Uniden EX905 Specifications

Uniden EX905 Specifications
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Included with the EX 905/925 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Important Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Telephone Line Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Radio Interference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
More Than One Cordless Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Telephone Line Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the Telephone Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Applying Power to the Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adapter Safety Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Desk or Tabletop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Direct Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting Up Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Raising the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing the Handset Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning the Battery Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Charging the Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setting the Pulse/Tone Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting Ringer Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Automatic Digital Code Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Using Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Making and Receiving Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Changing Channels, Flash, and Page/Find . . . . . . . . . . . . . . . . . . . . . . 25
Programming Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Storing a Number in Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Storing a Mixed Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Dialing a Stored Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Chain Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Erasing a Stored Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
EX 905/925
1
May 23, 1996 - Final Draft
14cm x 21cm
Important Safety Instructions
When using your telephone equipment, these basic safety precautions
should always be followed to reduce the risk of fire, electrical shock, and
injury to persons:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Use a dry
cloth for cleaning without liquid or aerosol cleaners.
4. Do not use this product near water; for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement, or near a
swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The
telephone may fall, causing serious damage to the unit.
6. Slots and openings in the cabinet and the back or bottom are
provided for ventilation. To protect the product from overheating,
these openings must not be blocked or covered. This product should
never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless proper
ventilation is provided.
7. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your dealer or local power
company.
8. Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be damaged by persons walking on it.
9. Do not overload wall outlets and extension cords, as this can result in
the risk of fire or electrical shock.
10. Never push objects of any kind into this product through cabinet
slots, as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electric shock. Never spill liquid of
any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this product.
Take it to qualified service personnel when service or repair work is
required. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
12. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
2
EX 905/925
D. If the product does not operate normally when following the
operating instructions. (Adjust only those controls that are covered
by the operating instructions. Improper adjustment of other
controls may result in damage and will often require extensive
repair work by a qualified technician.)
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
Battery Safety Precautions
Caution:
To reduce the risk of fire or injury to persons by the battery,
read and follow these instructions:
1. Use only the appropriate type and size Battery Pack specified in this
Operating Guide.
2. Do not dispose of the Battery Pack in a fire. The cell may explode.
Check the Nickel-Cadmium Battery Disposal package insert for
disposal instructions.
3. Do not open or mutilate the Battery Pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic if
swallowed.
4. Exercise care in handling the battery in order not to short the battery
with conducting materials such as rings, bracelets, and keys. The
battery or conductor may overheat and cause burns.
5. Charge the Battery Pack provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the instruction manual provided for this product.
6. Observe proper polarity orientation between the Battery Pack and
battery charger.
SAVE THESE INSTRUCTIONS
EX 905/925
3
Introduction
Congratulations on your purchase of the Uniden EX 905/925 Cordless
Telephone. This phone is designed to exacting standards that provide
reliability, long life, and outstanding performance.
Features
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
ò
900 MHz Long-range
Secure Digital Transmission
UltraClear Plus
AutoTalk™
10-Number Memory
Redial, Flash and Pause
AutoSecure™
Pulse/Tone Dialing
AutoStandby™
1-way Page/Find Button
14 Day Battery Life
AutoTalk™ allows you to answer a call by just removing the Handset
from the Base so you don’t have to waste time pushing buttons or
flipping switches. AutoStandby™ allows you to hang up by simply
returning the Handset to the Base.
The UltraClear Plus compander circuitry, virtually eliminates
background noise and provides you with the best possible reception
during all of your conversations.
To protect you against misbilled calls which might result from your
phone being activated by other equipment, Random Code™ digital
security automatically selects one of over 65 thousand digital security
codes for the Handset and Base Units. Also, the AutoSecure™ feature
electronically locks your phone when the Handset is in the Base.
To get the most from your phone, please read this Operating Guide
thoroughly. Also, be sure to complete the Product Registration Form and
mail it in.
4
EX 905/925
EX 905/925
Handset
Base Unit
AC Adapter
Rechargeable
Battery
Long Telephone
Cord
Short Telephone
Cord
Beltclip
Operating Guide
OMEX905/925
Other Printed
Material
5
d
goo
allof the
ago
e for
tim the aid
yeasa new
y
is the e tosco
tore th
Now to comd r
men rfor Libert
the
Fou s Fou
set
in
men ty.goo
the
ed
ty.
men
to
all
her
to
e fat
s set
ceiv
par
par
our
ck
in
e for
her ed
com
con
the
ted
t allqui
our
tim toof
ago
fat in
ica tha
ion
the
ceiv
the
The
ved
aid
men
ded
our
yeas
nat
on
d
is the
cei con
on are
to
al. over time
there
iti
Now egoo
ago
iti
tosco
con
ion
ck
and
ted
d equ
pos
pos
men
all r yeas
the e to
fox
nat
ion
qui
com
ica
ate
wnped
is
is jum
pro
pro
re nat
all
ded
The
e for Fou
a new
Now to com
Now
t cre
the
fox
ck bro Now
ty.sco
tim
are
th to
l.
al.
aid
l.
l.
tha
a new
wn
qui
to
y and
wal
par th
for
wal
d men
equ
on wal
the
The den
is the
ert d
ty.
d
ted
den goo
forica
d men
den bro
Lib
e to
Now of the
ate iti
goo
par
gar all
gar al.
set
com gar
crepos
the
r goo
ty.
all
the
aid hers and ded
all
thed equ
of
tor thefo4
r ate
are pro
par
the
for aid of ago
ove fo4r
aid
y
e to
cre d men
ove
fat
to
the
men
e
e
the
ped
men
ert
tim
r
our
d
the
yeas
goo
tim aid of
comago goo
jum
Lib t all jumped
a newy
the
Fou
in
re
to
the
e to
isved
ty.
set forth
all
ert
tha wn fox fo4r all is e to the
com
yeas
Nowcei
on
rs sco
d men
par
to
in in Lib the
her
re e for
iti
com goo
Fou
the
set
bro time
con
ty.
ck s ed
men
tim
fat
of
sco
pos
ed
ty.
all rthe
ceiv
the
men
to
ion
par
qui
her
aid
the
our
isto
ceiv
par
pro
is nat
con
Fou
Thefat
the
e for Now
are t allquick
Nowcon
of the
ted
theago
ion
ty. a new
our
tim
e to
al.
tedaid
l.
ica tha
ion
fox
to
yeas
the
The
par thcom
ica
wal
equ nat
thededmen
nat
re a
is the
d new
on wn Now
ted
al. over time
to
for sco
bro
den ded
t all
e
iti
Now of the
ate gar
ck
equ
and
andcom
set dedica
d l.
tha
pos
creth
qui ate
to is the e to
ped
wal
for
aid hers
they toon
The
pro
jum
ert
r
men
are
and
den
com
cre
iti
men
Lib d
al. are
ove
faterty
foxd l. Now
to
gar goo
men
pos
wn
goo
ty. d men
proated equr ther
wal
Lib t all jumped
all
bro
par
ty.
d
goo par
den
to
tha wn fox fo4r all cre ped ovee fo4of
the
goo
d men r
r all
tim aid gar
jum
bro time
of the
Foufor allof the
ty.
fo4 aid goo
the
ty. e
ago
par
is the
aid
the
s set
theallpar tim
e to
the
in
yeas
e for
new
her to
com
of the
the
re th a
tim
of the
e edsco
isfat
ceiv
aid Now
com
ourto
r the for
is the
con
to
are
Now e to the ago men
ionty.
s set
tedFou
men
fox
nat
her
com re yeas
ica
par
all brown Now
ded
t fat
sco th a new
ck
our
and
tha
qui wall. to
forerty
on
The
d men
Lib positi al. garden
goo
proated equr ther all party.
to
cre ped ovee fo4
the
d men
tim aid of
jum
goo
the
all
is the
e to
e for
com
tim
is the
Now
If any of these items are missing or damaged, contact Uniden Customer
Service at: (800) 297-1023, 8:00 a.m. to 5:00 p.m. Central, Monday
through Friday.
Included with the EX 905/925
Important Electrical Considerations
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and
damage any device connected to it. This phone is no exception.
Warning!
Please do not attempt to unplug any appliance during an electrical storm.
Caution:
Changes or modifications to this product not expressly
approved by Uniden, or operation of this product in any
way other than as detailed by this Operating Guide, could
void your authority to operate this product.
Range
Your new phone is designed to achieve the maximum possible range by
transmitting and receiving according to the highest specifications set
forth by the FCC. We have rated this phone to operate at a maximum
distance with the qualification that the range depends upon the
environment in which the telephone is used. Many factors limit range,
and it would be impossible to include all the variables in our rating. The
Maximum Range rating of this phone is meant to be used as a means of
comparison against other range claims.
Telephone Line Problems
The FCC has granted the telephone company the right to disconnect
service in the event that your phone causes problems on the telephone
line. Also, the telephone company may make changes in facilities and
services which may affect the operation of your unit. However, your
telephone company must give adequate notice in writing prior to such
actions to allow you time for making necessary arrangements to continue
uninterrupted service.
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem. If
you determine that it is the cause, you must leave it disconnected until
the trouble has been corrected.
6
EX 905/925
Radio Interference
Radio interference may occasionally cause buzzing and humming in your
cordless Handset, or clicking noises in the Base Unit. This interference is
caused by external sources such as TV, refrigerator, vacuum cleaner,
fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If
these noises continue and are too distracting, please check around your
home to see what appliances may be causing the problem. In addition,
we recommend that the Base not be plugged into a circuit that also
powers a major appliance because of the potential for interference. Be
certain that the antenna on the unit is fully extended when needed.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving radio
signals from another cordless telephone or other source of interference.
If you cannot eliminate this type of interference, you need to change to a
different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs. To
minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR. If
interference is experienced, moving the cordless telephone farther away
from the TV or VCR will often reduce or eliminate the interference.
More Than One Cordless Telephone
If you want to use more than one cordless telephone in your home, they
must operate on different channels. Press the channel key to select a
channel that provides the clearest communication.
EX 905/925
7
Installation
Selecting a Location
Before choosing a location for your new phone, there are some
important guidelines you should consider:
ò The location should be close to both a phone jack and continuous
power outlet. (A continuous power outlet is an AC outlet which does
not have a switch to interrupt its power.)
ò Keep the Base Unit and Handset away from sources of electrical noise
such as motors or fluorescent lighting.
ò Be sure there is sufficient space to fully extend the Base Unit antenna.
ò The Base Unit can be placed on a desk or tabletop or mounted on a
standard AT&T or GTE wall plate.
ò You should charge your new phone for 15-20 hours before
completing the installation or using the Handset.
Telephone Line Outlets
There are two types of phone outlets:
Modular Jack
Most phone equipment available now uses modular jacks. Phone cords
are fitted with a molded plastic connector which plugs into this type of
jack. If you do not have modular phone jacks, contact your local
telephone company for information about their installation.
Hard-wired Jack
Some equipment is wired directly to a phone jack, and these types of
installations require a modular jack converter. This type of installation is
not difficult; however, you should contact your Uniden telephone dealer
or a telephone supply store for advice about the proper adapter or
converter for your particular situation.
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cords:
Caution!
ò Never install telephone wiring during a lightning storm.
ò Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected.
ò Use caution when installing or modifying telephone lines.
8
EX 905/925
Applying Power to the Base Unit
This phone requires an AC
outlet, without a switch to
interrupt power, and the
included AC adapter. To relieve
strain on the DC plug when the
phone is placed on a desk or
table, connect the adapter as
shown below.
Wrap the power cord around
the strain relief notch on the
bottom of the Base Unit.
[ Place the power cord so that it does not create a trip hazard, or
where it could become chafed and create a fire or other electrical
hazards.
Adapter Safety Feature
The AC adapter furnished with
this phone may be equipped
with a polarized line plug — a
plug having one blade wider
than the other. This plug will fit
into the power outlet only one
way. If you are unable to insert
the plug fully into the outlet, try
reversing the plug.
Do Not alter the shape of the blades of the polarized plug!
[ If you cannot plug the AC adapter into the outlet, contact someone
about replacing the outlet.
EX 905/925
9
Desk or Tabletop Installation
1. Place the Base on a desk or tabletop.
[ In desk or table top installation,
the Handset is designed to stand
only vertically in the Base Unit.
DO NOT lay the Handset down
on the Base Unit.
2. Plug the AC Adapter cord
into the 9 VDC input jack on
the Base Unit.
3. Place the AC Adapter cord
around the strain relief notch.
10
EX 905/925
4. Plug one end of the long
telephone cord into the
TEL LINE jack on the
Base Unit.
5. Plug the other end of the cord into
the telephone jack on the wall.
6. Plug the AC Adapter into a standard
120 VAC wall outlet.
[ Do not use an outlet
controlled by a wall switch.
Use only the Uniden AC Adapter supplied with this phone.
EX 905/925
11
Wall Installation
Standard Wall Plate Mounting
These phones are designed to be mounted on a standard AT&T or GTE
wall plate.
1. Plug the AC Adapter
into the Base Unit.
2. Place the AC Adapter cord around
the strain relief notch.
Then, put the AC Adapter cord
inside the molded channel.
12
EX 905/925
3. Plug one end of the short
telephone cord into the
TEL LINE jack on the
Base Unit.
Place the telephone cord
inside the molded channel
on the bottom of the
Base Unit.
Then plug the other end of
the telephone cord into the
modular jack on the wall.
4. Place the Base Unit on the
posts of the wall plate and
push down until it’s firmly
seated.
5. Plug the AC Adapter
into a standard 120 VAC wall
outlet.
[ Do not use an outlet
controlled by a wall switch.
EX 905/925
13
Direct Wall Mounting
If you do not have a standard wall plate, you can mount your phone
directly on a wall. Before mounting your phone, consider the following:
ò Select a location away from electrical cables, pipes, or other items
behind the mounting location that could cause a hazard when
inserting screws into the wall.
ò Make sure the wall material is capable of supporting the weight of the
Base Unit and Handset.
ò Use #10 screws with anchoring devices suitable for the wall material
where the Base Unit will be placed.
1. Insert two mounting screws
3-15/16 inches apart.
3/16 IN.
Allow about 3/16 of an inch
between the wall and screw heads
for mounting the phone.
3 15/16 IN.
2. Plug the AC Adapter
into the Base Unit.
14
EX 905/925
3. Wrap the AC Adapter cord around
the strain relief notch.
Then, put the AC Adapter cord
inside the molded channel.
4. Plug one end of the short
telephone cord into the TEL LINE
jack on the Base Unit.
Put the cord inside the molded
channel on the bottom of the Base Unit.
5. Place the Base Unit on the
screws and push down until
it’s firmly seated.
EX 905/925
15
6. Plug the other end of the telephone
line cord into the wall jack.
7. Plug the AC Adapter into a standard
120 VAC wall outlet.
[
16
Do not use an outlet
controlled by a wall switch.
EX 905/925
Setting Up Your Phone
Raising the Antenna
Before using your phone, be sure
to raise its antenna to the vertical position.
Installing the Handset Battery Pack
1. Press in on the Battery Cover Release
and slide the battery compartment cover down.
2. Align the plastic connector of the
Nickel-Cadmium battery pack with
its socket and plug it in.
[ The black lead will be
on the left when the plug
is properly aligned.
EX 905/925
17
3. Place the battery pack inside the
battery compartment, and slide
the battery cover back on.
Cleaning the Battery Contacts
To maintain a good charge, it is
important to clean all charging
contacts on the Handset and
Base Unit about once a month.
Use a pencil eraser or other
contact cleaner. Do not use any
liquids or solvents.
18
EX 905/925
Charging the Battery Pack
Initial Battery Charging
The rechargeable Nickel-Cadmium battery
pack must be fully charged before using
your phone for the first time. We recommend
that the battery pack charge for approximately
15-20 hours, without interruption, before
plugging the phone line into your new phone.
1. Place the Handset on the Base Unit.
[
In desk or table top use,
the Battery charges only
in the vertical position.
—or—
Hang the Handset on the cradle
when the phone is mounted on a wall.
2. Make sure the status LED lights. If
the LED doesn’t light, check to see
that the AC adapter is plugged in,
and that the Handset is making
good contact with the Base Unit
charging contacts.
EX 905/925
19
Continuous Battery Charging
For the best battery performance, return the Handset to the Base Unit at
the end of the day. This keeps the battery fully charged, so your phone
works best.
Low Battery Indicator
When the Battery Pack in the Handset
is very low and needs to be charged,
the talk • batt low LED flashes.
If the talk • batt low LED begins to flash, the phone is programmed to
eliminate its functions to save power. The table below describes what to
do to return your phone to normal operation.
During a Call
In Standby Mode
Only the talk button operates.
None of the buttons will operate.
The Handset beeps and the
talk • batt low LED flashes once
every 3 seconds.
The Handset talk • batt low LED
flashes once every 3 seconds.
Complete your call as quickly as
possible.
You will not be able to make a call.
Return the Handset to the Base Unit
for charging.
Return the Handset to the Base Unit
for charging.
[ Allow 15 to 20 hours without any interruption for the Handset to
fully recharge.
Setting the Pulse/Tone Switch
Be sure the PULSE/TONE switch is
in the TONE position.
[
20
Most phone systems are
Tone dialing. Check with your
local phone company if you are
not sure whether your system is
Tone or Pulse dialing
EX 905/925
Adjusting Ringer Controls
Ringer Tone and Volume
While the phone is not in use,
press ringer.
The phone has two ringer tones
with two volume levels one soft and one loud.
Each time you press ringer,
the ringer/volume changes.
Receiver volume
While you are on a call,
press volume.
The phone has two receiver
volume levels - one soft and one loud.
Each time you press volume,
the receiver volume changes.
EX 905/925
21
Automatic Digital Code Security
To avoid unauthorized calls on your phone, a Digital Code was added to
all EX 905/925 phones. This Digital Code is shared only between the
Handset and Base Unit. The Code is set automatically when you first
use the phone.
To change the Digital Code, be sure the Handset is on the Base, then:
1. Remove the Handset from the Base Unit.
2. Press page/find on the Base Unit.
3. While the Handset is still beeping,
place it back on the Base Unit.
4. When the beeping stops, briefly
remove the Handset again, and
then return it to the Base Unit.
The status LED will blink to
indicate that the Digital Security
Code is set to one of the more
than 65,000 codes.
22
EX 905/925
If the Base Unit loses power while the Handset is off the Base,
the Digital Code may be erased. If this happens, the Handset will not
function. To reestablish communication between the Handset and
Base Unit:
1. Restore power to the Base Unit.
2. Place the Handset on the Base Unit.
3. The status LED blinks to
indicate that the Digital
Security Code is set.
EX 905/925
23
Changing the Beltclip
Attach the beltclip
1. Remove the slot cover.
2. Put the beltclip in the slot
and press down until it clicks.
Remove the Beltclip
1. Pull back on the release tab and pull up.
2. Replace the slot cover.
24
EX 905/925
Using Your Phone
Making and Receiving Calls
The following features of the EX 905/925 phones are different
depending on the Handset’s location when you make or receive a call.
ANSWER CALL
MAKE CALL
HANG UP
REDIAL
Handset On Base
Handset Off Base
Pick up Handset (AutoTalk).
Press talk.
1) Press talk.
1) Pick up Handset.
2) Press talk.
2) Listen for dial tone.
3) Listen for dial tone.
3) Dial the number.
4) Dial the number.
Press talk.
— OR —
Return Handset to Base. (AutoStandby)
1) Pick up Handset.
1) Press talk.
2) Press talk.
2) Listen for dial tone.
3) Listen for dial tone.
3) Press redial.
4) Press redial.
[ Sometimes when you press
talk to hang up the phone, you may get an
error tone and the phone will not disconnect. If this happens, place
the Handset on the Base Unit or press talk again while holding the
Handset close to the Base Unit.
Changing Channels, Flash, and Page/Find
To change channels or access call waiting while the phone is in use, or to
use the one-way page to locate the Handset, follow these steps:
CHANGING
CHANNELS
FLASH
PAGE/FIND
EX 905/925
Press These Keys
Press channel.
[ Change channels to help
eliminate background noise.
If the call waiting tone
sounds, press flash to accept
the waiting call.
— OR —
If you have finished a call and
want to make another call,
press flash to hang up and
get a dial tone.
Press page/find on the Base
Unit to locate the Handset.
You Will Hear
A click similar to when flash is
pressed. There may be a brief
pause as your phone searches
for a clear channel.
A click, a short pause, then the
caller (if you were on a call).
— OR —
A click, and then a dial tone so
you can make a different call.
The Handset will beep more
than 5 times.
25
Programming Your Phone
All programming functions must be completed when your phone is in
the standby mode because programming keys do not function while you
are on the phone.
Storing a Number in Memory
Use these keys to store a number
in memory.
[ An error tone will sound and
the programming procedure
will be canceled if more than
20 seconds elapse between each
keystroke entry or step.
1. Remove the Handset from the Base Unit.
2. Press mem.
The talk • batt low LED blinks.
5551212
3. Enter the number you want to
store (up to 16 digits).
4. If a pause is needed during dialing to access
a long distance service, press pause.
9pause
[ The
pause button counts as one digit. Pressing pause more than
once increases the length of the pause between numbers.
26
EX 905/925
5551212
5. Press mem again.
6. Enter the memory location (0-9).
✻ A tone indicates that the number is stored.
Storing a Mixed Number
If your phone is set up for Pulse dialing, you can store a mixed mode
number so that you can easily access long distance services.
Use these keys to store a mixed
mode number in memory.
✻ An error tone will sound
and the programming
procedure will be canceled if
more than 20 seconds elapse
between each keystroke entry
or step.
1. Remove Handset from the Base Unit.
2. Press mem.
The talk • batt low LED blinks.
EX 905/925
27
5551212
3. Enter the number to be
dialed in pulse mode.
4. Press tone on the Handset.
5. Enter the number to be dialed in tone mode.
3300
6. If a pause is needed during dialing to access
a long distance service, press pause.
The pause button counts as one digit. Pressing pause more than
once increases the length of the pause between numbers.
3300
[
7. Press mem again.
8. Enter the memory location (0-9).
A tone indicates that the number is stored.
28
EX 905/925
Dialing a Stored Number
To dial a number previously stored in memory, follow these steps:
1. Remove the Handset from the Base Unit.
2. Press talk.
3. Press mem.
4. Press the memory location number (0-9).
EX 905/925
29
Chain Dialing
On certain occasions, after dialing a number, you may be requested by
the party or service you are calling to enter a special access code, such as
when performing a banking transaction. To do this, simply:
1. Store the access code into one of the memory numbers.
2. Dial the main number.
3. At the appropriate time, press mem followed by the memory location
number where the access code is saved.
Erasing a Stored Number
To erase a number previously stored in a memory location (0-9),
follow these steps:
1. Remove the Handset from the Base Unit.
2. Press mem twice.
3. Press the memory location
number (0-9).
A tone indicates that the
number is erased.
If more than 20 seconds elapse between each keystroke entry or
[ step,
an error tone will sound and the erase procedure will be
canceled.
30
EX 905/925
Troubleshooting
If your Cordless Telephone is not performing to your expectations,
please try these simple steps. If you are still unable to resolve the
problems, contact Uniden Customer Service at (800) 297-1023, 8:00 a.m.
to 5:00 p.m. Central, Monday through Friday.
Problem
Charge light won’t come on
when Handset is placed in
Base Unit.
Suggestion
• Make sure AC Adapter is plugged into the Base
Unit and wall outlet.
• Make sure Handset is properly seated in
Base Unit.
• Make sure that the charging contacts on the
Handset and Base Unit are clean.
• If the phone is desk/table top installed, make
sure the Handset is in the vertical position.
Audio sounds weak and/or
scratchy.
• Make sure that the Base Unit antenna is
vertical.
• Move the Handset and/or Base Unit to
different locations and try again.
Can’t make or receive calls.
• Press channel to select another channel.
• Check both ends of the Base Unit telephone
line cord.
• Make sure the AC Adapter is plugged into the
Base Unit and wall outlet.
• Disconnect the AC Adapter for a few minutes,
and then reconnect it.
Handset doesn’t ring or
receive a page.
• Nickel-Cadmium battery pack may be weak.
•
•
•
•
Hear only continuous static
from Handset and phone will
not turn off.
•
•
•
Handset does not fully charge. •
EX 905/925
Charge the battery on the Base Unit
for 15 to 20 hours.
Raise the Base Unit antenna vertically.
The Handset may be too far away from the
Base Unit.
Place the Base Unit away from noise sources.
The Digital Security Code may be erased. Set
the Digital Code.
The power has been interrupted during a call.
Restore power to the Base Unit. Make sure the
phone is not plugged into an outlet controlled
by a wall switch.
If a power failure has occurred and power will
be out for some time, remove the battery from
the Handset. This will prevent the battery from
completely discharging.
If the phone is desk/table top installed, make
sure the Handset is in the vertical position and
the contacts are touching.
31
Specifications
General – The EX 905/925 complies with FCC Parts 15 and 68.
Frequency Control
PLL
Modulation
FM
Operating Temperature -10º to 50º C
Base Unit
Receive Frequency
Transmit Frequency
Power Requirements
Size
Weight
902.10 to 905.00 MHz (30 Channels)
925.00 to 927.90 MHz (30 Channels)
9 V 210 mA (from AC Adapter)
5-1/2 in.(W) x 2-1/2 in. (D) x 7-3/4 in. (H)
Approx. 11.1 oz.
Handset
Receive Frequency
Transmit Frequency
Power Requirements
Size (without antenna)
Weight
Battery
925.00 to 927.90 MHz (30 Channels)
902.10 to 905.00 MHz (30 Channels)
Rechargeable Ni-Cd Battery Pack
2 in. (W) x 2-1/4 in. (D) x 7-1/2 in. (H)
Approx. 10 oz. (including battery)
BT-905
Capacity
600 mAH, 3.6V
Talk Mode
7 hours
Standby Mode 14 days
Specifications, Features, and availability of Optional Accessories are all
subject to change without prior notice.
32
EX 905/925
May 23, 1996 - Final Draft
14cm x 21cm
UDUZ————
Precautions
Before you read anything else, please observe the following:
Warning!
Uniden America Corporation DOES NOT represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or damage to
the unit, DO NOT expose this unit to rain or moisture.
Rechargeable Nickel-Cadmium Battery Warning
n This equipment contains a Rechargeable Nickel-Cadmium Battery.
n Cadmium is a chemical known to the State of California to cause
cancer.
n The Rechargeable Nickel-Cadmium Battery contained in this
equipment may explode if disposed of in a fire.
n Do not short-circuit the battery.
n Do not charge the Rechargeable Nickel-Cadmium Battery used in
this equipment in any charger other than the one designed to
charge this battery as specified in this Guide. Using another
charger may damage the battery or cause the battery to explode.
Rechargeable Nickel-Cadmium Batteries
Must Be Recycled or Disposed of Properly
n Residents of Minnesota should contact 1-800-225-PRBA for
information concerning reclamation and disposal of Rechargeable
Nickel-Cadmium Batteries.
n Residents outside of Minnesota should contact their local
authorities for information concerning reclamation and disposal
of Rechargeable Nickel-Cadmium Batteries.
Controls and Keys
1. Talk/Batt Low Indicator – talk • batt low
2. Talk Key – talk
3. Numeric Keypad
4. Memory Key – mem
5. Ringer Tone-Volume (ringer)/Volume Key (volume)
6. Microphone
7. Redial Key – redial
8. Flash Key – flash
9. Channel Select Key – channel
10. Pause Key – pause
11. Page/Find Key – page/find
12. Charge LED Indicator – status
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this
Uniden Product to be free from defects in materials and craftsmanship with only the
limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no
further effect 12 months after the date of original retail sale. The warranty is invalid if the
Product is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered,
or used as part of any conversion kits, subassemblies, or any configurations not sold by
Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfunction covered by this warranty, (E)
used in any conjunction with equipment or parts or as part of any system not manufactured
by Uniden, or (F) installed or programmed by anyone other than as detailed by the Operating
Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at
any time while this warranty is in effect, warrantor will repair the defect and return it to you
without charge for parts, service, or any other cost (except shipping and handling) incurred by
warrantor or its representatives in connection with the performance of this warranty. THE
LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING
TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY
NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR
THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some
states do not allow this exclusion or limitation of incidental or consequential damages so the
above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. This warranty is void outside the United States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the
instructions in this Operating Guide you are certain that the Product is defective, pack the
Product carefully (preferably in its original packaging). Include evidence of original purchase
and a note describing the defect that has caused you to return it. The Product should be
shipped freight prepaid, by traceable means, or delivered, to warrantor at:
Uniden America Corporation
4700 Amon Carter Blvd
Fort Worth, TX 76155
(800) 297-1023, 8 a.m. to 5 p.m. Central, Monday through Friday
Covered under one or more of the following U.S. patents:
4,511,761
4,523,058
4,595,795
4,797,916
©1996 Uniden America Corporation.
Printed in Hong Kong
5,426,690
All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement