User Manual PDF
Foreword
1
We congratulate you on your choice of the legendary Bullet motorcycle and welcome you to the exciting world
of motorcycling on a Royal Enfield.This manual will help you to operate your Classic 500cc motorcycle, the right way
and guide you to maintain your motorcycle meticulously. We have also provided tips on safe riding and on minor
adjustments for the care of your motorcycle. Please avail the four free services at the nearest Authorised Service
Point, at the appropriate time to maintain your Bullet motorcycle in top riding condition. Log on to the exciting world
of Royal Enfield website: www.royalenfield.com to get to know more about the company, its products and exciting
news from time to time. We request you to carefully read the terms and conditions of warranty and other useful
information given in this manual before starting to use your Bullet Motorcycle.
Service Headquarters
Royal Enfield, A Unit of Eicher Motors Limited,
Tiruvottiyur High Road, Tiruvottiyur, Chennai - 600 019.
Phone : 044 - 4223 0400, Fax : 044 - 4201 1719
E-mail : [email protected]
Website : www.royalenfield.com
Notice
2
All information in this manual is based on the latest product information available at the time of publication.
Due to continues improvements or other changes, there may be discrepancies between information in this manual
and your vehicle. Royal Enfield reserves the right to make production changes at any time without prior notice
and without incurring any obligation to make same or similar changes to vehicles previously built or sold.
All images shown are for reference to explain and need not to be exactly the same on the model you own. Technical
specification are subject to change without prior notice.
“© Copyright 2014 Royal Enfield (A unit of Eicher Motors Ltd.). All Rights Reserved. No part of this manual shall be
copied, distributed or otherwise dealt without the express permission in writing of Royal Enfield.
Applicable for Classic Desert Storm Model
Disclaimer
Care needs to be taken as instructed below in order to
ensure a longer life for the paint.
Part No. 591822 / B / Qty. 800 / Apr. ‘14
1.
Do not polish your motorcycle as it increases gloss.
2.
Wash only with plain water.
3.
Scratches or marks cannot be removed.
No warranty for DESERT STORM Colour
Contents
3
PERSONAL & VEHICLE INFORMATION ...
FREE SERVICE RECORD ........................
6
7
Left Side View ....................................
Top View ............................................
23
24
TECHNICAL SPECIFICATIONS ................
Engine ................................................
Ignition System ...................................
8
8
9
OPERATION OF CONTROLS...................
Ignition Switch ....................................
Steering Lock ......................................
25
25
25
Transmission ......................................
Electricals ...........................................
9
10
Fuel tank cap .....................................
Side Box ............................................
26
26
Chassis ..............................................
Dimensions .........................................
Weights ..............................................
11
12
12
Battery Carrier ...................................
Utility Box ..........................................
Head lamp switch ...............................
27
27
28
SAFETY DEFINITIONS ............................
SAFE DRIVING TIPS/GUIDELINES ...........
13
14
Head lamp Day flash ..........................
Dip Switch .........................................
28
28
SAFE & HAPPY RIDING ...........................
RULES OF THE ROAD .............................
VEHICLE IDENTIFICATION ......................
18
19
21
Engine Start Switch ............................
Engine Stop Switch ............................
Turn Signal Switch .............................
29
29
29
Chassis Number..................................
Engine Number ...................................
KEY PARTS LOCATION ...........................
21
21
22
Horn ..................................................
Manual Bi Starter (choke) ...................
PRE OPERATIONAL CHECKS .................
30
30
31
Right Side View ..................................
22
RUNNING IN PERIOD ..............................
32
Contents
4
ELECTRONIC FUEL INJECTION & MIL .....
33
EFI ....................................................
33
The Advantages of EFI .......................
Malfunction Indicator Lamp (MIL) .........
33
33
ROLL OVER SENSOR .............................
34
STARTING .............................................
35
GEAR SHIFTING .....................................
38
PARKING ...............................................
Center Stand ......................................
39
39
Side Stand .........................................
39
TOOLS & FIRST AID KIT ..........................
40
Brake fluid .........................................
Inspection of tyres and wheels .............
Tyre pressure .....................................
49
49
50
Front Wheel removal ..........................
Front Wheel assembly .........................
Rear wheel removal ...........................
50
51
52
Rear wheel assembly...........................
Adjustments-Clutch .............................
53
54
Drive Chain free play ..........................
Checking Rear Brake Pedal Height.......
Rear Brake free play adjustment ..........
54
55
56
RECOMMENDED LUBRICANTS ...............
41
PERIODICAL MAINTENANCE ..................
MINOR MAINTENANCE TIPS ..................
42
46
Chain lock fitment ...............................
Adjustment of gas shockabsorber ........
Removal of Battery on Vehicle ............
56
57
58
Control Cables, Hand lever, Pivots,
Center / Side Stand Pivots ..................
46
Battery Maintenance ...........................
Assembly of Battery on Vehicle ...........
58
59
CHANGING ELECTRICAL COMPONENTS ....
Head Lamp Bulb Replacement............
Assembling the Head Lamp .................
60
60
61
Oil Level Inspection ............................
46
Engine oil change ...............................
Spark Plug .........................................
47
48
Contents
5
Tail Lamp bulb Replacement................
62
White / Blue smoke ............................
74
Trafficator bulb Replacement ..............
Fus e ..................................................
Blade fuse usage list...........................
62
63
63
Engine overheating ............................
Excessive fuel consumption ................
Brakes Poor ........................................
74
74
75
AIR FILTER PAPER ELEMENT....................
PILLION(REAR)SEAT REMOVAL & REFITTING
64
65
Vehicle wobbles .................................
Electricals ..........................................
75
75
Pillion (Rear) seat removal..................
Pillion (Rear) seat refitting...................
WASHING PROCEDURE .........................
65
66
67
Electronic Fuel Injection (EFI) ............
WARRANTY ............................................
EMISSION WARRANTY ...........................
76
77
79
Precautions .......................................
After washing .....................................
STORAGE PRECAUTION........................
67
67
68
ALL INDIA ROAD SIGNS .........................
FREE SERVICE COUPONS .....................
PAID SERVICE / MAINTENANCE RECORD..
83
84
93
Preparing the motorcycle for re-use......
LONG TRIP PRECAUTIONS....................
69
70
LOG BOOK .............................................
NOTES ...................................................
101
103
COMPLETE WIRING DIAGRAM...............
TROUBLE SHOOTING ............................
Engine fails to start ............................
71
72
72
ANNEXURES
Engine misfiring .................................
Poor pickup .......................................
73
73
Vehicle Installation Form
Pre-Delivery Inspection Report
Bike Installation Confirmation By Customer
Form 22
Personal & Vehicle Information
6
Name
Door No./St.
Locality
City
Contact Nos.
State
Res:
Off:
Pin
Mobile:
Email:
Engine No.
Battery No.
Frame No.
Battery make
Reg. No.
Licence No.
Date of Sale
Valid till dt.
Model
Key No.
Tyre make
Colour
Sold by
Dealer Code
Vehicle Installation Form (VIF) No.
Free Service Record
7
It is our endeavour to provide excellent service to your Classic 500 at all times. Towards this we provide 4 free services
at specific Intervals.
Please avail these services at the specified time, in any of the Royal Enfield Authorised Dealer / Service Point nearest
to you and as a token of satisfactory services, kindly return the free service coupon duly filled in and signed, to the
service outlet.
Availing the free services in the specified time is a prerequisite for warranty consideration. The cost of fuel, oil, grease
etc. used for all free services are chargeable to the customer.
1st Service
2nd Service
3rd Service
4th Service
Dealer / ASP
Rubber Stamp
Dealer / ASP
Rubber Stamp
Dealer / ASP
Rubber Stamp
Dealer / ASP
Rubber Stamp
Date of Service
Kms Covered
Servicing ASP /
Dealer’s Name
Address
NOTE : Please ensure that the free service details are recorded in this sheet immediately after the service is carried out.
Technical Specification
ENGINE
Engine ......................................................
4 Stroke, air cooled, single cylinder, OHV, SI & FI Engine
Capacity ...................................................
499 cc (Displacement)
Bore .........................................................
84 mm
Stroke .......................................................
90 mm
Compression ratio ....................................
8.5 : 1
Max. Power @ RPM ................................
27.2 BHP @ 5250 rpm
Max. Torque @ RPM ...............................
41.3 Nm @ 4000 rpm
Air Filter Element .....................................
Corrugated Paper Element
Engine Oil Capacity .................................
2.75 Litres.
Lubrication ...............................................
Forced Lubrication, Wet Sump
Engine Oil Grade .....................................
Royal Enfield 15W50 API SL Grade Engine Oil (JASO MA)
Cooling system ........................................
Natural Air Flow
Fuel Supply ..............................................
Electronic Fuel Injection Programmed (PGM-EFI)
8
Technical Specification
9
IGNITION SYSTEM
Ignition system ........................................
Electronic Ignition (ECU / Variable)
Spark plug Electrode gap .......................
0.70 to 0.80 mm
Spark plug ...............................................
WQR8DP (Bosch Super) M14 & UR6DC (Bosch Super) M10
TRANSMISSION
Clutch .......................................................
Wet Multiplate (7 Plates)
Primary drive ...........................................
Duplex Chain
Primary Drive Ratio .................................
2.15 : 1
Gear box ..................................................
Constant Mesh 5 Speed
Gear shift pattern ....................................
1-N-2-3-4-5
Gear Ratios .............................................
1st-3.06:1
Secondary Drive (F.D. Sprocket) ...........
18 Teeth
Final ratio .................................................
2. 11 : 1
Drive Chain links .....................................
102 links
2nd-2.01:1
3rd-1.52:1
4th-1.21:1
5th-1:1
Technical Specification
10
ELECTRICALS
Generation ...............................................
Alternator
System .....................................................
12V DC
Battery .....................................................
12V - 14 AH MF
Head lamp ...............................................
12V, 60/55 W, Halogen
Position lamp ...........................................
12V, 4W
WARNING
Using bulbs / other electrical gadgets
other than specified rating may lead to over
loading / erratic behaviour / premature
failure of electrical system.
Modifications on the bike which are not
approved by Royal Enfield may not only
disqualify for warranty, but also affects
performance of the bike.
Brake / Tail lamp .....................................
12V, 21/5 W
Turn signal ...............................................
12V, 10W - 4 nos.
Pilot lamp .................................................
12V, 2 W - 2 nos. & 12V, 4 W - 1 no.
Speedometer lamp ..................................
12V, 3.4 W - 1 no.
Turn signal / High beam indicator ..........
12V, 2 W - 2 nos.
Neutral Indicator ......................................
12V, 2 W - 1 no.
Horn (Dual) ..............................................
12V, 2.5 Amp (Max.) X2
Starter Motor ...........................................
12V, 0.9 KW
Technical Specification
11
CHASSIS
Frame ......................................................
Tubular Frame
Tyre size ..................................................
Front: 90 / 90 - 19” - 52 P
Tyre pressure ..........................................
Front- Solo: 1.41 Kg/cm2 (20 PSI) Pillion: 1.55 Kg/cm2 (22 PSI)
..........................................................
Rear- Solo: 2.11 Kg/cm2 (30 PSI) Pillion: 2.25 Kg/cm2 (32 PSI)
Fuel tank capacity ...................................
13.5 Litres***
Low fuel warning .....................................
2.5 Litres (approx)
Rear: 120 / 80 - 18” - 62 P
***Fuel tank is not a measuring instrument.
The capacity of tank may vary slightly from
specified value.
Dead stock of petrol (unusable fuel) ......
0.75 Litres (approx)
Suspension ..............................................
Front: Telescopic (Dia 35mm), Hydraulic Damping Stroke 130mm
..........................................................
Rear: Swing arm with gas filled shock absorbers Stroke 80 mm
Front fork oil capacity .............................
195 ml per leg
Front fork oil ............................................
1F Endurance (or Royal Enfield) fork oil
Brakes ......................................................
Front : Hydraulic 280 mm Ventilated Disc
..........................................................
Rear : Foot Operated 153mm Single Lead Internal expanding
Brake oil capacity ....................................
60 ml
Brake oil grade ........................................
DOT 3 or DOT 4
Technical Specification
DIMENSIONS
Length ......................................................
2170 mm
Width ........................................................
800 mm
Height ......................................................
1070 mm
Wheel base ..............................................
1370 mm
Saddle height ..........................................
800 mm
Ground clearance ....................................
135 mm
12
NOTE: BS III
This vehicle meets Emission Norms Bharat (Trem) Stage - III
WEIGHTS
Kerb Weight (with 90% Fuel) ..................
190 Kg
Max pay load ...........................................
175 Kg
NOTE :
1. Values / Dimensions given above are for your guidelines only.
2. In view of continuous improvements being done on our products, the specifications are subject to change without notice.
Safety Definitions
13
The information given under the titles : Warning, Caution and Note are for your safety and for the care and safety to
your motorcycle and others. Please read these carefully and if disregarded may result in injury to yourself or others and
damages to the motorcycle.
Warning
Indicates a potentially hazardous situation. Disregarding this message may result in injury to rider or other persons.
CAUTION :
This message if disregarded may result in damage to the vehicle.
NOTE :
Indicates important and useful messages for clear understanding.
Safe Riding Tips / Guidelines
Before operating your new motorcycle, it is your
responsibility to carefully read and follow the
operating and maintenance instructions detailed
in this m anual for y our ow n saf ety, y our
motorcycle and that of others.
Know and respect the rules of the road. Be a
safe rider for your own safety and for other road
users.
Before starting the motorcycle, check for proper
operation of brakes, clutch, gear shifter, handle
bar controls, tyre pressures, fuel and oil levels.
Use only genuine Royal Enfield spare parts and
approved accessories. Use of other manufacturer’s performance parts may affect the
performance of your motorcycle and render the
motorcycle void of warranty. See your Royal
Enfield dealer for details.
Whenever refuelling your motorcycle, please
exercise utmost caution and carefully observe
the following rules :
14
DO NOT smoke and please ensure that
there are no open flames or sparks near the
motorcycle, when refuelling OR servicing the
fuel system.
Switch OFF mobile phones and other hand
held electronic devices.
Open the fuel filler cap slowly.
Refuel in a well ventilated area with the
engine turned off.
DO NOT fill the tank to its brim. Please fill
fuel only till the bottom of the filler neck
insert, so as to leave air space in the fuel
tank to allow for fuel expansion.
Warning
Royal Enfield cautions you against the use of certain
nonstandard parts such as aftermarket and custom
made extended front forks or suspensions, which may
adversely affect performance and handling. Removing
or al tering or iginal par ts may ad v ersely a ffect
performance and could result in an accident.
Safe Riding Tips / Guidelines
A new motorcycle must be operated according
to th e speci al running -in -pr oce dure . S ee
running-in-procedure mentioned in Page No. 32.
Operate motorcycle only at moderate speeds
and out o f tra ffic u ntil y ou ha ve bec ome
thoroughly familiar with its operation and
handling characteristics under all conditions.
DO NOT exceed the legal speed limit or drive
too fast for existing conditions. Always reduce
speed when poor driving conditions exist. High
speed increases the influence of any other
condition affecting stability and increases the
possibility of loss of control.
NOTE :
If you are an inexperienced rider we recommend that
you obtain formal training on correct motorcycle riding
techniques and become thoroughly familiar with the
operation of your particular motorcycle. New riders
should gain experience under various conditions while
driving at moderate speeds.
15
Pay strict attention to road surfaces and wind
conditions. Any two wheeled vehicle may be subject
to the following upsetting forces :
Wind blasts from passing trucks.
Rough uneven road surfaces.
Slippery road surfaces.
These forces may affect the handling characteristics
of your motorcycle. If this happens, reduce speed
and guide the motorcycle with a relaxed grip to a
controlled condition. Do not brake abruptly or force
the handlebar.
Oper ate y our m otorc ycl e def en siv el y.
Remember, a motorcycle does not afford the
same pr otect ion as an a ut omo bil e i n an
accident. One of the most common accident
situations occurs when the driver of the other
vehicle fails to see or recognize a motorcycle
and turns into the oncoming motorcyclist.
Safe Riding Tips / Guidelines
Wear an approved helmet, clothing, and foot gear
suited for riding a motorcycle. Bright OR light
colors are best for greater visibility in traffic,
specially at night. Avoid loose, flowing garments
and scarves.
When carry ing a pi lli on ri der , it is your
responsibility to instruct them on proper riding
procedures.
DO NOT allow other individuals, under any
circumstances, to operate your motorcycle
unless you know they are experienced, licensed
riders and are thoroughly familiar with the
operating conditions of your motorcycle.
Warning
Regularly inspect shock absorbers and front forks
and look for leaks. Replace worn parts. Worn parts
can adversely affect stability and handling.
16
Warning
For your personal welfare, all the listed service and
ma in tenanc e rec om men dations sh oul d be
performed. Lack of regular maintenance at the
suggested intervals may affect the safe operation
of your motorcycle.
Warning
Avoid any contact with the exhaust system. Wear
clothing that will completely cover the legs while
riding. The exhaust system gets very hot when the
engine is running and remains too hot, even after
the engine is turned off. Failure to wear proper or
protective clothing could result in serious injury.
Warning
Exh aust g as es co nt ains poi s ono us c arbon
monoxide and chemicals, known to cause Cancer,
Birth Defects or other reproductive defects.
Safe Riding Tips / Guidelines
Warning
Mo to rcy cl e batt er ies c ont ai n l ead and lead
components, acids and chemicals known to cause
cancer, birth defects or other reproductive harm.
Exercise extreme caution while handling a battery.
Wash hands thoroughly whenever a battery is
handled.
Warning
Consult your Royal Enfield Dealer regarding any
questions or problems that occur in the operation
of your motorcycle. Failure to do so may aggravate
an initial problem, cause costly repairs & jeopardize
your personal safety.
17
Warning
DO NOT tow a disabled motorcycle. The steering
and handling of the disabled motorcycle will be
impaired due to the force of the towline. If a disabled
motorcycle must be transported, use a truck or a
trailer. Towing a motorcycle may cause loss of
control of the motorcycle in the front, leading to an
accident.
Warning
DO NOT pull a trailer behind a motorcycle. Towing
a trailer may cause reduced braking efficiency, tyre
overloading and unstable handling. Towing a trailer
may cause loss of control of the motorcycle in the
front, leading to an accident.
Safe & Happy Riding
RIDING DRESS
Please wear a proper riding apparel.
A pair of riding boots or shoes.
Soft leather gloves.
Goggles or spectacles to safe guard eyes.
A certified helmet. Affix light reflecting strips of
stickers at the front and rear.
NOTE :
A light coloured shirt enables greater visibility to other
road users specially during nights.
CAUTION :
Loose clothing may get caught on moving parts of
your motorcycle.
SITTING POSTURE
Correct sitting posture is a pre-requisite for stable
and safe riding
Sit Straight with your shoulders completely relaxed.
Keep your elbows close to your body.
18
Keep your toes in straight ahead direction.
Slightly grip the petrol tank with both knees.
Hold the handle bar grips, close to its inner end.
Look extensively ahead, including rear view
mirrors, without turning the head.
BRAKING
Ap pl y f ron t and rear br akes gently and
simultaneously for maximum braking efficiency.
WARNING
Applying any one of the brakes suddenly may cause
the vehicle to skid. The hydraulic disc brake fitted on
your motorcycle requires very less effort. High effort
or sudden application may lock the wheel. Please use
utmost caution while applying the brakes.
While riding on wet or bad road conditions use
brakes cautiously.
Avoid excessive banking, otherwise footrest
may touch the ground and cause instability.
Rules of the Road
Be sure your number plate is installed in the
position specified by law and is clearly visible
at all times.
Ride at a safe speed that is consistent with the
type of road surface you are on. Pay strict
attention to whether the surface is :
Dry
Oily
Icy
Wet
Watch for loose debris, such as leaves, slippery
substances or loose gravel that can hamper the
stability of your vehicle.
DO NOT exceed the legal speed limit or drive
too fast for existing conditions. Always reduce
speed when poor driving conditions exist. High
speed increases the influence of any other
condition affecting stability and increases the
possibility of loss of control.
19
Keep to the correct side of the road center line
when meeting oncoming vehicle.
Always sound your horn, actuate your turn
signals, and exercise caution when passing
other vehicles going in the same direction. Never
try to pass another vehicle going in the same
direction at street intersections, on curves, or
when going up/or down a hill.
At street intersection give the right-of-way to the
vehicle on your left or right. DO NOT presume
you have the right-of-way.
Always signal when preparing to stop, turn or
pass.
While turning either right or left, watch for
pedestrians, animals, as well as vehicles.
All traffic signs, including manual controls at
intersections, should be obeyed promptly .
SLOW DOWN at traffic signs near schools and
CAUTION signs at railroad crossings.
Rules of the Road
20
When intending to turn, signal at least 100 feet
(30.5 meters) before reaching the turning. Be
close to the center line (unless local rules require
otherwise), slow down and then turn carefully.
Never jump a traffic light. When a
change is imminent from GO to
STOP (o r v ice ve rs a) at
intersections, slow down and wait
for the light to change to green.
Never run through a yellow or red
traffic light.
SIDE VIEW MIRRORS
Red
Yellow
Green
DO NOT leave the curb or parking area without
signaling. Be sure your way is clear to enter
moving traffic. A moving line of traffic always
has the right-of-way.
Park your motorcycle on a firm and flat surface
to prevent it from falling over.
Protect your motorcycle against theft. After
parking your motorcycle, remove Ignition key
from switch and lock the steering head.
Your motorcycle is equipped with convex mirrors
and have a curved surface. This type of mirror is
designed to give a much wider view to the rear than
a flat mirror; however, cars and other objects seen
in this type of mirror will look smaller and farther
away than when seen in a flat mirror.
Use care when judging the size or distance of
objects seen in these mirrors.
NOTE :
To help you establish the relative distance of vehicles
behind your motorcycle, adjust each mirror in such a
way, that a small portion of your shoulder is visible and
a large portion behind your motorcycle is seen clearly.
Vehicle Identification
21
CHASSIS NUMBER
ENGINE NUMBER
Punched on the steering head tube
Punched on top of the engine LH side.
Key Parts Location
22
RIGHT SIDE VIEW
1
6
5
4
3
2
1.
RH Trafficator front
2.
Brake Pedal
3.
Starter Motor
4.
Utility Box
5.
Air Filter Box
6.
RH Trafficator Rear
Key Parts Location
23
1. Trafficator front LH
LEFT SIDE VIEW
2. Horn
3. Spark plug
4. Gear Change Pedal
5. Battery Cover
6. Side Stand
7. Centre stand
1
8. Trafficator rear LH
8
2
3
4
5
6
7
Key Parts Location
3 45 6
TOP VIEW
2
1.
2.
3.
4.
5.
Turn signal switch
Horn button
Clutch lever
Day flash switch
Head lamp dip switch
6.
7.
8.
9.
10.
24
7
8
9
10
1
Manual Bistarter / Choke
Ignition switch
Speedometer
Malfunction / Low fuel Indicator
Engine Kill switch
11
12
13
11. Pilot head light switch
12. E-Start Switch
13. Fuel tank cap
Operation of Controls
IGNITION SWITCH
25
STEERING LOCK
Turn key clockwise to lock.
Lock the s te eri ng wh en
leaving bike parked.
OFF
CAUTION :
Protect your motorcycle against theft. After parking your motorcycle,
remove the ignition key from switch and lock the steering head.
ON
DO NOT lubricate barrel locks with petroleum based lubricants or
graphite. Inoperative locks may result in damage to your vehicle.
Operation of Controls
26
FUEL TANK CAP
SIDE BOX
Turn key clockwise to open.
Press cap to lock with key in
position.
SIDE BOX LH
AIR FILTER BOX RH
Turn Key anti-clockwise to open
Turn Key anti-clockwise to open
NOTE :
Key can be removed only in
locked position.
Use high quality unleaded
high oc tane petrol (91
octane and above) for
enhanced performance.
NOTE :
Key is common for ignition, petrol tank cap, steering lock, side
boxes and battery cover.
Key for fuel tank and tool boxes can be removed from the lock
only in locked
Operation of Controls
BATTERY CARRIER
27
UTILITY BOX
Battery Box Cover
Turn Key clockwise & lift the battery box cover
gently
To remove cover turn key anti clock-wise and pull
the oval cover by applying finger pressure
Operation of Controls
28
HEAD LAMP SWITCH
HEAD LAMP OFF
HEAD LAMP DAY FLASH
PRESS FOR HEAD LIGHT FLASH
PILOT LIGHT ON
HEAD LAMP ON
DIP SWITCH
LOW BEAM
HIGH BEAM
Operation of Controls
ENGINE START SWITCH
29
ENGINE STOP SWITCH
PRESS
ENGINE ON
ENGINE OFF
TURN SIGNAL SWITCH
OFF (PUSH TO OFF)
LEFT
RIGHT
Operation of Controls
HORN
MANUAL BI STARTER (CHOKE)
PRESS
Apply choke in cold start condition while starting the Bike
30
Pre Operational Checks
31
A careful check of the following must be carried out every time before riding and specially after long periods of
storage to determine if additional maintenance is necessary.
1. Tyres for correct pressure, abrasions or cuts.
5. Engine oil level.
2. Rear chain for proper tension.
6. Wheel spoke for proper tightness, no breakage,
Drive Chain
MAX
MIN
Clutch
3. B r a k e s , s t e e r i n g
and th rott le f or
responsiveness.
4. Cable for fraying or
crimp ing and free
operation.
Spokes
7. Headlamp, tail lamp, brake lamp and indicator
lamps for proper operation.
Warning
For your personal welfare and safety, all the points
mentioned above should be performed periodically.
Failure to do so, may affect safe operation and damage
your motorcycle and could result in an accident causing
serious injury.
Running In Period
Proper running-in is v ery important for obtaining
maximum life and performance of a new motorcycle. The
following guidelines explain proper running-in
procedures.
Since the engine is brand new, it should not be loaded
excessively for the first 2,000 kms. During the first few
hundred kms, the various parts in the engine wear and
polish themselves to the correct operating clearances.
Driving with prolonged full throttle operation, or any high
speed conditions might result in excessive heating of
the engine and cause abnormal wear of the moving parts
and hence must be avoided.
1. 0 - 500 Kms :
The recommended speeds for the first 500 Kms is
below 50 Kmph. During this period avoid operating
the motorcycle with full throttle opening. Stop the
motorcycle for about 5 to 10 minutes to let it cool
down, after every hour of running. Vary the speed of
the motorcycle regularly during running but avoid
using the motorcycle above ½ throttle opening
position.
2. 501 - 2000 Kms.
The recommended speed is below 80 Kmph. Avoid
32
driving the motorcycle with full throttle opening. Vary
the speed of the motorcycle regularly but avoid using
the motorcycle above 3/4 throttle opening position.
3. 2,001 kms and above
Avoid prolonged full-throttle operation. Vary speed
occasionally.
CAUTION :
After covering the first 500 kms. please replace the
engine oil and oil filter element.
Royal Enfield engines are air-cooled and consequently
require forced air cooling over the cylinders and heads
to maintain proper operating temperature. Extended
periods of idling may over heat the engine, resulting
in serious engine damage.
DO NOT run the engine at extremely high RPM with
clutch disengaged or transmission in neutral as it can
cause serious engine damage.
An engine running long distances at high speed must
be given close attention to avoid over heating and
possible engine damage.
Electronic Fuel Injection & MIL
ELECTRONIC FUEL INJECTION (EFI)
An electronic control unit (ECU) monitors engine
performance and provides exact requirement of Air
/ Fuel mixture to the engine, through the fuel injector
by taking inputs from various sensors provided in
the motorcycle.
THE ADVANTAGES OF EFI ARE
Faster response of the engine to suit road/load
conditions.
Better power output
Lower emission
Better reliability
Excellent cold startability
Engine Diagnostic capabilities
Maintenance free
33
MALFUNCTION INDICATOR LAMP (MIL)
A Malfunctioning Indicator
Lamp (MIL) is provided in
the small meter located on
the right side of the head
lamp casing.
There are two indications
in this unit.
Low fuel indication & EFI Mal-function Indicator Lamp
(MIL). When both the Ignition & Engine kill switch is
“ON”, the MIL will glow for few seconds and will go
“OFF”. This indicates that all the functions of
Electronic Control Unit (ECU) and other sensors are
working perfectly and the motorcycle can be used.
Incase of any malfunctioning of the ECU or other
sensors etc., the MIL will glow continuously. In the
event of any such phenomenon, it is recommended
to take the vehicle to a nearest Royal Enfield
authorised service point for inspection and further
necessary action.
Rollover Sensor
ROLLOVER SENSOR
34
Your motorcycle is fitted with a unique “Roll Over
Sensor” under rider seat. This is a safety feature.
In the event of an accident OR if the motorcycle
falls over on its side with the engine running.
The “Roll Over Sensor” will switch off Ignition and
cut off fuel supply to prevent the motorcycle from
moving suddenly, if it is in gear.
To re-activate the system after the motorcycle has
been made upright, please switch off both the
Ignition & Engine kill switch, wait for a few seconds
and switch “ON” again.
This will help to RESET the “Roll Over Sensor” and
the engine can be started / run.
Starting
35
Warning
Before starting engine, always shift gears into neutral.
CAUTION :
Do not force the gear lever while attempting to shift to
neutral. Move the motorc yc le bac k & forth and
simultaneously press gear lever to come to neutral.
Ensure neutral indicator light comes “ON”’ in the
Speedometer.
Tu rn ig ni ti on
switch ‘ON’
NOTE :
If the engine does not start on the first attempt in
cold climate, release the starter button, wait for 30
seconds before pressing the starter button again.
Press starter button and release starter switch once
the engine starts.
Ensure the side
and main stands
are in released
position
A clutch switch is provided in the system for the
safety of the rider. This is to prevent the vehicle from
starting when the vehicle is in gear. To start the
engine when it is in gear, pull clutch lever, press
starter button and release as soon as the engine starts.
Ensure that gears
are in neutral and
neutral lamp is
glowing.
N
Starting
36
CAUTION :
Ensure Engine
stop switch is in
“RUN” position
Never accelerate the engine immediately after a cold
start. The engine should be allowed to run slowly for
15-30 seconds. This will allow the engine to warm up
and let oil reach all surfaces needing lubrication.
Failure to adhere may result in damage to the Engine.
Press Clutch
Lever.
Manual bi
(choke) Starter
NOTE:
Press Starter
Button and
release as soon
as engine starts
It may be necessary to operate and hold the manual
bi starter, when starting the engine for the first time in
cold mornings or at high altitudes, to prevent the
stalling and to keep the idling RPM steady.
Starting
37
As soon as the engine attains the operat ing
temperature, the RPM will raise, at which time the
manual Bi Starter should be released.
Warm up engine for 2 minutes - till idling is
consistent.
Prior to starting, check to see if the low fuel indicator
is glowing continuously.
CAUTION :
Please ensure the motorcycle is not used with the low
fuel indicator lamp “ON” continuously. It may not only
result in the motorcycle running out of fuel. But will also
cause serious damage to the fuel pump. Please ensure
fuel is filled up as soon as the low fuel lamp comes
“ON”.
USING KICK START
Sl ightl y c ra nk the e ngi ne
compression eases over.
Th is wi ll gl ow
continuously, if
the fuel level in
tank is below 2.5
litres approx.
fu rth er
ti ll
Start the
motorcycle with
a powerful
swinging kick.
Release the choke, if applied
Gear Shifting
38
Warm up engine
for 2 minutes ti ll id lin g is
consistent/stable
GE AR SH IFT PATTE RN
1
N
2
3
4
5
Press clutch lever towards the hand grip.
Press gear pedal with toe to engage 1st gear.
Gentl y open t hr ott le and r ele ase c lut ch
simultaneously. If clutch is released suddenly,
the engine may stall and cause a jerky start.
Pr es s t he gear
pedal with heel to
engage 2nd and
higher gear.
Follow the same
pr oc edu re f or
3rd, 4th and 5th
gear.
NOTE :
Always start motorcycle with gear in neutral position.
CAUTION :
Always move the motorcycle in first gear position only.
The clutch must be fully disengaged before attempting
a gear shift. Failure to fully disengage the clutch may
cause a jerky start and / OR stalling the engine besides
causing damage to transmission parts.
When engine speed decreas es, while climbing a
gradient or running at a reduced speed, shift to the
appropriate lower gear to prevent the engine from
stalling or straining to pull.
Parking
PARKING VEHICLE ON CENTER STAND
Select a firm, flat surface
Hold handle bar straight
Lower center stand, and ensure that both the
legs of the stand are resting evenly on firm ground.
Apply pressure on the fulcrum lever on the
center stand and pull vehicle backwards, gently.
39
PARKING VEHICLE ON SIDE STAND
Select a firm, flat surface
Lower Side Stand and gently tilt motorcycle to
the left till it rests firmly.
Warning
Always park the motor cycle on a firm and flat surface. Parking in a soft ground may cause stand to sink and the
motorcycle to fall, causing injury to you or to others and damage to the motorcycle parts.
Tools & First Aid Kit
1
2
3
4
5
6
7 8
9
40
5
10
7
6
1
S.No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Description
Tool bag
Box spanner 21 X 24
Screw driver O6 X 160
Double end spanner 1/4 X 5/16
Double end spanner 10 X 12
Tool- Spark plug
Tommy bar
Tubular spanner 12 X 13
Single end ring spanner - 17
Extension tube
Qty.
1
1
1
1
2
1
1
1
1
1
4
S.No.
1.
2.
3.
4.
5.
6.
7.
3
Description
2
Qty.
Antiseptic cream 5 gms
Gauze bandage 5 cm x 2 cm
Elastic Gauze bandage 8 cm x 1 mtr.
Wash proof plaster 1.9 cm x 7.2 cm
Sterilized Gauze Swab 5 cm x 5 cm
Sterilized elastic plaster 7 cm x 6 cm
First aid kit pouch
1
1
1
2
2
1
1
NOTE :
This Tool Kit is kept in Utility box. Refer Page No. 27
Recommended Lubricants
Engine Oil
Grade
Royal Enfield 15 W 50 API SL Grade
Engine Oil
(JASO MA)
Grade
41
Front Fork Oil
Royal Enfield
Front Fork Oil
(or 1F Grade
Endurance)
Capacity
195 ml/leg
Brake Fluid
Grade
DOT 3 or DOT 4
Capacity
60ml
ISO 14001 – EMS
Operation Control Process
Capacity
2.75 Ltrs. (with oil filter)
2.50 Ltrs. (during oil & filter element
replacement)
1. All customers are advised timely replacement of Engine Oil,
Fork Oil & Brake Oil at the dealership /ASP. In case done
privately, it is advise to reach old/used Oil to our authorised
vendor through RE Dealer/ASP
2. Similarly we advise for disposal of old/used Battery, Tube
& Tyres as mentioned in above point No.1.
Warning
DO NOT switch oil brands indiscriminately because some oil interact chemically when mixed.
Use of inferior oils or non-detergent oils can damage the engine.
DO NOT Mix DOT 3 & DOT 4 brake fluid together.
Periodical Maintenance
42
The maintenance schedule detailed here will help you to maintain your Classic 500cc meticulously and to get a long
trouble free service. The schedule provided herein is based upon average riding conditions and indicates the mileage
at which regular inspections, adjustments, replacements and lubrications must be carried out.
The frequency of the maintenance must be shortened depending upon the severity of the driving condition OR if the
motorcycle is used in a very dusty environment, severe climatic cold and hot conditions, bad roads, stagnant water
etc., Contact a nearest Royal Enfield Authorised Dealer / Service Point for expert advice and to carry out the
periodical maintenance.
Warning
For your personal welfare, all the listed service and maintenance recommendations should be performed. Lack of
regular maintenance at the suggested intervals may affect the safe operation of your motorcycle causing the motorcycle
to malfunction and stall abruptly resulting in an accident and cause serious injury.
Periodical Maintenance
S.
No.
1
43
FREE SERVICE
whichever is earlier
DESCRIPTION
Kms (x 1000)
0.5
3
6
9
Months
1.5
3
6
9
I
R
I
Engine Oil
R
PAID SERVICE
12
15
18
21
24
27
30
R
I
R
I
R
I
R
Check level at every 1000 Kms or earlier as required
2
Engine oil filter element
R
C
R
R
R
R
R
3
Engine sump filter (oil strainer)
C
C
C
C
C
C
C
4
Magnetic drain plug under gear box and secondary
drain plug under crankshaft in crankcase RH
C
C
C
C
C
C
C
5
Spark plugs (2 nos.)
6
HT leads for crack
I
I
I
I
I
I
I
I
I
I
I
7
Fuel hose & clip / Injector ‘O’ Ring / Seal Ring
I
I
I
I
R
I
I
I
R
I
I
8
Fuel Pump (under tank)
9
Accelerator & Throttle pully cable free play
C&A C&A C&A C&A C&A
R
C&A C&A C&A C&A R
Check for screw tightness in all services
A
A
A
A
A
A
A
A
A
A
A
10 Rubber hose, Air filter to Throttle body
I
I
I
I
R
I
I
I
R
I
I
11 Rubber hose, Inlet manifold / Adaptor
I
I
I
I
R
I
I
I
R
I
I
Periodical Maintenance
S.
No.
44
FREE SERVICE
whichever is earlier
DESCRIPTION
Kms (x 1000)
0.5
3
6
9
Months
1.5
3
6
9
C
C
C
C
12 Air filter paper element
PAID SERVICE
12
15
18
21
24
27
30
R
C
C
C
R
C
C
13 Inlet / Exhaust valve seating
I
I
14 Cylinder head (Combustion chamber)
D
15 Clutch lever free play
Adjust every 1000 Kms or earlier as required
16 PAV pipes & hose clip
I
I
C
I
C
I
C
I
C
I
17 Rear brake pedal pivot
L
L
L
L
L
L
L
L
L
L
L
18 Battery terminals (apply petroleum jelly)
C
C
C
C
C
C
C
C
C
C
C
19 Battery Electrolyte level
I
I
I
I
I
I
I
I
I
I
20 Earth wire eyelet (behind battery carrier)
I
I
22 Rear Wheel Drive Chain
Adjust for every 1000 Kms / Clean, Lubricate & adjust
every 3000 kms or earlier as required
24 Rear brake cam
I
R
I
I
I
21 Front Fork oil / leak
23 Rear brake pedal free play
I
C
I
I
R
I
I
I
Adjust every 1000 Kms or earlier as required
L
L
L
L
L
Periodical Maintenance
S.
No.
45
FREE SERVICE
whichever is earlier
DESCRIPTION
Kms (x 1000)
0.5
3
6
9
Months
1.5
3
6
9
A
L
A
25 Steering ball races / play adjustment
26 Spokes tightness / Wheel rim run out front & rear
I
27 Swing Arm pivot bush & spacer
PAID SERVICE
12
15
18
21
24
27
30
R
A
L
A
R
A
L
I
I
I
I
I
L
L
L
R
L
28 Rear wheel cush rubbers
I&R
29 Tyre wear (Front & Rear)
I&R
I
I
I
I
I
I
I
I
30 Brake Oil level check / Replacement
I
I
I
I
I
I
I
I
R
I
I
31 Pivot-Side Stand, Center Stand, Pillion Foot Rest
L
L
L
L
L
L
L
L
L
L
L
Carbo Cleaner / Carb Click or Fuel Line Cleaner Spray
Every 6000 Kms or 6 Months whichever earlier
32 Throttle body / Injector
33 Hand levers & kick starter lever pivot
A : Adjust
C : Clean
I
D : De-carbonise
Lubricate every 1000 Kms or earlier as required
I : Inspect
L : Lubricate
R : Replace
NOTE :
For maintenance after 30,000 Kms, please repeat the same frequency levels specified above, in consultation with a
Royal Enfield Authorised Dealer / Service Point.
Minor Maintenance Tips
The following minor maintenance can be carried out
easily with simple tools. However, In case, if it is
felt that the adjustments are best done by an expert,
we recommend that the motorcycle be taken to a
nearest Royal Enfield Authorised Dealer / Service
Point.
CONTROL CABLES, HANDLE BAR LEVER, PIVOTS,
CENTER / SIDE STAND PIVOTS
46
OIL LEVEL INSPECTION
MAX
MIN
Lever Pivot
Main & Side
Stand Pivot
Lubricate after using the motorcycle in rain,
after waterwash or if used in dusty conditions.
Place motorcycle on its center stand on a firm
surface.
Warm up engine for a few minutes & switch off
Wipe the area free of dirt / grease.
The level is correct if the oil level is in the
middle of the oil level window.
Apply a few drops of oil on the pivots.
Top up with recommended oil if required.
Minor Maintenance Tips
47
ENGINE - OIL CHANGE
Secondary
Primary
Drain Plug Primary
Drain Bolt
Drain Cap
TILT VEHICLE
(Refer Periodical Maintenance Chart for frequency)
Place motorcycle on its center stand on a firm
flat surface.
Start engine and warm up for 2 minutes.
Keep a clean tray below the engine
Remove primary drain cap, to drain oil & clean
suction filter, magnet.
Then remove secondary drain plug to drain oil
& clean the magnet.
Finally remove primay drain bolt to drain the
complete oil.
Remove the oil filter element on the Crankcase
Cover RH.
Allow the oil to drain by tilting the motorcycle
to both sides.
Wash the primary and secondary drain plugs
along with suction filter thoroughly and refit on
the crankcase after all the oil is drained out.
Minor Maintenance Tips
Soak a new oil filter element in the oil and refit
on the Crankcase Cover RH.
Assembly 3 bolts and tighten them. Ensure ‘O’
Ring and gaskets are taken seat properly.
Fill recommended
oil to engine till
the oil level is
upto “MAX” level
mark in the oil
window in Crankcase Cover RH.
Max
NOTE :
Min
Replace oil filter element whenever oil is being
replaced.
CAUTION :
Filling up oil over MAX mark may cause smoke and /
or loss of power. Do NOT allow oil level to fall below
MIN mark. Doing so may result in engine internal
damage or malfuncton.
48
SPARK PLUG
Gap 0.70 to 0.80 mm
Cleaning and adjusting gap (Refer Periodical
Maintenance Chart for frequency)
Remove HT Lead and the spark plug from the
cylinder head using the plug spanner and
tommy bar.
Clean the insulator tip and electrodes of the
plug carefully using a pointed scraper or spark
plug cleaner.
Set the gap between 0.70 to 0.80 mm.
Refit the spark plug on the cylinder head and
connect H.T. Lead.
Minor Maintenance Tips
BRAKE FLUID
49
INSPECTION OF TYRES AND WHEELS
Inspect the tyre periodically for
tread wear, cracks and cuts.
Minimum tread depth :
MAX
MIN
Front tyre : 1mm Rear tyre : 2 mm
Check and remove stone, splinters,
nails or other particles embedded in
the tyre treads.
Check if oil is above ‘min’ level. To top up, remove
cover and diaphragm and top up with either DOT 3
or DOT 4 as specified.
Bald spots / swelling may be caused by internal
damage. Replace the tyres, if defective.
CAUTION :
Replace tyres when the tread depth has reached
the minimum as specified.
Please take care that it does not spill over any other
parts of the motorcycle. Please wipe the spilled
brake fluid immediately, if there is any spill over,
using a soft cloth (preferably a wet cloth) to avoid
damage to paint work or other parts.
Don’t mix DOT 3 & DOT 4 Brake fluid together.
Periodically inspect wheels for spokes breakage
and wheel rim run out.
Check proper seating of the tyre beading on the
rim whenever the tyre is reassembled.
Minor Maintenance Tips
Whenever a new tyre is installed, ensure rim
and spokes do not get damaged on account of
using wrong levers.
Use only standard tyres & tubes inflated to
correct pressure.
TYRE PRESSURE
Frontt
Solo
With Pillion
Rear
1.41 kg/cm2
(20 PSI)
2.11 kg/cm2
(30 PSI)
1.55 kg/cm2
(22 PSI)
2.25 kg/cm2
(32 PSI)
Warning
Tyres, rims and air valves must be correctly matched
to wh eel rims . See y our Roy al E nfield De aler.
Mismatching tyre, tubes, rims and air valves may result
in damage to the tyre bead during mounting, allow tyre
slippage on the rim and cause tyre failure.
50
FRONT WHEEL REMOVAL
Place the vehicle on center stand
Place a wooden block
th e fro nt end of
engine to support the
vehicle.
Dis c onnec t s peedo
cable.
Loosen the pinch bolt
on the RH fork guide.
Hol d f r ont ax l e by
spanner and loosen
axle nut then remove
nut along with washer.
Minor Maintenance Tips
Tap and remove the front wheel spindle.
Tilt the vehicle to RH Side and take out the wheel
along with speedo drive with bush & LH side spacer.
.
51
FRONT WHEEL ASSEMBLY
Remove the wooden piece / card board sheet
placed between the brake pads
Pl ac e t he sp ee do
dr iv e
b us h
in
position and place
speedo drive over it.
Ta ke out S pee do
drive and bush on
th e RH sid e as
shown in pic.
CAUTION :
Do not press the front brake lever when wheel is
removed as this will result in the brake pads coming
too far out of the brake caliper.
Place a 4 mm thick wooden piece or cardboard
sheet between the brake pads to avoid pads
activation in the event the front brake lever is
accidently pressed.
In s ert th e w heel
along with speedo
drive assembly and
LH spacer between
the front fork ends
ensuring the brake
disc is located in
between the brake
pads.
Insert and tap the
fr on t whe el ax le
gently inside.
Refit the washer and
tighten the nut firmly.
Minor Maintenance Tips
52
REAR WHEEL REMOVAL
Place the vehicle on center stand on a firm and
flat surface.
Note and mark the position of the chain adjuster
butt ing
with
t he
stopper on the right side.
Tighten the pinch bolt on the RH fork guide.
Rotate the wheel and check for smooth rotation.
Connect the speedo cable to speedo drive unit
and rotate the wheel to check for proper
working of speedo meter.
Press brake lever 2 or 3 times to check front
brake efficiency
NOTE :
Ensure that the speedo drive is correctly located such
that the cable can be connected without difficulty.
Remove split pin and
castle nut on the RH
side.
Remov e
wheel
spindle from LH side
al ong wit h c ha in
adjuster, taking care
not to drop the wheel
c olla r and s pac er
from the LH side of
the wheel.
Tilt vehicle to RH
side and slide out
rear wheel.
Minor Maintenance Tips
REAR WHEEL ASSEMBLY
Ensure the four cush rubbers are in position
inside the rear wheel hub.
53
Ensure that the chain adjuster knotch butts with
the stopper as appropriate when both the front
& rear wheels are aligned.
Tighten the castle
nut fir mly
and
ensure that the hole
on axle shaft and
the slot on castle nut
ar e ali gned to
enab le split p in
fitment.
Tilt vehicle to right
and insert wheel
assembly between
the swing arms.
Po sit io n t he re ar
wheel wi th cu sh
rubber on the rear
chain sprocket.
Hold wh eel coll ar
and
spa cer
in
position.
Assemble the wheel
spindle along with
chain adjuster from
the LH side of vehicle
and g ently tap it
through the wheel.
Fix the split pin.
CAUTION :
Do not force the spindle into the wheel as the threads
may get damaged. Tap it through the wheel gently.
Warning
Ensure the vehicle does not come off center stand while
assembling / disassembling the wheel assembly. Failure
to adhere could result in damage or serious injury.
Minor Maintenance Tips
ADJUSTMENTS - CLUTCH
54
DRIVE CHAIN FREE PLAY (PLAY 25 - 30 MM)
2 to 3 mm
A
B
Clutch Lever (free play 2 to 3 mm)
Clutch Free Play Adjustment
Remove rear wheel
split pin.
Loosen castle nut,
spindle nut, anchor
nut and brake rod
nut.
Loosen the cable outer lock nut (A).
Turn the Nut (B) Clockwise to reduce the play
or Anticlockwise to increase the free play.
Check free play 2 to 3 mm at Clutch lever pivot
on handle bar end.
Tighten lock nut (A) after adjustment is done.
Turn the RH adjuster
cam as appr opriately, till 25 to 30
mm s l ac k ne s s is
achieved on the top
run of the chain.
Minor Maintenance Tips
Check brake pedal free play, If necessary
adjust.
55
CHECKING REAR BRAKE PEDAL HEIGHT
Check that the front
and rear wheels are
correctly aligned.
Turn the LH adjuster
cam appropriately, to
align both the wheels.
Chec k a nd ens u re
that the knotches on
the cam are resting
on the pin in t he
swing arm on bot h
sides.
Loosen the lock nut.
Ap ply br ak e a nd
tighten all nuts.
Turn in or out the pdeal stop pin bolt till the
brake pedal and front footrest are in the same
height / level as shown in above fig.
Fi na lly Tor que t he
anchor Nut.
Tighten the lock nut
Check for free rotation of rear wheel.
Minor Maintenance Tips
REAR BRAKE FREE PLAY ADJUSTMENT
56
CHAIN LOCK FITMENT
20 - 30 mm
Turn in or out the adjuster nut at the brake rod end.
The recommended brake pedal travel is 20-30 mm.
Check that the brake is not binding and the rear
wheel rotates freely.
The open end of the chain lock to face opposite to
normal direction of chain rotation
Warning
Please ensure brakes are adjusted to their maximum
efficiency. Inefficient brakes can cause an accident.
Please ensure adequate caution while applying brakes. Sudden
application OR pressing the levers fully can caused the wheels
to lock. This may cause the motorcycle to skid with possible
loss of control and result in an accident causing. Brake shoes
must be inspected for wear every 4000 Kms. If you ride under
adverse conditions, (steep hills, heavy traffic, etc.) a more
frequent inspection at 1600 Kms or less, is required.
Warning
The fitment in wrong direction can lead to falling off
of chain link thus disengaging the drive. This will
lead to potentially hazardous situation which, if not
avoided, could result in serious injury.
Minor Maintenance Tips
57
Turn the adjuster such that the adjuster moves
up to increase the spring tension and vice versa
to reduce the spring tension.
ADJUSTMENT OF GAS SHOCKABSORBER
Adjust both left hand and right hand shock
absorbers so that the same notch rests on the
pin in both sides.
Warning
RH
LH
The rear gas shock absorber is of adjustable type
i.e., the spring tension can be increased or
reduced.
Riding the motorcycle with the notches adjusted in
different positions can cause loss of control and may
lead to an accident.
Regularly inspect shock absorbers and front forks for
leaks. Replace worn parts. Worn parts can adversely
affect stability and handling.
Increase the spring tension for high load operation.
Reduce the spring tension for low load operation.
NOTE :
The adjuster provided on the bottom of the
spring has five notches.
Ensure no fouling of any accessories with rear shock
absorber. Check for sufficient gap availability between
the shock absorber and the attachments when the rear
end of the motorcycle is fully loaded and the shock
absorbers are fully compressed.
Insert s pec ial ‘C’ spanner on the bottom
adjuster and rotate to change knotch position.
Minor Maintenance Tips
REMOVAL OF BATTERY FROM THE VEHICLE
The vehicle is provided with 12V - 14 AH
battery.
Unlock (turn the key clockwise) and remove the
battery cover.
Remove the battery holding two rubber straps
gently.
Pull out the battery and turn, then disconnect
both the terminal wires (negative and positive
respectively)
Take out the battery.
58
BATTERY MAINTENANCE
The battery must be periodically checked for
Cleanliness and corrosion free terminals.
Electrolyte level.
If electrolyte level is low, top up with
distilled water only.
Apply petroleum jelly over the battery terminals
to avoid sulphation.
NOTE :
Incase of poor contact or loose fitment of Battery
terminals may cause the failure of ECU.
Minor Maintenance Tips
Warning
Always disconnect the negative (-) battery cable first
and then the Red positive (+) cable while removing
the battery connections.
NOTE :
For checking the battery v oltage and elec troly te
specific gravity, contact authorised Royal Enfield
service or battery service centre.
CAUTION :
Do not use battery with low electrolyte level as the
battery internals cells will get damaged.
Do not overfill the battery electrolyte level as it will
spill out through the overflow pipe and cause
corrosion to vehicle parts.
Use only distilled water meant for use in batteries
to avoid damage to battery.
Electrolyte should not be filled when the level is
between minimum & maximum levels indicated in
battery as “MIN” & “MAX”.
59
ASSEMBLY OF BATTERY ON VEHICLE
Position the battery in the battery carrier such
that the negative terminal of the battery is
towards fuel pump.
Ensure ignitiion switch is in ‘OFF’ condition.
Connect the positive terminal (Red wire) first.
Connect the negative terminal (Black wire) next.
Smear the terminals with petroleum jelly. (Do
not use grease).
Refit the rubber strap bracket to hold the
battery.
Refit LH side panel.
NOTE :
Clean the wire terminals free of corrosion and keep
the terminals coated with petroleum jelly.
CAUTION :
Connect the +ve and -ve cables to the respective
battery terminals. Failure to do so may result in damage
to the motorcycle electrical system.
Minor Maintenance Tips
CHANGING ELECTRICAL COMPONENTS
HEADLAMP BULB REPLACEMENT
Loosen the head lamp
holding top screw. Then
pull out head lamp
assembly.
Detach bottom lug from
the head lamp housing
body.
60
Remove rubbergrommet
from the reflector
assembly
Gently pres s the bulb
holding U clip from both
the s ides downwards
and rel eas e it fr om
reflector slot as shown.
Pull out head lamp bulb
and inspect its filament
for fuse
CAUTION :
Disconnect head lamp
wire connectors Green,
Orange and Blue Color
terminals.
Never touch the bulb with your
fingers, Finger prints will etch the
glass and decreas e bulb life.
Always hold the bulb with paper
or clean dry cloth during handling.
Minor Maintenance Tips
61
ASSEMBLING THE HEADLAMP
Connect the wire couplers
as mentioned below
TOP SIDE: GREEN COLOUR
RIGHT SIDE: BLUE COLOUR
Refix the new head lamp
halog en bulb
in to
reflector unit by locating
the wide protrude on top
side mounting.
Fix bulb holding ‘U’ clip
in to reflect or body
knotch, then press the
both ends of clip and
lock in its slot.
LEFT SIDE: ORANGE COLOUR
Position the reflector ring
bottom lug into head lamp
cas ing slot and slide it,
th en t igh ten t he t op
mounting screw.
NOTE :
After connecting above said procedure, turn ignition
switch to “ON” condition and then check, ensure
that flash light working in HIGH BEAM mode.
Fit the rubber grommet.
If you use the bulb other than specified rating (12V
55/60W) may result in over loading electrical system
lead to premature failure or frequent battery
discharge.
Minor Maintenance Tips
TAIL LAMP BULB REPLACEMENT
62
TRAFFICATOR BULB REPLACEMENT
Remove the 2 screws
& take out trafficator
glass cover.
Remove the two nuts
each from RH & LH
si de of t he rear
number plate holder.
Press bulb gently &
Turn anticlockwise to
take out the bulb.
Pu ll out T ail La mp
assembly along with
bracket and twist the
bulb
holder
in
anti clock wis e
to
remove bulb holder
assembly.
Position the new bulb
in si de th e hol der,
ensuring that the pins
in t he bu lb , m at ch
with the slots in the
holder.
Turn old bulb to remove
and replace with a new
bulb.
Pres s the bulb and
turn clockwise to lock
the bulb in the holder.
Refit the bulb holder
and turn clockwise to
lock the bulb holder.
Ref i t t he ta il la mp
with bracket on the
reve rse o rde r of
removal process.
Cut Mark
Refit the traffic ator
cover cut s lot mark
fa ci ng do wnwar ds
and t ig hten t he 2
screws.
Minor Maintenance Tips
FUSE
63
BLADE FUSE USAGE LIST
Fuse No.
ECU
6
54
32
1
Color
Remarks
1
Blue
Main Fuse (15A)
2
Red
EFI / ECU Fuse (10A)
3
Red
Lighting Circuit Fuse (10A)
4
Red
Signaling Circuit Fuse(10A)
5
Blue
Spare Fuse (15A)
6
Red
Spare Fuse (10A)
Warning
Open the LH tool box Ref. Page No. 26.
The fuse holder is located inside with 4+2 fuses.
Replace the required fuse with the spare fuse
available in the fuse carrier.
Please ensure to replace a spare fuse in the holder
at the earliest opportunity.
Electronic Control Unit (ECU) may fail due to
a. Loose electrical / sensors wire connectors / couplers
or Battery terminals.
b. While do ing Arc weldin g on Motorcy cl e, it is
rec ommended to “SWITCH O FF” ignition and
disconnect the Battery terminals & ECU coupler from
Main Wiring Harness.
Minor Maintenance Tips
AIR FILTER PAPER ELEMENT
CLEAN AND REFIX : EVERY 3000 KMS
Insert the key, turn
anti cl ok wis e to
remove RH side air
filter box lid.
64
Tap the air filter element to remove dust as
s hown
an d
c lean
th oro ughly
be fore
assembly.
Clean intake duct and
inside filter box
as shown in pic.
Loosen the filter box
cover holding nut by
10mm spanner as
shown in pic.
Remove the nut,
washer and b ox
cover, to p c ov er
filter to take out air
filter element.
Assemble the filter
element, top cover and
filter box cover in the
reverse order of
dismantling process.
Please ensure proper
sealing of cover against
air filter element / box.
Pillion Seat Removal & Refitting
65
PILLION (REAR) SEAT REMOVAL
(A)
(A) Loos en
front
mounting nut of the
rear seat under the
ride r seat with
12mm
t ubular
spanner.
(B)
(B) Loosen both LH and
RH shock-absorber
top mounting nuts by
holding the bolt with
3/8” x 15/16” double
end spanner and
turning the doom nut
with 17mm eyelet
spanner
(C)
(C) Pull out the front
mounting bolt of the
rear seat from the
bracket under the
rider’s seat.
(D)
(E)
(D) Pull the rear seat
with its sub frame
towa rds bac k s o
that it will become
free from the shock
absorber mounting
bolts.
(E) Take out the rear
seat sub assembly
(F) Re-tigh ten
the
shock a bsorber
mounting bolts &
nuts before using
the vehicle.
Pillion Seat Removal & Refitting
66
PILLION (REAR) SEAT REFITTING
(A)
(B)
(A) Loosen
shock
absorber
upper
mounting nuts and
place the pillion seat
in the position over
the rear mudguard,
inserting the front end
of its sub frame goes
to its mounting under
the rider’s seat.
(B) Ensure the slit of
rear
mo unting
brackets are seated
properly in the LH &
RH shock absorber
mounting bolts.
(C)
(C) Inse rt the f ront
mountin g
bolt
thr ough
the
bracket under the
rider seat.
(D)
(D) Tight en the f ront
mounting nut with
12mm
t ubular
spanner holding the
bolt wi th 13mm
double end spanner
from other side.
(E)
(E) Tighten both LH &
RH rear shoc k
abs orb er
top
mounting bolt and
nuts.
Washing Procedure
PRECAUTIONS
Wash vehicle when the engine is cold.
Cover the silencer tail end and control switches with
suitable plastic bags and tie it firmly to prevent water
entry into them.
Remove ignition key and seal key hole using
adhesive tape.
Use a suitable engine degreaser, available with your
local parts store, to remove dirt or grease from the
engine external parts if required. Follow the
directions in the label carefully before using the
degreaser.
Use low pressure jet of water to clean the entire vehicle.
Never spray water with great force on head lamp,
speedometer, trafficator lights, front and rear wheel
hubs, electrical connections and wires, control
cables, EFI components, sparkplug, battery, etc.
Use luke warm water and mild detergent on the
painted components to remove dirt, etc.
Rinse vehicle thoroughly with plain water to remove
the detergent and wipe vehicle dry.
If possible, use compressed air and blow off water
particles from the obscure areas of the vehicle,
electrical connections, EFI components etc.
67
AFTER WASHING
Ensure, the vehicle is throughly dry by wiping with
a clean soft absorbent cloth or chamois leather.
Remove all plastic bags and adhesive tapes.
Lubricate control cables, pivot and rear chain with
lube oil
Polish the painted surfaces using polishing wax.
Start the bike allow engine to idle and warm up.
Drive the motorcycle slowly, applying both brakes
intermittently to dry up the brake shoes.
Test brakes for full efficiency.
Warning
Observe warnings and cautions given on labels of
cleaning compounds.
When washing your motorcycle, be careful not to get
the brakes, engine, mufflers or air cleaner etc., too wet.
Storage Precautions
Incase your Motorcycle is not going to be used for
a month or m ore , we adv is e t he follo wi ng
precautions to the taken.
Carryout required repair / adjustments on the
motorcycle.
Wash the motorcycle thoroughly and lubricate
as per the maintenance chart.
Start the engine, warm up for a few minutes
and switch off.
68
Remove battery from the bike. Clean the
terminals free of corrosion.
Maintain electrolyte level between max or min
mark, by adding distilled water and wipe the
battery dry.
Store the battery in a c ool, dry and well
ventilated place.
Do not place the battery in direct sun light, near
open flame or where temperature is above 40oC
or below 0o C
Drain out the fuel completely from the fuel tank
and fuel lines.
Cover the silencer with plastic bags to prevent
moisture entry. Set the motorcycle on its center
stand.
Remove spark plug. Pour in about 25ml of clean
engine oil through spark plug hole. Close the
hole and crank engine several times and refit
sparkplug.
Apply anti rust solution on all chrome plated
parts. Take care not to apply this solution on
rubber or painted parts.
Clean rear chain thoroughly and apply a thin
film of lube oil.
Store motorcycle in a clean covered area free
- of moisture and keep it covered to prevent
dust settling on it.
Storage Precautions
69
Remove anti rust solution from all chrome
plated parts and clean the motorcycle.
in a few drops of engine oil. Crank engine a
few times to lubricate cylinder walls and piston.
Clean spark plug and refit.
Inflate the tyres to the correct tyre pressure.
Switch “ON” ignition switch.
Ensure battery is fully charged and proper
electrolyte level is maintained.
Start vehicle and warm up engine for a few
minutes before riding the vehicle.
PREPARING THE MOTORCYCLE FOR REUSE
Connect the battery.
Lubricate all control cables and pivots.
Check proper level of oil in engine.
NOTE :
Fill fuel tank with fresh petrol.
Do not raise the engine rpm the moment it is started,
but allow the engine to run at idling speed.
Check fuel line for any cracks or cuts.
Clean the air filter.
CAUTION :
Remove plastic covering from the silencer.
Proper long-term storage is important for the safe,
trouble-free operation of your Royal Enfield motorcycle.
Remove spark plug on cylinder head and pour
Long Trip Precautions
CHECKS PRIOR TO THE COMMENCEMENT OF LONG
JOURNEY
Service the motorcycle thoroughly at Royal
Enfield Dealer / Authorised Service Point as per
periodical maintenance chart. (Ref. Page No.
43, 44 & 45)
Sufficient quantity of petrol in the fuel tank for
the journey planned.
Check and correct tyre pressure if necessary.
70
ITEMS TO BE CARRIED
Tool kit.
First aid kit.
Bulbs for Headlight, Trafficator light, Rear Tail
Lamp and Blade Fuse (10 & 15 Amps).
Accelerator, Choke, Clutch and Speedo Cable.
Rear chain master link lock assembly.
CHECKS AFTER EVERY 1500 KMS OF RUN
Tightness of all fasteners.
Tyre tread condition and wear of tyres.
Battery condition and electrolyte level.
Correct oil level in engine.
Working of all lights and horn.
Proper drive chain tension.
Sp ar e t ube, pun cture re pai r kit - co ld
vulcanising type.
Foot operated Air Pump.
Insulation tape.
Spark plugs (M14 & M10), Fuel hose.
Complete Wiring Diagram
71
NOTE :
Complete Wiring Diagram is attached on this page.
VEHICLE STARTING PROCEDURE
Basic Guidelines to be followed “FOR ALL ELECTRIC START VEHICLES”
1.
When ignition key is switched “ON”, please wait until the malfunction indicator lamp (MIL) goes
off, before attempting to start.
2.
In cold condition of the engine or for initial start, it is advised to use electric start (ES) only.
3.
Apply choke in cold start condition. (ambient temperature <25°C)
4.
DO NOT ATTEMPT – “HALF START” BY CASUALLY PRESSING ELECTRIC START BUTTON.
5.
PLEASE PRESS AND HOLD ELECTRIC START BUTTON FOR ATLEAST 3 SECONDS
CONTINUOUSLY FOR THE CRANKING OR UNTIL THE ENGINE FIRES AND SUSTAINS,
WHICHEVER IS EARLIER.
6.
If engine doesn’t start in the first attempt, release the ES button and repeat the above procedure.
7.
It is advised not to apply excessive throttle during starting.
Trouble Shooting
72
Warning
Warning
The trouble shooting section of this Owner’s Manual is
intended solely as a guide to diagnosing problems.
Carefully read the appropriate sections of this manual
before performing any work. Repair and maintenance
operations not listed in this Owner’s Manual should be
performed by your Royal Enfield Dealer only. Improper
repair and/or maintenance could result in the motorcycle
not functioning properly or serious injury.
CAUSES
Electronic Control Unit (ECU) may failure due to the
following reasons.
a. In c as e of loose electric a l / sens or s wire
connectors / couplers or Battery terminals.
b. While doing Arc welding on Motorcycle, its is
rec om mended to “SWITCH OFF” igni tion,
disconnect the Battery terminals & ECU from Main
Wiring Harness.
REMEDIES
I. ENGINE FAILS TO START
1)
Stop switch in ‘OFF’ Position ..........
Push stop switch to ‘ON’ position.
2)
Vent hole clogged in fuel tank cap ..
Clean vent hole.
3)
Spark plug cap / lead not connected
Fix cap / lead firmly
4)
Spark plug electrode dirty / fouled ..
Clean spark plug
5)
Spark plug insulation cracked .........
Replace spark plug
6)
Clutch slipping ..................................
* Adjust clutch cable free play
* Contact Authorised Dealer / Service Point
Trouble Shooting
CAUSES
73
REMEDIES
II. ENGINE MISFIRING
1)
Water in petrol tank .........................
* Clean petrol tank. Fill tank with fresh petrol.
2)
Loose spark plug cap .......................
Fix cap / lead firmly
3)
Spark plug fouled .............................
Clean spark plug or non specified heat range plug.
4)
Any sensor loose connections .........
connections
* Chec k MAP or EOT or TPS s ens or wiring/coupler loos e
III. POOR PICKUP
1)
Accelerator cable free play excessive
Adjust cable free play
2)
Choked air filter ................................
Clean / Replace air filter
3)
Brakes adjusted too tight .................
* Re-adjust properly
4)
Rear chain adjusted too tight ..........
* Re-adjust properly
5)
Clutch Slipping .................................
* Adjust clutch cable free play
6)
Under inflated tyres ..........................
* Inflate to correct pressure
* Contact Authorised Dealer / Service Point
Trouble Shooting
CAUSES
74
REMEDIES
IV. WHITE/BLUE SMOKE
1)
Oil level in sump above the Top line.
in the oil level window ......................
* Check and drain excess oil
* Worn out valve stem oil seal
V. ENGINE OVERHEATING
1)
Cylinder fins not clean .....................
2)
Clutch slipping ..................................
Clean the cylinder fins at regular intervals
* Check and correct
3)
Low engine oil level .........................
Check and top-up if necessary
VI. EXCESSIVE FUEL CONSUMPTION
1)
Fuel leakage .....................................
* Check and rectify
2)
Choked air filter ................................
Clean / Replace
3)
Under inflated tyres ..........................
Inflate to correct pressure
3)
Sticky (Choke) Bi-starter valve ........
* Check and rectify
* Contact Authorised Dealer / Service Point
Trouble Shooting
CAUSES
75
REMEDIES
VII. BRAKES POOR
1)
2)
3)
4)
Not adjusted properly .......................
Oil/grease on lining or drum or disc.
Linings worn / Uneven wear ............
Drums / Disc - scored / Uneven wear
*
*
*
*
Adjust properly
Clean and refit
Replace linings
Rectify or Replace drums / disc
VIII. VEHICLE WOBBLES
1)
2)
3)
4)
5)
Wheel rim runout ..............................
Loose / Broken spokes ....................
Tyres not fitted correctly ..................
Wheels misaligned ...........................
Under inflated tyres ..........................
* Rectify
* Tighten / Replace spokes
* Refit tyres correctly
* Ensure proper alignment
Inflate to correct pressure
IX. ELECTRICALS
Bulbs do not glow
1) Loose / improper connection ...........
* Check and correct
* Contact Authorised Dealer / Service Point
Trouble Shooting
76
CAUSES
REMEDIES
2) Bulb fused ........................................
3) Fuse blown .......................................
Horn not working
1) Loose connections ...........................
2) Fuse blown .......................................
Trafficators not working
1) Loose / improper connections .........
2) Bulb fused ........................................
3) Fuse blown .......................................
Brake light remains on
(1) Switch link not adjusted properly ....
(2) Switch sticky .....................................
* Replace bulb
Check and Replace fuse
* Check and correct
Check and Replace fuse
Check and correct
Replace bulb
Check and Replace fuse
* Adjust connecting links properly
* Replace switch
X. ELECTRONIC FUEL INJECTION (EFI)
Malfunctioning Indicator Lamp (MIL) glowing continuously
(1) Sensor Coupler Loose Connection .
* Check for any EFI sensor coupler loose connection and correct them
(2) Any EFI Sensor Failure ......................
* Check & replace the same
* Contact Authorised Dealer / Service Point
Warranty
77
Royal Enfield Motor Cycles are manufactured by following best Quality practices in respect of the material and
workmanship.
Royal Enfield (RE) warrants Classic 500 EFI Motor Cycle to be free from manufacturing and material defect under
normal use subject to following conditions.
1.
RE will replace or repair defective part / parts at their Authorised Dealer / Service Point, free of charge within a
period of 12 months from the date of sale (date of Installation) or 10,000 kms whichever occurs earlier.
2.
The warranty is applicable only to first registered owner.
3.
The warranty shall be applicable only if all the free services are availed at the respective period / kilometer range
as per the schedule given in the owner’s manual from RE Authorised Dealer / Service Point.
4.
During the warranty period, RE’s obligations shall be limited to repairing / replacing free of charge such part or
parts of the vehicle, which on examination to have manufacturing defect. Such defective part / parts which have
been replaced becomes property of RE.
5.
Cost of oil, oil filter, fuel and other consumables are chargeable to the customer.
6.
Claims on proprietary items like tyres, tubes, spark plug, battery etc. should be taken up with respective
manufacturer or their authorised agents in the area directly by customer. RE shall not be liable in any manner
to replace them though their Dealers will provide assistance in preferring such claims on their manufacturer.
7.
Warranty shall not apply to:
(a) Normal ageing, detoriation or rusting of plated parts paints coat, rubber parts, soft items, glass items,
plastic parts etc.
Warranty
78
(b) Components like fuel filter, oil filter paper element, control cables, brake shoes / brake pads, clutch plates,
drive chain & sprocket kit, which are subjected to normal wear and tear.
(c)
(d)
(e)
(f)
(g)
(h)
Damages due to use of lubricant / oil / grease etc., other than specified by RE.
Damages due to use of non-genuine parts.
Damages due to lack of proper maintenance of the vehicle.
Damages due to incorrect driving or riding habits.
Parts damaged due to accidents, collision, abuse etc.
Irregularities not recognized as affecting the quality or function of the vehicle such as slight vibration, oil
leakage, discoloration of exhaust bent pipe / silencer / soft or hard shock absorber etc.
(i) Defects arising from fitment of unauthorised / additional Electrical loads.
(j) Vehicle serviced / repaired at unauthorised service points.
(k) Vehicle used for competition / racing.
(l) Electrical component like bulbs, fuses etc. & Electronic components failure due to repairs by arc welding.
(m) Normal maintenance operations like adjustment of brakes, cleaning fuel system, engine tune up and
other such adjustments
8. RE reserves the right to finally decide on all warranty claims
9. RE reserves the right to make changes in Design of the vehicle without any obligation to install these changes
on previously supplied vehicles.
Note: Scratches or marks cannot be removed, No warranty for DESERT STORM Colour.
Emission Warranty
79
In compliance with the provisions of Rule 115(2) of the Central Motor Vehicle Rules, 1989, Royal Enfield certifies
that the following warranty is applicable to those components liable to affect the emission of the gaseous pollutants
in its range of motorcycles, in normal use to which it may be subjected to.
This emission warranty comes into force from 01st July 2001 and is valid for a period of 30,000 Kms. or 36
months, whichever occurs earlier, from the date of sale to the first customer and is in addition to and parallel to
the warranty policy, conditions and obligations laid down in the Owner’s Manual.
Royal Enfield further warranty that if on examination by its Authorised Dealer / Service Point, the motorcycle fail
to meet the specified emission standards, then the Authorised Dealer / Service Point shall take necessary corrective
measures and shall at its sole discretion, repair or replace free of charge such components of the emission
control system to meet the required emission standards.
The method/s of examination to determine the warranty conditions of the emission warranty related components
will be at the sole discretion of Royal Enfield and / or our Authorised Dealer / Service Point and results of such
examination will be final and binding. If on examination the warranty conditions of the part/s is/are not established,
Royal enfield will have the right to charge all, or part of the cost of such examination to the customer in addition
to the cost of the components.
In case of acceptance of the component/s under Emission warranty, Royal Enfield will replace free of charge, the
component/s as required. However, the consumables like fuel, lubricants, solvents, etc shall be chargeable to the
customer as per actual.
In case any of the components covered under emission warranty or the associated parts, are not independently
replaceable. Royal Enfield will have the sole discretion to replace either the entire assembly or parts of the
assembly, through suitable repairs.
Emission Warranty
80
Royal Enfield reserves the right to carry out necessary consequential repairs to the motorcycle or replace any
part, in addition to the repair or replacement of the components covered under emission warranty, to establish
compliance to in-use emission standards. Such repairs / replacements will be chargeable to the customer.
All parts removed for replacement under warranty will become the property of Royal Enfield.
Royal Enfield will not be responsible for the cost of transportation of the motorcycle to the nearest Authorised
Dealer / Service Point OR for any loss due to non availability of the motorcycle during the period of examination
and repairs by Royal Enfield and / or their Authorised Dealer / Service Point.
Royal Enfield will not be responsible for any penalties that may be charged by statuatory authorities on account
of failure to comply with the in-use emission standards.
That cost/s incurred to check emission of the motorcycle will have to be borne by the customer.
Emission warranty will be applicable irrespective of the change of ownership of the vehicle provided all the
conditions as laid down in this document are met from the date of original sale of the motorcycle.
THE WARRANTY SHALL APPLY IF THE CUSTOMER
Observes all the important instructions and any other precautions listed in the owner’s manual.
Under all circumstances uses lubricants and fuel as recommended by Royal Enfield.
Regularly obtains and carries out maintenance in accordance with Royal Enfield guidelines and enters the
details in the Log book.
Immediately approaches the nearest Authorised Dealer / Service Point upon discovery of failure to comply
with the IN-USE emission standard inspite of having maintained and used the vehicle in accordance with the
instructions in the owner’s manual and having carried out such repairs and adjustments as may be required
with a view to establish such compliance.
Emission Warranty
81
Produce the ‘Pollution Under Control’ certificate valid for the period immediately preceding the test during
which the failure is discovered, the test having been carried out either for obtaining a new certificate or
pursuant upon being directed by an officer as referred to in sub rule (2) of rule 116 of the Central Motor
Vehicles Rules (CMVR).
Produce the Owner’s Manual and Log book for verification details.
Produce receipts covering maintenance of the motorcycle is specified in the owner’s manual from the date of
original purchase of the vehicle.
Produce valid certificate of Insurance and R.T.O. Registration Certificate (RC Book).
THE EMISSION WARRANTY SHALL NOT APPLY IF
A valid “Pollution under control” certificate is not produced.
The motorcycle is not serviced by Authorised Dealer / Service Point as per the service schedule described in
the maintenance chart.
The motorcycle has been subjected to abnormal use, abuse, neglect and improper maintenance or has met
with an accident.
Replacement parts not specified and approved by Royal Enfield have been used.
The motorcycle, or parts thereof, has been altered, tampered with or modified or replaced in an unauthorised
manner.
The odometer is not functioning or the odometer and / or its reading has been changed / tampered with, so
that the actual distance covered cannot be readily determined.
The motorcycle has been used for competitions, races, and rallies or for the purpose of establishing records.
Emission Warranty
82
On examination by Royal Enfield or its Authorised Dealer / Service Point, if the motorcycle shows that any of
the conditions stipulated in the Owner’s manual with regard to use and maintenance have been violated.
The motorcycle has been run on adulterated / leaded fuel or lubricant other than those specified by Royal
Enfield in the Owner’s manual or any other document given to the customer at the time of sale of the motorcycle.
The emission related components are tampered with.
All service and parts related bills and vouchers incurred during the tenure of the emission warranty is not produced.
All maintenance activities carried out on the vehicle during the tenure of the emission warranty is not entered
in the log book.
TIPS TO BE ON THE RIGHT SIDE OF LAW
Always get your vehicle checked to meet the emission regulations through and authorised emission checking centre.
Always carry a valid ‘Pollution Under Control’ certificate with you at all times during the validity of the emission
warranty (30,000 Kms / 3 years from the date of first sale)
TIPS TO REDUCE POLLUTION
1.
2.
3.
4.
5.
Ensure that the periodical maintenance is carried out as stipulated in the owner’s manual through a Royal
Enfield Authorised Dealer / Service Point.
Use only Unleaded petrol (> 91 octane) from reputed fuel pumps.
Ensure the fuel used is not adulterated.
Use correct spark plug as recommended in the owner’s manual.
Use lubricants as per recommendations given on grade / brand in the owner’s manual.
All India Road Signs
MANDATORY SIGNS
INFORMATION SIGNS
83
CAUTIONARY SIGNS
Free Service Coupons
84
It is our endeavour to provide excellent service to your Royal Enfield Motor Cycle at all times. Towards this we
provide four free services at specific Intervals.
Please avail these services at the specified time, in any of the Royal Enfield Authorised Dealer / Service Point
nearest to you and as a token of satisfactory service, kindly return the free service coupon duly filled in and
signed, to the service outlet.
Availing the free services in the specified time is a prerequisite to warranty consideration.
The cost of fuel, oil, oil filter element, grease etc. used for free service is chargeable to the customer.
1st Free Service
1ST
FREE
SERVICE
500 Kms
or
45+8 days
whichever is
earlier from the
date of sale
Enter the Details
in Free Service
Record
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
500 KMS OR 45+8 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Sold by (Dealer’s Name & Address)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
Date :
85
1st Free Service Activities
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ....................................................... Check level & top-up
Battery terminals ............................................. Clean and apply petroleum jelly
Drive chain free play ........................................ Check, clean, lubricate & adjust
Rear brake pedal pivot..................................... Lubricate
Rear brake....................................................... Adjust
Wheel rim front & rear ...................................... Check spokes tightness
Front brake .................................................... Check & top up brake fluid level
Front fork oil leak ............................................. Check for leak
Air filter element ............................................... Clean
Spark plugs (2 Nos)......................................... Check, clean & adjust gap
H.T. Leads ....................................................... Inspect for cracks
Fuel pump ........................................................ Check mounting screws
Fuel hose ......................................................... Inspect for cracks
Rubber hose, Air filter to throttle body.............. Inspect for cracks
Accelerator cable ............................................ Adjust play
Clutch cable ..................................................... Adjust play
Engine oil sump strainer .................................. Clean
Engine oil ........................................................ Replace
Engine oil filter paper element ......................... Replace
Hand levers & kick starter pivot........................ Lubricate
86
CUSTOMER COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp & Signature
2nd Free Service
2ND
FREE
SERVICE
3000 Kms
or
90+15 days
whichever is
earlier from the
date of sale
Enter the Details
in Free Service
Record
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
3000 KMS OR 90+15 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Sold by (Dealer’s Name & Address)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
Date :
87
2nd Free Service Activities
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ...................................................... Check level & top-up
Battery terminals ............................................ Clean and apply petroleum jelly
Drive chain free play ....................................... Check, clean, lubricate & adjust
Rear brake pedal pivot .................................... Lubricate
Rear brake ...................................................... Adjust
Wheel rim front & rear ..................................... Check spokes tightness
Front brake ...................................................... Check & top up brake fluid level
Front fork oil leak............................................. Check for leak
Air filter element ............................................... Clean
Spark plugs (2 Nos) ........................................ Check, clean & adjust gap
H.T. Leads ...................................................... Inspect for cracks
Fuel pump......................................................... Check
Fuel hose ........................................................ Inspect for cracks
Rubber hose, Air filter to throttle body.............. Inspect for cracks
Accelerator....................................................... Check & adjust play
Clutch cable .................................................... Adjust play
Steering free play ............................................ Check & Adjust
Engine oil ........................................................ Check level & top-up
Hand levers & kick starter pivot....................... Lubricate
Oil filter element, oil strainer & magnetic drain plug.. Clean
88
CUSTOMER COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp & Signature
3rd Free Service
3RD
FREE
SERVICE
6000 Kms
or
180+15 days
whichever is
earlier from the
date of sale
Enter the Details
in Free Service
Record
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
6000 KMS OR 180+15 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Sold by (Dealer’s Name & Address)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
Date :
89
3rd Free Service Activities
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ...................................................... Check level & top-up
Battery terminals ............................................. Clean and apply petroleum jelly
Drive chain free play ....................................... Check, clean, lubricate & adjust
Rear brake pedal pivot .................................... Lubricate
Rear brake....................................................... Cam clean, lubricate & Adjust play
Swing Arm bush & spacer................................ Lubricate
Wheel rim front & rear .................................... Check spokes tightness
Front brake ...................................................... Check & top up brake fluid level
Tyres front & rear ............................................ Check wear and tread depth
Air filter element ............................................... Clean
Spark plugs (2 Nos)......................................... Check, clean & adjust gap
H.T. Leads ...................................................... Inspect for cracks
Fuel pump/Fuel hose ....................................... Check / Inspect for cracks
Rubber hose, Air filter to throttle body ............. Inspect for cracks
Accelerator cable ............................................ Check & adjust play
Clutch cable .................................................... Adjust play
Engine oil sump strainer .................................. Clean
Engine oil & oil filter paper element................... Replace
Throttle body / Injector..................................... Clean by carbo spray*
Hand levers & kick starter pivot....................... Lubricate
PAV System .................................................... Check & Clean
Steering System .............................................. Check, Lub. steering balls & adj. play
*Recommended - ITW Chemin or Wurth
90
CUSTOMER COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp & Signature
4th Free Service
4TH
FREE
SERVICE
9000 Kms
or
270+15 days
whichever is
earlier from the
date of sale
Enter the Details
in Free Service
Record
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
9000 KMS OR 270+15 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Sold by (Dealer’s Name & Address)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
Date :
91
4th Free Service Activities
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ....................................................... Check level & top-up
Battery terminals ............................................ Clean and apply petroleum jelly
Drive chain free play ....................................... Check, clean, lubricate & adjust
Rear brake pedal pivot .................................... Lubricate
Rear brake / cam............................................. Lubricate & Adjust
Wheel rim front & rear ...................................... Check spokes tightness
Front brake ...................................................... Check & top up brake fluid level
Front fork oil leak............................................. Check for leak & replace oil
Air filter element ............................................... Clean
Spark plugs (2 Nos) ........................................ Check, clean & adjust gap
H.T. Leads ...................................................... Inspect for cracks
Fuel pump ....................................................... Check
Fuel hose ........................................................ Inspect for cracks
Rubber hose, Air filter to throttle body ............ Inspect for cracks
Accelerator cable............................................. Check & adjust play
Clutch cable .................................................... Adjust play
Engine oil ....................................................... Check & top-up
Hand levers & kick starter pivot....................... Lubricate
Steering System .............................................. Check, Lub. steering balls & adj. play
Tyres................................................................ Check wear and tread depth
92
CUSTOMER COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp & Signature
Paid Service / Maintenance Record
CUSTOMER COPY
93
DEALER / ASP COPY
12,000 + 250 Kms. Service
12,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
15,000 + 250 Kms. Service
15,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Paid Service / Maintenance Record
DEALER / ASP COPY
12,000 + 250 Kms. Service
94
CUSTOMER COPY
12,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
15,000 + 250 Kms. Service
CUSTOMER COPY
15,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Paid Service / Maintenance Record
CUSTOMER COPY
95
DEALER / ASP COPY
18,000 + 250 Kms. Service
18,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
21,000 + 250 Kms. Service
21,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Paid Service / Maintenance Record
DEALER / ASP COPY
18,000 + 250 Kms. Service
96
CUSTOMER COPY
18,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
21,000 + 250 Kms. Service
CUSTOMER COPY
21,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Paid Service / Maintenance Record
CUSTOMER COPY
97
DEALER / ASP COPY
24,000 + 250 Kms. Service
24,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
27,000 + 250 Kms. Service
27,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Paid Service / Maintenance Record
DEALER / ASP COPY
24,000 + 250 Kms. Service
98
CUSTOMER COPY
24,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
27,000 + 250 Kms. Service
CUSTOMER COPY
27,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Paid Service / Maintenance Record
CUSTOMER COPY
99
DEALER / ASP COPY
30,000 + 250 Kms. Service
30,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
33,000 + 250 Kms. Service
33,000 + 250 Kms. Service
Job Card No :................. Date : .........................
Job Card No :................. Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Paid Service / Maintenance Record
DEALER / ASP COPY
30,000 + 250 Kms. Service
100
CUSTOMER COPY
30,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
33,000 + 250 Kms. Service
CUSTOMER COPY
33,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
Log Book
Sl.
No.
Date
Kms.
101
Details
Idling
CO%
Authorised Dealer / Service Point
Stamp &
Job Card No.
Signature
Log Book
Sl.
No.
Date
Kms.
102
Details
Idling
CO%
Authorised Dealer / Service Point
Stamp &
Job Card No.
Signature
Notes
103
Notes
104
Telephone Residence
Bike Regn. No.
Invoice No.
Sales Representative
or
Telephone Office
No
Delivery Note / Advice No.
Yes
E
Have you visited Royal Enfield website?
PRE DELIVERY INSPECTION LIST
Engine No:
H / LF / NW
-
2-3 mm / (STD)
5 Litres
Same
Clean
Fill 2.5 Litres (Capacity is
Replace oil & oil filter / Check Oil level (3 Drain
EO - (Drained 2.75 Litres) - Remove 3
Bolts system Hex 19mm, 8mm X 2nos and
Oil Level)
Drain Bolts to Drain the
Hex 12mm head bolts)
complete Oil
13 Front Tyre Pressure
EP / V / T
H/N
LESS
Tight
Smooth
2 - 3 mm
Smooth
22 PSI
Front :
Defect Defect Defect
#1
#2
#3
Rear :
Remarks
MODEL: BULLET 350 / ELECTRA / CLASSIC 350 / CLASSIC 500 / BULLET 500
Model :
Measure
Tyre Number :
Location:
Battery Make :
Key Number :
Area
Dealer's Name :
Battery Number :
Aggregate
Same
Clean Primary Oil Strainer screen
-
2.7 to 3.0 Kgm
DF
3
Ignition / Side Air Filter Box / Tool Box Lock /
Fuel Tank Lock
EP / T
Engine / Vehicle Number Details
Defect
Code
Colour :
1
4
Fill Petrol
LF
CHASSIS / ENGINE
NUMBER
5
Brake Lever Free Play
D / NC / Weak Battery Voltage 12V-whereas
13.5 V (Max. online voltage)
Cell
6
Caliper Mounting Bolts
Free ( Check Spokes
Looseness & Runout
Battery Charging
7
W / T / LF / N
CONNECT BATTERY /
2
CHECK VOLTAGE
LOCK OPERATION
8
Front Wheel Rotation
ENGINE OIL
PETROL
9
Straight
FRONT WHEEL
M / RB
7.0 to 7.7 Kgm
Front Mudguard Alignment / Cover Tube
Rubbing
14 Clutch Operation
T / SY
Good
LF
10
11 Front Wheel Nut
15 Clutch Lever Free Play
LF
12 Front Tyre Condition (Check Tyre Line Seating) WF
16 Accelerator Operation
Free
Tight
CLUTCH
17 Lever Brackets Tightness
LF
W.r.to Dot Punch
T
WF
No Defects
4.5 to 5.5 Kgm
Straight
No Leak ( Tank, Tap,
Carburetor)
LF
L
20 - 30 mm
NW / F
M
Same Level
21 Lock Nut T- Stem
T / EP
22 Electrical Switch Operation
26 Fuel Tank Alignment
DF
20 - 25 mm
Smooth / Main / Reserve
27 Rear Brake Pedal Free Play
T / EP
Free (Check Spokes
Looseness & Runout)
No Defects
28 Pedal Position w.r.t foot rest
W / T / LF / N
Straight
4.5 Kgm
H / NW
29 Chain Tension
LF
32 PSI
NW / F
30 Rear Wheel Rotation
M
23 Neutral Lamp
31 Anchor Pin Nut
LESS
25 Fuel Leak
32 Rear Mudguard Alignment
24 Fuel Tap Operation
18 Switch Modules Tightness
HANDLE BAR
19 Steering Movement
CONTROLS &
ELECTRICAL SWITCH 20 Handle Bar Positioning
OPERATIONS
FUEL SYSTEM
REAR WHEEL
33 Rear Tyre Pressure
Smooth
Good
H / N / AD
34 Rear Tyre Condition (Check Tyre Line Seating) WF
35 RR Shock Absorber Operation / Adjustment
AESTHETICS
OTHERS
TEST RIDE
STATIC CHECK
(AFTER TEST RIDE)
ANY OTHER
Note **
39 Head Lamp Casing - Paint Related
38 Tool Box LH, Air Filter Box, Battery Cover Paint / Plating Related
37 Fuel Tank - Paint Related
36 Mudguards - Paint / Plating Related
SC / PD / R
SC / PD / R /
SC / PD / R /
DN
SC / PD / R /
DN
SC / PD / R /
DN
No Defects
No Defects
No Defects
No Defects
No Defects (Mudguards /
Fuel Tank / Tool Box
SC / R / PO
No Defects
No Defects (Mudguards /
Fuel Tank / Wheel Rim /
Indicator
Powder Coated Parts (Scratch / Rust /
Chipped OFF)
SC / DU
No Defects
40
42 Buffed components poor Buffing & Scratches
M
41 Plated Parts (Scratch / Rusty)
43 Seat Alignment
No Defects
No Defect / Colour
Availability
Tight (RH, LH Cover /
Engine Foundation /
Accessories / Wheel Nut)
M / LF / SC
LF
Tubular / Blade Fuse
M
-
44 Indicators Alignment (MFR / Amber)
NA
45 Stickers / Knee Pads
47 Owner's Manual & Tool Kit Content
Sharp
Easy Start
46 Nuts, Bolts, Fasteners (Torque)
48 Spare Fuse in Fuse Carrier
AD / SG
Smooth
Straight
ST / N
V
P
49 Starting (Kick Start / Self Start)
51 Pulling
50 Front / Rear Brakes Effectiveness / Feel
52 Vibration
N
N / ST / J / H
Smooth
Nil (Silencer / Accessories
/ Body Parts /
Suspension)
Smooth
No Defects
55 Engine Performance / Gear Shifting /
TPS Setting
ST / NW
No Leak (Oil / Fuel /
Hydraulic / Acid Leakage)
No Defects
56 Any Rattling / Squeaking Noise
L
Smooth
No Smoke
N
57 Easy Start (Hot Condition)
SK / EO
W
58 Leak
N
53 Wobbling
59 Smoke / Oil Droplets in Silencer
54 Front Fork / Drive Chain Noise
60 Cam Noise / Top End Noise
Lens Colour Check
5. Claim transit loss and damage through ‘TRANSIT’ insurance only.
4. Please ensure delivery of the vehicle in brand new condition.
INSTRUCTIONS
Any Abnormal Noise or Engine Open cases during PDI Inform to Plant / Factory
1. Check the vehicle thoroughly for any transit damages or
shortage of parts.
2. Carry out all jobs listed under Pre-delivery Inspection Schedule.
T
Tight
F
Fused
SC
Scratch
P
Pulling
DN
Dent
WF
Wrong
Fitment
H
Hard
J
Jerking
6. Claim Parts replaced for Manufacturing defects only under
warranty.
D
Discharing
3. Thoroughly road - test the vehicle for performance.
LF
Loose
Fitment
NC
Not Charging
W
RB
Rubbing
Wobbling
EO
Excessive Oil
Less
DU
Dull
LESS
PO
Peel Off
ST
R
Rust
Starting
Trouble/Missing
PD
Paint Defect
L
NW
Not
Working
Leak
AD
Adjustment
V
SK
Smoke
Vibration
NA
Not
Available
N
SY
Sticky
Noise
SG
Spongy
M
DF
Different
Misalignment
EP
DLR / CS COPY
Excess Play
Format No : F/14A/CS/02, Mar. 2013
BIKE INSTALLATION CONFIRMATION BY CUSTOMER
Bike Documents explained (Invoice, Insurance, RC / Road Tax Receipt)
Owner’s Manual received
Recommended Lubricants explained
Maintenance Schedule sheet in Owner’s Manual shown and explained
Next Free Service due explained
All Free / Paid Services explained
Warranty Guidelines explained
“Running in period” details shown in the manual explained
Service Station Address given and Location explained
Service Incharge Name & Mobile No given
Bike delivered in neat and clean condition
Tool Kit & First Aid Kit received and explained
YES
NO
We congratulate you on becoming a proud owner of Royal Enfield bike. We request
you to give this feedback after completion of the delivery process.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Registration No.:
Control Switches & Disc Brake System usage explained
Fuse Box location shown and explained
Recommended Tyre Pressure explained
Bike starting & Gear shifting procedure explained
Quantity of Fuel in Fuel Tank informed
Bike orientation & short distance drive provided
Date and Time of Installation
Name of Person who did Installation
Suggestions If Any:
Model:
Chassis No.:
YES
CUSTOMER
SIGNATURE
NO
We thank you and request you to return this filled up form to the person who
did the bike installation for you
KEEP RIDINGP
FORM 22
[See Rules 47(g), 115, 124 (2), 126A and 127 (1), 127 (2)]
INITIAL CERTIFICATE OF COMPLIANCE WITH POLLUTION STANDARDS, SAFETY
STANDARDS OF COMPONENTS AND ROAD WORTHINESS
Certified that the following vehicle complies with the provisions of the Motor Vehicles Act, 1988,
and the rules made there under, including the following mass emission norms:
Brand name of the vehicle
:-
Chassis number
:-
Engine number/motor number
(in case of battery operated vehicles)
:-
Sub-rule No. of rule
:-
Emission norms
:[Bharat Stage-I/II/III/Bharat (Trem) Stage-III etc.]
Date :
Classic 500
115(2)(i), 115(14)(F)
Bharat Stage III
For ROYAL ENFIELD
Quality Assurance
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement