Instruction Manual
50 memories time switch
3
OVR
!
OK
reset
1.
Prog.
page
Safety Precautions .........................................................4
Symbols, Keys ..............................................................5
Initial Start - Up ...........................................................6
Program Structure ..........................................................7
Setting 24h or AM/PM clock, Time and Weekday .......................11
Change for Daylight Savings time ........................................12
Operating Mode ............................................................13
Warranty ....................................................................14
!
4
Safety precautions
· The connection and installation of electrical devices may only be
carried out by a qualified electrician.
· Interventions in and changes to the device result in the voiding of
the warranty claim.
· Observe your national regulations and the respective safety
provisions.
· Switch-off commands have priority over switch-on commands.
OK
reset
5
A
B
C
D
General information
· The middle communication line shows the selectable menu item. If
confirmed with OK, this item is activated.
· Flashing texts or symbols require an entry.
· If no entries are made within the next 2 minutes, the clock reverts
to Auto mode.
1 6 12 18 24
C1
15:26:38
E
F
G
1 OVR Res.
MENU
H
I
K
J
Display
A Function displays of the two left-hand buttons
B Channel status displays
= Channel 1 ON
= Channel 1 OFF
Channel 1 = C1, Channel 2 = C2
C 3 communication lines for time display, menu items, entry prompts
etc.
D Day-of-week display
E Overview of daily switching program
F Display of daylight savings time
G Operating voltage (permanently lit dots)
Reserve power operation (dots flash)
H Function displays of the two right-hand buttons
Buttons
I Reset
The programs are retained in the case of a reset. The date and time
must be set again. Press reset button with a blunt object (pen).
J Right-hand buttons
K Left-hand buttons with manual switch function in Automatic mode
OK
reset
Function displays of the two left-hand buttons: scroll up in menu scroll down in menu
Select/reject suggestion
Select/accept suggestion
+ Press briefly = +1 Press and hold (approx. 2 sec) = +5
- Press briefly = -1 Press and hold (approx. 2 sec) = -5
6
Function displays of the two right-hand buttons:
MENU Exits the Automatic mode and enters the Programming mode
ESC Press briefly = one step back
OK
Press and hold (approx. 2 sec) = return to Automatic mode
Make selection and apply
EDT Change request in Read mode
NO Do not execute command
YES Execute command
DEL Delete
1.
Initial start-up - selection of menu language
1 6 12 18 24
C1
15:26:38 12H 24H
1 OVR
MENU
Res.
ESC OK
MENU
DEUTSCH
FRANCAIS
ESC OK
Info
In the delivered state the time switch is in the Auto mode with a preset time, date and the menu language English.
Prog.
1 6 12 18 24
C1
15:26:38
1 OVR
MENU
Res.
DATETIME
PROGRAM
DAYLIGHT
ESC OK
MENU
REVIEW
NEW
DELETE
ESC OK
7
New program
Info
The time switch has 50 memory spaces.
REVIEW
NEW only with 2-channel version
ESC OK
FREE 50
OK
I
CHANNEL
SELECT
OK
I
CHANNEL
SELECT
ESC OK
Example
ON command for channel 1 at 3 pm. OFF command at 6 pm.
· Select NEW program and confirm with OK.
· The free memory spaces are briefly displayed.
· Select channel and confirm with OK.
Prog.
SELECT
DAY
ESC OK
HOURS
00
CHL ON
ESC OK
MINUTES
15: 00
CHL ON
ESC OK
· Select day block or individual day (block formation as desired)
and confirm with OK.
· Enter hour for ON command (+/-) and confirm with OK.
· Enter minute for ON command ( +/-) and confirm with OK.
8
HOURS
OK
00
CHL OFF
ESC OK
MINUTES
18: 00
CHL OFF
ESC OK
SAVED
P01 P02
· Enter hour for OFF command (+/-) and confirm with OK.
· Enter minute for OFF command (+/-) and confirm with OK.
· Program is saved.
· Program jumps to selection REVIEW, NEW, DELETE. Now additional
programs can be created.
Prog.
View, edit program
DELETE
REVIEW
NEW
ESC OK
ON P01
15:00
EDT OK
OFF P02
18:00
EDT OK
Info
· The program steps can be scrolled through with .
· The respective program can be edited by pressing EDT.
The procedure is the same as when creating a new program.
9
Delete all programs
NEW
DELETE
ESC OK
DELETE
ALL
OK
YES NO
CONFIRM
OK
N O Y E S
Info
· It is possible to delete all programs with YES
· By pressing NO, individual programs can be deleted.
Prog.
10
Delete individual programs
DELETE
ALL
OK
YES NO
ON P01
15:00
HH:MM
DEL OK
CONFIRM
OK
N O Y E S
Info
When deleting individual programs, the corresponding program steps are deleted (e.g. P01 ON and P02 OFF).
11
Setting 24h or AM/PM Clock, Time and Weekday
LANGUAGE
DATETIME
PROGRAM
ESC OK
YEAR
20 07
OK
Info
The date and time are preset at the factory.
MONTH
2007: 03
ESC OK
ESC OK
DAY
2007:03: 25
ESC OK
HOURS
OK
13
ESC OK
MINUTES
13: 45
ESC OK
Set AM/PM (12-hour-) or 24-hour display
DAYLIGHT
12H 24H
ESC OK
AM PM
24H
OK
ESC OK
12
Switchover for daylight savings time
PROGRAM
DAYLIGHT
12H 24H
ESC OK
CALIBRAT
AUTO
NO
ESC OK
Info
The following settings are possible:
AUTO
Factory presetting of the published calendar dates. This is automatically recalculated for each year.
NO
No switchover
CALIBRAT
Programming for the start and ending date of daylight savings time must be entered for this purpose. The factory presetting is overwritten. The programmed daylight savings time is automatically recalculated for each year. The changeover takes place on the same specified day of the week in the same week of each month.
NO
CALIBRAT
AUTO
ESC OK
SU START
03
MONTH
ESC OK
SU START
03: 21
DAY
ESC OK
WI START
10
MONTH
ESC OK
WI START
10: 31
DAY
ESC OK
SU WI
2103:3110
CALIBRAT
ESC OK
OVR
Operating mode
1 6 12 18 24
C1
15:26:38
1 OVR
Res.
MENU OVR ON
OVR
OVR OFF OVR
AU TO : (no display)
programmed switching times
Info
Left-hand button = Channel 1
Right-hand button = Channel 2 (only with 2-channel version)
Press 1 x = OVR ON
= Continuous ON until next command is executed
Press 2 x = OVR OFF
= Continuous OFF until next command is executed
Press 3 x = return to Auto mode
13
LIMITED WARRANTY
Warranty service is available by either
(a) returning the product to the dealer from whom the unit was purchased or
(b) completing a warranty claim online at www.intermatic.com. This warranty is made by: Intermatic Incorporated,
Customer Service 1950 Innovation
Way, Suite 300, Libertyville, IL 60048.
For warranty service go to: http://www.
Intermatic.com or call 815-675-7000.