Tender Document
OFFICE OF THE MISSION DIRECTOR
NATIONAL RURAL HEALTH MISSION, ASSAM
SAIKIA COMMERCIAL COMPLEX, SRINAGAR PATH, CHRISTIANBASTI,
G.S ROAD, GUWHATI 781005
TENDER FOR SUPPLY OF HOSPITAL FURNITURE, FIXTURES,
EQUIPMENTS & INSTRUMENTS
(NATIONAL COMPETITIVE BIDDING)
OFFICE OF THE MISSION DIRECTOR
NATIONAL RURAL HEALTH MISSION, ASSAM
SAIKIA COMMERCIAL COMPLEX, SRINAGAR PATH, CHRISTIANBASTI,
G.S ROAD, GUWHATI 781005
Website : www. nrhmassam.in
e-mail : misnrhm.assam@gmail.com
TENDER FOR SUPPLY OF HOSPITAL FURNITURE, FIXTURES, EQUIPMENTS & INSTRUMENTS
(NATIONAL COMPETITIVE BIDDING)
TENDER NO:NRHM/PROC/HOS-EQP/1930/2013-14/39260 Date: 23/12/2013
Date of sale of Tender Document
: 24/12/2013
Last Date and Time of receipt of Tender
: 23/01/2014
till 2 pm
Pre Bid Meeting
: 08/01/2014
at 4 pm
Date and Time of opening Tender
: 23/01/2014
at 3 pm
Place of opening Tender.
:
Office of the Mission
Director, National Rural
Health
Mission,
Saikia
Commercial
Complex,
Srinagar
Path,
Christianbasti, G.S Road,
Guwahati-781005, Assam.
Address for Communication
:
Mission Director, National
Rural Health Mission,
Saikia Commercial Complex,
Srinagar Path,
Christianbasti, G.S Road,
Guwahati-781005, Assam.
Cost of Tender Documents in Demand Draft
:
Rs. 2000/-(Rupees Two
Thousand) only in the form
of Demand Draft in favour
of “State Health Society,
Assam”
OFFICE OF THE MISSION DIRECTOR
National Rural Health Mission, Assam
SAIKIA COMMERCIAL COMPLEX, SRINAGAR PATH, CHRISTIANBASTI,
G.S ROAD, GUWHATI 781005
TENDER FOR THE SUPPLY OF HOSPITAL FURNITURE, FIXTURES, EQUIPMENTS & INSTRUMENTS
Sealed tenders in Two Bid System (Technical Bid & Price Bid in separate sealed envelopes)
affixing court fee stamp of Rs 8.25 (or IPO of Rs 10/- for bidders located outside the State of
Assam) only, are invited from manufacturers or authorized distributors/dealers for “Supply
of Hospital Furniture, Fixtures, Equipments & Instruments” to health institutions in different
districts of Assam on turnkey basis.
1.
LAST DATE FOR RECEIPT OF TENDERS.
Sealed Tenders in two separate covers {Technical bid (Cover “A”) and Price Bid
(Cover “B”)} will be received up to 23-01-2014 till 2 PM by the Mission Director,
National Rural Health Mission, Saikia Commercial Complex, Srinagar path,
Christianbasti, G S Road, Guwahati-781005, Assam
2.
IMPORTANT NOTES:
a) The bidder shall quote prices in Indian Rupees only, on FOR destination basis.
b) Delivery of the ordered items shall be affected at District Drug Ware Houses or the
designated Health Institutions spread over 27 districts in Assam.
c) Arrangement of Road Permits for despatch of consignments shall be the
responsibility of the successful bidder (s).
3.
PRE-BID MEETING
A Pre- Bid meeting with all the intending bidders will be held at Conference Hall of
NRHM Office on 08/01/2014 at 4pm.
4.
ELIGIBILITY CRITERIA
A.
Bidder shall either be a manufacturer or a distributor/dealer having
experience of supplying Hospital Furniture & Fixture/Medical
Equipments/Instruments to Govt. Organizations.
B.
Average Annual turnover of the bidder (who is not a manufacturer) in the last
three financial years i.e. 2010-11, 2011-12, 2012-13 from sales of Hospital
Furniture & Fixtures/Medical Equipments/Instruments shall not be less than
Rs 11 (Eleven) Crores.
C.
Manufacturer participating as bidder or manufacturer from whom the
Hospital Furniture & Fixture/Medical Equipments/Instruments would be
sourced by the dealer should have an average Annual Turnover of Rs 15
(Fifteen) Crores in the last 3 financial years i.e. 2010-11, 2011-12, 2012-13.
However, for manufacturers of Hollow Wares, the average Annual Turnover
in the last three financial years shall not be less than Rs 1 (One) Crore.
5.
D.
Bidder should have at least 3(Three) years Market Standing as supplier of
Hospital Furniture & Fixture/Medical Equipments/Instruments.
E.
Manufacturers of Hospital Equipments/Instruments shall have valid CE/US
FDA Certification and also have valid ISO 9001:2000/ISO 14001:2004
certificates. Manufacturers of Hospital Furniture & Fixtures shall have valid
OHSAS 18001:2007 certificate as well as ISO 9001:2000/ISO 14001:2004
certificates. Manufacturers of Surgical Hollow Wares shall have valid ISO
9001:2000 certificate. All such certificates should have been obtained and
valid in the past 3 years.
F.
Bidder shall have experience in supply & installation of Hospital Furniture &
Fixture/Medical Equipments/Instruments in the last 3 (three) financial years
and value of a single order for such items during this period should be at least
Rs2.00 Crores.
G.
Bidder should have experience & knowledge of modes of packing,
distribution & transportation of such items under any weather conditions.
H.
Bidder who has been blacklisted either by the Tender Inviting Authority or by
any State Government or Central Government Organization will not be
allowed to participate in the tender during the period of blacklisting.
GENERAL CONDITIONS.
(I)
There are six groups of items in the tender (Groups A, B, C, D, E & F). A bidder
must quote for all the items in a particular Group as indicated in the bid
document. In case, a bidder does not quote for one or more items in a
particular Group, the bid for that Group shall be considered incomplete and
shall be liable for rejection.
(II)
A bidder may quote for any or all the Groups. A bidder quoting rates for
supply of items in Group A, B, C & D must also quote for Comprehensive
Maintenance Contract price of such items for a period of 3 years.
(III)
The quantity of each item indicated in the bid document is tentative and
subject to change depending on actual requirement.
(IV)
Tender documents may be obtained from the office of Tender Inviting Authority
during office hours on payment of Rs 2000/-(non – refundable) in the form of
Demand Draft drawn in favour of “ State Health Society, Assam” payable at
Guwahati The tender documents may also be downloaded from the official
website- www.nrhmassam.in.The bidder downloading the Bid document
from the website will be required to deposit Rs 2000/-(non – refundable) in
the form of Demand Draft drawn in favour of “ State Health Society, Assam”
payable at Guwahati while submitting the Tender. Tender without the fee of
Rs 2000/- will not be accepted.
(V)
All tenders must be accompanied by Earnest Money Deposit as specified in the
relevant clause of the bid document.
6.
(VI)
Tenders will be opened in the presence of bidders / authorized representatives
who choose to attend on the specified date and time as stipulated in the bid
document.
(VII)
At any time prior to the date of submission of tender, the Tender Inviting
Authority may, for any reason, whether on his own initiative or in response to a
clarification requested by a prospective Bidder, modify the tender document by
an amendment. All prospective bidders who have received the tender
document will be notified of the amendment and that will be binding on them.
In order to provide reasonable time to take the amendment into account in
preparing their bid, Tender Inviting Authority may at its discretion, extend the
date and time for submission of tenders.
(VIII)
Interested eligible bidders may obtain further information from the office of the
Tender Inviting Authority.
(IX)
Price Preference/ Purchase Preference to PSUs / SSI Units shall not be
applicable.
(X)
When a bidder specifies name of the manufacturers of different products in the
format at Annexure VIII, all required documents (specifically Average Annual
Turnover Statement & quality certificates) of each manufacturer should
invariably be furnished, failing which the bid would be summarily rejected.
TECHNO-COMMERCIAL BID - COVER “A”
The Bidder should furnish the following documents/charges in a separate cover
hereinafter called "Cover A".
A.
Court Fee Stamp/IPO and Tender Document Fee
Court fee stamp of Rs 8.25 (or IPO of Rs 10/- for bidders located outside the State of
Assam). Tender document fee of Rs 2000.00 in the form of a Demand Draft in favour
of “State Health Society, Assam” payable at Guwahati
B.
Earnest Money Deposit (EMD)
Earnest Money Deposit amounting to Rs 31.50 Lakhs (Rupees Thirty One
Lakhs Fifty Thousand) only in the form of Demand Draft/Banker’s Cheque/Bank
Guarantee favoring “State Health Society, Assam”. In case of BG, the same
shall be valid for 120 days. Earnest Money Deposit in any other form will not
be accepted. Earnest Money Deposit will not earn any interest. The Earnest
Money Deposit of the successful Bidder may, at the discretion of Tender Inviting
Authority be adjusted towards the Security Deposit payable by the Bidder.
C.
Constitution of Company of Bidder:
Documentary evidence regarding constitution of the company /concern such as
Memorandum & Articles of Association, Partnership Deed etc. with details like
Name, Address, Telephone Number, Fax Number, E-mail Address of the firm
with names of the Managing Director / Partners / Proprietor.
D.
Manufacturing License of Principal Manufacturer:
Attested photocopy of valid Manufacturing License duly issued by the
Licensing Authority for the products quoted.
E.
Import License of Bidder:
Attested copy of Import License, if the products are imported. The license must
have been renewed up to date. A copy of a valid license for the sale of the
products imported by the firm issued by the licensing authority shall also be
enclosed.
F.
Power of Attorney of Bidder:
Attested copy of instruments such as Power of Attorney, Resolution of Board
etc., authorizing an officer of the bidding firm to submit their bids. Such
authorized officer should sign the bid documents.
G.
Undertaking of Bidder:
Undertaking in the form at Annexure-I
H.
Manufacturer’s Authorization
Authorization letters from all the manufacturers concerned in the format at
Annexure -II. Bids without authorization letters will be disqualified.
I.
J.
CE/US FDA, ISO, OHSAS Certificates
i)
Attested copies of valid CE/US FDA Certificate (only of manufacturers
whose products have been offered) for Hospital Equipments and
Instruments.
ii)
Attested copies of valid ISO 9001:2000/ISO 14001:2004 certificates (of
manufacturers whose products have been offered) for Hospital
Equipments and Instruments
iii)
Attested copies of valid OHSAS 18001:2007 certificate (of manufacturers
whose products have been offered) for Hospital & Office Furniture and
Fixtures.
iv)
Attested copies of valid ISO 9001:2000/ISO 14001:2004 certificate (of
manufacturers whose products have been offered) for Hospital & Office
Furniture and Fixtures.
v)
Attested copies of valid ISO 9001:2000 certificate (of manufacturers
whose products have been offered) for Surgical Hollow Wares.
Annual Turnover
Annual turnover statement from sales of Hospital Furniture/Fixtures/
Equipments/Instruments for 3 years i.e., 2010-11, 2011-12 & 2012-13 in the
format given in Annexure-III A and Annexure-III B certified by the
Auditor/Chartered Accountant. It is to be noted that such statement of both
the bidder and the manufacturer (in case the bidder is not a manufacturer)
must be submitted.
K.
I.
L.
Execution of similar contracts of Bidder:
Details of supplies (Hospital Furniture & Fixtures/Equipments & Instruments)
made during the last 3 financial years with summary of Purchase Orders and
Performance Certificates issued by clients in the specified format (Refer
Annexure IV). Items supplied to Govt. institutions and to programs sponsored
by WHO, UNICEF etc., if any, during the last 3 years should be highlighted.
Copies of orders/performance certificates including one single order of value
at least Rs 2.00 Crores executed during the last 3 years should be submitted.
Sales Tax Clearance Certificate of Bidder:
Sales Tax Clearance certificate, as on 31st March of last financial year (as per
format at Annexure-V.
M.
Undertaking for providing of logo of Bidder:
Undertaking (as per Annexure-VI) for embossment of NRHM Assam logo on all
items.
N.
Details of Manufacturing Unit of manufacturer
Details of Manufacturing Unit as per Annexure-VII. The details containing the
name & address of the premises where the items are actually manufactured.
O.
List of Items Quoted /Technical Compliance Statement
The List of items quoted shall be furnished as per Annexure – VIII A
(separately for each Group). The list shall specifically indicate manufacturer’s
name along with warranty period offered for each item. Technical
Compliance Statement should also be submitted as per Annexure – VIII B
(separately for each Group).
P.
Undertaking on Fraud & Corruption of Bidder:
Undertaking on fraud and corruption in the format at Annexure-IX
Q.
Agreed Terms & Conditions of Bidder:
Agreed Terms & Conditions as per Annexure X.
R.
Signature & Seal on each page
The tender document signed by the Bidder in all pages with office seal.
S.
Checklist of documents
A Checklist (Annexure-XI) for the list of documents enclosed with their page
number. The documents should be serially arranged as per this Annexure-XI
and should be securely tied or bound.
The above documents should be sealed in a separate cover super scribed as
"TECHNICAL BID, COVER “A” (TENDER FOR SUPPLY OF HOSPITAL FURNITURE,
EQUIPMENTS ETC DUE ON 23/01/2014)”and addressed to the Mission Director,
National Rural Health Mission, Assam. Saikia Commercial Complex, Srinagar Path,
Christian Basti, G S Road, Guwahati-781005
7.
PRICE BID - COVER”B”
Cover “B” shall contain the Price Bids separately for Group A, Group B, Group
(C), Group (D), Group (E) & Group (F) in the formats at Annexure XII (A),
Annexure XII (B), Annexure XII (C), Annexure XII (D), Annexure XII (E), Annexure
XII (F) respectively of the Tender.
A.
Signature & Seal on each Page
Each page of the Price Bid should be duly signed by the Bidder affixing the
office seal.
B.
Signature on corrections
Bid should be typewritten and every correction in the bid should be attested
with full signature by the Bidder, failing which the bid will be ineligible.
Corrections done with correction fluid should also be duly attested.
C.
Items Quoted & Rates
The Bidder shall fill up the Annexure XII (A), Annexure XII (B), Annexure XII (C),
Annexure XII (D), Annexure XII (E), Annexure XII (F) for items quoted.
D.
Landed Cost
The rate quoted per unit or landed price in Annexure-XII shall be inclusive of
excise duty, sales tax, packaging charge, freight, Insurance etc. The
component of VAT/Sales Tax should also be shown separately.
E.
Unit Size/ Rate
The rate quoted in Annexure-XII (A), (B), (C), (D), (E) & (F) should be for a
unit and given specification. The Bidder is not permitted to change / alter
specification or unit size given in the Annexure-XIII.
The above documents should be sealed in a separate cover superscribed as
"PRICE BID, COVER “B” (TENDER FOR SUPPLY OF HOSPITAL FURNITURE,
EQUIPMENTS ETC DUE ON
23/01/2014)” and addressed to the Mission
Director, National Rural Health Mission, Assam. Saikia Commercial Complex,
Srinagar Path, Christian Basti, G S Road, Guwahati-781005
The two separately sealed covers {Technical bid (Cover “A”) and Price Bid (Cover “B”)}
shall be placed together inside another cover which shall be sealed and superscribed as
“TENDER FOR SUPPLY OF HOSPITAL
FURNITURE, EQUIPMENTS ETC DUE ON
23/01/2014” and addressed to the Mission Director, National Rural Health Mission,
Assam. Saikia Commercial Complex, Srinagar, G S Road, Guwahati-781005
8.
9.
OPENING OF COVER “A” AND COVER “B” OF TENDER
A.
All bidders are entitled to be present at the date and time of opening of
Technical Bid - Cover “A”.
B.
Only those bidders whose Technical Bids are found to be acceptable after
technical and commercial evaluation will be invited to be present at the date
and time of opening of Price Bid - Cover “B” of the tender. The price bids of
tenderers not found technically qualified shall not be opened.
VALIDITY OF BID:
Bids shall remain valid for acceptance for a period of 90 days after opening of Technical
Bid i.e. Cover ‘A’. Bids with shorter validity shall be rejected. Purchaser may solicit
bidders consent to an extension of validity period. A bidder may refuse extension
request without forfeiting the EMD.
10.
VALIDITY OF OFFER OF SUCCESSFUL BIDDER:
The validity of offer of the successful bidder shall be at least 02(two) years from the
date of finalization of the order and the successful bidder will be bound to supply the
items at agreed rates and terms during this period. This validity period may be
further extended with mutual consent.
11.
OTHER CONDITIONS
A. Item Details & Quantity
Specifications & Details of Items are shown in Annexure-XIII (A), (B), (C), (D),
(E) & (F). The quantity mentioned is only the tentative requirement and may
increase or decrease as per requirement of Tender Inviting Authority. The
rates quoted should not vary with the quantum of the order or the
destination.
B. Firm Rates
Firm Rates (inclusive of Excise Duty, Sales Tax, transportation, insurance,
PACKAGING/INSTALLATION & TRAINING CHARGES AT SITE and any incidental
charges) should be quoted for each of the required Hospital items on door
delivery basis according to the units ordered. Tender for supply of Hospital
items with conditional/variable rates shall not be accepted. Handling,
clearing, transport charges etc., will not be paid separately. The delivery
should be made as stipulated in the purchase order placed with the
successful bidders. The rates quoted and accepted will be binding on the
Bidder for the stipulated period and any increase in the price will not be
entertained till completion of the tender period.
C. Unit Rate & Total Value
Each bid must contain not only the unit rate but also the total value of each
item quoted for supply in the respective columns. The aggregate value of all
the items quoted in the tender shall also be furnished.
D. Controlled Price/MRP
The price quoted by the bidders shall not, in any case, exceed the controlled
price, if any, fixed by the Government and the Maximum Retail Price (MRP).
During the period of contract with the successful bidder, if the price of any
item is reduced due to any reason including any Law or Act of the
Central/State Government, the bidder shall be statutorily bound to intimate
the reduced rates immediately to the Tender Inviting Authority and shall
charge the reduced rates. The Tender Inviting Authority is empowered to
unilaterally effect such reduction as is necessary in rates, in case the bidder
fails to notify or fail to agree to such reduction in rates.
E. No Revision/Correction of Rates
No Bidder shall be allowed at any time on any ground whatsoever to claim
revision or modification in the rates quoted by him. Representation to make
correction in the tender documents on the ground of clerical error,
typographical error, etc., committed by the bidders in the Bids shall not be
entertained after submission of the bids.
F. Firm Delivery Schedule
Firm delivery schedule shall be mentioned in the bid. Cross conditions such as
“SUBJECT TO AVAILABILITY” “SUPPLIES WILL BE MADE AS AND WHEN
SUPPLIES ARE RECEIVED” etc., will not be considered under any
circumstances and the tenders of those who have given such conditions shall
be treated as incomplete and will be summarily rejected.
G. Execution of Order
Unless otherwise specified, supplies should be made directly by the
successful bidder and not through any other agency.
H. Inspection
Tender Inviting Authority or his authorized representative has the right to
inspect the factories of bidders, at any point of time and also has the right to
reject the tender or terminate / cancel the orders, based on adverse reports
brought out during such inspections. The Bidder shall extend all facilities to
the team to enable them to inspect the manufacturing process, quality
control measures adopted etc., in the manufacture of the items
quoted/ordered.
12.
ACCEPTANCE OF TENDER
A.
Tender Evaluation
Tenders will be evaluated with reference to technical and commercial
parameters to determine the technically qualified bidders for all Groups. The
technically qualified bidders for Group E items shall have to demonstrate the
following products for inspection and final assessment of quality:
“Labour Table, Examination Couch, Hospital Bed with Mattress, Hydraulic OT
Table, Instrument Cabinet, Semi Fowler Bed, Bedside Locker, Foot Step
(Double), Mayo’s Instrument Trolley, Field Type OT Table, Instrument Trolley”
In the event any of the above products demonstrated by a technically
qualified bidder in Group E is found to be deficient in terms of quality, the
offer of such bidder shall be declared as technically not acceptable. Based on
such assessment the final list of technically qualified bidders for Group E
items shall be drawn up.
Price Bids of technically qualified bidders will be evaluated with reference to
the quoted rates (landed price of each item). Conditional discounts shall not
be taken into account for price comparison. The total value of each item in a
particular group will be added to determine the overall lowest price. The
bidder quoting the overall lowest price in a particular Group shall be ranked
as the L1 bidder for that group.
B.
Right to Reject Tender
Tender Inviting Authority reserves the right to accept the tender or to reject
the whole tender for the supply of all items of Hospital Furniture, Fixtures,
Equipments & Instruments tendered at any point of time without assigning
any reason.
C.
Tender Acceptance
The acceptance of the tenders will be communicated to the successful
bidders in writing.
13.
AGREEMENT
The successful Bidder shall execute an agreement in the form at Annexure XIV
on a non-judicial stamp paper of value of Rs.100/- (stamp duty to be paid by the
Bidder) within 10 days from the date of the intimation from Tender Inviting
Authority informing that his tender has been accepted.
14.
NON ASSIGNMENT
The Bidder shall not, at any time, assign, sub-let or make over the contract or
the benefit thereof or any part thereof to any person or persons, whatsoever.
15.
COMMUNICATION
All notices or communications relating to or arising out of an agreement or
any of the terms thereof shall be considered duly served on or given to the
Bidder if delivered to him or left at his premises, places of business or abode.
16.
SECURITY DEPOSIT
The successful bidder, within 10 days of signing of the agreement, shall be
required to submit Security Deposit of 5 % of the order value in the form of
bank guarantee from any Indian scheduled bank in favour of the Tender
Inviting Authority valid for the entire warranty period. However, if the
supplier fails to execute the order or fails to perform the services as per
agreement, in addition to other penal actions, the bank guarantee shall be
encashed and the amount will be forfeited.
17.
SUPPLY & SERVICE CONDITIONS
A.
Purchase Order
Purchase order will be placed on the successful Bidder at the discretion of the
Tender Inviting Authority.
B.
Specifications & Quality
The items supplied by the successful Bidder shall be of the best quality and
shall comply with the specifications, stipulations and conditions specified at
Annexure-XIII (A), (B), ( C), (D), (E) & (F)
C.
Warranty Provisions
The successful bidder (Supplier) warrants that the goods supplied under the
contract/purchase order are new, unused, or the most recent of current
models and incorporate all recent improvements in design and materials
unless provided otherwise in the contract. The Supplier further warrants that
the goods supplied under the contract shall have no defect arising from
design, materials or workmanship or from any act or omission of the supplier
that may develop under normal use of the supplied goods.
i. The warranty shall be valid for the period mentioned in the Technical
Specification.
ii. Up gradation of all software shall be done free of cost during the warranty
period.
iii. The warranty should be as per the period mentioned in the Technical
Specification.
iv. The Tender Inviting Authority (Purchaser) shall notify the supplier in writing
of any claims arising under this warranty.
v. Upon receipt of such notice, the supplier shall, with all reasonable speed,
repair or replace the defective goods or parts thereof, free of cost at the
ultimate destination. The Supplier shall take over the replaced parts/goods at
the time of their replacement. No claim whatsoever shall lie on the
Purchaser for the replaced parts/goods thereafter.
vi. If the Supplier, having been notified, fails to remedy the defect(s) within a
reasonable period, the Purchaser may proceed to take such remedial action
as may be necessary, at the Supplier‘s risk and expense and without
prejudice to any other rights which the Purchaser may have against the
Supplier under the contract.
vii. The warranty for defective parts will begin de novo from the date of
replacement. Supplier will pay taxes/duties and all expenses up to the
destination for the replaced part.
viii. During the warranty period, the desired uptime of 95% of 365 days on a 24
hours basis shall be ensured.
i.
Delivery Period
The supply should commence within 30 (thirty) days from the date of order
and should be completed within 90 (days) maximum, unless otherwise
specified in the order.
ii.
Delivery Point/Destination
The items shall be delivered at the District Drug Ware Houses or Health
Institutions in different districts of Assam as per the list furnished along with the
order or according to instructions given separately with reference to the order.
iii.
iv.
Penalty for Delayed Delivery
(i)
In case there is delay in delivery beyond the stipulated period as
mentioned in the purchase order, there shall be reduction in price @
0.5% of the value of delayed goods per week of delay or part thereof
subject to a maximum of 10% of the total order value.
(ii)
Once the maximum price reduction is reached, termination of the
contract may be considered. Non-performance of the contract
provisions shall make the successful bidder liable to be disqualified to
participate in any tender for the next 5 years, in addition to forfeiture
of Security Deposit and other penal actions.
Alternative Purchase
If the successful Bidder fails to execute the order within the stipulated time,
the Tender Inviting Authority will be at liberty to make alternative
arrangements for purchase of the items, from any other source or from the
open market, at the risk and cost of the supplier. This would be in addition to
any other penalties including forfeiture of security deposit.
G.
Shortage and Damage
It shall be the responsibility of the successful Bidder for any
shortages/damages at the time of receipt in Warehouse/Institution. Tender
Inviting Authority is not responsible for the items received, for which no
order is placed.
G.
Comprehensive Maintenance
The successful bidder (Supplier) for items in Group A, Group B, Group C &
Group D shall provide post warranty Comprehensive Annual Maintenance
Contract (CAMC) service for a period 3 years from the date the warranty is
over. The CAMC amount shall include cost of labour, spare parts and
consumables required for repair and maintenance of equipments. The scope
of work during the CAMC period shall include, inter-alia, the following:
i)
ii)
iii)
iv)
18.
To ensure 95 % uptime of the equipments.
To upgrade software free of cost.
To undertake 4 preventive maintenance service in a year.
To attend to breakdown calls within 24 hours of reporting a fault.
FORCE MAJUERE
The above conditions of delivery period, price reduction etc. are subject to
force majeure conditions which are beyond the control of the supplier, do
not involve fault or negligence of the supplier and are not anticipated. Such
events may include but are not limited to riots, mutinies, war, fire, storm,
tempest, flood, earthquakes, epidemics, or other exceptional causes like
quarantine restrictions, freight embargoes. On specific request made by the
bidder the time period of supply may be extended by the purchaser at his
discretion for such period as may be considered reasonable. However, the
condition shall not include scarcity of raw materials, power cut, labour
dispute, failure of sub-vendor and increase in cost of raw material.
19.
FRAUD & CORRUPTION:
The bidders, suppliers & contractors shall observe the highest standard of
ethics during bidding and during performance of the contract. For the
purposes of this provision, the following acts shall be considered as corrupt
and / or fraudulent practices 1.
“Corrupt Practice” means offering, giving, receiving, or soliciting
directly or indirectly, of anything of value to influence the action of an
official in the procurement process or in contract execution.
2.
“Fraudulent Practice” means misrepresentation or omission of facts in
execution of contract.
3.
“Collusive practice” means a scheme or arrangement between two or
more bidders, with or without the knowledge of the purchaser,
designed to establish bid prices at artificial, non-competitive level.
4.
“Coercive Practice” means harming or threatening to harm, directly or
indirectly, persons or their property to influence their participation in
a procurement process or in execution of a contract.
During the process of evaluation of a bid or proposal for award of a contract,
if it is detected that a bidder directly or through agent has engaged in
corrupt, fraudulent, collusive or coercive practice in competing for the
contract in question, then a) the bid shall be rejected and b) declare the firm
ineligible for a specific period or indefinitely to participate in a bidding
process. However, if any such practice is detected at any subsequent stage or
during execution of the contract, the Tender Inviting Authority will exercise
the right to cancel the contract and make suitable alternative arrangement at
the risk and cost of such offending bidder.
20.
LOCAL CONDITIONS:
It will be imperative on each bidder to fully acquaint himself of all local
conditions and factors that would have any effect on performance of the
Contract. The Tender Inviting Authority shall not entertain any request for
clarifications from the bidder regarding such local conditions nor shall accept
any offer conditional to the local factors. No request for any change of price
or extension of time schedule of delivery of goods shall be entertained after
acceptance of bids.
21.
22.
LOGOGRAMS
A.
Tenders for the supply for furniture, equipments etc., shall be considered
only if the Bidder gives undertaking in his tender that the items will be
supplied with the logogram either printed or embossed or affixed as
specified.
B.
Failure to supply furniture, equipments etc., without the logogram will be
treated as breach of the terms of agreement.
PACKING
A.
B.
24.
Packing should be sound and be able to prevent damage or deterioration during
transit.
In the event the items supplied are found to be damaged or defective the
Tender Inviting Authority will be at liberty to make alternative purchase of the
items for which the Purchase orders have been placed from any other source or
from the open market at the risk and the cost of the supplier.
PAYMENT PROVISIONS
Payments towards the supply of items will be made strictly as per rules of the Tender
Inviting Authority. Full payment will be released only after completion of
supply/installation of entire ordered quantities. The payments for CAMC service will
be made on yearly basis after satisfactory performance of service each year.
A.
On completion of supply of supplied quantities, invoices with challans along
with installation reports (certified by the Head of the Health Institution) and
warranty certificates should be submitted in triplicate, addressed to the
Tender Inviting Authority. For payment towards CAMC, invoices along with
quarterly service reports (certified by the Joint Director, Health Service of the
district or an authorized official) should be submitted in triplicate, addressed
to the Tender Inviting Authority.
B.
If at any time during the period of contract, the price of tendered items is
reduced or brought down by any law or Act of the Central or State
Government or by the Bidder himself, the Bidder shall be bound to inform
Tender Inviting Authority immediately about such reduction in the contracted
prices. Tender Inviting Authority is empowered to unilaterally effect such
reduction as is necessary in rates in case the Bidder fails to notify or fails to
agree to such reduction in rates.
C.
In case of any enhancement in excise duty/ Tax due to notification of the
Government after the date of submission of tenders and during the validity
period of contract, the quantum of additional excise duty so levied will be
allowed to be charged extra as a separate item without any change in price
structure of the items approved under the tender. For claiming the additional
cost on account of the increase in excise duty, the bidder should produce a
letter from the concerned Excise Authority for having paid additional Excise
Duty on the goods supplied to Tender Inviting Authority and also must claim
the same in the invoice separately.
25.
D.
Tender Inviting Authority has every right to receive supply even after expiry
of contractual delivery date and in such case; price reduction as specified
under Clause No. 17 E will be applicable.
E.
If the supply is received in damaged condition it shall not be accepted. In
case of damage in the packing, the supply will be accepted only after levying
penalty as decided by the Tender Inviting Authority on the total value of
supply to that particular warehouse/institution.
ANNULMENT OF AWARD, FORFEITURE OF SECURITY DEPOSIT & FRESH AWARD
Failure of the successful bidder to comply with the requirements of signing of
agreement and / or submission of performance security within the time
schedule as stipulated above shall constitute sufficient grounds for the
annulment of the award and forfeiture of the bid security/EMD. Under such a
situation, the proposal may be reviewed for award of the contract on the
next lowest evaluated technically qualified bidder or go for a fresh bid
depending on the circumstance. In case it is decided to go for the next lowest
bidder, negotiation may be considered to bring down their price nearer to
the originally evaluated lowest bidder.
26.
NON CONFORMANCE, TERMINATION & PENALTIES
A.
If the items do not conform to specifications, the same shall be taken back by
the supplier at the supplier’s cost within a period of 30 days of the receipt of
the letter/notice from the Tender Inviting Authority. If the supplier fails to
take back the items within the stipulated time, the Tender Inviting Authority
will have the right to dispose-off such ITEMS NOT CONFORMING TO
SPECIFICATIONS. Tender Inviting Authority may also levy storage charge
calculated at the rate of 2% per week on the value of the item rejected till
such disposal. The decision of the Tender Inviting Authority or any officer
authorized by him on the quality of the items supplied shall be final and
binding.
B.
In case of supply of inferior products or products not conforming to
specifications, the Tender Inviting Authority will be at liberty to terminate
without assigning any reasons thereof the contract either wholly or in part on
30 days notice. The supplier will not be entitled for any compensation
whatsoever in respect of such termination.
C.
For infringement of the stipulations of the contract or for other justifiable
reasons, the contract may be terminated by the Tender Inviting Authority,
and the supplier shall be liable for all losses sustained by the Tender Inviting
Authority, in consequence of the termination which may be recovered
personally from the supplier or from his properties, as per rules.
27.
D.
Non performance of any of the contract provisions will disqualify a firm to
participate in tenders issued by the Tender Inviting Authority for the next five
years.
E.
In the event of making ALTERNATIVE PURCAHSE, the supplier will be imposed
penalty apart from forfeiture of Security Deposit. The excess expenditure
over and above contracted prices incurred by the Tender Inviting Authority in
making such purchases from any other source or from the open market shall
be recovered from the Security Deposit or from any other money due to the
supplier and in the event of such amount being insufficient, the balance will
be recovered personally from the supplier or from his properties, as per
rules.
F.
In all the above conditions, the decision of the Tender Inviting Authority shall
be final and binding.
ARBITRATION
Any dispute whatsoever in any way arising out of or relating to the contract
shall be referred to arbitration of the Mission Director, National Rural Health
Mission, Assam or to the sole arbitration of some person nominated by him.
There shall be no objection if the arbitrator so appointed happens to be an
employee of National Rural Health Mission, Assam. The award of the
arbitrator shall be final, conclusive and binding on all parties.
28.
SAVING CLAUSE
No suit, prosecution or any legal proceedings shall lie against Tender Inviting
Authority or any person for anything that is done in good faith or intended to
be done in pursuance of tender.
29.
LAWS GOVERNING THE CONTRACT & JURISDICTION
The contract shall be governed by the laws in force in India. In the event of
any dispute arising out of the tender such dispute would be subject to the
jurisdiction of the Court within the State of Assam only.
**************
ANNEXURE I
UNDERTAKING (by the Bidder)
To
Mission Director,
National Rural Health Mission, Assam
Tender No.______________
For supply of ___________________
Sir,
1.
I,
Shri
_________________________________,
on
_______________________________________________
behalf
having
of
M/s
registered
office at __________________________, do hereby declare that I have gone
through the terms and conditions mentioned for the above and undertake to
comply with all tender terms and conditions. The rates quoted by me/us are
valid and binding on me/us for acceptance for a period of one year from the date
of award of contract to us.
2.
I/We
undersigned
hereby
bind
myself/ourselves
to
the
Office
of
……………………………….to supply …….…………………………………….. The rates quoted by
me/us for the items tendered for are specified against each. It is certified that
rates quoted are lowest quoted for any institution in India and not higher than
the MRP/ prevailing market rate.
3.
The articles shall be strictly as per specification and of the best quality as per
requirement
of
the
institution.
The
decision
of
the
Office
of
…………………………………………………. (Hereinafter called the said Purchaser) as
regards to the quality and specification of article shall be final and binding on
me/us.
a) Authorization from Manufacturer:- We shall furnish authorization from the
manufacturer legally enforceable undertaking to the Purchaser in appropriate
format obligations valid for a period ……years from the date of supplied
equipment.
4.
We agree to the conditions of the tender under which the EARNEST MONEY
DEPOSIT and PERFORMANCE SECURITY DEPOSIT shall be forfeited by us.
5.
We hereby undertake to pay the penalty as per the terms and conditions of the
contract for delayed supply of the ordered items.
6.
We agree to accept the amount of the bill to be paid by the purchaser after
completion of all formalities and should any amount of the bill found by the
purchaser/auditors to have been over-paid; the amount so found shall be
refunded by me/us.
7.
We hereby undertake to supply the items during the validity of the tender as per
direction given in supply order within the stipulated period.
8.
The tender inviting authority has the right to accept or reject any or all the
tenders without assigning any reason.
9.
We understand all the terms and conditions of the contract and bind
myself/ourselves to abide by them.
10.
We hereby
declare
that
there
is
no
vigilance/CBI
pending/contemplated against us at the moment.
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
or
court
case
ANNEXURE -II
MANUFACTURER’S AUTHORIZATION FORM (issued by the Manufacturer)
N0.
DATED
To,
Mission Director
National Rural Health Mission, Assam
Tender No.
Respected Sir,
We _________________who are established and reputable manufacturers of ________having factories at
_______________________________________________
registered office at_____________possessing
manufacturing License No. __________________________________dated________________Valid up to
_____________________hereby
authorize
_________________________
(name
and
address
of
representative and firm), to submit a bid and subsequently negotiate and sign the contract with you against
the above mentioned tender for the following items quoted.
1.
2.
We hereby certify that the Machine / spare parts do not contain any recycled or reconditioned parts or
components
We hereby extend our full guarantee and warranty as per clauses of contract for the goods offered for supply
against this Invitation for Bid by the above firm.
(Attach Separate sheet if necessary)
SIGNATURE
NAME & DESIGNATION
:
:
ANNEXURE-III A
ANNUAL TURNOVER STATEMENT OF THE BIDDER
The Annual Turnover of M/s ______________________________________ for the past
three financial years are given below and certified that the statement are true and correct.
Sl No.
Year
1.
2010-11
2.
2011-12
3.
2012-13
Date
:
Seal
:
Turnover in Lakhs
Total
-
Rs.____________ Lakhs
Avg.
-
Rs.____________ Lakhs
Signature of Auditor / Chartered
Accountant
(Name in Capital Letters)
ANNEXURE-III B
ANNUAL TURNOVER STATEMENT OF THE MANUFACTURER
The Annual Turnover of M/s ______________________________________ for the past
three financial years are given below and certified that the statement are true and correct.
Date
Seal
Sl No.
Year
1.
2010-11
2.
2011-12
3.
2012-13
:
Turnover in Lakhs
Total
-
Rs.____________ Lakhs
Avg.
-
Rs.____________ Lakhs
Signature of Auditor / Chartered
Accountant
(Name in Capital Letters)
ANNEXURE-IV
Performance Statement (of the Bidder)
Tender No:
Sl.
Name of the product
(only for Hospital Furniture,
Fixtures, Equipments,
Instruments, Hollow Wares)
1
Year
Qty supplied
Value
Name and full address of the
purchaser
2
3
4
5
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
(Please use additional sheets if required)
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
ANNEXURE-V
CERTIFICATE OF SALE TAX VERIFICATION TO BE PRODUCED BY AN APPLICANT
(To be filled by the applicant)
01.
Name or style in which the applicant is assessed or assessable to Sales Tax Addresses or
assessment ………………………………………………………………………….....
02.
a. Name and address of all companies, firms or associations or persons in which the applicant is
interested
in
his
individual
or
fiduciary
capacity……………………………………………………………………………………………………………
………………………………………..
b.
Places of business of the applicant (All places of business should be mentioned)
………………………………………………………………………………………
03
The Districts, taluks and divisions in which the applicant is assessed to Sales Tax (All the places of
business should be furnished).
……………………………………………………………………………………………………………………
…………………………………………………………………
04
a. Total contract amount in the preceding three years.
i. 2010-11
ii. 2011-12
iii. 2012-13
b. Particulars of Sales Tax for the preceding three years.
Year
Total T.O. be
assessed Rs.
Total Tax
Assessed Rs.
Total Tax paid
Rs.
Balance Due
Rs.
Reasons for
balance Rs.
2010-11
2011-12
2012-13
c.
If there has been no assessment in any year, whether returns were submitted any, if there were,
the division in which the returns were sent.
d. Whether any penal action or proceeding for the recovery of Sales Tax is pending
e.
The name and address of Branches if any:
I declare that the above mentioned information is correct and complete to
the best of my knowledge and belief.
SIGNATURE
NAME & DESIGNATION
DATE
NAME & ADDRESS OF THE FIRM
:
:
:
Enclosure of ANNEXURE-V
(To be issued by the Sales Tax Assessing Authority)
In my opinion, the applicant M/s…………………………………………….. has been / has not been /
doing everything possible to pay the Tax demands promptly and regularly and to facilitate the
completion of pending proceedings.
Date Seal
:
Deputy / Asst. Commercial Tax Officer
Note
:
Separate certificates should be obtained in respect of each of the place of
business of the applicant from the Deputy Commercial Tax officer or
Assistant Commercial Tax Officer having jurisdiction over that place.
ANNEXURE-VI
Tender No:
UNDERTAKING FOR EMBOSSMENT OF LOGO
We M/s …………………………………………………………. do hereby declare that, if favored with an order,
we will supply the Hospital Furniture/Fixtures/Equipments/Instruments/Hollow Wares embossed
with NRHM Logo and the words “NRHM ASSAM SUPPLY” or as per any other instructions given in
this regard.
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
LOGOGRAM
ANNEXURE – VII
Declaration on Manufacturing Facilities by the Manufacturer
Tender No.______________
For supply of ____________________________
1.
Name of the manufacturer
:
2.
Full Postal Address
:
3.
Telephone No. /Fax No.
:
4.
Email address
:
5.
Date of inception of business
:
6.
Registration no. & Date
:
7.
Issued by
:
8.
Valid till
:
9.
Details of manufacturing activity
& item wise capacity
:
12.
Name of Govt. Departments/ Pvt. Institutions : As per enclosure
to which the bidder already supplied the items
with quantity value and supply period
18.
Has the bidder ever been black listed
by any govt. agency? If yes, give details.
:
14.
Are any cases pending in the court related to
any supplies? If yes, give details
:
15.
Does the firm have the adequate facilities for :
Inspection and quality control?
Please give details
___________________________________________Prop./partner/Director
I,
of
M/s
________________________________________________________
Hereby declare that the information given in this form is true and correct to the best of my
knowledge & belief.
I/we agree to the tender Inviting Authority forfeiting the Earnest Money Deposit and/or
Performance Security Deposit and blacklisting us for a period of 5 years, if any information furnished
by us is proved to be false at the time of inspection and non – compliance with terms and conditions
of the contract
I offer to supply the items mentioned in the schedule (enclosed in price bid) at the rates quoted
therein. I agree to hold this offer for one year after finalization of rate contract.
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE MANUFACTURER
:
The details of manufacturing unit shall be for the premises where items quoted are actually
manufactured.
Annexure –VIII A
List of items quoted
(To be submitted separately for Group A, Group B, Group C, Group D, Group E & Group F)
Tender No._________________
List of items Group A (X-Ray)/ Group B (USG)/ Group C (Ventilators)/ Group D (Equipments)
/Group E (Furniture &Fixture) & Group F (Instruments)
Sr.
No.
Description of Items
Group (
)
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
Manufacturer’s
Warranty
Price
Technical
Name
Period in
Quoted/
Specifications
Years
Not
Attached/Not
Quoted
Attached
Annexure –VIII B
Technical Compliance Statement
(To be submitted separately for Group A, Group B, Group C, Group D, Group E & Group F)
Tender No._________________
Sr.
Name of the Item
No.
Group(
)
Technical Specifications as
Technical Specifications
per Tender (Annexure-XIII)
quoted by the bidder
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
Deviations, if any
ANNEXURE IX
UNDERTAKING ON FRAUD & CORRUPTION (for bidder)
We ……………………….. do hereby undertake that, in competing for (and, if the award is made to us, in
executing) the subject contract for supply of Hospital Furniture/Fixtures/Equipments/Instruments
under tender reference no ……………………………… …………………………………… we shall strictly observe the
terms and conditions against fraud and corruption in force in the country.
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
ANNEXURE– X
NATIONAL RURAL HEALTH MISSION, ASSAM
AGREED TERMS & CONDITIONS
Tender No. & Date ____________
A. Details of Bidder
Bidder Name:
Offer Ref:
Contact Person:
Telephone No:
Signature:
Fax No:
E-mail:
B. Definitions
1. “Purchaser” means the Mission Director, National Rural Health Mission, Assam or his
authorized representative.
2. “Bidder” means a person or firm or company who has made an offer for supply of
goods and /or service as per tender.
3. “Vendor” or “Supplier” means a person or firm or company, to whom the order is
addressed for supply of goods and /or services.
4.
“Site” means the premises of the purchaser or any other place as decided by the
Purchaser.
NOTE: The questionnaire below must be duly filled in and should be enclosed with un-priced
Technical Bid, (Cover A). Clauses confirmed here under should not be repeated. All commercial
terms and conditions should be indicated in this format. If necessary, details including deviations
to the terms and conditions of the bid document, if any, should be enclosed as annexure to this
questionnaire.
Sl. No.
1.
2.
3.
4.
5.
6.
1.
2.
Description
C. Technical
Confirm that you meet the eligibility criteria as per bid
document and have furnished relevant documents.
Confirm acceptance of Technical Specification and
scope of supply as per Tender Document.
In case of deviations, confirm that the same have been
highlighted separately.
Confirm that literature and technical data, wherever
applicable, have been enclosed.
Confirm that all certificates/ documents furnished.
Confirm that Earnest Money Deposit (EMD) as per bid
document has been furnished in Cover A
D. Commercial
It is noted that any deviations to the commercial terms
and conditions shall lead to loading of prices or
rejection of offer.
Confirm that the quoted landed price is inclusive of cost
of containers, packing & forwarding charges, freight,
insurance and all duties and taxes viz. Excise Duty, Sales
Vendor’s Confirmation
(Confirmed/Noted/Deviation
furnished separately)
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Tax/VAT.
Confirm furnishing of price break-up of each item
showing basic price of item and Tax/VAT on %age of
basic price to arrive at landed price in D2 above.
It is noted that the statutory variations in taxes and
duties within the contractual delivery period shall be
borne by the purchaser.
If there is any variation or fresh imposition of Excise
Duty at the time of supply due to various reasons,
including turn-over, confirm that the same shall be
borne by supplier.
If clause 5 above is not acceptable, advice maximum
possible rate of additional ED chargeable; this shall be
loaded to your price.
Confirm that in case any new or additional duties and
taxes are imposed after the contractual delivery date
due to delays attributable to the supplier the same shall
be borne by the supplier. This will be in addition to
Price Reduction for Delay in Delivery.
Confirm acceptance of Price Reduction Schedule for
delay in delivery @ 0.5% of delayed value of goods per
week of delay or part thereof subject to maximum of
10% of the total order value.
Confirm acceptance of Delivery Period as indicated
under clause 17 (c) of the bid document.
Confirm acceptance of relevant payment terms
specified in the bid document.
It is noted that delivery period, price reduction,
termination etc are subject to Force Majeure Condition
as stipulated in the bid document.
Confirm that the quoted prices are in Indian Rupees
and shall remain firm & fixed till complete execution of
the order.
a) In case you are a manufacturer confirm that the
prices quoted are not higher in any respect than MRP
b) In case you are a dealer/ distributor / authorized
agent, confirm that the prices quoted are as per
manufacturer’s price list with appropriate discount
(Copy of Price list to be enclosed).
Packing / forwarding, transportation, loading/
unloading and insurance are supplier’s responsibility.
However, to protect the items from physical damages
and/or deterioration due to weather during transit,
supplier to ensure proper packing & handling
arrangement. Please confirm compliance.
Confirm that security deposit of 5 % of the total order
value in the form of a Bank Guarantee from a
nationalized Bank shall be furnished, which will be valid
for a period of 6 months from the date of order.
a) Confirm that all inspection & testing charges
including 3rd party inspection (if required) included in
the price.
b) Quality Control Reports and Test Certificates,
whenever applicable, shall be handed over to the
purchaser along with the equipment.
17.
18.
19.
20.
21.
22.
23.
24.
25.
a) Confirm that erection, commissioning, trial run and
handing over to the purchaser, after successful
commissioning is your responsibility at no extra cost.
b) Specify facilities (if any), like water supply/ electric
power to be provided by the purchaser for
commissioning of the equipment.
Packing / forwarding, transportation, loading/
unloading and insurance are your responsibility.
However, to protect the equipment from physical
damages and/or deterioration due to weather during
transit, you are to ensure proper packing & lifting
arrangement. Pl confirm compliance.
The material / equipment shall be guaranteed against
any and all defects in design, workmanship, material &
performance for a period shown in the Technical
specification, from the date of commissioning and
handing over to the purchaser. Should any defect
detected or develop during the guarantee period, it
shall be remedied promptly free of cost by the supplier
and all expenses including transportation of goods
necessitated for such repair and replacement shall be
done by the supplier. Pl confirm acceptance.
Confirm acceptance of Repeat order within 12 months
from the date of initial order at same price and terms &
conditions.
In case of material having shelf life, confirm that you
have declared the same with the expiry date. Also
confirm that such materials shall be dispatched within
30 days from the date manufacture.
It is noted that the purchaser would disown any
responsibility / liability towards irregularity,
contravention or infringement of any statutory
regulations including those of patent, on manufacture
or supply of goods covered by the order.
Terms & Conditions indicated in this format shall not be
repeated in the bid. Terms & Conditions indicated
elsewhere and contradicting those in this format shall
be ignored. Confirm compliance.
Confirm that you shall observe the highest standard of
ethics during bidding and in case favoured with an
order, the execution of the order will be completed,
without resorting to any fraud, corruption and/or
coercion.
Confirm that the offer shall be valid for a period of 90
days from the date of bid opening.
SIGNATURE & DATE
:
NAME & DESIGNATION
:
NAME & ADDRESS OF THE FIRM
:
:
ANNEXURE-XI
CHECK LIST
Sl.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13
14
15.
16.
17.
18.
19.
20.
21
21.
22.
Sl
1.
Cover A
Court Fee Stamp/IPO & Tender Document Fee furnished
EMD in the form of DD furnished
Documentary evidence for the Constitution of the company
Duly attested / notarized copy of License issued by the
competent Licensing Authority for the products quoted
Attested Photocopy of Import license if any
The instruments such as Power of Attorney, Resolution of
Board etc.
Undertaking as per Annexure I
Manufacturer’s Authorization as per Annexure II
Attested copy of CE/US FDA Certificate.
Attested copy of OHSAS 18001:2007 certificate for hospital
equipments & instruments
Attested copy of ISO 9001:2000/ISO 14001:2004 certificates
for hospital equipments & instruments
Attested copy of OHSAS 18001:2007 certificate for hospital
furniture and fixtures
Attested copy of ISO 9001:2000/ISO 14001:2004 certificate for
hospital furniture and fixtures
Attested copy of ISO 9001:2000 certificate for surgical hollow
wares
Annual Turnover Statement for 3 years (Annexure – III A &
Annexure –III B)
Performance Statement as per Annexure IV
Sales Tax Clearance Certificate as Annexure V
Undertaking for Embossment of logo as per Annexure VI
Details of Manufacturing Unit as per Annexure VII
List of items quoted with name of Manufacturer as per
Annexure VIII A
Technical Compliance Statement as per Annexure VIII B
Undertaking on Fraud & Corruption as per Annexure IX
Agreed Terms & Conditions as per Annexure- X
Yes
No
Cover B
Price Bid as per Annexure XII (A) ,XII(B),XII(C),XII(D),XII(E) &
X(F)
Yes
No
ANNEXURE XII A
PRICE BID FOR GROUP “A” ITEMS
TENDER NO…………………………………….
Sl
Brief Description of items
Group( A)
Qty.
Nos.
Basic Rate per
unit
Rs
1
1
2
3
4
Tax/VAT per
unit
Rs
Total
(For supply)
Rs
3 x(4+5)
CAMC charge
(for 3 years)inclusive of al
taxes
Rs
Total
(For CAMC)
Rs
3 x7
5
6
7
8
Total
(Supply+ CAMC)
Rs
(6+8)
9
2
3
4
5
Grand Total =
Rs………………………
Rs (in words)………..
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
ANNEXURE XII B
PRICE BID FOR GROUP “B” ITEMS
TENDER NO…………………………………….
Sl
Brief Description of items
Group ( B)
Qty.
Nos.
Basic Rate per
unit
Rs
1
1
2
3
4
Tax/VAT per
unit
Rs
Total
(For supply)
Rs
3 x(4+5)
CAMC charge
(for 3 years)inclusive of all
taxes
Rs
Total
(For CAMC)
Rs
3 x7
5
6
7
8
Total
(Supply+ CAMC)
Rs
(6+8)
9
2
3
4
5
Grand Total =
Rs………………………
Rs (in words)………..
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
ANNEXURE XII C
PRICE BID FOR GROUP “C” ITEMS
TENDER NO…………………………………….
Sl
Brief Description of items
Group (C )
Qty.
Nos.
Basic Rate per
unit
Rs
1
1
2
3
4
Tax/VAT per
unit
Rs
Total
(For supply)
Rs
3 x(4+5)
CAMC charge
(for 3 years)inclussive of
all taxes
Rs
Total
(For CAMC)
Rs
3 x7
5
6
7
8
Total
(Supply+ CAMC)
Rs
(6+8)
9
2
3
4
5
Grand Total =
Rs………………………
Rs (in words)………..
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
ANNEXURE XII D
PRICE BID FOR GROUP “D” ITEMS
TENDER NO…………………………………….
Sl
Brief Description of items
Group (D)
Qty.
Nos.
Basic Rate per
unit
Rs
1
1
2
3
4
Tax/VAT per
unit
Rs
Total
(For supply)
Rs
3 x(4+5)
CAMC charge
(for 3 years)inclusive of all
taxes
Rs
Total
(For CAMC)
Rs
3 x7
5
6
7
8
Total
(Supply+ CAMC)
Rs
(6+8)
9
2
3
4
5
Grand Total =
Rs………………………
Rs (in words)………..
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
ANNEXURE XII E
PRICE BID FOR GROUP “E” ITEMS
Tender No._______________
SL
DESCRIPTION OF ITEM
Group(E)
Quantity
in Nos.
1
2
3
Basic Rate
per No.
(in Rupees)
4
TAX/VAT
(in Rupees)
Total Amount (in rupees)
3 x (4+5)
5
6
In Figures
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
In Words
ANNEXURE XII F
PRICE BID FOR GROUP “F” ITEMS
Tender No._______________
SL
DESCRIPTION OF ITEM
Group (F)
Quantity
in Nos.
1
2
3
Basic Rate
per No.
(in Rupees)
4
TAX/VAT
(in Rupees)
Total Amount (in rupees)
3 x (4+5)
5
6
In Figures
SIGNATURE
:
NAME & DESIGNATION
:
DATE
:
NAME & ADDRESS OF THE FIRM
:
In Words
ANNEXURE XIII A
SPECIFICATIONS & DETAILS OF ITEMS
GROUP (A)
Si No
1
Specifications
Qty(Nos)
10
X-Ray Machine 100 mA with dark room accessories .
Counter Balanced vertical movement mechanism of Tube
carriage for easier positioning.
Digital Display for Input Voltage compensation, X-Ray ON
and Overload Protection.
LCD Display for mAs, Technic, kVp and Body Part .(In case of
Digital Machines)
Automatic overload Protection with visual and audible
indication for longer life of theTube.
Independent kVp, mAs, mA techniques selection for-better
radiographic results.
Microprocessor based system for accurate time selection
for exposure.
Expose at 220 (An actual Input Voltage) display indicates
whether line voltage
Compensation is to be increased or decreased.
Integrated cassette box for easier cassette handling.
Line Voltage Compensation from 190v to 270v.
Standby Circuitry in case of any Electronic Component
failure thereby ensuring maximum up time.
Automatic cut off for High lnput Voltage.
Soft Touch keys for Body Part Selection. (In Case of Digital
Machines)
Beautiful Cover for Generator as a safety measures against
dust.
anatomical Programme Mode through that when user
selects the anatomical part kVp,mA and mAs will
automatically set
SPECIFICATIONS
Radiographic Rating : 25mA, 50mA, 75mA & 100mA (For 100mA)
At 45-100kVp in steps of 5kVp
At 40-100kVp in steps of 2kVp (Digital
Model)
Tube Current : 25mA, 50A, 75mA & 100mA (For 100mA)
25mA, 40mA and 60mA (For mA)
Tube Voltage : 45-100 kVp (Each Step of 5 kVp)
40-100 kVp (Each Step of 2kVp) (Digital Model)
Timer : Automatic selection by Microprocessor
(Using Combination of mAs& mA)
Tube Type : Stationary Anode Tube
Power Requirement : 220 V a.c/50Hz Single Phase
(4.9 KW for 60 mA/8.0 KW for 100 mA)
For the unit to operate safety and correctly, observe the
environmental conditions specified below. In case of storing the
unit for a long time, give special. consideration to ventilation at the
place of storage.
TEMPERATURE : Below 50 degrees
HUMIDITY : 30 to 85% (Non Condensing)
Dark Room Accessories:X.ray developing tank
S.S, 4.5, Ltrs with lid
S.S, , 9, Ltrs with lid
S.S, 13.5 Ltrs with lid
Safe light X.ray dark room:- Size: 5” x 7”
Cassettes X.ray
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15"
Lead Apron:-Full front side
Intensifying screen X-ray
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15"
Half Blockers :- Size 8" x 10", 10" x 12", 12" x 15"
X-Ray Adoption Google
X-Ray Lead Markers
Processing Tray
X-Ray Film Cutter
X-Ray Film Hangers
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15
Warranty for 2yrs
2
X-Ray Machine 300 mA with dark room accessories.
Output:- 24 KW
Tube Voltage – Radiography :- 40 kVp – 125 kVp (Each step
of 2 kVp)
Tube Voltage –Fluroscopy :- 40 kVp – 125 kVp (Each step
40
of 2 kVp)
Tube Current : Small Focus : 50mA , 100 mA
Large Focus :- 200 mA , 300 mA
mAs Rating: 2 to 500 (Each step of 2 mAs)
Technic : 50 mA, 100 mA, 200 mA, 300 mA
Timer : Automatically selected by microprocessor.
Tube Type:- Dual Focus Rotating Anod Tube.
Fluoroscopy Rating (Optional) :- 0.1-3 mA at 40 -100 kVp
Fluoroscopy Timer (Optional) :- 5 minutes cumulative with
audible indication after 30 seconds.
Power Supply:- 440 V, 50/60 Hz with three to single phase
transformer.
Power Requirement: - 30 KVA.
BIS 7620 Part I Approved for Mechanical & Electrical Safety.
AERB Approved for Radiation Safety.
ISO 13485:2003 & ISO 9001:2000 Manufacturing Facility.
CE Certified.
Dark Room Accessories:X-ray developing tank
S.S, 4.5, Ltrs with lid
S.S, , 9, Ltrs with lid
S.S, 13.5 Ltrs with lid
Safe light X-ray dark room:- Size: 5” x 7”
Cassettes X-ray
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15"
Lead Apron:-Full front side
Intensifying screen X-ray
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15"
Half Blockers :- Size 8" x 10", 10" x 12", 12" x 15"
X-Ray Adoption Google
X-Ray Lead Markers
Processing Tray
X-Ray Film Cutter
X-Ray Film Hangers
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15
Warranty for 2yrs
3
X-Ray Machine 500 mA with dark room accessories .
TUBE UNIT: Rotating Anode Tube Unit with Focal spot 1.2
and 2.0 Sq.mm. THX-1/125/DRA-1/20/40.
HV CABLE: Pair of 6 meter High Voltages Cables. Sleeving –
Straight.
STAND: Floor to Ceiling Stand & with Counter balanced
movement, 360 Degree rotatable; mounted on floor ceiling
rails for convenient movements.
TABLE: Horizontal Table with Motorized Bucky & Grid with
ratio 6:1
HV TRANSFORMER: Compact Heavy Duty transformer
comprising HV Silicon Rectifiers, HT Transformer, Filament
Transformer, Federal Bushing all immersed in oil.
GENERATOR: 500mA, 125 KVP Full Wave Silicon Rectified
X-GENERATOR for Radiography, Fluoroscopy & Spot
Filming. As per IS: 7620 Part-I.
RATING: RADIOGRAPHY:
Small Focus: 100mA - 40 to 125KVP
200mA - 40 to 125KVP
Large Focus: 300mA - 40 to 125KVP
400mA - 40 to 125KVP
500mA - 40 to 125KVP
STATIC BALANCER: Phase Reducing Transformer. 50 KVA- 3
Phase Transformer.
ACCESSORIES: Hand switch with Flexible long cord enables
the operator to keep from the Radiation area during
exposure. Aluminum Filters 1.5 mm
COLLIMETER: Light Beam Diaphragm with auto time cut off.
POWER SUPPLY REQUIRMENT: 400/440V, 3 Phase 50 Hz,
50 KVA.
Dark Room Accessories:X.ray developing tank
S.S, 4.5, Ltrs with lid
S.S, , 9, Ltrs with lid
S.S, 13.5 Ltrs with lid
Safe light X.ray dark room:- Size: 5” x 7”
Cassettes X.ray
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15"
Lead Apron:-Full front side
Intensifying screen X-ray
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15"
Half Blockers :- Size 8" x 10", 10" x 12", 12" x 15"
10
X-Ray Adoption Google
X-Ray Lead Markers
Processing Tray
X-Ray Film Cutter
X-Ray Film Hangers
Size: 8"x10",
Size: 10" x 12"
Size : 12" x 15
Warranty for 2yrs
ANNEXURE XIII B
SPECIFICATIONS & DETAILS OF ITEMS
GROUP (B)
Si No
1
Specification
USG with Servo Voltage Stabilizer.
SPECIFICATION:
Imaging mode
Harmonic
Qty(Nos)
73
B, B/B, 4B, B/M, M, Tissue
Scanning mode
Electronic
convex/Linear/Micro Convex
Gray scale
256
Display
15” high resolution medical
grade LCD display.
Probe frequency
Probe connector
Broad band 5 steps
frequency
selection,
working frequency 2MHz12MHz
3 (standard)
Dynamic imaging
Dynamic frequency scan,
multi-step dynamic focusing
Technology
Focusing method
Dynamic focusing, variable
aperture
Gain control
Overall gain control, 8 step
TGC
continuously
adjustable
Image reverse
Image magnification
Left/right, up/down
max. 4.0, local zoom
function, in 8 steps: 0.5,
0.8, 1.0, 1.2, 1.5, 2.0, 3.0
and 4.0
Cine loop
More
(depends on probe & mode)
Image storage
Connectivity
Line density
than
250
frames
Minimum 1000 images can
be stored
Full
patient
database
solutions: 160G hard disk,
CD/DVD righter, 4 USB ports,
DICOM 3.0 & AVI/JPG
format.
low, high
Edge enhancement
Gray scale curve
Persistence
Chroma / Color Pallate
Adjustable parameters
Diagnostic mode
Systems upgrade
through software
Clinical application
Standard Offered
Standard Accessories:
8 steps
8 types
8 steps
8 types
dynamic range, frequency, GSC,
persistence, enhancement,
grayscale curve, left/right
invert, up/down invert,
image rotation angle,
sweep angle/width, zoom
factor, focus number and
position, biopsy guide line;
applications such as
cardiac, liver, kidney,
muscular-skeletal,
gynecological, obstetric,
thyroid, carotid, breast and
pancreas preset can be
created by the user
Flexible system upgrade
General, Radiology, OB/Gyn,
Urology,
Pediatric,
Musculoskeletal etc.
Main unit including 15” TFT
display
+
2
probe
connector + 1 Convex
probe(2-6 MHz) + 1 T.V.
prove (4-9 MHz)
Trolley, Servo-stabilizer, B/W
thermal printer.
Warranty for 2yrs
ANNEXURE XIII C
SPECIFICATIONS & DETAILS OF ITEMS
GROUP (C)
Si No
Specification
Qty(Nos)
30
1
Ventillator (Paediatric):Description of Function
ICU ventilators should provide artificial respiratory support
to the critical patients in all the types of Intensive Care Units
with altitude compensation for volume and BTPS correction
for monitoring.
Operational Requirements
It should be microprocessor Controlled ventilator with
integrated facility for Ventilation monitoring suitable for
Neonatal (including premature) to adult ventilation.
The unit should be external compressor based for precise gas
delivery (not a turbine / piston/ blower based internal
compressor) .It should have proximal flow sensor for
neonatal patient category only. Demonstration of the
equipment is a must.
Technical Specifications
Hinged arm holder for holding the circuit
Should have Colored Touch screen, 12 Inch or more
It should have inbuilt facility to measure and display for all
patient category ( Adult to neonatal )
3 waves- Pressure and Time, Volume and Time and Flow and
Time., Co2 and Time
3 loops- P-V, F-V, P-F with facility of saving of 4 Loops for
reference. Also facility to display volumetriccapnography
loops
Graphic display to have automatic scaling facility for waves
Status indicator for Ventilator mode, Battery life, patient
data, alarm settings, clock etc.
Simultaneous display of SET and exhaled parameter , 3
waveform and 2 loops and Alarm
Should have Trending facility for 72 hours
Should have Automatic compliance & Leakage compensation
for circuit and ET tube with ET Tube size and % of
compensation
Integrated( in main unit )Mainstream End tidal CO2 with
Capnography with monitoring of PeCO2, Vmin VCO2, Curve
Co2/ time, Alveolar ventilation , expire Co2 ( VTCo2) ,Vhigh
and low alarms etc. external Etco2 monitor will not be
accepted. Mean stream EtCo2 Sensor - 1no reusable Adult
/ped, neontal adaptor - each 1 .
Should have following settings for all age groups.
a) Tidal Volume 5 ml to 1800 ml
b) Pressure (insp) 2- 90 cmH2O
c) Pressure Ramp/ Flow patterns
d) Respiratory Rate 1 to 150 bpm, Insp. Time 0.1 to 9 sec, I :
E Ratio 5:1 to 1:5
e) Insp. Flow ( resultant) 0.3 to 180 LPM, continuous Flow 238pm ( in TCPL ode)
f) CPAP/PEEP 0-45 cmH2O
g) Pressure support 2-80 cmh2O
h) FIO2 21 to 100%
i) Pause Time 0 to 2 sec
j) Flow Trigger 0.2 to 12 lpm . Pressure Trigger 0.5 to 15
cmH2O
k) Expiratory trigger or exhalation sensitivity - 5-75-% of flow
Should have ,monitoring of the following parameters
a) Airway Pressure (Peak & Mean)
b) Tidal volume (Inspired & Expired)
c) Minute volume ( Expired)
d) Spontaneous Minute Volume
e) Total Frequency
f) FIO2 dynamic
g) Intrinsic PEEP and PEEPi Volume (or trapped Volume)
h) Plateau Pressure
i) Resistance ( Rinsp&Rexp)& Compliance ( Cdyn&Cstat)
j) Use selector Alarms for all measured & monitored
parameters
Should have following modes of ventilation
a) Volume controlled
b) Pressure Controlled
c) Pressure Support
d) SIMV (Pressure Control and volume control) with pressure
support
e) CPAP/PEEP, PSV + assured tidal volume / guarantee /
volume support
g) Advanced mode like pressure controlled volume
guaranteed / PRVC / AUTOFLOW
h) Non Invasive ventilation ( NIV Mode )
i) Additional mode advance ASV / NAVA / MMV+ PSV /
j) APRV
k)Special Neonatal modes - Yime cycled pressure limited
with continuous flow (TCPL) , SIMV +TCPL + PSV, N-CPAP(
with continuous flow) , PRVC,APRV,and above mentioned
mode
Should have Apnea /backup ventilation. Back up mode
should user adjustable and bi directional (auto switch over
from spont. to control and vica-versa
Expiratory block should be autoclavable and no routine
calibration required
Should have, monitoring of the following parameters
a. Intrinsic Peep & Intrinsic PEEP Volume (Trapped Volume)
b. Occlusion Pressure( P0.1) , Max Inspiratory pressure (Pi
max)
c. Non-forced Slow Vital Capacity , physiologic Dead space,
RSBI, Imposed work of Breathing ( WOBi), Expiratory Time
constant ( Tcexp)
d. Facility to calculate lower and upper inflection point ( P/V
Flex points)
e. Facility for ET Tube compensation with tube diameter (
4mm onward) and % of compensation and Patient circuit
compensation
Should have integratedNebulizer with capability to deliver
fine particle size of to be used in On line
Should have Ideal Body Weight facility
Should integrated Battery backup for minimum 2 hour for
main unit
RS 323C interface for communications with networked
devices.
System Configuration Accessories, spares and consumables
ICU Ventilator with trolley - 01
Adult , Pediatric , Neonatal autoclavable silicone patient
breathing circuits -02 each
Reusable and autoclavable Flowsensor and exhalation valve/
expiratory cassette - 4 no’s. each. The expiratory flow sensor
and valve should have 2 years replacement warranty
Proximal Flow sensor for neonatal use - 10 no’s
Hinged Support Arm - 1no
Air and Oxygen Hose - each 1 no
Medical Air Compressor with CE mark
Reusable Masks (Small, Medium, Large) with each machine.01 sets ea
Humidifier -Servo controlled fisher and paykel MR 850 with
digital monitoring of inspired gas temperature -01 .
All accessories required like temp. Probe, heating wire, draw,
chamber etc - each 2 nos.
Inlet requirement
Power input to be 220-240VAC, 50Hz
Gas input( air and oxygen) - 50-100 psi
Standards, Safety and Training
Should have US FDA and CE for main ventilator unit for the
entire feature mentioned the specification.
The company should attach valid 510K and US FDA
certificate along in the technical bid.
Demonstration of quoted equipment model is a must.
Should have local service facility .The service provider should
have the necessary equipments recommended by the
manufacturer to carry out preventive maintenance test as
per guidelines provided in the service/maintenance manual.
Warranty for 2yrs and provision of CMC for next 5 years
2
Ventilator (Neonatal):High End neonatal ventilator with HFOV
General Requirement
Should be able to ventilate patients with body weight from
400 grams to 25 kg
Should have battery back-up for the ventilator with
integrated re-chargeable battery for a minimum of 60 min
operation
Should have high resolution screen with colour display of at
least 10 inches screen size
Should have an integrated electronic blender for blending Air
& Oxygen
Should have based on external compressor
Should have US-FDA and / or European CE certification for
neonatal use
The flow sensor should be reusable and autoclavable and
should be located proximal between the Y piece and
Endotracial tube. Flow sensor should have replacement
warranty.
Should have device checking mechanism where it can
determine and display the compliance and resistance of the
system, determine leakage in the patient hose system and
checking of valves, gas supply system, flow sensors etc
Should have an automatic leak compensation facility that
provide sensitive triggering even with changing ET-Tube
leaks
Ventilation Modes required:
Invasive ventilation:
a) Pressure limited: SIMV, Assist control/SIPPV, Pressure
support (PSV), Apnea back up ventilation
b) Should have volume targeting or volume assured or
volume gurantee function in all pressure limited modes to
ensure a preset tidal volume delivery by varying the peak
pressure or inspiratory time.
Non Invasive ventilation: N- CPAP and NIMV
Should have apneoa backup facility with backup settings
configured for neonates.
should have HFOV modes with active exhalation like CPAP+
HFOV, IMV+ HFOV with selection for switch on / Off during
Insp. Time
should have setting for HFOV MAP 0-30 cmH20, Frequency
5-15 Hz, Amplitude 0-100 % ,o Inspiration time – 33 % to 50
% adjustable,
Waveforms and loops:
Scalar graphics - for pressure, volume and flow; scale should
be user selectable and adjustable for neonatal settings
Loop Graphics - for pressure volume, flow volume, pressure
flow combinations; scale should be user selectable and
adjustable for neonatal settings
Should have freezing and measuring facility for loops and
curves. Freeze and Analysis cursor in all loops
Facility of moveable cursors to read numeric values at any
30
point on the loop where the cursors is kept
Should have adjustable inspiratory flow patterns from square
wave, sinusoidal and decelerating wave
Ventilator Parameters and settings:
Should have knobs for setting following parameters - Peak
pressure ( 5-60 cmH2), Positive end expiratory pressure
(PEEP- 0-30 cmH2O), Respiratory rate ( 0-200 bpm),
Inspiratory rate (o.1 to 2 sec) & Expiratory time( 0.1 to 10
sec) , Oxygen concentration (in 1% increments or
decrements), tidal volume ( 2 ml - 150 ml)
Should be able to monitor the following parameters : Peak
pressure, PEEP, Mean airway pressure (MAP), Respiratory
rate, FiO2, Minute volume, Tidal Volume (Inspired & Expired,
Leak percentage), Resistance, Compliance
Should have following settings and ranges:
a) Inspiration time: 0.1 - 3 sec
b) Expiration time: 0.1 - 10 sec
c) Respiratory rate up to 300 breaths per minute in
conventional modes
d) Flow: Preset patterns - Square, Sinusoidal, decelerating
e) PEEP: 0 - 30 mbar/cmH2O
f) Inspiratory pressure: 5 - 50 mbar/cmH20
g) Tidal volume: 2 - 150 ml
h) Proximal flow trigger facility with a trigger sensitivity of at
least 0.21/min
i) Oxygen concentration (FiO2): 21% to 100%
Display:
Inspiratory time %
Ventilator rate
Mean airway pressure
Inspired oxygen concentration
Tidal volume & Minute ventilation
Trends of set and measures parameters with a trend
memory of at least 24 hrs.
Leak percentage
Display of silenced alarms
Alarms Limit: Should have visual as well as audible alarms
with user adjustable alarms levels with text message for:
Power failure
Circuit disconnection
low tidal volume
Minute volume
Tidal volume
Peak Pressure
PEEP
Mean airway pressure
Patient disconnection
Gas failure
Low & High FiO2
Should have the facility to suspend the oxygen alarms
indefinitely when oxygen cell is depleted or defective
Power Supply: 220 - 240V and 50-60 Hz
Miscellaneous:
Complete unit should be mounted on a sturdy pedestal
trolley with good quality castors for easy movement of the
complete ventilator. At least 2 of the four wheels should be
lockable.
Each unit should have a circuit hanger to support the patient
circuit
Each unit should be supplied with a heated servo controlled
humidifier (Either integrated or Standalone) of the latest
model with temperature display for set as well as measured
temperature. The humidifier should have the following
requirements:
a) Heater with flow resistance up to 1 cmH20/ L/sec
b) Temperature range: 28 - 39 deg. C
c) Warm up time less than 15 minutes
d) Temperature control accuracy: +/- 2 deg. C
e) Automatic audible and visual alarms for high and low
temperatures
f) Visual indicator and alarm for low water level and digital
display for set and measured temperatures
Nebulizer: Should be inbuilt and preferably volume
compensated with a time - programmable flow mechanism
to de-activate nebulizer
Manual oxygen key while suction; user adjustable oxygen
concentration delivery while this manual mode is operated
Should have an adjustable mechanism relief valve for excess
pressure
Should be able to connected to central air line via and
external compressor so that the compressor automatically
switches ON when air pressure in the central line drops
below the recommended level
Should be able to connected to central O2 line
Each unit should come with 1 set of standard oxygen & Air
hoses with hose connectors
The firm should agree for periodic regular replacement of
oxygen cells, compressor filters and ventilator filters during
warranty and CMC
Accessories to be provided per ventilator
Autoclavable reusable high quality neonatal specific low
compliance heated ventilator circuits - 04 nos. Additional 4
nos. of reusable patient circuit should be provided in case of
separate patient circuits for HFOV application.
In case of standalone humidifier: 4 sets each of temperature
probes, reusable humidifier chambers, heater wire adaptors
for reusable circuits, and heater wire adaptors for disposable
circuits with each humidifier.
Reusable Proximal type flow sensors for neonatal use - 2 no
(if differential pressure transducer type) or 60 nos (if heated
wire anemometer type). In case of Heated wire anemometer
sensor supplied 60 nos per year during warranty and CMC
also.
Flow sensor cables (if heated wire anemometer type) - 5nos
Reusable Nebulization kits/ Cartridges with all accessories 1nos
Neonatal test lung - 1 no
Air compressor with automatic switch over in case of failure
of central air pipeline And with FDA or CE certificates- 1no.
Manuals: Operator & Service manuals
Should be FDA or European CE certified and approved
The equipment should come with aWarranty for 2yrs from
the date of satisfactory installation and 5 years
comprehensive maintenance contract after the end of the
warranty. Warranty and CMC should include all parts plastic, metallic, glass, batteries, electronic, electrical and
rubber. Warranty and CMC should cover the ventilator, flow
and o2 sensor, compressor, humidifier and the stand.
Warranty and CMC would include the periodic calibration of
all
parameters
strictly
as
per
manufacturer's
recommendations and any spares, gases or standards
required for that.
The quoted model should have installed in reputed
government organization and satisfactorily working since last
2 years.
On-sight physical demonstration of the ventilator with all
standard accessories will be mandatory if demanded by the
technical committee
Rates of consumables and accessories should be quoted
separately for the full duration of warranty and CMC
3
Transport Ventillator.:The portable ventilator is used to transport a patient with
artificial respiration support for all patient category (Adult,
pediatric and newborn)
Operational Requirements
The portable ventilator should be light weight( < 5 kg)
Should be based on IPPV time cycled and portable, light
weight.
Should electronically controlled and pneumatically driven.
Should be able to work both with cylinders and pipeline,
connectors and high-pressure tubing of appropriate length
to be supplied.
Technical Specifications
Should have venture /jet mixing- technology air - oxygen
mixture
Should have following modes of ventilation:
IPPV or control/Assist-control, Pressure Support +PEEP,
Apnea back up
should have facility to be used non -invasively
Should have following settings
a. TV 15 – 2000ml or minute volume setting 1-15 lpm
b. PEEP/CPAP 0-20cmH2O
c. Respiratory Rate 5 to 65bpm
d. I: E ratio 1:1.5 (inspiratory time 40% of breathing cycle)
e. FiO2 50% & 100%
f. pressure support level 0-50 cmH2O
Trigger Sensitivity - Pressure 1 to 5 cmH2O
Should have airway pressure monitoring
Should have Audio-visual alarms for
a. Low supply pressure
b. High/low airway pressure
c. Gas Supply
d. Power failure
e. Apnea
f. Low battery
Battery back -up for minimum 5-6 hour
Should fix, on rails of transport trolley and on stand with
wheels.
System Configuration Accessories, spares and consumables
Main Ventilator unit -01
Adult Reusable /Autoclavable Silicon Patient Circuit with
expiratory valve -01
Pediatric / neonatal Re-usable /Autoclavable Silicon Patient
Circuit with expiratory valve -01
Oxygen Hose-01
Power supply unit / battery charging unit
power supply cable for 12 V DC
Environmental factors
The unit shall be capable of being stored continuously in
ambient temperature of 0 -40 C and relative humidity of 1590%
The unit shall be capable of operating continuously in
20
ambient temperature of 10 -40deg C and relative humidity of
15-90%
Shall meet IEC-601-1-2 EN 1281-1, IEC 601-1-1, EEC 93/42 ,
EN 749-3
Class 1 Type B
Power Supply
Power input to be 220-240VAC, 50Hz
Standards, Safety and Training
Electrical safety conforms to standards for electrical safety
IEC-60601
Product should be FDA/CE
Manufacturer and supplier should have ISO certification for
quality standards.
Warranty for 2yrs
and provision of CMC for next 3 years.
Documentation
User Manual in English
List of Equipment available for providing calibration and
routine maintenance support as per manufacturer
documentation in service / technical manual.
4
Ventilator (Adult):Description of Function
ICU ventilators should provide artificial respiratory support
to the critical patients in all the types of Intensive Care Units
with altitude compensation for volume and BTPS correction
for monitoring.
Operational Requirements
It should be microprocessor Controlled ventilator with
integrated facility for Ventilation monitoring suitable for
Neonatal (including premature) to adult ventilation.
The unit should be external compressor based for precise gas
delivery ( not a turbine / piston/ blower based internal
compressor ) .It should have proximal flow sensor for
neonatal patient category only . Demonstration of the
equipment is a must.
Technical Specifications
Hinged arm holder for holding the circuit
Should have Colored Touch screen, 12 Inch or more
It should have inbuilt facility to measure and display for all
patient category ( Adult to neonatal )
3 waves- Pressure and Time, Volume and Time and Flow and
Time., Co2 and Time
3 loops- P-V, F-V, P-F with facility of saving of 4 Loops for
reference. Also facility to display valumetericcapnography
loops
Graphic display to have automatic scaling facility for waves
Status indicator for Ventilator mode, Battery life, patient
20
data, alarm settings, clock etc.
Simultaneous display of SET and exhaled parameter , 3
waveform and 2 loops and Alarm
Should have Trending facility for 72 hours
Should have Automatic compliance & Leakage compensation
for circuit and ET tube with ET Tube size and % of
compensation
Integrated( in main unit )Mainstream End tidal CO2 with
Capnography with monitoring of PeCO2, Vmin VCO2, Curve
Co2/ time, Alveolar ventilation , expire Co2 ( VTCo2) ,VHigh
and Vlow alarms etc. external Etco2 monitor will not be
accepted. Meanstream EtCo2 Sensor - 1no reusable Adult
/ped, neonatal adaptor - each 1 .
Should have following settings for all age groups.
a) Tidal Volume 5 ml to 1800 ml
b) Pressure (insp) 2- 90 cmH2O
c) Pressure Ramp/ Flow patterns
d) Respiratory Rate 1 to 150 bpm, Insp. Time 0.1 to 9 sec, I :
E Ratio 5:1 to 1:5
e) Insp. Flow ( resultant) 0.3 to 180 LPM, continuous Flow 238pm ( in TCPL ode)
f) CPAP/PEEP 0-45 cmH2O
g) Pressure support 2-80 cmh2O
h) FIO2 21 to 100%
i) Pause Time 0 to 2 sec
j) Flow Trigger 0.2 to 12 lpm . Pressure Trigger 0.5 to 15
cmH2O
k) Expiratory trigger or exhalation sensitivity - 5-75-% of flow
Should have monitoring of the following parameters
a) Airway Pressure (Peak & Mean)
b) Tidal volume (Inspired & Expired)
c) Minute volume ( Expired)
d) Spontaneous Minute Volume
e) Total Frequency
f) FIO2 dynamic
g) Intrinsic PEEP and PEEPi Volume (or trapped Volume)
h) Plateau Pressure
i) Resistance ( Rinsp&Rexp)& Compliance ( Cdyn&Cstat)
j) Use selector Alarms for all measured & monitored
parameters
Should have following modes of ventilation
a) Volume controlled
b) Pressure Controlled
c) Pressure Support
d) SIMV (Pressure Control and volume control) with pressure
support
e) CPAP/PEEP, PSV + assured tidal volume / guarantee /
volume support
g) Advanced mode like pressure controlled volume
guaranteed / PRVC / AUTOFLOW
h) Non Invasive ventilation ( NIV Mode )
i) Additional mode advance ASV / NAVA / MMV+ PSV /
j) APRV
k)Special Neonatal modes - Yime cycled pressure limited
with continuous flow (TCPL) , SIMV +TCPL + PSV, N-CPAP(
with continuous flow) , PRVC,APRV,and above mentioned
mode
Should have Apnea /backup ventilation. Back up mode
should user adjustable and bi directional (auto switch over
from spont. to control and vica-versa
Expiratory block should be autoclavable and no routine
calibration required
Should have, monitoring of the following parameters
a. Intrinsic Peep & Intrinsic PEEP Volume (Trapped Volume)
b. Occlusion Pressure( P0.1) , Max Inspiratory pressure (Pi
max)
c. Non-forced Slow Vital Capacity , physiologic Dead space,
RSBI, Imposed work of Breathing ( WOBi), Expiratory Time
constant ( Tcexp)
d. Facility to calculate lower and upper inflection point ( P/V
Flex points)
e. Facility for ET Tube compensation with tube diameter (
4mm onward) and % of compensation and Patient circuit
compensation
Should have integratedNebulizer with capability to deliver
fine particle size of to be used in On line
Should have Ideal Body Weight facility
Should integrated Battery backup for minimum 2 hour for
main unit
RS 323C interface for communications with networked
devices.
System Configuration Accessories, spares and consumables
ICU Ventilator with trolley - 01
Adult , Pediatric , Neonatal autoclavable silicone patient
breathing circuits -02 each
Reusable and autoclavable Flow sensor and exhalation
valve/ expiratory cassette - 4 nos each. The expiratory flow
sensor and valve should have 2 years replacement warranty
Proximal Flow sensor for neonatal use - 10 nos
Hinged Support Arm - 1no
Air and Oxygen Hose - each 1 no
Medical Air Compressor with CE mark
Reusable Masks (Small, Medium, Large) with each machine.01 sets ea
Humidifier -Servo controlled fisher and paykel MR 850 with
digital monitoring of inspired gas temperature -01 .
All accessories required like temp. Probe, heating wire, draw,
chamber etc - each 2 nos.
Inlet requirement
Power input to be 220-240VAC, 50Hz
Gas input( air and oxygen) - 50-100 psi
Standards, Safety and Training
Should have US FDA and CE for main ventilator unit for all
the feature mentioned the specification. The company
should attaché valid 510K and US FDA certificate along in the
technical bid.
Demonstration of quoted equipment model is a must.
Should have local service facility .The service provider should
have the necessary equipment service set up recommended
by the manufacturer to carry out preventive maintenance
test as per guidelines provided in the service/maintenance
Warranty for 2yrs &provision of maintenance for next 5yrs
ANNEXURE XIII D
SPECIFICATIONS & DETAILS OF ITEMS
GROUP (D)
Sl
Specifications
QTY
(Nos)
1
217
Shadow less Light 19” dome. :Lamp mounted on four legs heavy duty base fitted with 75mm dia
castors
2 Halogen bulbs of 24V – 50W are used. 1 for main and other as
backup
Light Intensity 90000 lux +/- 10%
Color Temp 4300 k
Light field diameter 120mm or more
Dome Diameter 19”
Power Supply AC 220-230V/50-60 HZ
Should be CE ,ISI/GMP,OHSAS 18001:2007,ISO 9001:2000,ISO
14001:2004
&13485:2003 certificates.
Warranty for 2yrs
2
153
Binocular Microscope (Electric) :Binocular Compound Microscope with Infinity Optical System
(IOS)
Illumination: Koehler Illumination system with Built-in 6V-20W
Halogen with intensity control regulator.
Focusing Module: COAXIAL coarse & fine focusing mechanism,
with tension control ring. Ergonomically designed for easy grip,
esp. for tension control.
Nosepiece: Inward Tilt Low friction & fully Parfocal Quadruple
Revolving nosepiece (Ball bearing type).
Viewing Head: Siedentopf Binocular tube, inclined at 30°
rotatable through 360° with IPD 48-75 mm and Dioptric
adjustment. Anti fungus treated
Stage: Double layer graduated mechanical rectangular stage size
142 x 133mm cross travel 75 (X) x 50 (Y) mm on ball bearing coaxial controls spring clip double specimen holder Condenser
Moveable ABBE Condenser, NA 1.25 with aspheric lens. Iris
diaphragm special day light blue filter in holder
Objectives
IP series DIN Infinity Plan Achromatic, Anti fungus treated
objectives:
4x/0.10, 10x/0.25, 20x/0.40, 40x(SL)/0.65, 100x(SL, Oil)/1.25
Eyepieces: Wide Field eyepiece WF 10x/18mm paired with eye
guards Power Input 220V AC, 50Hz as per ISO 9001, CE standards.
Standard Accessories: Packed in Moulded Styrofoam box with:
Operation Manual, Cleaning Cloth Dust cover
Warranty for 2yrs
3
206
Haemoglobinometer :· Fast & precise measure of Hemoglobin and Hematocrit in
whole blood.
· Should have an option of Hematocrit value in case of normal
Hb limit
· Measurement at two wavelengths, 570 nm & 880nm
· The machine should have an option of setting the cut off
range of flag the extremely higher and lower values.
· Should have user friendly Graphical Touch Screen Panel.
· Analyzer automatically stores up to 100 results with date,
time and sex
· Automatic self-test
· Measuring range 0-256 g/L (0-25.6 g/dl,0-15.9 mmol/L)
· Measuring time- Less than 60 secs
· Analyzer should have in-built re chargeable battery with 100
hrs back up.
· Quality control Curvettes to be provided for QA.
· PC and printer connectivity option
· Calibrated against the international reference method for
hemoglobin determination.
Warranty for 2yrs
4
234
Glucometer with 100 Strips:Biosensor/ Electrochemical, Glucose Oxidised (GOD) method
Highly Certified: US FDA, Health Canada and CE
Sample type should be fresh whole blood (capillary). Primary
site should be finger tips and alternative site should be
Forearm & Palm.
Hematocratic range is 30 – 55%.
Individually foil wrapped test strips should be available – each
strip should be protected from contamination, oxygen, high
temperature and high humidity to ensure stability and high
performance.
Wide range operation temperature. The temperature
detection and compensation feature should allow ranges of 545°C. Operating humidity range is 10-90 %.
Meter should include lithium battery life up to 1000
measurements.
Glucose test range from 20 – 600 mg/dL.
Great Data Management. Meter should record up to 300 tests
with time, date. Test averaging 7,14,30 days average.
Extended expiry period for strips up to approximately 24
months
End fill strips with wicking action should make blood
application as easy as touching the strip to the sample, along
with fast sip-in action.
Sample just 1µl.
Test results should be able to be obtained in only 10 seconds.
Code chip should allow for automatic calibration.
Meter automatically should powered on or off after test strip
inserted/ removed.
Beep sound should occur to notify the user when test strip
inserted, sufficient blood sample is applied and when testing is
completed.
Results should be plasma equivalent which can be compared
directly with lab analyzer results if required.
Warranty for 2yrs
5
234
Water Bath:With electronic control , LED Display,
Button to set nominal value in 0.1ºC.
Temperature Range 5°C above ambient room temperature to 100
ºC,
External W : 500 X D: 250 X H: 300 mm (approx)
Bath Capacity: 20 Ltrs (Approx)
Temperature Accuracy: + 0.1 ºC
Body of the equipment should be of material which is rust free
from both inside and outside.
Warranty for 2yrs
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003 certificates.
6
234
Hot Air Oven:Size: 45 x 45 x 45 cm
Door/Shelf: Single Door with 2 shelves constructed
To give uniform and adequate sterilizing temperature Range
adjustable up to 200 ºC with digital temperature Display, stainless
steel and rust free.
Material: Door fitted on heavy brass chrome plated hinges
Cabinet: Cabinet double walled mild steel
Insulation: Minimum Thickness 5 cm of glass wool
Finish: Inside the cabinet heat resistant finish and Outside
durable, rust free
Air Circulation: Ventilated with internal fans to assist Circulation
of air
Warranty for 2yrs
7
234
Lab Incubator:Incubator Bacteriological (Memmert type) reliable day to day
operation in variety of uses. Drying of slides, paraffin embedding,
tissue culture work, incubation of antibody test, excellent for
Microbiological determinations, crystallization studies and
Incubation of hydroxy steroids.
Construction :–
with double walled construction with complete inner chamber
made of Anodized Aluminum or Highly Polished Stainless Steel.
Outer chamber is made of Mild Steel Sheet, finished with powder
coated paint. 75 mm gap between the walls is filled with special
grade glass wool for proper insulation and to avoid heat losses.
Inner chamber fabricated with ribs for adjusting shelves to
convenient height.
Supplied with 2 or 3 removable shelves. SHELVES made of fully
Anodized Aluminium Sheet or Polished Stainless Steel Sheet as
per chamber.
Door insulated & fitted with heavy hinges. Door Double glass
window which facilitate inspection of samples without opening
the door. Heating elements, made of high grade imported
nichrome wire are put inside the porcelain beads and placed at
the bottom and side ribs for uniform temperature all over the
space.
Temperature Control: – by imported capillary type thermostat
from ambient to 80°C. Temperature control knob graduated in
centigrade degrees after actually observing the temperature in
steady state. fitted an L-shaped prismatic glass
Thermometer on top of the Incubator for reading the chamber
temperature.
With Ventilation: – Control Panel having a thermostat control
knob, ON/OFF switch and two pilot lamps.
Power Requirement: – Supplied with cord and plug suitable to
operate on 220 V single phase, 50 Hz, AC supply.
Size
of
inner
chamber:–
Inner
Chamber
W
x
H
x
DS.S.
(304
grade)
455 x 605 x 455 mm
Filled with Air Circulation Fan
Optional Accessories & spares to be quoted
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003 certificates
Warranty for 2yrs
8
Domestic Refrigerator:Capacity
400
Gross
Total : 195L
Refrigerator : 195L
Net
Total : 185L
Refrigerator : 185L
Physical Specification
Weight
Net : 37kg
Gross : 41kg
Dimension
Net (WxHxD) : 534 x 1,250 x 540mm
Net Case Height with Hinge : 1,250mm
Net Case Height without Hinge : 1,250mm
Net Depth with Door Handle : 540mm
Net Depth without Door Handle : 540mm
Performance
Energy consumption
255 watts
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003
certificates
Warranty for 2yrs
9
Radiant Warmer :-
50
OPEN NEWBORN CARE SYSTEM ON TROLLEY,WITH RADIANT
WARMER, OXYGEN-PROVISION
Technical Specifications:
Mobile newborn resuscitation table with fixed-height radiant
warmer
Antistatic castors, 2 with breaks
Table surface with mattress, head up/down facility, X-Ray
cassette holder.
Mattress-padding: foam density approx. 21 - 25 kg/m3
Mattress cover should be sealed and waterproof.
Side boards transparent acryl, drop down and lockable
Side rails allow for mounting of accessories with SS Height
adjustable infusion rod.
Hood suspended above the table integrates heating element and
overhead spot light
Integrated support for two 10 L oxygen bottles
Control unit should have flow meter, Humidifier bottle and FA
Valve with pressure gauge
Heating element: Ceramic heater - 650 W (lifelong warranty)
mounted in parabolic reflector and protected by metal grid
Control unit allowing air and skin temperature preset (LED
indicator)
and drives radiant heater output (Skin Servo OR Air control OR
manual mode)
Integrated timer: 1 to 59 min, with count-up and count-down
feature
Temperature range, skin: 34 to 38°C (user pre-settable)
Monitoring of skin temperature by means of sensor, range: 30 to
42°C
Heater output: 0 to 100% in increments of 5%
Control unit: audiovisual alarms according to timer and
temperature preset avoiding overheating
Should be able to display reports systems errors, sensor failure
with message on LCD.
Power requirement: 220 V/50 Hz
Power consumption: 800 W
Device should be produced by ISO 9001 certified manufacturer
(Certificate to be submitted)
Device should be safety certified according ISO & CE(93/42)/ FDA
510k
Should be supplied with:
1 x spare skin temperature probe (including connection cable)
2 x empty 10 L oxygen cylinders
1 x spare set of fuses
User manual with trouble shooting guidance, in English.
Technical manual with maintenance and first line technical
intervention
instructions, in English
List of priced accessories
List of priced spare parts
List with name and address of technical service providers in India
Training and installation at end-user site
Proposal for full service AMC, for five years after completion of
guarantee period,
covering (i) 2 preventive maintenances per year,
(ii) on-call technical interventions, spare parts and travel
Warranty for 2yrs
10
Feotal Doppler:
1. Should be portable with a carry bag.
2. Should be able to work on mains as well as on 9 volt single
battery.
3. Should have facility for tape recording.
4. Should have ear phone facility.
5. Should have heart beat indicator.
6. Should have totally soft touch panel.
7. Should have battery indicator.
8. Should possess low battery indicator.
Warranty for 2yrs
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003 certificates
50
11
242
Electric Suction Machine:Suction machine foot cum electric model with 2 separate
suction systems,
electric & cabinet made of mild steel epoxy powder coated,
with 2 vaccum gauges 700 mm/Hg
Volume: 25-30 Ltrs/min (Jar Capacity 3 Ltrs), 2 graduated
polycarbonate suction jars each of 1.5 ltrs capacity self sealing
rubber lids with synthetic rubber lids, long pressure tubing,
heavy vertical foot pump, vacuum control , automatic overflow
cut off device, mounted on 4 rubber castors.
Sound: 45 db A+ 3
As per ISI Marked No. IS: 4533, SS Top, Epoxy Powder Coated
Finish
Warranty for 2yrs
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003
certificates
12
88
ECG Machine with adult, paedeatric and neo natal leads:Technical Specification of Single Channel Automatic ECG
• Single Channel ECG Recording.
• Last Memorized ECG recording & additional copies
available.
• Automatic and Manual recording modes.
• Dual Power Supply: Mains and battery Operation.
• Thermal Printing on 50 mm paper.
• Compact design, light weight& portable.
Warranty for 2yrs
13
88
Ceiling OT Light (shadowless) (UNITED)
• The multi – reflector shadow less ceiling Lights should be used
•
14
halogen lamps with heat observe filters to give “cold” with
light, which should be ideal for modern surgeries, The Lights
should have incorporational safety standards like CE Mark, ISO
9000 quality standards
Technical Data
• Intensity (In Lux): - 130,000
• Colour Temp.: - 4300K
• Halogen Bulb: - 7 x 24V-50W*
• Light Field Diameter: - 120mm or more
• Dome Diameter: - 710mm
• Input Voltage: - AC 220-230/50-60HZ
Warranty for 2yrs
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO
9001:2000,ISO 14001:2004 & 13485:2003 certificates
69
Boyles Apparatus with vaporiser and standard accessories
The Anesthesia Machine should be of 2 Gases with 2 tubes
Hypoxic Guard Including Circle Absorber..Machine must be made of rigid & electro statically powder
coated steel with antistatic Castors with front brakes.
• Machine should be equipped with 2 Nos. High Pressure
outlets for driving ventilator.
• Machine must have Oxygen Flush with 32 to 59 LPM
flow or better.
• The machine must have flow meter for oxygen and
nitrous oxide supply with adjustment controls. Oxygen
Flow meter can be calibrated from 100 ml to 8 Liters
and for Nitrous Oxide from 200 ml to 12 liters per min.
• Machine should have pneumatically controlled
integrated Hypoxic Guard/ORC ensuring that a
minimum range of 25%-35% oxygen can be run through
the machine as per requirement (25% can be set) .
• The machine must have inbuilt Oxygen Failure Warning
Alarm.
• Machine has a common gas outlet Male and Female
Type, size to specify.
• Machine should have provision for connection to
pipeline supply for Oxygen and Nitrous Oxide Supply.
Once pipeline supply is turned on machine should be
able to use pipeline supply and cylinders supply be kept
as reserve and incase of pipeline failure only cylinder
supply can be turned on. Separate indication gauges for
Pipeline and Cylinder Pressure.
• Machine must have a system pressure relief valve to
protect from backpressure. The valve set at normal
pressure of 200 cm of H20.
• Provision for mounting 2 Nos of Bulk Cylinders on the
extended rear platform & top tray for mounting
monitor at eye level.
• Machine has gas specific pin indexed cylinder yokes
with sliding stainless steel clamping bars for easy
handling. Two each for oxygen and nitrous oxide
cylinder with 5 liters capacity.
There should be individual pressure regulator on each
circuit output phase of 4 kg/cm² and Capable of
delivering low flow Anesthesia
• Provision for mounting of ventilator on the side, writing
table and pre-use operative checklist and two closed
drawer for keeping essential accessories.
• Machine must be supplied with twin canister circle
absorber. The absorber has switch control to switch
between Automatic and Manual mode of ventilator.
• One Set of Essential Accessories with item wise rate
should be quoted as option without which the
quotation will be rejected.
• The supplier has adequate service backup with service,
availability of on-self spares and calibration equipment
in north east.
• Vaporizer for Halothane/Isoflurane to be compulsorily
quoted as optional.
• . CE Certified and ISO 13845 Certified
Warranty for 2yrs
•
15
89
Defibrillator.Technical specification of Bi-Phasic defibrillator with AED
1. Should have Current controlled Biphasic waveform
technology
2. Should have a facility of at least 100 charge /Discharge of
300j in a single charge
3. Should be equipped with AED with Voice and Visual Prompts
4. There should be facility of Voice guided CPR
5. At least 24 events storage capacity
6. Should have a facility of Momentary AED ON/OFF key on
front panel to enter and exit AED mode
7. Energy selection dynamic range should be 2j to 300j or
above
8. Should be able to record ECG before and after shock
10. Should have thermal printer facility
11. Should have ECG R wave Synchronous or Asynchronous
Mode
12. Should have charge ready indication with Display and Voice
Command
13. Should have Adult and Pediatric paddle integrated into
Same Handle (Swipe to Expose)
14. Should be ISO 13845 Certified.
Warranty for 2yrs
16
75
Surgical Diathermy:Modular design, Integrated Patient Control System (PCS).
Independent activation of monopolar and bipolar output.
Should have time controlled cutting mode
Should allow monopolar cutting and coagulation by using both
foot switching.
Should have bipolar coagulation option.
The system should automatically adjust to given tissue
impedances.
Monopolar Pure cut should be suitable for under water cutting
(TURP, TUVP & TCRE) with URO-CUT, which eliminates lag time in
initiating cut especially suited for urological procedure.
a) Three Blend – modes (program)
b) Low Cut – Endocut (Gastrocut) – for G.I Surgery
Should have Monopolar coagulation –Soft mode (lap, desiccation)
Forced mode (Standard), Spray mode (for non contact large area).
a)Desiccation/Soft – for low voltage soft coagulation suitable for
laproscopic& delicate tissue work.
b)Fulgurate/Forced – non contact coagulation for minimal smoke
generation
c)Spray for non-contact large tissue area coagulation with
minimum depth of necrosis
Should have Bipolar- Micro (for delicate tissue without charring,
adhesion and blanching), Coagulation (high current low voltage
pulsed bipolar, also suitable for vessel sealing system
Range of accessories should provide extensive selection of
handles for various application e.g. needle, ball, spatula type.
Accessories- Ergonomically designed trolley to house cautery
(Small,. Light and Portable), Monopolar cord (at least 6), bipolar
cord (at least 6) selection of handles, footswitches (all other
standard accessories).
bipolar cord (at least 6) selection of handles, footswitches (all
other standard accessories).
Warranty for 2yrs
Should be ISO Certified.
17
101
Fumigation Machine 5 Ltr capacity:Specification:Max. height : 390 mm , Weight : 8.5 kg (Approx.)
Atomizing Capacity : 30-50 ml/min
Should be available with timer.
Warranty for 2yrs
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,ISO
14001:2004 & 13485:2003 certificates
18
20
Horizontal Sterilizer:Inner Chamber should be made up of thick sssteel of 304 / 316
quality and jacket is made out of rolled s.steel.
Single door should be made of rolled steel lined with S.S. sheet
has radial locking system.
All units is to be hydraulically tested up to 40 psi. The space
between outer cover made of thick rolled steel sheet and the
steam jacket filled with mineral wool. Boiler should make of thick
S.S.sheet and is located under the sterilizer. It should be fitted
with water level indicator, safety valve, pressure gauge, and
water inlet and drain valves. Unit to be fitted with low-water cutoff device and automatic pressure control device.
Fitted with self-locking safety door device.
Two separate valves should be provided for evacuating steam
from inner chamber and jacket, as and when desired. The
sterilization cycle should be controlled through multiport valve or
three-way valve. Fitted with a dial thermometer and automatic
vacuum breaker. To work on 440 volts, 3 phase, A.C. supply.
Warranty for 2yrs
Should be CE, ISI/GMP, ISO 9001:2000, & 13485:2003 certificates
19
20
Vertical Autoclave with dressing drum:It is to be used for sterilization under saturated steam pressure at
any selected point between 5 to 20 p.s.i. (adjustable). Should
have double walled units with inner chamber (Boiler) made of 18
S.W.G. stainless steel and outer chamber is made of SS sheet
covered with S.S. Lid with radial locking system. Fitted with
neoprene rubber gasket, all systems are hydraulically tested up to
40 p.s.i. as a safety measure. All autoclaves are to be fitted with
standard accessories such as water level indicator, pressure
gauge, steam release cock, spring-loaded safety valve and heating
element. Should be supplied complete with S.S. basket and
vacuum breaker device, cord and plug, to work on 220/230 volts
A.C. Supply. Capacity: 22, 40, 50, ltr. Should be Supplied with
dressing drum.
Warranty for 2yrs
Should be CE, ISI/GMP, ISO 9001:2000, & 13485:2003 certificates.
20
50
PHOTOTHERAPY UNIT, SINGLE HEAD, HIGH INTENSITY :Technical Specifications:
Heavy sturdy mobile stand phototherapy unit
Antistatic castors, 2 with breaks
Head height adjustable, approx.: 0.95 to 1.40 m
Blue light, 4 Compact Fluorescence Tubes (CFL), approx.: 20 W
White light, 2 Compact Fluorescence Tubes (CFL), approx.: 20 W
Tubes are to be protected by grill
Irradiance at skin level, > 25 uW/cm2/nm
Wavelength: 420 to 500 nm, with highest intensity at 470 nm
Integrated cumulative Dual Digital timer for Tube light usage and
Patient
Power requirement: 220 V/50 Hz
Power consumption: 250 W
Device is to be produced by ISO 9001 certified manufacturer
(Certificate to be submitted,)
Device should be safety certified according ISO & CE (93/42) / FDA
510k
Should be supplied with:
2 x spare blue CFL tubes
1 x spare white CFL tube
1 x spare set of fuses
User manual with trouble shooting guidance, in English
Technical manual with maintenance and first line technical
intervention instructions, in English
List of priced accessories
List of priced spare parts
List with name and address of technical service providers in India
Training and installation at end-user site
Proposal for full service AMC, year 1 to 5, covering
(i) 2 preventive maintenances per year,
(ii) on-call technical interventions, spare parts and travel
Warranty for 2yrs
21
Oxygen Concentrator:With in-built oxygen purity sensor.
50
If the oxygen purity comes down below 85% audio visual alarm
gets activated.
Oxygen Concentrator to provide oxygen from air with Oxygen
purity monitor.
Sound Level < 47 Db with best quality superior grade molecular
sieve, maintenance free
Rotarypopet valve. Oxygen purity not less than 90-96% with
oxygen output 5 Ltrs
per minute and pressure 8 Psi minimum. With double outlet and
oxygen tubes of
2 mtrs length. 2 Humidifier Bottle & 2 Cabinet filter.
Power Requirement 220V/ 50Hz.
Latest ISO 9001 Certificate and FDA 510K and CE Certificate to be
attached.
Supplied with:
1 Spare set of tubing
1 x spare internal & external bacterial filter
1 x spare set of fuse.
User Manual with trouble shooting guidance in English
Technical Manual
Training installation at user site
Warranty for 2yrs
22
50
Examination Light:Description of Function:
Mobile operating light is required for doing surgeries in an
emergency environment and the system can be moved from
place to place.
Technical Specification:
Mobile light for medical examination.
Stand with 5 anti-static swivel castors.
Articulated arm 105 cm, spring loaded, with on/off switch and
integrated transformer.
Arm: Moulded plastic arm.
Dome: Unbreakable poly carbonate dome with reflector.
Dome rotation : 360 degree
Halogen bulb: 12V/50W
Light intensity approx.: 30,000 Lux at 40 cm Natural white light.
Eligibility Criteria:
Should be FDA OR CE approved product.
Manufacturer should be ISO certified for quality standards
Should have local service facility.
The service provider should have the necessary equipment
recommended by the manufacturer to carry out preventive
maintenance test as per guidelines provided in the
service/maintenance manual
Warranty for 2yrs
23
50
Infantometerplexi, 3½ft/105cm:Portable baby/infant length- height measuring system
Measures laying length of neonates and babies
No need for calibration as all parts have prefixed position
Reads in centimeters and inches
Minimum graduation: 1 mm
Long-lasting hard-wearing ruler/graduation is fully integrated with
device
Measuring slide/wedge glides smoothly and close via ruler,
avoiding reading parallax
Measuring slide/wedge wobbles max 2 mm, over full length
No sharp edges or corners
Long stable board, width: ca 30 cm
Length, measurement range, approx:100 cm
Head/footplate, board and slide/wedge should made of quality
laminated wood or plastic
Wood parts should be treated and finished/protected with
varnish to prevent chipping of edges and allow easy cleaning; all
connections should screwed/nailed plus glued
Device is to be produced by ISO 9001 certified manufacturer
Should be supplied with:
User manual with trouble shooting guidance, in English
List of priced accessories
List of priced spare parts
Warranty for 2yrs
24
50
Electronic Baby Weighing Machine 10 kg <5g> :• Electronic scale for weighing babies with Polycarbonate Pan
• Measuring range 0 to approx. 10 kg
• Minimum graduation: 5 g
• With tare function
• On switch and auto-off
• Auto-calibration with each switch-on
• Large LED display readable in low light working situations,
display cover durable plastic
• Display in kg and lbs., easy switch between kg and lbs.
• Reading time max 5 seconds
• Zero weighing adjustment
• Temp Hold Facility
• Smooth surface/finishing allows for easy cleaning/disinfection.
• All vital parts made of rust proof materials
• Horizontal leveling with height adjustable feet
• Splash proof and shock resistant light-weight body
• Power requirements: 220 V / 50 Hz
• Device is produced by ISO 9001 certified manufacturer
(Certificate to be submitted
CE/FDA/BIS approved product)
Supplied with:
1 x spare set of fuses
• User manual with trouble shooting guidance, in English
• Technical manual with maintenance and first line technical
intervention instructions, in English
• List of priced accessories
• List of priced spare parts
• Warranty for 2yrs
25
Foot Suction :Max negative pressure valve : > 0.08MPa
Negative Pressure Back-reduction while being closed.
<0.005MPa/10 min
Reservoir Capacity :- 1000 ml
Pedal Pressure : < 245 N
Warranty for 2yrs
CE/FDA/BIS approved product)
50
26
50
Pulse Oxymeter (Baby):Should have facility to display PR & SpO2 as standard parameter
and within built rechargeable battery backup of at least 2 hours of
operation.
Color TFT display of size 7” or more
Should have reliable and proven SpO2 technology to sense the
SPO2 in hypotensive, shivering & motion condition, facility
Should be able to store & display at least 24 hrs of trends
Suitable for monitoring adult, Pediatric & neonatal patients, able
to give visual & audible alarms
Should have low battery indicator
Should have optional CNS connectivity
Should have Real Time clock
Warranty for 2yrs
27
Syringe Infusion Pump :Fully Microprocessor controlled
Mains cum battery operated with built in battery and charger
Should accept syringe size from 10ml to 60ml
Should have Micro mode and continuous injection mode
should be compatible with all major Indian and Foreign brand
syringes
Should have flow rates from 1ml / HR to 1200 ml/HR
Should have high accuracy
Should have adjustable bolus facility
Bolus rate up to 1000ml/HR with 50/60ml syringe
Should have 3 level occlusion pressure setting
Should have audio visual alarm
Should have battery backup up to 4 Hrs.
50
should have anti reverse function to prevent upstream
should have double CPU to ensure safety and reliability of
infusion
Warranty for 2yrs
28
50
C-PAP :Should be suitable for neonatal patients.
Should provide flows of a heated and humidified Air and O2
mixture under controlled pressure, by water and bubble column,
providing a Continuous Positive Airway Pressure in non-invasive
mode. Should have good quality calibrated blender for mixing of
Air and Oxygen US FDA approved. It should have digital
temperature indicating with at least 10 heating levels. Humidifier
should have water level sensor with audio visual alarms and
pressure relief valves. When an occlusion pressure occurs in the
inspiratory branch, the circuit relief valve should limit the
pressure excess in the line. It should be designed to operate with
a pressure of 17cmH2O at flow of 5L/min.It should have O2 and
Air pressure regulator valves with manometer to control the input
pressure up to 3.5Kgf/cm2 and to protect the patient circuit.
Blender output should be equipped with a flow meter. Should
have relief valve to guarantee pressure to the system. Delivery
system should have maximum input flow of 15l/min. CPAP
pressure minimum should be 0 to 10 cmH2O. FiO2 concentration
should be adjustable from 21% to 100%. All parts should be
managed on a strong trolley type stand along with an IV pole.
Temp. sensor which is to measure the temp. of the humid air
should not be more than 2 inches away from the patients nostrils.
The supply should be made with 5 kits with the BCPAP. The
delivery kit should contain all the consumables needed for BCPAP.
Each Kit should have Nasal Prong - 1 no., Bonnet - 1 no., Blue
corrugated Tube - 1 no., Transparent Corrugated Tube - 1no.
Elbows - 2 nos.
Should be BIS/US FDA/ EUROPEAN CE approved.
Warranty for 2yrs
29
Baby Incubator:-

The unit shall be useful for treating premature an low birth weight
babies.

The salient features to include maintenance and control of
temperature and Humidity in the baby compartment for safe neonatal
care.

The design to incorporate all controls include microprocessor
based servo controller for temperature control and to have digital display
on the front panel, with dual colour digital display for Skin and Air
temperature indication separately.

Temperatures setting from 30ºC to 39.9ºC.
50

The unit shall be incorporated with all he safety features on any
malfunction or emergencies like power failure, High temperature etc.

The mechanical features should include clear canopy for visibility
with front door opening and four port holes all over for easy handling of
the baby in the canopy, flat perplex base without any dents for easy
cleaning and disinfection control to be provided with a large mattress
platform ,suitable to tilt a desired angle, built in X-ray cassette tray.

The unit shall be mounted on a trolley fitted with suitable castors
with breaks for the mobility and to have utility drawers for storing the
emergency kits, baby needs and accessories.
Warranty for 2yrs, Should be CE & ISO Certification
30
Nebuliser :Nebulizer Nebulization Rate……… 3cc H20/8-11 minutes.
Maximum Compressor Pressure… 25 psig by relief valve setting.
Maximum Operating Pressure………11-15 psig
Free Air Flow……………………… 10 lpm.
Compressor Type……………………Piston
Electrical Requirements…………… 230V , 50 Hz-0.7 amps
Power Consumption……………… 70 walts
Weight………………………………1.3 kgs
In built thermal fuse for optimum safety
Warranty for 2yrs
31
32
Vibration free refrigerator with servo voltage stabilizer:Suitable for the primary requirements of every blood bank and
hospital, to preserve and secure the vital supply of blood, plasma
and other blood derivatives Mounted on a study angle frame the
inner chamber is made up of S.S. and outer of M.S. duly enamel
painted. The temperature should be maintainable at 4° C to 6° C
for storing blood bottles or blood bags. Temperature should be
controlled by Solid State Digital Indicator-cum-controller which
triggers the Audio Visual Alarm in the event of fluctuation
exceeding permitted tolerance. Unit should also fitted with door
operated alarm and power supply failure alarm, as a safety
device. Drawers are to be provided for 85 bags. The refrigerator
should be vibration-free and supplied with servo voltage
stabilizer.
Should be CE, ISI/GMP, ISO 9001:2000, & 13485:2003
certificates.
Warranty for 2yrs
32
Patient monitor system: (Should be of modular type and capable of
monitoring adult, pediatric & neonatal patients.)
Monitor should have minimum 12” T.S. display.
Should be capable of 6 traces display.
50
89
Monitor must be capable of simultaneously monitoring the
following
parameters which should be present as standard: ECG, NIBP,
SpO2,
invasive pressures (4), temperatures (2)
Should be upgradeable to monitor Cardiac output, SvO2, 4
channel
direct EEG, capnography and BIS. Prices to be offered optionally
ECG should have capability for 3, 5 and / or 10 lead monitoring
and
should have built in arrhythmia monitoring on all leads.
Inbuilt ST segment analysis and arrhythmia detection for all the
leads should be possible.
Hemodynamic and drug dose calculations should be available.
Arrhythmia should be grouped based on classifications – and
should show no of arrhythmias occurred.
Respiration should be available with Cardio Vascular Artifact
filter.
OCRG should be available for monitoring neonates.
ICP monitoring should be possible.
Alarm parameter should flash red in the presence of high priority
alarms (e.g. ventricular fibrillation and asystole) and flash yellow
in the presence of medium or low priority alarms (e.g. noisy signal,
etc.)
24 hours trend data should be displayed.
All monitors including central station should have similar user
interface for easy usage among all clinicians.
Monitor shall provide the capability to interact with alarms at
remote bedsides.
Monitor shall provide the capability to receive and display realtime waveforms, trended data and alarm status from other
bedside or telemetry units on the patient monitoring network.
Monitor shall provide the capability enter patient information at
the bedside or central monitor.
Alarm limit status (ON/OFF) must be indicated on-screen for each
parameter and actual parameter alarm settings must be displayed
on-screen when alarms are on.
Should have internal rechargeable battery with back up of one
hour
Position of the displayed waveforms must be user configurable.
Waveform color changing should be user configurable.
Monitor shall permit the optional ability to receive and display
information from other patient devices such as ventilators,
infusion pumps and other standalone devices.
All modules should be compatible with all monitors quoted.
Bed to bed communication between the monitors should be
possible with out a central station.
Networking to central station should be possible.
Patient monitoring network shall use standard TCP/IP protocol
and be capable of residing on hospital’s network infra-structure.
Should be compatible with HIS and should be HL7 compliant.
Monitor should have capability to accommodate remote viewing
of real time waveforms through internet.
Should have CE and FDA certifications.
Accessories and spares
1. ECG / respiration: 5 lead ECG cable and lead wire set
2. NIBP: Adult: 1 sizes and Pediatric 1 sizes and neonatal, 1 size
per monitor
3. SPo2 Sensor: Adult sensor with cable, pediatric sensor with
cable
4. IBP: Include 10 no’s of disposable pressure transducer with
bracket and interface cable per monitor
5. Temperature: Skin and nasopharyngeal probes per monitor.
Warranty for 2yrs
33
154
Semi Auto Analyzer :Specifications:LIGHT SOURCE: Quartz-halogen lamp 12V-20W
WAVELENGTH RANGE: Automatic by 12 position filter wheel, 6
standard interference Filters; 340,405,505, 546,578 & 620 nm,
6 positions for optional Filters.
PHOTOMETRIC RANGE: -0.1 to 2.3 Absorbance.
DETECTOR: Photo Diode (320 – 1000 nm)
BLANKING: Automatic zero setting.
OPERATOR INTERFACE: Membrane keyboard for direct
function and alpha-numeric entry, Optional external keyboard,
High contrast graphical LCD display. Real time clock, 24 hours
system.
LANGUAGES: English.
MEASUREMENT PROCEDURES: Kinetic with linearity check,
Kinetic with linearity check, Sample slope blank, two point
kinetic with or without Reagent blank, End point with or
without reagent blank, Bichromatic end point with or without
reagent blank, End point with sample blank & with or without
reagent Blank.
MULTIPLE TESTING: Up to 9 replicates, Means, SD and CV.
MEASURING TIME: Programmable, 2 to 999 seconds for kinetic
& two point type of tests, For end point fixed at 2 seconds.
DELAY TIME: Programmable, 0 to 999 seconds.
METHOD PARAMETER SETTINGS: Method name, Measurement
mode, Wavelength 1 & 2 Aspiration volume, Measurement
delay, Measurement Time, Factor, Concentration standards,
Reagent blankly/n Sample blank y/n, Units of results, Levels for
flagging, Sample blank y/n, Units of results, Levels for flagging,
CALIBRATION: Factor, one point, two point, multi point.
Automatic on 1 standard (linear Mode), Automatic on up to 10
standards (nonlinear mode).
QUALITY CONTROL: Two controls per test, QC survey for ast 30
control measurements, Levey Jennings plot, High/Low flags.
KINETIC MEASURING TIME: Programmable, lowest 30 seconds.
TIME: Programmable, lowest 30 seconds.
TEMPARATURE CONTROL: By means of Peltier elements, fixed
temperature at 37 degree C
ASPIRATION SYSTEM: Internal pump of bellows type, driven by
stepper motor, back panel Connection for waste, aspiration
volume programmable.
Back panel Connection for waste, aspiration volume
programmable.
Back panel Connection for waste, aspiration volume
programmable.
QUALITY: UL; CE; CB certificate.
POWER REQUIREMENTS: 100 – 240 VAC nominal, 50/60Hz.
Battery back-up to retain data.
Warranty for 2yrs
34
35
154
Electricentrifuge, table top :The centrifuge should be suitable for high speed centrifuging
applications.
The equipment is to be provided with speed control, digital
temperature control cum indicator,
Digital timer with a range of 0-99 minutes and alarm at automatic
switching off, dynamic brake,
Zero start interlock, safety cut off in case of imbalance and lid
locking switch etc.
General Purpose Laboratory Centrifuge
Max. Speed RPM20000
Max. RCF x g34500
Max. Tube Size100 ml
Max. Capacity 400 ml
Warranty for 2yrs
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003 certificates
Spot Light
Intensity: 20000 ± Lux
Halogen Bulb: 12V – 50 W
Reflector: Metallic
Warranty for 2yrs
337
ANNEXURE XIII E
SPECIFICATIONS & DETAILS OF ITEMS
GROUP (E)
Sl
Specifications
Qty
(Nos.)
688
1
Patient's Examination Couch with Foot Step (Single).:Overall approx. size should be 1830mm L x 500mm W x
820mm H. minimum
Fixed upholstered top 50mm thick in two sections.
Body frame work should be made from 20G CRCA sheet.
Couch should be fitted with mild steel legs.
Headrest adjustable by gas spring.
Upper section of box approx. size 1200mm L x 450 mm W x
610mm H with three sliding drawers with separate doors.
Sliding foot step under the front side of lower middle cabinet.
B.P. apparatus tray made of 18G MS sheet of approx. size 350
mm L x 120mm W x 20mm H provided on a swinging rod
rotating through a bush fixed on the body of the couch.
Supplied with Single Foot Step.
All MS parts should be pre-treated in Seven Tank & Powder
Coated.
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO
9001:2000,ISO 14001:2004 & 13485:2003 certificates
Warranty for 2yrs
2
Revolving Stool :446
Overall all height adjustable Approx. Size: 480mm to 670mm
H
Tubular four legs base of 25.4 x 18g ERW tube.
300mm dia SS Top Height adjustment by screw mechanism.
The legs should be fitted with high quality PVC shoes with
nylon reinforcement.
All MS Parts should be 7 tanks Pre-treated & powder coated &
SS parts finished with glossy polish. Minimum 30 mm
Cushioned top with waterproof rexine cover.
Should be CE, ISI/GMP, OHSAS 18001:2007,
9001:2000,ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
ISO
3
Doctor's Table :338
Size :1200 X 750 X 750 BEECH with 2 drawer hanging unit,
Size: 400 X 400 X 300,
Table Top: Table tops made of 25mm (minimum)Prelaminated particle board of E-1 Grade Conforming to IS :
12823 of desired color with PVC edge banding. All exposed
edge sealed by 2mm (minimum)thick PVC Imported edge
Banding. Table Top Support: 18 mm thick PLB gable ends & 18
modesty Panel
Warranty for 2yrs
Should be CE, ISI/GMP, OHSAS 18001:2007,ISO 9001:2000,ISO
14001:2004 & 13485:2003 certificates.
4
Doctor's Chair :· Cushioned seat and back.
· Pneumatic height adjustable.
· Height adjustable and swinging back rest
· 5 legs chrome plated base with foot ring
Base fitted with 50 mm dia castors
Warranty for 2yrs
Should be CE, ISI/GMP, OHSAS 18001:2007,
9001:2000,ISO 14001:2004 & 13485:2003 certificates.
200
ISO
5
Visitor's Chair :400
The frame is made out of 25mm thick tube Thermo set
powder coating by epoxy polyester hybrids to a thickness of
40 – 50 microns after 7 step pre-treatment processes.
Seat: Made of 12mm thick plywood cushioned with 37mm
thick PU foam of density 32.
Back: Made of 10mm thick plywood, cushioned with 25mm
thick
PU
foam
of
density
26.
Fabric: Colour from fabric shade card
Dimensions:
Seat Width: 440mm, Seat Height: 460mm & Seat Depth:
425mm
Overall Height: 810mm & Overall Width: 550mm
Warranty for 2yrs
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,
ISO 14001:2004 & 13485:2003 certificates.
6
Bed side screen-3 Fold:1509
Overall Size : 1680mm L x 2450mm W
Tubular frame work should be made from 19mm dia x 1.2mm
ERW CRCA tubes.
Legs Base should be made from dia 25.4mm x 1.2mm tube
ERW CRCA Tubes Fitted with 50mm dia non-rusting castor.
Middle panel should be 1220mm and side panels 610mm
each side. Should have curtain hooks and wire.
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,
ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
7
Invalid Wheel Chair:281
Should be Folding type, made of mild steel tubular
construction OD 22 mm.
With fixed arm rest and fixed aluminum foot rests with folding
action.
Seat and back rest should be of superior quality leatherite.
Two rear solid rubber typed bicycle wheel, dia 24 inch with
Self propelling hoops fitted with hand brakes. Two front
swivel castor of 200mm chrome-plated finish.
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,
ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
8
Stretcher-on-trolley:274
Made of SS 304 grade SS pipes. Overall approx size: 2130mm L
x 560mm W x 810mm H. Frame work should be made of ERW
CRCA tubes welded with vertical upright of 31.75 mm OD x
18G ERW tubes, reinforced at bottom with 35mm OD x 18G
for fitting 150mm dia swivels castors wheels, all without
brake. All horizontal stays should be made of 25.4mm OD x
18G tube. Stretcher made of 20 G sheet dished in the middle
& supported horizontally on 25.4mm OD x 18G tubes. Three
additional 25 x 5mm flat supports welded to support MS
sheet top from underneath widthwise. Pushing handle at both
ends shall be made of 25.4 mm x 18G SS tube. Four stump
legs of 25.4mm x 14G ERW tube should be welded at the
bottom of the stretcher frame. Should be fitted with PVC or
synthetic material having Nylon reinforced. All MS parts
should be 7 tank pre-treated & Powder Coated.
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO
9001:2000,ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
9
Patient Waiting Chair :281
Waiting area chairs
-Option for 2 or 3 seater
Ergonomically designed seat/back
Twin tube designer under structure
Waterfall seat edge
With/ without arms
Dimensions Width Depth Height Seat height
3 Seater
152
46
85
46
Should be CE, ISI/GMP,OHSAS 18001:2007,ISO 9001:2000,ISO
14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
10
Dispensing Table :216
MS Frame with SS top. 180 X 60 X 46 cm, Epoxy powder
coated
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,
ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
11
Medicine Rack :Should be made of heavy MS Sheet all three sides
Heavy front door frame with glass/polycarbonate panel
Glass shelves removable. Door with lock & key
White Spray Painted
Should be CE, ISI/GMP, OHSAS 18001:2007,
9001:2000,ISO 14001:2004 & 13485:2003 certificates.
12
299
ISO
Warranty for 2yrs
Almirah for Medicines :566
Spray Painted
Should be made of heavy MS Sheet all three sides as well as
front door.
Shelves removable. Door with lock & key
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO
9001:2000,ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
13
Office Table :200
Size :1200 X 600 X 750 BEECH with 2 drawer hanging unit
Size: 400 X 400 X 300
Table Top: Table tops should be made of 25mm (minimum)
Pre-laminated particle board of E-1 Grade of desired color
with PVC edge banding. All exposed edge should be sealed by
2mm (minimum) thick PVC Imported edge Banding.
Table Top Support: 18 mm thick PLB gable ends & 18 modesty
Panel
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,
ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
14
Office Chair :285
Nylon base with glass filled Nylon castors gas lift with 100mm
travel. Synchronic Tilt Mechanism with Single Position Lock
Should be Thermo set powder coating by epoxy polyester
hybrids.
Seat should be made out of 4mm & 15mm molded hot
pressed plywood cushioned with high-density pre-molded
foam of 55 – 60 density. Back is to be made out of mesh back
fabric.
Arms – High density height adjustable cushioned
polyurethane – padded arms.
Dimensions:
Chair Height – 900mm to 1000mm, Chair Width – 600mm
(Center arm to arm), Seat Height 400mm to 500mm, Arm
Height 190mm to 290mm & Seat Depth 550mm
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,
ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
15
Hydraulic OT Table :
285
Five Section Stainless steel top S.S. covered base with autolocking Device,
Complete with all standard Accessories including water proof
mattress.
Overall size: 72” x 20” x 32”
Height:- Fixed.
Range of positions:- Straight, trendelenburg & reverse
tredlenburg, chair, lithotomy positions.
Should be CE ,ISI/GMP,OHSAS 18001:2007,ISO 9001:2000,ISO
14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
16
Instrument Cabinet. :244
Compact cabinet should be made of 3 sides close MS Sheet
having polycarbonate door panel in the front.
Five adjustable 6.0mm polycarbonate shelves & front lockable
door with 4mm polycarbonate panel
Pre-treated and oven baked finish
Size : (H) 63” x (B) 24” X (D) 18”
Should be CE, ISI/GMP,OHSAS 18001:2007,ISO 9001:2000,ISO
14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
17
18
IV Stand:407
Made of304 Grade SS pipes,
Moulded five-spiked base on 50 mm castors,
304 Grade SS adjustable rod with double hook.
Manufacturer should be ISO 9001:2008 & 13485 certified and must
have CE, SSI Certificate and must be registered with Registrar of
Firms
Warranty for 2yrs
Dressing Trolley:230
Should be made from SS 16SWG pipes having two SS Machine
pressed dipped tops provided with four-side side railing,
holder cage for bowl and bucket, SS bowl and bucket, push
handle, on 10cms castors.
Dimension: 76 L x 46 W x 81 H cms.
Manufacturer should be ISO 9001:2008 & 13485 certified
and must have CE, SSI Certificate and must be registered with
Registrar of Firms.
Warranty for 2yrs
19
Hospital Bed with Mattress :2439
Frame should be made of rectangular 16 G CRCA pipes, 18 G
CRCA perforated sheet top, SS head and foot bows should be
fitted with laminated wooden boards, provided with mattress
guard, provision for fixing IV/Saline rod, pre-treated in 7 Tank
hot processes and powder coated. Dimension: 203 L x 90 W x
60 H cms. 4" Supplied with Foam Mattress covered with water
proof rexine.
Specifications of mattress:- (uni to dme).
Single section Mattress with 4” thick PU Foam of 32 densities
covered with PVC Rexine.
Mattress of the bed is made up of foam with anti-microbial
agent incorporated into all components for prohibiting
growth of bacteria and fungi.
Sealed stitches and water proof zip.
Standard Accessories:
Mosquito net poles set.
Warranty: 02 years
Manufacturer should be ISO 9001:2008 & 13485 certified and
must have CE, SSI Certificate and must be registered with
Registrar of Firms
Warranty for 2yrs
20
ICU Bed. :300
Frame made of 16 G CRCA rectangular pipes, 18G CRCA sheet
four section perforated top with back-rest, knee-rest,
Trendelen-burg's and reverse Trendelen-burg's position, Hi-Lo
(high-low) height adjustable (positions maneuverable by four
separate screw mechanisms) imported ABS panels/head and
leg bows,Aluminium Collapsible Side Rails, provided with one
number IV/saline rod with provision for fixing IV/saline rod at
four corners of the bed frame, 15 cms diameter swiveling
castors which two with brakes. The bed is pre-treated in 7
tank hot process and powder coated. Dimension 203L x 90Wx
60-80 H Cms (approx.).
Manufacturer should be ISO
9001:2008 & 13485 certified and must have CE, SSI Certificate
and must be registered with Registrar of Firms.
Warranty for 2yrs
21
Fowler Bed:450
Frame made of 16 G CRCA rectangular pipes, 18G CRCA sheet
four section perforated top with back-rest, knee-rest
maneuverable from foot-end by separate screws, imported
ABS panels/head and leg bows, provision for fixing IV/saline
rod at four corners of the bed frame, provided with mattress
guard at four locations, the rod mounted on 10 cms diameter
swiveling castors which two with brakes. The bed pre-treated
in 7 tank hot process and powder coated. Dimension: 203 L x
90 W x 60 Hcms(Approx.). . Manufacturer should be ISO
9001:2008 & 13485 certified and must have CE, SSI
Certificate and must be registered with Registrar of Firms
Warranty for 2yrs
22
23
Semi-Fowler Bed:450
Frame made of 16G CRCA rectangular pipes, 18G CRCA sheet
two section perforated top with back-rest maneuverable from
foot-end by screw, imported ABS panels/head & Foot Bows,
bed mounted on rubber stumps, provided with mattress
guard on four locations, provision for fixing IV/Saline rod. The
bed pre-treated in 7 tank hot process and powder coated.
Dimension: 203L x 90 W x 60 H cms (Approx.). Manufacturer
should be ISO 9001:2008 & 13485 certified and must have CE,
SSI Certificate and must be registered with Registrar of Firms.
Warranty for 2yrs
Bed Side Locker:2048
Approximate dimension: 16” L x 16” W x 32” H.
Should be made of 20 G MS CRCA Sheet.
Should be Joint less SS top with 3 sides raise edges.
Should have one storage cabinet and one drawer under the
top and space for keeping utilities between the drawer and
cabinet.
Legs should be fitted with 2 non-rusting castors of 50mm dia
and 2 PVC Stumps on front side.
2 Rubber / PVC Buffer should be provided at rear side of the
locker.
Pre-treated in seven Tank and Epoxy Powder Coated.
Should be CE, ISI/GMP,OHSAS 18001:2007,ISO 9001:2000,ISO
14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
24
Foot Step Double:306
Overall Approx. size: 510mm L X 300mm W x 230/450 H
First Step height should be 230mm approx.& second step size
450mm approx. step should be made of 18G CRCA sheet.
Welded on MS. Tubular frame of 25.4mm x 18G fitted with
aluminum treated flats of size: 500mm L x 32mm W x 3 mm
thick, fitted by aluminum pop rivet. The legs should be fitted
with high quality PVC shoes with nylon reinforcement. All MS
parts should be 7 tank pretreated & powder coated.
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO
9001:2000,ISO 14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
25
Mayo's Instrument Trolley. :1000
a) Overall Approx. Tray Size: 560L x 400W mm
b) Should be Adjustable height of tray Approx. 760 x
1270mm through gear handle
c) Frame work should be made of 50 x 30 x 1.22 mm
rectangular M.S. Tubes.
d) Vertical Tube should be made of 50 mm x 50 mm x
1.22mm MS Tubes.
e) Tray should be made of 0.9mm thick S.S. 304 Grade
sheet.
f) Tray frame should be made of 9mm SS Rod
g) Trolley should be mounted on 50mm dia non-rusting
castors
h) MS Parts should be pre-treated in 7 tanks and powder
coated.
i) Should be CE, ISI/GMP, OHSAS 18001:2007, ISO
9001:2000,ISO 14001:2004 & 13485:2003 certificates
Warranty for 2yrs
26
Field Type OT Table.:50
Size 72” X 27” X 30” frame made of heavy tubular steel with
Strong mechanism for height adjustment. Stainless steel top
in Sections. Detachable leg side complete with anesthetist
screen Lithotomic rods with straps & arm rest.
Should be CE, ISI/GMP, ISO 9001:2000, & 13485:2003
certificates.
Warranty for 2yrs
27
Instrument Trolley. :230
Should be made of SS 16 SWG pipes/ 20 SWG two shelves,
provided with three-side side railing on top, having four siderailing on bottom self, on 7.5cms castors. Dimension: 60L x
46W x 81H cm.
Manufacturer should be ISO 9001:2008 & 13485 certified and
must have CE, SSI Certificate and must be registered with
Registrar of Firms.
Warranty for 2yrs
Labour Table :229
j) Overall Approx. Max. Size 72” x 27” x 30”
k) Frame work should be made of 31mm x 18G and
supporting tubes made of 25mm x 18G S.S. Tube
l) Leg should be fitted with PVC Stamps.
m) 3 Section Top should be made of Bakelite sheet.
n) Back rest section should be adjustable on ratchet
mechanism.
o) Leg end section should be slide under the main section
by smooth mechanism
p) The entire table top gives trendlenburg position by
screw system.
q) Should have Height adjustable a pair of leg holders
with straps.
r) Complete with self-locking traction handle at side, SS
IV Rod and foam mattress.
s) MS Parts should be pre-treated in 7 tanks and powder
coated.
t) Should be CE,ISI/GMP,OHSAS 18001:2007,ISO
9001:2000,ISO 14001:2004 & 13485:2003 certificates.
u) Warranty for 2yrs
28
ANNEXURE XIII F
SPECIFICATIONS & DETAILS OF ITEMS
GROUP (F)
Si
No
1
Specification
Qty(No)
BPMachine(Mercurial)
First grade quality - virgin material used
Purity of mercury 99.99% due to assured triple distillation
process
0 to 300 mm of Hg scale with elegant finish, fine numbering and
durable background contrast paint for clear visibility
Fused type, permanent graduation marking on the glass tube
Special control valve for perfect pressure drop
Best quality cuff for getting excellent grip
Surface plating adapted to all exposed metal parts to prevent
corrosion
Classic Hi-stove painting to the body of the instrument to
withstand in any climate
Optimum damping effect provided for easy and fast
measurement
Should be CE & ISO Certified/ISI Marked.
688
Warranty for 2yrs
2
Weighing Machine (Adult) :Size: 30 x 23.5 x 5.5 cm
Capacity: 125 x 0.5 kg
Weight: 2.2 Kg
Smartly Styled Scale with unique sunken lens
Should have latest comfortable ‘Feet Positioning ‘design with
centre parting height weight chart.
Should be CE & ISO Certified
Required registration from the Legal Metrology, Weights &
Measures for both the manufacturer as well as dealer.
Warranty for 2yrs
688
3
Weighing Machine (Baby cum Child):Weights & Measures sealed, with separable baby tray,
Epoxy powder coated. with S.S. Pan, capacity 15kg X 50gms
Required registration from the Legal Metrology, Weights &
Measures for both the manufacturer as well as dealer.
Should be CE & ISO Certified
688
Warranty for 2yrs
4
Thermometer:Oral use with ISI mark
Yellow- state of art of thermometer
Yellow capillary/glass tubing
Range: 35ºC to 42ºC(94ºF to 108/110ºF)
1500
Packing: Blister Pack
Should be CE & ISO Certified
Warranty for 2yrs
5
Stethoscope:Combined Adult and Pediatric Aluminum anodized finished
Chest piece.
Ultra-Sensitive Diaphragm for greater amplification.
Colour coordinated Non-Chill bell and Snap On.
Ring to retain diaphragm for patient comfort.
Complete with an accessory case containing.
2 spare diaphragms and one set of ear tips.
Extra-thick tubing walls minimize extraneous noise.
Includes ID Tag.
Should be CE & ISO Certified
Three year warranty against any mfg. defect.
1500
Warranty for 2yrs
6
7
X -Ray View Box :X-Ray View Box Double Film with two tubes and epoxy powder
coated deluxe.
Should be CE & ISO Certified
Warranty for 2yrs
Autoclave IS Mark No. 8462 with dressing drums:Portable vertical sterilizer autoclave seamless made out of thick
high quality stainless steel sheet,
deep drawn to cylindrical shape, having no joints and welding,
seamless construction which shall
allow no bacteria residue and free from dirt accumulation.
Size: 350 mm diameter x 300-325 mm height.
Warranty:- 01 year
Dressing drums ISI Mark No. 3831, without any joints.
Size: 225 x 225 mm
275
240 mm
688
354
Warranty for 2yrs
Should be ISO Certified.
8
Electric Sterilizer Seamless shell, with automatic lifting handle with
tray all supplied with power cord.:Specifications:a) Electric Sterilizer – Big
–Should be IS : 5022–1989
Made of Seamless S.S. Sheet of grade-304 (18 Cr-8 Ni).
Suitable for 220V, 50 Hz, Single Phase, AC Supply.
L: 510, W: 200, H: 150mm, Power: 2.00 Kw
b) Electric Sterilizer – Medium
–Should be IS : 5022–1989
Made of Seamless S.S. Sheet of grade-304 (18 Cr-8 Ni).
297
Suitable for 220V, 50 Hz, Single Phase, AC Supply.
L: 430, W: 200, H: 150mm, Power: 1.50 Kw
c) Electric Sterilizer – Small
–Should be IS : 5022–1989
Made of Seamless S.S. Sheet of grade-304 (18 Cr-8 Ni).
Suitable for 220V, 50 Hz, Single Phase, AC Supply.
L: 400, W: 150, H: 125mm, Power: 1.00 Kw
Warranty for 2yrs
9
Oxygen Cylinder B Type with flowmeter and wrench.:The oxygen cylinder should confirming to IS : 7285 (Part 1) –
2004 and with appropriate valves confirming to IS: 3224-2002
for Medical oxygen gas service Cylinders subjected to
hydrostatic stretch test at pressure of 250 Bar as required under
rule 35 of the Gas Cylinder Rules , 2004.
10 trs water capacity. Supplied with Flow meter and wrench.
Warranty for 2yrs
Oxygen Cylinder Trolley. :Should be suitable for 10 liter gas cylinder.
MS tubular frame work should be made of approx. 25.4mm x
18G MS Round tube fitted with two rubber wheels, 100mm dia
trolley should have locking provision made of 5mm x 25mm
thick MS Flats.
Trolley should be fitted with MS Base of 16G sheet.
All MS parts should be 7 tanks pretreated & powder coated.
Should be CE, ISI/GMP, OHSAS 18001:2007, ISO 9001:2000,ISO
14001:2004 & 13485:2003 certificates.
Warranty for 2yrs
674
11
Kidney Tray SS.:Kidney Tray SS.As Per IS: 3992-1982 (Heavy Quality)
Size: 250 x 100
300 130
Warranty for 2yrs
237
12
Instrument Tray with cover SS.:Instrument Tray with cover SS Seamless IS 3993-192.The
finished thickness should not be less than 0.5 mm.
Size: 350 x 250 mm
450
300 mm
Warranty for 2yrs
400
13
Needle Destroyer-cum-Hub Cutter :1. Compact Device that fits easily on the desktop.
2. Portable, safe and cost effective system which creates
save environment for Doctors, Nurse, Pathologist, Healthcare
professionals and patients.
3. Cutter: Very high grade imported steel which does not rust
or becomes blunt even after long use.
4. Body should make up of ABS plastic which avoids rusting
and electric shock.
725
10
250
5. Electrodes should be copper electrode Nickle plate.
6. Temperature: Burningdeg.c should be 1600c.
7. Steel Grade should be SS316L which can cut syringe hub
and burn needle approx. 25000 pcs to 28000pcs and life is 2years minimum.
8. Supplied with Removable discharge tray for easy disposal
of needle ash and syringe hubs.
9. Power consumption of continuous rating in use should be
60w.
10. Shock proof ,fuse protection having, OFF & ON switch.+
Warranty for 2yrs
14
15
Bowl Stand with bowl:Five legs base mounted on 5cms dia castors.
With two approx. 35 cm SS Basin
Frame should be made of SS Pipe & SS rings.
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003
certificates
Warranty for 2yrs
Instruments for Normal and Epistomy Delivery :- Should be, ISO
9001:2000 & 13485:2003 certificates
Vaccum extractor, Maelstrom :- 1
Forceps obstetric, Wrigley’s, 280 mm, stainless steel :- 1
Forceps, obstetric, Barnes-Neville, with traction, 390mm:- 1
Forceps, sponge holding, straight 228 mm, stainless steel:- 4
Forceps, artery, Spencer-Wells, straight, 180mm-ss :- 2
Forceps, artery, Spencer-Wells, straight, 140mm-ss :- 2
Holder, needle straight, Mayo-Hegar, 175 mm-ss :- 1
Scissors, ligature, Spencer, 130 mm, stainless steel:- 1
Scissors, episiotomy, angular, Braun, 145 mm, stainless steel:- 1
Forceps, tissue, spring-type, 1 x 2 teeth, 160 mm-ss :- 1
Forceps, tissue, spring-type, serrated ups, 160mm-ss :- 1
Catheter, urethral, rubber, Foley’s 14 ER :- 1
Catheter, urethral, Nelaton, set of five (Fr 12-20) rubber:- 1
Forceps, backhaus towel -130 mm-ss :- 4
Speculum, vaginal, Sim’s, double-ended # 3-ss:- 1
Speculum, vaginal, Hamilton-Bailey :- 1
224
269
Warranty for 2yrs
16
17
Wall Clock :
Around 8 inch diameter-Round type
Having pointer for second, Analog Type.
Warranty for 2yrs
Nitrous Oxide Cylinder 5 Ltrs:Brand New High Pressure Seamless Cylinders for Nitrous Oxide
Gas, duly filled with gas, ‘A’ type.
Having water Capacity 5Litres, Cylinders should be “ISI” Marked,
Conforming to IS: 7285 Specification,
Fitted with Pin Index flush type Valve, painted as specified
under Gas Cylinders Rules 1981.
Warranty for 2yrs
1000
2000
18
Oxygen Cylinder A Type:Brand New High Pressure Seamless Cylinders for Oxygen Gas,
duly filled with gas ‘A’ type.
Having water Capacity 5Litres, Cylinders should be “ISI” Marked,
Conforming to IS: 7285 Specification,
Fitted with Pin Index flush type Valve, painted as specified
under gas cylinders rules 1981.
Warranty for 2yrs
2000
19
Instrument for C-Section and other operations.:Should be CE, ISO 9001:2000, & 13485:2003 certificates
a) Delivery Kit
Trolley, dressing carriage size 76C, long x 46 cm wide and 84 cm
high.
Ref. IS 4769/1968 1 1Pc.
Towel, trolley 84 cm x 54 cm 2Pc
Gown, operation, cotton 1Pc
Cap. Operation, surgeon’s 36 x 46 cm 2 2Pc
Gauze absorbent non-sterile 200 mm x 6 m as per IS: 171/1985
2Pc
Tray instrument with cover 450 mm (L) x 300 mm (W) x 80 mm
(H) 1 Pc
Macintosh, operation, plastic - 2Pc.
Mask, face, surgeon’s cap of rear ties: B) Beret type with elastic
hem 2pcs ,
Towel, 2 pcs
gloves 3 Pairs
Cotton wool absorbent non-sterilize 500G 2Pc
Drum, sterilizing cylindrical – 275 mm Dia x 132 mm, ss as per
IS: 3831/1979 2Pc
Table instrument adjustable type with tray ss 1Pc.
107
b) Episiotomy kit
Vacuum extractor, Malastrom 1 1
Forceps obstetric, Wrigley’s, 280 mm, stainless steel 1
Forceps, obstetric, Barnes-Neville, with traction, 390mm 1
Forceps, sponge holding, straight 228 mm, stainless steel 4
Forceps, artery, Spencer-Wells, straight, 180mm-ss 2
Forceps, artery, Spencer-Wells, straight, 140mm-ss 2
Holder, needle straight, Mayo-Hegar, 175 mm-ss 1
Scissors, ligature, Spencer, 130 mm, stainless steel 1
Scissors, episiotomy, angular, Braun, 145 mm, stainless steel 1
Forceps, tissue, spring-type, 1 x 2 teeth, 160 mm-ss 1
Forceps, tissue, spring-type, serrated ups, 160mm-ss 1
Catheter, urethral, rubber, Foley’s 14 ER 1
Catheter, urethral, Nelaton, set of five (Fr 12-20) rubber 1
Forceps, backhaus towel -130 mm-ss 4
Speculum, vaginal, Sim’s, double-ended # 3-ss 1
Speculum, vaginal, Hamilton-Bailey 1
c) Forceps Delivery Kit
Forceps, obstetric, Neville-Barnes, W/traction 390 mm 1
Hook, decapitation, Braun, 300 mm, stainless steel 1
Hook, crochet, obstetric 300 mm, Smellie, stainless steel 1
Bone, forceps, Mesnard 280 mm, stainless steel 4
Perforator, Smellie, 250 mm, stainless steel 1
Forceps, cranial, Gouss, straight, 295 mm-ss 1
Cranioclast, Braun, stainless steel, 365 mm long 1
Scissors ligature Spencer 130 mm, stainless steel 1
Forceps sponge holding, 22.5 cm straight – ss 1
Forceps, tissue, spring-type, 1 x 2 teeth, 160 mm, stainless steel
1
Forceps, tissue, spring-type, serrated tips, 160 mm-ss 1
Forceps, artery, Spencer–Wells, straight, 180 mm-ss 2
Forceps, artery, Spencer-Wells, straight, 140 mm-ss 2
Forceps, scalp flap, Willet’s 190 mm –ss 4
Forceps, Vulsellum, duplay double curved, 280 mm-ss 4
Forceps, Vulsellum, duplay double curved, 240 mm-ss 1
Catheter, urethral, 14 Fr. Solid tip, one eye, soft rubber 3
47 Holder, needle, Mayo-Hegar, narrow jaw, straight, 175 mmss 1
Speculum vaginal bi-valve, Cusco-medium, stainless steel 1
Speculum, vaginal sim’s double-ended, size # 3-ss 1
Forceps, Backhaustowel, 130 mm, stainless steel
Warranty for 2yrs
20
Micropipettes:Single
Channel
a. 10µl – 100 µl
b. 100 µl - 1000 µl
c. 5 µl – 50 µl
234
Variable
volume
Micro
pipettes
8 Channel Micropipette
a. 10 µl – 100/200 µl
b. 100 µl – 300 µl
Warranty for 2yrs
21
Neonatal Resuscitation Kit :Infant Resuscitator with 250 ml Silicone Bellow, pressure release
valve
Silicone Face Mask (Anatomical): Autoclavable & reusable in
sizes 00, 01
Foot Suction: Compact, lightweight, easy to handle and operate,
Durable rubber bellow,
Long lasting stainless spring to provide friction free pumping
Completely Autoclavable polycarbonate vacuum jar with lid
(500ml capacity), Scratch
Proof power coated frame
Laryngoscope: Stainless Steel Straight blades of Size 0& 1 No.
Silicone airways: Autoclavable and reusable in Size 000& 00 No.
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003 certificates
Warranty for 2yrs
50
22
Vacuum Extractor:
50
Should consist of 03 stainless steel/plastic (autoclavable) cups,
rubber pressure tube, suction pump, traction handle, glass jar
fitted
with
vacuum
gauge
and
control
valve.
Should be supplied completely in a carrying case.
Should be CE ,ISI/GMP, ISO 9001:2000 & 13485:2003 certificates
Warranty for 2yrs
23
Oxygen Cylinder A Type with Humidifier:Brand New High Pressure Seamless Cylinders for Oxygen Gas,
duly filled with gas ‘A’ type.
Having water Capacity 5Litres, Cylinders should be “ISI” Marked,
Conforming to IS: 7285 Specification,
Fitted with Pin Index flush type Valve, painted as specified
under gas cylinders rules 1981 with humidifier
Warranty for 2yrs
ANNEXURE-XIV
Form of Agreement
1000
THIS CONTRACT AGREEMENT is made
This ……………. day of month……………………….. year…………………….
BETWEEN
(1) Name and Address of the Purchaser:
(2) Name and Address of the Supplier:
WHEREAS the Purchaser invited bids for certain goods and ancillary services, viz., [insert:
brief description of goods and services] and has accepted a bid by the Supplier for the
supply of those goods and services in the sum of [insert: contract price in words and figures]
(hereinafter called “the Contract Price”)
NOW THIS AGREEMENT WITNESSETH AS FOLLOWS:
1. In this Agreement words and expressions shall have the same meaning as are
respectively assigned to them in the Condition of Contract referred to.
2. The following documents shall constitute the Contract between the Purchaser and
the Supplier, and each shall be read and constructed as an integral part of the
Contract:
(a) This Contract Agreement
(b) Special Conditions of Contract
(c) General Conditions of Contract
(d) Technical Requirements ( including Technical Specifications)
(e) The Supplier’s bid and original Price Schedules
(f) The Purchaser’s Notification of Award
(g) [Add here: any other documents]
3. In consideration of the payments to be made by the Purchaser to the Supplier as
hereinafter mentioned, the Supplier hereby covenants with the Purchaser to provide
the Goods and Services and to remedy defects therein in conformity in all respects
with the provisions of the Contract.
4. The Purchaser hereby covenants to pay the Supplier in consideration of the provision
of the Goods and Services and the remedying of defects therein, the Contract price
or such other sum as may become payable under the provisions of the Contract at
the times and in the manner prescribed by the Contract.
For and on behalf of the Purchaser
Signed: ____________________________________________________
In the capacity of [insert: title or other appropriate designation]
In the presence of _____________________________________________
For and on behalf of the supplier
Signed: _____________________________________________________
In the capacity of [insert: title or other appropriate designation]
In the presence of _____________________________________________
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising