"user manual"

"user manual"
USER MANUAL
ENGLISH
Monochannel
telephone dialer
Monochannel telephone dialer - User manual
Index
Chapter 1
Introduction
4
1.1 Description of the telephone dialer ...................................................................................4
1.2 Operating features ............................................................................................................5
1.3 Technical specifications ....................................................................................................5
Chapter 2
Installation
7
2.1 General instructions..........................................................................................................7
2.2 Terminal board description................................................................................................8
2.3 Connections......................................................................................................................9
Chapter 3
Programming
10
3.1 Programming ..................................................................................................................10
3.1.1 Telephone numbers introduction........................................................................12
3.1.2 Message recording ............................................................................................14
3.1.3 Pulse/DTMF setting ...........................................................................................15
3.1.4 Test ....................................................................................................................17
2
Index
Chapter 4
Operating
18
4.1 Panel description ............................................................................................................18
4.2 Telephone dialer enabling...............................................................................................19
4.3 Telephone numbers visualization....................................................................................20
4.4 Telephone numbers changing.........................................................................................21
4.5 Telephone numbers cancelling .......................................................................................22
4.6 Message listening ...........................................................................................................23
4.7 Callings cycle repeating..................................................................................................24
4.8 Message repeating .........................................................................................................25
4.9 Dialer state visualization during the callings phase ........................................................26
4.10 Programming code changing..........................................................................................27
Chapter 5
Maintenance
28
5.1 Cleaning..........................................................................................................................28
5.2 Default values setting in factory......................................................................................28
3
Monochannel telephone dialer - User manual
1
Introduction
Dear customer,
we desire thank you for buying a CIA. product. We recommend you to read this manual with attention,
because it will be very useful during the installation and use phase.
As CIA customer, you can make use of a series of services, such as the technical telephone
assistance on CIA products.
1.1
Description of the telephone dialer
This device satisfy the users needing a system that, in case of alarm, calls them on a portable
telephone, or at the office, or wherever a telephone is present.
The monochannel telephone dialer allows to send, by the traditional telephone line, a vocal message
of 24 seconds at the most toward 10 different users.
The activation is made by a positive tension pulse 13V from a burglary system or, for tele-help
service, from a remote control.
4
Introduction
1.2
!
!
!
!
!
!
!
!
!
!
!
!
Operating features
Numeric display.
10 telephone numbers storing.
Max capacity up to 24 digit for each telephone number.
Possible insertion of pauses during the telephone number.
Built-in microphone for vocal message digital recording.
Maintenance of the stored message without power supply.
Loudspeaker for listening the recorded message and for test function monitoring.
Message duration up to 20 sec.
Decadical (Pulse) or multifrequency (DTMF) dialling selection.
Personal code for acces to the programming / test functions.
Test function for message sent to a single stored telephone number.
Telephone line protected by transient absorption zener.
5
Monochannel telephone dialer - User manual
1.3
Technical specifications
!
!
!
!
!
Operating voltage:
Absorption in st/by:
Absorption during alarm:
Absorption during programming:
Weight:
!
Dimensions:
6
13V! ± 5%
45mA
70mA
130mA
635g (CT81)
423g (TD81)
463g (TM81P)
180x115x34mm (CT81)
178x115x38mm (TD81)
285x95x17mm (TM81P)
Installation
DECLARATION
OF CONFORMITY’
PRODUCER: HiLTRON S.r.l.
ADDRESS: Circ. Est. di Napoli compls. Lemar 80026 Casoria (NA) - Italy
PRODUCT: MONOCHANNEL TELEPHONE DIALER
PRODUCT CODE: CT81, TD81, TM81P
THE DESCRIBED PRODUCTS ARE MADE ACCORDING TO THE REQUISITES OF THE FOLLOWING STANDARDS:
APPLYED STANDARD
TITLE
EN50081-1
EMISSION GENERIC STANDARD
Class of the generic standard: home, commercial and light industrial
EN50082-1
IMMUNITY GENERIC STANDARD
Class of the generic standard: home, commercial and light industrial
CONFORMITY WAS VALUED ON TESTS MADE ON SAMPLE AND WITH ORIGINAL SETUP OF THE DEVICES FUNCTIONAL
CONFIGURATION OPERATING, THEREFORE THE PRODUCT SATISFY THE REQUISITES OF THE 89/336/CEE DIRECTIVE.
DATE
4 Marzo 1999
GENERAL MANAGER
7
Monochannel telephone dialer - User manual
2
Installation
2.1
General instructions
!
!
!
!
!
!
8
No installing the telephone dialer exposed to the bad weather or to the extreme temperatures.
For a strong and safe fixing, it needs making sure the wall surface is plane.
Fix the telephone dialer at a height that allows an easy access to the frontal panel.
The telephone dialer is protected by tampering, but the installation in a safe place is an additional
protection.
The telephone dialer must be connected with a burglary system according to CEI 79-3 "Special
Standards for the burglary, anti intrusion and anti aggression systems”.
The telephone dialer panel TM81P has to be installed in the upper side of a TM2, TM3 or TM4 box by
the two screws in endowment. It is also possible to install the telephone dialer panel togheter with a
burglary centrale unit panel. In that case is necessary to use the TM4C box.
Installation
2.2
Terminal board description
1 2 3 4 5
1
2-3
4-5
6
7
8-9
10 - 11
GND
LINE
PHONE
Input ON
Input A
13Vcc
TAMPER
6 7 8 9 10 11
Ground connection.
Main telephone line input.
Telephone line output to connect to the phones.
Enabling of the telephone dialer by positive 13V!.
Activation of the telephone dialer by positive pulse 13V!.
Power supply 13V! +/-5%: (9)=NEGATIVE (10)=POSITIVE
Protection tamper (to connect in series to the 24h line of the burglary system).
9
Monochannel telephone dialer - User manual
2.3
Connections diagram
TD82
Main
telephone
line
BURGLARY CENTRAL UNIT
In series to the 24h line
of the burglary system
10
Programming
3 Programming
3.1
Programming phases
To enter the programming, it needs dialing the access code 1-2-3-4” setted in factory, or
pressing the RESET key inside of the telephone dialer. The display indicates the main menù.
It is possible to enter the different programming phases pressing a number from 0 to 9
(ATTENTION: the programming phase ends after one minute of inactivity).
2
3
4
- Enabling / numbers changing
It allows the telephone numbers introduction - changing - visualization cancelling
- Message recording
It allows the two vocal messages recording
- Message listening
It allows to listen again the two recorded vocal messages.
- Cycles repeating
It allows to set the number of callings cycles in case of alarm
(default = 2).
11
Monochannel telephone dialer - User manual
5
6
7
8
9
0
- Pulse/DTMF
It allows to set the decadic (Pulse) or multifrequency (DTMF) numbers dialing
selection.
- Default values restoring
It allows to reset the original factory values.
- Message repeating
It allows to set the number of times that the vocal message must be repeated for
each call. (default = 2).
- Numbers dialling selection visualization
It allows to enable or disable the telephone number dialling visualization during
the calling cycles. (default = 1”enabled”).
- Code changing
It allows to personalize the access code to the programming phases.
- TEST
It allows to make a TEST by the dialing of one of the stored telephone number
and the vocal message playback.
The phases 1,2 and 5 are necessary to enable the dialer
12
Programming
3.1.1
Code
Telephone numbers introduction
Digit the programming code, then press the “1” key.
1.
Is visualized “1” corresponding with the 1st of 10 numbers.
The point in the corner on the right of the display indicates:
Blinking: empty position (no stored number).
Fix: full position (stored number).
2
2.
Press a number from "1" to “0”.
3
3.
Press "INVIO".
(If in the choosed position there is already a telephone number
stored, it will be displayed immediately. So it needs pressing
“INVIO” again during the number visualization to change it).
1
4
5
6
7
4.
Digit the telephone number.
8
5.
Press "INVIO".
9
0
1 ÷ 0
INV
Digit the telephone
number
INV
13
Monochannel telephone dialer - User manual
Code
Repeat from the point 2 to introduce the others telephone numbers.
After introducing all the telephone numbers, (they can be also less than
10) press "PAUSA/ABB" one time to exit from the numbers introduction
phase, or two times to exit from the programming.
PA
1
2
3
4
5
6
7
8
9
0
14
PA
NOTE:
It is possible to exit from the current phase in each moment pressing
Programming
3.1.2
Code
1
2
3
4
5
6
7
Message recording
Digit the programming code, then press the “2” key.
1.
Press"1" to record the message.
2.
Press "INVIO"at the end of the message recording. Each message
can last 24 seconds at the most, after which the telephone dialer
disables automatically.
When the recording phase is ended the dialer repeats the recorded
message automatically and it returns to the point 1.
If the operation is repeated, the new message takes the place of
that previous.
Press "PAUSA/ABB" one time to exit from the numbers recording
phase, or two times to exit from the programming.
1
INV
PA
PA
8
9
0
15
Monochannel telephone dialer - User manual
3.1.3
Code
1
2
3
4
5
6
7
8
9
0
16
Pulse/DTMF setting
Digit the programming code, then press the “5” key.
1.
Is visualized “0” or “1”.
Press 0 to enable the decadic composition (Pulse), or press “1” to
enable the multifrequency composition.
After setting the kind of composition, the telephone dialer returns to
the principal menù automatically; then press "PAUSA/ABB" one time to
exit from the programming.
0
1
PA
Programming
3.2
Code
Alarm test
Digit the programming code; then press the “0” key.
1. Digit the choosed telephone number from “1” to “0” for the TEST (on
the telephone line). It is advisable to call to a cellular telephone.
1
2
3
4
5
6
7
8
2.
INV
Press "INVIO”.
The display visualizes all the calling phases, it sends the message
and it sets in stato di STAND/BY ( indicated by a fix down the display).
!
!
!
!
!
÷
Composition
of numbers
Connection with the telephone line (L.)
Telephone number dialing for the test enabled
Waiting
Message sending
End of connection
9
0
17
Monochannel telephone dialer - User manual
4
Operating
4.1
Panel description
2
3
MIC
4
Digitare il codice di programmazione
per accedere alle seguenti opzioni:
1.Inserimento / variazione numeri
2.Registrazione messaggio
3.Riproduzione messaggio
4.Ripetizione cicli
7.Ripetizione messaggio
8.Visual. invio numeri
9.Variazione codice
0.Test
1
5
1.
2.
3.
4.
5.
18
Loud-speaker for listening recorded messages and for the visualization during test phase.
Included microphone for the messages recording
Numerical display
Twelve keys pad
RESET key
Operating
4.2
Dealer enabling
To enable the telephone dialer, it needs setting a positive 13Vcc to the clamp ON (6) that
allows the dialer enabling, after setting a tension of 13Vcc to the clamp, "A" (7), the dialer starts
the calling phases to the stored numbers from 1 to 0 (see 3.1.1)
After the enabling, the telephone dialer will make the following phases
1.
Connection with the telephone line
2.
telephone numbers dialing
3.
Waiting
4.
Message sending
5.
End of connection
19
Monochannel telephone dialer - User manual
4.3
Code
1
2
3
Telephone numbers visualization
Digit the programming code, then press the “1” key.
1.
Press a number from "1" to “0” corresponding to the telephone
number to visualize.
2.
Press "INVIO” to visualize the telephone number.
3.
Press "PAUSA/ABB" one time to exit from the visualizing phase, or
two times to exit the programming phase.
4
5
6
7
8
9
0
20
1
÷
INV
Visualization
storing
number
PA
N.B. Successively the scheme on the left of each paragraph, will indicate
to dial the programming code and then to press the number (in
black) to start the choice phase.
0
PA
Operating
4.4
Code
1
2
1.
Is visualized “1” corresponding with the 1st of 10 numbers.
The point in the corner on the right of the display indicates:
Blinking: empty position (no stored number).
Fix: full position (stored number).
Press a number from "1" to “0” corresponding to the telephone
number to vary.
3.
INV
Press "INVIO".
The telephone number will be immediately displayed. It needs
pressing “INVIO” again during the telephone number visualization
to overwrite it.
6
4.
Digit the telephone number.
9
5.
Press "INVIO".
0
6.
Press "PAUSA/ABB” two times for exit.
8
0
INV
INV
2.
5
7
÷
Digit the programming code, then press the “1” key.
3
4
1
Telephone numbers variation
Visualization
storing
number
INV
Digit
new
number
( during the
visualiz.)
PA
PA
21
Monochannel telephone dialer - User manual
4.5
Code
1
2
3
4
5
Telephone numbers cancelling
Digit the programming code, then press the “1” key.
1.
Press the corresponding key to the number to cancel.
2.
Press "INVIO".
3.
Press "INVIO" to cancel.
Press "PAUSA/ABB" one time to return to the point “1”, or two times to
exit from the cancelling phase.
1
÷
INV
INV
PA
6
7
8
9
0
22
PA
0
Operating
4.6
Code
1
2
3
4
5
Message listening
Digit the programming code, then press the “3” key.
1.
Press “1” to listen the recorded message.
After listening the message press “PAUSA/ABB" one time to exit
from the listening phase, or two times to exit from the programming.
1
Reprod.
mess.
PA
6
7
8
PA
9
0
23
Monochannel telephone dialer - User manual
4.7
Code
1
2
3
4
5
6
7
8
9
0
24
Calling cycle repeating
Digit the programming code, then press the “4” key.
1.
The display visualizes the number of times the calling phase must
be repeated (default=2).
2.
Digit a number from 1 to 9 to change it.
After setting the number of times the calling phase must be
repeated in case of alarm, the dialer returns to the principal menù
automatically, then press "PAUSA/ABB" one time to exit from the
programming.
1
÷
PA
9
Operating
4.8
Code
1
2
3
4
Message repeating
Digit the programming code, then press the “7” key.
1.
The display visualizes the number of times the message must be
repeated for each call (default=2).
2.
Digit a number from 1to 9 to change it.
After setting the number of times the message must be repeated,
the dialer returns to the principal menù automatically; then press
"PAUSA/ABB" to exit from the programming.
1
÷
9
PA
5
6
7
8
9
0
25
Monochannel telephone dialer - User manual
4.9
Code
1
2
3
4
5
6
7
8
9
0
26
Dialling visualization during the callings
Digit the programming code, then press the “8” key.
1.
Press “1” to enable the dialer state visualization during the callings
phases, or press “0” to disable it.
The dialer returns to the principal menù automatically, then
press"PAUSA/ABB" one time to exit from the programming.
0
1
Disab.
Abilitato
PA
Operating
4.10
Code
Programming code changing
Digit the programming code, then press the “9” key.
1.
Digit the new code (4 digits).
2.
Press "PAUSA/ABB" two times.
Digit
new
code
1
2
3
PA
4
5
6
7
8
9
0
27
Maintenance
5
Maintenance
5.1
Cleaning
!
!
5.2
Code
For the panel cleaning, use only a soft and humid cloth.
No using absolutely diluents and abrasive sponges.
Default values settings in factory
Digit the programming code, then press the "6” key.
1.
Press the “8” key.
2.
Press the “2” key.
6
8
2
PA
28
260DE-1.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement