Pet Remote Training Collar System User Manual

Pet Remote Training Collar System User Manual
Pet Remote Training Collar System
User Manual
Model: SP 401
This is an effective 1 pet training system. It features an easy-to-use transmitter, 3
audible tones of different frequencies, and 8 different levels of static shock, replaceable
batteries and 200 meters range.
Contents:







1 x Transmitter
1 x 6F22 9V Battery
1 x Antenna (for transmitter)
1 x 1 Adjustable Collar Receivers
1 x 6V Batteries
1 x Test Light (for checking static shock)
1 x User Manual
Quick start Guide
Step 1: Prepare the Remote Transmitter
Screw the antenna into place before using. Do not
operate the remote trainer without a transmitter antenna.
Follow the Positive (+) and Negative (-) signs inside the
transmitter. Insert the 9V 6F22 battery into the transmitter
correctly.
Step 2: Prepare the Collar Receiver
Insert the 6V (4LR44) battery into the receiver collar following the Positive (+) and
Negative (-) signs. The collar will beep when you install the battery into receiver
correctly, and LED indicated light will stay on for 2 second. Collar is in the standby mode
and ready to receive signal, which will consume a small amount of electricity.
Step 3: Match Transmitter with the Collar Receiver
The Transmitter and Receiver are automatically matching.
1
LAVA Electronics Inc. Tel: 1-909-923-8743, Email: [email protected] www.lavasat.com
LAVA Electronics Inc. Copyright 2009-2010, All Rights Reserved
Press 1 Button on the transmitter. The LED indicated light on the transmitter will stay on
for about 2 seconds and then turn off. The Receiver will start static shock and the LED
indicated light will be on.
Press the A Button and the Receiver will beep.
Please always install the transmitter’s battery BEFORE install the receiver’s battery
because it is a wireless training system. The transmitter has to be power on then the
receiver is able to receive the code from transmitter. It might not work if you did not
install the batteries correct.
Step 4: How to Check the Static Shock
1. Use the TEST LIGHT attach on the both side of
Electrodes (Metal).
2. Press Shock Button, the TEST LIGHT will blink or
keeps on.
Step 5: Adjust the collar to fit your pet
To ensure a proper fit, please follow the steps below:
1. Put the collar receivers on your pet.
2. With your dog standing, centre the collar receiver where contact points are
underneath your pet’s neck, touching the skin. If your dog has a long or thick
coat, trim the hair around the contact points to ensure consistent contact.
3. The collar receiver should fit snugly, yet loose enough to allow on finger to fit
between the strap and your dog’s neck. If the strap is too long for your dog, cut
off the excess length.
4. Allow your dog to wear the collar for several minutes and then recheck the fit.
Check the fit again as your dog becomes more comfortable wearing the collar
receiver.
Notice:
We recommend you to use the audio function first before starting the static shock and
always start from the lowest level of static shock.
2
LAVA Electronics Inc. Tel: 1-909-923-8743, Email: [email protected] www.lavasat.com
LAVA Electronics Inc. Copyright 2009-2010, All Rights Reserved
How to use the transmitter and receivers
Button 1- 8 are for 8 different levels static shock. (Decrease in static shock which the 1
Button is the strongest static shock)
Button A - C are for 3 different Audio Tones.
How to change the batteries
It is important to check the battery regularly by monitoring indicated light to ensure the
collar is working properly.
If the Receiver LED indicated light does not light up please replace the battery of
receiver. If the Transmitter indicated light does not light up please replace the battery of
transmitter.
Important:
1. The valid distance of remote control means the straight-line distance between the
transmitter and the receiver without obstacles in between. If there are
interference signals or signal screening around, the actual remote control distance
may vary.
2. The lifetime of the batteries vary according as how often you use the product.
Therefore you should often check the batteries by watching the indicator light on
the receiver and the indicated light on transmitter.
3. This product is for pet training. Good effect can only be achieved after a period of
training.
4. This product is a wireless transmitting device; you MUST NOT use the remote
control system in places like petrol stations or hospitals where mobile phones are
prohibited. Patients using heart pacemaker are forbidden to use this product.
5. The Electrodes have to directly touch your pet’s skin as it is very important to
effective training.
6. This product is only for Pet Training, It is not a regular Pet Collar. Please remove it
from your pet at least 8 hours out of every 24 hours.
Made in China
3
LAVA Electronics Inc. Tel: 1-909-923-8743, Email: [email protected] www.lavasat.com
LAVA Electronics Inc. Copyright 2009-2010, All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement