User manual | SIP Trunk Configuration Guide for the Vertical Xcelerator IP
Add to my manuals4 Pages
advertisement
Vertical Style Guide
Logos
Vertical Xcelerator IP SIP Trunk Configuration Guide for CBeyond BeyondVoice with SIPconnect
SIP Trunk Configuration Guide for the Vertical Xcelerator IP
CBeyond BeyondVoice with SIPconnect
September 2008
Vertical Communications Confidential and Proprietary © 2008
Vertical Xcelerator IP SIP Trunk Configuration Guide for CBeyond BeyondVoice with SIPconnect
Introduction
Configuring the Vertical Xcelerator IP for use with Cbeyond’s BeyondVoice® SIPconnect service offers significant cost savings as well as enhanced voice quality compared to using
PSTN trunks from the local incumbent telephone company.
SIPconnect is an industry standards approach to direct IP peering between IP-PBXs and
SIP service provider networks. If you would like more information about the SIPconnect
Interface Specification, which was defined by the SIP Forum in their Service Provider to IP
PBX Interoperability Task Group, see http://www.sipforum.org/sipconnect .
Pre-Requisites
• Please read this document carefully before beginning your install.
• Make sure you have the CBeyond SIP trunk account information handy.
• It is advisable to have attended a CBeyond training class for BeyondVoice configuration.
• The Xcelerator IP Firmware must be v1.5.11.1 or higher.
Constraints
• For best performance, fax machines should be directly attached to the analog ports on the CBeyond IAD.
• If configuring Xcelerator IP behind an existing firewall, please make sure you open and/ o r forward the appropriate ports on the firewall to the WAN interface of the Xcelerator IP.
Vertical strongly recommends the use of a SIP-aware firewall. Examples include devices from Intertex, Ingate, and SonicWall. For more information on configuring Xcelerator IP behind a firewall, please read the Xcelerator documentation.
Vertical Communications Confidential and Proprietary © 2008
Vertical Xcelerator IP SIP Trunk Configuration Guide for CBeyond BeyondVoice with SIPconnect
Xcelerator IP SIP Trunk Configuration for CBeyond Service
• From the main Xcelerator configuration page, select the Voice/Trunk/IP Trunk menu.
• Enter the PBX Username for the first trunk from the CBeyond Install Profile into the
Phone Number, Auth ID and User Name fields.
• Enter the PBX Password for the first trunk from the CBeyond Install Profile into the
Auth Password field.
• Enter the SIPconnect Domain for the first trunk from the CBeyond Install Profile into the
SIP Proxy and Register Server fields.
• Enter the SIPconnect Outbound Proxy for the first trunk from the CBeyond Install
Profile into the Outbound Proxy and Outbound Registrar fields.
• Change the Register Expires field entry to 3600 in the Register Expires field.
• Change the Support DID field entry to Yes
• Configure additional SIP trunks with the information provided in the CBeyond Install
Profile; however, on these trunks, change the Register Status field entry to Off and the
Support DID field entry to Yes.
Vertical Communications Confidential and Proprietary © 2008
Vertical Xcelerator IP SIP Trunk Configuration Guide for CBeyond BeyondVoice with SIPconnect
• To configure the DID Table, enter the DID Number, the Outgoing Call ID, the
Extension Number you are assigning the DID and the Display Name to send.
• Once you have configured the SIP trunks and the DID routing table, save your settings.
To verify your settings have been correctly entered, select the Diagnostics menu. All the status fields should be green and status should be PASS or IDLE.
To verify correct operation of the SIP trunks and DID routing, make several simultaneous inbound and outbound calls.
Vertical Communications Confidential and Proprietary © 2008
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project