “Touch Screen” screen is displayed.
2.
Press [+] on the button at the upper left of the
screen with a round-pointed device.
Press [+] on the button at the lower right of
the screen.
4.
Press [+] on the [SET] button to confirm
calibration and save.
UNI-9 User’s Manual
3.
6-4
Chapter 6: ADJUSTMENT MODE
6.4
DISPLAY CHECK
1.
Press the “DISPLAY CHECK” icon on the
menu selection screen.
3.
Press the [HORIZONTAL] button to change
to the horizontal display check screen.
UNI-9 User’s Manual
2.
4.
The “Display Check (Vertical)” screen is
displayed.
Press [-] or [+] to adjust the vertical
brightness for operator and customer
displays.
The “Display Check (Horizontal)” screen is
displayed.
Press [-] or [+] to adjust the horizontal
brightness for operator and customer
displays.
6-5
Chapter 6: ADJUSTMENT MODE
6.5
1.
SOUND
Press the “DISPLAY CHECK” icon on the
menu selection screen.
UNI-9 User’s Manual
2.
The “Sound” screen is displayed.
To set sound levels, press “ON” in the
“Sound” field and press [ < ] or [ > ].
6-6
Appendix: TEXT EDITING
A
TEXT EDITING
A.1
EDIT SCREENS
Upper-case mode
Used to finalize
the editing
Displays the
called number
Displays the number of
input characters
Displays the number of remaining
Press this field to select a
desired font size
Press this field to select a
desired font style
characters
Lower-case mode
UNI-9 User’s Manual
A-1
Appendix: TEXT EDITING
UNI-9 User’s Manual
A-2
Appendix: TEXT EDITING
A.2
EDIT KEYS
Used to switch between
lower-case and upper-case
character modes.
Used to specify a normal
character style.
Used to begin a new line.
Used to specify a bold character
font style.
Used to delete a line text at the
place where the cursor is placed.
Used to specify a reverse
character font style.
Used to delete a character at the
place where the cursor is placed.
Used to move the cursor to the
right.
Used to delete a character by
moving the cursor back by one
character.
Used to move the cursor to the
left.
Used to specify an underlined
character font style.
Used to move the cursor up.
Used to specify an Italic character
style.
Used to move the cursor down.
Also used to select characters for
changing the style.
Used to copy the original data to
the current data.
Used to enter a space.
Used to erase the full text currently
being called.
Used to display the following key screen.
UNI-9 User’s Manual
A-3
Appendix: TEXT EDITING
Used to display the following key screen.
UNI-9 User’s Manual
A-4
Appendix: TEXT EDITING
A.3
INPUT EXAMPLES
A.3.1
1.
TEXT EDITING
Enter desired characters using alpha-numeric keys.
Upper-case characters
2.
Lower-case characters
To begin a new line, press the [New Line] key.
Enter desired characters.
3.
To register the editing, press the Return
button.
UNI-9 User’s Manual
4.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
A-5
Appendix: TEXT EDITING
A.3.2
1.
FONT STYLE SELECTION
Press the following keys to select a desired font style.
Note: The selected font style is displayed in the “STYLE” display field.
2.
Enter desired characters using alpha-numeric keys.
UNI-9 User’s Manual
A-6
Appendix: TEXT EDITING
Press the Return key to register the editing.
UNI-9 User’s Manual
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
A-7
Appendix: TEXT EDITING
A.3.3
1.
3.
LINE DATA DELETION
Press the [Line Delete] key to delete the line
data.
2.
The line data has been deleted.
Press the Return button to register the
deletion.
The confirmation screen is displayed.
To confirm changes, press [SAVE].
To undo changes, press [CANCEL].
UNI-9 User’s Manual
A-8
Appendix: TEXT EDITING
A.3.4
1.
3.
DATA ERASE
Press the [ERASE] button to delete the full
text currently being called.
2.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
The full text has been erased.
UNI-9 User’s Manual
A-9
Appendix: TEXT EDITING
A.3.5
1.
DATA COPY
To call up a desired string of characters,
press the INPUT field at the bottom right of
the screen to display the keypad.
2.
Then, enter a numerical value and press the
[SET] key on the keypad.
Enter
2
3.
5.
Press the [COPY] key while the number is
displayed in the INPUT field.
4.
The confirmation screen is displayed.
Press [EXEC] to continue, or [STOP] to go
back.
The specified text has been copied.
UNI-9 User’s Manual
A-10
Design and specifications are subject to change without notice.
44 SANNO-CHO, SHOGOIN, SAKYO-KU
KYOTO, 606-8392 JAPAN
PHONE: 81-75-771-4141
FACSIMILE: 81-75-751-1634
URL: http://www.ishidajapan.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement