English - Uniteck
Unisolar
20.24 W
UNIPOWER
EN
200.12 DC
IMPORTANT
!
Please imperatively respect the polarities when connecting your inverter with your battery. A
polarity inversion may damage irreversibly your inverter, these damages are not covered by
the warranty.
:
30/04/2014
www.uniteck.fr
CO00090
Dear customers, thank you very much for purchasing one of our Uniteck products. Please read carefully
and thoroughly all the instructions before using the product.
DESCRIPTION
Unipower 200.12 DC is a 24V DC / 12 V DC current inverter. It transforms the 24V continuous current of
your battery in 12V DC stabilized current. It is adapted to supply in 12V most of electric and electronic
devices or lighting systems.
Its maximum continuous power tolerated is 200 watts.
Unipower is cooled down if needed by a fan according to the charge and to its functioning temperature.
INSTALLATION - FIXING

Unipower was conceived for an indoor use.

Use the Unipower in a well-ventilated room, away from the rain, humidity, dust and condensation.

While using, the inverter may get hot, keep it away from all inflammable.

To assure a good air circulation necessary to the inverter cooling, make sure there is a 15cm (6
inches) free space around the product.
.
Front face
Inversion of polarity
fuse
On/Off switch
Functioning light
"12V battery" output connection
!
2/8
Screw fixing
Respect the polarities while
connecting the cables
WWW.UNITECK.FR
Back face
"24V battery" input connection.
!
Respect the polarities while
connecting the cables
Screw fixing
Protection fuse
Connection terminals
Fixing screws
WWW.UNITECK.FR
3/8
INSTALLATION - CONNECTIONS
Before any connection, check that the inverter is OFF.

Connect your 24V battery with the « DC INPUT » back plugs of your inverter, respecting the polarities
(cables not provided) :
Caution : Firmly tighten the tongs/the terminals, otherwise there are risks of : non supply, abnormal
overheating of the cable, and damages of the supply of the inverter or fire.

Connect your 12V battery with the « DC OUTPUT » front terminals of your inverter respecting the
polarities (cables not provided) :

- connect the black cable to the negative born of the battery (-),
- connect the red tong to the positive born of the battery (+).
Caution : Firmly tighten the tongs/the terminals, otherwise there are risks of : non supply, abnormal
overheating of the cable, and damages of the supply of the inverter or fire.

Put the Unipower ON. The LED lights as soon as the device is on.

After using the inverter :
- put the switch on OFF
Caution : The metallic parts may be hot. Avoid to grasp it with the hands or to put it next to
inflammable products.
INTEGRATED PROTECTIONS

The Unipower are equipped with thermal protection and electrical protection against overloads as well
as a low voltage, overvoltage protection and output short-circuit protection.
The inverter lights off :
- when the inner temperature of the inverter is too high
- when the consumption of the connected devices is over the nominal power of the inverter
- when the battery voltage is to low or too high.
- when there is an output short-circuit.
4/8
WWW.UNITECK.FR
TROUBLESHOOTING
Troubleshooting
Unipower does not deliver current
anymore
Causes
Remedies
Overconsumption
Check that the power of the
connected device is compatible
with the power of the inverter
or if possible reduce the
consumption of the connected
devices.
Recharge your battery or
replace it, if it is defective.
Discharged battery
Battery overvoltage
Check that the battery voltage
is compatible with the inverter.
Replace the battery if it is
defective.
Thermal protection : the inner
temperature of the inverter is
above 45°C
Stop the consumer. Let the
inverter cool down and improve
the ventilation.
Bad connection
Control the inverter/battery
connection.
The fuse on front or back face
is melted.
Replace the fuse by another
fuse of the same size.
Output short-circuit
Control the connections of your
devices to supply.
WWW.UNITECK.FR
5/8
WARNING AND PIECES OF ADVICE

Do not expose the product to a temperature higher than 60°C.

Please follow the safety instructions of the manufacturer of the battery. In case of doubt, consult
the reseller or the installer.

The batteries may produce inflammable Gas. Avoid all flames or sparks.

While manipulating the battery, there is a risk of acid runoff, protect yourself.

Never put in short circuit the + and the – of the battery or the cables. Risk of explosion or fire.

Maintenance: check the cables and all the connections at least once a year.

Maintenance: Use a dry rag to clean the inverter. Never clean with water.

All the tasks must be realized in conformity with the applicable rules of the country concerning
electricity.

This device is not provided for being used be people (including children) whose physical, sensory or
mental capacities are reduced or people deprived of experience or knowledge except if they have
enjoyed, by a person responsible of their safety, their surveillance, preliminary instructions
concerning the device use.
PICTOGRAMS
Device in conformity
European directives
IP10
6/8
with
Only protected against a solid
objet over 50 mm
Caution ! Read the user manual before
use
Product is a target of a selective collection. Do
not throw it away in a domestic dustbin.
WWW.UNITECK.FR
TECHNICAL SPECIFICATIONS
Unipower
200-12 DC
SYSTEM
Nominal continous power
Peak power
Technology
Self consumption
Maximum efficiency
Thermal protection
Short circuit protection
Polarity reversal protection
Operating temperature
Humidity rate (non condensing)
Storage temperature
Protection Rating
Nominal continous power
24 V DC / 12 V DC
200W
300W
Inverter
0,03 A
90%
Yes
By interruption
Fuse
-15°C to 45°C
90% max
-30°C to 70°C
IP10
INPUT
Input voltage range
Overvoltage protection
Low battery protection
18V DC -30V DC
Yes
Yes
OUTPUT
Output voltage
Output connection
Overconsumption protection
12,5 V +/-0,5V
Enchufe
Yes
MECHANICAL CHARASTERISTICS
Weight without accessories
Weight with accessories
Weight without accessories
WWW.UNITECK.FR
178 x 89 x 50
0,6 kg
0,6kg
7/8
DECLARATION OF CONFORMITY
The UNITECK company testifies that the 24V/12V inverter described in this manual :
UNIPOWER 200.12 DC is manufactured in conformity with European requirements:
CEM (emission) :
EN 55022-class B
CEM (reception)
EN 55024, EN 61000-4-2, EN 61000-4-3, EN 61000-48
LVD (low tension)
EN 60950-1
Date of CE marking : January 2014.
01/01/2014
Société Uniteck
132 rue Pierre Simon Marquis de Laplace
34500 Béziers
Yoann Fourmond
Chief Executive Officer
WARRANTY
The warranty covers all defects or manufacturing flaws for 1 year from the day of purchase (pieces and
workforce).
The warranty does not cover :
- the normal wear of the pieces (for ex. : cables, etc.).
- the input voltage errors, polarity inversions, incidents due to a bad use, fall, disassembly, or any other
damage due to the transport.
In case of failure, return the device to your supplier, and join :
- a dated proof of purchase (cashier’s receipt, bill…).
- an explanatory note of the failure.
Caution : Our after-sales service does not accept postage due returns.
After the warranty, our after-sales service ensures repairs after acceptance of a quotation.
After-sales service contact :
Uniteck-132 rue Pierre Simon Marquis de Laplace
34500 Béziers -France
E-mail: [email protected]
Fax: +33 (0)4 88 04 72 20
8/8
WWW.UNITECK.FR
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement