USER MANUAL
LED BEAM MOVING HEAD 108
Professional Entertainment Technology
www.flash-butrym.pl Strona 1
TABLE OF CONTENTS
1.
Safety Instruction
2. Technical Specification
3.
How To Set The Unit
4.
How To Control The Unit
5. Troubleshooting
6. Fixture Cleaning
Please read carefully the instruction, which includes important information about the installation. usage and maintenance
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user.be sure that they also receive this instruction booklet
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
The unit is for indoor use only. Use only in a dry location
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked
Disconnect main power before replacement or servicing.
Make sure there is no flammable materials close to the unit while operating as it is fire hazard.
Use safety cable when fixes this unit. Don’t handle the unit by taking its head only,
But always by taking its base.
Maximum ambient temperature is ta:40°C. Don't operate it where the temperature is higher than this. www.flash-butrym.pl Strona 2
Unit surface temperature may reach up to 85°C .Dont touch the housing bare-hand during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving.
In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type Spare parts.
Warning
To prevent or reduce the risk of electrical shock or fire, do not expose the unit the rain or moisture.
Do not open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. ln the unlikely event your unit may require service,
Please contact your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping white operating. And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.
Fixture Cleaning
The cleaning of internal and external optical lens and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the units optics
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days www.flash-butrym.pl Strona 3
Another new edition of Led Moving Head 108 x 3W RGBW well-know has Strong, but this time it came with CREE LED's and it very attractive light.
And it have 108 high-quality LED Red, Green, Blue, White, that make it to provides a very good light and bright, in which make it have a strong and very concentrated light beam.
The view Angle 5°, and You also get a complete additional filter that will turn wider the wash angle to 25°.
FEATURES
High quality CREE LED's in four basic colors (RGBW)
Angle 5°- 25° additional filter
color Balance
Extremely fast and very good precise movement
Ultra compact design light
The device weight (8.4 kg)
PHYSICAL
Height: 390 mm
Width: 370 mm
Depth: 265 mm
Weight: 8.4 kg
DYNAMIC EFFECTS
RGBW color mixing
Liquid electronic dimmer (0-100 %)
Electronic strobe with variable speed (0 - 20hz ), or the result of random
PAN : 630o
TILT : 240o
Speed control PAN , TILT DMX
CONTROL AND PROGRAMMING
Control of the market definition PAN and TILT ( 8bit or 16bit )
DMX512 : 9, 12 or 16 channels
Sound control , master-slave
Setting and addressing : LCD with back-light
OPTICS
Viewing angle : 5 °
Light power : LUX : 66 000 @ 2m, 16 500 @ 4,5 m
CREE 3W LED's : 28xR , 28xG , 26xB , 26xW
EXECUTION
Aluminum construction with plastic www.flash-butrym.pl Strona 4
Two side handles for transportation
Degree of protection: IP20
INSTALLATION
Two handles for screw hooks
Indoor use only
Mounting head in any position
Minimum distance to illuminated surfaces : 1 mouth
Keep a minimum distance from the surrounding area of the head : 0.5 m
CONNECTORS
Power connector IN: Neuritic Power-Con
Power connector OUT : Neuritic Power-Con
DMX512 signal connector : 3-pin XLR ( IN, OUT )
ELECTRICAL
Power supply : AC 110V - 240V , 50/60Hz
Maximum power consumption: 320W
Protection: T6 , 3A
ACCESSORIES INCLUDED
IN Power-Con power cable (blue connector )
Brackets for attaching the head to the structure ( 1pc )
Filter Wash - 25 °
User manual
USEFUL INFORMATION FOR ORDERING
Packaging ( 1unit ) : 410x390x285mm
Gross Weight: 9.8 kg
3. How To Set The Unit
3.1 Control Panel
Display
www.flash-butrym.pl Strona 5
To show the various menus and the selected functions
Led
DMX
MASTER
Slave
Sound
Button
MENU
DOWN
UP
ENTER
On
On
On
Flashing
DMX input Present
Master Mode
Slave Mode
Sound activation
To select the programming functions
To go backward in the selected functions
To go forward in the selected functions
To confirm the selected functions
DMX Address 001
512
Channel Set
Show Mode
9CH
12CH
16CH
SHOW1
SHOW2
SHOW3
SHOW4
Slave Set
Black Out
SLAVE1
SLAVE2
YES
NO
Sound Mode
MENU
Sound Sense
Pan Inverse
Tilt Inverse
ON
OFF
0
100
YES
NO
YES
NO www.flash-butrym.pl Strona 6
White Balance
Temp.
Defaults
NO
YES
Fixture Reset NO
YES
RED
GREEN
BLUE
PAN
TILT
RED
BLUE
DIMMER
31*C
125
255
0
255
Pro Defaults
Auto Defaults
DMX Controller
By using a universal DMX Controller to control the units, you will need to set DMX address from 1 to 512 so that the units can receive DMX signal Press the MENU button up to when the DMX Address is showing on the display. Pressing ENTER www.flash-butrym.pl Strona 7
button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press the ENTER button to setup, to go back to the functions without any change press the MENU button again. Hold and press the MENU button about one second or wait for one minute to exit the menu mode.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
Channel mode
9 channels
1 2 channels
16 channels
Unit 1
Address
1
1 fit
Unit 2
Address
10
13
17
4.4 DMX 512 Configuration 9 Channel Mode:
Unit 3
Address Unit 4 Address
19
25
28
37
33 49
Channel List Value
CH1
CH2
000-255
000-255
CH3
CH4
000-255
000-255
CH5
CH 6
CH7
CH 8
CH9
000-255
/ 000-255
000-255
000-255
240 - 255
Function
Pan(0-630)
Tilt(0-240)
Strobe
Red (0%-100%)
Green (0%-100%)
Blue (0%-100%)
White (0%-100%)
Dimmer (0%-100%)
Reset 240/255 Sound
12 Channel Mode:
Channel List Value
CH1
CH2
CH3
000-255
000-255
000-255
Function
Strobe Effect
Dimmer (0%-100%)
Pan(0-630)
CH4
CH5
CH 6
CH7
CH 8
CH9
CH10
CH11
CH12
000-255
000-255
000-255
000-249
000-255
000-255
000-255
000-255
000-255
16 Channel Mode:
Channel List Value
CH1
CH2
CH3
CH4
CH5
000-255
000-255
000-255
000-255
000-255
000-255 CH 6
CH7
CH 8
CH9
000-255
000-240
000-255
Pan Fine(Least significant bit)
Tilt (0-240)
Tilt Fine(Least significant bit)
Reset 250-255 Sound Activat
< T
Color Effect
C7
Red (0%-100%)
Green (0%-100%)
Blue (0%-100%)
White (0%-100%)
Function
Pan(0-630)
Pan Fine(Least significant bit)
Tilt (0-240)
Tilt Fine(Least significant bit)
Pan & Tilt Speed
Pan & Tilt Auto Run
Auto Run Speed
Reset 240 / 255 Aoto run color
Dimmer (0%-100%)
A
^ www.flash-butrym.pl Strona 8
CH10
CH11
CH12
CH13
CH14
CH15
CH16
000-255
000-255
000-255
000-255
000-255
000-255
000-255
Strobe
Red (0%-100%)
Green (0%-100%)
Blue (0%-100%)
White (0%-100%)
Color Auto Run
Color Auto Run Speed
Reset
Press the MENU button up to when the Reset is blinking on the display. Pressing
ENTER button and all channels of the unit will return to their standard position.
EC-Declaration of Conformity
Electromagnetic Compatibility (EMC) Directive
89/336/EEC.
We declare that our products (lighting equipment) comply with the following specification and bears CE mark in accordance with the provision of the
EN55014-2:1997A1:2001;EN61000-4-2:1995;EN61000-4-3:2002; EN61000-4-
4:1995; EN61000-4-5:1995; EN61000-4-6:1996,
EN61000-4-11:1994
&
Harmonized Standard
EN60598-1:2000+ALL: 2000+A12:2002 Safety of household and similar electrical appliances Part 1:General requirements www.flash-butrym.pl Strona 9
