TriScope User Manual

TriScope User Manual
MODEL: SCOPE COLPOSCOPE
USER’S MANUAL
ZOOMSCOPE™ with TRULIGHT COLPOSCOPE
TRISCOPE™ with TRULIGHT COLPOSCOPE
REF: 906043-SP-3, 906043-SP-4, 906043-SP-5,
906043-40TU-5,
906150T-4, 906150T-5,
906043-SP-4C, 906043-SP-5C, 906043-40TU-5C,
906150T-4C, 906150T-5C
WALLACH SURGICAL DEVICES
95 Corporate Drive
Trumbull, CT 06611 USA
Phone: (203) 799-2000
Fax: (203) 799-2002
www.wallachsurgical.com
EC REP
EMERGO EUROPE
Molenstraat 15
2513 BH, The Hague
The Netherlands
IMSC035-DFU • Rev. A • 6/14
Made in the USA
This page left blank intentionally
Table of Contents
Cautions ..........................................................................................................2
ZoomScope
Assembly Instructions ...........................................................................2
Optical Head Adjustment .................................................................... 4
Power Zoom and Focus .......................................................................5
Scope Operation ..................................................................................5
Focusing the ZoomScope with Trulight ...............................................5
Video ZoomScope with Trulight, USB .................................................6
TriScope
Assembly Instructions ..........................................................................7
Operating Instructions ..........................................................................7
Focusing the TriScope ..........................................................................8
Accessories ..........................................................................................8
Digital Camera Attachment ..........................................................8
Digital Photography .....................................................................8
Teaching Tube ............................................................................9
USB Video Attachment ...............................................................9
Arm Adjustment ....................................................................................11
Electrical ...........................................................................................................11
Illumination .......................................................................................................11
Replacing the Fuses .......................................................................................11
Moving the Colposcope with Trulight ............................................................12
Positioning the ColpoScope with Trulight ....................................................12
Maintenance ...................................................................................................12
Warranty Information ...................................................................................12
Service and Repair .......................................................................................13
Explanation of Symbols ..............................................................................14
Specifications
ZoomScope with Trulight Specifications ...............................................15
TriScope Specifications ........................................................................16
For All Scope Colposcope Models ...........................................................17
Classification ........................................................................................17
Environment Conditions .......................................................................17
LED Light Specification ........................................................................17
Wallach Colposcopes EMC Compliance Information..........................18
Guidance and Manufacturer’s Declaration.............................................18
Electromagnetic Emissions ..................................................................18
Electromagnetic Immunity ....................................................................19
Recommended Separation Distance .......................................................21
IMSC035-DFU • Rev. A • 6/14
1
Made in the USA
Read all safety information and instructions before using this product!
Cautions





DO NOT USE IN THE PRESENCE OF FLAMMABLE ANESTHETICS OR ELEVATED OXYGEN
LEVELS.
UNLOCK CASTERS BEFORE MOVING SCOPE OR UNIT MAY TIP OVER.
DO NOT OPERATE PRODUCT IF IT APPEARS TO HAVE BEEN DROPPED OR DAMAGED.
OBSERVE PRECAUTIONS FOR ELECTROSTATIC DISCHARGE (ESD) AND
ELECTROMAGNETIC INTERFERENCE (EMI) TO AND FROM OTHER EQUIPMENT.
LED RADIATION; DO NOT STARE DIRECTLY INTO BEAM.
The Wallach family of overhead swing arm colposcopes with Trulight feature Zoom and multi-step
magnification models on 4 or 5 leg rolling bases with locking casters.
ZoomScope™
The Wallach ZoomScope with Trulight is a multi-purpose microscope for colposcopy. The
ZoomScope with Trulight has a continuous Zoom range of magnification from 4.6x to 20x.
ASSEMBLY INSTRUCTIONS
A. Mobile Floorstand
CAUTION: BE SURE THE SYSTEM IS MOUNTED SECURELY IN PLACE TO AVOID
PERSONAL INJURY.
IMSC035-DFU • Rev. A • 6/14
2
Made in the USA
The stand has been sent unassembled for shipping purposes. Only one wrench is needed, and it is
taped to the base along with the appropriate hardware. (Allen wrench 5/16”; Wallach Part Number
WL111504) To complete assembly, place the scope column in the column mount hole so it is standing
upright. Carefully tip the entire unit on its side. Line up the hole underneath the base with the hole in
the bottom side of the column and insert the bolt. Tighten using the wrench supplied. A four-or fivelegged base is standard with the ZoomScope with Trulight.
B. Electronics Box and Suspension Arm
Place the electronics box and suspension arm assembly on the top of the column. The hole in the
bottom of the electronics box will fit over the column post. Be sure the white or black Teflon ring is
placed over the pin on the column before mounting.
IMSC035-DFU • Rev. A • 6/14
3
Made in the USA
C. Microscope Head
Place the microscope head into the retaining ring with ocular tubes pointed upwards. Hand-tighten the
thumbscrew. Remove protective caps from the diopter rings. Gently push the eyepieces into the
binocular tubes. Care should be taken to keep eyepieces in an upright position, as they will slip out if
the microscope head is turned upside down.
Caution: Do not tilt head all the way back as eyepieces can slide out of the binoculars
and become damaged.
D. Installation of Removable Handlebars for ZoomScope
1. Align the scope as you would to look through the Nikon head in a downward position.
2. The stainless steel mounting brackets are located on the left and right sides of the Nikon head
retaining ring.
3. The corresponding handles marked “L” (left) and “R” (right) should be inserted into the
mounting brackets. NOTE: The handles are marked on the solid end.
4. The holes in the middle of the retaining brackets allow for two positions. The handles can be
mounted either parallel or perpendicular to the microscope head retaining ring.
OPTICAL HEAD ADJUSTMENT
A. Adjustment
To use as an operating microscope, reach behind the fine focus knobs and loosen the locking knob for
the microscope head retaining ring. Tilt the retaining ring up towards you and retighten the locking
knob. Loosen the thumb screw holding the microscope head in place, rotate the head 180° and
retighten.
Caution: Care should be taken to keep eyepieces in an upright position, as they will slip out if
the microscope head is turned upside down.
B. Changing the Eyepieces
While holding the microscope head, gently slide the eyepieces from the binocular tubes. To replace,
gently push the eyepieces back into the binocular tubes assuring that they are fully seated.
NOTE: Do not touch the lenses when handling eyepieces. Eyepieces should be
cleaned the same way as any photographic lens.
IMSC035-DFU • Rev. A • 6/14
4
Made in the USA
C. Magnification
Final magnification is determined by multiplying the eyepiece power times the microscope body power
times the objective lens power. The Wallach ZoomScope with Trulight is normally shipped with 20x
eyepieces and .33x objective lens.
Therefore, at the lowest setting of the magnification power knob (0.7), the magnification
would be:
20 x 0.7 x .33x = 4.6x power
At the highest setting of the magnification power knob (3.0) the final magnification would be:
20 x 3.0 x .33x = 19.8x power
POWER ZOOM AND FOCUS
Directions for Attaching Optional Foot pedal (used for units purchased with power zoom & focus
features):
Attach by inserting male connector into female receptacle located at the bottom of the electronics box.
SCOPE OPERATION
1. Plug in power cord.
2. Turn ON (I) the master switch.
3. Turn on the white or green light using the switch located on the front of the unit.
4. Turn light illumination knob to appropriate light intensity. This can be adjusted at any time during
the procedure.
5. Unlock the casters when moving the colposcope. For transportation of the colposcope, place
colposcope head in lowest position to assure stability during transportation.
6. Position the ZoomScope; lock casters in place.
7. See “Focusing” instructions that follow.
FOCUSING THE ZOOMSCOPE WITH TRULIGHT
1. Turn both diopter rings on the binocular tubes until the end surface of each ring coincides with the
black engraved lines.
2. Looking into the eyepieces, set the distance between the oculars to conform to your interpupillary
distance by moving the binocular tubes so that both circular view fields are brought into
coincidence.
3. Set the zoom knob to 3x. (If power zoom is available, the footpedal should be used).
4. Adjust the fine focus rack to midway of travel. Position the head at approximately 305 mm (for
.33x objective lens) from the target to coarse focus. Rotate the fine focus knobs to bring the target
into focus. The fine focus knobs can be tightened or loosened to adjust travel ease by rotating
them in opposite directions. If power focus is available, the footpedal must be used for focusing
operations.
Do not re-adjust fine focus after a clear image is viewed at the 3x zoom magnification.
IMSC035-DFU • Rev. A • 6/14
5
Made in the USA
5. Rotate the zoom knob to 0.7x (Footpedal should be used where power zoom is available).
6. Close your right eye; adjust the left diopter ring to bring the target into focus. Close your left eye;
adjust the right diopter ring to bring the target into focus.
7. At this point, focusing has been completed. Steps 1 through 7 can be repeated for exact focusing
if desired. As long as the scope is not moved out of position, or the fine focus adjustment is not
moved, the target will keep its sharpness at all times regardless of the zoom magnification level.
VIDEO ZOOMSCOPE WITH TRULIGHT, USB
Sentech USB Camera Setup
1. Install Sentech Image Viewing Software (StCamSWare) onto laptop desktop. (See Quick Start
Guide IMSC031)
2. Attach Video ZoomScope microscope optical head to laptop via USB cable provided.
3. Turn on Colposcope
4. Double Click on the “STCamSWare” icon on the desktop
5. Using the cursor, choose “Options,” then “Settings”. A window will open at the bottom right of
screen.
6. Check the “Auto” boxes next to the Gain and Shutter features. (Mirror image should be set to
vertical.)
7. Click on the “Save” button, and then choose “Yes”.
8. Focus to get the desired image on the screen.
9. To capture the image on the screen, choose “Capture” and then “Snap Shot”.
10. A window will open to the right of the main image.
11. To save the image, click to “select” the image with your left mouse button. This will cause a “blue”
border to appear around the image of interest.
12. With the mouse over the image, click using the right mouse button and a menu will appear. Select
“Save”.
13. The image may be saved in one of four formats: Bitmap, TIFF, JPEG or PNG.
14. Complete the information as you would for any software program and save to a location of your
choice.
IMSC035-DFU • Rev. A • 6/14
6
Made in the US
TriScope™
The TriScope is a highly versatile triple magnification stereoscopic colposcope. A magnification of 8x,
13x, and 21x is obtained with the 3-step magnification changer. The field of view diameters are
24mm, 15mm, and 9mm. A vessel delineation filter (green light) is incorporated to provide clear
visualization of vascular patterns. The optical beam splitter permits the attachment of the coobservation tube and photographic accessories for documentation purposes, thereby extending the
capability of this instrument from routine gynecologic examinations to gynecologic research. The
image obtained through the accessory ports is identical to that viewed through the binocular tubes via
the optical beam splitter. Photographic documentation capabilities include video and digital
photography.
High power white light emitting diodes allow user to view images in pure white light. A green LED will
be used to pick up blood vessels. The TriScope is mounted on a 4 or 5-legged base for stability and
maneuverability.
ASSEMBLY INSTRUCTIONS
The TriScope has three parts. The following are easy assembly instructions for the new colposcope.
1. Optical Head with Eyepieces on the arm with Control Box
2. Mobile Floorstand
3. Column
The stand has been sent unassembled for shipping purposes. Assembly is not difficult. Only one
wrench is needed, and it is taped to the base along with the appropriate hardware. (Allen wrench
5/16”; Wallach Part Number WL111504) To complete assembly, place the scope column in the
column mount hole so it is standing upright. Carefully tip the entire unit on its side. Line up the hole
underneath the base with the hole in the bottom side of the column and insert the bolts. Tighten using
the wrench supplied.
Place the control box optical head and suspension arm assembly onto the top of the column. The hole
in the bottom of the control box will fit over the column post. Be sure the white Teflon ring is placed
over the pin on the column before mounting.
OPERATING INSTRUCTIONS
To operate the TriScope:
1. Set the Optical System to the desired height.
2. Plug the cord into a standard wall outlet.
3. The master power switch is located on the side panel of the control box assembly. This switch
turns the main power source ON or OFF.
4. The switch on the front panel turns the light ON or OFF. The light adjustment Illumination knob is
located on the front panel of the control box assembly. The light intensity is adjusted by the knob.
5. For transportation of the colposcope, place colposcope head in lowest position to assure stability
during transportation.
IMSC035-DFU • Rev. A • 6/14
7
Made in the USA
FOCUSING THE TRISCOPE
1. Set the binocular eyepieces to “0” and adjust them to the proper interpupillary distance.
2. Peering through the eyepieces, move the arm of the TriScope backward or forward to get a
“rough” focus on the target (12” or 300 mm from objective lens to target).
3. Focus at the highest magnification. Focusing at this magnification is extremely critical and leads to
perfect focusing for all other magnification levels. Set the fine focus by rotating the fine focus
knobs until the rack is at the midpoint. Thereafter, the physician only has to switch to another
magnification without the need to refocus the instrument. If the instrument is repositioned,
however, the procedure must be repeated.
4. To set the image of the target in each eye, turn the eyepieces themselves. (Notice that the
eyepieces are calibrated to help refocus the eyepiece setting next time.)
5. Focusing is complete.
ACCESSORIES
Your TriScope split beam colposcope is designed to provide the ultimate ease in colposcopic digital
photography. The complete system of photographic equipment for digital pictures has been created to
allow even the novice photographer to clearly document visual observations for patient files.
No special techniques are required and there is no need to dismount the camera when photography is
not intended. Camera focusing is achieved through the TriScope oculars.
Digital Camera Attachment
1. Remove camera lens cover. Attach the adaptor mounting ring to the camera by aligning the red
mark on the ring with the red dot on the camera lens mount. Then turn the ring until a click is
heard when attachment is secure.
2. Remove the black cap on the digital camera photo adaptor by loosening the stainless steel set
screw. Place the end of the adaptor mounting ring into the photo adaptor and retighten the set
screw.
3. Attach the digital camera photo adaptor to the colposcope accessory port. The camera may be
mounted on either the right or the left accessory port.
4. Remove the protective accessory port cap. Guide slots on the photo adaptor permit the
positioning of the camera. Align the slots in the photo adaptor with the guides on the adaptor ring.
Slide the adaptor ring over the photo adaptor and tighten gently in a counterclockwise direction.
DO NOT OVER TIGHTEN.
5. The camera is now ready for use.
Digital Photography
Refer to instruction manual for the digital camera.
Looking through the oculars, adjust the instrument for focus and composition. When the desired
image is obtained, press the shutter release button on the camera to make the exposure.
IMSC035-DFU • Rev. A • 6/14
8
Made in the USA
Teaching Tube
For teaching or co-observation, the teaching tube provides a second party viewing head as an optional
accessory.
The teaching tube may be mounted on either the right or left accessory port provided on the beam
splitter. Remove the protective accessory port cap. Guide slots on the teaching tube allow for
positioning of the unit. Align the slots on the teaching tube with the guides on the adaptor ring. Slide
the adaptor ring over the teaching tube and tighten gently in a counterclockwise direction. DO NOT
OVER TIGHTEN.
USB Video Attachment
There is a video camera C-Mount Adaptor available to attach any analog or USB camera. (Please
note that only one side of the C-Mount Adaptor can attach to the TriScope.)
The instructions are as follows:
1. Attach the mounting ring to the camera.
IMSC035-DFU • Rev. A • 6/14
9
Made in the USA
2. Attach the entire camera to the C-mount Adaptor.
3. Then attach the C-Mount Adaptor to the TriScope.
4. Plug in the S video cable if you have an analog camera. Next, plug in the power supply. Then
plug the power supply into the wall. For a USB camera, plug the USB cable into the camera and
the other end into the USB port on the laptop or PC.
5. After the C-Mount has been attached to the colposcope, the camera needs to be oriented so that
the image on the monitor is the same as that viewed through the optical head. On the C mount,
loosen the large silver knurled ring. Rotate the camera head until the image on the monitor is the
same as what is viewed through the optical head. Once it is aligned properly, rotate the knurled
ring clockwise until it is locked in a snug position.
IMSC035-DFU • Rev. A • 6/14
10
Made in the USA
ARM ADJUSTMENT
Your Wallach Colposcope with Trulight is adjusted and tested just prior to leaving the factory. The
colposcope arm may be moved into any position and should remain in place. However, further arm
adjustments may become necessary. A 5/64 Allen wrench is included.
For Arm Tightening Adjustment (see laminated instruction attached to pole)
1. Tighten Up & Down Motion of the Arm
Find set screws (two pair) on the long part of the arm. Tighten these set screws 1/8 turn at a time
with a 5/64 Allen wrench by turning the screws clockwise. The arm movement may be set to a
desired tension by using these screws. All retaining screws should be tightened the same amount
(refer to instruction card on column).
2. Tighten Back & Forth Motion of the Arm
Find set screws on the short part of the arm. These screws should be tightened 1/ 8 turn at a time
with a 5/64 Allen wrench by turning clockwise. The back and forth motion may be set to a desired
tension by using these screws. All set screws should be tightened the same amount.
Electrical
The Wallach Colposcope with Trulight requires a 100-240V ~ 50-60 Hz power source to operate. It is
supplied through a 2.5 meter medical grade detachable cord in standard 120 volt versions. For your
safety, assure that your electrical outlets meet code regulations. The master power switch is located
on the side panel of the electronics box assembly. This switch turns the main power source on or off.
The switch on the front panel turns the light from white to green and back. (The middle setting is for
“O”, the IEC symbol for OFF.) The knob on the front panel controls the light intensity.
Illumination
a. LED Light Frequency
b. Dominant Wave Length for Green Light Emitting Diode
Minimum value 530 nm (nanometers)
Maximum value 535 nm (nanometers)
Replacing the Fuses
1. Shut OFF (O) the master switch and unplug power cord.
2. The electronics box contains two fuses beneath the power socket.
IMSC035-DFU • Rev. A • 6/14
11
Made in the USA
3. To remove, pull out the drawer beneath the power socket.
4. Remove the blown fuse from the holder and replace with a 2 amp, 5 mm x 20 mm Fast Blow Fuse
5. Push the fuse holder back into the electronics box.
Moving the Colposcope with Trulight
To move the Colposcope with Trulight from room to room, release the locking casters, unplug the
power cord from the outlet and position the microscope head away from the direction of movement.
Grasp the column with one hand and the scope with the other and push the colposcope to its new
location. For added stability, it is best to position the suspension arm directly over any one of the legs
as it is being moved.
Positioning the Colposcope with Trulight
Set the Wallach Colposcope with Trulight in front of the examination table so that one leg is
perpendicular to the table and in line with the suspension arm. Each leg is equipped with a locking
caster. To lock the caster, push down. To unlock the caster, push up.
Maintenance
PRECAUTION: DO NOT IMMERSE EQUIPMENT COMPONENTS IN LIQUID; UNPLUG
BEFORE CLEANING; DRY BEFORE USE.
Clean the lenses and protective light covers with silicone-treated lens tissue paper ONLY. The
colposcope finish is a high-gloss enamel and may be wiped down with a disinfectant. Keep the
instrument clean and dust-free. When the colposcope is not in use, replace protective covers.
Warranty Information
Wallach Trulight products are warranted by Wallach Surgical Devices to be free from defects in
material and workmanship for a period of seven years. During this period, Wallach Surgical
Devices will, at its option and without charge, either repair or replace any part or assembly of
parts found to be defective in material and workmanship. Repairs are to be accomplished by a
Certified Wallach Surgical Devices Repair Technician. In the event that the unit is tampered
with by unauthorized personnel prior to the end of the warranty, the warranty is considered
NULL and VOID,
This warranty does not apply to the following:
1. Product which has been subject to misuse, abuse, negligence or accident.
2. Defects or damage directly or indirectly caused by installation or service of the product by
unauthorized personnel and/or the use of unauthorized replacement parts.
3. Improper use of cleaning methods or chemicals which damages equipment.
4. Peripheral equipment that is covered by the manufacturer’s warranty.
IMSC035-DFU • Rev. A • 6/14
12
Made in the USA
Service and Repair
In the event your Colposcope with Trulight becomes inoperative, please make the following checks
before calling the factory:
1. Check that the unit is plugged into a working wall receptacle.
2. Check for a blown fuse.
WARNING!
Remove AC Power from the colposcope before checking for a blown fuse.
If your colposcope is still inoperative, remove the unit from use, contact qualified factory service
personnel at (866)-928-3211.
If a repair is needed, equipment must be sanitized before it is returned to the factory and carefully
packaged in a protective carton. It is not necessary to ship the base and column unless there is a
problem with them. All shipments must be made via pre-paid parcel post or U.S. Mail. COD packages
will not be accepted. Return carton to:
SURGICAL DEVICES
Attention: Repair Department
95 Corporate Drive
Trumbull, CT 06611 USA
Phone: (203) 799-2000
Fax: (203) 799-2002
IMSC035-DFU • Rev. A • 6/14
13
Made in the USA
Explanation of Symbols
REF
SN
Reorder Number
Serial Number
Consult instructions for use
U.S. Federal law restricts this device
to sale by or on the order of a physician.
For professional use only
Product conforms to the Medical Device
Directive 93/42/EEC
EC REP
Authorized Representative in the
European Community.
Manufacturer
AC Main Power OFF
AC Main Power ON
Shock Hazard
Pinch Point
IMSC035-DFU • Rev. A • 6/14
14
Made in the USA
Specifications
ZOOMSCOPE WITH TRULIGHT SPECIFICATIONS
Overall height
160.02 cm
Height of column
Overall weight
101.6 cm (116.8 cm and 139.7 cm also
available)
27.9 kg (Basic ZoomScope without accessories)
Center of column to end of leg
39.37 cm
Center of column to center of
microscope with boom suspended
horizontally
Height of microscope from depressed
position of suspension to floor
50.80 cm
Power Requirements
100-120V/200-240V AC, 50/60 Hz, 100VA
Fused power input lamp
2.0 amps
Fuse Rating:
F2.0A/250V~
Power cord
2.44 meter medical grade power cord
with North American 120 VAC plug
Working Distance
285 mm
Dominant Wave Length for
Green Light Emitting Diode
Minimum value 525 nm (nanometers)
Maximum value 535 nm (nanometers)
IMSC035-DFU • Rev. A • 6/14
67.31 cm.
At extreme position of suspension: 116.8 cm
(with short column)
15
Made in the USA
TRISCOPE SPECIFICATIONS
Type
Warranty
Power Requirements
Mounting Systems
3-Step Magnification with beam splitter
7 Year
100-120V/200-240V AC, 50/60 Hz, 100VA
4 or 5-Leg Rolling Base (4 is standard)
Standard Optical Configurations
Objective Lens (Working Distance)
Total Magnification
Field of View
Depth of Field
Ocular (Eyepieces)
Diopter Adjustment
Interpupillary Range
Tilt of Viewing Head
Binocular Tube Design
Binocular Tube Lengths
Magnification Changer Factors
Vessel Delineation Filter
300mm
8x, 13x, & 21x
8.5x = 23.4mm, 13.6x =14.6mm,
21.3x = 9.4mm
8x =3.1mm, 13.6x =1.2mm,
21.3x = 0.9mm
16x Highpoint, with locking diopters
Independent adjustment with position
locking -6/+4
54mm to 80mm
59 degrees
Straight
160mm
1.0x, 1.6x, 2.5x
Yes
Illumination System
Illumination
Light Emitting Diodes (LED) (5000/7000
degrees Kelvin)
Green LED for blood vessel delineation.
Photographic Capabilities
Digital, Video
Yes
Options
Teaching Tube
IMSC035-DFU • Rev. A • 6/14
Yes
16
Made in the USA
For All Scope Colposcope Models
Classification
Model
Scope with Trulight Colposcopes




Safety Class
I
ALL models of Colposcopes have no Applied Parts.
Do not get fluid into the Colposcope. Should any liquid or solid object fall into the unit,
unplug the unit and call Technical Support (866) 928-3211.
The LED Model Colposcopes are suitable for continuous operation.
The LED Model Colposcopes are classified as normal equipment (IPX0) according to
protection against ingress of water.
Environment Conditions
Use:
Environmental Temperature:
Relative Humidity:
Air Pressure:
between +10 °C and +40 °C
between 10% and 90 %
between 700 hPa and 1060 hPa
Shipping and Storage:
Environmental Temperature:
Relative Humidity:
Air Pressure:
between +10 °C and +40 °C
between 10% and 90%
between 700 hPa and 1060 hPa
LED Light Specification
White LED:
Correlated Color Temperature
Rendering Index
Radiometric Power
Total Irradiance
6000K
70
80 mW
4.284 W/m2 at max intensity
Green LED:
Average Wavelength
Radiometric Power
Total Irradiance
IMSC035-DFU • Rev. A • 6/14
530 nM
80 mW
0.795 W/m2 at max intensity
17
Made in the USA
Wallach Colposcopes EMC Compliance Information


MEDICAL ELECTRICAL EQUIPMENT needs special precautions regarding EMC and needs
to be installed and put into service according to the EMC information provided in the
ACCOMPANYING DOCUMENTS.
Portable and mobile RF communications equipment can affect MEDICAL ELECTRICAL
EQUIPMENT.
Guidance and Manufacturer’s Declaration – Electromagnetic Emissions
The Wallach Colposcope is intended for use in the electromagnet environment specified below. The
customer or the end user of the Wallach Colposcope should assure that it is used in such an
environment.
Emissions Test
Compliance
RF emissions
Group 1
CISPR 11
Electromagnetic Enviroment- Guidance
Wallach Colposcopes use RF energy only for it internal function.
Therefore, its RF emissions are very low and are not likely to
cause any interference in nearby electronic equipment.
RF emissions
Class A
CISPR 11
Harmonic emissions
Class A
IEC 61000-3-2
Voltage fluctuations/
Flicker emissions
Wallach Colposcopes are suitable for use in all establishments,
including domestic establishments and those directly connected
to the public low-voltage power supply network that supplies
buildings used for domestic purposes.
Complies
IEC 61000-3-3
IMSC035-DFU • Rev. A • 6/14
18
Made in the USA
Guidance and Manufacturer’s Declaration – Electromagnetic
Immunity
The Wallach Colposcopes are intended for use in the electromagnet environment specified below.
The customer or the end user of the Wallach Colposcopes should assure that it is used in such an
environment.
IEC 60601
Test Level
Immunity Test
Electromagnetic
discharge (ESD)
Compliance Level
+6 kV contact
+6 kV contact
+8 kV air
+8 kV air
Electrical fast
transient/burst
+2 kV for power supply
lines
+2 kV for power
supply lines
IEC 61000-4-4
+1 kV for input/output
lines
+1 kV for
input/output lines
Surge
+1 kV differential mode
+1 kV differential
mode
IEC 61000-4-5
+2 kV common mode
IEC 61000-4-2
Electromagnetic Environmental Guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30%.
Mains power quality should be that
of a typical commercial or hospital
environment.
Mains power quality should be that
of a typical commercial or hospital
environment.
+2 kV common
mode
Voltage dips, short
interruptions and
voltage variations
on power supply
input lines
IEC 61000-4-11
Power frequency
(50/60 Hz)
magnetic field
< 5% UT
(> 95% dip in UT)
for 0.5 cycle
< 5% UT
(> 95% dip in UT)
for 0.5 cycle
40% UT
(60% dip in UT)
for 5 cycles
40% UT
(60 % dip in UT)
for 5 cycles
70% UT
(30% dip in UT)
for 25 cycles
70% UT
(30% dip in UT)
for 25 cycles
< 5% UT
(> 95% dip in UT)
for 5 sec
< 5% UT
(> 95% dip in UT)
for 5 sec
3 A/m
3 A/m
Mains power quality should be that
of a typical commercial or hospital
environment. If the user of the
Wallach Colposcope requires
continued operation during power
mains interruptions, it is
recommended that the Wallach
Colposcope be powered from an
uninterruptible power supply or a
battery.
Power frequency magnetic fields
should be at levels characteristic of
a typical location in a typical
commercial or hospital
environment.
IEC 61000-4-8
NOTE: UT is the a.c. mains voltage prior to application of the test level. In this case 230 V.
IMSC035-DFU • Rev. A • 6/14
19
Made in the USA
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity (continued)
Immunity
Test
IEC 60601
Test Level
Complianc
e Level
Electromagnetic Environmental – Guidance
[Note 1 and 2]
Portable and mobile RF communications equipment
should be used no closer to any part of the Wallach
Colposcope, including cables, than the recommended
separation distance calculated from the equation
applicable to the frequency of the transmitter.
Conducted RF
3 Vrms
IEC 61000-4-6
150 kHz to 80 MHz
Radiated RF
3 V/m
IEC 61000-4-3
80 MHz to 2.5 GHz
3V
3 V/m
Recommended separation distance
 3. 5 
d   P
 V1 
 3.5 
d    P 80 MHz to 800 MHz
 E1 
7
d    P 800 MHz to 2.5 GHz
 E1 
where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,a should
be less than the compliance level in each frequency
range.b
Interference may occur in the vicinity of equipment
marked with the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from
structures, objects and people.
a
b
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones
and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be
predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the measured field strength in
the location in which the Wallach Colposcope are used exceeds the applicable RF compliance level
above, the Wallach Colposcope should be observed to verify normal operation.
If abnormal performance is observed, additional measures may be necessary, such as reorienting or
relocating the Wallach Colposcope.
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
IMSC035-DFU • Rev. A • 6/14
20
Made in the USA
Recommended Separation Distance
This section discusses the Recommended Separation Distance between portable and mobile RF
communications equipment and the Wallach Colposcopes.
The Wallach Colposcopes are intended for use in an electromagnetic environment in which radiated
RF disturbances are controlled. The customer or the user of the Wallach Colposcopes can help
prevent electromagnetic interference by maintaining a minimum distance between portable and mobile
RF communications equipment (transmitters) and the Wallach Colposcopes as recommended below,
according to the maximum output power of the communications equipment.
Separation distance according to frequency of transmitter
(Meters) [Note 1 and 2]
Rated maximum output
power of transmitter
(Watts)
0.01
0.1
1
10
100
150 kHz to 80 MHz
80 MHz to 800 MHz
 3.5 
d   P
 v1 
 3.5 
d   P
 E1 
0.1167
0.3689
1.1667
3.6894
11.667
0.1167
0.3689
1.1667
3.6894
11.667
800 MHz to 2.5
GHz
7
d  P
 E1 
0.2333
0.7379
2.3333
7.3789
23.333
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in meters (m) can be estimated using the equation applicable to the frequency of the
transmitter, where P is the maximum output rating of the transmitter in watts (W) according to the
transmitter manufacturer.
For the Wallach Colposcopes:
v1 = 3 Vrms
E1 = 3 V/m
NOTE 1:
At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2:
These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
IMSC035-DFU • Rev. A • 6/14
21
Made in the USA
This page left blank intentionally
IMSC035-DFU • Rev. A • 6/14
Made in the USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement