User Manual

User Manual
MK233A Overcurrent Relay User's Guide
start/
start/
/delay time
1. DESCRIPTION
The MK233A is microprocessor based numerical overcurrent relay. It uses fundamental
frequency current measurement for excellent harmonic current rejection. The relay
consists of independent low-set and high-set elements. The high-set element can be
disabled by the user. The time current characteristics of the low set element are definite
time or five selectable IDMT curves. The high-set element is a definite time or
instantaneous relay. The 4-digit panel display on the MK233A allows the display of the
present load current; recorded fault current for last tripping; and all settings of the relay.
2. LIGHT INDICATORS
The indicators display the status of the system as follow:
Indicator
Aux
0
1
1
1
1
1
1
l> l>> FUNC DT
Status
0 0
0
0 No Auxiliary power supply.
0 0
X
X Normal condition, no tripping.
1 0
X
X Low-set overcurrent triggered,
time delay countdown started.
0 1
X
X High-set overcurrent triggered,
time delay countdown started.
B 0
B
B Low-set tripped,
FUNC LED indicates tripping source,
DT LEDs show tripped value.
0 B
B
B High-set tripped,
FUNC LED indicates tripping source,
DT LEDs show tripped value.
X X
B
1 Programming mode.
Table 1: System Status
1 = ON
0 = OFF
X= don’t care, not blinking
B = blinking DT = DATA FUNC = FUNCTION
Indicator
FUNCTION
. 1
2
3
1
2
3
4
5
6
7
8
DP
off
off
off
blink
blink
blink
off
off
off
off
off
DATA
L1 load current.
L2 load current.
L3 load current.
L1 previous tripped current.
L2 previous tripped current.
L3 previous tripped current.
Low-set current setting.
Time multiplier /delay time setting.
High-set current setting.
High-set delay time setting.
Soft switch setting.
Table 2: FUNCTION Code
Note:
Step 1: Press RESET key until the function digit
shows required function.
Step 2: Press the UP and
simultaneously to enter
mode. The function digit
indicates the relay is in
Step 3: Use the UP or DOWN key to select the
desired value.
Step 4: To save the selected value, press the
UP and DOWN key simultaneously again.
It will exit the programming mode with the
data digits displaying new setting.
To exit programming mode without saving the
selected setting, press the RESET key once.
4. OUTPUT CONTACTS
The MK233A has two set of output contact:
(i) CONTACT R1 - linked to trip signal.
(i) CONTACT R2 - linked to trip or start signal.
The output contact can be programmed to be either
auto reset type or manual reset type.
For auto reset type, the contact remain activated until
the fault current is removed.
For manual reset type, the contact remain activated
even with the removal of fault current.
5. SOFT SWITCHES
The MK233A incorporates 4 soft switches for system
configuration. When the function digit shows “8”, the
relay is in soft switch setting mode.
Under normal operating condition, The 4-digit display
is off. When the RESET key is pressed, the 4-digit
display will light up. The display will switch off
automatically after 6 minutes if no further key is
pressed.
3. PUSH-BUTTONS OPERATION
a) Trip test
Press the “TEST” button to simulate a trip condition.
b) Trip reset
Press the “RESET” button to reset the relay when
tripped.
c) View setting
When the relay is not under tripped condition,
pressing the “RESET” button will scroll through
the various functions.
“ ”
switch value (SVL)
switch number (SW)
SW SVL
1
System configuration
00 Contact R1 linked to trip signal auto reset type.
01 Contact R1 linked to trip signal manual reset type.
2
00 Contact R2 linked to trip signal auto reset type.
01 Contact R2 linked to trip signal manual reset type.
10 Contact R2 linked to signal auto reset type.
11 Contact R2 linked to signal manual reset type.
3
00 Low-set normal inverse curve 3/10.
01 Low-set normal inverse curve 1.3/10.
02 Low-set long time inverse curve.
03 Low-set very inverse curve.
04 Low-set extremely inverse curve.
Figure 1: Scroll sequence
d) Program setting
Only function codes from 4 to 8 can be programmed.
DOWN key
programming
will blinks to
programming
05 Low-set definite time.
4
00 High-set disabled.
01 High-set enabled.
Table 3: Soft switch setting
Figure 4:IDMT Long time Inverse Curve
Figure 2: IDMT Normal Inverse Curve 3/10
Figure 6:IDMT Extremely Inverse Curve
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.05
Figure 5:IDMT Very Inverse Curve
Figure 5:IDMT Normal Inverse Curve 1.3/10
6. TECHNICAL DATA
Ratings
Rated current In ......................5 A
Frequency ...............................50 Hz or 60 Hz
Burden ....................................< 0.3 VA at In
Auxiliary Supply
MK233A-240A(6).....................198~265 VAC
MK233A-110A(6).....................94~127 VAC
Supply frequency ....................50 Hz or 60 Hz
VA rating .................................3 VA typical
Indicators
Auxiliary supply .....................Green LED indicator
Pick up ..................................Red LED indicator
Trip ........................................7 segment LED and
red LED indicators
Mechanical
Mounting ..............................Panel mounting
Front panel ...........................Standard DIN 96x96 mm
Approximate weight ..............0.7 kg
Setting Ranges
Low-set setting I>.....................0.5 - 6.00 A (10%-120%)
Time multiplier kt> ...................0.05- 1.00
7. CONNECTION DIAGRAMS
Low-set definite time t> ...........0.05- 99 sec
a) Overcurrent Relay
High-set setting I>> .................0.50 - 99.9 A (10%-1998%)
High-set definite time t>>.........0.05 - 2.5sec
MK 233A
Outputs
Trip Contact:
Rated voltage .......................250 VAC
Continuous carry ..................5A (cos ϕ = 1.0)
Make and carry for 0.2 s ......30A
Contact specification
Expected electrical life ..........105 operations
Expected mechanical life ......5 x106 operations
R2
R1
L1
L2
L3
N
MK 232A
MK 233A
8. CASE DIMENSION
9 6 mm
9 6 mm
Fr o n t
R1
R2
110mm
100mm
R2
90mm
90mm
R1
Figure 7: Case Dimension
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement