TM600P
ITALIANO
TM600P
6 zones multifunction
burglar central unit panel
USER`S MANUAL
EMC 89/336 CEE
TM600P - User manual
Contents
Chapter 1
Introduction 3
1.1 Description of central .......................................................................................................3
1.2 Operating features ..........................................................................................................3
1.3 Technical features ..........................................................................................................4
Chapter 2
Installation 5
2.1 Safety warning......... ........................................................................................................5
2.2 Power supply
..........................................................................................................5
2.3 Connections
..........................................................................................................6
2.3.1
Card Sk50 for electronic key SK...................................................................7
2.3.2
Volumetric detectors .....................................................................................8
2.3.3
Contacts .......................................................................................................9
2.3.4
Mobile telephone dialer ..............................................................................10
2.3.5
Burglars ......................................................................................................11
Chapter 3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Programming1
2
Regulation time of outputs .............................................................................................12
Regulation time of inputs ...............................................................................................13
Regulation duration alarm..............................................................................................14
Function GONG and acoustic signalling........................................................................15
CONTINUOUS Function GONG on zone 1 ...................................................................16
Warning of the main power supply ................................................................................17
Selection of the zone for the partial insertion of the system ..........................................18
Variation of the security code.........................................................................................19
Restoration of the value set up in factory ......................................................................20
Chapter 4
Operation 2
1
4.1 Panel description .... ......................................................................................................21
4.2 Insertion of burglar system ............................................................................................22
4.2.1
Total insertion .............................................................................................22
4.2.2
Total garrisoned insertion (without burglars)...............................................22
4.2.3
Partial insertion...........................................................................................23
4.2.4
Partial garrisoned insertion (without burglars) ............................................23
4.3 Not insertion of burglar alarm system ............................................................................24
4.4 Exclusion/Inclusion of the zones...................................................................................25
4.5 Alarm memory
........................................................................................................26
4.6 Exclusion of the zone 24h..............................................................................................27
Chapter 5
Maintenance 2
5.1 Battery
5.2 Cleaning
5.3 Fuses
2
8
........................................................................................................28
........................................................................................................28
........................................................................................................28
Contents
1
Introduction
Kind customer,
Thank you to have acquired our product that, and we are sure, will give you a lot of
satisfactions. We advise you to read this manual carefully, it will be precious both in phase of
installation and of use.
As a customer CIA you can approach to several services, first of all a telephonic technical
attendance on CIA products.
1.1
Description of the central
Panel TM600P is a burglar alarm central with technology at microprocessor to use in the
context of modular series TM; it installs in a container TM3 or TM4 and fed with power
supplier/battery TM15 or TM25, or respective version with auxiliary relè .
Central panel alarm TM600P manages a burglar alarm system of production at 5 zones,
more one zone for the anti sabotage protection; it must used in coupling to magnetic sensors of
perimetrical protection, and/or in coupling to volumetric detectors of presence.
Alarm can be: sonorous / luminous, in coupling to the self powered burglar of outside
SA310; sonorous, in coupling to the burglar piezoelectronic for insides SP31; telephonic, in
coupling to the outside mobile telephone dialer CT81, or in coupling to panel mobile telephone
dialer TM81P or TM82P, to install together with central panel burglar alarm TM600P in a
combined container TM4C.
1.2
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Operating features
6 zones of protection: 3 immediate/delay, 2 immediate, 1 anti sabotage "24h".
Zones singularly excluded.
Time of output programming from 0 to 199 sec.
Time of input programming from 0 to 199 sec.
Alarm duration programming from 0 to 1990 sec.
Personal code of access to the programming.
Predisposition to card SK50 and electronic key SK.
Total or partial insertion by keypad of the central or electronic key SK.
Function "GONG" on all the zones.
Function "CONTINUOUS GONG " on zone 1.
Possibility of exclusion burglar during the taste of the system.
Function " ALARM MEMORY" to indicate the zone that have generated the alarm.
Incorporated speaker of signalling.
LEDs of control: presence net, time of output, alarm and state zone.
Predisposition to the connection of the system of commando PX, SK, KB and SCM
(proximity key electronic keypad and magnetic paper, ).
Buzzer of signalling of the time of output and alarm (excluding).
Fuses of protection on feeding buzzers and feeding services.
Tamper of protection anti/opening of central (excluding).
3
TM600P - User manual
1.3
!
!
!
!
!
!
!
!
!
Technical featuring
Operating voltage:13 Vcc ± 5% (Only feeder series TM)
Absorption in stand-by max:50 mA
Tension in output services:13 Vcc
Current supply in output services max:900mA (with TM15 or TM15R)
1500mA (with TM25 or TM25R)
Maximum current output alarm memory:100 mA
Fuse of protection output burglar:3A rapid type 5x20mm
Fuse of protection output services:1A rapid type 5x20mm
Dimensions:285x120x22mm
®
PROGETTAZIONI E PRODUZIONI ELETTRONICHE
DICHIARAZIONE
DI CONFORMITA’
COSTRUCTOR: HiLTRON S.r.l.
ADRESS: Via Caserta al Bravo, 218 - 80144 - NAPOLI
TRADE MARK:
CODE OF PRODUCT: TM600P
DESCRIPTION OF PRODUCT: PANEL BURGLAR ALARM SYSTEM 6 ZONE
DESCRIBED PRODUCT OVER TURN OUT CONFIRMING TO REQUIREMENTS PRESCRIBED
IN THE FOLLOWING NORMS :
APPLIED NORM
TITLE
EN50130-4
NORM OF PRODUCT FOR IMMUNITY
EN50081-1
GENERIC NORM OF EMISSION
Class of the generic norm: domestic, commercial and light manufacturer.
EN50082-1
GENERIC NORM OF IMMUNITY
Class of the generic norm: domestic, commercial and light manufacturer.
THE CONFIRMATION HAS BEEN ESTIMATED ON BASE OF TESTES EXECUTED ON SAMPLES
AND WITH PREPARATION THAT IS SIMILAR TO THE CONFIGURATION WORK PREVIEWED
FOR ITS USE, SO THE PRODUCTS SATISFY REQUIREMENT OF THE DIRECTIVE 89/336/CEE
AND, WHERE APPLICABLE, OF THE DIRECTIVE 73/23 CEE.
DATE
2nd Jenuary 2002
4
L’AMMINISTRATORE DELEGATO
Introduction
2
Installation
2.1
Safety warning
Do not install central in places exposed to extreme temperatures or the inclemencies.
For a solid and reliable implantation, it is indispensable to make sure that the surface of the
wall is level.
Fix central to an height that allows an easy access to the frontal panel.
Central is protected against tamping, but installation in a protect local and eventually in the
zone of cover of a volumetric detector is one additional protection.
Carry out connections to the terminal after the assembly of the equipment.
Execute the connections according norm CEI 79-3 “particular Norm for the anti/effraction,
anti intrusion, burglar alarm and anti agression system”.
Central panel burglar alarm TM600P must be installed on the superior part of a container
TM3 or TM4 with two screws in the confection. It is also possible to install central panel
burglar alarm in coupling to a panel mobile telephone dialer. In that way it is necessary to
use container TM4C.
!
!
!
!
!
!
!
2.2
Power supply
It is important to know that power supply of all the system is furnished exclusively from the
present battery 12V7Ah to the inside of the central; it is constantly held in loads by power
supplier/battery, which will be connected to the main power supply 230V~ .
WARNING!
The main voltage 230V~ has to be connected to the power supplier/battery by two 1,5
mmq wires double isolation coming from a sectioning switch (i.e. a magneto thermic
switch) used only for burglar central unit. Inside of central positioning the two wires in a
way sufficiently tidy, locking them by wrappers in the containers TM3, TM4 e TM4C.
Sectioning switch
Voltage
230V~
50Hz
5
TM600P - User manual
At completed system, connect to the battery the two connectors fortified of cable head
faston type from the local power supply. Attention (Red = [+] positive battery / Black = [-]
negative battery), to avoid to damage gravely connection devices.
ATTENTION !
The 12V7Ah battery must be always connected. Ensure periodically of its efficient charge state
measuring the tension at its heads with a volt meter, after disconnecting the main power supply from
the local power source by the appropriate sectioning switch. Also in case of charging of the load
battery it is necessary to disconnect the main power supply from the local power source to avoid
that entire system burden on it .
Do not connect on 13vcc services power supply output of the central (clamps[4] and [5] "+12V") a
load beyond the available maximum current (see pag.4).
After connecting battery of central and of burglar, it will be able to proceed to the ignition of
the sectioning switch that connects the main power supply on the clamps of the local power
source.
For reasons of security and respect of the norms in vigor we advise to carry out and to
verify the connection to an efficient earth system of devices that had need, included the
metallic container of the central.
LED NET present on panel of the central signal the effective presence of the mains
voltage.
2.3
Connections
1
1-2
2
3
4
5
6
7
8
9
10 11 12 13 14
15 16 17 18 19 20
Output tension 13Vcc fixed self powered burglar. Such tension falls in alarm
condition.
2-3
Output tension 13Vcc in alarm condition for burglar.
4-5
Output tension 13Vcc fixed of service (volumetric detectors, mobile telephone
dialer etc.). BE CAREFULLY: available maximum current: see pag.4
6
Output tension 13Vcc inserted central for activation mobile telephone dialer.
7
Output tension 13Vcc 100mA in condition of " ALARM MEMORY" with inserted
central
8-9
Output tension 13Vcc for LEDs of commando systems SK50, PX100, KB.
[8] = LED green, [9] = LED red
10 - 11
Terminals for insertion/not insertion of the system by eventual systems of
commando Sk50, PX100, KB used in MONOSTABLE modality (an impulse of
closing of terminals insert, another successive not insert).
12 - 13
Line NC* of protection zone anti sabotage “24h” immediate
14 - 15
Line NC* of immediate or delayed zone1 .
Line NC* of immediate or delayed zone2 .
14 - 16
14 - 17
Line NC*of immediate or delayed zone3 .
14 - 18
Line NC*of immediate or delayed zone4 .
14 - 19
Line NC* of immediate zone 5 .
20
Common(usable in alternative to [14].
*
If the alarm zone are not used, clips must be short circuit.
6
Installation
2.3.1
Card SK50 electronic key SK
SK50
TM600P
SKI/NL
4S
A
B
C
D
On
Off
Lightning
LED Red
LED green
Zone/s opened/s
Zones closed
Alarm memory
System not inserted
System inserted
Time of output in course
7
TM600P - User manual
2.3.2
Volumetric detectors
In series to
the line 24h
2B4
PG12
NOTE: the connection to the zone brought back is pure indicative
8
Installation
2.3.3
Contacts
Function impulses count
activated
(par. 3.9 a pag.20)
In series to the
line 24h
4S
C800
2S
Long threads
C451
Contact NC for shutters
with protection 24h
Short threads
4S
Short threads
C401/P
Contact NC
with protection 24h
C800
2S
Long threads
NOTE: the connection to the zone brought back is pure indicative
9
TM600P - User manual
2.3.4
Mobile telephone dialer
In series to the
line 24h
CT81 / TD81 / TM81P
2B4
Telephone
line
10
Installation
2.3.5
Burglars
In series to the
line24h
4S
4S
SA310 (whole module)
SP31
11
TM600P - User manual
3
Programming
3.1
Regulation time of outputs
After inserting the system, the time of output allows to abandon protected ambients
passing, for example, in the zone of cover of a detector, without to provoke alarms. The time of
escape starts after the insertion of the system and has a programming duration this phase.
During last three seconds of the time of escape an acoustic signalling will be had, than at
the end of the time of escape it will be totally active the protection of ambients.
At central switched off:
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key
#
. LED
will begin to flash fast.
!
Press key
4
. LED
will be switched off fixed.
!
Insert the time of output expressed in seconds: from 000 to 199.
!
Press key
#
.
1
2
3
4
.
to exit from the programming.
NOTE: In whichever condition, in error case it is possible press key
programming.
12
to exit from the
Programming
3.2
Regulation time of input
At inserted system, the time of input allows to approach to protected ambients passing,
for example, in the zone of cover of a detector delaying the activation of alarms. The time of
input starts after the opening of one of zone 1, 2 or 3 and has one programming duration
independently for every zones.
At central switched off:
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key
!
Press:
6
6
6
key
key
key
1
2
3
#
#
.
. LED
1
2
3
4
.
will begin to flash fast.
to program the time of input on zone 1;
to program the time of input on zone 2;
to program the time of input on zone 3.
!
LED
will be ignited fixed.
!
Insert the time of input wished on the pre choice zone expressed in seconds: from 000 to
199.
!
Press key
to exit from the programming.
NOTE: In whichever condition, in error case it is possible press key
programming.
to exit from the
13
TM600P - User manual
3.3
Regulation alarm duration
At inserted system, the opening of an immediate zone or the opening of a delayed zone
(followed from the programmed time of input) will active an alarm cycle, during which inner
buzzers will be activated, self powered burglars and eventual mobile telephone dialer
connected. The alarm duration is programmed in this phase.
At central switched off:
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key
#
. LED
will begin to flash fast.
!
Press key
5
. LED
will be ignited fixed.
!
Insert the time of alarm duration wished expressed in tens of seconds: da 000 a 199.For
example, considering equal unit to 10 seconds:
fingering 015 for 150 seconds;
fingering 115 for 1150 seconds.
fingering 000 alarm will last for the inflation time of the zone.
!
Press key
#
.
1
2
3
4
.
to exit from the programming.
NOTE: In whichever condition, in error case it is possible press key
programming.
to exit from the
BE CAREFULLY: For norm CEI 79-2 duration of alarm must be comprised between 3 and10
minutes.
14
Programming
3.4
Function GONG and acoustic signalling
Function GONG allows to control of opening of every zone by a beep: it is possible to
active this function independetly on every zone.
In this phase it is also possible qualify or not qualify all the acoustic signalling of the
speaker inside to the central TM600P: time of input, output, alarm and function GONG.
At central switched off:
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key
#
. LED
will begin to flash fast.
!
Press key
8
. LED
will be ignited fixed.
!
Press the number of the zone/s (from 1 to 5 ) on which activate that function. LEDs from
“Z1” to “Z5” ignited will indicate the zones with qualified function GONG. Every pressure on
key allows to pass from the phase of qualification to that of not qualification and vice versa.
!
Pressing 6 it qualify or not qualify all the acoustic signalling (time of input, of output,
alarm, function GONG): qualification is marked from LED “24h” switched on.
!
Press twice key
#
.
1
2
3
4
.
to exit from the programming.
NOTE: In whichever condition, in error case it is possible press key
programming.
to exit from the
15
TM600P - User manual
3.5
Function GONG CONTINUOUS on zone 1
Zone 1 usually used for the protection of the input door.
Such function allows to signal the eventual forgetfulness of the opened door by the
continuous repetition of an acoustic signalling at regular intervals; the duration of that interval is
programmed like following.
At central switched off:
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key
!
Press key
!
Insert the time of alarm duration wished expressed in tens of seconds: da 000 a 199.For
example, considering equal unit to 10 seconds:
fingering 015 for 150 seconds;
fingering 115 for 1150 seconds.
fingering 000 alarm will last for the inflation time of the zone.
!
Press key
#
#
6
.
. LED
.LED
1
2
3
4
.
will begin to flash fast.
will be ignited fixed.
to exit from the programming.
NOTE: In whichever condition, in error case it is possible press key
programming.
16
to exit from the
Programming
3.6
Warning of absence main power supply
In case of absence of the main power supply an acoustic signalling will be emitted from the
buzzer of the panel after the programmed time of wait as following procedure.
To exclude the function program 000 like of delay.
At central switched off:
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key
#
. LED
will begin to flash fast.
!
Press key
7
. LED
will be ignited fixed.
!
Insert the time of alarm duration wished expressed in tens of seconds: da 000 a 199.For
example, considering equal unit to 10 seconds:
fingering 015 for 150 seconds;
fingering 115 for 1150 seconds.
!
Press key
#
.
1
2
3
4
.
.
NOTE: In whichever condition, in error case it is possible press key
programming.
to exit from the
17
TM600P - User manual
3.7
Selection of the zone for the partial insertion
The partial insertion allows to active burglar alarm system including only pre choice zones;
such function is useful if it wants, for example, insert burglar alarm system nightly hours: for
example, it will be able to not qualify volumetric detectors and leave qualified perimetrical
protections.
This procedure allows to select the security zones that will be qualified in the partial
insertion of the system.
At central switched off:
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key
#
. LED
will begin to flash fast.
!
Press key
9
. LED
will be ignited fixed.
!
Press the number of the zone/s to include/exclude in the partial insertion. The ignited
LEDs will indicate the zones with qualified function. Each pressure on key allows to pass
from the phase of qualification to that one of not qualification and vice versa.
!
Press twice key
#
.
1
2
3
4
.
to exit from the programming.
NOTE: In whichever condition, in error case it is possible press key
programming.
18
to exit from the
Programming
3.8
Variation of security code
The programmed code in factory 1 2 3 4 it can be changed like final user want; to such
aim follow the procedure described in this phase.
At central switched off:
!
Press key
.
!
Insert security code . The one adopted in factory is :
!
Press key
!
Press key
!
Insert two consecutive times security code of 4 figures wished.
!
LED
!
Press key
#
#
0
. LED
. LED
1
2
3
4
.
will begin to flash fast.
will be ignited fixed.
it will switched off.
to exit from the programming.
NOTE: In whichever condition, in error case it is possible press key
programming.
to exit from the
19
TM600P - User manual
3.9
Restoration of the values sets up in factory
To restore the value set up in factory follow this procedure.
!
Press key
!
Insert security code . The one adopted in factory is :
!
Press key # . LED
!
Press key "RESET" put in the inside of the panel until hearing sonorous signal emitted
from the central.
!
Press key
!
!
!
!
!
!
!
!
!
!
!
#
.
1
2
3
4
.
will begin to flash fast.
. It will be restored following values:
Time of input on zona 1
Time of input on zona 2
Time of input on zona 3
Time of output
Alarm duration
Interval duration warning opened zona 1
Interval duration warning lack net
Qualified zones in the partial insertion
Gong
Acoustic signalling
Including zones
010 (10 sec.)
000 (0 sec.)
000 (0 sec.)
020 (20 sec.)
030 (300 sec. = 5 min.)
030 (300 sec. = 5 min)
1
2
3
4
Zone 1, 3 e 4
Qualified on zone 1
Qualified
All
NOTE: In whichever condition, in error case it is possible press key
programming.
20
to exit from the
Programming
4
Operating
4.1
Panel description
9
LED ON/OFF (Yellow)
On
Not inserted system
Not inserted system- excluding
Flashing slow
zones
Flashing fast
Time of output in course
LED NET
On
Flashing slow
Flashing fast
LED ZONA 1
On
OFF
LED ZONA 2
On
OFF
LED ZONA 3
On
OFF
LED ZONA 4
On
OFF
Tension of net present
Tension of net absent
Programming in course
Opened zone
Closed zone
LED ZONA 5
On
OFF
Opened zone
Closed zone
LED ZONA 24h
On
OFF
Opened zone
Closed zone
9
TAMPER ANTI OPENING CENTRAL
Connected in series to line 24h.
KEY RESET
For the restoration of the values set up in factory.
Opened zone
Closed zone
Opened zone
Closed zone
Opened zone
Closed zone
KEYPAD
For the management of the central.
SPEAKER
Signal several phases of operating and of
programming.
21
TM600P - User manual
4.2
Insertion of burglar alarm system
By numerical key present on the front of the panel it is possible to insert burglar alarm
system in following ways:
! Total insertion
! Total garrisoned insertion (without buzzers).
! Partial insertion
! Partial garrisoned insertion (without buzzers).
Total or partial insertion is also possible by electronic key or other device (key of proximity,
magnetic paper, electronic keypad).
4.2.1
Total insertion
It previews the activation of all security zones, except those excluded (par. 4.3). To insert
totally burglar alarm system:
!
Press security code.
!
Press key
1
.
It will be available the time of output to abandon all protected ambients. Last three seconds
available will be accompany from an acoustic signalling if qualified.
Or:
!
Insert electronic key in key reader.
!
LED green start to flash.
!
Extract key before that the lightning is finished.
4.2.2
Total insertion garrisoned (without buzzers)
It previews the activation of all security zones, except those excluded (par. 4.3), and the
inhibition of burglars output, leaving the singular acoustic signaler of the central if qualified.
To insert burglar alarm system in total garrisoned way:
!
Press key
!
Press security code.
!
Press key
#
1
.
.
It will be available the time of output to abandon all protected ambients. Last three seconds
available will be accompany from an acoustic signalling .
22
Operating
4.2.3
Partial insertion
It Previews the activation the only qualified security zones in partial insertion (par. 3.7),
except those excluded(par. 4.3). To insert burglar alarm system in garrisoned way:
!
Press security code.
!
Press key 2 .
It will be available the time of output to abandon protected ambients eventually qualified in
the partial insertion. Last three seconds available will be accompany from an acoustic
signalling.
Or:
!
Insert electronic key in key reader.
!
LED green start to flash.
!
Extract key after that the lightning is finished.
4.2.4
Partial garrisoned insertion (without buzzers)
It Previews the activation the only qualified security zones in partial insertion (par. 3.7),
except those excluded (par. 4.3), and the inhibition of buzzers output, leaving the singular
acoustic signaler
incorporated in the central. To insert burglar alarm system in partial
garrisoned way:
!
Press key
!
Press security code.
!
Press key
#
2
.
.
It will be available the time of output to abandon protected ambients eventually qualified in
the partial insertion. Last three seconds available will be accompany from an acoustic
signalling.
23
TM600P - User manual
4.3
Burglar alarm system switched off
During time of output, at inserted system or during the alarm it is possible not insert the
system pressing security code or inserting key in key reader. At still inserted central the slow
flash of the red LED on key reader indicates alarm memory. At not inserted central eventual
alarms are signalled from the fast flash of the LED of zone on central.
24
Operating
4.4
Exclusion/inclusion of the zones
At the moment of the insertion of the system, any it is, it is previewed the possibility to
exclude fastly the zones that are not necessary protect between those qualified from total
insertion, or between that only qualified from the partial insertion. The unqualified zones from
the partial insertion however they will be excluded.
At central switched off, with LED
switched on:
!
Insert security code . The one adopted in factory is :
!
Press key
!
Pressing correspondent number to the zona to exclude. Relative LED switch off.
!
To include again the zone it is sufficient to press again the relative number to the zone.
!
Press twice key
3
1
2
3
4
.
.
.
NOTE: In whichever condition, in error case it is possible press key
programming and repeat completely the cycle.
to exit from the
25
TM600P -User manual
4.5
Alarm memory
At not insertion of the system eventual "LEDs zones" lightning, will indicate the activated
zones during the period of' insertion. This memory is deleted at successive insertion of the
system.
Pressing
the visualization of the alarm memory is deleted, as following to restore it:
At central switched off:
!
Press key :
!
Press key
!
The relative LED at the zones is switched on that have generated the alarm.
!
Press ones key
26
1
4
2
3
4
.
.
.
Operating
4.6
Exclusion of the zone 24 h
During the installation or the maintenance of the system it is possible to temporary esclude
the provoked alarm of the zona 24h: both that of the only buzzer, that happens opening panel
of the central, both that of the buzzer and of the hooters, that it happens anytime opening the
circuit 24h.
To exclude the alarm of the zone 24h:
!
Insert security code . The one adopted in factory is :
1
2
3
4
.
Closing again the line 24h, protection is automatic restored at the successive insertion.
4
27
TM600P - User manual
5
Maintenance
5.1
Battery
We advise to periodically control the charge state of the battery connected in pad to the
power supply of the series TM.
5.2
Cleaning
To the cleaning of the central use exclusively a soft and humid cloth.
Avoid diluting and abrasive sponges absolutely.
5.3
F1
F2
28
Fuses
Output buzzers 3A fast
Output services 1A fast
115ADE-2.02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement