null  null
PanelView Plus
Terminals
400, 600, 700, 1000, 1250 1500
User Manual
Important User Information
Solid state equipment has operational characteristics differing from those of
electromechanical equipment. Safety Guidelines for the Application,
Installation and Maintenance of Solid State Controls (publication SGI-1.1
available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com) describes some important
differences between solid state equipment and hard-wired electromechanical
devices. Because of this difference, and also because of the wide variety of
uses for solid state equipment, all persons responsible for applying this
equipment must satisfy themselves that each intended application of this
equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for
indirect or consequential damages resulting from the use or application of
this equipment.
The examples and diagrams in this manual are included solely for illustrative
purposes. Because of the many variables and requirements associated with
any particular installation, Rockwell Automation, Inc. cannot assume
responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to
use of information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without
written permission of Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware
of safety considerations.
WARNING
IMPORTANT
ATTENTION
Identifies information about practices or circumstances that can cause
an explosion in a hazardous environment, which may lead to personal
injury or death, property damage, or economic loss.
Identifies information that is critical for successful application and
understanding of the product.
Identifies information about practices or circumstances that can lead
to personal injury or death, property damage, or economic loss.
Attentions help you identify a hazard, avoid a hazard, and recognize
the consequence.
SHOCK HAZARD
Labels may be on or inside the equipment, for example, drive or motor,
to alert people that dangerous voltage may be present.
BURN HAZARD
Labels may be on or inside the equipment (for example, drive or motor)
to alert people that surfaces may reach dangerous temperatures.
Allen-Bradley, CompactLogix, ControlLogix, DH+, FlexLogix, Logix, MicroLogix, PanelView Plus, PLC-5, RSLinx, RSLinx
Enterprise, RSLogix, RSView ME, RSView Machine Edition, RSView ME Station, RSView Studio, Rockwell Automation, RSNetWorx
for ControlNet, RSView32, SLC, SLC 5/03, SoftLogix, and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Summary of Changes
The information below summarizes the changes to this manual since
the last revision.
This manual now includes information for both PanelView Plus and
PanelView Plus CE terminals.
• Terminals previously named VersaView CE terminals are now
named PanelView Plus CE terminals.
• Any reference to VersaView CE in text or images is synonymous
with PanelView Plus CE.
• Any reference to PanelView Plus 700 to 1500 terminals also
includes PanelView Plus CE terminals.
Revision bars, as shown in the margin, identify updated information.
Changes for this version of the document include.
3
Topic
Page
Updated parts list for PanelView Plus CE terminals.
9
Added software support for PanelView Plus CE terminals.
11
Updated logic module information for PanelView Plus CE
terminals.
19
Updated catalog number configuration.
22
Updated product components.
22
Added instructions on how to enter Configuration mode on a
PanelView Plus CE terminal.
57
Startup shortcuts for PanelView Plus CE terminals.
92
Information on the Windows CE operating system.
109
Updated information and procedures for replacing the
backlight.
155
The Remote I/O and DH+ connectors for the PanelView Plus
400 and 600 terminals was updated.
174
Information on transferring files and creating an ActiveSync
connection on PanelView Plus CE terminals.
189
Information on upgrading the CE operating system.
202
Updated troubleshooting information for PanelView Plus CE
terminals.
207…221
Publication 2711P-UM001F-EN-P - March 2007
Summary of Changes
4
Publication 2711P-UM001F-EN-P - March 2007
Table of Contents
Preface
Objectives. . . . . . . . . . . . . . . . . .
Intended Audience . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . .
Additional Resources. . . . . . . . . .
Software and Firmware Upgrades
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
..
..
..
..
. 9
. 9
. 9
10
10
Chapter Objectives . . . . . . . . . . . . . . .
Software Support . . . . . . . . . . . . . . . .
PanelView Plus 400 and 600 Terminals
PanelView Plus 700 to 1500 Terminals .
Catalog Number Configuration. . . . . . .
PanelView Plus Product Components. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
11
11
12
17
22
22
Chapter Objectives . . . . . . . . . . . . . . . . . . . .
Hazardous Locations . . . . . . . . . . . . . . . . . . .
Environment and Enclosure. . . . . . . . . . . . . .
Outdoor Installation for High-bright Displays .
Required Tools . . . . . . . . . . . . . . . . . . . . . . .
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutout Dimensions . . . . . . . . . . . . . . . . . . . .
Mount the 400 or 600 Terminal in a Panel . . .
Mount the 700 to 1500 Terminal in a Panel . .
Product Dimensions . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
..
..
..
..
..
..
..
..
..
29
29
32
32
33
34
34
34
37
39
Chapter Objectives . . . . . . . . . . . . . . . . . . . . .
Wiring and Safety Guidelines. . . . . . . . . . . . . .
Remove and Install the Power Terminal Block .
DC Power Connections . . . . . . . . . . . . . . . . . .
AC Power Connections . . . . . . . . . . . . . . . . . .
Reset the Terminals . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
45
45
46
49
52
55
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
..
..
..
..
..
..
..
..
..
57
57
61
62
62
62
63
68
72
74
Chapter 1
Overview
Chapter 2
Installation
Chapter 3
Power Connections
Chapter 4
Configuration Mode
5
Chapter Objectives . . . . . . . . . .
Access Configuration Mode . . . .
Load an Application . . . . . . . . .
Run an Application . . . . . . . . . .
Application Settings. . . . . . . . . .
Terminal Settings . . . . . . . . . . .
Configure Communications . . . .
Configure Network Information .
Configure Diagnostics . . . . . . . .
Manage Files on the Terminal . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Publication 2711P-UM001F-EN-P - March 2007
6
Table of Contents
Modify Display Settings . . . . . . . . . . . . .
Font Linking . . . . . . . . . . . . . . . . . . . . .
Configure Keypad, Keyboard, or Mouse.
Configure the Touch Screen . . . . . . . . .
Configure Print Options. . . . . . . . . . . . .
Configure Startup Options . . . . . . . . . . .
Configure Startup Tests . . . . . . . . . . . . .
View and Clear the System Event Log . .
Display Terminal Information . . . . . . . .
Display RSView ME Station Information .
Modify the Date, Time, or Time Zone . .
Modify Regional Settings . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
77
81
82
84
87
89
95
97
98
100
101
104
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
109
109
110
111
115
117
Chapter Objectives . . . . . . . . . . . . . . . . . . .
Required Tools . . . . . . . . . . . . . . . . . . . . . .
Precautions . . . . . . . . . . . . . . . . . . . . . . . . .
Compatibility of Terminal Components . . . .
Install RAM or Internal CompactFlash. . . . . .
Install or Replace the Logic Module . . . . . . .
Install or Replace a Communication Module.
Replace the Display Module . . . . . . . . . . . .
Replace the Battery . . . . . . . . . . . . . . . . . . .
Replace the Bezel . . . . . . . . . . . . . . . . . . . .
Replace the Backlight . . . . . . . . . . . . . . . . .
Remove the Product ID Label . . . . . . . . . . .
Replace the Keypad Legend Inserts . . . . . . .
Use an External CompactFlash Card. . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
137
137
137
138
141
142
144
148
150
152
155
158
159
161
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
163
163
164
167
168
169
172
Chapter 5
Windows CE .NET Operating
System
Chapter Objectives . . . . . . . . . . . . . .
Windows CE .NET Architecture . . . . .
Windows CE .NET Programs . . . . . .
Windows CE .NET Operating System .
PanelView Plus CE Memory. . . . . . . .
Control Panel Applications . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
Chapter 6
Install and Replace Components
Chapter 7
Terminal Connections
Publication 2711P-UM001F-EN-P - March 2007
Chapter Objectives . . . . . . . .
Wiring and Safety Guidelines.
Logic Controller Cable Charts
Communication Port Isolation
USB Ports . . . . . . . . . . . . . . .
Serial Connections. . . . . . . . .
Ethernet Connections . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Table of Contents
7
DH-485/DH+/Remote I/O Module . . . . . . . . . . . . . . . . . . . 174
ControlNet Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
DeviceNet Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Chapter 8
Upgrade Firmware
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Applications . . . . . . . . . . . . . . . . . . . . . . . . . . .
Create an ActiveSync Connection. . . . . . . . . . . . . . . . . . .
Firmware Upgrade Wizard. . . . . . . . . . . . . . . . . . . . . . . .
Upgrade Firmware with a CompactFlash Card . . . . . . . . .
Upgrade Firmware with a Network (Ethernet) Connection
Upgrade the Operating System (OS) . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
189
189
189
191
192
196
202
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
205
205
206
209
210
211
212
217
218
218
218
219
220
221
222
Chapter 9
Troubleshoot the System
Chapter Objectives . . . . . . . . . . . . . . . .
LED Indicators . . . . . . . . . . . . . . . . . . .
Isolate the Problem . . . . . . . . . . . . . . . .
Startup Information Messages . . . . . . . .
Startup Sequence . . . . . . . . . . . . . . . . .
Startup Error Messages . . . . . . . . . . . . .
Check Terminal Components. . . . . . . . .
Ethernet Connnection . . . . . . . . . . . . . .
Application Does Not Run . . . . . . . . . . .
Configuration Mode Access . . . . . . . . . .
File System Errors . . . . . . . . . . . . . . . . .
Advanced Diagnostics for CE Terminals .
System Identification Errors . . . . . . . . . .
Restart in Safe Mode . . . . . . . . . . . . . . .
Clean the Display Window . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Appendix A - Specifications
Appendix B - Compatible USB Devices
Appendix C - Available Fonts for Terminal Applications
Appendix D - Programmable Key Definitions
Appendix E - Security Considerations
Index
Publication 2711P-UM001F-EN-P - March 2007
8
Table of Contents
Publication 2711P-UM001F-EN-P - March 2007
Preface
Objectives
This preface provides information on these topics.
• Intended audience
• Parts List
• Additional resources
• Software and firmware upgrades
Intended Audience
Use this manual if you are responsible for installing, operating, or
troubleshooting the PanelView Plus or PanelView Plus CE terminals.
No special knowledge is required to understand this manual or
operate the terminal. However, you must understand the functions
and operations of RSView Machine Edition applications that will run
on the terminal. Consult the application designer for this information.
Equipment installers must be familiar with standard panel installation
techniques.
Parts List
The PanelView Plus terminals ship with these items.
• Power terminal block
• RSView Machine Edition runtime software, preloaded
• Mounting levers for 400 and 600 terminals, quantity eight
• Mounting clips for 700 to 1500 terminals, quantity four to eight
• Installation instructions
• Panel cutout template
Additional items ship with the PanelView Plus CE terminals.
• Windows CE .NET operating system preloaded with Terminal
Services and Internet Explorer
• PanelView Plus CE Accessory CD with utilities and software
development kit for C++.
• Microsoft Windows CE license agreement
9
Publication 2711P-UM001F-EN-P - March 2007
10
Preface
Additional Resources
For additional information, refer to these publications, that you can
download from:
http://literature.rockwellautomation.com.
Resource
Description
DeviceNet Communications for PanelView Plus
Terminals User Manual, publication
2711P-UM004
Provides procedures for creating a
DeviceNet application to run on a
PanelView Plus terminal.
ControlNet Communications for PanelView Plus Provides procedures for creating a
Terminals User Manual, publication
ControlNet application to run on a
2711P-UM003
PanelView Plus terminal.
Modbus Applications for PanelView Plus
Terminals User Manual, publication
2711P-UM002
Provides procedures for creating a
Modbus application to run on a
PanelView Plus terminal.
Wiring and Grounding Guidelines for PanelView Provides grounding and wiring
Plus Devices Technical Data, publication
guidelines for PanelView Plus terminals.
2711P-TD001
Software Development Kit for PanelView Plus
CE Terminals User Manual, publication
2711P-UM005
Provides information for programmers
to develop CE applications for
PanelView Plus CE terminals.
You may also want to refer to:
• online help for RSView Studio or RSLinx software.
• documentation for your controller.
Software and Firmware
Upgrades
Publication 2711P-UM001F-EN-P - March 2007
To receive software updates (software serial number required) and
firmware upgrades for your terminal:
• call your local Rockwell Automation sales office or distributor.
• access http://support.rockwellautomation.com.
Chapter
1
Overview
Chapter Objectives
This chapter gives an overview of the PanelView Plus terminals.
• Software support
• PanelView Plus 400 and 600 features
• PanelView Plus 700 to 1500 features
• Catalog number configuration
• Product components
Software Support
RSView Machine Edition runtime software is included with all
PanelView Plus and PanelView Plus CE terminals. This software
provides runtime and terminal configuration software for the terminals
and does not require activation.
You use RSView Studio software on a personal computer to create
applications that run in the terminals. This software is purchased
separately.
The open Windows CE.NET environment of the PanelView Plus CE
terminals provides:
• familiar Windows desktop and user interface.
• terminal server-client support to configured servers
• Internet Explorer web browser.
• software development kit to support custom C++ applications
for Windows CE.NET operating system.
• third-party device support for Windows CE.NET operating
system.
• Windows CE.NET operating system provides the following
programs:
– File viewers for MS Office: Excel, Word, PowerPoint
– PDF file viewer
– WordPad text editor
– WebServer application
– FTP server
– Support for the .NET compact framework
Some of the above software applications are included on the
PanelView Plus CE Accessory CD.
11
Publication 2711P-UM001F-EN-P - March 2007
12
Overview
PanelView Plus 400 and 600
Terminals
The PanelView Plus 400 and 600 terminals offer:
• base-configured units.
• communication modules.
• power supply, ac or dc.
• displays.
The PanelView Plus 400 and 600 terminals are HMI devices that
provide these features:
• PanelView Plus 400 terminals
– Grayscale graphic displays
– Keypad input support
• PanelView Plus 600 terminals
– Color or grayscale graphic displays
– Keypad, touch screen, or keypad and touch screen input
• Base-configured unit
– RS-232 only
– RS-232, Ethernet, and modular communications interface
• Communication modules provide add-on capability to
base-configured units with a modular communications interface
• Power input, ac (85…264V) or dc (18…30V)
• CompactFlash card slot supports Type 1 CompactFlash cards
• USB port for attaching mouse, keyboard, printer, bar code
scanner, and other devices
• Same panel cutouts as the PanelView Standard 550 terminals
Publication 2711P-UM001F-EN-P - March 2007
Overview
13
Base-configured Units
The base-configured unit of the 400 and 600 terminals is available in
two versions.
• Base unit with RS-232 port and one USB port
• Base unit with RS-232 port, 10/100BaseT Ethernet port, one USB
port, and a network interface for a communication module
Base Unit with RS-232 Only
Power Input, ac or dc
CompactFlash Slot
Base-configured Unit with RS-232
and USB Port only
USB Port
RS-232 Port
Base Unit with RS-232, Ethernet Port, and Modular Communications Interface
Power Input, ac or dc
Interface for
Communication Module
CompactFlash Slot
Base-configured Unit with
RS-232, USB, Ethernet Port, and Network
Interface for Communication Module.
USB Port
RS-232 Port
Ethernet Port
Publication 2711P-UM001F-EN-P - March 2007
14
Overview
Communication Modules
You can attach a communication module with a network interface to
the base-configured unit of the PanelView Plus 400 and 600 terminals
to increase your communication capability with these networks:
• DH-485
• DH+
• Remote I/O (single rack)
• Isolated RS-232
• DeviceNet
• ControlNet
The communication module installs easily on the back of the unit.
Communication
Module
Power Options
The base-configured unit of the PanelView Plus 400 and 600 terminals
is available with either ac (85…264V) or dc (18…30V) power input
providing application flexibility.
Publication 2711P-UM001F-EN-P - March 2007
Overview
15
Display and Input Options
PanelView Plus 400 and 600 terminals are available with these display
and operator input options:
• 400 terminals: 3.8 in. grayscale (320 x 240) graphics display with
keypad
• 600 terminals: 5.5 in. color or grayscale (320 x 240) graphics
display with keypad, touch screen, or keypad and touch support
Touch Screen
The PanelView Plus 600 terminals offer an analog resistive touch
screen for touch input.
IMPORTANT
Use a plastic stylus device with a minimum tip radius of 1 mm
(0.040 in.) to prevent damage to the touch screen.
Publication 2711P-UM001F-EN-P - March 2007
16
Overview
Keypad or Keypad and Touch
The keypad versions of the PanelView Plus 400 and 600 terminals are
available with these options:
• 400 terminals: grayscale display with keypad input only
• 600 terminals: color or grayscale displays with either keypad, or
keypad and touch input
600 Grayscale or Color Terminal
with Keypad, or Keypad and Touch Screen
400 Grayscale Terminal
with Keypad
Replaceable
ID Label
Replaceable ID Label
Numeric Keypad
Numeric Keypad
Backspace and Enter Keys
Tab and Shift Keys
Backspace and
Enter Keys
Tab and Shift Keys
Navigation Keys
Navigation Keys
8 Programmable Function Keys
10 Relegendable Programmable Function Keys
Keys
400
600
Description
F1 through F8
F1 through F10
Programmable keys that initiate functions
on terminal display. Replaceable legends
are available for the 600 terminals allowing
for custom function key labels.
Numeric Keypad
0…9, ., -, Backspace, Enter, Left and Right
Tab keys, Shift keys
Navigation Keys
Use the arrow keys for navigation.
Use the Alt+arrow keys to activate home,
end, page up, and page down functions.
Publication 2711P-UM001F-EN-P - March 2007
Overview
PanelView Plus 700 to 1500
Terminals
17
This section gives an overview of the PanelView Plus 700, 1000, 1250,
1500 terminals.
• Modular components
• Base-configured unit
• Communication modules
• Logic module, standard or CE
• Power supply, ac or dc
• Display modules
The PanelView Plus 700 to 1500 terminals are HMI devices that offer
these features:
• Graphic color-display modules with keypad, touch screen, or
keypad and touch screen support
• Analog resistive touch screen
• Ethernet and serial communications
• Modular communication interface for easy add-on capability
• Memory expansion modules for field upgrades to 256 MB RAM
and 512 MB CompactFlash
• Power input, ac (85…264V ac) or dc (18…32V dc)
• CompactFlash card slot supports Type 1 CompactFlash cards
• USB ports provide connections for keyboard, mouse, and printer
• Field replaceable bezels
• Same panel cutouts as the PanelView Standard and PanelView
Enhanced terminals
• Standard or CE logic module
• 650 MHz Celeron processor in PanelView Plus CE terminals
Publication 2711P-UM001F-EN-P - March 2007
18
Overview
Modular Components
The terminals use modular components allowing for flexible
configuration, installation, and upgrades. You can order items as
separate components or factory assembled per your configuration.
Communication Module
Logic Module
Display Module
Base-configured Unit
The base-configured unit of the terminal consists of:
• display module (700, 1000, 1250, 1500) with keypad, touch, or
keypad and touch input.
• logic module.
Power Input,
ac or dc
Logic Module
Display Module
Ethernet Port
USB Ports
Serial Port
CompactFlash Card Slot
The logic module contains:
• 24V dc input (18…32V) or ac input (85…264V).
• SDRAM and flash memory, various sizes.
• 10/100 BaseT Ethernet port.
• serial RS-232 port for file transfers, printing, and logic controller
communications.
• two USB ports for attaching mouse, keyboard, or printer.
• card slot for Type I CompactFlash cards.
• battery-backed real-time clock.
Publication 2711P-UM001F-EN-P - March 2007
Overview
19
Logic Modules and CompactFlash
The logic module is available with or without internal CompactFlash.
The contents of the internal CompactFlash is what differentiates a
PanelView Plus device from a PanelView Plus CE device.
• For the PanelView Plus terminals, the internal CompactFlash
contains RSView Machine Edition software and flash memory.
• For the PanelView Plus CE terminals, the internal CompactFlash
contains the open Windows CE operating system,
RSView Machine Edition software, and flash memory.
The internal CompactFlash is available in different sizes and can be
ordered separately or bundled with the logic module.
Communication Modules
You can attach a communication module with a network interface to
the base-configured unit of the terminal to increase your
communication capability with these networks:
• DH+/DH-485/Remote I/O
• DeviceNet
• ControlNet
The communication module installs easily on top of the logic module
on the back of the unit.
Communication Module
Power Options
The base-configured units of the 700 to 1500 PanelView Plus terminals
are available with either ac (85…264V) or dc (18…32V) power input
providing application flexibility.
For dc applications using ac power, a remote ac-to-dc power supply,
cat. no. 2711P-RSACDIN, is available for DIN-rail mounting.
Publication 2711P-UM001F-EN-P - March 2007
20
Overview
Display Modules
The terminals offer a range of TFT color graphic displays with either
keypad, touch screen, or keypad and touch screen support.
• 700 (6.5 in.)
• 1000 (10.4 in.)
• 1250 (12.1 in.)
• 1500 (15 in.)
The 700 and 1250 touch displays are available in conformal-coated
options. A 1250 high-bright, touch display module is available for
outdoor installations. Plus the 1250 and 1500 touch displays offer an
integral antiglare overlay.
All displays have common features and firmware providing for easy
migration to a larger display. Field-replaceable bezels are also
available.
Touch Screen
All touch-screen displays are analog resistive and similar except for
size.
Replaceable ID Label
Touch Screen
IMPORTANT
Publication 2711P-UM001F-EN-P - March 2007
Use a plastic stylus device with a minimum tip radius of 1 mm
(0.040 in.) to prevent damage to the touch screen.
Overview
21
Keypad or Keypad and Touch
All displays are similar except for size and the number of function
keys available.
Allen-Bradley Label
Numeric Keypad
Backspace
and Enter Keys
Programmable Function Keys
(optional custom legends)
Tab and Shift Keys
Esc, CT, Alt Keys
Navigation Keys
Programmable Function Keys
(optional custom legends)
The Kxx and Fxx function keys on the keypad terminals are
programmable.
Function Keys
Description
Function Keys
700
(F1 through F10, K1 through K12)
1000
(F1 through F16, K1 through K16)
1250
(F1 through F20, K1 through K20)
1500
(F1 through F20, K1 through K20)
Programmable keys that initiate functions
on terminal display. Replaceable legends
are available for the terminals allowing for
custom function key labels.
Numeric Keypad
0…9, ., -, Backspace, Enter, Left and Right
tab, Shift, Esc, Ctrl, Alt keys.
Navigation Keys
Use the arrow keys to move cursor in lists
and select objects.
Alt+arrow key activates home, end, page
up, page down functions.
Publication 2711P-UM001F-EN-P - March 2007
22
Overview
Catalog Number
Configuration
2711P-
The table shows the catalog number configuration for configured
versions of the PanelView Plus and PanelView Plus CE terminals.
Input
Type
Display
Size
Display Type
Communication(1)
Power
Logic Module with
Flash and RAM Memory (2)
|
|
|
|
|
|
K = Keypad
4 = 3.8 in.
C = Color
PanelView Plus 400 and 600 Terminals
A = ac
1= Logic Module 64 MB
T = Touch
6 = 5.5 in.
M=Grayscale
1 = Remote I/O (single rack), Ethernet,
RS-232 & USB
D = dc
2 = Logic Module 128 MB
B = Keypad/Touch
7 = 6.5 in.
3 = DH-485, Ethernet, RS-232 & USB
3 = Logic Module with 256 MB
10 = 10.4 in.
5 = RS-232 & USB
6 = CE Logic Module with 128 MB
12 = 12.1 in.
8 = DH+, Ethernet, RS-232 & USB
7 = CE Logic Module with 256 MB
15 = 15 in.
10 = DeviceNet, Ethernet, RS-232 & USB
15 = ControlNet, Ethernet, RS-232 & USB
20 = Ehernet, RS-232 & USB plus
Communication Module Interface
PanelView Plus 700 to 1500 Terminals
4 = Ethernet, RS-232 & (2) USB
6 = DH+, DH-485, RIO, Ethernet, RS-232 & (2) USB
15 = ControlNet, Ethernet, RS-232 & (2) USB
(1)
PanelView Plus devices are not available with DeviceNet communication as a pre-assembled option. You can install a DeviceNet communication module,
cat. no. 2711P-RN10H, to a base-configured unit.
(2)
Applies to PanelView Plus 700 to 1500 terminals only.
PanelView Plus Product
Components
Components are available as separate catalog numbers for field
installation or replacement.
Display Modules (700 to 1500 only)
Publication 2711P-UM001F-EN-P - March 2007
Cat. No.
Description
2711P-RDK7C
700 keypad color display
2711P-RDT7C
700 touch color display
2711P-RDB7C
700 keypad and touch color display
2711P-RDT7CK
Conformal-coated 700 touch color display
2711P-RDK10C
1000 keypad color display
2711P-RDT10C
1000 touch color display
2711P-RDB10C
1000 keypad and touch color display
2711P-RDK12C
1250 keypad color display
2711P-RDT12C
1250 touch color display
2711P-RDT12AG
1250 touch color display with antiglare overlay
2711P-RDT12CK
Conformal-coated 1250 touch color display
2711P-RDT12H
1250 high-bright touch color display
2711P-RDB12C
1250 keypad and touch color display
2711P-RDK15C
1500 keypad color display
Overview
23
Display Modules (700 to 1500 only)
Cat. No.
Description
2711P-RDT15C
1500 touch color display
2711P-RDT15AG
1500 touch color display with antiglare overlay
2711P-RDB15C
1500 keypad and touch color display
Logic Modules (700 to 1500 only)
Cat. No.
Description
Standard Logic Modules for PanelView Plus Terminals
2711P-RP
Logic module without flash/RAM memory, dc input
2711P-RPA
Logic module without flash/RAM memory, ac input
2711P-RP1
Logic module with 64 MB flash/64 MB RAM, dc input
2711P-RP1A
Logic module with 64 MB flash/64 MB RAM, ac input
2711P-RP2
Logic module with 128 MB flash/128 MB RAM, dc input
2711P-RP2A
Logic module with 128 MB flash/128 MB RAM, ac input
2711P-RP2K
Conformal-coated logic module with 128 MB flash/128 MB RAM, dc
input
2711P-RP3
Logic module with 256 MB flash/256 MB RAM, dc input
2711P-RP3A
Logic module with 256 MB flash/256 MB RAM, ac input
CE Logic Modules for PanelView Plus CE Terminals
2711P-RP6
CE logic module with 128 MB flash/128 MB RAM, dc input
2711P-RP6A
CE logic module with 128 MB flash/128 MB RAM, ac input
2711P-RP6K
CE conformal-coated logic module with 128 MB flash/128 MB RAM,
dc input
2711P-RP7
CE logic module with 256 MB flash/256 MB RAM, dc input
2711P-RP7A
CE logic module with 256 MB flash/256 MB RAM, ac input
Communication Modules
Terminal Type
400 and 600
700 to 1500
Cat. No.
Description
2711P-RN1
Single-rack remote I/O communication module
2711P-RN3
DH-485 communication module
2711P-RN8
DH+ communication module
2711P-RN10C
DeviceNet communication module
2711P-RN15C
ControlNet communication module
2711P-RN22C
RS-232 isolated communication module
2711P-RN6
DH+/DH-485/remote I/O communication module
2711P-RN10H
DeviceNet communication module
2711P-RN15S
ControlNet communication module
Publication 2711P-UM001F-EN-P - March 2007
24
Overview
Cat. No.
Description
Internal CompactFlash for Standard Logic Modules
2711P-RW1
64 MB CompactFlash with RSView Machine Edition software
2711P-RW2
128 MB CompactFlash with RSView Machine Edition software
2711P-RW3
256 MB CompactFlash with RSView Machine Edition software
Internal CompactFlash for CE Logic Modules
2711P-RW6
128 MB CompactFlash with RSView Machine Edition software and the
open Windows CE operating system for the CE logic module
2711P-RW7
256 MB CompactFlash with RSView Machine Edition software and the
open Windows CE operating system for the CE logic module
2711P-RW8
512 MB CompactFlash with RSView Machine Edition software and the
open Windows CE operating system for the CE logic module
RAM Memory (700 to 1500 only)
Cat. No.
Description
2711P-RR64
64 MB SODIMM memory
2711P-RR128
128 MB SODIMM memory
2711P-RR256
256 MB SODIMM memory
Compact Flash Cards (Blank)
Cat. No.
Description
2711P-RC2
128 MB blank CompactFlash card
2711P-RC3
256 MB blank CompactFlash card
2711P-RC4
512 MB blank CompactFlash card
2711P-RCH
CompactFlash to PCMCIA adapter
Legend Kits
Cat. No.
Description
2711P-RFK6
Replacement legends strips for 600 keypad terminal
2711P-RFK7
Replacement legends strips for 700 keypad terminal
2711P-RFK10
Replacement legends strips for 1000 keypad terminal
2711P-RFK12
Replacement legends strips for 1250 keypad terminal
2711P-RFK15
Replacement legends strips for 1500 keypad terminal
Backlights (700 to 1500 only)
Publication 2711P-UM001F-EN-P - March 2007
Cat. No.
Description
2711P-RL7C
Replacement color backlight for 700 series A displays
2711P-RL7C2
Replacement color backlight for 700 series B displays
2711P-RL10C
Replacement color backlight for 1000 displays
2711P-RL10C2
Replacement color backlight for 1000 series B and C displays
Overview
25
Backlights (700 to 1500 only)
Cat. No.
Description
2711P-RL12C
Replacement color backlight for 1250 series A and B displays
2711P-RL12C2
Replacement color backlight for 1250 series C displays
2711P-RL15C
Replacement color backlight for 1500 series B displays
Replacement Bezels
Cat. No.
Description
2711P-RBK7
Replacement bezel for 700 keypad terminal
2711P-RBT7
Replacement bezel for 700 touch terminal
2711P-RBB7
Replacement bezel for 700 keypad or keypad/touch terminal
2711P-RBK10
Replacement bezel for 1000 keypad terminal
2711P-RBT10
Replacement bezel for 1000 touch terminal
2711P-RBB10
Replacement bezel for 1000 keypad or keypad/touch terminal
2711P-RBK12
Replacement bezel for 1250 keypad terminal
2711P-RBT12
Replacement bezel for 1250 touch terminal
2711P-RBT12
Replacement bezel for 1250 high-bright touch terminal
2711P-RBB12
Replacement bezel for 1250 keypad or keypad/touch terminal
2711P-RBK15
Replacement bezel for 1500 keypad terminal
2711P-RBT15
Replacement bezel for 1500 touch terminal
2711P-RBB15
Replacement bezel for 1500 keypad or keypad/touch terminal
Protective Antiglare Overlays
Cat. No.(1)
Description
2711P-RGK4
Antiglare overlay for PanelView Plus 400 keypad terminal
2711P-RGK6
Antiglare overlay for PanelView Plus 600 keypad or keypad/touch terminal
2711P-RGT6
Antiglare overlay for PanelView Plus 600 touch terminal
2711P-RGK7
Antiglare overlay for PanelView Plus 700 keypad or keypad/touch terminal
2711P-RGT7
Antiglare overlay for PanelView Plus 700 touch terminal
2711P-RGK10
Antiglare overlay for PanelView Plus 1000 keypad or keypad/touch terminal
2711P-RGT10
Antiglare overlay for PanelView Plus 1000 touch terminal
2711-RGK12
Antiglare overlay for PanelView Plus 1250 keypad or keypad/touch terminal
2711P-RGT12
Antiglare overlay for PanelView Plus 1250 touch and high-bright touch
terminal
2711P-RGK15
Antiglare overlay for PanelView Plus 1500 keypad or keypad/touch terminal
2711P-RGT15
Antiglare overlay for PanelView Plus 1500 touch terminal
(1)
All catalog numbers ship with a quantity of three overlays.
Publication 2711P-UM001F-EN-P - March 2007
26
Overview
Adapter Plates
Cat. No.
Description
2711P-RAK4
Adapts a PanelView Plus 400 keypad terminal to a PanelView
Standard 550 keypad cutout
2711P-RAK6
Adapts a PanelView Plus 600 keypad terminal to a PanelView
Standard 600 keypad cutout
2711P-RAK7
Adapts a PanelView Plus 700 keypad terminal to a PanelView
Standard 900 keypad cutout
2711P-RAT7
Adapts a PanelView Plus 700 touch terminal to a PanelView
Standard 900 touch cutout
2711P-RAK10
Adapts a PanelView Plus 1000 keypad terminal to a PanelView
1000/1000E keypad cutout
2711P-RAT10
Adapts a PanelView Plus 1000 touch terminal to a PanelView
1000/1000E touch cutout
2711P-RAK12E
Adapts a PanelView Plus 1250 (or PV1000/1000E) keypad
terminal to a PanelView 1200/1400E keypad cutout
2711P-RAT12E2
Adapts a PanelView Plus 1250 (or PV1000/1000E) touch terminal
to a PanelView 1200E touch cutout
2711P-RAT12E
Adapts a PanelView Plus 1250 (or PV1000/1000E) touch terminal
to a PanelView 1400E touch cutout
2711P-RAK12S
Adapts a PanelView Plus 1250 (or PV1000/1000E) keypad
terminal to a PanelView Standard 1400 keypad cutout
2711P-RAT12S
Adapts a PanelView Plus 1250 (or PV1000/1000E) touch terminal
to a PanelView Standard 1400 touch cutout
2711P-RAK15
Adapts a PanelView Plus 1500 keypad or keypad/touch terminal
to a PanelView 1200E/1400E keypad terminal
2711P-RAT15
Adapts a PanelView Plus 1500 touch terminal to a PanelView
1400E touch cutout
Cables
Publication 2711P-UM001F-EN-P - March 2007
Cat. No.
Description
2711-NC13
RS-232 operating/programming cable (9-pin D-shell to 9-pin D-shell), 5 m
(16.4 ft)
2711-NC14
RS-232 operating/programming cable (9-pin D-shell to 9-pin D-shell), 10 m
(32.7 ft)
2711-NC17
Remote RS-232 serial cable (9-pin D-shell to 9-pin D-shell)
2711-NC21
RS-232 operating cable (9-pin D-shell to 8-pin mini DIN), 5 m (16.4 ft)
2711-NC22
RS-232 operating cable (9-pin D-shell to 8-pin mini DIN), 10 m (32.7 ft)
1761-CBL-AS03
DH-485 operating cable (6-pin Phoenix to RJ45), 3 m (10 ft)
1761-CBL-AS09
DH-485 operating cable (6-pin Phoenix to RJ45), 9 m (30 ft)
1746-C10
DH-485 network interface cable (SDL AMP to RJ45), 1.83 m (6 ft)
1746-C11
DH-485 network interface cable (SDL AMP to RJ45), .3 m (1 ft.)
1784-CP14
DH-485 network interface cable (5-pin Phoenix to RJ45)
2711P-CBL-EX04
Ethernet CAT5 crossover cable, industrial grade, 4.3 m (14 ft)
Overview
27
Communication Adapters
Cat. No.
Description
1761-NET-AIC
AIC+ advanced interface converter
1747-AIC
DH-485 isolated link coupler for use with DH-485 communication modules
(2711P-RN3, 2711P-RN6)
Remote AC Power Supply (700 to 1500 only)
Cat. No.
Description
2711P-RSACDIN
DIN-rail power supply, ac-to-dc, 85…265V ac, 47…63 Hz
Miscellaneous
Cat. No.
Description
2711P-RVT12
Solar visor for outdoor high-bright 1250 touch screen display modules
2711P-RY2032
Replacement battery for 700 to 1500 terminals
2711P-RTMC
Replacement mounting clips for 700 to 1500 terminals, quantity of 8
2711P-RTFC
Replacement mounting levers for 400 and 600 terminals, quantity of 8
2711P-RVAC
Replacement ac power terminal block for 400 and 600 terminals
2711-TBDC
Replacement dc power terminal block for 400 and 600 terminals
2711P-RTBDC3 (1)
Three-position terminal block for dc logic modules, series A to D
2711P-RTBDC2 (1)
Two-position terminal block for dc logic modules, series E or later
2711P-RTBAC3(1)
Three-position terminal block for all ac logic modules
(1)
Catalog numbers ship with a quantity of ten.
Firmware Upgrade Kits
Cat. No.
Description
2711P-RU310
PanelView Plus media kit includes firmware upgrade wizard, one firmware
license, certificate of authenticity, end user license agreement.
2711P-RUA310 PanelView Plus advanced media kit includes the 2711P-RU310 media kit,
PCMCIA to compact flash adapter, and 32 MB CompactFlash card.
2711P-RUL01
Firmware upgrade license kit with one PanelView Plus firmware license. (1)
2711P-RUL05
Firmware upgrade license kit with five PanelView Plus firmware licenses. (1)
2711P-RUL10
Firmware upgrade license kit with 10 PanelView Plus firmware licenses.(1)
2711P-RUL25
Firmware upgrade license kit with 25 PanelView Plus firmware licenses. (1)
2711P-RUL50
Firmware upgrade license kit with 50 PanelView Plus firmware licenses. (1)
(1)
Also includes certificate of authenticity, end user license agreement, installation instructions.
Publication 2711P-UM001F-EN-P - March 2007
28
Overview
Publication 2711P-UM001F-EN-P - March 2007
Chapter
2
Installation
Chapter Objectives
This chapter provides pre-installation information and procedures on
how to install the terminals.
• Hazardous locations
• Environment and enclosure
• Outdoor installation for 1250 high-bright display module
• Required tools
• Clearances
• Panel cutout dimensions
• Mount the 400 or 600 terminal in a panel
• Mount the 700 to 1500 terminals in a panel
• Product dimensions
Hazardous Locations
This equipment is suitable for these locations:
• Class I, Division 2, Groups A, B, C, D.
• Class I, Zone 2, Group IIC.
• Class II, Division 2, Groups F, G.
• Class III.
• ordinary, nonhazardous locations.
The following statement applies to use in hazardous locations.
WARNING
Explosion Hazard
• Substitution of components may impair suitability for hazardous
locations.
• Do not disconnect equipment unless power has been switched off
and area is known to be nonhazardous.
• Do not connect or disconnect components unless power has been
switched off.
• All wiring must comply with N.E.C. articles 501, 502, 503, and/or
C.E.C. section 18-1J2 as appropriate.
• Peripheral equipment must be suitable for the location in which it is
used.
The dc powered terminals have a temperature code of T4 when
operating in a 55 °C (131 °F) maximum ambient temperature. Do not
install the terminals in environments where atmospheric gases have
ignition temperatures less than 135 °C (275 °F).
29
Publication 2711P-UM001F-EN-P - March 2007
30
Installation
The ac powered terminals have a temperature code of T3 when
operating in a 55 °C (131 °F) maximum ambient temperature. Do not
install the terminals in environments when atmospheric gases have
ignition temperatures less than 200 °C (392 °F).
USB Ports
The terminals contain universal serial bus (USB) ports that comply
with hazardous location environments. The 400 and 600 terminals
have one USB port; the 700 to 1500 terminals have two USB ports.
This section details the field-wiring compliance requirements and is
provided in accordance with the National Electrical Code, article 500.
PanelView Plus 400/600 Host Product
USB Port
Associated Nonincendive Field
Wiring Apparatus
USB
Peripheral
Device
The USB peripheral device must be rated for use in the hazardous
location environment in which it is used and also comply with the
circuit parameters in Table 2.2.
The circuit parameters in Table 2.1 define the maximum voltage and
current of the USB ports on the terminal.
Table 2.1, PanelView Plus USB Port Circuit Parameters
Parameter
Value
Parameter Definition
Voc
5.25V dc
Open circuit voltage of the host USB port.
Isc
1.68 A
Maximum output current of the host USB port.
The circuit parameters in Table 2.2 define the maximum voltage,
current, capacitance, and inductance values for any peripheral device
connected to a PanelView Plus USB port in a hazardous location
environment.
Publication 2711P-UM001F-EN-P - March 2007
Installation
31
Table 2.2, Required Circuit Parameters for the USB Peripheral Device
Parameter
Value
Parameter Definition and Application Requirement
Vmax
5.25V dc
Maximum applied voltage rating of the USB peripheral device.
Vmax shall be greater than or equal to Voc in Table 2.1 (Vmax ≥ Voc ).
Imax
1.68 A
Maximum current to which the USB peripheral device can be
subjected. Imax shall be greater than or equal to Isc in Table 2.1
(Imax ≥ Isc).
Ca
10 µF
Maximum allowed capacitance of the USB peripheral device and its
associated cable. The sum of Cint of the USB peripheral device and
Ccable of the associated cable shall be less than or equal to Ca
(Cint + Ccable ≤ Ca).
La
15 µH
Maximum allowed inductance of the USB peripheral device and its
associated cable. The sum of Lint of the USB peripheral device and
Lcable of the associated cable shall be less than or equal to La
(Lint + Lcable ≤ La).
Application Information
Per the National Electrical Code, the circuit parameters of associated
field-wired apparatus for use in hazardous locations shall be
coordinated with the host product such that their combination
remains nonincendive. The PanelView Plus terminal and the USB
peripheral device shall be treated in this manner.
The circuit parameters of the PanelView Plus USB ports are given in
Table 2.1. The USB peripheral device and its associated cabling shall
have circuit parameters with the limits given in Table 2.2 for them to
remain nonincendive when used with the PanelView Plus USB port. If
cable compliance and inductance are not known, use the following
values from UL 913:
Ccable = 60 pF/ft
Lcable = 0.20 µH/ft
Publication 2711P-UM001F-EN-P - March 2007
32
Installation
Environment and Enclosure
ATTENTION
This equipment is intended for use in a Pollution Degree 2 industrial
environment, in overvoltage Category II applications (as defined in IEC
publication 60664-1), at altitudes up to 2000 m (6561 ft) without
derating.
This equipment is considered Group 1, Class A industrial equipment
according to IEC/CISPR Publication 11. Without appropriate precautions,
there may be potential difficulties ensuring electromagnetic
compatibility in other environments due to conducted as well as radiated
disturbance.
This equipment is supplied as open-type equipment. It must be mounted
within an enclosure that is suitably designed for those specific
environmental conditions that will be present and appropriately designed
to prevent personal injury resulting from accessibility to live parts. The
interior of the enclosure must be accessible only by the use of a tool. The
terminals meet specified NEMA Type and IEC ratings only when
mounted in a panel or enclosure with the equivalent rating. Subsequent
sections of this publication may contain additional information regarding
specific enclosure type ratings that are required to comply with certain
product safety certifications.
In addition to this publication, see:
• Industrial Automation Wiring and Grounding Guidelines, for
additional installation requirements, Allen-Bradley publication
1770-4.1.
• NEMA Standards publication 250 and IEC publication 60529, as
applicable, for explanations of the degrees of protection provided by
different types of enclosure.
For more enclosure and certification information, refer to the
PanelView Plus/PanelView Plus CE Outdoor High-bright Display
Modules Installation Instructions, publication 2711P-IN026.
Outdoor Installation for
High-bright Displays
When using the high-bright display module, cat. no. 2711P-RDT12H,
outdoors, considerations in maximizing the field life of the front bezel
and display are:
• selecting the proper enclosure.
• orientation of the terminal.
Both ultraviolet and infrared radiation can reduce the field life of any
electronic device. While the materials used in the terminal bezels
provide long field life, that life can be extended by proper installation.
Ultraviolet radiation from the sun causes all plastics to fade or yellow
and become brittle over time. Using an antiglare overlay, cat. no.
2711P-RGT12, will protect the front of the terminal from direct
exposure to UV radiation and greatly increase its field life.
Publication 2711P-UM001F-EN-P - March 2007
Installation
33
When installing the high-bright display module in an environment
where the front of the terminal will be in direct sunlight during the
hottest part of the day and the external ambient temperature can
exceed 40 °C (104 °F), use the visor kit, cat. no. 2711P-RVT12. The
visor reduces the solar load on the front of the display and helps to
maintain internal temperatures within specification.
The high-bright display module has a built-in temperature sensor that
automatically reduces the backlight intensity if the temperature inside
the cabinet exceeds 55 °C (131 °F). This reduces the risk of damage to
the display.
The paint color, size, and power dissipated by the internal
components of an enclosure affect the temperature rise inside the
cabinet. Hoffman, a Rockwell Automation Encompass Partner, has
information to assist you with enclosure selection and heating/cooling
accessories to meet the temperature requirements of the installed
equipment. See website http://www.hoffmanonline.com.
Stirring fans or active cooling may be required in high altitude and
high ambient temperature locations to keep the internal enclosure
temperature below 55 °C (131 °F). Use a heater in installations where
the ambient temperature is below 0 °C (32 °F).
The backlight of the high-bright display generates a significant amount
of heat when set to full intensity. To minimize the amount of heat
generated and extend the life of the backlight, decrease the display
intensity by using the screen saver with a 5…10 minute delay.
Avoid placing the terminal on the south (north in the southern
hemisphere) or west side of the cabinet, if possible. This will reduce
the heat rise due to solar loading during the hottest part of the day.
Mount the terminal vertically to minimize solar loading on the display.
Do not mount the terminal in a sloped enclosure if it will be exposed
to direct sunlight.
Required Tools
These tools are required for panel installation:
• Panel cutout tools
• Small, slotted screwdriver
• Torque wrench (lb-in) for tightening the mounting clips on the
PanelView Plus 700 to 1500 and PanelView Plus CE terminals
Publication 2711P-UM001F-EN-P - March 2007
34
Installation
Clearances
Allow adequate clearance around the terminal, inside the enclosure,
for adequate ventilation. Consider heat produced by other devices in
the enclosure. The ambient temperature around the terminals must be
between 0…55 °C (32…31 ºF).
Clearance Area 400 and 600 Terminals
700 to 1500 Terminals
Top
51 mm (2 in.)
51 mm (2 in.)
102 mm (4 in.)
51 mm (2 in.)
Side
25 mm (1 in.)
25 mm (1 in.)
Back
None
25 mm (1 in.)
Bottom
(1)
(1)
Cutout Dimensions
Minimum side clearance for insertion of memory card and cable wiring is 102 mm (4 in.).
Use the full size template shipped with your terminal to mark the
cutout dimensions.
Terminal Type
Height mm (in.)
Width mm (in.)
400 Keypad
123 (4.86)
156 (6.15)
600 Keypad or Keypad and Touch
142 (5.61)
241 (9.50)
600 Touch
123 (4.86)
156 (6.15)
PanelView Plus 400 and 600 Terminals
PanelView Plus and PanelView Plus CE 700 to 1500 Terminals
Mount the 400 or 600
Terminal in a Panel
700 Keypad or Keypad and Touch
167 (6.57)
264 (10.39)
700 Touch
154 (6.08)
220 (8.67)
1000 Keypad or Keypad and Touch
224 (8.8)
375 (14.75)
1000 Touch
224 (8.8)
305 (12.00)
1250 Keypad or Keypad and Touch
257 (10.11)
390 (15.35)
1250 Touch and 1250 High-bright Touch
257 (10.11)
338 (13.29)
1500 Keypad or Keypad and Touch
305 (12.00)
419 (16.50)
1500 Touch
305 (12.00)
391 (15.40)
Mounting levers secure the terminal to the panel. The number of
levers you use (4 or 6) varies by terminal type.
ATTENTION
• Disconnect all electrical power from the panel before making the
panel cutout.
• Make sure the area around the panel cutout is clear.
• Take precautions so metal cuttings do not enter any components
already installed in the panel.
• Failure to follow these warnings may result in personal injury or
damage to panel components.
Publication 2711P-UM001F-EN-P - March 2007
Installation
35
Follow these steps to mount the 400 or 600 terminals in a panel.
1. Cut an opening in the panel by using the panel cutout shipped
with the terminal.
2. If a communication module is ordered separately, attach the
module to the base unit before panel installation.
Refer to the instructions shipped with module.
3. Make sure the terminal sealing gasket is properly positioned on
the terminal.
This gasket forms a compression-type seal. Do not use sealing
compounds.
Sealing Gasket
4. Install legend strips before installing the terminal if you are
using keypad legend strips on a 600 keypad terminal.
Be careful not to pinch legend strip during installation.
5. Place the terminal in the panel cutout.
If installing the terminal in an existing 550 panel cutout, align
the terminal with the center of the cutout for best gasket sealing.
6. Insert all mounting levers into the mounting slots on the
terminal.
Slide each lever until the flat side of the lever touches the
surface of the panel.
Mounting Slots
Flat Side of Lever
Mounting Levers
7. When all levers are in place, slide each lever an additional notch
or two until you hear a click.
Publication 2711P-UM001F-EN-P - March 2007
36
Installation
8. Rotate each lever in the direction indicated until it is in the final
latch position.
Follow the latching sequence for the optimum terminal fit.
1
4
4 Levers
Notch
6
3
1
Alignment Marks
Rotate lever until notch in
lever aligns with proper
alignment mark on terminal.
1
2
5
3
6 Levers
4
2
6
Use this table as a guide to provide an adequate gasket seal
between the terminal and the panel.
Lever Position
1
3 2
6 5 4
Terminal Markings
or Alignment
Typical Gauge
1
0.15…2.01 mm (0.060…0.079 in.)
16
2
2.03…2.64 mm (0.08…0.104 in.)
14
3
2.67…3.15 mm (0.105…0.124 in.)
12
4
3.17…3.66 mm (0.125…0.144 in.)
10
5
3.68…4.16 mm (0.145…0.164 in.)
8/9
6
4.19…4.75 mm (0.165…0.187 in.)
7
ATTENTION
Publication 2711P-UM001F-EN-P - March 2007
Panel Thickness Range
Follow instructions to provide a proper seal and to
prevent potential damage to the product. Allen-Bradley
assumes no responsibility for water or chemical damage
to the terminal or other equipment within the enclosure
because of improper installation.
Installation
Mount the 700 to 1500
Terminal in a Panel
37
Mounting clips secure the terminal to the panel. The number of clips
you use (4, 6, or 8) varies by terminal type.
ATTENTION
• Disconnect all electrical power from the panel before making the
panel cutout.
• Make sure the area around the panel cutout is clear.
• Take precautions so metal cuttings do not enter any components
already installed in the panel.
• Failure to follow these warnings may result in personal injury or
damage to panel components.
Follow these steps to mount a 700 to 1500 terminal in a panel.
1. Cut an opening in the panel by using the panel cutout shipped
with the terminal.
2. Make sure the terminal sealing gasket is properly positioned on
the terminal.
This gasket forms a compression-type seal. Do not use sealing
compounds.
Sealing Gasket
3. Install the legend strips before installing the terminal if you are
using keypad legend strips on keypad terminals.
Be careful not to pinch the legend strip during installation.
4. Place the terminal in the panel cutout.
Publication 2711P-UM001F-EN-P - March 2007
38
Installation
5. Slide the ends of the mounting clips into the slots on the
terminal.
Mounting Clip
Mounting Clip Slot
6. Tighten the mounting clip screws by hand until the gasket seal
contacts the mounting surface uniformly.
7. Tighten the mounting clips screws to a torque of 0.90…1.1 Nm
(8…10 lb-in) by using the specified sequence, making sure not
to over-tighten.
1
4
1
Torque Sequence
for 4 Clips
3
2
5
Torque Sequence
for 6 Clips
4
2
1
3
3
6
Torque Sequence
for 8 Clips
Publication 2711P-UM001F-EN-P - March 2007
8
4
7
5
ATTENTION
6
2
Tighten the mounting clips to the specified torque to
provide a proper seal and to prevent damage to the
product. Allen-Bradley assumes no responsibility for
water or chemical damage to the product or other
equipment within the enclosure because of improper
installation.
Installation
Product Dimensions
39
Product dimensions for each terminal are in mm (in.).
PanelView Plus 400 Dimensions
152
(6.0)
185 (7.28)
60
(2.35)
90
3.54)
71 (2.81)
154 (6.08)
Publication 2711P-UM001F-EN-P - March 2007
40
Installation
PanelView Plus 600 Dimensions
600 Keypad or Keypad/Touch Terminal
167
(6.58)
68
(2.68)
98
(3.86)
71 (2.81)
268 (10.47)
154 (6.08)
600 Touch Terminal
152
(6.0)
68
(2.68)
98
(3.86)
71 (2.81)
185 (7.28)
Publication 2711P-UM001F-EN-P - March 2007
154 (6.08)
Installation
41
The depth dimensions are shown for:
• base-configured unit (display module and logic module).
• base-configured unit with communication module.
PanelView Plus and PanelView Plus CE 700 Dimensions
700 Keypad or Keypad/Touch Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
193
(7.58)
b
a
290
(11.40)
700 Touch Screen Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
179
(7.04)
b
a
246
(9.68)
Publication 2711P-UM001F-EN-P - March 2007
42
Installation
The depth dimensions are shown for:
• base-configured unit (display module and logic module).
• base-configured unit with communication module.
PanelView Plus and PanelView Plus CE 1000 Dimensions
1000 Keypad or Keypad/Touch Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
248
(9.77)
b
a
399
(15.72)
1000 Touch Screen Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
248
(9.77)
b
329
(12.97)
Publication 2711P-UM001F-EN-P - March 2007
a
Installation
43
The depth dimensions are shown for:
• base-configured unit (display module and logic module).
• base-configured unit with communication module.
PanelView Plus and PanelView Plus CE 1250 Dimensions
1250 Keypad or Keypad/Touch Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
282
(11.12)
b
a
416
(16.36)
1250 Touch Screen Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
a
b
282
(11.12)
1250
a 74 (2.90) Display to Logic Module
b 101 (3.99) Display to Communication Module
363
(14.30)
b
a
1250 High-bright
Publication 2711P-UM001F-EN-P - March 2007
44
Installation
The depth dimensions are shown for:
• base-configured unit (display module and logic module).
• base-configured unit with communication module.
PanelView Plus and PanelView Plus CE 1500 Dimensions
1500 Keypad or Keypad/Touch Terminal
a 65 (2.55) Display to Logic Module
b 93 (3.65) Display to Communication Module
330
(12.97)
b
a
419
(18.46)
1500 Touch Screen Terminal
a 65 (2.55) Display to Logic Module
b 93 (3.65) Display to Communication Module
330
(12.97)
b
416
(16.37)
Publication 2711P-UM001F-EN-P - March 2007
a
Chapter
3
Power Connections
Chapter Objectives
This chapter covers wiring and safety guidelines, and provides
procedures to:
• remove and install the power terminal block.
• connect dc power.
• connect ac power.
• reset the terminal.
Wiring and Safety
Guidelines
Use publication NFPA 70E Electrical Safety Requirements for
Employee Workplaces, IEC 60364 Electrical Installations in Buildings,
or other applicable wiring safety requirements for the country of
installation when wiring the devices. In addition to the NFPA
guidelines:
• connect the device and other similar electronic equipment to its
own branch circuit.
• protect the input power by a fuse or circuit breaker rated at no
more than 15 A.
• route incoming power to the device by a separate path from the
communication lines.
• cross power and communication lines at right angles if they
must cross.
Communication lines can be installed in the same conduit as
low-level dc I/O lines (less than 10V).
• shield and ground cables appropriately to avoid electromagnetic
interference (EMI).
Grounding minimizes noise from EMI and is a safety measure in
electrical installations.
For more information on grounding recommendations, refer to the
National Electrical Code published by the National Fire Protection
Association.
For more information, refer to Wiring and Grounding Guidelines for
PanelView Plus Devices, publication 2711P-TD001. You can locate this
publication in the literature library at this website:
http://literature.rockwellautomation.com.
45
Publication 2711P-UM001F-EN-P - March 2007
46
Power Connections
Remove and Install the
Power Terminal Block
The terminals ship with the power terminal block installed. You can
remove the terminal block for ease of installation, wiring, and
maintenance.
WARNING
Explosion Hazard
• Substitution of components may impair suitability for hazardous
locations.
• Do not disconnect equipment unless power has been switched off
and area is known to be nonhazardous.
• Do not connect or disconnect components unless power has been
switched off.
• All wiring must comply with N.E.C. articles 501, 502, 503, and/or
C.E.C. section 18-1J2 as appropriate.
• Peripheral equipment must be suitable for the location in which it is
used.
ATTENTION
Disconnect all power before installing or replacing components.
Failure to disconnect power may result in electrical shock or
damage to the terminal.
400 and 600 Terminals
ATTENTION
The ac and dc terminal blocks are keyed and marked differently
so be sure to follow markings. Do not force terminal blocks into
connectors to prevent potential damage to terminal.
Follows these steps to remove the terminal block in the PanelView
400 and 600 terminals.
1. Insert the tip of small, flat-blade, screwdriver into the terminal
block access slot.
Publication 2711P-UM001F-EN-P - March 2007
Power Connections
47
2. Gently pry the terminal block away from terminal to release the
locking mechanism.
Follow these steps to replace the terminal block.
1. Press terminal block base in first with block leaning outward.
2. Gently push the top of the terminal block back to the vertical
position to snap in locking tab.
700 to 1500 Terminals
The terminal block used by the 700 to 1500 terminals depends on the
series of the logic module and the power input type.
• Series A to D, dc logic modules use a 3-position terminal block.
• Series E or later, dc logic modules use a 2-position terminal
block.
• All logic modules with an ac power input use a 3-position
terminal block.
Follow these steps to remove the terminal block:
1. Loosen the two screws that secure the terminal block.
Publication 2711P-UM001F-EN-P - March 2007
48
Power Connections
2. Gently pull the terminal block away from the connector.
2-position dc Terminal Block
(Series E or later)
3-position ac or dc
Terminal Block
Follow these steps to install the terminal block:
1. Reattach the terminal block to the connector until seated.
2. Tighten the two screws that secure the terminal block to the
connector.
Publication 2711P-UM001F-EN-P - March 2007
Power Connections
DC Power Connections
49
PanelView Plus terminals with an integrated, nonisolated, 24V dc
power supply have these power ratings
Power Type
dc
Terminal
Input Range
400 and 600
24V dc nom (18…30 V dc)
25 W max (1.0 A at 24V dc)
700 to 1500
24V dc nom (18…32 V dc)
70 W max (2.9 A at 24V dc)
The power supply is internally protected against reverse polarity of
the dc+ and dc- connections. Connecting dc+ or dc- to the functional
earth terminal may damage the device.
The input power terminal block supports these wire sizes.
Wire Specifications for DC Power Terminal Block
Single-wire
Dual-wire
Wire Type
Gauge
Gauge(1)
Terminal
0.45…0.56 Nm
(4…5 lb-in)
400 and 600
700 to 1500 logic module
series A to D
Stranded
or solid
Cu 90 °C (194 °F)
22…16 AWG
700 to 1500 logic module
series E and later
(1)
Terminal Screw
Torque
22…14 AWG
0.23…0.34 Nm
(2…3 lb-in)
0.56 Nm (5 lb-in)
Two-wire max. per terminal.
External Power Supply
Use a single, 24V dc power supply to power each PanelView Plus
device, such as cat. no. 2711P-RSACDIN. Using a separate, isolated
and ungrounded source to power each terminal prevents ground loop
currents from damaging the terminals.
The output on the power supply must be isolated from the input and
not connected to earth ground.
ATTENTION
Use a Class 2 or SELV supply as required by local wiring
codes for your installation. The Class 2 and SELV power
sources provide protection so that under normal and
single-fault conditions, the voltage between the conductors,
and between the conductors and functional earth or
protective earth does not exceed a safe value.
Publication 2711P-UM001F-EN-P - March 2007
50
Power Connections
Functional Earth Connection
PanelView Plus devices with a dc power input have a functional earth
terminal that you must connect to a low-impedance earth ground.
IMPORTANT
The functional earth connection to ground is mandatory. This
connection is required for noise immunity, reliability, and
Electromagnetic Compliance (EMC) with the European Union
(EU) EMC directive for CE-mark conformance.
• The 700 to 1500 terminals have the functional earth ground
connection on the rear of the display module.
• The 400 and 600 terminals have the functional earth ground
connection on the power input terminal block.
The functional earth terminal requires a minimum wire gauge.
Functional Earth Wire Specifications for DC Power
Terminal
400 and 600
700 to1500
FE Symbol
Wire Type
Stranded or solid
Wire Gauge
Cu 90 °C (194 °F)
Terminal Screw Torque
14…12 AWG
0.45…0.56 Nm (4…5 lb-in)
14…10 AWG
1.13…1.36 Nm (10…12 lb-in)
On most PanelView Plus dc terminals, the functional earth terminal is
internally connected to the dc- terminal within the product.
ATTENTION
Damage or malfunction can occur when a voltage potential
exists between two separate ground points. Make sure the
terminal does not serve as a conductive path between ground
points at different potentials.
The PanelView terminals have isolated and nonisolated
communication ports.
Refer to Chapter 7 for information on communication port Isolation.
IMPORTANT
Publication 2711P-UM001F-EN-P - March 2007
For more information, refer to Wiring and Grounding Guidelines
for PanelView Plus Devices, publication 2711P-TD001.
Power Connections
51
Connect DC Power
WARNING
Explosion Hazard - Do not disconnect equipment unless power
has been switched off and area is known to be nonhazardous.
Disconnect all power before installing or replacing components.
Failure to disconnect power may result in electrical shock or
damage to the terminal.
Follow these steps to connect the terminal to dc power.
1. Verify that the terminal is not connected to a power source.
2. Secure the dc power wires to the terminal block.
Follow the markings on terminal blocks and terminal for proper
connections.
3. Secure the functional earth ground wire.
• On the 400 and 600 terminals, secure the functional earth
ground wire to the functional-earth ground terminal on the
input power terminal block.
• On the 700 to 1500 terminals, secure the functional earth
ground wire to the functional-earth ground terminal screw at
the bottom of the display.
400 and 600 dc Terminals
700 to 1500 dc Terminals
3-position Terminal Block
(Series A to D Logic Modules)
–
+
dc - dc +
dc +
dc -
2-position Terminal Block
(Series E or later Logic Modules)
Functional Earth Ground to Ground Bus
–
Functional Earth
to Ground Bus
+
dc - dc +
4. Apply 24V dc power to the terminal.
Publication 2711P-UM001F-EN-P - March 2007
52
Power Connections
AC Power Connections
PanelView Plus devices with an integrated ac power supply have
these power ratings.
Terminal
Voltage Range
Frequency
VA
400 and 600
85…264V ac
47…63 Hz
60V A max
700 to 1500
85…264V ac
47…63 Hz
160V A max
The input power terminal block supports these wire sizes.
Wire Specifications for AC Power Terminal Block
Terminal
400 and 600
700 to 1500
(1)
Dual-wire Gauge(1)
Single-wire Gauge
22…16 AWG
22…14 AWG
0.45…0.56 Nm (4…5 lb-in)
22…16 AWG
22…14 AWG
0.56 Nm (5 lb-in)
Wire Type
Stranded
or solid
Cu 90 °C (194 °F)
Terminal Screw Torque
Two-wire max. per terminal
Protective Earth Connection
PanelView Plus devices with an ac power input have a protective
earth ground terminal that you must connect to a low-impedance
earth ground.
ATTENTION
The protective earth connection is required for both electrical
safety and Electromagnetic Compliance (EMC) with the
European Union (EU) EMC directive for CE-mark conformance.
The protective earth ground connection is on the power input
terminal block. The protective earth terminal requires a minimum wire
gauge.
Protective Earth Wire Specifications for ac Power
Terminal
400 and 600
700 to 1500
PE Symbol
Wire Type
Stranded
or solid
Publication 2711P-UM001F-EN-P - March 2007
Cu 90 °C (194
°F)
Wire Gauge
Terminal Screw Torque
14…12 AWG
0.45…0.56 Nm (4…5 lb-in)
14…12 AWG
0.56 Nm (5 lb-in)
Power Connections
53
Functional Earth Connection
The PanelView Plus 700 to 1500 devices with an ac power input also
have a functional earth connection on the back of the display.
On 700 to 1500 devices, you must connect both protective
earth and functional earth to ground.
IMPORTANT
The functional earth terminal requires a minimum wire gauge.
Functional Earth Wire Specifications for ac Power
Terminal
700 to 1500
FE Symbol
Wire Type
Stranded or solid
ATTENTION
Cu 90 °C (194 °F)
Wire Gauge
Terminal Screw Torque
14…10 AWG
1.13…1.36 Nm (10…12 lb-in)
The functional earth and protective earth connections to
ground are mandatory. The functional earth is required for
Electromagnetic Compliance (EMC) with the European Union
(EU) EMC directive for CE-mark conformance. The protective
earth ground connection is required for safety and regulatory
compliance.
Publication 2711P-UM001F-EN-P - March 2007
54
Power Connections
Connect AC Power
WARNING
Explosion Hazard - Do not disconnect equipment unless power
has been switched off and area is known to be nonhazardous.
Disconnect all power before installing or replacing components.
Failure to disconnect power may result in electrical shock or
damage to the terminal.
ATTENTION
Improper wiring of the power terminals may result in voltage at
the communication connector shells.
Do not apply power to the terminal until all wiring connections
have been made. Failure to do so may result in electrical shock.
Follow these steps to connect the terminal to ac power.
1. Verify that the terminal is not connected to a power source.
2. Secure the ac power wires to the terminal block.
Follow the markings on terminal blocks and terminal for proper
connections.
3. Secure the protective earth ground wire to the marked position
of the power input terminal block.
4. On the 700 to 1500 devices, also secure the functional earth
ground wire to the functional earth terminal screw on the back
of the display to ground bus.
400 and 600 ac Terminals
700 to 1500 ac Terminals
L1
L1
L2/Neutral
Protective Earth
to Ground Bus
L2/Neutral
Functional Earth Ground to Ground Bus
5. Apply ac power to the terminal.
Publication 2711P-UM001F-EN-P - March 2007
Protective Earth
to Ground Bus
Power Connections
Reset the Terminals
55
Use the reset switch to restart a terminal without having to disconnect
and reapply power. After a reset, the terminal performs a series of
startup tests and then either:
• runs the .MER application loaded in the terminal.
• opens the desktop on CE terminals only.
• enters Configuration mode.
The action that occurs depends on the startup options configured for
your terminal.
Refer to Chapter 9, Troubleshooting, for a list of startup information
and error messages.
Reset Switch
Reset
• On 400 to 600 terminals, press the reset switch with your finger
or a nonconductive object.
• On 700 to 1500 terminals, insert a thin, nonconductive probe
into the hole marked reset and press the switch.
ATTENTION
Use a nonconductive object to press the reset or default switch.
Do not use a conducting object such as a paper clip or you may
damage the terminal. Do not use the tip of a pencil; graphite
may damage the terminal.
Publication 2711P-UM001F-EN-P - March 2007
56
Power Connections
Publication 2711P-UM001F-EN-P - March 2007
Chapter
4
Configuration Mode
Chapter Objectives
This chapter shows how to use the Configuration mode of your
PanelView Plus terminal to:
•
•
•
•
•
•
Access Configuration Mode
perform data entry and navigation.
load an application.
run an application.
modify application settings.
modify terminal settings.
configure startup shortcuts for PanelView Plus CE devices.
Your PanelView Plus device has onboard software, RSView ME
Station, to perform and configure terminal operations. When you reset
or start the terminal, you automatically enter Configuration mode,
unless your .MER application is automatically set to run on startup.
To access Configuration mode from a running application, press the
Goto Configuration Mode button. This button is added to the
application screen in RSView Studio. The application stops running
but is still loaded.
IMPORTANT
To access Configuration mode from a running application, you
must add a Goto Configuration Mode button to an application
screen.
On PanelView Plus CE devices, you can enter Configuration mode
from the Start menu or the desktop.
• Select Start>Programs>Rockwell Software>RSView ME Station.
• Select the RSView ME Station icon on the desktop.
57
Publication 2711P-UM001F-EN-P - March 2007
58
Configuration Mode
Configuration Mode Main Screen
Name of application that is currently loaded.
Only appears if application is loaded.
Publication 2711P-UM001F-EN-P - March 2007
Terminal Operation
Description
Load Application (F1)
Opens another screen where you can select an application to
load. Once loaded, the application name will appear under
Current Application.
Run Application (F2)
Runs the .mer application displayed under Current Application.
An application must be loaded before you can run it.
Application Settings (F3)
Opens a menu of application-specific configuration settings.
Terminal Settings (F4)
Opens a menu of options to configure non-application, specific
terminal settings for the PanelView Plus device.
Delete Log Files Before
Running (F5)
Toggles between Yes and No. If you select Yes, all data log files,
alarm history and alarm status file will be deleted before the
application is run. If you select No, log files are not deleted first.
Reset (F7)
Resets the terminal. The action that occurs on startup for
PanelView Plus CE devices depends on whether you defined
shortcut paths in the Windows Startup folder. On other
PanelView Plus devices, the action on startup depends on
configured startup options.
Exit (F8)
Exits Configuration mode.
Configuration Mode
59
Navigation Buttons
Screen buttons are used for data entry and navigation.
• On touch-screen terminals, tap the button with your finger or
stylus.
• On keypad terminals, select the function key listed on the
button, or in some cases, the corresponding key on the keypad.
• If a mouse is attached, click a button.
In addition to operation specific buttons, most screens have a
combination of these buttons.
Navigation Buttons
Close
[F8]
OK
[F7]
Cancel
[F8]
Description
Returns to the previous screen.
Accepts modified values and returns to
previous screen.
Cancels the current operation without saving
any changes.
Moves highlight up or down a list.
Selects a highlighted screen or item from a list.
Publication 2711P-UM001F-EN-P - March 2007
60
Configuration Mode
Enter or Edit Data
Many screens have buttons that access fields where you must enter or
edit data. When you press the button or function key, the input panel
opens ready for you to enter data. If a field is restricted to a numeric
value, only the 0…9 keys will be enabled. If the value is an IP
address, the 0…9 and decimal point keys will be enabled. All other
buttons will be disabled.
Display Area
PanelView Plus
Character Keyboard
Controls
Input Panel Controls
Function
SHF
Switches keys between their shifted and unshifted state. The initial default is shifted.
CAPS
Switches keys between lowercase and uppercase characters. The initial default is lowercase.
SPACE
Enters a space between characters in the Display Area.
Backspace
Deletes the previous character (to the left of the cursor) in the Display Area.
Select
Selects a character and enters it in the Display Area.
Right, Left, Up, Down Arrow Keys
Selects the character to the right, left, above or below the currently selected character.
Enter
Accepts the entered characters and returns to the previous screen
ESC
Cancels the current operation and returns to the previous screen.
Follow these steps to enter characters in the display area.
1. Select a character on the character keyboard.
• On a touch-screen terminal, tap or press a key.
• On a keypad terminal, use the arrow keys on the keypad to
select a key.
• If a mouse is attached, click a key.
2. Press the Select button to copy the character to the display area.
3. Press Enter when done to exit the input panel.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
Load an Application
61
You can load a RSView ME .MER application from the internal
CompactFlash in the terminal or an external CompactFlash card.
List of .MER applications
stored in the CompactFlash of
the terminal.
Moves
highlight up
Moves
highlight down
Follows these steps to load an application.
1. Select Load Application from the main screen.
2. Press the Source button to select the storage location of the
application file you want to load.
• Internal Storage - the internal CompactFlash in the terminal.
• External Storage 1 - the external CompactFlash card loaded in
the card slot of the terminal .
• External Storage 2 - for future use.
RSView ME software only recognizes files in the
TIP
\Rockwell Software\RSViewME\Runtime\ folder.
3. Select an .MER file from the list by using the up and down
cursor keys.
4. Press the Load button to load the selected application.
You will be asked if you want to replace the terminal’s
communication configuration with the configuration in the
application.
5. Select Yes or No.
If you select Yes, any changes to the device addresses or driver
properties in the RSLinx Communications screen will be lost.
The name of the currently loaded application will appear at the top of
the main configuration screen.
Publication 2711P-UM001F-EN-P - March 2007
62
Configuration Mode
Run an Application
After loading an .MER application, you can run the application. To
load an application, select the Run Application button on the main
screen.
Log files are generated by the application. To delete the log files
before running an application, select the Delete Log Files Before
Running button on the main screen.
Application Settings
You can show device shortcuts defined for the loaded .MER
application. For example, your .MER application might have SLC
defined as a device shortcut name for the SLC 5/05 controller. Device
shortcuts are read-only and cannot be edited. To view device
shortcuts, select the Application Settings button from the main screen.
Terminal Settings
You can modify settings on the terminal that are not specific to the
application.
Publication 2711P-UM001F-EN-P - March 2007
Terminal Settings
Description
Diagnostic
Forwards diagnostic messages form a remote log
destination to a computer running diagnostics.
Display
Shows the temperature of the display, sets the intensity of
the backlight, and enables/disables the screen saver.
File Management
Copies or deletes application files or font files from a
storage location.
Font Linking
Links a font file to a base font loaded on the terminal.
Input Devices
Configures settings for the keypad, touch screen, or
attached keyboard and mouse.
Networks and Communications
Configures network connections and communication
settings specific to the application (DHPlus, DH-485,
remote I/O, ControlNet, DeviceNet, serial).
Print Setup
Configures settings for printing displays, alarm messages,
and diagnostics messages generated by the application.
Startup Options
Specifies whether the terminal starts up in configure or
run mode. Also lets you enable/disable tests to run on the
terminal at startup.
System Event Log
Displays a list of system events currently logged by the
terminal.
System Information
Displays power, temperature, battery and memory details
for the terminal. Also shows the firmware number for
RSView ME software and technical support information.
Time/Date/Regional Settings
Sets the date, time, language, and numeric format used by
the terminal and applications.
Configuration Mode
63
Follow these steps to access terminal settings and select a function.
1. Select Terminal Settings from the main screen.
Diagnostics Setup
Display
File Management
Font Linking
Input Devices
Networks and Communications
Print Setup
Startup Options
System Event Log
System Information
Time/Date/Regional Settings
Moves highlight up.
Moves highlight down.
Selects highlighted item
and opens screen.
Returns to previous
screen.
2. Highlight an option by using the up and down cursor buttons.
• On touch screen terminals, press the buttons.
• On keypad terminals, press a key on the keypad or the
corresponding function key.
3. Press the Enter key to access the highlighted function.
Configure Communications
You configure communication for your application and controller by
using RSLinx Enterprise software.
• Access KEPServer Serial Port ID’s.
• Edit or view the driver settings for the communication protocol
used by your .MER application.
• Edit the device address of the controller on the network.
KEPServer Serial Port ID’s
To access the KEPServer Serial Port ID’s screen, you must have
KEPServer Enterprise installed on your terminal. Otherwise, you will
get an error message when accessing this screen. If you plan on using
KEPServer Enterprise and serial communication, you must specify
which COM port to use.
To access the KEPServer Serial Port ID screen, select Terminal
Settings>Networks and Communications>KEPServer Serial Port ID’s.
Publication 2711P-UM001F-EN-P - March 2007
64
Configuration Mode
Configure Communication Properties
Follow these steps to configure driver settings for the communication
protocol used by your application.
1. Select Terminal Settings>Networks and Communications>RSLinx
Enterprise Communications.
You see a tree view of installed communication cards and
network configurations.
Ethernet Driver
Has no properties to edit.
Communication Driver
AB_ETH-1
<No Devices>
Serial-DF1
<No Devices>
2. Select the communication card installed on your terminal.
3. Press the Edit Driver button to view the current properties for
the communication driver.
4. Select the property you want to modify, then press the Edit
button.
5. Modify the setting and then press the Enter button.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
65
You return to the previous screen with the newly entered data.
DHPlus Properties
Field
Description
Valid Values
Jumper ID
Identifies the communication card if multiple
cards are installed on terminal.
0…3
Station Number
The unique address of the terminal on the
DHPlus network.
0…77 (octal)
Baud Rate
The communication rate of the DHPlus
network.
57,600 (default)
115,200
230,400
Field
Description
Valid Values
Jumper ID
Identifies the communication card if multiple
cards are installed on terminal.
0…3
Station Number
The unique station number of the terminal on
the DH-485 network.
0…31 (decimal)
Baud Rate
The communication rate of the DH-485
network.
9600
19,200
DH-485 Properties
MaxStationNumber The maximum station number on the DH-485
network. The value must be greater than or
equal to the Station Number.
0…31 (decimal)
Remote I/O Properties
Field
Description
Valid Values
Jumper ID
Identifies the communication card if multiple
cards are installed on terminal.
0…3
Baud Rate
The communication rate of the remote I/O
network.
57,600 (default)
115,200
230,400
ControlNet Properties
Field
Description
Valid Values
Device ID
Unique address of the PanelView Plus
terminal on the ControlNet network.
1…99
DeviceNet Properties
Field
Description
Valid Values
MacID
Unique address of the terminal on the
DeviceNet network.
0…63
Baud Rate
The communication rate at which the
DeviceNet driver communicates.
125 Kbps (default)
250 Kbps
500 Kbps
Publication 2711P-UM001F-EN-P - March 2007
66
Configuration Mode
Serial Properties
Publication 2711P-UM001F-EN-P - March 2007
Field
Description
Valid Values
Device
The serial device your terminal is connected
to.
PLC_CH0
KF2
SLC_CH0
KF3
KFC
KFC15
AC_CH0
Error Check
Type of error checking used. Error checking is
automatically configured if Use Auto Config
is set to Yes.
BCC, CRC
Parity
Type of parity used. The parity is
automatically configured if Use Auto Config
is set to Yes.
None, Odd, Even
Stop Bits
Number of stop bits used.
1 or 2
Ack Timeout
Ack/Poll timeout value in ms.
20…60,000 ms
Max Retries
Maximum number of retries before the serial
driver fails.
0…255
Station
Station number based on a specific device.
PLC_CH0
KF2
SLC_CH0
KF3
KFC
KFC15
AC_CH0
Baud Rate
Data rate at which serial driver
communicates. The baud rate is
automatically configured if Use Auto Config
is set to Yes.
110
300
600
1200
4800
9600
19,200
38,400
115,200
Use Auto Config
Automatically or manually configures the
baud rate, parity, and error checking
parameters.
Yes (auto configure)
No (manual configure)
Com Port
Communication port used on the terminal.
1 (COM1)
2 (COM2)
0…77 (octal)
0…77 (octal)
0…31
0…31
1…99
1…99
0…255
Configuration Mode
67
Configure the Controller Address
Follow these steps to edit the device address of the logic controller.
1. From the RSLinx Configuration screen, select a device node.
2. Press the Edit Device button to view the device name and
current address of the logic controller.
3. Press the Device Address button to modify the address.
The input panel opens with the current address.
4. Use the Input Panel to modify the address and then press the
Enter button.
You return to the previous screen with the new address.
5. Press OK.
IMPORTANT
Modified settings do not take effect until the terminal is
restarted.
Publication 2711P-UM001F-EN-P - March 2007
68
Configuration Mode
Configure Network
Information
You can configure network information for your terminal.
• Device name to identify terminal on network
• IP address of terminal on network
• Username and password to access network resources
Define a Device Name for the Terminal
You can configure a device name and description to identify your
your terminal on the network.
Follow these steps to enter a device name and description for your
terminal.
1. Select Terminal Settings>Networks and
Communications>Network Connections>Device Name.
2. Press the Device Name button to enter or edit the device name.
3. Press the Device Description button to enter or edit the
description for the device.
Field
Description
Valid Values
Device Name (1)
Name that identifies the terminal to
other computers on the network.
1…15 characters
A leading character in the
range of a through z or
A through Z.
Remaining characters in the
range of a through z,
A through Z, 0…9,
or - (hyphen)
Device Description
Provides a description of the
terminal.
50 characters max
(1)
Check with your network administrator to determine a valid device name.
4. Press OK.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
69
Define an Ethernet IP Address
Some networks automatically assign IP addresses to Ethernet devices
if DHCP is enabled. If DHCP is not enabled, you can manually enter
an IP address for the terminal.
Follow these steps to view or enter an IP address for your terminal.
1. Select Terminal Settings>Network and
Communications>Network Connections>Network Adapters.
E100CE1:Built-in Ethernet Controller
2. Press the IP Address button to view or modify the IP address.
3. Press the DHCP button to enable or disable DHCP assignment of
addresses.
4. Press the IP address, Subnet Mask, and Gateway buttons, then
enter the appropriate information.
5. Press OK when done.
Publication 2711P-UM001F-EN-P - March 2007
70
Configuration Mode
Field
Description
Valid Values
Use DHCP
Enables or disables Dynamic Host
Configuration Protocol (DHCP) settings. DHCP
automatically allocates network devices and
configurations to newly attached devices on
the network.
Yes (default)
No
If DHCP is set to Yes, the terminal is
automatically assigned an IP address, Subnet
Mask, and Gateway. The fields are disabled.
If DHCP is set to No, you can enter the IP
address, Subnet Mask, and Gateway
address.
Publication 2711P-UM001F-EN-P - March 2007
IP Address
A unique address identifying the terminal on
the Ethernet network.
xxx.xxx.xxx.xxx
000.000.000.000 (default)
Range of values for the first
set of decimal numbers is
1…255 unless all fields are
set to 000. The range of values
for the last three sets of
decimal numbers is 0…255.
Subnet Mask
Address must be identical to the server
subnet mask.
xxx.xxx.xxx.xxx
Gateway
Optional Gateway address.
xxx.xxx.xxx.xxx
Mac ID
Read-only field.
Configuration Mode
71
Define Name Server Addresses
You can define name server addresses for the EtherNet/IP network
adapter. These addresses are automatically assigned if DHCP is
enabled for the network adapter.
Follow these steps define name server address.
1. Select Terminal Settings>Network and
Communications>Network Connections>Network Adapters.
2. Press a button to enter a name server address.
Field
Description
Valid Values
Primary DNS
The address of the primary DNS resolver.
xxx.xxx.xxx.xxx
Secondary DNS
The address of the secondary DNS resolver.
xxx.xxx.xxx.xxx
Primary WINS
The address of the primary WINS resolver.
xxx.xxx.xxx.xxx
Secondary WINS
The address of the secondary WINS resolver. xxx.xxx.xxx.xxx
3. Press OK when done.
Publication 2711P-UM001F-EN-P - March 2007
72
Configuration Mode
Authorize Terminal to Access Network Resources
The terminal can access network resources with proper identification.
A user name, password, and domain must be provided by your
network administrator.
1. Select Terminal Settings>Network and
Communications>Network Connections>Network Identification.
2. Press the user name, password and domain buttons and enter
the information provided by your network administrator.
Field
Description
Valid Values
User Name
Identifies the user to the network.
70 characters max
Password
Characters that gain access to network
along with the user name.
No character limitation
Domain Name
Provided by network administrator.
15 characters max
3. Press OK when done.
Configure Diagnostics
You can configure diagnostics for the current computer. To access the
diagnostic screen, select Terminal Settings>Diagnostic Setup from the
main screen. The screen shows a tree view of diagnostic nodes.
To access the Remote
Log Setup or Message
Routing, select the node
and then the Edit button.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
73
Remote Log Destination
The Remote Log Destination forwards messages that it receives to a
Windows 2000/XP computer running diagnostics. The location is
determined by the IP address and port number.
Field
Description
Valid Values
Address
Address of the remote Windows 2000/XP
computer.
xxx.xxx.xxx.xxx
Port
The port used to communicate with the
remote Windows 2000/XP computer.
4445 (default)
Message Routing
The Message Routing screen lets you access these screens:
• Remote Log
• RSView Diagnostics List
Each of the above screens shows a list of messages that can be sent to
that destination. The list shows the On/Off status of each message
type. Use the On/Off button to turn a message type on or off. A
message type is enabled if it has a checked box.
Publication 2711P-UM001F-EN-P - March 2007
74
Configuration Mode
Manage Files on the
Terminal
The terminal provides operations for managing files that are stored on
the terminal.
• Delete application .MER files, font files, or log files that reside in
a storage location on the terminal.
• Copy application .MER files or font files from one storage
location to another.
Delete an Application File or a Font File
The procedure for deleting an application file or a font file from the
terminal is the same except for the type of file you are deleting.
1. Select Terminal Settings>File Management>Delete Files>Delete
Applications or Delete Fonts.
2. Press the Source button to choose the storage location of the
application or font file you want to delete.
• Internal Storage - the internal CompactFlash in the terminal.
• External Storage 1 - the external CompactFlash card loaded in
the card slot of the terminal.
• External Storage 2 - for future use.
3. Select a file from the list.
4. Press the Delete button.
5. Select Yes or Not when asked if you want to delete the selected
application or font file from the storage location.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
75
Delete Log Files from Terminal
You can delete log files, alarm history files, and alarm status files from
the System Default location on the terminal.
1. Select Terminal Settings>File Management>Delete Files>Delete
Log Files.
You are asked to confirm the deletion of the files.
Do you want to delete all of the RSView ME Station Log Files?
2. Select Yes or No.
Log files not located in the System Default location will not be
deleted.
Copy an Application File or Font File
The procedure for copying an application .MER file or a font file from
one storage location on the terminal to another is the same.
1. Select Terminal Settings>File Management>Copy Files>Copy
Applications or Copy Fonts.
List of files stored
in CompactFlash
of terminal.
2. Press the Source button to choose the location of the application
or font file you want to copy.
• Internal Storage - the internal CompactFlash in the terminal.
• External Storage 1 - the external CompactFlash card loaded in
the card slot of the terminal.
• External Storage 2 - for future use.
3. Select a file from the storage location.
Publication 2711P-UM001F-EN-P - March 2007
76
Configuration Mode
4. Press the Destination button on the same screen.
5. Press the Destination button to choose the storage location
where you want to copy the application or font file.
The destination must be different than the source location.
• Internal Storage - the internal CompactFlash in the terminal.
• External Storage 1 - the external CompactFlash card loaded in
the card slot of the terminal.
• External Storage 2 - for future use.
6. Press the Copy button to copy the selected application or font
file to the selected destination.
If the file exists, you will receive a warning and will be asked if
you want to overwrite the existing application.
7. Select Yes or No.
TIP
Publication 2711P-UM001F-EN-P - March 2007
RSView ME software looks for .MER files in the
\Rockwell Software\RSViewME\Runtime folder and font
files in the \Rockwell Software\RSViewME\Fonts\ folder.
Configuration Mode
Modify Display Settings
77
You can access and modify these display settings for your terminal:
• View display temperature
• Adjust display contrast
• Adjust display intensity
• Configure the screen saver
• Enable or disable the screen cursor
View the Display Temperature
To view the current temperature of the display, select Terminal
Settings>Display>Display Temperature.
The PanelView Plus 600 to 1500 terminals have a cold-cathode
fluorescent lamp (CCFL) backlight. This backlight requires
temperature control when the internal temperature of the product is
below 10 °C (50 °F) or above 60 °C (140 °F). The terminal monitors
low and high temperature conditions.
• If the internal temperature of the product is below 10 °C (50 °F),
the backlight is set to overdrive or the full-rated current setting
for at least five minutes.
• If the internal temperature is at or above 60 °C (50 °F), the
backlight is set to underdrive; 40% or less of full brightness. This
reduces heat generation from the backlight.
Temperature monitoring begins when the terminal powers on, or
when the backlight turns on, for example, exiting Screen Saver mode.
The temperature control only affects display intensity; it does not
restrict the use or operation of the terminal.
When a low or high temperature condition is detected, an error is sent
to the system event log. If the temperature control is not functioning,
a noncritical error is sent to the system event log but the terminal
continues to operate normally.
TIP
The CCFL backlight temperature control takes precedence over
the application Backlight Settings.
Publication 2711P-UM001F-EN-P - March 2007
78
Configuration Mode
Adjust the Display Contrast
You can view or modify the display contrast for PanelView 400 and
600 grayscale terminals. Displays are shipped with the contrast level
set at 50%, which is the optimum setting.
1. Select Terminal Settings>Display>Display Contrast.
2. Press the up an down cursor buttons to adjust the contrast.
The current contrast level is shown as a percentage. The change
is not permanent until you press OK.
3. Press OK when done.
Adjust the Display Intensity
You can view or modify the intensity of the terminal backlight. You
can use the default intensity of 100% or you can set the intensity for
runtime operations.
1. Select Terminal Settings>Display>Display Intensity.
2. Press the Startup Intensity button to switch between the Default
intensity and the Runtime intensity.
• If you choose Runtime, the startup screens will use the
runtime intensity.
• If you choose Default, the startup screens will use the default
setting of 100%
3. Increase or decrease the intensity for runtime operations, by
pressing the up or down arrow keys.
Intensity changes are not permanent until you press OK.
4. Press OK when done.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
79
Configure the Screen Saver
The terminal screen saver activates after an idle period using a specific
intensity. You can adjust the idle timeout and intensity, disable the
screen saver, and enable or disable the screen saver bitmap.
1. Select Terminal Settings>Display>Screen Saver.
2. Press the Screen Saver button to select an idle timeout for
activating the screen saver.
To disable the screen saver, select the Disabled option.
3. Increase or decrease the brightness intensity of the screen saver
by pressing the up and down cursor buttons.
4. Press the Advanced Settings button to access the bitmap option.
• Select the Screen Saver Image button to enable or disable the
screen saver bitmap.
• Press OK to return to the previous.
5. Press OK to exit and return to the terminal settings.
Publication 2711P-UM001F-EN-P - March 2007
80
Configuration Mode
Enable or Disable the Screen Cursor
The terminal has a screen cursor that you can enable or disable.
1. Select Terminal Settings>Display>Cursor.
2. Press the Enable Cursor button to enable or disable the cursor.
3. Press OK to exit and return to Terminal Settings.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
Font Linking
81
Font linking lets you run a translated application on the terminal by
linking a font file to the base font (for example, linking a Chinese font
file to the base font Arial).
Terminal Settings
For more details on preinstalled terminal fonts and additional fonts
available for downloading, see Appendix C.
Font Linking
Select Base Font
Arial
Courier New
Tahoma
Times New Roman
List of fonts loaded on
the terminal.
Show Links
[F1]
Shows all fonts loaded on the terminal except the
base font. Select the name of the font you are
linking to the base font. Select the Add Fonts button
to link the font file for the selected font to the base
font. You will return to the Linked Fonts screen.
Close
[F8]
Linked Font
Add Linked Font
Courier New
MS Mincho
Tahoma
Times New Roman
Shows the location and name of the
font that is linked to the base font
used by the terminal. If a file is not
linked, box will be empty.
Add Fonts
[F1]
Close
[F8]
Base font = Arial
Link:
MS Mincho
External storage 1\MSMINCHO.TTC
Delete Link
[F1]
Deletes linked
font file (if any).
Edit Link
[F2]
Close
[F8]
Edits the link by letting you add the linked
file to a font loaded on the terminal.
Publication 2711P-UM001F-EN-P - March 2007
82
Configuration Mode
Configure Keypad,
Keyboard, or Mouse
You can configure input devices used with your terminal, including
the keyboard, keypad, mouse, and attached keyboard.
Configure Keyboard Settings
You can adjust settings for the keys on the terminal keypad or for keys
on an attached keyboard.
1. Select Terminal Settings>Input Devices>Keyboard.
2. Press the Repeat Rate button to specify the number of times a
key is repeated per second when you hold a key down.
Valid values for the keypad are 0 and 2…30. The keyboard is
device dependent but typical values are the same.
3. Press the Repeat Delay button to select the amount of time that
elapses per second before a key is repeated.
Values are device dependent. Unsupported values are dimmed.
4. Press OK when done.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
83
Configure Keypad Settings for the Terminal
You can restrict multiple or simultaneous key presses on the keypad
of your terminal.
1. Select Terminal Settings>Input Devices>Keypad.
2. Press the Single Key Mode button to select a key option.
• If Enabled, any programmable key that is pressed inhibits all
keys until the programmable key is pressed again. This
includes the Alt, Ctrl, Shift keys.
• If Enabled with Abort, any secondary key press will terminate
the initial key press immediately.
• If Disabled, there are no restrictions on key presses. This is
the default.
IMPORTANT
The keypad cannot produce Home, End, Page Up or Page
Down when Single Key mode is enabled.
3. Press the Hold Off Time button to enter the length of time, in
seconds, to ignore multiple presses of the same key.
4. Press OK when done.
Configure the Sensitivity of the Mouse
You can set and test the sensitivity for both the speed and physical
distance between mouse clicks. The process is identical to setting the
double-tap sensitivity for the touch screen.
To set the mouse sensitivity, select Terminal Settings>Input
Devices>Mouse.
Publication 2711P-UM001F-EN-P - March 2007
84
Configuration Mode
Configure the Touch Screen
You can configure these operations for terminals with a touch screen:
• Calibrate the touch screen
• Enable or disable Cursor
• Set the double-tap sensitivity
Calibrate the Touch-screen
IMPORTANT
Use a plastic stylus device with a minimum tip radius of 1 mm
(0.040 in.) to prevent damage to the touch screen.
Follow these steps to calibrate the touch screen.
1. Select Terminal Settings>Input Devices>Touch
Screen>Calibration.
The screen for calibrating the touch screen appears.
Carefully press and briefly hold stylus on the center of the target.
Repeat at as the target moves around the screen.
2. Touch the center of the target (+) each of the four times it
appears on the screen.
When the calibration is complete, you will see this message.
Tap the screen to register saved data. Wait for 30 seconds to
cancel saved data and keep the current settings.
3. Tap the screen to save the data or wait 30 seconds to cancel the
saved data, retaining the current settings.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
85
Enable or Disable the Cursor on Touch Screens
You can enable or disable the cursor on terminals with a touch screen.
Disabling the cursor will not disable the mouse.
1. Select Terminal Settings>Input Devices>Touch Screen>Cursor.
2. Press the Enable Cursor button to enable or disable the cursor.
3. Press OK.
Publication 2711P-UM001F-EN-P - March 2007
86
Configuration Mode
Set the Double-tap Sensitivity
You can set and test the sensitivity for both the speed and physical
distance between touch-screen presses. The process is identical to
setting the double-tap sensitivity for the mouse.
1. Select Terminal Settings>Input Devices>Touch
Screen>Double-tap Sensitivity.
2. Double-tap the Set button to set the sensitivity of touch-screen
presses.
3. Double-tap the Test button to test the sensitivity of touch-screen
presses.
If you double-tap the test button with the time set using the Set
button, the Test button will reverse its foreground and
background colors.
4. Press OK when done.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
Configure Print Options
87
You can configure settings for printing displays, alarm messages, or
diagnostic messages from RSView Machine Edition .MER applications.
The general setup for printing displays and messages is the same,
however, the advanced settings are different.
1. Select a Terminal Settings>Networks and Communications>Print
Setup> option.
• Displays
• Alarms
• Diagnostic Messages
2. Update properties by selecting the appropriate button and
changing the value, if necessary.
Field
Description
Valid Values
PCL Printer
Type of printer to use.
Laser (default)
Inkjet
Port
Port to use for printing displays, alarm
messages, and diagnostic messages.
Network (default)
USB
Network Path
Network path of printer to use if the Port
selection is Network.
519 characters max
Advanced Settings
Accesses additional settings.
3. Press the Advanced button to access additional settings.
The advanced settings for printing displays are:
• print orientation (portrait or landscape).
• draft mode (enable or disable).
Publication 2711P-UM001F-EN-P - March 2007
88
Configuration Mode
• The advanced settings for printing diagnostic and alarm
messages determines when to print messages that are sent to
the network or USB port.
Print Messages After
Default Value
Example
Specified number of messages
60 messages
When the queue has 60 messages, the messages are printed
regardless of how long they have been in the queue.
You can change the number of messages.
500 messages or timeout period,
whichever is first
168 hours (7 days)
If the queue has 350 messages after 168 hours, the 350
messages are printed.
You can change the timeout period.
Specified number of messages or timeout
period, whichever is first.
60 messages
168 hours (7 days)
If the queue has 60 messages after 24 hours, then the 60
messages are printed.
You can change the number of messages and the timeout
period.
For example, the number of messages is set to 75 and the
timeout period is set to 48 hours.
• If the queue has 75 messages after 24 hours, then the 75
messages are printed before the set timeout of 48 hours.
• If the queue has 15 messages after 48 hours, the 15
messages are printed after the set timeout period.
4. Press OK when done.
5. Press OK to return to Terminal Settings.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
Configure Startup Options
89
RSView ME Station software starts based on shortcuts in the Windows
startup folder and whether an application is loaded. You can modify
the action the terminal takes on startup.
• Disable RSView ME Station software
• Go to RSView Configure mode
• Run the current application
Disable RSView ME Station Software on Startup
1. Select Terminal Settings>Startup Options>RSView ME Station
Startup.
2. Press the On Startup button until Do not start RSView ME is
selected.
3. Press OK.
Publication 2711P-UM001F-EN-P - March 2007
90
Configuration Mode
Enter Configuration Mode on Startup
Follow these steps to enter Configuration mode on startup.
1. Select Terminal Settings>Startup Options>RSView ME Station
Startup.
2. Press the On Startup button to select Go to Configuration Mode.
3. Press the Configuration Mode Options button.
4. Press the Load Current Application button to specify whether
you want to load the current application on startup.
5. Press the Replace RSLinx Communications button to specify
whether to use the communication configuration of the current
application or the terminal on startup.
• Select No to use the RSLinx configuration of the terminal.
• Select Yes to use the configuration of the application. The
terminal configuration is replaced with the application
settings. Any changes to device addresses or driver properties
in RSLinx communication will be lost.
6. Press OK to return to the previous screen.
7. Press OK to return to Terminal Settings.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
91
Run the Loaded Application on Startup
Follow these steps to run the loaded application on startup.
1. Select Terminal Settings>Startup Options>RSView ME Station
Startup.
2. Press the On Startup button to select Run Current Application.
If an application is not loaded, the options are disabled.
3. Press the Replace RSLinx Communications button to specify
what configuration settings to use when running the application.
• Select No to use the RSLinx configuration of the terminal.
• Select Yes to use the configuration of the application. The
terminal configuration is replaced with the application
settings. Any changes to device addresses or driver properties
in RSLinx communication will be lost.
4. Press the Delete Log Files to specify what action to take with
the log files on startup.
• Select Yes to delete all log files (data, alarm history, alarm
status) generated by the terminal before running application.
The files are deleted from the system default location.
• Select No to retain all log files.
5. Press OK twice to return to Terminal Settings.
Publication 2711P-UM001F-EN-P - March 2007
92
Configuration Mode
Startup Shortcuts for PanelView Plus CE Devices
On PanelView Plus CE devices, RSView ME Station software starts
based on shortcuts in the Windows startup folder and whether an
application is loaded. RSView ME Station software can start:
• without loading or running an .MER application.
• automatically loading an .MER application.
• automatically loading and running an .MER application.
Start without Loading or Running .MER Application
To start RSView ME runtime software without loading or running a
CompactFlash application, do one of the following:
• Open the RSView ME Station icon from the desktop.
• Select RSView ME Station from the Start menu.
Programs>Rockwell Software>RSView ME Station
• Type MERuntime.exe and its path in the Run dialog of the
Windows Start menu.
Path to MERuntime.exe
If the path to RSView ME runtime contains spaces, you must
enclose the path in double quotes.
Example:
"Storage Card\Rockwell\Software\RSViewME\MERuntime.exe"
If you copy the RSView ME Station shortcut from the desktop to the
Windows Startup folder (\Storage Card\Windows\Startup), RSView
ME Station software will automatically run on startup.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
93
Start RSView ME Station Software and Load .MER Application
To start RSView ME Station software and automatically load an .MER
application, type the appropriate shortcut path in the Run dialog on
the Windows Start menu.
Path to MERuntime.exe, followed by a space, followed by the
path to the .MER
If the path to RSView ME runtime or the path to the application
contains spaces, you must enclose the path in double quotes.
Example:
"Storage Card\Rockwell\Software\RSViewME\MERuntime.exe" "Storage Card\Rockwell\Software\RSViewME\Runtime\MYAPP.MER"
If you place a shortcut to the .MER application into the Windows
Startup (\Storage Card\Windows\Startup) folder, the ME Runtime will
automatically start and load the .MER application on terminal startup.
If the application specified in the Run dialog or the Startup folder does
not exist or is corrupted, the main RSView ME Configuration Mode
screen will open.
Start RSView ME Station Station and Run .MER Application
To start RSView ME Station software and automatically run an .MER
application:
• in RSView Studio software, select Tools>Transfer Utility and
select Run application when download completes on the
Download tab.
• type the appropriate shortcut path in the Run dialog on the
Windows Start menu.
Path to MERuntime.exe, followed by a space, followed by the
path to the .MER, followed by /r
If the path to RSView ME runtime or the path to the application
contains spaces, you must enclose the path in double quotes.
Example:
"Storage Card\Rockwell\Software\RSViewME\MERuntime.exe" "Storage Card\Rockwell\Software\RSViewME\Runtime\MYAPP.MER" /r
If you place a shortcut with the above command line in the Windows
Startup folder (\Storage Card\Windows\Startup), the ME Runtime will
start and automatically run the .MER application.
If the application specified in the Run dialog or the Startup folder does
not exist or is corrupted, the main RSView ME Configuration Mode
screen will open and display the following message:
Unable to load application
Publication 2711P-UM001F-EN-P - March 2007
94
Configuration Mode
Other Shortcut Paths for RSView ME Station Software
IMPORTANT
If the path to RSView ME software or the path to the
application contains spaces, you must enclose the path in
double quotes.
• To run the .MER application and delete its log files without
replacing the terminal’s communication configuration with that
of the applications, use the following path:
Path to MERuntime.exe, followed by a space, followed by the
path to the .MER, followed by /r/d.
Example:
"Storage Card\Rockwell\Software\RSViewRSViewME\MERuntime.exe" "Storage Card\Rockwell\Software\RSViewME\Runtime\MYAPP.MER" /r/d
• To run the .MER application and replace the terminal’s
communication configuration with that of the applications
without deleting its log files, use the following path:
Path to MERuntime.exe, followed by a space, followed by the
path to the .MER, followed by /r/o
Example:
"Storage Card\Rockwell\Software\RSViewME\MERuntime.exe" "Storage Card\Rockwell\Software\RSViewME\Runtime\MYAPP.MER" /r/o
• To run the .MER application, delete its log files, and replace the
terminal’s communication configuration with that of the
applications, use the following path:
Path to MERuntime.exe, followed by a space, followed by the
path to the .MER, followed by /r/d/o
Example:
"Storage Card\Rockwell\Software\RSViewME\MERuntime.exe" "Storage Card\Rockwell\Software\RSViewME\Runtime\MYAPP.MER" /r/d/o
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
Configure Startup Tests
95
The terminal can run extended tests on startup. You can select which
test to run and also specify test settings on startup.
Select Tests to Run on Startup
Follows these steps to select which tests you want to run on startup.
1. Select Terminal Settings>Startup Options>Startup Tests.
The screen shows a list of each test that can be performed on
the terminal at startup and its current On/Off status. You can
turn any test in the list on or off by selecting the On/Off button.
The terminal will only run tests with a checked box.
2. Select the tests you want to run on startup.
• Use the up and down cursor buttons to highlight a test.
• Press the On/Off button to select a test. A checked box means
the test is selected to run. Press the button again to clear the
check box.
3. Press OK.
Publication 2711P-UM001F-EN-P - March 2007
96
Configuration Mode
Configure Startup Test Settings
Follow these steps to specify how many times to run the selected tests
on startup and to enable extended diagnostics.
IMPORTANT
Enabling extended diagnostics and setting a high repeat count
will increase the time it takes the terminal to reboot.
The tests will run each time you reset or cycle power to the
terminal until you disable extended diagnostics. Setting a low
repeat count will also decrease the startup time.
1. Select Terminal Settings>Startup Options>Startup Test Settings.
2. Press the Repeat Count button to specify the number of times,
0… 128, to run the selected tests on startup.
3. Press the Enable Extended Diagnostics button to enable or
disable extended diagnostics on startup.
• Select Yes to enable extended diagnostics.
• Select No to disable extended diagnostics.
4. Press OK.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
View and Clear the System
Event Log
97
The System Event Log screen displays a list of system events logged
by the terminal.
1. Select Terminal Settings>System Event Log.
2. Select an event and then press the More Details button to
display system event log details for that event.
3. Press the Clear All button to clear all system event logs.
4. Press OK.
Publication 2711P-UM001F-EN-P - March 2007
98
Configuration Mode
Display Terminal
Information
You can view these details for your terminal:
• Total power on time
• Processor temperature
• Battery voltage and battery state
• Amount of memory on terminal
Follow these steps to display terminal information.
1. Select Terminal Settings>System>Information>Terminal
Information.
All fields are read only except for memory allocation.
Battery State
PanelView Plus 400 and 600 Terminals
PanelView Plus 700 to 1500 Terminals
Good
Good battery condition.
Good battery condition.
Failing
Does not have a replaceable battery.
Replace the terminal.
Low battery. Replace the battery.
Bad
Does not apply.
Battery is missing or bad. Replace the
battery.
IMPORTANT
Publication 2711P-UM001F-EN-P - March 2007
For the 400 and 600 terminals, the Battery Voltage indicates the
battery state only and the Processor Temperature shows the
temperature of the display.
Configuration Mode
99
2. Press the Memory Allocation button to view or adjust the:
• amount of allocated storage or program memory.
• amount of storage or program memory in use.
3. Press the Up or Down button to increase or decrease the
allocation of storage or program memory.
Each button press changes the allocation by a value of four. If
you change the allocation for one type of memory, the other is
updated accordingly.
IMPORTANT
These settings are not retained after a power cycle. The
settings return to the defaults.
4. Press OK to return to previous screen.
5. Press OK to return to terminal settings.
Publication 2711P-UM001F-EN-P - March 2007
100
Configuration Mode
Display RSView ME Station
Information
You can display the firmware number of RSView ME Station software
and the Rockwell Automation technical support number.
1. Select Terminal Settings>System>Information>About RSView ME
Station.
x.xx.xx.x
2. Press the Technical Support button, if desired.
3. Press Close.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
Modify the Date, Time, or
Time Zone
101
You can adjust the date and time for terminal operations, or change
the time zone.
Change the Date
1. Select Terminal Settings>Time/Date/Regional Settings>Date.
The current date appears in the Year, Month, and Day fields.
2. Press the Year, Month, and Day buttons to change the values.
Field
Description
Valid Values
Year
The current year in a four-digit format.
1980…2099
Month
The current month.
1…12
Day
The current day. The day of the month is
validated based on the month.
0…31
3. Press OK when done.
Publication 2711P-UM001F-EN-P - March 2007
102
Configuration Mode
Change the Time
1. Select Terminal Settings>Time/Date/Regional Settings>Time.
The current time appears in 24-hour format in separate Hour,
Minute, and Second fields.
2. Press the Hour, Minute, and Seconds buttons to change the
values.
Field
Description
Valid Values
Hour
The current hour in 24-hour format.
0…23
Minute
The current minute in 24-hour format.
0…59
Seconds
The current second in 24-hour format.
0…59
3. Press OK when done.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
103
Change the Time Zone
You can view or modify the current time zone that is installed on the
terminal. Time zones are installed as a part of the operating system.
Changing the time zone adjusts the current time and date to match the
new time zone.
1. Select Terminal Settings>Time/Date/Regional Settings>Time
Zone.
2. Press the up and down cursor buttons to select a time zone.
Language
Default Time Zone
English
(GMT -05:00) Eastern Time (US and Canada)
French
(GMT +01:00) Brussels, Copenhagen, Madrid, Paris
German
(GMT +01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna
Japanese
(GMT +09:00) Osaka, Sapporo, Tokyo
If the selected time zone supports Daylight Savings, you can
press the Daylight Savings button.
3. Press the Daylight Savings button to enable or disable daylight
savings for the selected time zone.
Daylight Savings is set to Yes for all time zones except for
Japanese, which does not support daylight savings. Daylight
savings changes are not permanently applied until you close the
Time Zone screen.
Publication 2711P-UM001F-EN-P - March 2007
104
Configuration Mode
4. Press the Use Daylight Savings Button to select Yes or No.
5. Click OK when done.
6. Click OK to return to Terminal Settings.
Modify Regional Settings
You can adjust regional settings for a specific language installed on
the terminal, including the date, time and numeric formats.
To access regional settings, select Terminal
Settings>Time/Date/Regional Settings>Regional Settings.
The current language is shown at the bottom of the Regional Settings
screen.
Select a Language
You can select a language that is installed on the terminal. Languages
are installed as a part of the operating system.
1. Select Terminal Settings>Time/Date/Regional Settings>Regional
Settings>Language.
2. Select a language by pressing the up and down cursor keys.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
105
3. Press OK.
The selected language will appear at the bottom of the Regional
Settings screen.
Change the Decimal Separator for Numeric Formats
You can change the decimal separator used in numerics for the
current language. The default decimal separator is a period.
1. Select Terminal Settings>Time/Date/Regional Settings>Regional
Settings>Numeric Format.
The field shows the default decimal separator. The field will
accept a separator up to three characters.
2. Enter up to three characters for the new separator.
3. Click OK.
Publication 2711P-UM001F-EN-P - March 2007
106
Configuration Mode
Change the Time Format
You can change the time format for the selected language.
1. Select Terminal Settings>Time/Date/Regional Settings>Regional
Settings>Time Format.
The current time is shown using the currently selected format.
2. Press the appropriate buttons to adjust the formats.
Field
Description
Example
h:mm:ss tt (default)
h = hour, no leading zero
tt = AM or PM symbol
7:23:02 AM or 1:13:31 PM
11:43:59 AM
hh:mm:ss tt
hh = hour with leading zero
tt = AM or PM symbol
07:23:02 AM or 01:13:31 PM
11:43:59 PM
H:mm:ss
H = hour in 24-hour format, no leading zero
7:03:42 or 1:13:32
23:43:59
HH:mm:ss
HH = hour in 24-hour format with leading zero
07:03:42 or 01:13:22
23:43:59
AM Symbol
Characters to indicate AM. If the time format is
set to h:mm:ss tt or hh:mm:ss tt, you can modify
the AM symbol.
AM (default)
12 character max
PM Symbol
Characters to indicate PM. If the time format is
set to h:mm:ss tt or hh:mm:ss tt, you can modify
the PM symbol.
PM (default)
12 character max
Separator
Characters that separate fields in time format.
: (default)
3 character max
Time Format
3. Click OK.
Publication 2711P-UM001F-EN-P - March 2007
Configuration Mode
107
Change the Short Date Format
You can change the short date format for the selected language.
1. Select Terminal Settings>Time/Date/Regional Settings>Regional
Settings>Short Date Format.
The current date is shown in the selected, short date format.
Field
Short Date Formats
Example
Format
M/d/yyyy (default)
M/d/yy
MM/dd/yy
MM/dd/yyyy
yy/MM/dd
yyyy-MM-dd
dd-MMM-yy
1/2/2003
1/2/03
01/02/03
01/02/2003
03/01/02
2003-01-02
02-Jan-03
Separator
Character separator for fields in time format.
The default separator is either - or / depending
on short date format.
- or / (default)
3 character max
2. Press the Format button to select an available format.
3. Press the Separator button to change the field separator for the
date elements.
4. Click OK when done.
Publication 2711P-UM001F-EN-P - March 2007
108
Configuration Mode
Change the Long Date Format
You can change the long date format used by the selected language.
1. Select Terminal Settings>Time/Date/Regional Settings>Regional
Settings>Long Date Format.
The current date is shown in the selected long date format.
2. Press the Long Date Format button to select a date format.
Long Date Formats
Example
dddd, MMMM, dd, yyyy (default)
dddd is name of week day
MMMM is name of month
dd is two-digit day of month with leading zero
yyyy is four-digit year
Monday, January 01, 2003
MMMM dd, yyyy
MMMM is name of month
dd is two-digit day of month with leading zero
yyyy is four-digit year
January 01, 2003
dddd, dd MMMM, yyyy
dddd is name of week day
dd is two-digit day of month with leading zero
MMMM is name of month
yyyy is four-digit year
Monday, 01 January, 2003
dd MMMM, yyyy
dd is two-digit day of month with leading zero
MMMM is name of month
yyyy is four-digit year
01 January, 2003
3. Click OK when done.
Publication 2711P-UM001F-EN-P - March 2007
Chapter
5
Windows CE .NET Operating System
Chapter Objectives
This chapter applies only to PanelView Plus CE terminals and
provides information on these topics:
• Windows CE .NET architecture
• Windows CE .NET programs for PanelView Plus CE terminals
• Using Windows CE .NET operating system
• PanelView Plus CE terminal memory
• Control panel applications for configuring PanelView Plus CE
terminals
Windows CE .NET
Architecture
The Windows CE .NET operating system from Microsoft provides a
portable, scalable, real-time operating system for embedded devices.
The modular design of Windows CE .NET allows the platform builder
to include only those features required for the specific product
application. However, the Windows CE .NET operating system is still a
subset of the other Microsoft operating systems, and it runs Win32
applications.
Windows CE .NET Benefits
There are three major differences between the Windows CE .NET
operating system and other Microsoft Windows operating systems.
The Windows CE .NET operating system:
• has a small memory footprint requirement.
• runs on a wide variety of processor architectures.
• has a real-time scheduler.
The small memory footprint allows the Windows CE .NET operating
system to operate in small solid-state memory devices (8 MB typical).
In contrast, computers that run Windows operating systems require
hundreds of megabytes of storage space.
The PanelView Plus CE terminal has an x86-based processor to
maximize the consistency between Windows 2000/XP and Windows
CE .NET applications.
109
Publication 2711P-UM001F-EN-P - March 2007
110
Windows CE .NET Operating System
Compile Windows CE .NET Applications
While the Windows CE .NET operating system brings a higher level of
standardization to embedded computing devices, third-party software
applications must still be compiled and tested to run on each
Windows CE .NET device. The compilation is required to tailor the
software application to the device’s processor and unique hardware
features.
Microsoft created hardware reference models for the handheld (HPC)
and the pocket (PPC) personal computer so that third-party
applications can run on these standard platforms. There are no
hardware standards for embedded devices.
The PanelView Plus CE terminal is largely compatible with HPC and
PPC, so applications that are compiled for the x86 may run on the
PanelView Plus CE terminal.
Windows CE .NET
Programs
The PanelView Plus CE terminal includes RSView Machine Edition
software. Refer to the user manual and online help shipped with
RSView Studio software for information about using this software.
The Windows CE .NET operating system and applications are stored
on the internal CompactFlash of the PanelView Plus CE terminal for
permanent storage and can be accessed as the \Storage Card directory
in the Windows Explorer. (They are also available on the PanelView
Plus CE Accessory CD). The operating system and RSView Machine
Edition software are loaded into RAM at startup to improve response
time.
Additional programs can be installed by using ActiveSync or an
external CompactFlash card on the PanelView Plus CE terminal.
The PanelView Plus CE terminal ships with the following programs
preloaded.
Publication 2711P-UM001F-EN-P - March 2007
Application
Description
Microsoft Internet Explorer, version 5.5
Web browser
ActiveSync Support
Connects the PanelView Plus CE terminal to a
desktop computer running ActiveSync software
Control Panel
Set of configuration tools for setting up the
PanelView Plus CE terminal
Windows Explorer (Shell)
User interface to the system much like a desktop
computer
Remote Desktop Connection
Services for thin client applications included on the
PanelView Plus CE Accessory CD (formerly Terminal
Server Client)
WordPad
Text editor
PDF Viewer
Reader for Adobe Acrobat PDF files
Windows CE .NET Operating System
111
Other Windows CE .NET programs are available.
Most of these programs have been written for PPC devices, and some
may run on the PanelView Plus CE terminals. For more information on
Windows CE .NET programs, see the Knowledgebase at
http://support.automation.rockwell.com.
Install Applications
The PanelView Plus CE terminal allows field-installation of third-party
software.
Refer to Chapter 8 for details on how to use Microsoft ActiveSync
software to install and remove application programs on the PanelView
Plus CE terminal. Each application program must be compiled for the
x86 processor.
If the application program literature does not specifically identify the
PanelView Plus CE terminal as a compatible hardware platform, take
caution if trying to install and run it on the terminal. While the
program may operate on the X86 processor, there could be conflicts
with running it on the PanelView Plus CE terminal. Testing is essential.
Windows CE .NET
Operating System
The Windows CE .NET operating system provides a user interface
similar to other Microsoft Windows operating systems. This user
interface has been simplified to reduce the memory footprint.
Therefore, minor differences exist between the desktop Windows
interface and the Windows CE .NET interface.
The Windows CE .NET graphical interface simplifies interaction with
the computer. You simply select and move objects on the screen by
tapping and dragging them using your finger or stylus on the touch
screen, or using an external mouse.
TIP
If you have difficulty selecting objects using the touch screen,
run the calibration program.
The PanelView Plus CE terminal has a keypad, touch screen, or input
panel for operator input. In addition, an external keyboard or mouse
can be connected to one of the USB ports of the terminal.
Publication 2711P-UM001F-EN-P - March 2007
112
Windows CE .NET Operating System
You may find it convenient to use the following shortcuts. These
shortcuts work with the PanelView Plus CE terminal keypad, an
attached keyboard, or the input panel.
Keyboard Shortcuts
Publication 2711P-UM001F-EN-P - March 2007
Shortcut
Description
Ctrl+Esc
Opens the Windows CE .NET Start menu. Use arrow
keys to select a program and Enter to run.
Alt+Tab
Starts the Task Manager.
Enter
This key is equivalent to double-tap. In a dialog, you
can select Enter or OK.
Shift + Tab or
Selects the previous control in a dialog.
Tab or
Selects the next control in a dialog.
Ctrl+Tab
Opens the next tab in a tabbed dialog.
Esc
Closes a dialog without saving changes.
Arrow keys
Selects controls or items from a list in a dialog.
Alt
Activates menus.
Windows CE .NET Operating System
113
Start Menu and Taskbar
Use the Start menu to run programs, configure settings, and open
recently-used documents. A single-click on the Start menu button on
the bottom left of the screen brings up the menu. Subsequent clicks
select the program or item you want to open. The key sequence
Ctrl+Esc also activates the Start menu.
The taskbar across the bottom of the screen contains buttons for
programs already running, along with a status area and a Desktop
icon. You can alternately minimize and maximize an open application
by clicking on its taskbar button. Double-clicking on any icon in the
status area shows more information about that function. A single-click
on the Show Desktop button (far right side of taskbar) minimizes all
open windows and displays the PanelView Plus CE computer desktop.
You can close an application by clicking with the right mouse button
on its taskbar button and choosing Close.
Command Bar
A Windows CE.NET program has a command bar located across its
top. This command bar contains pull-down menu names and toolbar
buttons for the application.
Click on a menu name or toolbar icon to interact with the specific
program. The Help (?) button on the right side of the command bar
provides application-specific help. The Exit (X) button on the far right
side of the command bar exits the application.
Windows CE .NET command bar does not have a Minimize button.
Click the taskbar button to minimize a program window, or use the
Show Desktop button to minimize all open program windows.
Publication 2711P-UM001F-EN-P - March 2007
114
Windows CE .NET Operating System
Find Files
Select Start>Programs>Windows Explorer to locate files on the
PanelView Plus CE terminal. You can alternately double-click the My
Computer icon on the Desktop to open the Windows Explorer
program. The Windows Explorer web browser lets you browse and
manipulate the PanelView Plus CE files and folders. The Edit menu
lets you move files from one location to another by using the Copy or
Cut and Paste commands. When you create and save a new file, it is
stored in the My Documents folder unless you specify another
location.
TIP
The PanelView Plus CE file system resides in RAM and flash
memory. RAM is volatile and is not persistent after a power
cycle. Save files that must be persistent to the\Storage Card
Folder that resides on the internal CompactFlash card.
Browse Web Pages
Select Start>Programs>Internet Explorer to view Web pages. You can
alternately double-click the Internet Explorer icon on the desktop to
open the Internet Explorer program. To access pages stored on the
PanelView Plus CE terminal, use the File>Open command and select
the Browse button to locate the file. To view Internet or intranet
pages, type a URL in the Address box.
Before you can access remote Web pages, the PanelView Plus CE
terminal must be connected to a network. See the section on Network
and Dialup Connections for details on configuring the Ethernet
interface. Additional network settings such as a Proxy Server can be
configured in the Internet Explorer application by using the Options
command under the View menu.
The Microsoft Internet Explorer application is similar to the personal
computer version. It offers many of the same features of the personal
computer version, and can be used to view most Internet HTML Web
pages. Some advanced Web features may not be fully supported.
Print
Some PanelView Plus CE software applications may support printing.
To print from these applications, select the File>Print command. A PCL
compatible printer must be connected to the USB or Ethernet port on
the PanelView Plus CE terminal.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
PanelView Plus CE Memory
115
The PanelView Plus CE has the following memory areas:
• Boot ROM
• Internal CompactFlash
• Dynamic RAM
• External CompactFlash cards
• USB mass storage devices
Boot ROM
The boot ROM is used to start up the PanelView Plus CE terminal,
perform power on self tests, and load the Windows CE .NET operating
system into dynamic RAM. The boot ROM code is not user accessible.
Internal CompactFlash
The internal CompactFlash is the main storage memory in the
PanelView Plus CE terminal. The Windows CE .NET operating system
and user applications are stored in flash memory. On startup, the
operating system and any auto-start applications are transferred to
dynamic RAM, where they are executed.
The remainder of the flash memory is a FAT partition that appears as a
folder named \Storage Card in Windows CE .NET. Files stored here
are persistent (saved even after a reset or power cycle).
WARNING
Only programs and files loaded in the \Storage Card folder are
permanently saved to flash memory. All other folders or files
existing in RAM are lost when power is cycled.
Publication 2711P-UM001F-EN-P - March 2007
116
Windows CE .NET Operating System
Dynamic RAM
The RAM memory is split into two segments: Storage and Program
memory. The System application in the Control Panel has a slider
control that determines the allocation mix between Storage and
Program memory.
The Storage memory segment is a virtual RAM disk known as the
Object Store. It provides specialized storage for the Windows CE .NET
Registry, the file system, and system databases. The RAM-based
Storage memory segment is not persistent as in HPC devices, so all
files stored here must be recreated at every startup.
The Program memory segment provides traditional computer
RAM-like functions for holding application code, heaps, stacks, and
data at runtime. The PanelView Plus CE terminal loads the Windows
CE .NET operating system and any auto-start applications from flash
memory into the Program memory at powerup.
External CompactFlash Cards
External CompactFlash cards are available for the PanelView Plus CE
terminal to increase the space for storing files. When a CompactFlash
card is installed in the card slot of the PanelView Plus CE terminal, a
StorageCard2 icon is displayed under My Computer, and files on the
memory card can be manipulated by using the Windows Explorer
program.
The card slot on the PanelView Plus CE terminal supports Type 1
CompactFlash cards. The cards (2711P-RCx) are available in different
sizes.
For details on how to install/remove cards from the card slot, refer to
Chapter 6.
USB Mass Storage Devices
USB devices that comply with the USB Mass Storage Class
Specification, version 1.0, are supported to enable a wide variety of
USB-based storage devices such as hard drives, floppy disks, CD-ROM
drives and ATA flash readers. Up to 10 devices are supported,
concurrently. DVD drives are not supported.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
Control Panel Applications
117
The PanelView Plus CE terminal has user-configurable settings that are
accessed from the Windows CE .NET Control Panel applications.
These applications are similar to other Microsoft Windows operating
systems. Select Start>Settings>Control Panel to open the Control Panel
window.
Application
Description
See page
Certificates
Manages digital certificates used by some applications
for establishing trust and secure communications.
135
Date/Time
Sets the date and time on the terminal.
133
Dialing
Configures dialing rules for telephone and modem
communications.
119
Display
Configures the display and color settings, the brightness
of the backlight, and the screen saver.
126
Extended Diagnostics
Enables tests to run on the terminal at each startup and
the number of times to run each test.
128
Hardware Monitor
Views the current voltage and temperature, and system
events logged on the terminal.
130
Input Panel
Configures an input panel for entering/editing data on a
touch screen terminal.
125
Internet Options
Configures start and search pages, clears cache and
history, and specifies connection and security settings for
Internet Explorer web browser.
135
Keyboard
Configures settings for an attached keyboard.
123
Keypad
Configures settings for keys on the PanelView Plus CE
terminal.
124
Mouse
Sets the sensitivity of the mouse, if attached.
125
Network and Dial-up
Connection
Configures ActiveSync and Ethernet network connections
between your terminal and a computer.
120
Owner
Configures network and user identification information
for your terminal.
118
Password
Sets a password to protect your terminal against
unauthorized use. The password can be enabled at
system startup or when the screen saver is activated.
119
PC Connection
Selects a configured connection for connecting your
PanelView Plus CE terminal to another computer.
121
Publication 2711P-UM001F-EN-P - March 2007
118
Windows CE .NET Operating System
Application
Description
See page
Power
Provides information on the battery condition of the
terminal and other power management features.
130
Regional Settings
Sets the clock, date and language, and configures formats 133
for numbers, currency, time, date, and regional settings.
Remove Programs
Removes programs installed on your terminal.
136
Storage Manager
Displays information on terminal’s hard drive. Also
reformats and manages partitions for hard drive.
136
System
Lists system properties like memory allocation, device
information, operating system version.
131
Touch
Calibrates the touch screen, sets the sensitivity of touch
screen taps, and enables/disables the touch screen
cursor.
122
Owner
The Owner dialog provides network and user identification
information for your PanelView Plus CE terminal.
Network ID
The Network ID tab identifies the PanelView Plus CE terminal to a
network so it can gain access to network resources. A username,
password, and domain may be necessary; if so, contact your system
administrator. When done, click OK.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
119
Identification and Notes
The Identification tab defines optional user information for your
PanelView Plus CE terminal. Use the Notes tab if it is necessary to
document additional information.
Password
The Password dialog lets you define a password to protect your
terminal against unauthorized use. You can require that the defined
password be entered each time the terminal is restarted and/or when
the screen saver is activated. Select OK to activate settings.
Dialing
The Dialing dialog is a standard Windows control-panel application
that configures dialing rules for modem communication.
Publication 2711P-UM001F-EN-P - March 2007
120
Windows CE .NET Operating System
Network and Dial-up Connections
The Network and Dial-up Connections application lets you configure:
• ActiveSync connection between your PanelView Plus CE
terminal and another computer.
• Ethernet network connection.
ActiveSync Connection
For details on establishing an ActiveSync connection between your
PanelView Plus CE terminal and a computer, see chapter 8.
Serial Connect is the default, pre-configured ActiveSync connection.
Configure Ethernet Connection
Follow these steps to configure an Ethernet network connection.
1. Select the Network and Dial-up Connections application.
2. Click the PCI-E100CE1 icon to configure Ethernet settings.
3. On the IP address tab, select Obtain an IP address via DHCP or
Specify an IP Address
• IP addresses may be automatically assigned if DHCP is
enabled for the Ethernet adapter.
• If you select Specify an IP Address, complete the three text
boxes with information from your network administrator.
IP Address must be
unique on the LAN.
Subnet Mask must be
identical to the server
subnet mask.
Default Gateway
is optional.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
121
4. Click OK in the title bar.
A dialog will prompt you to either remove and reinstall your
card or restart the device for the new settings to take effect.
Click OK in the notification dialog.
5. For the built-in Ethernet Controller, you must restart the
terminal.
6. Click OK to close the Network Configuration dialog.
TIP
If DHCP is enabled for the adapter, Name Server addresses may
be automatically assigned. You can specify additional WINS or
DNS addresses on the Name Servers tab.
PC Connection
The PC Connection dialog lets you select and enable a configured
connection between your PanelView Plus CE terminal and another
computer. The current connection is listed at the bottom of the tab. To
change the connection to another computer, click Change. A dialog
will open letting you select another configured computer. Click OK
when done to activate change.
WARNING
Adjusting the PC connection named Serial_Connect may result
in an inability to connect with your desktop computer via
ActiveSync software.
Publication 2711P-UM001F-EN-P - March 2007
122
Windows CE .NET Operating System
Touch
The Touch Properties dialog lets you perform the following
operations for PanelView Plus CE touch screen terminals:
• Set double-tap sensitivity
• Calibrate the touch screen
When done performing operations, remember to click OK in the title
bar to activate settings.
Double-tap Sensitivity
The Double-tap tab sets the sensitivity for both the speed and physical
distance between screen taps. Double-tap the top grid to set the
sensitivity. Double-tap the bottom grid to test the setting.
Calibration
The Calibration tab provides instructions on how to calibrate the
touch screen. You may have to do this if the terminal is not
responding to your taps. Click Recalibrate. Touch the center of the
target as it moves around the screen. When the target returns to its
initial position, the calibration is complete.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
123
Keyboard
The Keyboard dialog configures key settings for a keyboard that is
attached to the USB port of the PanelView Plus CE terminal. You can
adjust the:
• rate for repeating a key press.
• delay from the first key press to when repeating begins.
To adjust key repeat settings, check the Enable character repeat
checkbox. Adjust how often a key repeats by moving the slider
between Slow and Fast. To adjust the delay between key repeats,
move the slider between Long and Short. Tap the field at the bottom
of the dialog and then hold down a key to test the new settings.
When done performing operations, remember to click OK in the title
bar to activate settings.
Publication 2711P-UM001F-EN-P - March 2007
124
Windows CE .NET Operating System
Keypad
Use the Keypad dialog to:
• configure key settings for keys on the PanelView Plus CE
terminal.
• adjust the rate for repeating a key press and the delay from the
first key press to when repeating begins
• enable/disable multi-key lockout.
When done performing operations, remember to click OK in the title
bar to activate settings.
Key Repeat
To adjust repeat settings for keys on an attached keyboard, check the
Enable character repeat checkbox. Then adjust how often a key
repeats by moving the slider between Slow and Fast. To adjust the
delay between key repeats, move the slider between Long and Short.
Tap the field at the bottom of the dialog and then hold down a key to
test the new settings.
Multi-Key/Hold-Off Lockout
The Multi-Key/Hold-Off tab restricts multiple or simultaneous key
presses on the PanelView Plus CE terminal and specifies a hold-off
delay between presses of the same key.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
125
Multi-Key Lockout
Under Multi-Key Lockout, select one of the following option:
• Enabled - any programmable key that is pressed inhibits all keys
until the programmable key is pressed again. This includes the
Alt, Ctrl, and Shift keys.
• Enabled with Abort - any secondary key press will terminate the
initial key press immediately.
• Disable - places no restrictions on key presses. Clear both
checkboxes.
IMPORTANT
The keypad cannot produce Home, End, Page Up, or Page Down
when Multi-Key Lockout is enabled.
Hold-Off Delay
If enabled, this option will ignore multiple presses of the same key for
a specified length of time. To enable this option, select the Enable
Hold-Off mode checkbox. Then adjust the delay time by moving the
slider to the left or right to increase or decrease the hold off time.
Mouse
If a mouse is attached to one of the USB ports of the PanelView Plus
CE terminal, you can set the sensitivity for both the speed and
physical distance between mouse taps. Double-tap the top grid to set
the sensitivity. Double-tap the bottom grid to test the setting. Click
OK.
Input Panel
The Input Panel dialog sets properties for the soft Keyboard input
panel. Use the Options button to select Large or Small keys, and other
soft key options. Click OK after making any changes.
Publication 2711P-UM001F-EN-P - March 2007
126
Windows CE .NET Operating System
Display
The Display dialog set the following display properties for the
PanelView Plus CE terminal.
• Background
• Appearance
• Backlight
• Screen saver
• Cursor
When done performing operations, remember to click OK in the title
bar to activate settings.
Background
The Background tab lets you select an image to use for the PanelView
Plus CE desktop and whether the image should be tiled.
Appearance
The Appearance tab let you change the color scheme of your desktop.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
127
Backlight
The Backlight tab adjusts the brightness of the terminal’s backlight. To
adjust the brightness of the terminal’s backlight, move the slider to the
left or right. To use the adjusted brightness when the terminal starts
up, select the Use Brightness during startup checkbox.
Screen Saver
The Screen Saver tab enables and disables the screen saver. To enable
the screen saver, check the checkbox and then select an idle time.
This will activate the screen saver after the terminal has been idle for
the specified time. You can also select a screen saver image. To adjust
the brightness of the screen saver, move the slider to the left or right.
To add a custom image for the screen saver, copy the bitmap (.bmp
file) to the \Storage Card folder and then use the Browse button to
select the image. You can disable the screen saver bitmap by selecting
(None) from the Image pull-down list.
Cursor
Use the Cursor tab to enable or disable the visible screen cursor.
Publication 2711P-UM001F-EN-P - March 2007
128
Windows CE .NET Operating System
Extended Diagnostics
From the Extended Diagnostics dialog, you can:
• enable/disable extended diagnostics to run on the PanelView
Plus CE terminal at each reset or power cycle.
• select specific tests to run.
• specify the number of times to repeat each test.
When done performing operations, remember to select OK in the title
bar to activate settings.
Iteration Count
From the Iteration tab, check the Enable Extended Diagnostic
checkbox to run selected tests on the PanelView Plus CE terminal at
each reset or startup. You can also specify how many times to run
each test. The tests are selected from the Tests and More Tests tab.
The selected tests will run each time the PanelView Plus CE terminal is
reset until disabled (by unchecking the Enable Extended Diagnostics
checkbox).
TIP
Enabling Extended Diagnostics and setting a high Iteration
count will increase the time it takes for the terminal to start up.
The tests will run each time you reset or cycle power to the
terminal until you disable Extended Diagnostics. Setting a low
iteration count will also decrease the start up time.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
129
Tests
The Tests and More Tests tabs show a list of tests that can be
performed on the PanelView Plus CE terminal at startup and the
on/off status of each test. The terminal will run only the test with
checked boxes. To enable a test, check the checkbox; to disable a
test, uncheck the checkbox. Click Clear All if you want to clear all
checkboxes.
Publication 2711P-UM001F-EN-P - March 2007
130
Windows CE .NET Operating System
Hardware Monitor
Use the Hardware Monitor dialog to:
• view the current battery voltage state and temperature of the
display and processor.
• view and clear all recorded events.
When done performing operations, remember to click OK in the title
bar to activate settings.
Voltages and Temperature
The Voltages and Temp tab shows both the nominal and actual
voltage of the battery in the PanelView Plus CE terminal and its
current status. The current temperature of the display and the
processor is also shown along with its status.
Event Log
The Event Log shows a list of all events that have occurred in the
system. Select the Clear Events button to clear all events from the list.
Power
The Battery tab on the Power dialog shows the status of the internal
battery in the terminal. Replace the battery in the terminal, when the
Battery State is Low or Very Low. For the PanelView Plus CE terminal,
you can ignore the other tabs.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
131
System
The System dialog provides system, device, and copyright information
for the PanelView Plus CE terminals. It also provides memory
allocations for storage and programs. If you make memory
adjustments, remember to click OK to activate settings.
General
The General tab displays system operating and computer information.
Memory
The Memory tab displays the amount of memory allocated and in use
for storage and programs. These settings are controlled by the system
at startup and can be adjusted by an application program. Normally, it
is not necessary to the change the setting unless a program reports a
need for more memory. Move the slider to the left to increase the
allocation for program memory. The memory allocations are
automatically adjusted as you move the slider.
Publication 2711P-UM001F-EN-P - March 2007
132
Windows CE .NET Operating System
Device Name
The Device Name tab defines a name and description for your
PanelView Plus CE terminal. This information identifies your CE
terminal to other computers on the Ethernet network. The name must
be unique on the network. You must change the name from the initial
default the terminal was shipped if more than one PanelView Plus CE
terminal is present on your Ethernet network.
The device name must include:
• 1…15 characters.
• a leading alpha character in the range a through z or
A through Z.
• remaining characters in the range a through z,
A through Z, 0 …9 or - (hyphen).
The device description is optional but useful if you want to further
describe a specific terminal.
PanelView Plus CE
Rockwell Automation 2711P CE
Copyrights
The Copyright tab provides copyright information for your PanelView
Plus CE terminal.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
133
Date/Time
The Date/Time dialog sets the current date and time for the selected
time zone. Changing the time zone will adjust the date and time
accordingly. Check the checkbox if Daylight Savings is in effect for the
current time zone.
The time appears according to the format set in the Regional Settings
dialog. After making adjustments, click Apply and then OK.
Regional Settings
Use the tabs on the Regional Settings dialog to select a language and
then set the format for how the time, date, and numbers appear for
the selected language.
When done performing operations, remember to click OK in the title
bar to activate settings.
Language
The Language tab selects a language that is installed on the PanelView
Plus CE terminal. Languages are installed as a part of the operating
system.
Publication 2711P-UM001F-EN-P - March 2007
134
Windows CE .NET Operating System
Time
The Time tab configures the time format for the selected language. A
sample of the current time format is shown. This sample changes as
you make adjustments. You can adjust the time format, the separator
between the time fields, and the AM/PM symbol.
Date
The Date tab configures the style of the short date format and the long
date format for the selected language. A sample of the current formats
is shown. These samples are updated as you make changes.
Number
The Number tab configures how negative and positive numbers will
appear for the selected language. The appearance of the current
formats is shown for both positive and negative numbers. These
samples are updated as you make changes.
Publication 2711P-UM001F-EN-P - March 2007
Windows CE .NET Operating System
135
Internet Options
The Internet Setting dialog provides tabs to configure parameters for
accessing and using the Internet on your PanelView Plus CE device.
Certificates
The Certificates dialog manages digital certificates used by some
applications for establishing trust and secure communications.
Certificates are signed and issued by certificate authorities and are
valid for a prescribed period of time.
Publication 2711P-UM001F-EN-P - March 2007
136
Windows CE .NET Operating System
Remove Programs
Use the Remove Programs dialog to remove installed programs from
your terminal. The dialog shows a list of programs that can be
removed. Select a program from the list, click Remove, and then OK.
Storage Manager
Use the Storage Properties dialog to display information about the
internal CompactFlash card and other storage devices such as the
external CompactFlash card and USB Mass Storage Devices. From this
dialog, you can also configure partitions and reformat the device.
WARNING
Publication 2711P-UM001F-EN-P - March 2007
Do not try to alter the internal CompactFlash storage device
that is displayed under Storage Info as DSK1: IDE Hard Disk
Drive. You may not be able to reboot the terminal if modifying
the internal CompactFlash partitions.
Chapter
6
Install and Replace Components
Chapter Objectives
This chapter shows how to install, replace, or upgrade various
components of the PanelView Plus terminals.
• Logic module
• RAM and internal CompactFlash
• Communication module
• Display module
• Battery
• Display module bezel
• Backlight
• Product ID label
• Keypad legend inserts
• External CompactFlash card
Required Tools
These tools are required to install and replace components:
• #00, #1, and #2 Phillips screwdriver
• Electrostatic Discharge (ESD) wristband
Precautions
Before installing or replacing any components, disconnect power
from the terminal. During installation, take care not to touch any of
the exposed electronic components.
WARNING
ATTENTION
Disconnect all power from the terminal before installing or
replacing any components. Failure to disconnect power may
result in electrical shock or damage to the terminal.
Be careful when touching any of the exposed electronic
components to prevent damage from electrostatic discharge
(ESD).
Work in a static free environment and wear a properly
grounded ESD wristband.
137
Publication 2711P-UM001F-EN-P - March 2007
138
Install and Replace Components
Compatibility of Terminal
Components
When assembling components of a 700 to 1500 terminal, or replacing
the internal CompactFlash in a logic module, the components must be
compatible.
To verify compatibility of the internal CompactFlash with the logic
module, you must know what version of RSView ME is running on the
terminal. For PanelView Plus CE terminals, you must also know the
operating system version.
1. Locate the green label on the back of the logic module to
determine the revision level of your terminal.
• Rev B: Contains RSView ME software, version 3.0, and
Windows CE software, version 3.0.
• Rev C: Contains RSView ME software, version 3.10, and
Windows CE software, version 4.1.
• Rev D, E: Contains RSView ME software, version 3.20, and
Windows CE software, version 4.1.
• Rev F, G, H, J, K: Contains RSView ME software, version 4.0,
and Windows CE software, version 4.1.
2. Determine the series of the internal CompactFlash and logic
module.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
139
It is important that you match the series of the internal CompactFlash
card with the correct series of the logic module for each terminal
revision. The logic module is available with or without memory
installed.
Component Compatibility for PanelView Plus Terminals
Terminal
Revision
RSView ME
Software Version
Logic Module Compatibility
Internal CompactFlash
2711P-RPx, 2711P-RP1x,
2711P-RP2x, 2711P-RP3x
2711P-RW1, 2711P-RW2,
2711P-RW3
Rev B (1)
Series A: 2711P-RPx/A
Series B: 2711P-RWx/B
3.0
Rev C
Series B: 2711P-RPx/B
Series C: 2711P-RWx/C
3.10
Series D: 2711P-RWx/D
Series E: 2711P-RWx/E
3.20
Series F: 2711P-RWx/F
Series G: 2711P-RWx/G
Series H: 2711P-RWx/H
4.0
Series D: 2711P-RWx/D
Series E: 2711P-RWx/E
3.20
Series F: 2711P-RWx/F
Series G: 2711P-RWx/G
Series H: 2711P-RWx/H
4.0
Series D: 2711P-RWx/D
Series E: 2711P-RWx/E
3.20
Series F: 2711P-RWx/F
Series G: 2711P-RWx/G
Series H: 2711P-RWx/H
4.0
Series D: 2711P-RWx/D
Series E: 2711P-RWx/E
3.20
Series F: 2711P-RWx/F
Series G: 2711P-RWx/G
Series H: 2711P-RWx/H
4.0
Rev D
Series C: 2711P-RPx/C
Series D: 2711P-RPx/D
Rev E
Rev F
Rev G
Rev H
Series D: 2711P-RPx/D
Series E: 2711P-RPxx/E
Rev K
Series F: 2711P-RPxx/F
(1)
When upgrading RSView ME software, version 3.0 to 3.10 or later, the Firmware Upgrade Kit is required.
Publication 2711P-UM001F-EN-P - March 2007
140
Install and Replace Components
Component Compatibility for PanelView Plus CE Devices
Terminal
Revision
RSView ME
Software Version
Windows
CE Version
Series B: 6189-RWx/B
3.0
3.0
Series C: 6189-RWx/C
3.10
Series D: 6189-RWx/D
Series E: 6189-RWx/E
3.20
Series F: 6189-RWx/F
Series G: 6189-RWx/G
Series H: 2711P-RWx/H
4.0
Series D: 6189-RWx/D
Series E: 6189-RWx/E
3.20
Series F: 6189-RWx/F
Series G: 6189-RWx/G
Series H: 2711P-RWx/H
4.0
Series D: 6189-RWx/D
Series E: 6189-RPxH/E
3.20
Series F: 6189-RWx/F
Series G: 6189-RWx/G
Series H: 2711P-RWx/H
4.0
Series D: 6189-RWx/D
Series E: 6189-RWx/E
3.20
Series F: 6189-RWx/F
Series G: 6189-RWx/G
Series H: 2711P-RWx/H
4.0
Series D: 6189-RWx/D
Series E: 6189-RWx/E
3.20
Series F: 6189-RWx/F
Series G: 6189-RWx/G
Series H: 2711P-RWx/H
4.0
Logic Module Compatibility
Internal CompactFlash
6189-RPx, 6189-RPRHx, 6189-RPEHx
2711P-RPx, 2711P-RPx, 2711P-RP6x, 2711P-RP7x
6189-RW2, 6189-RW3, 6189-RW4
2711P-RW6, 2711P-RW7, 2711P-RW8
Rev B(1)
Series A: 6189-RPxH/A
Rev C
Series B: 6189-RPxH/B
Rev D
Rev E
Rev F
Series C: 6189-RPxH/C
Series D: 6189-RPxH/D
Series D: 6189-RPxH/D
Series E: 6189-RPxHx/E
Rev G
Rev H
Rev J
Series E: 6189-RPxHx/E
Rev K
Series F: 2711P-RPxx/F
(1)
4.1
4.1
4.1
4.1
4.1
When upgrading RSView ME software, version 3.0 to 3.10 or later, the Firmware Upgrade Kit is recommended.
RSView ME terminals are compatible with .mer applications that are
the same or previous version. For example, RSView ME 3.20 terminals
can run .MER applications for RSView ME, versions 3.0, 3.1, and 3.2.
For PanelView CE devices, the appropriate changes are made to the
OS, from Windows CE software, version 3.0 to 4.1, when upgrading
from RSView ME software, version 3.0 to 3.10 or later.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
Install RAM or Internal
CompactFlash
141
The logic module of the 700 to 1500 terminals is available with or
without RAM and internal CompactFlash installed. If ordered as
separate components, you must install the memory before attaching
the logic module to the display module. The internal CompactFlash
contains flash memory, RSView ME software, and the operating
system for CE devices.
Follow these steps to install or replace RAM or internal CompactFlash.
1. Remove power from the terminal.
2. Place the terminal, display side down, on a flat stable surface.
3. Loosen the six captive screws that secure the logic module.
4. Carefully lift the logic module away from the terminal and turn
over to expose the circuit board.
ATTENTION
Wear a properly grounded ESD wristband before
touching any of the electronic components in the
logic module.
Skip steps 5 and 6 if not replacing RAM.
5. Locate the RAM module on the circuit board, pull the metal
retaining clips away from the module, and slide out the module.
CompactFlash Card
Retaining Screw
RAM Module
Retaining
Clips
6. Insert the new RAM module at a 45° angle and snap down.
Skip steps 7…11 if not replacing the internal CompactFlash.
7. Unscrew and remove the retaining clip that secures the internal
CompactFlash card.
8. Pull out the internal CompactFlash card.
9. Insert the new internal CompactFlash card.
10. Reattach the retaining clip.
11. Attach the logic module by aligning the two connectors on the
bottom of module with the connectors on the display module.
Publication 2711P-UM001F-EN-P - March 2007
142
Install and Replace Components
12. Push down on the logic module until firmly seated.
13. Tighten the six captive screws that secure the logic module to a
torque of 0.68 Nm (6…8 lb-in).
Install or Replace the Logic
Module
This section shows how to install and replace the logic module for 700
to 1500 terminals. If the display module and logic module are ordered
as separate components, attach the logic module to the display
module before panel installation.
The logic module is available with or without RAM and internal
CompactFlash installed. If ordered as separate components, you must
install the memory before attaching the logic module to the display
module.
Follow these steps to install a logic module.
1. Disconnect power from the terminal.
2. Set the terminal, display side down, on a clean, flat, stable
surface to prevent scratches, if the terminal is removed from
panel.
3. Position the logic module over the back of the display module
until the two connectors on the bottom of the logic module align
with the connectors on the display module.
Captive
Screw
4. Push down on the logic module until firmly seated.
5. Tighten the six captive screws that secure the logic module to
the display module to a torque of 0.68 Nm (6…8 lb-in).
Logic Module
Captive screws
on top and bottom.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
143
Before replacing the logic module, you must remove the
communication module, if attached. You will also need to remove the
Internal RAM and CompactFlash from the logic module to reuse in the
new logic module.
Follow these steps to replace a logic module.
1. Disconnect power from the terminal.
2. Disconnect all power and communication cables.
3. Set the terminal, display side down, on a clean, flat, stable
surface to prevent scratches, if the terminal is removed from
panel.
4. Remove the four screws that attach the communication module,
if attached, to the logic module and carefully lift the
communication module away from the logic module.
Communication Module
Screw
Logic Module
Captive Screw
Display Module
5. Loosen the six captive screws that secure the logic module to
the display module.
6. Carefully lift the logic module away from the back of the display
module.
ATTENTION
Wear a properly grounded ESD wristband before
touching any of the electronic components in the
logic module.
7. If reusing the memory in the new logic module:
• remove the RAM and internal CompactFlash from the logic
module.
• insert the RAM and internal CompactFlash in the new logic
module.
8. Install the new logic module.
9. Attach the communication module, if necessary.
Publication 2711P-UM001F-EN-P - March 2007
144
Install and Replace Components
Install or Replace a
Communication Module
This section shows how to install and replace a communication
module. The communication module installs over the logic module.
The communication modules are available as separate catalog
numbers for specific communication protocols.
PanelView Plus 700 to 1500 Terminals
TIP
The logic module must be attached to the display module
before you attach the communication module.
Follow these steps to install a communication module.
1. Disconnect power from the terminal.
2. Set the terminal, display side down, on a clean, flat, stable
surface to prevent scratches if the terminal is removed from
panel.
3. Remove the label covering the communication module
connector on the logic module.
Logic Module
REMOVE LABEL TO INSTALL
COMMUNICATION MODULE
4. Position the communication module over the logic module so
that the connectors on bottom of module align with connectors
on the logic module.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
145
To prevent ESD between the modules, allow the communication
module to touch the logic module before making connection.
Communication
Module
Connector
Logic Module
5. Push down on the communication module until the connectors
are firmly seated.
6. Tighten the four screws that secure the communication module
to the logic module to a torque of 0.68 Nm (6…8 lb-in).
Attached
Communication Module
Screw
Follow these steps to replace a communication module:
1. Disconnect power from the terminal.
2. Disconnect the communication cables from the module.
WARNING
Do not connect or disconnect any communication cable with
power applied to this device or any device on the network. An
electrical arc could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
3. Remove the four screws that secure the communication module
to the logic module.
4. Carefully lift the communication module away from the logic
module and set aside.
5. Install the new communication module.
Publication 2711P-UM001F-EN-P - March 2007
146
Install and Replace Components
PanelView Plus 400 and 600 Terminals
Follow these steps to install a communication module.
1. Disconnect power from the terminal.
2. Set the terminal, display side down, on a clean, flat, stable
surface.
3. Remove the label covering the connectors on the base unit of
the terminal.
REMOVE LABEL TO INSTALL
COMMUNICATION MODULE
4. Position the communication module over back of the terminal
so that the connector on bottom of communication module align
with the connector on the base unit.
Tighten this
screw first.
Captive
Screws
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
147
5. Push down on the communication module until the connector is
firmly seated.
6. Tighten the three captive screws that secure the module to the
terminal, starting with the bottom, left screw on the module.
Tighten screws to a torque of 0.34…0.45 Nm (3…4 lb-in).
Follow these steps to replace a communication module.
1. Disconnect power from the terminal.
2. Disconnect the communication cables from the module.
3. Loosen the three screws that secure the communication module
to the terminal.
4. Carefully lift the communication module away from the terminal
and set aside.
5. Install the new communication module.
Publication 2711P-UM001F-EN-P - March 2007
148
Install and Replace Components
Replace the Display
Module
This section shows how to replace the display module on 700 to 1500
terminals. It is necessary to remove the communication module from
the logic module to perform this operation.
Communication Module
Logic Module
Display
Module
Follow these steps to replace the display module.
1. Disconnect power from the terminal.
2. Remove the terminal from the panel.
3. Detach the communication module, if attached, from the logic
module by removing the four screws.
4. Loosen the six captive screws that attach the logic module to the
display module.
Logic Module
Captive screws
on top and bottom
5. Carefully lift the logic module from the terminal.
6. Set the display module aside.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
149
7. Position the new logic module over the new display module so
that the connectors align.
8. Push down on the logic module until firmly seated.
9. Tighten the six captive screws that secure the logic module to
the display module to a torque of 0.68 Nm (6…8 lb-in).
10. Attach the communication module (if necessary) and tighten the
four screws to a torque of 0.68 Nm (6…8 lb-in).
Publication 2711P-UM001F-EN-P - March 2007
150
Install and Replace Components
Replace the Battery
The 700 to 1500 terminals have a lithium battery is used by the
real-time clock and static RAM; it is not used for application backup or
retention. The clock module has a life expectancy of two years
without power.
WARNING
When you connect or disconnect the battery an electrical arc
can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
For Safety information on the handling of lithium batteries,
including handling and disposal of leaking batteries, see
Guidelines for Handling Lithium Batteries, publication AG 5-4.
Replace the battery only with the indicated catalog number.
Do not dispose of battery in a fire or incinerator. Dispose of
used batteries in accordance with local regulations.
Store batteries in a cool, dry environment. We recommend
25 °C (77 °F) with 40…60% relative humidity. You may store
batteries for up to 30 days between -45… 85 °C, (-49…185 °F)
such as during transportation. To avoid leakage, do not store
batteries above 60 °C (140 °F) for more than 30 days.
Follow these steps to replace the battery.
1. Disconnect power from the terminal.
2. Place the terminal, display side down, on a flat stable surface.
3. Detach the communication module, if attached, from the logic
module by removing the four screws.
4. Loosen the six captive screws that attach the logic module to the
display module.
Logic Module
Captive screws
on top and bottom.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
151
5. Carefully lift the logic module away from the terminal and flip
over to expose the circuit board.
ATTENTION
Wear a properly grounded ESD wristband before
touching any of the electronic components in the
logic module.
6. Locate the battery on the circuit board.
Remove battery by lifting up the
edge indicated by arrow.
7. Remove the battery by lifting up the side of the battery.
8. Insert the new battery.
9. Attach the logic module by aligning the two connectors on the
bottom of the module with the connectors on the terminal.
10. Push down on the logic module until firmly seated.
11. Tighten the six captive screws that secure the logic module to a
torque of 0.68 Nm (6…8 lb-in).
12. Attach the communication module (if necessary) and tighten the
four screws to a torque of 0.68 Nm (6…8 lb-in).
Publication 2711P-UM001F-EN-P - March 2007
152
Install and Replace Components
Replace the Bezel
It is not necessary to remove the logic module or communication
module before removing the bezel, except on the PanelView Plus 700
terminal.
Remove the Display Module Bezel
Follow these steps to remove the display module bezel on a 700 to
1500 terminal.
1. Disconnect power from the terminal.
2. Set the terminal, display side down, on a flat stable surface.
ATTENTION
Wear a properly grounded ESD wristband before
touching any of the electronic components in the
logic module.
3. On touch screen only terminals, remove the two screws that
secure the small metal plate to the back of the display module.
4. Disconnect the touch screen connector.
Plate
Touch Screen Connector
5. Remove the screws from the back of the display module.
The number of screws varies for each terminal type.
Display Module Bezel
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
153
6. Remove the sealing gasket.
7. Lift the back of the display module away from the bezel.
Work on a clean, flat, stable surface to protect the display from
debris, scratches and damage.
Display Module Bezel
8. Detach all connectors, maximum of three.
The number of connectors varies by model.
• IrDa connector, if present
• Function key connector
• Touch screen connector
9. Set the bezel aside.
Publication 2711P-UM001F-EN-P - March 2007
154
Install and Replace Components
Replace the Display Module Bezel
Follow these steps to replace the display module bezel.
1. Make sure the bezel is free of lint and marks before attaching.
2. Attach the connectors.
The number of connectors varies by model.
• IrDa connector, if present
• Function key connector
• Touch screen connector
3. Place the back of the display module over the bezel.
Be careful not to pinch any of the cables. Allow the touch screen
connector to extend out of the access opening.
4. Attach the touch screen connector.
5. Replace the sealing gasket.
6. Attach the screws that secure the display module to the bezel
and tighten to a torque of 1.35…1.58 Nm (12…14 lb-in).
7. On touch screen terminals, reattach the small metal plate to the
back of the display module using two screws and torque to
0.68 Nm (6…8 lb-in).
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
Replace the Backlight
155
This section shows how to replace the backlight for the 700, 1000,
1250, and 1500 terminals. The 1250 high-bright terminals do not have
a replaceable backlight.
Backlights for PanelView Plus 700 to 1500 Displays
Use Cat. No.
For Display
Series
# of Backlights
2711P-RL7C
700
A and B
1
C
1
A
1
B and C
1
A and B
2
C
1
B
2
2711P-RL7C2
2711P-RL10C
1000
2711P-RL10C2
2711P-RL12C
1250
2711P-RL12C2
2711P-RL15C
IMPORTANT
1500
Disposal: The backlights for these products contain mercury.
Dispose of per applicable laws.
Follow these steps to replace the backlight:
1. Disconnect power from the terminal.
2. Remove the display module bezel.
IMPORTANT
The 700 series C display is not secured by screws and is only
retained by a bracket. Use care not to drop the display once the
bezel is removed.
3. Remove the four screws that secure the display bracket for the
700 series C display.
4. Remove the four screws that secure the LCD display for all other
displays.
5. Lift the LCD display and detach the display connector from the
circuit board.
The circuit board layout may vary for each terminal model.
Publication 2711P-UM001F-EN-P - March 2007
156
Install and Replace Components
The location of the connector varies by model.
Display
Connector
6. Detach the backlight connectors from the circuit board.
The 1250 has one or two backlight connectors depending on the
series of the display. The 1500 has four backlight connectors.
Backlight
Connector
1250
1500
7. Follow these steps for the PanelView Plus 700 and 1000
displays.
a. Press the retaining tab that secures the backlight and then pull
out the backlight.
Backlight
Retaining Tab
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
157
b. Insert the new backlight.
Backlight
8. Follow these steps for the PanelView Plus 1250 and 1500
displays.
a. Remove the screws that secure the backlights and remove the
backlights.
– The two backlights for the 1250 series A and B displays are
each secured with two screws. The single backlight for the
1250 series C displays is secured with one screw.
– For the 1500 series B displays, remove the tape and then
remove the backlights.
1250
Backlights
1500
b. Insert the new backlights and then secure each with the same
screws from the previous step and torque to
0.117 Nm (1.04 lb-in).
Publication 2711P-UM001F-EN-P - March 2007
158
Install and Replace Components
9. Attach the LCD display connector to the circuit board.
Refer to step 5.
10. Attach the backlight connector to the circuit board.
Refer to step 6.
11. Secure the LCD display.
a. Attach the display bracket then secure the display in the
bracket for the 700 series C display.
b. Attach the four screws for all othe displays.
Use the following chart to tighten the screws.
Screw Size Torque
#4
0.68 Nm (6…8 lb-in)
12. Replace the display module bezel.
Remove the Product ID
Label
You can remove the label on your terminal and attach your own label.
1. Remove the Allen-Bradley label using your fingers or a tweezers.
2. Clean area with damp cloth and isopropyl alcohol.
3. Remove adhesive backing of OEM label and affix over area
where label was located.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
Replace the Keypad Legend
Inserts
159
This section shows how to replace the legend inserts in the keypad
terminals. The legend strips are available as separate catalog numbers
for each keypad terminal, except for the PanelView Plus 400 terminal,
which does not support replaceable legend strips. One side of the
legend strips have the default key legends and the other side is blank
for creating custom legends.
PanelView Plus 600 Terminal
The legend inserts for function keys F1 through F10 are accessible
from the back on the unit and can be replaced with the terminal
mounted in the enclosure.
Follow these steps to replace the F1 through F10 function key
legends.
1. From the rear of the unit, pull the legend strips out from the
slots on the lower side of the terminal.
2. Slide the new insert into the same slot until only the end tab is
visible.
600 Terminal
Publication 2711P-UM001F-EN-P - March 2007
160
Install and Replace Components
PanelView Plus 700 to 1500 Terminals
The F1-Fxx and K1-Kxx legend inserts on the PanelView Plus 700 to
1500 terminals are accessible when the display module bezel is
removed.
1. Remove power from the terminal.
2. Remove the display module bezel.
3. Pull the legend inserts out from the slots on the bezel.
4. Slide the new legend strips into the same slots until only the end
tab is visible.
5. Replace the display module bezel.
Publication 2711P-UM001F-EN-P - March 2007
Install and Replace Components
Use an External
CompactFlash Card
161
All of the terminals have a CompactFlash card slot that supports
Type 1 CompactFlash cards. These cards are available in different
memory sizes.
The orientation of the card slot on the 700 to 1500 terminals varies
depending on the series of the logic module.
CompactFlash Card Slot
Insert a CompactFlash Card
Insert the card in the CompactFlash card slot of the terminal until
firmly seated.
400 and 600 Terminals
700 to 1500 Terminals
Publication 2711P-UM001F-EN-P - March 2007
162
Install and Replace Components
Remove a CompactFlash Card
Press the Eject button on the logic module. When the button pops
out, press it again to release the card. The location of the button varies
depending on the series of the logic module.
The PanelView Plus 400 and 600 terminals do not have an eject
button. Simply secure edge of card with fingers and pull card away
from slot.
Publication 2711P-UM001F-EN-P - March 2007
Chapter
7
Terminal Connections
Chapter Objectives
This chapter provides network and device connections for the
terminals.
• Wiring and safety guidelines
• Logic controller cable charts
• Communication port isolation
• USB ports
• Serial connections on base unit
• Ethernet (onboard communications)
• DH-485/DH+/RIO communications module
• ControlNet communications module
• DeviceNet communications module
Wiring and Safety
Guidelines
Use publication NFPA 70E, Electrical Safety Requirements for
Employee Workplaces, IEC 60364 Electrical Installations in Buildings
or other applicable wiring safety requirements for the country of
installation when wiring the devices. In addition to the NFPA
guidelines.
• Route communication cables to terminal by a separate path from
incoming power.
IMPORTANT
Do not run signal wiring and power wiring in the
same conduit.
• Cross power and communication lines at right angles if they
must cross.
Communication lines can be installed in the same conduit as
low-level dc I/O lines (less than 10V).
• Shield and ground cables appropriately to avoid electromagnetic
interference (EMI).
Grounding minimizes noise from EMI and is a safety measure in
electrical installations.
For more information on grounding recommendations, refer to the
National Electrical Code published by the National Fire Protection.
163
Publication 2711P-UM001F-EN-P - March 2007
164
Terminal Connections
Logic Controller Cable
Charts
The charts provide a summary of terminal connections to controllers
and network interface modules.
Runtime Communication Cables - To Controller
PanelView Plus and PanelView Plus CE Terminals to SLC Controllers
Cables: PanelView Plus and PanelView Plus CE to SLC Controllers
Protocol
PanelView Plus Comm Port
SLC-500, 5/01, 5/02
CH1 RJ45
(DH-485)
SLC-5/03, 5/04, 5/05
CH0 (9-pin RS-232)
(DF1 or DH-485)
SLC 5/03
CH1 (RJ45)
(DH-485)
SLC 5/04
CH1 (DH+)
SLC 5/05
CH1 (ENET)
N/A
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
DF1
(any)
RS-232 (DF1) Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
DH-485
(any)
RS-232 (DH-485) Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
Use AIC+ Module
(1761-NET-AIC)
Connect to Port 1 or 2
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
Use AIC+ Module
(1761-NET-AIC)
Connect to Port 1 or 2
DH-485 Communication Port
PanelView Plus 400 and 600
2711P-xxx3xx, 2711P-RN3
1747-C10 (2 m/6 ft)
1747-C11 (0.3 m/1 ft)
1747-C20 (6 m/20 ft)
Use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
1747-C10 (2 m/6 ft)
1747-C11 (0.3 m/1 ft)
1747-C20 (6 m/20 ft)
DH-485 Communication Port
PanelView Plus 700 to 1500
2711P-xxx6xx, 2711P-RN6
1761-CBL-AS03
(3 m/10 ft)
1761-CBL-AS09
(9 m/30 ft)
Use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
1761-CBL-AS03
(3 m/10 ft)
1761-CBL-AS09
(9 m/30 ft)
ControlNet
xxx15xx
ControlNet Communication Port
PanelView Plus 400 and 600
2711P-RN15C
PanelView Plus 700 to 1500
2711P-xxx15xx, 2711P-RN15S
N/A
1747-KFC15A or
1747-SCRNR/A Module with ControlNet Cable
DeviceNet
xxx10xx
DeviceNet Communication Port
PanelView Plus 400 and 600
2711P-RN10C
PanelView Plus 700 to 1500
2711P-RN10H
N/A
Use 1747-SDN Module
with DeviceNet Cable
EtherNet/IP
(any except
xxx5xx)
EtherNet/IP Comm Port
PanelView Plus 400 to 1500
(except 2711P-xxx5xx)
Remote I/O
xxx1xx
xxx6xx
Remote I/O Communication Port
PanelView Plus 400 to 1500
2711P-xxx1xx, -xxx6xx, 2711P-RN1, 2711P-RN6
DH+
xxx6xx
xxx8xx
DH+ Communication Port
PanelView Plus 400 to 1500
2711P-xxx6xx, -xxx8xx, 2711P-RN6, 2711P-RN8
(1)
N/A
Use 1761-NET-ENI Module
with Ethernet Cable
SLC 5/02 only
Use 1747-SN with
Shielded Twinaxial Cable
(1770-CD)
N/A
N/A
2711PCBL-EX04
Ethernet
Crossover
Cable (1)
Use 1747-SN Module with Shielded Twinaxial Cable (1770-CD)
N/A
PanelView Plus EtherNet/IP direction connection to SLC 5/05 requires hub or crossover cable listed.
Publication 2711P-UM001F-EN-P - March 2007
N/A
N/A
Shielded
Twinaxial
Cable
(1770-CD)
N/A
Terminal Connections
165
PanelView Plus and PanelView Plus CE Terminals to PLC-5 and MicroLogix Controllers
Cables: PanelView Plus and PanelView Plus CE to PLC-5 and MicroLogix
Controllers
Protocol
PanelView Plus Comm Port
PLC-5, PLC-5C, PLC-5E
CH0 (25-pin RS-232)
(DF1)
MicroLogix 1500LRP
CH1 (9-pin RS-232)
(DF1 or DH-485)
MicroLogix 1000, 1200,
1500LSP
CH0 (8-pin Mini DIN)
(DF1 or DH-485)
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
(9-to-25 pin adapter required)
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
2711-NC21 (5 m/16 ft)
2711-NC22 (15 m/49 ft)
(null modem not required) (1)
DF1
(any)
RS-232 (DF1) Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
DH-485
(any)
RS-232 (DH-485) Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
N/A
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
2711-NC21 (5 m/16 ft)
2711-NC22 (15 m/49 ft)
(null modem not required) (1)
DH-485 Communication Port
PanelView Plus 400 to 1500
2711P-xxx3xx, -xxx6xx, 2711P-RN3, 2711P-RN6
N/A
N/A
Use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
ControlNet Communication Port
PanelView Plus 400 and 600
2711P-RN15C
PanelView Plus 400 to 1500
2711P-xxx15xx, 2711P-RN15S
To PLC-5C with
ControlNet Cable
N/A
N/A
DeviceNet Communication Port
PanelView Plus 400 and 600
2711P-RN10C
PanelView Plus 700 to 1500
2711P-RN10H
Use 1771-SDN Module
with DeviceNet Cable
N/A
N/A
ControlNet
xxx15xx
DeviceNet
EtherNet/IP
(any except
xx5xx)
EtherNet/IP Comm Port
PanelView Plus 400 to 1500
(except 2711P-xxx5xx)
Remote I/O
xxx1xx
xxx6xx
Remote I/O Communication Port
PanelView Plus 400 to 1500
2711P-xxx1xx, -xxx6xx, 2711P-RN1, 2711P-RN6
Shielded Twinaxial Cable
(1770-CD)
DH+
xxx6xx
xxx8xx
DH+ Communication Port
PanelView Plus 400 to 1500
2711P-xxx6xx, -xxx8xx, 2711P-RN6, 2711P-RN8
Shielded Twinaxial Cable
(1770-CD)
(1)
To PLC-5E with
Ethernet Cable
Use 1761-NET-ENI Module
with Ethernet Cable
N/A
N/A
N/A
N/A
AIC+ Module recommended for isolation purposes when PanelView and controller are not on same power supply.
Publication 2711P-UM001F-EN-P - March 2007
166
Terminal Connections
PanelView Plus and PanelView Plus CE Terminals to Logix Controllers
Cables: PanelView Plus and PanelView Plus CE to Logix Controllers
Protocol
DF1
(any)
DH-485
(any)
ControlLogix
CH0 (9-pin RS-232)
(DF1)
PanelView Plus Comm Port
CompactLogix
CH0 (9-pin RS-232)
(DF1 or DH-485)
RS-232 (DF1) Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
FlexLogix
CH0 (9-pin RS-232)
(DF1)
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
RS-232 (DH-485) Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
N/A
DH-485 Communication Port
PanelView Plus 400 -1500
2711P-xxx3xx, -xxx6xx, 2711P-RN3, 2711P-RN6
N/A
Use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
N/A
ControlNet
xxx15xx
ControlNet Communication Port
PanelView Plus 400 and 600
2711P-RN15C
PanelView Plus 700 to 1500
2711P-xxx15xx, 2711P-RN15S
Use 1756-CNB Module with
ControlNet Cable
1769-L35C
with ControlNet Cable
Use 1788-CNC or 1788-CNF Card
with ControlNet Cable
DeviceNet
DeviceNet Communication Port
PanelView Plus 400 and 600
2711P-RN10C
PanelView Plus 700 to 1500
2711P-RN10H
Use 1756-DNB Module
with DeviceNet Cable
Use 1769-SDN Module
with DeviceNet Cable
Use 1788-DNBO Module
with DeviceNet Cable
EtherNet/IP
(any except
xx5xx)
EtherNet/IP Comm Port
PanelView Plus 400 to 1500
(except 2711P-xxx5xx)
Use 1756-ENET or 1756-ENBT
Module with
Ethernet Cable
To 1769-L35E with Ethernet Cable
Use 1788-ENBT Module
with EtherNet Cable
Remote I/O
xxx1xx
xxx6xx
Remote I/O Communication Port
PanelView Plus 400 to 1500
2711P-xxx1xx, -xxx6xx, 2711P-RN1, 2711P-RN6
Use 1756-DHRIO Module
with
Shielded Twinaxial Cable
(1770-CD)
N/A
N/A
DH+
xxx6xx
xxx8xx
DH+ Communication Port
PanelView Plus 400 to 1500
2711P-xxx6xx, -xxx8xx, 2711P-RN6, 2711P-RN8
Use 1756-DHRIO Module
with
Shielded Twinaxial Cable
(1770-CD)
N/A
N/A
PanelView Plus Terminals to Communication Adapters
Cables: PanelView Plus to Communication Adapters
1761-NET-AIC
Protocol
PanelView Plus Comm Port
1747-AIC
Port 2
8-pin Mini DIN()
Port 1 (9-pin)
DF1 (any)
DH-485
(any)
(1)
RS-232 Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
RS-232 Comm Port (9-pin)
PanelView Plus 400 to 1500
2711P-RN22C
N/A
N/A
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
DH-485 Communication Port
PanelView Plus 400 and 600
2711P-xxx3xx, 2711P-RN3
1747-C10 (2 m/6ft)
1747-C11 (0.3 m/1 ft)
1747-C20 (6 m/20 ft)
N/A
DH-485 Communication Port
PanelView Plus 700 to 1500
2711P-xxx6xx, 2711P-RN6
Direct Connection to
Single AIC with
Belden 9842 Cable(1)
N/A
Use serial port on terminal with an AIC+ module for a DH-485 network solution.
Publication 2711P-UM001F-EN-P - March 2007
2711-NC21 (5 m/16 ft)
2711-NC22 (15 m/49 ft)
Port 3
(DH-485)
1761-NETDNI
or 1771-NET-ENI
N/A
1761-CBL-AP00 (5 m)
1761-CBL-PM02 (2 m)
2711-CBL-PM05 (5 m)
2711-CBL-PM10 (10 m)
2711-NC21 (5 m/16 ft)
2711-NC22 (15 m/49 ft)
N/A
1761-CBL-AS03
(3 m/10 ft)
1761-CBL-AS09
(9 m/30 ft)
to single AIC+
Direct Connection to
Single AIC+ with
Belden 9842 Cable(1)
N/A
N/A
Terminal Connections
Communication Port
Isolation
167
The PanelView Plus and PanelView Plus CE terminals contain integral
and modular (externally attached) communication ports. Some of
these ports contain electrical isolation depending on the catalog
number of the terminal or communication module.
Integral Communication Port Isolation
Communication Port
400 and 600 Terminal
700 to 1500 Terminal
RS-232
Nonisolated
Isolated
USB
Nonisolated
Nonisolated
Ethernet
Isolated
Isolated
400 and 600 Modular Communication Port Isolation
Communication Port
Module
Isolation
RS-232
2711P-RN22C
Isolated
DH-485
2711P-RN3
Nonisolated
DH+
2711P-RN8
Isolated
Remote I/O
2711P-RN1
Isolated
DeviceNet
2711P-RN10C
Isolated
ControlNet
2711P-RN15C
Isolated (1)
(1)
NAP port is nonisolated.
700 to 1500 Modular Communication Port Isolation
Communication Port
Module
Isolation
DH-485
2711P-RN6
Isolated
DH+
2711P-RN6
Isolated
Remote I/O
2711P-RN6
Isolated
DeviceNet
2711P-RN10H
Isolated
ControlNet
2711P-RN15S
Isolated
Publication 2711P-UM001F-EN-P - March 2007
168
Terminal Connections
USB Ports
The 700 to 1500 terminals have two USB ports. The 400 and 600
terminals have one USB port. The terminals support standard USB
keyboard and mouse devices (HID devices) with native device
drivers. They also support some USB printers that have Printer Control
Language (PCL) capabilities. A vendor specific Windows CE driver is
required for all other USB devices.
See Appendix B for a list of compatible USB devices.
Plug the USB device into either one of the two USB ports on the
700 to 1500 terminals.
400 and 600 USB Port
USB Connector Pinout
Pin
Signal
4
3
2
1
700 to 1500 USB Ports
4
3
2
1
4
3
2
1
1
USBVCC
2
USBD-
3
USBD+
4
USB-GND
WARNING
WARNING
Do not connect or disconnect the communication cable with
power applied to the terminal, or the serial device on the other
end of the cable. An electrical arc could cause an explosion in
hazardous location installations. Be sure that power is removed
or the area is nonhazardous before proceeding.
USB devices not powered by the USB port must be within the
same enclosure and connected to a ground system common
with the terminal, or the USB devices must be used with a USB
hub that provides galvanic isolation.
If a USB hub is connected to the terminal, an externally powered USB
hub is recommended. Before attaching devices to a USB hub, check
that the power adapter is connected and powered on.
Publication 2711P-UM001F-EN-P - March 2007
Terminal Connections
Serial Connections
169
The base-configured unit of all terminals has a multi-purpose serial
RS-232 port that supports:
• DH-485 communications through a serial connection.
• DF1 full duplex communications with controllers using direct
connections or modem connections.
• third-party point-to-point communications.
• application uploads/downloads.
• printing.
The serial port on the base-configured unit of the terminal is a 9-pin,
male, RS-232 connector. The table shows the pinout descriptions for
this port and how these pins map to the serial ports on the controllers.
Base-configured Unit 400 and 600
Base-configured Unit 700 to 1500
Serial RS-232 Port
1
6
5
9
Insert plastic tie wrap in the
hole and use as strain relief
for all attached cables.
Serial RS-232 Port
Serial Port Connector Pinout
PanelView Plus RS-232 Port
9-pin DCE
1
2
RXD
2
3
4
3
TXD
3
2
7
4
DTR
4
20
5
COM
5
7
6
DSR
6
6
7
RTS
7
4
8
CTS
8
5
9
Connector Shell
SLC
9-pin
PLC
25-pin
MicroLogix/
DNI 8-pin DIN
2
Chassis Gnd
The maximum cable length for serial communications is:
• 15.24 m (50 ft) at 19.2 Kbps
• 152 m (500 ft) at 9.6 Kbps
WARNING
Do not connect or disconnect the communication cable with
power applied to the terminal, or the serial device on the other
end of the cable. An electrical arc could cause an explosion in
hazardous location installations. Be sure that power is removed
or the area is nonhazardous before proceeding.
Publication 2711P-UM001F-EN-P - March 2007
170
Terminal Connections
Modem Connection
Wire or radio modem communications is possible between the
terminal and controller. Each modem must support full duplex
communications. Refer to your modem user manual for details on
settings and configuration.
PanelView Plus Terminal
Optical Isolator
DF1 Port
Controller
Modem
Modem
Construct a Null Modem Cable
To construct a null modem cable, refer to this pinout.
Null Modem Pinout
PanelView Plus 9-pin
9-pin
Modem
Publication 2711P-UM001F-EN-P - March 2007
PanelView Plus
9-pin
25-pin
Modem
FG (Frame Ground)
-
-
-
1
FG
TD (Transmit Data)
3
2
3
3
RD
RD (Receive Data)
2
3
2
2
TD
RTS (Request to Send)
7
8
7
5
CTS
CTS (Clear to Send)
8
7
8
4
RTS
SG (Signal Ground)
5
5
5
7
SG
DSR (Data Set Ready)
6
4
6
20
DTR
DTR (Data Terminal Ready)
4
6
4
6
DSR
Terminal Connections
171
Computer Connections
The RS-232 serial port on the base-configured unit of the terminals
supports:
• application uploads/downloads using a direct connection.
• printing.
Base-configured Unit of PanelView Plus Terminal
Computer
Available Cables
Cat. No. 2711-NC13, 5 m (16.4 ft)
Cat. No. 2711-NC14, 10 m (32.7 ft)
Cat. No. 2706-NC13, 3 m (10 ft)
25-pin to 9-pin
Adapter
(if required)
RS-232 Port
PanelView Plus Port (DCE)
9-pin male
1 NC
RXD
2
TXD
3
4 NC
COM
5
6 (pulled high to +12V)
RTS
7
CTS
8
9 NC
Computer Port (DTE)
with Handshaking
9-pin male
1 DCD
2 RXD (Data Receive)
3 TXD (Data Transmit)
4 DTR
5 COM
6 DSR
7 RTS
8 CTS
9 NC
Upload/Download Cable without Hardware Handshaking
PanelView Plus Printer Port (DCE)
9-pin male
2
3
5
RXD
TXD
COM
Computer Port (DTE)
9-pin 25-pin
2
3
3
2
5
7
Publication 2711P-UM001F-EN-P - March 2007
172
Terminal Connections
Ethernet Connections
The base-configured unit of the 700 to 1500 terminals and the network
based unit of the 400 and 600 terminals have an Ethernet port that
supports:
• EtherNet/IP communications.
• third-party Ethernet communications.
• network connections.
• application uploads/downloads.
• printing.
Ethernet Connector
The base-configured unit of the terminals has an RJ45,
10/100 Base-T connector for EtherNet/IP or Ethernet TCP/IP network
communications.
Ethernet Port
Use RS-232 serial port to
transfer applications or print.
Insert plastic tie wrap in
hole and use as strain relief
for all attached cables.
The table shows the connector pinouts.
Ethernet Connector Pinout
Pin
Pin
Looking into RJ45
Connector
1
TD+
2
TD-
3
RD+
4
NC
5
NC
6
RD-
7
NC
8
NC
1
8
Shield Connection
Pin Name
Chassis Gnd
Use point-to-point, 10/100 Base-T cables with cross over pin-outs,
such as 2711P-CBL-EX04, when connecting the Ethernet port on the
terminal directly to a logic controller’s Ethernet port or a computer
10/100 Base-T port. Use standard Ethernet cables when connecting to
a switch or hub.
Publication 2711P-UM001F-EN-P - March 2007
Terminal Connections
173
Cables
The PanelView Plus devices require category 5 twisted-pair cables.
The maximum cable length between the terminal’s Ethernet port and
a 10/100 Base-T port on an Ethernet hub (without repeaters or fiber)
is 100 m (328 ft). In industrial applications, keep the cable length to a
minimum. For additional information, refer to the EtherNet/IP Media
Planning and Installation Manual, publication ENET-IN001.
WARNING
Do not connect or disconnect any communication cable with
power applied to this device or any device on the network. An
electrical arc could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
Security Considerations
IGMP (Internet Group Management Protocol) is used for IPv4
multicast. A multicast is communication between a single sender and
multiple receivers on a network. IGMP is used to exchange
membership status data between IPv4 routers that support
multicasting and members of multicast groups. A router is an
intermediary device on a communication network that expedites
message delivery by finding the most efficient route for a message
packet within a network, or by routing packets from one subnetwork
to another. A sub-network is a separate part of an organization’s
network identified through IP addressing.
PanelView Plus terminals provide level 2 (full) support for IPv4
multicasting (IGMP version 2) as described in RFC 1112 and RFC 2236.
SNMP (Simple Network Management Protocol) is used for internal
network management and is not supported.
Ports 137 and 138 are normally open to support the NetBIOS protocol
used by Windows CE.NET similar to other Microsoft and IBM network
operating systems.
Publication 2711P-UM001F-EN-P - March 2007
174
Terminal Connections
DH-485/DH+/Remote I/O
Module
Terminals with a DH-485/DH+/Remote I/O communication module
support communication with these networks.
• DH+ networks
• DH-485 networks
• Remote I/O networks
You can communicate with only one network at one time.
The 700 to 1500 terminals support all protocols on one module. The
400 and 600 terminals require a separate module for each protocol.
The DH+, DH-485, and Remote I/O connections are different between
the modules for the 400 and 600 and 700 to 1500 terminals.
Module Connections
IMPORTANT
See your controller documentation for appropriate controller
connections.
400 and 600 Terminals
700 to 1500 Terminals
DH-485 Comm Module
Allen
Bradley
DH-485
1
2
3
4
5
6
DH+
RIO
3
2
1
Pin 8
Pin 1
1. Earth Ground
2. Shield/Drain
3. Signal Ground
4. Channel B
5. Channel A
6. Termination Resistance
Remote I/O*
DH+*
3. Clear
2. Shield/Drain
1. Blue
3. Blue
2. Shield/Drain
1. Clear
Status LED Indicator
Pin 8
Comm. Connector
Programming
Connector
1. Data_H
2. Data_L
DH-485 Module is
3. +24V DC Enable
electrically isolated
4. Power 1
from Network.
5. TX Enable
6. Shield
7. Ground
8. Power 2
DH+ Comm Module*
1 SH 2
Blue
Shield/Drain
Clear
Remote I/O (Single Rack) Comm Module*
2 SH 1
* Use a Belden 9463 twin axial or equivalent cable,
cat. no. 1770-CD.
Publication 2711P-UM001F-EN-P - March 2007
Blue
Shield/Drain
Clear
Terminal Connections
175
DH+ Status Indicator
Condition
Indication
Off
Channel is not online.
Blinking green
Device is only node on the network.
Solid green
Device is online and receiving token.
Blinking red
Duplicate node.
Solid red
Failed selftest.
DH-485 Status Indicator
Condition
Indication
Off
Channel is not online.
Blinking green
Device is only node on the network.
Solid green
Device is online and receiving token.
Blinking red
Parity error.
Solid red
Failed selftest.
Remote I/O Scanner Mode Status Indicator
Condition
Indication
Off
Channel is not online.
Blinking green
At least one but not all adapters in
the scanlist are not responding.
Solid green
All adapters in the scanlist are
responding.
Blinking red
None of the adapters in the scanlist
are responding.
Solid red
Failed selftest.
Publication 2711P-UM001F-EN-P - March 2007
176
Terminal Connections
DH-485 Network Port Wiring for 700 to 1500 Terminals
Use these instructions for wiring Belden cable. If you are using
standard Allen-Bradley cables, see the Logic Controller Cable Charts.
A daisy-chained network is recommended. We do not
recommend hybrid star/daisy chain networks as shown.
IMPORTANT
RS-485 Connector to the Communication Cable
Belden
#3106A or
#9842
Belden
#3106A or
#9842
Belden
#3106A or
#9842
Connector
Connector
Connector
Incorrect
Attach the connector to the Belden #3106A or #9842 Cable as shown.
Single Cable Connection
6
5
4
3
2
1
Orange with White Stripes
White with Orange Stripes
Shrink Tubing
Recommended
Terminal
A
B
Common
Shield
Chassis Ground
Blue (#3106A) or
Drain Wire
Blue with White Stripes (#9842)
Multiple Cable Connection
to Previous Device
to Successive Device
The table shows connections for Belden #3106A.
Belden 3106A Wire Connections
Publication 2711P-UM001F-EN-P - March 2007
For this Wire/Pair
Connect this Wire
To this Terminal
Shield/Drain
Non-jacketed
Terminal 2 - Shield
Blue
Blue
Terminal 3 - (Common)
White/Orange
White with Orange Stripe
Terminal 4 - (Data B)
Orange with White Stripe
Terminal 5 - (Data A)
Terminal Connections
177
DH-485 Connections for 400 and 600 Terminals
This section shows connections between a 400 and 600 terminal with
a DH-485 communication module and an SLC or ControlLogix
controller through the AIC+ module.
PanelView Plus 400 or 600
with DH-485 Module
AIC +
1784-CP14 Cable
1761-CBL-PM002 Cable
RS-232
To ControlLogix or SLC Controller
Publication 2711P-UM001F-EN-P - March 2007
178
Terminal Connections
DH+ Network Connections
Use the Belden 9463 twin axial or equivalent cable (cat. no. 1770-CD),
to connect a terminal to a DH+ link.
You can connect a DH+ link in two ways.
• Trunk line/drop line - from the drop line to the connector screw
terminals on the DH+ connectors of the processor
• Daisy chain - to the connector screw terminals on the DH+
connectors on the processor
Follow these guidelines when installing DH+ communication links.
• do not exceed these cable lengths:
– Trunk line-cable length: 3,048 m (10,000 ft).
– Drop-cable length: 30.4 m (100 ft).
The maximum cable length is determined by baud rate.
• Do not connect more than 64 stations on a single DH+ link.
PanelView Plus 700 to 1500 Terminals
DH+ Port on Communication Module
Belden
To Controller
Clear 3
Shield SH 2
Blue 1
Terminating Resistor
• 82 Ω terminating resistor for 230.4 Kbps
• 150 Ω terminating resistor for 57.6 Kbps
and 115.2 Kbps
PanelView Plus 400 and 600 Terminals
DH+ Port on Communication Module
Belden
To Controller
Publication 2711P-UM001F-EN-P - March 2007
Blue 3
Shield SH 2
Clear 1
Terminating Resistor
• 82 Ω terminating resistor for 230.4 Kbps
• 150 Ω terminating resistor for 57.6 Kbps
and 115.2 Kbps
Terminal Connections
179
Remote I/O Connections
Use the Belden 9463 twin axial or equivalent cable (cat. no. 1770-CD),
to connect a terminal to a Remote I/O scanner. The maximum cable
length (link distance) is determined by the baud rate.
• 2800 m (10,000 ft) for 57.6 Kbps
• 1400 m (5,000 ft) for 115.2 Kbps
• 700 m (2,500 ft) for 230.4 Kbps
See Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1. The user manual for the I/O scanner module
also provides cabling information.
PanelView Plus 400-1500
Remote I/O Port on Communication Module
Belden
To Controller
Blue 3
Shield SH 2
Clear 1
Terminating Resistor
• 82 Ω terminating resistor for 230.4 Kbps
• 150 Ω terminating resistor for 57.6 Kbps
and 115.2 Kbps
Publication 2711P-UM001F-EN-P - March 2007
180
Terminal Connections
ControlNet Module
Terminals with a ControlNet communication module support
communications and the transfer of applications between devices on a
ControlNet network.
Related Information
For more information on ControlNet products, refer to these
publications:
• NetLinx Selection Guide, publication NETS-SG001
• ControlNet Coax Media Planning and Installation Guide,
publication CNET-IN002
• ControlNet Communications for PanelView Plus and PanelView
Plus CE Terminals User Manual, publication 2711P-UM003
The Rockwell Automation website http://rockwellautomation.com
provides information and product descriptions of ControlNet
products. Under the Products and Services heading, select
Communications.
ControlNet Protocol
The terminals support Unscheduled and Scheduled messaging,
Scheduled I/O, and redundant cabling with PLC-5C and ControlLogix
controllers.
The ControlNet architecture supports multiple processors and up to 99
nodes (via taps) anywhere along the trunk cable of the network.
There is no minimum tap separation and you can access the
ControlNet network from every node (including adapters).
Compatible ControlNet Controllers
A terminal with a ControlNet Module communicates with a PLC-5C
(PCCC commands) or a ControlLogix processor (CIP protocol) using
Unscheduled messaging. The following controllers are supported:
• ControlLogix using 1756-CNB module
• PLC-5/20C, PLC-5/40C, PLC-5/60C, PLC-5/80C
Publication 2711P-UM001F-EN-P - March 2007
Terminal Connections
181
Minimum Requirements
The software and firmware must be installed on the development
computer and the PanelView Plus terminal to configure and
communicate with an Allen-Bradley controller on a ControlNet
network.
ControlNet Unscheduled Communications
Software/Firmware
PanelView Plus 700 to 1500
PanelView Plus 400 or 600
RSView Studio
Version 3.10 or later
Version 4.0 or later
RSView Machine Edition Runtime
Version 3.10 or later
Version 4.0 or later
ControlNet Module Firmware
2711P-RN15S, Series A, Rev A
2711P-RN15C, Series B, Rev A
(1)
or later
(firmware version 2.07 or later)
(1)
This applies to terminals that are ordered as pre-configured units with the ControlNet module.
ControlNet Scheduled Communications
Requirements
PanelView Plus 700 to 1500
PanelView Plus 400 or 600
RSView Studio
Version 3.20 or later
Version 4.0 or later
RSView Machine Edition Runtime
Version 3.20.04 or later
Version 4.0 or later
RSNetWorx for ControlNet
Version 5.11 or later
Version 6.0 or later
RSLogix 5000
Version 13.0 or later
Version 15.0 or later
ControlNet Module Firmware
2711P-RN15S, Series A, Rev C
2711P-RN15C, Series B, Rev A
(1) or later
(firmware version 3.08 or later)
(1)
This applies to terminals that are ordered as preconfigured units with the ControlNet module.
WARNING
The ControlNet Communications Module, cat. no.
2711P-RN15S, will not run with RSView ME firmware version
3.20.04 or earlier. All ControlNet Modules with version 3.07
firmware must be upgraded to version 3.08 or later; otherwise,
outputs may turn on an indeterminate state.
Publication 2711P-UM001F-EN-P - March 2007
182
Terminal Connections
ControlNet Connections
2711P-RN15C ControlNet Module for 400 and 600 Terminals
Channel B
Redundant BNC
Cable Connectors
Channel A
LED B
Pin
1
2
3
4
5
6
7
8
Shell
NAP Signal
Signal Common
No Connection
TX_H
TX_L
RX_L
RX_H
No Connection
Signal Common
Earth Ground
Network Access Port (NAP)
RJ-45 connector for temporarily connecting programming
terminals to devices on a ControlNet network
LED A
2711P-RN15S ControlNet Module for 700 to 1500 Terminals
LED A
Pin
1
2
3
Network Access Port (NAP)
4
RJ-45 connector for temporarily
connecting programming terminals 5
to devices on a ControlNet network 6
7
8
Channel A
Shell
Redundant BNC
Cable Connectors
Channel B
LED B
Pin 1
A
NAP Signal
Signal Common
No Connection
TX_H
TX_L
RX_L
RX_H
No Connection
Signal Common
Earth Ground
B
Allen Bradley
ControlNet
ATTENTION
Publication 2711P-UM001F-EN-P - March 2007
Do not connect more than one ControlNet network to the
Communications Module. If you attempt to connect a second
network to the module, your communication system will
operate erratically.
Terminal Connections
183
NAP and Redundant Cables
Refer to the ControlNet Coax Media Planning and Installation Guide,
publication CNET-IN002, for descriptions of ControlNet components.
Item
Cat. No.
RG-6 quad-shield
1786-RG6
Coax repeater
1786-RPT, -RPTD
Coax taps
1786-TPR, -TPS, -TPYR, -TPYS
Network access cable
1786-CP
Coax tool kit
1786-CTK
Segment terminators
1786-XT
BNC connectors
1786-BNC, -BNCJ, -BNCP, -BNCJ1
IMPORTANT
Do not connect to a network using both the redundant cable
BNC connector and the Network Access Port (NAP).
Connect the Module to the Network
You can connect the ControlNet Module:
• directly to a ControlNet network, which requires a tap.
• to a device already connected to the ControlNet network.
WARNING
When used in a Class I, Division 2, hazardous location, this
equipment must be mounted in a suitable enclosure with
proper wiring that complies with the governing electrical
codes.
Do not connect or disconnect any communication cable with
power applied to this device or any device on the network. An
electrical arc could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
DeviceNet Module
Terminals with a DeviceNet communication module support
communication and the transfer of applications between devices on a
DeviceNet network.
Publication 2711P-UM001F-EN-P - March 2007
184
Terminal Connections
Related Information
For more information on DeviceNet products, refer to these
publications:
• DeviceNet Selection Guide, publication DNET-SG001
• DeviceNet Media Design Installation Guide, publication
DNET-UM072
• DeviceNet Tips & Tricks Brochure, publication DNET-BR003
The Rockwell Automation website http://rockwellautomation.com
provides information and product descriptions of DeviceNet products.
Under the Products and Services heading, select Communications.
DeviceNet Protocol
The terminals support DeviceNet Scheduled I/O only. This protocol
allows direct connection of field devices such as lights, drives, and
valves. It also provides a control architecture that supports multiple
processors. The DeviceNet network is a trunk/drop or bus-based
network that supports up to 64 nodes and operates at 125, 250, or
500 Kbps.
Compatible DeviceNet Controllers
A terminal with a DeviceNet module communicates with an SLC-500
and PLC-5 (PCCC commands), or a ControlLogix processor (CIP
protocol) using Unscheduled messaging. Supported controllers
include:
• ControlLogix using 1756-DNB module.
• PLC-5 with a 1771-SDN module.
• SLC 5/03 - SLC 5/05 with a 1747-SDN module.
Minimum Requirements
Software/Firmware
PanelView Plus 700 to 1500
PanelView Plus 400 and 600
RSView Studio
Version 4.0 or later
Version 4.0 or later
RSView Machine Edition Runtime
Version 4.0 or later
Version 4.0 or later
DeviceNet Module
2711P-RN10H
2711P-RN10C
Publication 2711P-UM001F-EN-P - March 2007
Terminal Connections
185
DeviceNet Connections
2711P-RN10C DeviceNet Module for 400 and 600 Terminals
I/O Status Indicator
NET Status
Indicator
MOD Status Indicator
Red
White
Shield
Blue
Black
2711P-RN10H DeviceNet Module for 700 to 1500 Terminals
NET Status
Indicator
MOD Status Indicator
I/O Status Indicator
Red
White
Shield
Blue
Black
WARNING
Do not connect or disconnect any communication cable with
power applied to this device or any device on the network. An
electrical arc could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
Publication 2711P-UM001F-EN-P - March 2007
186
Terminal Connections
DeviceNet I/O Status Indicator
This bicolor (green/red) LED provides information on the states of
inputs and/or outputs.
Condition
Status
Indication
Off
Outputs active
All outputs are active.
Inputs active
All inputs are active.
Outputs active
One or more outputs are active and
under control, and no outputs are
faulted.
Inputs active
One or more inputs are active and
producing data, and no inputs are
faulted.
Flashing green(1)
Outputs idle
One or more outputs are idle, and no
outputs are active or faulted.
Flashing red (1)
Outputs faulted
One or more outputs are faulted, and
may be in the fault state.
Inputs faulted
One or more inputs are faulted, and
may be in the fault state.
Outputs forced off
One or more outputs are forced off
(may be an unrecoverable fault).
Input unrecoverable fault
One or more inputs has an
unrecoverable fault.
Green
Red
(1)
Publication 2711P-UM001F-EN-P - March 2007
The flash rate of the LED is approximately 1 flash per second. The LED should be on for approximately 0.5
seconds and off for approximately 0.5 seconds.
Terminal Connections
187
DeviceNet Module (MOD) Status Indicator
This bicolor (green/red) LED provides device status. It indicates
whether or not the device has power and is operating properly.
Condition
Status
Indication
Off
No power
No power applied to device.
Green
Device operational
Device is operating in a normal
condition.
Flashing green(1)
Device in standby
(device needs
commissioning)
Device needs commissioning due to
configuration missing, incomplete, or
incorrect.
Flashing red (1)
Recoverable fault
For example, the device’s scan list
configuration does match the actual
network configuration.
Red
Unrecoverable fault
Device has an unrecoverable fault.
Cycle power to your computer. If the
problem persists, the device may
need to be replaced.
Device self testing
Device is in self test. Refer to the
DeviceNet Specification, Volume II,
Identity Object.
(1)
The flash rate of the LED is approximately 1 flash per second. The LED should be on for approximately 0.5
seconds and off for approximately 0.5 seconds.
Publication 2711P-UM001F-EN-P - March 2007
188
Terminal Connections
DeviceNet Network (NET) Status Indicator
This bicolor (green/red) LED indicates the status of the
communication link.
Condition
Status
Indication
Off
Not powered
Device is not online.
Not online
The device has not completed the
Dup_MAC_ID test yet.
The device may not be powered; look
at the Module Status LED.
Flashing green(1)
Online
Device is online, but has no
connections in the established state.
Not connected
The device has passed the
Dup_MAC_ID test, is online, but has
no established connections to other
nodes.
Green
Link okay, online, connected The device is online and has
connections in the established state.
Flashing red (1)
Connection timeout
One or more I/O connections are in
the timed-out state.
Red
Critical link failure
Failed communication device. The
device has detected an error that has
rendered it incapable of
communicating on the network
(Duplicate MAC ID or Bus-off).
Check network integrity and baud
rate of all devices. Then cycle power
to the card by shutting down and
cycling power to your computer.
(1)
The flash rate of the LED is approximately 1 flash per second. The LED should be on for approximately 0.5
seconds and off for approximately 0.5 seconds.
ATTENTION
Publication 2711P-UM001F-EN-P - March 2007
Extensive use of Change-of-State connections, particularly with
rapidly changing data, can adversely impact the available
DeviceNet network bandwidth. If the network bandwith
becomes consumed, some devices may only be able to
communicate intermittently. This can result in timeout errors
and possible loss of data. If timeouts occur, consider changing
the connection type for some of the Change-of-State
connections to Cyclic or Polled.
Chapter
8
Upgrade Firmware
Chapter Objectives
This chapter covers these topics:
• Transfer applications
• Create an ActiveSync connection
• Upgrade terminal firmware
• Upgrade operating system for CE terminals
Transfer Applications
You can transfer applications using a CompactFlash card or a
computer.
PanelView Plus terminals let you copy or load applications in
configuration mode using a CompactFlash card, see page 75.
The PanelView Plus CE terminals let you copy or load applications
using a CompactFlash card from Windows Explorer or RSView ME
configuration mode.
• To copy files in terminal configuration mode, see page 75.
• To copy files in Windows Explorer, see page 114.
For details on transferring .MER applications from a computer to the
PanelView Plus or PanelView Plus CE terminals, refer to RSView
Studio help or documentation.
Create an ActiveSync
Connection
This section shows how to create an ActiveSync connection between a
computer and a PanelView Plus CE terminal.
Creating an ActiveSync connection is a two-step process.
1. Create a partnership between the devices using a Serial
connection.
2. When the partnership is created, you can then connect the
devices using an Ethernet network.
What You Need
• Computer and a PanelView Plus CE terminal that are connected
to an Ethernet network supporting DHCP.
• ActiveSync software, version 3.7 or later, installed on computer.
You can download ActiveSync from the
http://www.microsoft.com web site.
• 2711-NC13 or 2706-NC13 serial cable for connecting the
PanelView Plus CE terminal to the computer with ActiveSync
installed.
189
Publication 2711P-UM001F-EN-P - March 2007
190
Upgrade Firmware
Create a Partnership with a Serial Connection
IMPORTANT
To complete the ActiveSync installation, you must select the
Serial Connection initially. After that you can switch between
serial and Ethernet connections.
You must also make a valid ActiveSync connection at least once
with the computer.
Install ActiveSync on a Computer
1. Install ActiveSync, version 3.7 or later, on your computer.
2. Connect the PanelView Plus CE terminal to the computer with
ActiveSync installed.
Use a 9-pin straight through cable (2711-NC13 or 2706-NC13) for
a serial connection or an Ethernet cable.
3. Start ActiveSync.
You will see the Get Connected screen.
Initiate Serial Connection on PanelView Plus CE Terminals
Select Start>Menu>Programs>Microsoft ActiveSync>Serial.
The Connecting to Async Connection dialog appears.
Find ActiveSync Connection and Create a Partnership on a Computer
1. When the Connecting to Async Connection dialog appears on
the PanelView Plus CE terminal, select the Next button on the
Getting Connected screen of your computer.
If the Connecting to Async Connection dialog closes before a
connection is established, return to Initiating Connection from
the PanelView Plus CE terminal.
2. Select Yes to create the new partnership.
When the ActiveSync connection is created, a window opens
allowing you to create a new partnership.
3. Enter the name and press Next.
ActiveSync will prompt you for a device name.
4. Press the Next button.
Select any options you want to synchronize.
5. Press the Next button and then the Finish button.
Publication 2711P-UM001F-EN-P - March 2007
Upgrade Firmware
191
Terminate Connection on PanelView Plus CE Terminals
1. Click the ActiveSync connection utility on the taskbar.
The Connection Status dialog should appear.
2. Press the Disconnect button to terminate the connection, may
take 30 seconds.
Connect via an Ethernet Connection
Now that a partnership is created using a serial connection, you can
connect to the PanelView Plus CE using an Ethernet connection.
ActiveSync Setup on a Computer
Verify that ActiveSync is configured to accept an Ethernet connection.
By default, the Ethernet connection is enabled. (It is only necessary to
enable the Ethernet connection if it is disabled).
Connect with the Partnership on PanelView Plus CE Terminals
1. Select Start>Programs>Microsoft Active Sync>Ethernet.
The ActiveSync dialog opens. The name of the computer you
connected to via the serial connection will appear.
2. Select Connect.
The Connection Status dialog opens. This dialog remains open
as long as the ActiveSync connection is active.
Closing the dialog will terminate the connection.
Firmware Upgrade Wizard
The Firmware Upgrade Wizard (FUW) lets you upgrade firmware in a
PanelView Plus terminal. Using the FUW, you can:
• create a firmware upgrade card (CompactFlash card) that you
then load in the card slot of the terminal to upgrade firmware.
• upgrade firmware in a terminal that is connected to your
desktop computer using a Serial, Ethernet, or Network
connection via RSLinx Enterprise software (for supported
protocols).
The FUW is available in RSView Studio software or with the Firmware
Upgrade Kit.
Publication 2711P-UM001F-EN-P - March 2007
192
Upgrade Firmware
Before starting the Firmware Upgrade Wizard (FUW), follow these
steps to prepare the terminal for a successful upgrade.
1. Backup all .MER files on the terminal to an external storage card
or network.
2. Delete all applications on the terminal.
3. Record any Ethernet communication settings, such as IP address,
subnet masks, and gateways by selecting Terminal
Settings>Network and Communications>Network
Connections>Network Adapters>IP Address.
4. Disable the Auto-start feature on the terminal by selecting
Startup Options>RSView ME Station Startup and select Go to
Configuration Mode.
5. Reset the terminal.
Upgrade Firmware with a
CompactFlash Card
This section shows how to upgrade the firmware in the terminal using
a CompactFlash card. This is a two step-process. First, you create a
firmware upgrade card with the necessary firmware files. Second, you
load this card in the target terminal to upgrade the firmware.
Create Firmware Upgrade Card
1. Start the Firmware Upgrade Wizard by selecting Start>Rockwell
Software>RSView Enterprise>Firmware Upgrade Wizard.
2. Select Create firmware upgrade card.
• In the Firmware card location text box, select the destination for
the CompactFlash files (folder on the hard drive or physical
location of the CompactFlash card, for example, E:\).
• From the Existing terminal list, select the type of terminal you
are upgrading, then press Next.
Publication 2711P-UM001F-EN-P - March 2007
Upgrade Firmware
193
3. From the Firmware source folder list, select the location of the
firmware files.
The default location is C:\Program Files\Rockwell
Software\RSView Enterprise\FUPs.
4. From the Upgrade firmware version list, select the version of the
firmware you want to upgrade to, then press Next.
5. Select the appropriate KEPServer drivers and press Next.
If no KEPServer drivers are needed, just press Next.
TIP
If the selected FUP file does not support the KEPServer
drivers, this dialog will not appear.
Publication 2711P-UM001F-EN-P - March 2007
194
Upgrade Firmware
6. Select Finish to copy the firmware source files to the location
specified in step 2.
If the files were created in a separate folder on a local
TIP
hard drive, copy the files to the root directory of the
CompactFlash card.
Upgrade Firmware in Terminal with Firmware Upgrade Card
1. Insert the CompactFlash card into the card slot of a powered
terminal.
A dialog indicates the firmware upgrade is about to occur.
2. Press Upgrade to begin the firmware upgrade.
IMPORTANT
Publication 2711P-UM001F-EN-P - March 2007
Do not remove the CompactFlash card while the upgrade is in
process.
Upgrade Firmware
195
If other terminals exist on the same Ethernet network, the
following error may display:
Error registering name on network (may be duplicate). Change
in system Control Panel and try again.
Ignore this error. It will be corrected during the upgrade. Press
OK to acknowledge error and wait for terminal to reset.
TIP
If a USB mouse is available, you can acknowledge this
error by selecting OK.
3. On touch or touch-screen terminals, you must calibrate the
touch screen by selecting pointers in all four corners of the
screen and pressing the middle of the screen when prompted.
Ignore the following message if it appears. It means RSView ME
is being installed. Do not touch the two buttons that appear with
this message.
Machine edition may be corrupted. Do you want to download
firmware?
4. Remove the card and press F8 or Exit to reset the terminal.
When the upgrade is complete, a dialog appears requesting you
to remove the CompactFlash card from the card slot.
Communication settings are cleared when the terminal is
upgraded. If Ethernet communications is used, reconfigure the
Ethernet communication settings using the values recorded
when preparing the terminal.
5. Replace the .MER files that you backed up before starting the
upgrade or download a new .MER file to the terminal.
6. Load the .MER file and run the project.
You can configure your application to start automatically
TIP
on power cycle under Startup Options.
Publication 2711P-UM001F-EN-P - March 2007
196
Upgrade Firmware
Upgrade Firmware with a
Network (Ethernet)
Connection
You can upgrade the firmware in a terminal that is connected to a
desktop computer using a Serial, Ethernet, or Network with RSLinx
Enterprise software connection.
• Serial connection requires a RAS connection to be set up on
computer. During the RAS setup, you select the COM port.
• Ethernet connection requires that you enter the terminal’s IP
Address.
• Network connection requires RSLinx Enterprise software
where you select the terminal on an existing network.
Both the Serial and Ethernet connection requires the File Transfer
Utility running on the terminal.
This section shows how to upgrade firmware in a terminal using a
Network connection via Ethernet communications.
1. Start the Firmware Upgrade Wizard by selecting Start>Rockwell
Software>RSView Enterprise>Firmware Upgrade Wizard.
Publication 2711P-UM001F-EN-P - March 2007
Upgrade Firmware
197
2. Select Upgrade firmware on terminal and click OK.
3. Select Network connection and click Next.
Use the Ethernet and Serial connections only if the firmware
upgrade is unsuccessful.
4. Locate the terminal on your Ethernet network via its IP address.
Skip to step 6 if you found the terminal. If you do not see the
terminal, right-click the Ethernet driver and add the device to the
browse tree.
Publication 2711P-UM001F-EN-P - March 2007
198
Upgrade Firmware
5. Double-click EthernetIP Devices and select the appropriate
terminal and click OK.
6. Enter the IP address for the terminal and click OK.
7. Select the terminal to be upgraded and click OK.
Publication 2711P-UM001F-EN-P - March 2007
Upgrade Firmware
199
8. From the Firmware source folder text box, select the location of
the firmware files.
The default location is C:\Program Files\Rockwell
Software\RSView Enterprise\FUPs.
9. From the Upgrade firmware version list, select the version of the
firmware you want to upgrade to, then click Next.
PanelView Plus 700
10. Select the appropriate KEPServer drivers and click Next.
If no KEPServer drivers are needed, just click Next.
TIP
If the selected FUP file does not support the KEPServer
drivers, this dialog will not appear.
Publication 2711P-UM001F-EN-P - March 2007
200
Upgrade Firmware
11. Click Finish to start the upgrade.
12. Click Yes to continue the upgrade process.
If the terminal was properly prepared for the upgrade, no
applications should be running.
Firmware files are downloaded to the terminal. This may take
several minutes to 15 minutes.
13. When the download is complete, click OK to reset the terminal.
If other terminals exist on the same Ethernet network, the
following error may display:
Error registering name on network (may be duplicate). Change
in system Control Panel and try again.
Publication 2711P-UM001F-EN-P - March 2007
Upgrade Firmware
201
Ignore this error. It will be corrected during the upgrade. Press
OK to acknowledge error and wait for terminal to reset.
If a USB mouse is available, you can acknowledge the
TIP
error by selecting OK.
14. On touch or touch-screen terminals, you must calibrate the
touch screen by selecting pointers in all four corners of the
screen and pressing the middle of the screen when prompted.
Ignore the following message if it appears. It means RSView ME
is being installed. Do not touch the two buttons that appear with
the message.
Machine edition may be corrupted. Do you want to download
firmware?
Communication settings are cleared when the terminal is
upgraded. If Ethernet communications is used, reconfigure the
Ethernet communication settings using the values recorded
when preparing the terminal.
15. Replace the .MER files that you backed up before starting the
upgrade or download the new .MER files to the terminal.
16. Load the .MER file and run the project.
You can configure your application to start automatically
TIP
on power cycle under Startup Options.
Publication 2711P-UM001F-EN-P - March 2007
202
Upgrade Firmware
Upgrade the Operating
System (OS)
The Operating System (OS) compressed binary image resides in a
binary partition of the Internal (IDE) CompactFlash in the logic
module for PanelView Plus CE terminals. There are two ways to
upgrade the OS:.
• External CompactFlash card during a reboot
• LocalOSUpdate (LocalOSUpdate.exe)
External CompactFlash Card
Follow these steps to upgrade the OS using an external CompactFlash
card.
1. Copy the operating system binary file, SYSTEM.BIN, to a
CompactFlash card.
The file must be named SYSTEM.BIN.
2. Remove power from the PanelView Plus CE terminal.
3. Insert the CompactFlash card into the external card slot on the
terminal.
4. Cycle power to the PanelView Plus CE terminal.
The terminal automatically reboots with the new operating
system.
Local OS Update
1. Copy the operating system binary file to a CompactFlash card.
2. Insert the CompactFlash card into the external card slot of the
PanelView Plus CE terminal.
3. At a CMD prompt on the PanelView Plus CE terminal, run:
LocalOSUpdate <Pathname and Filename>
Example: LocalOSUpdate “\Storage card2\NewOS.BIN”
The terminal automatically reboots with the new operating
system.
4. Verify the new operating system is loaded using the system
application in the control panel.
Publication 2711P-UM001F-EN-P - March 2007
Upgrade Firmware
203
Load PanelView Plus CE Components
You can load PanelView Plus CE Components by using an:
• ActiveSync connection.
• external CompactFlash card.
ActiveSync Connection
When the new operating system is running, load the PanelView Plus
CE components as follows.
1. Establish an ActiveSync connection between your computer and
the PanelView Plus CE terminal, using either a serial or Ethernet
connection (Ethernet is recommended).
Refer to page 189.
2. Open the PanelView Plus CE Install Utility folder on the
PanelView Plus CE Accessory CD and run the
InstallFromActiveSync.exe program.
This program lets you select which features to install and
automatically copies the files from the CD to the PanelView Plus
CE terminal. You must run the program from its directory to
make sure the program locates all the files correctly.
3. Select the desired components from the list of available
components.
Use the >> button to install everything.
Once installed, components can be optionally removed to free
space in the \Storage Card folder.
4. When satisfied with the selections, click Install/Remove.
Depending on the options selected and the speed of your
ActiveSync connection, the download process may take several
minutes.
For a serial ActiveSync connection at 19.2 Kbps, the download
time can be 30 minutes. When the download is complete, you
will see the number of files copied or deleted.
5. Restart the PanelView Plus CE terminal.
Publication 2711P-UM001F-EN-P - March 2007
204
Upgrade Firmware
External CompactFlash Card
When the new operating system is running, load the PanelView Plus
CE components as follows.
1. Open the PanelView Plus CE Install Utility folder on the
PanelView Plus CE Accessory CD and copy the following to an
FAT formatted CompactFlash card:
• InstallFromStorageCard.exe
• pvplusceinstall.ini
• Storage Card File folder
2. Insert the CompactFlash card into the external card slot on the
terminal.
3. Using Windows Explorer, browse the \Storage Card folder and
run InstallFromStorageCard.exe.
4. Select the desired components from the list of available
components.
Use the >> button to install everything.
Once installed, components can be optionally removed to free
space in the \Storage Card folder.
5. When satisfied with the selections, click Install/Remove.
When the operation is complete, you will see a message box
reporting the number of files installed (or removed).
6. Restart the PanelView Plus CE terminal.
Publication 2711P-UM001F-EN-P - March 2007
Chapter
9
Troubleshoot the System
Chapter Objectives
This chapter provides information on how to isolate and correct
common operating problems with system components.
• LED indicators
• Isolate the problem
• Startup error messages
• Startup information messages
• Startup sequence
• Check terminal components
• Ethernet connection
• Application does not run
• File system errors
• System identification errors
• Configuration mode access
• Restart in safe mode
• Clean the display window
LED Indicators
The terminals have two LED indicators to isolate operating problems.
• COMM indicator (green) for communications
• FAULT indicator (red) for hardware faults
•
COMM and FAULT Indicators
205
Publication 2711P-UM001F-EN-P - March 2007
206
Troubleshoot the System
Isolate the Problem
This section provides general troubleshooting information to assist
you when trying to isolate problems.
Check for Adequate Power
A terminal that does not receive adequate power could result in
unpredictable behavior. Verify the power requirements in Appendix A
of this manual.
Check Indicators at Startup
After a successful startup, both LED indicators on the terminal are off
and controlled by the application running on the terminal.
When the terminal starts, the fault (red) indicator should be off except
for a few brief flashes, and the comm (green) indicator on.
• If the indicators on the 700 to 1500 terminals remain off, the
power supply or logic module has failed. Check the power
cable. If the power is not within range, replace the power
supply. If the power is within range, replace the logic module.
• If the indicators on the 400 and 600 terminals remain off, check
the power cable.
Indicator States if Terminal Stops during Startup
Fault (Red)
Indicator
Comm
(Green)
Indicator
Description
Recommended Action
Blinking red LED indicates a recoverable error.
Blinking
Off
Last firmware download
failed.
Reload firmware using
Firmware Upgrade Wizard
(FUW) utility.
Blinking
Blinking
EBC boot loader firmware
failed or is missing.
Reload firmware using
Firmware Upgrade Wizard
(FUW) utility.
Blinking
On
Windows CE OS firmware
failed or is missing.
Reload firmware using
Firmware Upgrade Wizard
(FUW) utility.
Solid red LED indicates a nonrecoverable or fatal error.
Publication 2711P-UM001F-EN-P - March 2007
On
Off
Fatal hardware error occurred.
For the 700 to 1500 terminals,
replace the logic module. For
the 400 or 600 terminals,
replace the terminal.
On
Blinking
Fatal hardware error in
display.
For the 700 to 1500 terminals,
replace the display module.
For the 400 or 600 terminals,
replace the terminal.
Troubleshoot the System
207
Check the Startup Messages for Errors
Record any error message that displays during startup and refer to the
Startup Error Message table on page 209.
Check Voltages and Temperatures
On the 700 to 1500 terminals, check the battery voltage and the
display temperature.
• Enter Configuration mode and select Terminal Settings>System
Information>Terminal Information.
• For PanelView Plus CE terminals, you can also open the
Hardware Monitor control panel application.
The battery voltage must be at least 2.75V dc. Replace the battery if
the voltage is less than 2.75V dc.
The display temperatures should be less than 55 °C (131 °F). The CPU
temperature should be less than 95 °C. If the temperatures are higher,
check for obstructed airflow in the chassis and attempt to moderate
the ambient temperatures within the enclosure and surroundings.
Check the System Event Log
Check the system event log for errors or unexpected reboots.
• Enter Configuration mode and select Terminal Settings>System
Event Log.
• For PanelView Plus CE terminals, you can also open the
Hardware Monitor control application and select the Event Log
tab.
Publication 2711P-UM001F-EN-P - March 2007
208
Troubleshoot the System
Perform Extended Diagnostics
Use extended diagnostics on the 700 to 1500 terminals to perform
more extensive hardware testing at startup.
• Enter Configuration mode and select Terminal Settings>Startup
Tests>Select Tests.
• For PanelView Plus CE terminals, you can also open the
Extended Diagnostics control panel application.
Select one or more of the tests you want to run. Enable extended
diagnostics and set the iteration or repeat count. Restart the terminal.
The serial port test requires a loopback connector with these
connections.
DB9 Connector (female)
N/C
1
RX
2
TX
3
DTR
4
N/C
5
DSR
6
RTS
7
CTS
8
N/C
9
Extended diagnostics are performed at every startup until disabled. A
failure will momentarily halt startup and display an error message.
Publication 2711P-UM001F-EN-P - March 2007
Troubleshoot the System
Startup Information
Messages
Message #
Startup messages display in a specific sequence on the terminal during
startup and typically display for a few seconds. These messages
indicate the startup sequence of the terminal but do not require that
you perform any action.
Displayed Message
Description
Video Initialized
Configures and initializes the graphics video system.
30
Watchdog Test
Tests the watchdog circuitry to verify system integrity.
1
RAM Test
Tests the RAM memory.
31 (1)
Stuck Key
Checks the integrity of the function key hardware.
31.5 (1)
Stuck Touch
Checks the integrity of the touch screen hardware.
32 (1)
Battery Test
Checks the integrity of the battery hardware.
2.5 (1)
Registry Search
Locates and loads the most recent, valid registry. Multiple copies of the registry are
maintained. If power is lost during a registry update, a valid registry is available the next
time power is applied to the terminal.
37
(1)
2
209
Image Search
Checks for new OS firmware upgrade on the external CompactFlash card and the serial port.
11 (2)
Downloading Image
Downloads a new OS firmware upgrade to internal RAM. Message may remain on screen
for several minutes.
50 (1)
External CF
Transfers a new OS firmware upgrade from the external CompactFlash card to the terminal.
Message may display for several minutes.
20 (2)
Transfer Image
Programs the OS firmware just downloaded into RAM. Message may remain on screen for
several minutes.
23 (1)
Internal CF
Programs the OS firmware just downloaded into the internal flash memory. Message may
display for several minutes.
24
CRC Check
Checks the integrity of the OS firmware.
Decompress System
Decompresses the compressed OS firmware into RAM.
28
Starting System
Launches the operating system (OS).
29
System Check ###
Checks internal file system integrity (### is percent progress indicator).
System Check
Disables internal file system integrity check. Contact technical support.
27 (2)
29.1
(1)
The status number and message displays only on the 700 to 1500 terminals.
(2)
The status number and message displays only on the 400 and 600 terminals.
Publication 2711P-UM001F-EN-P - March 2007
210
Troubleshoot the System
Startup Sequence
This flow chart provides a sequence of startup operations for the
terminal and shows system information messages that are displayed
on the terminal.
Power On
Display copyright message, bootcode versions and Testing... message
Initialize Video - Display 37 Video Initialized (700 to 1500 only)
Perform Power On Self Test
Display 30 Watchdog Test
Display 1 RAM Test
Display 31 Stuck Key (700 to 1500 only)
Display 31.5 Stuck Touch (700 to 1500 only)
Display 32 Battery Test (700 to 1500 only)
Display 2.5 Registry Search (700 to 1500 only)
Any POST failures?
Yes
No
Check for new OS
Display 2 Image Search
No
Do serial or external CF card download?
Yes
Serial or CF card Download of OS
Display 11 Download to RAM (400 and 600 only)
Display 50 External CF (700 to 1500 only)
Program OS into flash
Display 20 Transfer Image (400 and 600 only)
Display 23 Internal CF (700 to 1500 only)
Check OS integrity
Display 24 CRC Check
Decompress OS to RAM
Display 27 Decompress System (400 and 600 only)
Jump to OS
Display 28 Starting System
Perform final system check (700 to 1500 only)
Display 29 System Checkor
Display 29.1 System Check (if skipping check)
Publication 2711P-UM001F-EN-P - March 2007
Display Error...
message and HALT
Troubleshoot the System
Startup Error Messages
211
When an error occurs, the terminal displays the error number with a
text message. The word ERROR! appears under this line in different
languages.
# Displayed Message
ERROR! FEHLER! ERREUR! ERRORE!
Error #
Displayed Message
Description
Recommended Corrective Action
RAM Test
RAM Test failure
Reset the terminal.
400 and 600: If error persists, replace the terminal.
700 to 1500: If error persists, reseat the SO-DIMM RAM
module. If error still persists, replace the logic module.
14 (1)
RAM Header Check
OS firmware that is downloading is not
compatible with hardware.
Check that you are using the correct version and type of
firmware upgrade. Reset the terminal and upgrade with the
correct firmware version.
20 (1)
Transfer Image
Programming the downloaded OS
firmware into flash failed.
Reset the terminal and attempt the firmware upgrade again. If
error persists, replace the terminal.
Download Task (1)
OS firmware that is downloading to the
terminal is too large.
Check that you are using the correct version and type of
firmware upgrade. Reset the terminal and upgrade with the
correct firmware version.
Internal CF (2)
Error programming the new OS firmware
to internal CompactFlash.
Reload the firmware. If error persists, replace the internal
CompactFlash. If error still persists, replace the logic module.
CRC Check
Checksum of the OS firmware failed.
Reload the firmware.
400 and 600: If error persists, replace the terminal.
700 to 1500: If error persists, replace the internal CompactFlash
card. If error still persists, replace the logic module.
25 (1)
Invalid Prod Family
OS firmware that is downloading is not
compatible with terminal.
Check that you are using the correct version and type of
firmware upgrade. Reset the terminal and upgrade with the
correct firmware version.
27 (1)
Decompress System
Error decompressing the OS firmware
from flash to RAM.
Reload the firmware. If error persists, replace the terminal.
30
Watchdog Test
Watchdog test failure
Reload the firmware.
400 and 600: If error persists, replace the terminal.
700 to 1500: If error persists, replace the logic module.
31
Stuck Key
Function key failure
Check that nothing is pressed against a key. Reset the terminal
without key presses. If error persists, replace display module.
31.5 (2)
Stuck Touch
Touch screen failure
Check that nothing is pressed against the touch screen. Reset
the terminal without touch screen presses. If error persists,
replace the display module.
32 (2)
Battery Test
Battery failure
Replace the battery. If error persists, replace the logic module.
NVRAM Access
Nonvolatile memory failure
Upgrade the system firmware to revision 3.10.03 or later.
3a (1)
Stuck Touch
Touch screen failure
Check that nothing is pressed against the touch screen. Reset
the terminal without touch screen presses. If error persists,
replace the terminal.
40
EXE Check
System OS firmware is missing or corrupt. Reload the firmware.
400 and 600: If error persists, replace the terminal.
700 to 1500: If error persists, replace the internal CompactFlash
card. If error still persists, replace the logic module.
50 (2)
External CF
Error loading the OS firmware from the
external CompactFlash card.
1
23
24
33.5 (2)
(1)
The error number and message displays only on the 400 and 600 terminals.
(2)
The error number and message displays only on the 700 to 1500 terminals.
Reload the firmware. If error persists, replace the external
CompactFlash card and attempt the firmware upgrade again.
Publication 2711P-UM001F-EN-P - March 2007
212
Troubleshoot the System
Check Terminal
Components
This section provides tips on how to isolate problems with individual
components of the terminal, including the display, touch screen,
keypad, attached keyboard or mouse.
Isolate Problems with the Display
The table provides tips to help you resolve problems with display.
If you are unable to resolve the problem, replace the display. If this
corrects the problem, then the display was not functioning properly.
Symptom
Recommended Action
The display is dim or unreadable?
Check the brightness setting on 700 to 1500
displays.
• Enter Configuration mode and select Terminal
Settings>Display>Display Intensity.
• On PanelView Plus CE devices, you can also open
the Display control panel application and select
the Backlight tab.
Check the contrast setting on 400 or 600 grayscale
terminals.
• Enter Configuration mode, and select Terminal
Settings>Display>Display Contrast.
The backlight is turning off or dimming the
display unexpectedly.
Check the screen saver settings.
• Enter Configuration mode and select Terminal
Settings>Display>Screen Saver.
• On PanelView Plus CE devices, you can also open
the Display control panel application and select
the Screen Saver tab.
A startup error appears during startup.
Publication 2711P-UM001F-EN-P - March 2007
Record the message and check the startup error
messages table.
Troubleshoot the System
213
Isolate Problems with the Touch Screen
The table provides tips to help you resolve problems with the touch
screen.
If you are unable to resolve the problem, replace the 700 to 1500
display module or bezel. If this corrects the problem, then the touch
screen was not functioning properly.
Potential problems
Recommended Action
The touch screen is not operating correctly.
Calibrate the touch screen.
• Enter Configuration mode and select Terminal
Settings>Input Devices>Touch
Screen>Calibration.
• On PanelView Plus CE devices, you can also open
the Touch control panel application and select
the Calibration tab.
The calibration requires four user screen touches.
When the touches do not converge to a satisfactory
calibration, you are asked repeatedly for additional
screen touches; the calibration process never
terminates.
A touch screen that does not calibrate is not present
or not functioning properly. Replace the 700 to 1500
display module or the 400 to 600 terminal.
The display may not have a touch screen.
Check the catalog number of the unit. Verify that
your terminal has a touch screen by looking at the
label on the terminal.
The screen cursor is not visible.
Verify that the cursor is enabled.
• Enter Configuration mode and select Terminal
Settings>Input Devices>Touch Screen>Cursor.
• In PanelView Plus CE, open the Display control
panel application and select the Cursor tab.
The touch screen does not accept touch
input.
Attach a USB mouse to check whether the problem
is with the touch screen or the application.
• If the mouse works, but the touch screen does
not, then the touch driver or touch screen is not
functioning properly.
• If both the mouse and the touch screen are not
working, then it is an application problem.
Touch input and dragging is inaccurate. The
touch screen is present and working but
requires calibration.
Calibrate the touch screen.
• Enter Configuration mode and select Terminal
Settings>Input Devices>Touch
Screen>Calibration.
• On PanelView Plus CE devices, you can also open
the Touch control panel application and select
the Calibration tab.
Publication 2711P-UM001F-EN-P - March 2007
214
Troubleshoot the System
Isolate Problems with the Keypad
The table provides tips to help you resolve problems with the terminal
keypad.
If you are unable to resolve the problem, replace the 700 to 1500
display module. If this corrects the problem, then the display was not
functioning properly.
Potential Problems
Recommended Action
The hold-off delay may be longer than
expected or multiple key presses might be
inhibited by multi-key lockout.
Check keypad settings.
• Enter Configuration mode and select Terminal
Settings>Input Devices>Keypad.
Home, End, Page Up or Page Down are not
supported when single key or multi-key
lockout is enabled.
The keypad is not accepting key input.
• On PanelView Plus CE devices, you can also open
the Keypad control panel application.
Check the key input by attaching a USB keyboard.
• If the keyboard works, but the keypad does not,
then the keypad driver or keypad is not working.
• If both the keypad and keyboard are not working,
then the problem may be the application.
Keys on the keypad of a PanelView Plus CE
terminal are not mapped correctly.
Check the keypad mapping.
• You can remap or disable the keys on the
PanelView Plus CE terminal can using the Keypad
Configuration Utility (KCU). Use the KCU to check
the current keypad configuration.
• Restart in Safe mode to use the default keypad
mappings.
On PanelView Plus CE terminals, problems
with keypad input may be the fault of the
application.
On PanelView Plus CE terminals only:
• Press a key outside the application such as an
edit box in the shell. If the keypad input works
outside the application, then the application is at
fault.
• Press Ctrl+Esc simultaneously to open the Start
menu, cursor to run, type numbers and viewable
characters into the Run dialog.
Publication 2711P-UM001F-EN-P - March 2007
Troubleshoot the System
215
Isolate Problems with the Mouse
The table provides tips to help you resolve problems with the mouse.
Potential Problems
Recommended Action
The mouse is not operating correctly.
Check the USB cable and connection. Detach and
then reattach the mouse. Cycle power to the
terminal.
The screen cursor may not be visible or the
mouse settings may need adjusting.
Check if the screen cursor is disabled:
• Enter Configuration mode and select Terminal
Settings>Input Devices>Touch Screen>Cursor.
• For a PanelView Plus CE terminal, you can also
open the Display control panel application.
Check the mouse settings.
• Enter Configuration mode and select Terminal
Settings>Input Devices>Mouse.
• For a PanelView Plus CE terminal, you can also
open the Mouse control panel application.
The mouse is a keyboard/mouse USB
composite device.
Attach a standalone USB mouse.
The USB mouse may not be working or
noncompliant.
Replace the USB mouse. Try a different model or
manufacturer. If attaching a new mouse resolves the
problem, then the old mouse was not working or
noncompliant.
Refer to Appendix B for a list of valid USB devices
that are compatible with the terminal.
You can also check the Knowledgebase at the
http://support.rockwellautomation.com site for a list
of USB devices that are compatible with the
terminal.
Publication 2711P-UM001F-EN-P - March 2007
216
Troubleshoot the System
Isolate Problems with the Keyboard
The table provides tips to help you resolve problems with the
keyboard.
Potential Problems
Recommended Action
The keyboard does not work.
Check the USB cable and connector. Detach and
reattach the keyboard. Verify a good connection.
Cycle power to the terminal.
Keyboard keys may not be enabled as
expected.
Check for enabled Alt-Ctrl keys.
• Enter Configuration mode and select Terminal
Settings>Input Devices>Keyboard.
The keyboard is not accepting key input.
Check the key input using the keypad.
• If the keypad works, but the keyboard does not,
then the keyboard driver or keyboard is not
working.
• If both the keypad and keyboard are not working,
then the problem is probably with the
application.
On PanelView Plus CE terminals, problems
with keyboard input may be the fault of the
application.
On PanelView Plus CE terminals only:
• Press a key outside the application such as an
edit box in the shell. If the keypad input works
outside the application, then the application is at
fault.
• Press Ctrl+Esc simultaneously to open the Start
menu, cursor to run, type numbers and viewable
characters into the Run dialog.
The keyboard is a keyboard/mouse USB
composite device.
Attach a standalone USB keyboard.
The USB keyboard may not be a compliant
device.
Replace the USB keyboard. Try a different model or
manufacturer. If a new keyboard resolves the
problem, then the old keyboard was probably
noncompliant.
Refer to Appendix B for a list of valid USB devices
that are compatible with the terminal.
You can also check the Knowledgebase at the
http://support.rockwellautomation.com site for a list
of USB devices that are compatible with the
terminal.
Publication 2711P-UM001F-EN-P - March 2007
Troubleshoot the System
Ethernet Connnection
217
This section provides tips on how to isolate Ethernet problems.
• Check the LED indicators at the Ethernet connector. The
green LED indicates a communications link and should be ON.
The amber LED indicates data activity and should be flashing.
Verify that there is a connection to the hub?
• Check the cable connections and quality of cable. Check for
good connections and things such as quality, crimping, hub
connection, and uplink ports.
• Check the IP Address of the Built-in Ethernet Controller.
Enter Configuration mode and select Terminal
Settings>Networks and Communications>Network
Connections>Network Adapters. In PanelView Plus CE, open the
Network and Dial-up Connections control panel application
If DHCP is enabled, the device expects a valid IP address to be
acquired within a several seconds after startup. The TCP/IP
protocol automatically assigns 169.254.nnn.nnn when it fails to
acquire an IP address from the server. In general, an IP address
that begins with 169 will not support a network connection.
A bad Ethernet connection and the absence of a valid IP address
are typically reported in a Communications error message box
with the Winsock critical error 10065 - No route to host.
• Check for conflicting IP addresses. If DHCP is not enabled,
make sure the IP address you specify is not in conflict with the
address of another device on the network.
• Check the device name of the terminal. Do not allow devices
on the network with same host name. Enter Configuration mode
and select Terminal Settings>Communications and
Networks>Network Connections>Device Name. In PanelView
Plus CE, open the System control panel application
• Contact your Network Administrator to check peer or
server settings. The other side of the Ethernet connection may
also be a problem.
• Use the network utilities Ping.exe and Ipconfig.exe (CE
Terminals only)
• Check the requirements of network applications (CE
Terminals only). Network applications may have specific
requirements such as Proxy Settings for Internet Explorer and
Ethernet Configuration for ActiveSync. In PanelView Plus CE,
open the Communications control panel application.
• Check the multi-homed devices (CE terminals only).
Multi-homed (more than one Ethernet node) devices have the
same issues as those above but with more potential for
confusion and ambiguity. Keep the Network connections as
simple as possible.
Publication 2711P-UM001F-EN-P - March 2007
218
Troubleshoot the System
Application Does Not Run
If the PanelView Plus application does not start, there may be a
problem with the .MER RSView Machine Edition file. Check for a
startup screen and compatible version.
If a PanelView Plus CE application does not run at startup, try to run
the application manually. If the application runs manually, then the
operating system may be starting up with an invalid shortcut path.
Check the shortcuts in the folder:
\Storage Card\Windows\StartUp
Check the syntax of each shortcut path in the Startup folder and verify
that a valid target application exists.
Check that the application is not missing components or required
DLLs. Remove and reload the application.
Configuration Mode Access
To access Configuration mode, your RSView .MER application must
contain a screen with a Goto Configure mode button. When the
terminal is running the application, you can press this button to access
Configuration mode.
If the terminal is configured to enter Configuration mode at startup
and does not, then reload the firmware.
File System Errors
The file system on PanelView Plus CE terminals is checked at startup
and errors are reported in a message box. Record the error
information and always elect to correct the problem. Typically, the
message box will reappear until the error is corrected.
File system errors are rare and can usually be corrected. The most
common cause of lost clusters and file/directory size mismatches
within a FAT file system is an unexpected power outage while writing
to the file system. Always stop applications before removing power so
that data is cleanly flushed out to the file system and the file system is
brought to an orderly stop.
Although the RSView ME application runs from RAM, applications
such as data and event logging, and historical trending, write to flash
memory and should be stopped before removing power.
Publication 2711P-UM001F-EN-P - March 2007
Troubleshoot the System
Advanced Diagnostics for
CE Terminals
219
Ping and ipconfig are invaluable for network debugging along with
some knowledge of IP and the Winsock error codes.
• Try to ping the destination host.
• Check the destination address.
• Check whether you have a router configured in your network
system (your WinSock implementation).
• Use the tracert command at the command prompt on the
desktop to try and determine where the failure occurs along the
route between your host and the destination host.
• Some utility programs are distributed on the Accessories CD.
Others can be developed using the software development kit
(SDK).
• Take advantage of alternate connectivity - mouse versus touch
screen, keyboard versus keypad, serial communications, and
alternate Ethernet connections.
• Enable the crash logger and examine the EXCEPTIONS.LOG file
from the PanelView Plus CE terminal when suspecting an
operating system or application crash.
• Store the current operating system on an external CompactFlash
card. You can then use this card to update the terminal in case
the operating system is out-of-date or corrupted.
• Store Autorun.exe utilities on an external CompactFlash card
that can be easily run by inserting the card in the external
CompactFlash card slot of the terminal.
• Know useful keyboard shortcuts so that you can navigate
around the system without a mouse or touch screen.
• Check the event log in the Hardware Monitor control panel
application or under Terminal Settings>System Event Log in
Configuration mode. Look for error conditions or reasons for
unexpected reboots.
• Check the configuration settings in the PanelView Plus CE
control panel applications or terminal Configuration mode.
Publication 2711P-UM001F-EN-P - March 2007
220
Troubleshoot the System
System Identification Errors
The error messages in this section appear on startup if incorrect or
invalid components are used with the 700 to 1500 terminals.
• This dialog appears if a PanelView Plus CE logic module is
attached to a PanelView display module. We recommend that
you use a PanelView Plus CE display module with a PanelView
Plus CE logic module. This is a warning letting you continue to
operate.
• This dialog appears if the PanelView Plus logic module contains
a 2711P-RWx internal CompactFlash card for the PanelView Plus
CE terminal.
After pressing OK, you will be asked to power off the terminal
and insert a valid 2711P-RWx internal CompactFlash card for the
PanelView Plus terminal.
• This dialog appears if the PanelView Plus CE logic module
contains a 2711P-RWx internal CompactFlash card for the
PanelView Plus terminal.
.
(6189-RWX)
After clicking OK, you will be asked to power off the terminal
and insert a valid 2711P-RWx internal CompactFlash card for the
PanelView Plus CE terminal.
Publication 2711P-UM001F-EN-P - March 2007
Troubleshoot the System
221
• This dialog appears if the internal CompactFlash in the
PanelView Plus logic module is corrupt. This is a fatal error.
After clicking OK, you will be asked to power off the terminal
and insert a valid 2711P-RWx internal CompactFlash card.
Restart in Safe Mode
On PanelView Plus CE terminals, use the default switch with the reset
switch to start the terminal in Safe mode. This diagnostic mode
reduces the system to a known state that permits recovery from a
software problem. Safe mode ignores all user changes to the system
and avoids any problems that are due to interactions with end-user
software or changes. Once the system is running in Safe mode, you
can repair the offending applications or changes that caused the
problem.
When the PanelView Plus CE terminal is restarted in Safe mode, the
following occurs:
• The Persistent Registry is ignored and the Default Registry is
used. The Persistent Registry is restored at the next reboot unless
the Default Registry is saved (flushed), in which case it becomes
the new Persistent Registry.
• The \Windows\Startup folder is ignored, inhibiting most startup
actions. All user applications that launch automatically at startup
are shortcuts in the \Startup folder.
• Depending on the state of the system, the touch screen may be
calibrated at startup.
• All custom key configurations (mappings) generated by the
Keypad Configuration Utility (KCU) are ignored.
Publication 2711P-UM001F-EN-P - March 2007
222
Troubleshoot the System
The switches that control safe mode are on the right side of the logic
module above the CompactFlash card slot.
Follow these steps to restart in Safe mode.
1. Insert a thin probe into the hole marked default and press the
switch.
2. Insert the probe into the hole marked reset and press the switch.
The system will restart immediately into the Safe mode.
If you restart the PanelView Plus terminal in safe mode:
1. The default operating system registry is loaded.
2. The operating system boots but RSView Machine Edition
software is not started.
3. The operating system displays the ME may be corrupt diagnostic
screen.
Disregard this message. RSView Machine Edition software is not
corrupt; it has not been loaded on this boot cycle.
4. The next time you reset or power up the terminal, the system
will start normally and run RSView Machine Edition software.
Safe mode indicates that the terminal passes all startup self
TIP
tests and can successfully launch the operating system. Safe
mode is not a diagnostic function for the RSView Machine
Edition application.
Clean the Display Window
Use a protective antiglare overlay for easier cleaning of the display
window.
ATTENTION
Use of abrasive cleaners or solvents may damage the display.
Do not scrub or use brushes.
Follow these steps to clean the display window.
1. Disconnect power from the terminal at the power source.
2. Use a clean sponge or soft cloth with a mild soap or detergent to
clean the display.
3. Dry the display with a chamois or moist cellulose sponge to
avoid water spots.
Remove fresh paint splashes and grease before drying by rubbing
lightly with isopropyl alcohol (70% concentration). Afterward, wash
using a mild soap or detergent. Rinse with clean water.
Publication 2711P-UM001F-EN-P - March 2007
Appendix
A
Specifications
Electrical
Attribute
400 and 600
Input voltage, dc
Power consumption, dc
700 to 1500
Input voltage, dc
Power consumption, dc
400 and 600
Input voltage, ac
Line frequency
Power consumption, ac
700 to 1500
Input voltage, ac
Line frequency
Power consumption, ac
Remote power 700 to 1500 (2711P-RSAC)
Input voltage, ac
Line frequency
Power consumption, ac
PCI slot max available power
Supply, dc
Supply, ac
Value
24V dc nom (18…30V dc)
25 W max (1.0 A at 24V dc)
24V dc nom (18…32V dc)
70 W max (2.9 A at 24V dc)
85…264V ac
47…63 Hz
60V A max
85…264V ac
47…63 Hz
160V A max
85…264V ac
47…63 Hz
120V A max
11 W
5W
Environmental
223
Attribute
Value
Temperature, operating
0…55 °C (32…131 °F)
Temperature, non-operating
-25…70 °C (-13…158 °F)
Heat dissipation
400 and 600
700 to 1500
85 BTU/hr
240 BTU/hr
Relative humidity
5…95% without condensation
Altitude, operating
2000 m (6561 ft)
Shock, operating
15 g at 11 ms
Shock, nonoperating
30 g at 11 ms
Vibration
10…57 Hz, 0.012 pk-pk displacement
57…500 Hz, 2 g pk acceleration
Enclosure Ratings
NEMA Type 12, 13, 4X (Indoor use only),
IP54, IP65
Publication 2711P-UM001F-EN-P - March 2007
224
Specifications
Display
Attribute
Display type
400 and 600 monochrome
600 to 1500 color
Monochrome passive matrix, film
compensated super-twist nematic (FSTN)
Color active matrix, thin-film transistor (TFT)
with liquid crystal display (LCD)
Display size, diagonal
400
600
700
1000
1250 and 1250 high-bright
1500
3.8 in.
5.5 in.
6.5 in.
10.4 in.
12.1 in.
15.0 in.
Display area (WxH)
400
600
700
1000
1250 and 1250 high-bright
1500
78 x 59 mm (3.07 x 2.32 in.)
111 x 84 mm (4.37 x 3.30 in.)
132 x 99 mm (5.2 x 3.9 in.)
211 x 158 mm (8.3 x 6.2 in.)
246 x 184 mm (9.7 x 7.2 in.)
304 x 228 mm (12.0 x 9.0 in.)
Resolution
400
600
700
1000
1250 and 1250 high-bright
1500
320 x 240
320 x 240
640 x 480
640 x 480
800 x 600
1024 x 768
Luminance
700 to 1500
1250 high-bright
300 cd/m2 Nits
1000 cd/m2 Nits
Backlight
400
600 to 1500
1250 High-bright
LED
CCFL 50,000 hours life, min.
Backlight not replaceable
Touch screen
Actuation rating
Operating force
Analog resistive
1 million presses
10…110 g
Keypad function keys(1)
Actuation rating
Operating force
Function keys, numeric and navigation
1 million presses
340 g
(1)
Publication 2711P-UM001F-EN-P - March 2007
Value
Number of function keys varies by terminal size.
Specifications
225
Mechanical
Attribute
Value
Weight , approx., HxWxD (for base unit without modules)
400 keypad(1)
600 keypad or keypad and touch(1)
600 touch(1)
700 keypad or keypad and touch
700 Touch
1000 keypad or keypad and touch
1000 touch
1250 keypad or keypad and touch
1250 touch and 1250 high-bright touch
1500 keypad or keypad and touch
1500 touch
562 g (1.24 lb)
930 g (2.05 lb)
789 g (1.74 lb)
1.9 kg (4.2 lb)
1.7 kg (3.8 lb)
2.9 kg (6.3 lb)
2.6 kg (5.7 lb)
3.4 kg (7.6 lb)
3.2 kg (7.1 lb)
4.6 kg (10.0 lb)
4.2 kg (9.3 lb)
Dimensions, approx. HxWxD (for base unit without communication module)
400 keypad
152 x 185 x 90 mm (6.0 x 7.28 x 3.54 in.)
600 keypad or keypad and touch
167 x 266 x 98 mm (6.58 x 10.47 x 3.86 in.)
600 touch
152 x 185 x 98 mm (6.0 x 7.28 x 3.86 in.)
700 keypad or keypad and touch
193 x 290 x 55 mm (7.58 x 11.40 x 2.18 in.)
700 touch
179 x 246 x 55 mm (7.04 x 9.68 x 2.18 in.)
1000 keypad or keypad and touch
248 x 399 x 55 mm (9.77 x 15.72 x 2.18 in.)
1000 touch
248 x 329 x 55 mm (9.77 x 12.97 x 2.18 in.)
1250 keypad or keypad and touch
282 x 416 x 55 mm (11.12 x 16.36 x 2.18 in.)
1250 touch
282 x 363 x 55 mm (11.12 x 14.30 x 2.18 in.)
1250 touch High-bright
282 x 363 x 74 mm (11.12 x 14.30 x 2.90 in.)
1500 keypad or keypad and touch
330 x 469 x 65 mm (12.97 x 18.46 x 2.55 in.)
1500 touch
330 x 416 x 65 mm (12.97 x 16.37 x 2.55 in.)
(1)
Add approximately 95 g (0.21 lb) for communication module.
Publication 2711P-UM001F-EN-P - March 2007
226
Specifications
General
Attribute
Value
Battery life
400 and 600
700 to 1500
5 years min. at 25 °C (77 °F)
4 years min. at 25 °C (77 °F)
Clock
Battery-backed, +/-2 minutes per month
LED indicators
COMM (Green), Fault (Red)
Application flash memory
400 and 600, series A
400 and 600, series B or later
700 to 1500 logic modules, series A to D
700 to 1500 logic modules, series E or later
2711P-RW1
2711P-RW2
2711P-RW3
5 MB
10 MB
12 MB
26 MB
72 MB
195 MB
700-1500 CE logic modules, series E or later
80 MB
2711P-RW6
203 MB
2711P-RW7
446 MB
2711P-RW8
External CompactFlash storage
512 MB max
Agency Certifications
Certifications (1)
Value
c-UL-us
UL Listed Industrial Control Equipment, certified for use in
US and Canada. See File E10314.
UL Listed Industrial Control Equipment for use in:
• Class I, Div 2, Group A, B, C, D
• Class I, Zone 2, Group IIC (2)
• Class II, Div 2 Groups F, G
• Class III Hazardous Locations
Publication 2711P-UM001F-EN-P - March 2007
CE
European Union 89/336/EEC EMC Directive, compliant with:
EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers
C-Tick
Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
(1)
See http://ab.com for declarations of conformity, certificates, and other certification details.
(2)
Applies only to the 1250 high-bright display module.
Appendix
B
Compatible USB Devices
The following table provides a list of compatible USB devices that can
be used on the USB ports of the terminals.
Device
USB Keyboard
USB
Keyboard/Mouse
USB Mouse
USB Hub
227
PanelView Plus
700 to 1500
PanelView Plus
400 and 600
Cat. No. 6189-KBDEPU1U
Yes
Yes
Ortek
MCK-600USB
Yes
Yes
Dell
RT7D10
Yes
Yes
Rockwell Automation
Cat. No. 6189-KBDEPC1U
Yes
No
Logitec
Optical Mouse - M-BJ58
Yes
Yes
Microsoft
Intellimouse D58-00026
Yes
Yes
Atek
USB Mouse
Yes
No
VersaView (Rockwell
Automation)
USB Mouse
Yes
Yes
Belkin
USB 4-Port Hub - ESU021
Yes
Yes
Vendor
Model
Rockwell Automation
Publication 2711P-UM001F-EN-P - March 2007
228
Compatible USB Devices
Publication 2711P-UM001F-EN-P - March 2007
Appendix
C
Available Fonts for Terminal Applications
The following fonts are pre-installed on PanelViewPlus CE terminals:
• True Type fonts (scalable)
– Tahoma.ttf (proportional)
– Courier.ttf (fixed width)
– Arial.ttf (proportional)
• 23 fonts of various sizes migrated from PanelView Standard and
PanelView e terminals (various sizes)
To simplify the creation and downloading of .mer application files on
these devices, use the above list of fonts when developing screens in
RSView Studio software.
Additional fonts are available in RSView Studio software when
developing application screens.
• If the font used to develop screens is not available on the target
device, the closest font is selected.
• If bold or italics is used, and a separate bold or italics font is
unavailable, then the target operating system will use an
algorithm to produce these affects.
In either case, the device screens will look different than they do in
RSView Studio software.
Download Fonts to Terminal
To use additional fonts on a PanelView Plus CE device, copy any of
the font files on the PanelView Plus CE Accessories CD or the RSView
Machine Edition Fonts CD to the following directory on the computer
where RSView Studio software is installed:
c:\Documents and Settings\All Users\Documents\RSView Enterprise\ME\Runtime
You can now use the File Transfer Utility in RSView Studio software to
download the font files to the target device.
1. Select Tools>Transfer Utility.
2. Select Source File>True Type Fonts.
3. Select a font file to download to the device and press the
Download button.
PanelView Plus CE
Accessories CD
229
The following True Type fonts are included on the PanelView Plus CE
Accessories CD:
• Times New Roman.ttf
• Symbol.ttf
• Wingdings.ttf
This CD is not supplied with PanelView Plus terminals.
Publication 2711P-UM001F-EN-P - March 2007
230
Available Fonts for Terminal Applications
RSView Machine Edition
Fonts CD
Additional fonts are available on a CD, titled RSView Machine Edition
Fonts. This CD is available from your local distributor by requesting
View-SP006.
For additional information, refer to the Rockwell Automation
Knowledgebase at http://support.rockwellautomation.com. Select
Knowledgebase under Online Tools and then enter Tech Note ID
A66647102.
Available Fonts
Fonts
File Name
Size (Bytes)
Arial (Subset 1_30)
arial_1_30.ttf
153,720
Arial Black
arialk.ttf
117,028
Arial Bold
arialbd.ttf
288,496
Arial Bold Italic
arialbi.ttf
226,748
Arial Italic
ariali.ttf
207,808
Comic Sans MS
comic.ttf
126,364
Comic Sans MS Bold
comicbd.ttf
111,476
Arial
Comic Sans MS
Courier New
Courier New (Subset 1_30)
cour_1_30.ttf
162,460
Courier New Bold
courbd.ttf
312,920
Courier New Bold Italic
courbi.ttf
236,148
Courier New Italic
couri.ttf
245,032
Georgia
georgia.ttf
149,628
Georgia Bold
georgiab.ttf
141,032
Georgia Bold Italic
georgiaz.ttf
159,736
Georgia
georgiai.ttf
157,388
Impact
Georgia Italic
impact.ttf
136,076
Kino
kino.ttf
28,872
MSLogo
mslogo.ttf
2,500
Symbol
symbol.ttf
69,464
Tahoma (Subset 1_07)
tahoma_1_07.ttf
123,980
Tahoma Bold
tahomabd.ttf
295,432
Times New Roman (Subset 1_30)
times_1_30.ttf
184,976
Times New Roman Bold
timesbd.ttf
334,944
Times New Roman Bold Italic
timesbi.ttf
239,692
Times New Roman Italic
timesi.ttf
248,368
Tahoma
Times New Roman
Publication 2711P-UM001F-EN-P - March 2007
Available Fonts for Terminal Applications
Fonts
File Name
231
Size (Bytes)
Trebuchet MS
Trebuchet MS
trebuc.ttf
69,688
Trebuchet MS Bold
trebucbd.ttf
66,444
Trebuchet MS Bold Italic
trebucbi.ttf
66,348
Trebuchet MS Italic
trebucit.ttf
72,560
Verdana
verdana.ttf
149,752
Verdana Bold
verdanab.ttf
137,616
Verdana Bold Italic
verdanaz.ttf
154,800
Verdana Italic
Verdana
verdanai.ttf
155,076
Webdings
webdings.ttf
118,752
Wingding
wingding.ttf
81,000
Simsun & NSimSun
simsun.ttc
10,500,400
Simsun & NSimSun (Subset 2_50)
simsun_2_50.ttc
3,051,024
Simsun & NSimSun (Subset 2_60)
simsun_2_60.ttc
3,578,692
Simsun & NSimSun (Subset 2_70)
simsun_2_70.ttc
6,975,948
Simsun & NSimSun (Subset 2_80)
simsun_2_80.ttc
8,116,188
Simsun & NSimSun (Subset 2_90)
simsun_2_90.ttc
9,066,640
sunfon.ttf
4,686,044
MingLiU & PMingLiU
mingliu.ttc
8,822,400
MingLiU & PMingLiU (Subset 2_70)
mingliu_2_70.ttc
4,786,488
MingLiU & PMingLiU (Subset 2_80)
mingliu_2_80.ttc
5,772,700
MingLiU & PMingLiU (Subset 2_90)
mingliu_2_90.ttc
7,354,808
msming.ttf
3,172,552
MS Gothic & P Gothic & UI Gothic
msgothic.ttc
8,272,028
MS Gothic & P Gothic & UI Gothic (Subset 1_50)
msgothic_1_50.ttc
4,456,536
MS Gothic & P Gothic & UI Gothic (Subset 1_60)
msgothic_1_60.ttc
6,057,400
Chinese (Simplified) Locale Specific Support
Simsun & NSimSun
SC_Song
Chinese (Traditional) Locale Specific Support
MingLiU & PMingLiU (Choose 1)
MSMing
Japanese Locale Specific Support
MS Gothic
MS Gothic & P Gothic & UI Gothic (Subset 1_70)
msgothic_1_70.ttc
3,795,500
MS Gothic & P Gothic & UI Gothic (Subset 1_80)
msgothic_1_80.ttc
5,438,776
MS Gothic & P Gothic & UI Gothic (Subset 1_90)
msgothic_1_90.ttc
6,408,352
MS Gothic & P Gothic (Subset 30)
msgothic30.ttc
4,197,524
MS Gothic & P Gothic (Subset 30_1_19)
msgothic30_1_19.ttc
3,304,056
Publication 2711P-UM001F-EN-P - March 2007
232
Available Fonts for Terminal Applications
Fonts
File Name
Size (Bytes)
gl_ce.ttf
4,130,084
Gulim & GulimChe (Subset 1_30)
gulim_1_30.ttc
3,010,268
Gulim & GulimChe (Subset 1_40)
gulim_1_40.ttc
4,683,896
Gulim & GulimChe (Subset 1_50)
gulim_1_50.ttc
7,128,756
Gulim & GulimChe (Subset 1_60)
gulim_1_60.ttc
9,360,100
Korean Locale Specific Support
GL_CE
Gulim & GulimChe (Choose 1)
Publication 2711P-UM001F-EN-P - March 2007
Appendix
D
Programmable Key Definitions
The tables in this appendix shows the Windows virtual key code
mapping of each programmable function key on the
PanelView Plus CE terminal.
233
Function Key
Virtual Key
Mapping
Function Key
Virtual Key
Mapping
F1
VK_F1
K1
RA + VK_F1
F2
VK_F2
K2
RA + VK_F2
F3
VK_F3
K3
RA + VK_F3
F4
VK_F4
K4
RA + VK_F4
F5
VK_F5
K5
RA + VK_F5
F6
VK_F6
K6
RA + VK_F6
F7
VK_F7
K7
RA + VK_F7
F8
VK_F8
K8
RA + VK_F8
F9
VK_F9
K9
RA + VK_F9
F10
VK_F10
K10
RA + VK_F10
F11
VK_F11
K11
RA + VK_F11
F12
VK_F12
K12
RA + VK_F12
F13
LS + VK_F1
K13
RS + VK_F1
F14
LS + VK_F2
K14
RS + VK_F2
F15
LS + VK_F3
K15
RS + VK_F3
F16
LS + VK_F4
K16
RS + VK_F4
F17
LS + VK_F5
K17
RS + VK_F5
F18
LS + VK_F6
K18
RS + VK_F6
F19
LS + VK_F7
K19
RS + VK_F7
F20
LS + VK_F8
K20
RS + VK_F8
F21
LS + VK_F9
K21
RS + VK_F9
F22
LS + VK_F10
K22
RS + VK_F10
Publication 2711P-UM001F-EN-P - March 2007
234
Programmable Key Definitions
The following table provides the Windows virtual-key code mapping
for the Alt, Control, and Shift keys on the PanelView Plus CE terminal.
Alt, Control, and Shift Key Mapping
Keyboard
Virtual Key
Equivalent
Mapping
Publication 2711P-UM001F-EN-P - March 2007
Control
VK_LCONTROL
Shift
VK_LSHIFT
Alt
VK_LMENU
Appendix
E
Security Considerations
Ports 137 and 138 are normally open to support the NetBIOS protocol
used by Windows CE.NET similar to other Microsoft and IBM network
operating systems.
Port 80 is open when the Web server is optionally installed from the
PanelView Plus extensions. Otherwise, Port 80 is normally closed.
The FTP server permits a remote computer to run arbitrary commands
and read/write files. The FTP server is optionally installed from the
VersaView extensions. Otherwise, there is no FTP server on the
system.
Simple Network Management Protocol (SNMP) is not supported.
Internet Group Management Protocol (IGMP) is used for IPv4
multicast. A multicast is communication between a single sender and
multiple receivers on a network. IGMP is used to exchange
membership status data between IPv4 routers that support
multicasting and members of multicast groups. A router is an
intermediary device on a communication network that expedites
message delivery by finding the most efficient route for a message
packet within a network, or by routing packets from one subnetwork
to another. A subnetwork is a separate part of an organization’s
network identified through IP addressing.
PanelView Plus CE terminals provide level 2 (full) support for IPv4
multicasting (IGMP version 2) as described in RFC 1112 and RFC 2236.
Security requires a comprehensive application of policies and
technology, and an awareness of security needs and potential
vulnerabilities. You may also want to consult with Rockwell GMS
Network Services for additional assistance.
235
Publication 2711P-UM001F-EN-P - March 2007
236
Security Considerations
Publication 2711P-UM001F-EN-P - March 2007
Index
A
ac power
400, 600 19
700 to 1500 19, 27
connect 54
connections 52
protective-earth connection 52
accessories 22
ActiveSync 110, 117, 120, 121, 189, 190,
191, 203, 217
adapter plates 26
application
installing 111
loading .MER 61
running 62
troubleshooting 218
B
backlight
brightness 78, 126
replacement 24
base unit
400-600 13
700 to 1500 18
battery replacement 27, 150
bezel replacement 25, 152
C
cables 26
runtime communication cables 164
catalog number configuration 22
CCFL backlight control 77
cleaning display 222
communication adapters 27
communication modules 23
400-600 14, 19
700 to 1500 19
installing and replacing 144, 146
communications
cables 164
ControlNet 180
DH+/DH485/RIO module 174, 180
DH485 176
DHPlus 178
Ethernet 172
Remote I/O 179
serial 169
USB ports 168
compatibility of components 138
configuration mode
accessing 57
loading application 61
running application 62
terminal settings 62
control panel applications
date/time 133
display settings 126
Ethernet network configuration 120
extended diagnostics 128
hardware monitor 130
input panel 125
keyboard settings 123
keypad settings 124
mouse settings 125
network 120
regional settings 133
system information 131
touch screen settings 122
ControlNet
cables 164, 183
compatible controllers 180, 184
connections 182
ControlNet protocol 180
modules 182
overview 180
Software Requirments 181
copying files
applications 75
font files 75
cutout dimensions for each terminal 34
D
date 101, 107, 133, 134
dc power 49, 223
connect 51, 54
connections 49
deleting files
applications 74
font files 74
log files 74
DeviceNet
cables 164
compatible controllers 184
configuration 65
connections 185
I/O status indicator 186
minimum requirements 184
module 185
module status indicator 186
network status indicator 188
protocol 183
Publication 2711P-UM001F-EN-P - March 2007
238
Index
DF1
cables 164
DH485
cables 164
port connectors 174, 237
status indicators 175
DHPlus
cables 164
network connections 178
port connectors 174
status indicators 175
diagnostics
in control panel 128
in RSView 72
display
troubleshooting 212
display 400-600
keypad 16
keypad/touch 16
touch screen 15
display modules
high-bright display 20, 22, 32
display modules 700 to 1500 22
keypad 21
keypad/touch 21
replacing 148
touch screen 20
display settings
configuration mode 77
in control panel 126
E
Ethernet
cables 164, 173
connector pinout 172
network configuration 120
troubleshooting 217
external compact flash cards 24, 116, 161
F
firmware upgrade
creating a firmware upgrade card 192
firmware upgrade wizard 191
operating system 202
upgrading from a computer 196
using a firmware upgrade card 194
firmware upgrade kits 27
fonts
additional fonts 229
linking 81
Publication 2711P-UM001F-EN-P - March 2007
pre-installed 229
function keys
keypad terminals 16, 21
virtual key code mapping 233
functional-earth connection 50
H
hardware monitor 130
hazardous locations 29
USB port 30
high-bright display 20, 32
I
IGMP Protocol 173, 235
input devices
input panel 125
keyboard 123
keypad 124
mouse 83, 86, 125
touch screen 122
input panel 60
installation 29
1000 mounting dimensions 42
1250 mounting dimensions 43
1500 mounting dimensions 44
400 mounting dimensions 39
600 mounting dimensions 40
700 mounting dimensions 41
ambient temperature 34
backlight 155
battery 150
bezel 152
clearances 34
communication module 146
display module 700 to 1500 148
enclosures 32
hazardous locations 29
high-bright display 32
legend inserts 159
mounting levers 400-600 35
panel installation 400-600 34
panel installation 700 to 1500 37
product label 158
intended audience 9
internal compact flash 115
compatibility 138
installing and replacing 141
Internet Group Management Protocol
(IGMP) 173, 235
IP address 69
Index
K
keyboard
compatibility 227
mouse compatibility 227
settings 123
troubleshooting 214, 216
keypad legend inserts 24, 159
keypad settings 124
L
languages 104, 133
LED indicators 205
legend inserts
installation 159
loading application 61
logic module 23
700 to 1500
compatibility 138
features 18
installing and replacing 142
M
memory
allocations 131
boot ROM 115
dynamic RAM 116
external compact flash card 116
installing and replacing 141
internal compact flash 115
USB Mass Storage Devices 116
messages
startup error 211
startup information 209
modular components 700 to 1500 18
mounting clips 700 to 1500 27
mounting dimensions
1000 42
1250 43
1500 44
400 39
600 40
700 41
mounting levers 400-600 27, 34
mouse 83, 86, 125, 168
compatible 227
troubleshooting 214, 215
multikey lockout 124
239
N
NAP 183
network connections 120, 164
O
operating system upgrade
loading PanelView Plus CE components
203, 204
outdoor installation
high-bright displays 32
P
packing list 9
power supply
400 and 600 49, 52
power terminal block
install 46
remove 46
pre-loaded programs 110
print setup
for alarms 87
for diagnostic messages 87
for displays 87
product components 22
protective-earth connection 54
R
RAM 24
compatibility 138
installing and replacing 141
registry settings 115
Remote I/O
cables 164, 179
connection 179
port connectors 174
status indicators 175
reset switch
400-600 55
resetting terminal 58
400-600 55
RSView 57
S
safe mode 221
screen saver 126
security considerations 235
Publication 2711P-UM001F-EN-P - March 2007
240
Index
serial communications
computer connection 171
connections 169
DF1 169
DH485 169
null modem cable 170
ports 169, 172
printing 169, 171
transferring applications 169
using a modem 170
shortcut keys 112
Shortcut paths for startup 94
Simple Network Management Protocol
(SNMP) 173, 235
SNMP Protocol 173, 235
software 11, 111
specifications
agency certifications 226
electrical 223
environmental 223
mechanical 225
startup
error messages 211
information messages 209
problems 218
sequence 210
tests 129
storage, permanent 114, 115
stylus, recommended 20
support 100
system
event log 97, 130
information 131
system identification errors 220
T
terminal information 98, 130
terminal settings 62
date 101
diagnostics 72
long date format 108
short date format 107
system event log 97
terminal info 98
time 102
time format 106
time zone 103
time 102, 133
Publication 2711P-UM001F-EN-P - March 2007
format 106, 133
touch screen
calibration 122
cursor enable 85
double-tap sensitivity 86, 122
troubleshooting 213
transferring files 75
troubleshooting 205
accessing configuration mode 218
advanced 219
display module 212
Ethernet connection 217
file system 218
general 206
keyboard 216
keypad 214
LED indicators 205
mouse 215
starting in safe mode 221
startup error messages 211
startup information messages 209
system identification errors 220
touch screen 213
U
USB devices 227
USB ports 168
compatible 227
connector pinouts 168
terminals 30
USB Hub 227
USB mass storage devices 116
W
Windows CE .NET 11, 109, 115
applications 110
browsing web pages 114
command bar 113
compiling applications 109
finding files 114
operating system 109
pre-loaded programs 110
printing 114
start menu and taskbar 113
using 111
wiring and safety guidelines 45, 163
Rockwell Automation
Support
Rockwell Automation provides technical information on the Web to assist
you in using its products. At http://support.rockwellautomation.com, you can
find technical manuals, a knowledge base of FAQs, technical and application
notes, sample code and links to software service packs, and a MySupport
feature that you can customize to make the best use of these tools.
For an additional level of technical phone support for installation,
configuration, and troubleshooting, we offer TechConnect Support programs.
For more information, contact your local distributor or Rockwell Automation
representative, or visit http://support.rockwellautomation.com.
Installation Assistance
If you experience a problem with a hardware module within the first 24
hours of installation, please review the information that's contained in this
manual. You can also contact a special Customer Support number for initial
help in getting your module up and running.
United States
1.440.646.3223
Monday – Friday, 8am – 5pm EST
Outside United
States
Please contact your local Rockwell Automation representative for any
technical support issues.
New Product Satisfaction Return
Rockwell tests all of its products to ensure that they are fully operational
when shipped from the manufacturing facility. However, if your product is
not functioning, it may need to be returned.
United States
Contact your distributor. You must provide a Customer Support case
number (see phone number above to obtain one) to your distributor in
order to complete the return process.
Outside United
States
Please contact your local Rockwell Automation representative for
return procedure.
Publication 2711P-UM001F-EN-P - March 2007 245
Supersedes Publication 2711P-UM001E-EN-P - March 2006
Supersedes Publication 6182H-UM001E-EN-P - March 2006
Copyright © 2007 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement