User manual | Braemar Furnace WF2000
Add to my manuals2 Pages
Braemar WF2000 is a gas wall furnace designed to provide efficient and comfortable heating for your home. Equipped with a variable heat setting knob, it allows you to select the desired temperature between "1" and "7". The fan operation can be set to AUTO for automatic adjustment or BOOST for rapid heat-up. The igniter button and pilot meter make it easy to light and monitor the heater. For optimal performance and longevity, regular maintenance is recommended, including a routine check at the start of each heating season by an authorized Braemar service agent.
advertisement
When you contact your Dealer regarding service or warranty please quote the model number and serial number as shown on the heater control panel inside the control access door.
OWNER’S MANUAL
Wall Furnace - WF2000
612195g
Warranty Service
Australia 1-300-650-644 seeleyinternational.com
It is the policy of Seeley International to introduce continual product improvement. Accordingly, specifications are subject to change without notice. Please consult with your dealer to confirm the specifications of the model selected.
seeleyinternational.com.au
AU 1102
(English) (WF2000)
2
OPERATING INSTRUCTIONS
Care Instructions
External surfaces should be cleaned with warm water and detergent with the heater turned off. Do not use abrasive cleaners as scratching of the surface will occur.
Recommended Maintenance
Periodic maintenance of your Braemar
Wall Furnace will ensure a long and satisfactory service life with the heater delivering optimum performance.
It is recommended that you contact your authorised Braemar service agent to arrange a routine maintenance check at the start of each heating season.
Service and maintenance work must only be carried out by Authorised personnel.
Fan
Auto / Boost switch
Warning
Do not place articles on or against this appliance.
Do not use or store flammable materials near this appliance.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
Do not modify this appliance.
Pilot meter
WF2000
Igniter button
Gas control knob
OPERATING INSTRUCTIONS
Introduction
For satisfactory performance of your
Braemar gas wall furnace, please read these instructions carefully. The operation of the heater is controlled by the gas control knob and fan switch located behind the access door on the front cover.
Heat Setting
- Turn gas control knob anti-clockwise to
desired heat setting between “1” and
“7”.
- The heater will automatically adjust the
gas flow to maintain the room
temperature corresponding to the
selected heat setting.
Fan Operation
The fan will start automatically in both
AUTO and BOOST positions when the unit is warm enough after the burner is turned on, and stop automatically when the unit has cooled sufficiently after the burner turns off. With AUTO selected the unit will automatically select between "low" and "normal" (and
“boost” on 40MJ models) fan speeds based on the heated air temperature - no further user adjustment is necessary.
When BOOST is selected the fan will run only on its boost speed. It is recommended that the manual fan switch be set to AUTO for normal operation, or BOOST for rapid heat-up.
To Increase Heat Setting
- Turn gas control knob anti-clockwise
towards “7”.
To Decrease Heat Setting
- Turn gas control knob clockwise
towards “1”.
To Turn Off Main Burner
- Turn gas control knob clockwise
towards “PILOT” position. It is
recommended that the pilot be left in
operation during the heating season.
To Turn Off Completely (end of heating season)
- Turn gas control knob clockwise
to the “0” position.
Gas Control
To light the heater:
- Turn the gas control knob anti-
clockwise from the “0” position to the
position.
- Depress knob fully and hold down.
- Press the igniter button located next to
the gas control knob 3-4 times.
- Observe the pilot meter to indicate
operation of the pilot.
- Wait 20 seconds then release the gas
control knob and check the pilot meter
stays on.
- Repeat the process if required.
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project