BTX-700SW preliminary manual

BTX-700SW preliminary manual
1. Safety Instruction
WARNING


Please read carefully the instruction manual, which includes
important information about the installation, usage and maintenance.
Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
 Unpack and check carefully that there is no transportation damage before using the
unit.
 The unit is for indoor use only. Use only in a dry location.
 Do install and operate by qualified operator.
 Do not allow children to operate the fixture.
 Use safety chain when fixing the unit. Handle the unit by carrying its base instead of
head only.
 The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces.
 Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.
 Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
 Maximum ambient temperature TA: 40°C. Don’t operate it when the temperature is
higher.
 Don’t connect the device to any dimmer pack.
 During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, and it will decrease gradually
within 15 minutes.
 Make sure there are no flammable materials close to the unit while operating to avoid
fire hazard.
 Examine the power wires carefully, replace them immediately if there is any damage.
 Unit’s surface temperature may reach up to 85℃. Don’t touch the housing bare-handed
during its operation, and allow about 15 minutes for cooling the unit down before
replacing bulb or maintenance as it could be very hot.
 Avoid any inflammable liquids, water or metal objects entering the unit. Once it
happens, cut off the mains power immediately.
 Do not operate in dirty or dusty environment, do clean fixtures regularly.
 Do not touch any wire during operation as there might be a hazard of electric shock.
 Avoid power wires together twist other cables.
 The minimum distance between light output and the illuminated surface must be more
than 2.5 meters.
 Disconnect mains power before fuse/lamp replacement or servicing.
 Replace fuse/lamp only with the same type.
 In the event of serious operating problem, stop using the unit immediately.
 Never turn on and off the unit time after time.
 The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
BRITEQ®
1
BTX-700SW


Do not open the unit as there are no user serviceable parts inside.
Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical assistance
center if needed.
Disconnect the mains power if the fixture is has not been used for a long time.
Do use the original packing materials before transporting it again.
Caution
 To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
 Hot lamp explosion hazard. Do not open the unit within 15 minutes after switching off.
 Do replace the bulb once it is damaged, deformed or life-expired.
 Do not look directly at the light while the bulb is on.
 Never touch bulb with bare fingers, as it is very hot after using.
 Do not start on the unit without bulb enclosure or when housing is damaged.
Product Items
 User manual
 2 x Omega clamps
2. Installation
Unpacking the fixture (for flight case pack only)
1.Stop the flight case via the brake sheet above the wheels.
2.Unlock the lock modules (1) and open the cover board.
3.Prop the cover board with lid bracket.
4.Take out the fixture.
5.Unlock the lock module (2) take out omega clamps.
Installation:
1. Bolt each clamp (1) to the Omega holder with screw and
lock nut through the hole in the holder.
2. Fasten the omega holders (2) on the bottom of the base by
inserting quick-lock fasteners (3) into the holes of the base
and tighten fully clockwise.
3. Hang the fixture to the support (4) through clamp and fasten the screws (5). Fasten the
safety cable (6) through the bottom of the base and over the support.
Fig.1
Fig.2
Attention:
 Always ensure that the structure to which you are attaching the unit is secure and is
able to support a weight of 10 times of the unit’s weight.
BRITEQ®
2
BTX-700SW



Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
Always ensure that the unit is firmly fixed to avoid vibration and slipping while
operating.
The equipment must be fixed by professionals. And it must be fixed at a place where is
out of the touch of people and has no one pass by or under it.
3. Technical Specification
Power supply
- AC 100V~240V 50/60Hz
Power Consumption
- 881W (230V)
- 919W (120V)
Fuse
- T 15 A
Lamp
- Philips MSR Gold 700/2 mini FastFit
Battery backup display
- Setting DMX address or other functions without connecting to mains power.
- Battery for LCD display charges automatically when the fixtures connects to the mains
power.
- No need to change battery.
Wireless control (for the unit with wireless receiver built-in only)
- Wirelessly controlled by W-DMX (option).
- Each W-DMX is sending out 512 channels of DMX.
- License free band of 2.45 GHz
Optical system
- High efficiency optical system, delivering extremely powerful output
- High quality diachronic lenses
- Beam angle: 15°~35°
Movement
- Pan: 540°
- Tilt: 270°
- Pan/Tilt moving speed adjustable.
- Automatic Pan/Tilt correction.
- Easy calibration and maintenance by magnetic home positioning.
- Pan/Tilt position lock for transporting protection.
Shutter/Dimmer
- Blackout, 0~100% smooth dimming, independent shutter and various strobe effect.
Color wheel
- Color wheel: 7 diachronic colors + open.
- Rainbow effect in both directions.
- Easy calibration and maintenance by magnetic home positioning.
CMY
- CMY speed adjustable.
- Optional multiple preset colors and macros available.
Gobo wheel
- Gobo size: Ø26.8mm (Ø24mm for image)
- Gobo Wheel 1: 7 rotating, index able, easily replaceable gobos + open.
- Gobo Wheel 2: 8 metallic gobos + open.
BRITEQ®
3
BTX-700SW
- Easy calibration and maintenance by magnetic home positioning.
- Module design for easy assembly and service.
Prism
- 3 facets prism with rotating effect.
Frost
- Variable, separate effect.
Focus
- Focus effect.
Iris
- Motorized, stepless.
Zoom
- Motorized linear zoom for smooth adjustment of beam size and beam sharpness.
Cool
- Fan cooled
Protocols
- DMX 512
- Date input/output: 3/5 Pin XLR socket
Weight
- 23.2kgs
Dimension
- 447× 369×597 mm
Photometric diagram
BRITEQ®
4
BTX-700SW
DMX Channels
Mode
CH
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Mode 1
22-CH
Pan
Pan Fine
Tilt
Tilt Fine
Pan /Tilt Speed
Shutter
Dimmer
Color
Cyan
Magenta
Yellow
Preset Color
Gobo 1
R-Gobo 1
Gobo 2
Prism
R-Prism
Iris
Frost
Zoom
Focus
Function
Mode 2
22-CH
Shutter
Dimmer
Cyan
Magenta
Yellow
Color
Gobo 1
R-Gobo 1
R-Gobo 1 Fine
Gobo 2
Prism
R-prism
Iris
Focus
Zoom
Pan
Pan Fine
Tilt
Tilt Fine
Pan/Tilt Speed
Frost
Function
Mode 3
25-CH
Pan
Pan Fine
Tilt
Tilt Fine
Pan /Tilt Speed
Function
Pan/Tilt Macro
Pan/Tilt Macro Speed
Color
Cyan
Magenta
Yellow
Preset Color
CMY Speed
Color Macro
Gobo 1
R-Gobo 1
R-Gobo 1 Fine
Gobo 2
Prism
R-Prism
R-Prism Fine
Frost
Iris
Zoom
Focus
Shutter
Dimmer
Dimmer Fine
4. Description
the pan lock/unlock lever (6) is in lock position. To unlock the head, press the tilt unlock
button (5) and move the pan lock/unlock lever (6) to unlock position.
Caution: The head and arm must be unlocked before operation!
4.2 Control Panel
Front view
Rear view
○,1
Monitor (Batter Back-up display):
○,2
LED
POWER
DMX
○,3
On
On
Button
MENU
UP
DOWN
ENTER
○,4
Power on
DMX input present
To enter into move backward or leave the menu
To go backward to move up in the menu
To move down in the menu
To perform the desired functions
Antenna (optional)
Receive wireless signal from a wide range
○,5
DMX input/output:
For DMX 512 operation, use 3/5-pin XLR plug cable to link the units together
○,6
Power Switch:
Turns On/Off the power
4.1 Description of the fixture
○,7
1.Arm
2.Front panel
3.head
4.Tilt lock button (Black)
5.Tilt unlock button (Gray)
6.Pan lock
7.Handle
8.Base
9.Antenna (optional)
Power Cable:
To connect to the mains supply
○,8
Fuse (T 15 A):
Protect the unit from damage of over current.
The head can be locked for transportation protection-the tilt lock button (4) is pressed and
BRITEQ®
5
BTX-700SW
BRITEQ®
6
BTX-700SW
5.2 Lamp
5. Gobo and Lamp
5.1 Inserting/Exchanging rotating gobos
MSR/ MSD Gold 700/2 miniFastFit




GOBO WHEEL 1 (replaceable)
GOBO WHEEL 2
DANGER!
Install the gobos with the device switched off only.
Unplug from mains before changing gobos!

CAUTION: Never unscrew the screws of the rotating gobo as the ball bearing will
otherwise be opened!
Please follow the steps below to insert/change rotating gobos
1. Open the cover by loosening the fastening screws on the cover.
2. Push the gobo plate (follow the direction 1) and gently pull out the plate (follow the
direction 2).
3. Take out the ring with an appropriate tool. Do not touch the surface of the glass gobo.
4. Remove the original gobo and inset a new one (glazy side towards the lamp). Insert the
ring to secure it in the gobo holder.
5. Install the gobo plate back into the gobo wheel. Make sure the gobo plate is installed
under the pressure plate.
BRITEQ®
7

BTX-700SW
Because of its high internal pressure, there might be a risk that the Discharge
lamp would explode during operation. The lamp emits intense UV radiation which
is harmful to the eyes and skin. The high luminance of the arc can cause severe
damage to the retina if you take a close look at the lamp.
To protect the lamp, always turn off the lamp first (via control panel or DMX
controller) and let the unit run at least five minutes to cool down before switching
off the mains supply. Never handle the lamp or luminaries when it is hot.
Do not touch the bulb with bare hands. If this happens, clean the lamp with
denatured alcohol and wipe it with a lint free cloth before installation.
The lamp generates UV radiation. Never operate the lamp without appropriate
shielding.
When lighting up, the lamp operates at high pressure and there is a slight risk of arc
tube rupture. The risk increases with age, temperature and improper handling of the
lamp. Do not use the lamp longer than its lifespan.
Make sure the lamp is located in the center of the reflector for the best projection.
Change Lamp
WARNING
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
1. Turn off the power.
2. Unscrew the two screws (A), open the lamp cover, turn it to
the position as the sketch shown below.
3. Hold the base of the lamp, anticlockwise turn until it is parallel
to the groove.
4. Inset a new lamp follow the groove, turn it clockwise to fix the
lamp.
5. Tighten the screws (A) to fix the lamp cover.
6. Turn the screws (B) to adjust the lamp position be sure it is located in the center of the
reflector for the best projection.
BRITEQ®
8
BTX-700SW
6. How To Set The Unit
DMX Address
6.1 Power On Display
Every time you turn on the unit, it will run built-in program to reset all motors to their home
position, the display will show as fig.4, you may hear some noises for about 20 seconds. It
will show warning sign if it goes wrong during resetting and you can press the MENU button
to view the error information. After that the unit will be ready to receive DMX signal and the
display will show as fig.5.
1
512
Mode 1(22)
DMX Channel Mode
Mode 2(22)
Mode 3(29)
DMX Functions
View DMX Value
Active
WDMX Setting
Retransmit
Reset Menory
Pan Inverse
Fig.4
Fig.5
Tilt Inverse
Explanation of fig.5:
Fixture Setting
Lamp 40°C
001
Md.1 22Ch.
Present temperature of base CPU is 40°C
Present start address
Present channel mode is mode 1 (22 channels mode)
Lamp 30°C
Present temperature of lamp is 30°C
P/T Feedback
Bl.o. P/T Moving
Bl.o. Color Change
Bl.o. Gobo Change
Warning signal blinking direct resetting error
On/Off
MENU
6.2 Main Function
Turn on the unit, press MENU button into menu mode, press UP and DOWN button until the
required function is shown on the monitor. Select the function by ENTER button. Use UP
and DOWN button to choose the submenu, press the ENTER button to store and
automatically return to the last menu. Press MENU button or let the unit idle one minute to
exit menu mode.
In the event of disconnecting with mains power, press UP button for one minute to enter
into menu mode. Press MENU button or let the unit idle one minute to exit.
State/Power On
(1)
Off Via Dmx
Lamp Setting
On if Dmx On
Off if Dmx Off
The main functions are shown below(the grayed boxes are preset settings):
Cooling Mode
Display Setting
No
Yes
No
Yes
No
Yes
No
Yes
OFF
ON
OFF
ON
No
Yes
No
Yes
No
Yes
Auto
High
0-255S
Temperature Unit
Fixture Test
No
Yes
Low Power Delay
Backlight Intensity
No
Yes
No
0-255S
Backlight Auto Off
No
Yes
Yes
Ignition Delay
Display Inverse
No
Yes
No
Yes
No
Yes
1-10
C
F
Auto Test
Manual Test
Fixture use time
Fixture Information
Lamp On time
Exit
Reset Time
Fireware Version
BRITEQ®
9
BTX-700SW
BRITEQ®
10
BTX-700SW
Active
Select Active, press ENTER button to confirm, use UP and DOWN button to select Yes
(wireless control available) or No (wireless control unavailable), press ENTER button to
store. Press MENU button back to the last menu or let the unit idle one minute to exit
menu mode.
(Set wireless control to be available, the power indicate LED will strobe)
Retransmit
Select Retransmit, press ENTER button to confirm, use UP and DOWN button to
select Yes or No, press ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
Reset Memory
Select Reset Memory, press ENTER button to confirm, use UP and DOWN button to
select Yes (refuse wireless signal) or No , press ENTER button to store. Press MENU
button back to the last menu or let the unit idle one minute to exit menu mode.
Fixture Setting
DMX Functions
Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP
and DOWN button to select DMX Address, DMX Channel Mode, View DMX Value or
WDMX Setting.
DMX Address—DMX512 address setting
Select DMX Address, press ENTER button to confirm, the present address will blink on
the display, use UP and DOWN button to adjust the address from 0 to 512, press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
DMX Channel Mode—channel mode
Select DMX Channel Mode, press ENTER button to confirm, present channel mode
will blink on the display, use UP and DOWN button to select Mode1 (22 channels
mode) or Mode 2 (22 channels mode) or Mode 3 (29 channels mode), press ENTER
button to store. Press MENU button back to the last menu or let the unit idle one minute
to exit menu mode.
View DMX Value
Select View DMX Value, press ENTER button to confirm. Channel function and its
value will show on the display, use UP and DOWN button to view other DMX value.
Press MENU button back to the last menu or let the unit idle one minute to exit menu
mode.
WDMX Setting—wireless control setting
(For the unit with wireless receiver built-in only)
Select WDMX Setting, press ENTER button to confirm. Use UP and DOWN button to
select Active, Retransmit or Reset Memory, press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one minute to exit menu mode.
BRITEQ®
11
BTX-700SW
Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and
DOWN button to select Pan Inverse, Tile Inverse, BL.O. P/T Moving, BL.O. Color
Change or BL.O. Gobo Change.
Pan Inverse
Select Pan Inverse, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select No (normal) or Yes (pan inverse), press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
Tilt Inverse
Select Tilt Inverse, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select No (normal) or Yes (tilt inverse), press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
P/T Feedback — pan/tilt Feedback
Select P/T Feedback, press ENTER button to confirm, present mode will blink on the
display, press UP/DOWN button to select No (Pan or tilt’s position will not feedback
while out of step.) or Yes (Feedback while pan/tilt out of step. ), press ENTER button to
store. Press MENU button back to the last menu or let the unit idle one minute to exit
menu mode.
BL.O. P/T Moving—Blackout while pan/tilt moving
Select BL.O. P/T Moving, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select No (normal while pan/tilt moving) or
Yes (blackout while pan/tilt moving), press ENTER button to store. Press MENU button
back to the last menu or let the unit idle one minute to exit menu mode.
BL.O. Color Change—Blackout while change color
Select BL.O. Color Change, press ENTER button to confirm, present mode will blink
BRITEQ®
12
BTX-700SW
on the display, use UP and DOWN button to select No (normal while changing color) or
Yes (blackout while change color), Press MENU button back to the last menu or let the
unit idle one minute to exit menu mode.
BL.O. Gobo Change—Blackout while change gobo
Select BL.O. Gobo Change, press ENTER button to confirm, present mode will blink
on the display, use UP and DOWN button to select No (normal while changing gobo) or
Yes (blackout while changing gobo), press ENTER button to store. Press MENU button
back to the last menu or let the unit idle one minute to exit menu mode.
Lamp Setting
Attention: The lamp will not be on unit detected temperature is lower than 45°C.
Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and
DOWN button to select On/Off, State/Power on, Off Via DMX, On if DMX on, Off if
DMX off, Cooling Mode, Ignition Delay or Low Power Delay..
On/Off—Turn on/off the lamp
Select On/Off, press ENTER button to confirm, present mode will blink on the display,
use UP and DOWN button to select On (lamp on) or Off (lamp off), press ENTER
button to store. Press MENU button back to the last menu or let the unit idle one minute
to exit menu mode.
State/Power On—Lamp state while power on
Select State/Power On, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select On (Lamp on while power on) or Off (Lamp
off while power on), press ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
Off Via DMX—Turn off the unit via DMX controller
Select Off Via DMX, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select Yes (turn off the unit via DMX controller
available) or No (turn off the unit via DMX controller impracticable), press ENTER
button to store. Press MENU button back to the last menu or let the unit idle one minute
to exit menu mode.
(When you operate the unit via DMX controller, set the value of channel “special
function” to “lamp off”, waiting for 5 seconds, then the lamp will be off if you choose
“yes” mode).
On If DMX On—Lamp turns on when DMX signal is detected
Select On If DMX On, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select Yes (Lamp turns on when DMX signal is
detected) or No (keep the present state), press ENTER button to store. Press MENU
button back to the last menu or let the unit idle one minute to exit menu mode.(If the
lamp is off via DMX signal, you can reconnect the DMX controller to make the lamp on).
BRITEQ®
13
BTX-700SW
Off If DMX Off—l Lamp turns off when DMX signal is cut off
Select Off If DMX Off, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select Yes (Lamp turns off when DMX signal is
cut off), press ENTER button to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.
Cooling Mode—Lamp turns off when DMX signal is cut off
Select Cooling Mode, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select Auto (fans speed adjust automatically)
or High (fans run in high speed), press ENTER button to store. Press MENU button
back to the last menu or let the unit idle one minute to exit menu mode.
Ignition Delay—Delay time between power on and lamp on
Select Ignition Delay, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to adjust the delay time from 0S to 255S, press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
Low Power Delay—Delay time between reduce lamp power and shutter off the unit
Select Low Power Delay, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to adjust the delay time from 0S to 255S, press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
(If you set the low power delay time to 3S, the lamp will run in half power 3 seconds
after the unit shutter off)
Display Setting
Enter menu mode, select Display Setting, press ENTER button to confirm, use UP
and DOWN button to select Display Inverse, Backlight Auto Off, Backlight Intensity
or Temperature unit.
Display Inverse
Select Display Inverse, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select No (normal display) or Yes (inverse
display), press ENTER button to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.
Backlight Auto Off
Select Backlight Auto Off, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select No (display always on) or Yes (display
goes off one minute after exiting menu mode), press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one minute to exit menu mode.
Backlight Intensity
Select Backlight Intensity, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to adjust backlight intensity from 1 (dark) to 10
(bright), press ENTER button to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.
BRITEQ®
14
BTX-700SW
Temperature Unit
Select Temperature Unit, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select ℃ or ℉, press ENTER button to store.
Press MENU button back to the last menu or let the unit idle one minute to exit menu
mode.
Fixture Test
Enter menu mode, select Fixture Test, press ENTER button to confirm, use UP and
DOWN button to select Auto Test or Manual Test
Auto Test
Select Auto Test, press ENTER button to confirm, the unit will run built-in programs to
automatically test pan, tilt, color, CMY, gobo, gobo rotation, shutter, dimmer, prism,
prism rotation, frost, zoom, iris, focus, flatb and lamp on/off. Press MENU button back
to the last menu or exit menu mode after auto test.
Manual Test
Select Manual Test, press ENTER button to confirm, the present channel will show on
the display, use Up and DOWN button to select channel, press ENTER button to
confirm, then use UP and DOWN button to adjust the value, press ENTER button to
store, the fixture will run as the channel value indicates. Press MENU button back to the
last menu or exit menu mode idling one minute.
(All channels value will become 0 after exiting Manual Test menu)
Fixture Information
Enter menu mode, select Fixture Information, press ENTER button to confirm, use
UP and DOWN button to select Fixture Use Time, Lamp On Time or Firmware
Version.
Fixture Use Time
Select Fixture Use Time, press ENTER button to confirm, fixture use time will show on
the display, press MENU button back to exit.
Lamp On Time
Select Lamp On Time, press ENTER button to confirm, lamp on time will show on the
display, press ENTER button to confirm, use UP and DOWN button to select Exit or
Reset Time, press ENTER button to confirm. Press MENU button back to the last
menu or exit menu mode let the unit idle one minute.
Firmware Version
Select Firmware Version, press ENTER button to confirm, firmware version will show
on the display, press MENU button back to exit.
Reset Functions
Enter menu mode, select Reset Function, press ENTER button to confirm, use UP
and DOWN button to select Pan/Tilt, Color/CMY, Gobo, Shutter/Dimmer,
Focus/Zoom/Prism/Frost , Iris/Flatb or All.
BRITEQ®
15
BTX-700SW
Pan/Tilt—Reset Pan/Tilt
Select Pan/Tilt, press ENTER button to confirm, use UP and DOWN button to select
Yes (the unit will run built-in program to reset pan and tilt to their home positions) or No,
press ENTER button to store. Press MENU button to exit.
Color/CMY—Reset Color/CMY
Select Color/CMY, press ENTER button to confirm, use UP and DOWN button to
select Yes (the unit will run built-in program to reset color and CMY to their home
positions) or No, press ENTER button to store. Press MENU button to exit.
GOBO—Reset GOBO
Select GOBO, press ENTER button to confirm, use UP and DOWN button to select Yes
(the unit will run built-in program to reset GOBO wheel to their home positions) or No,
press ENTER button to store. Press MENU button to exit.
Shutter/Dimmer—Reset Shutter/Dimmer
Select Shutter/Dimmer, press ENTER button to confirm, use UP and DOWN button to
select Yes (the unit will run built-in program to reset shutter and dimmer to their home
positions) or No, press ENTER button to store. Press MENU button to exit.
Focus/Zoom/Prism/Frost—Reset Focus/Zoom/Prism/Frost
Select Focus/Zoom/Prism/Frost, press ENTER button to confirm, use UP and DOWN
button to select Yes (the unit will run built-in program to reset focus, zoom, prism and
frost to their home positions) or No, press ENTER button to store. Press MENU button
to exit.
Iris/Flatb—Reset Iris/Flatb
Select Iris/Flatb, press ENTER button to confirm, use UP and DOWN button to select
Yes (the unit will run built-in program to reset iris and flatb to their home positions) or
No, press ENTER button to store. Press MENU button to exit.
All—Reset All
Select All, press ENTER button to confirm, use UP and DOWN button to select Yes
(the unit will run built-in program to reset all motors to their home positions) or No,
press ENTER button to store. Press MENU button to exit.
Special Functions
Enter menu mode, select Special Functions, press ENTER button to confirm, use UP
and DOWN button to select Fixture Maintenance or Factory Setting.
Fixture Maintenance
Select Fixture Maintenance, press ENTER button to confirm, use UP and DOWN
button to select Interval or Remain Time.
Interval
Select Interval, press ENTER button to confirm, the interval time will show on
BRITEQ®
16
BTX-700SW
the display. Press MENU button to exit.
Remain Time
Select Remain Time, press ENTER button to confirm, the remaining time will
show on the display, press ENTER button to confirm, use UP and DOWN button
to select Exit or Reset time, press MENU button to exit.
Factory Setting
Select Factory Setting, press ENTER button to confirm, the fixture will reset to factory
settings and exit menu mode.
6.3. Home Position Adjustment
Press MENU button into menu mode, then press ENTER button for about 3 seconds into
offset mode to adjust the home position. Select the function by ENTER button. Use UP and
DOWN button to choose the submenu, press the ENTER button to store and automatically
return to the last menu. Press MENU button to exit.
Shutter—Shutter home position adjust
Enter offset mode, Select Shutter, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Dimmer—Dimmer home position adjust
Enter offset mode, Select Dimmer, press ENTER button to confirm, the present position
will blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Color—Color home position adjust
Enter offset mode, Select Color, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from -128 to 127, press
ENTER button to store. Press MENU button to exit.
Cyan—Cyan home position adjust
Enter offset mode, Select Cyan, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Magenta—Magenta home position adjust
Enter offset mode, Select Magenta, press ENTER button to confirm, the present position
will blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Yellow—Yellow home position adjust
Enter offset mode, Select Yellow, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Gobo 1—Gobo 1 home position adjust
Enter offset mode, Select Gobo 1, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from -128 to 127, press
ENTER button to store. Press MENU button to exit.
R-Gobo 1—Gobo 1 rotation home position adjust
Enter offset mode, Select R-Gobo 1, press ENTER button to confirm, the present position
will blink on the display, use UP and DOWN button to offset the value from -128 to 127,
press ENTER button to store. Press MENU button to exit.
Gobo 2—Gobo 2 home position adjust
Enter offset mode, Select Gobo 2, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from -128 to 127, press
ENTER button to store. Press MENU button to exit.
Pan—pan home position adjust
Enter offset mode, Select Pan, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from -128 to 127, press
ENTER button to store. Press MENU button to exit.
Iris—Iris home position adjust
Enter offset mode, Select Iris, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Tilt—Tilt home position adjust
Enter offset mode, Select Tilt, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from -128 to 127, press
ENTER button to store. Press MENU button to exit.
Prism—Prism home position adjust
Enter offset mode, Select Prism, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
BRITEQ®
BRITEQ®
17
BTX-700SW
18
BTX-700SW
R-Prism—Prism rotation home position adjust
Enter offset mode, Select R-Prism, press ENTER button to confirm, the present position
will blink on the display, use UP and DOWN button to offset the value from -128 to 127,
press ENTER button to store. Press MENU button to exit.
7. Control By Universal DMX Controller
7.1 Connection
Frost—Frost home position adjust
Enter offset mode, Select Frost, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Flatb—Flatb home position adjust
Enter offset mode, Select Flatb, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Focus—Focus home position adjust
Enter offset mode, Select Focus, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Zoom—Zoom home position adjust
Enter offset mode, Select Zoom, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
6.4. Error Information
Lamp Startup Fail
It appears when there is no lamp or some wires are damaged.
Temperature Sense Error
It appears when temperature check board is damaged.
Lamp Too Hot Power Off
ATTENTION
Termination reduces signal errors and to avoid signal transmission
It appears when temperature is detected higher than 110℃. Check if the unit is properly
ventilated, or fans or temperature check board may is damaged.
Lamp Too Hot Low Power
problems and interference. It is always advisable to connect a DMX terminal
(Resistance 120 ohm 1/4W between pin2 (DMX-) and pin3 (DMX+) of the last
It appears when detected temperature is over 105℃. the unit will run on a low power level.
Maintenance Fixture
It appears when the maintenance remaining time becomes 0S, please enter menu mode
and reset the time.
Lamp On Over 700 Hour
It appears when the lamp has been on over 700 hours, please turn off the lamp.
Memory Initial Fail
It appears when the memory IC is damaged.
CPU-B Error, CPU-C Error, CPU-D Error
They appear when board P.C or some wires are damaged.
Pan Reset Error, Pan Encode Error, Tilt Reset Error, Tilt Encode Error, Shutter Reset
Fail, Dimmer Reset Fail, Color Reset Fail, Cyan Reset Fail, Magenta Reset Fail, Yellow
Reset Fail, Gobo1 Reset Fail, R-Gobo1 Reset Fail, Gobo2 Reset Fail, Iris Reset Fail,
Effect Reset Fail, R-Effect Reset Fail, Frost Reset Fail, Flatb Reset Fail, Focus Reset
Fail, Zoom Reset Fail
They may appear when turn on or reset the unit, for some parts such as board P.C are
damaged. Please contact the qualified maintenance.
1.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in
the DMX-output of the last unit.
2.Connect the unit together in a “daisy chain” by XLR plug cable from the output of the unit
to the input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX
512 is a very high-speed signal. Inadequate or damaged cables, soldered joints or
corroded connectors can easily distort the signal and shut down the system.
3.The DMX output and input connectors are pass-through to maintain the DMX circuit,
when one of the units’ power is disconnected.
4.Each lighting unit needs to have a DMX address to receive the data by the controller. The
address number is between 0-511 (usually 0 & 1 are equal to 1).
5.The end of the DMX 512 system should be terminated to reduce signal errors.
6.3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin4, Pin5 not
used.
BRITEQ®
BRITEQ®
19
BTX-700SW
20
BTX-700SW
7.2 Channel Mode Setting
Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and
DOWN button to select DMX Channel Mode, press ENTER button to confirm, present
channel mode will blink on the display, use UP and DOWN button to select Mode1 (22
channels mode) or Mode 2 (22 channels mode) or Mode 3 (29 channels mode), press
ENTER button to store. Press MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
7.4 DMX 512 Configuration
Please refer to below configurations to control the fixtures
Attention:
1. The unit will maintain the last condition until reset if you cut-off the DMX signal)
2. For the channel Function, keep the value for about 5 seconds, then the corresponding
function will take into effect.
22 Channels mode 1:
7.3 Address Setting
22Channels(Mode 1)
If you use a universal DMX controller to control the units, you have to set DMX address
from 1 to 512 so that the units can receive DMX signal.
Press MENU button to enter menu mode, select DMX Functions, press ENTER button to
confirm, use UP and DOWN button to select DMX Address, press ENTER button to
confirm, the present address will blink on the display, use UP and DOWN button to adjust
the address from 0 to 512, press ENTER button to store. Press MENU button back to the
last menu or let the unit idle one minute to exit menu mode.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
Channel mode
Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
22 channels
1
23
45
67
29 channels
1
30
59
81
Ch1
Ch2
Pan
255
Ch3
Pan Fine
540
255
Tilt
255
Ch4
Ch5
Ch6
Tilt Fine
Pan/Tilt
Speed
Shutter
255
270
255
Slow
248-255
Open
240-247 Random
Strobe
Open
204-239 Slow
Slow close
Slow Close
168-203 Fast Open
Open
132-167 Slow
Fast Close
16-131
8-15
0
0
0
Ch7
Dimmer
255
100%
0
0
0
0
Fast
Open
0-7 Blackout
Ch8
Ch9
Ch10
Ch11
Color
Cyan
Magenta
Yellow
255 Rotation Fast
255
100%
255
100%
255
100%
194 Rotation Slow
190-193 Stop
189 Rotation Slow
128 Rotation Fast
064-127 Color Mix
056-063 Blue
048-055 Green
040-047 Pink
032-039 5600K
024-031 3200K
0
BRITEQ®
21
BTX-700SW
BRITEQ®
0%
008-015 Red
001-007 White
0
0%
22
0
0%
0
0%
BTX-700SW
22 Channels mode 2:
22Channels(Mode 1)
Ch12
Ch13
Preset Color
Ch14
Gobo 1
22Channels(Mode 2)
Ch15
R-Gobo 1
Gobo2
Ch16
Ch1
Ch2
Ch3
Ch4
Ch5
Ch6
Prism
Shutter
Dimmer
Cyan
Magenta
Yellow
Color
234-255 Color11
248-255
213-233 Color10
128-255
192-212 Color9
171-191 Color8
149-170 Color7
128-148 Color6
8-127
107-127 Color5
086-106 Color4
Open
255
100% 255
100% 255
100% 255
100%
Random
Strobe
Slow
204-239 Slow Open
close
Slow Close
168-203 Fast Open
240-247
194 Rotation Slow
190-193 Stop
189 Rotation Slow
Open
132-167 Slow
Fast Close
128 Rotation Fast
064-127 Color Mix
056-063 Blue
048-055 Green
040-047 Pink
032-039 5600K
024-031 3200K
16-131
064-085 Color3
0-7
No Function
043-063 Color2
022-042 Color1
8-15
Open
0-7 Blackout
000-021 White
Ch17
Ch18
Ch19
Ch20
Ch21
Ch22
R-Prism
Iris
Frost
Zoom
Focus
Function
255 Rotation Fast
255
0%
255
0%
Ch7
Gobo 1
255
255 Rotation Fast
0
0%
0
0%
0
0%
0
0%
008-015 Red
001-007 White
Ch8
Ch9
Ch10
Ch11
R-Gobo 1
R-Gobo 1
Fine
Gobo2
Prism
255
128-255
194 Rotation Slow
190-193 Stop
8-255
Frost
189 Rotation Slow
8-127
128 Rotation Fast
0-127 Index
0
BRITEQ®
100%
0-7
No Function
0-7 Normal
0
23
100%
0
0
BTX-700SW
BRITEQ®
24
BTX-700SW
29 Channels mode:
22Channels(Mode 2)
Ch12
Ch13
Ch14
Ch15
Ch16
R-Prism
Iris
Focus
Zoom
Pan
255
0%
255
255
0%
255
29Channels(Mode 3)
Ch1
540
Pan
Ch2
Ch3
Pan Fine
Tilt
Ch4
Ch5
Ch6
Tilt Fine
Pan/Tilt
Speed
Function
255 Rotation Fast
255
540
255
255
0
0
270
255
255
0
0
Slow
194 Rotation Slow
190-193 Stop
189 Rotation Slow
128 Rotation Fast
0-127 Index
0
Ch17
Ch18
Pan Fine
255
Tilt
255
270
100%
0
0
100%
0
Ch19
Ch20
Ch21
Ch22
Tilt Fine
Pan/Tilt
Speed
Frost
Function
255
255
0
BRITEQ®
0
0
0
0
25
0
0
Fast
Slow
8-255
0
0
Fast
Frost
Ch7
Ch8
Ch9
Ch10
Ch11
Ch12
Pan/Tilt
Macro
P/ T Macro
Speed
Color
Cyan
Magenta
Yellow
248-255Macro31
240-247Macro30
232-239Macro29
224-231Macro28
216-223Macro27
208-215Macro26
200-207Macro25
192-199Macro24
184-191Macro23
176-183Macro22
168-175Macro21
160-167Macro20
152-159Macro19
144-151Macro18
136-143Macro17
128-135Macro16
120-127Macro15
112-119Macro14
104-111Macro13
096-103Macro12
088-095Macro11
080-087Macro10
072-079Macro9
064-071Macro8
056-063Macro7
048-055Macro6
040-047Macro 5
032-039Macro4
024-031Macro3
016-023Macro2
008-015 Macro1
000-007 Stop
0-7 Normal
BTX-700SW
BRITEQ®
255
Slow
255 Rotation Fast
255
100% 255
100% 255
100%
194 Rotation Slow
190-193 Stop
189 Rotation Slow
128 Rotation Fast
064-127 Color Mix
056-063 Blue
048-055 Green
040-047 Pink
032-039 5600K
024-031 3200K
0
Fast
008-015 Red
001-007 White
26
0
0%
0
0%
0
0%
BTX-700SW
29Channels(Mode 3)
Ch13
Ch14
Preset Color
CMY
Speed
234-255 Color11
255
Ch15
Ch16
Color Macro
Slow
Gobo 1
214-234Macro11
192-212 Color9
194-213Macro10
171-191 Color8
173-193 Macro9
194 Rotation Slow
190-193 Stop
111-131 Macro6
189 Rotation Slow
091-110 Macro 5
086-106 Color4
070-090 Macro4
064-085 Color3
050-069 Macro3
043-063 Color2
029-049 Macro2
022-042 Color1
008-028 Macro1
000-021 White
255 Rotation Fast
132-152 Macro7
107-127 Color5
R-Gobo 1
255
153-172 Macro8
128-148 Color6
Ch18
R-Gobo 1
Fine
235-255Macro12
213-233 Color10
149-170 Color7
Ch17
0
Fast
128 Rotation Fast
0-127 Index
0
000-007 Open
8. Update Software
Ch19
Ch20
Ch21
Ch22
Ch23
Gobo2
Prism
R-Prism
R-Prism
Fine
Frost
255 Rotation Fast
194 Rotation Slow
8-127
0-7
No Function
8-255
Frost
189 Rotation Slow
128 Rotation Fast
0-127 Index
0
9. Troubleshooting
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connect power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED to see if it can be light up or not.
255
128-255
Download update file (if available) from www.briteq-lighting.com , follow the user manual
of our firmware updater (not included, order code: 4319) to update the fixture.
0-7 Normal
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if they are linked
properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
4. Try to use another DMX controller.
5. Check to see if the DMX cables run near or run alongside high voltage cables that may
cause damage or interference to DMX interface circuit.
C. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
BRITEQ®
27
BTX-700SW
BRITEQ®
28
BTX-700SW
D. The lamp is cutting out intermittently
1. The lamp is not working well. Check the mains voltage either too high or too low.
2. Internal temperature may be too high. Check if replacement of fan is needed on the
head.
E. If The pan belt is broken
1. Turn off the mains power.
2. Loosen the screws (A),open the cover (B).
3. Loosen the screws (C).
4. Unplug all the connect wires over the belt.
5. Change a new belt (D), put the belt around the axis gear and
motor gear.
6. Plug all the connect wires back upon the belt.
7. Tighten all the screws.
F. If The tilt belt is broken
1. Turn off the mains power.
2. Loosen all the screws (A) and open the right arm
cover (B).
3. Loosen the screws (C) that fix the bridge.
4. Change a new belt (D). Please adjust the tension of
the belt properly. Note: do not fix the belt too tight as
it is can easily rupture.
5. Reverse the procedures from step 3 to 2.
10. Maintenance and Cleaning
Maintenance:
Ignitor
Ballast
Filter
A. As the pictures shown above, please replace the cable or cable joints immediately once
they’ve turned yellow.
B. Do maintain the fixtures every two months and make sure that all the screws and
terminals have been locked firmly to make sure the normal performance of the fixtures.
Negligence of maintenance would cause malfunction of the fixture.
Cleaning:
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
 Clean with soft cloth and use normal glass to clean fluid.
 Always dry the parts carefully.
 Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
BRITEQ®
29
BTX-700SW
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement