atupt1k0eo & atupt1k0eo1d - RVR Elettronica SpA Documentation

atupt1k0eo & atupt1k0eo1d - RVR Elettronica SpA Documentation
ATUPT1K0EO
& ATUPT1K0EO1D
USER MANUAL
Manufactured by R.V.R ELETTRONICA S.p.A. Italy
File Name:
ATUPT1K0EO& ATUPT1K0EO1D_ING_1.0.indb
Version:
1.0
Date:
23/07/2012
Revision History
Date
Version
23/07/2012 1.0
Reason
First Version
Editor
J. H. Berti
ATUPT1K0EO & ATUPT1K0EO1D - User Manual
Version 1.0
© Copyright 2012
R.V.R. Elettronica SpA
Via del Fonditore 2/2c - 40138 - Bologna (Italia)
Telefono: +39 051 6010506
Fax: +39 051 6011104
Email:
[email protected]
Web:
www.rvr.it
All rights reserved
Printed and bound in Italy. No part of this manual may be reproduced,
memorized or transmitted in any form or by any means, electronic
or mechanic, including photocopying, recording or by any information storage and retrieval system, without written permission of the
copyright owner.











ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
DECLARATION OF
CONFORMITY
We, the undersigned,
Manufacturer’s Name:
R.V.R. Elettronica SpA
Manufacturer’s Address:
Via del Fonditore 2/2c
I - 40138 Bologna
Italy
Certify and declare under our sole responsibility that the product:
Product Description:
Solid State Transmitter Station for analog TV
broadcasting Modulation:
PAL Standard UHF Band
Model:
ATUPT1K0EO
Variant:
ATUPT1K0EO1D
Frequency Range:
470.000 ÷ 862.000 MHz
RF Power Output:
100 ÷ 1000 WPS
when used for its intended purpose, is in compliance with the essential requirements and
other relevant provisions of Directive 99/5/CE “R&TTE”, and therefore carries the “CE” mark.
The conformity assessment procedure referred in Article 10 and detailed in Annex III of Directive
99/5/EC has been followed.
The following harmonized standard have been applied:
Radio (3.2):
EN 302 397
EMC (3.1b):
EN 301 489 - 1 + EN 301 489 - 11
Safety (3.1a):
EN 60215 + EN 60065
The technical documentation is held at the location above, as required by the conformity assessment
procedure.
Bologna, Italy, 03/09/2009
Ravagnani Stefano
Technical Manager
R.V.R Elettronica S.p.A.
User Manual
Rev. 1.0 - 23/07/12
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
Technical Specification
Frequency range:
Nominal RF power:
Power supply voltage:
Nominal exciting power:
Consumption:
ii
Rev. 1.0 - 23/07/12
UHF IV&V band 470 to 862
MHz
1000 WPS (PAL Standard )
220Vac
about 1W
about 2kW
User Manual
ELETTRONICA
ATUPT1K0EO & ATUPT1K0EO1D
Table of Contents
1.
2.
3.
3.1
3.2
4.
4.1
5.
5.1
5.2
6.
6.1
6.2 6.3
Preliminary Instructions
Warranty
First Aid
Electric shock treatment
Treatment of electric burns
General Description
Composition
Installation and Use
Installation
First Start
Equipment Quick Reference
Exciter (ATVTE)
Amplifier (ATVCA)
Changeover (SCML1+1SL)
User Manual
Rev. 1.0 - 23/07/12
1
1
2
2
2
3
3
5
5
5
7
7
7
8
iii
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
This page was intentionally left blank
iv
Rev. 1.0 - 23/07/12
User Manual
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
IMPORTANT
The symbol of lightning inside a triangle placed on the product, evidences the operations for
which is necessary gave it full attention to avoid risk of electric shocks.
The symbol of exclamation mark inside a triangle placed on the product, informs the user
about the presence of instructions inside the manual that accompanies the equipment, important for the efficacy and the maintenance (repairs).
Make sure both are properly connected.
1. Preliminary Instructions
Operation of this equipment in a residential area may cause
radio interference, in which case the user may be required
to take adequate measures.
• General Warnings
This equipment should only be operated, installed and
maintained by “trained” or “qualified” personnel who are familiar
with risks involved in working on electric and electronic circuits.
“Trained” means personnel who have technical knowledge of
equipment operation and who are responsible for their own
safety and that of other unqualified personnel placed under
their supervision when working on the equipment.
“Qualified” means personnel who are trained in and
experienced with equipment operation and who are
responsible for their own safety and that of other unqualified
personnel placed under their supervision when working on
the equipment.
The specifications and data contained herein are provided
for information only and are subject to changes without prior
notice. R.V.R. Elettronica S.p.A. disclaims all warranties,
express or implied.While R.V.R. Elettronica S.p.A. attempts
to provide aamplifierrate information, it cannot accept
responsibility or liability for any errors or inaamplifierracies
in this manual, including the products and the software
described herein. R.V.R. Elettronica S.p.A. reserves
the right to make changes to equipment design and/or
specifications and to this manual at any time without prior
notice.
• Notice concerning product intended purpose and use
limitations.
WARNING: Residual voltage may be present inside
the equipment even when the ON/OFF switch is set to
Off. Before servicing the equipment, disconnect the
power cord or switch off the main power panel and
make sure the safety earth connection is connected.
Some service situations may require inspecting the
equipment with live circuits. Only trained and qualified
personnel may work on the equipment live and shall be
assisted by a trained person who shall keep ready to
disconnect power supply at need.
R.V.R. Elettronica S.p.A. shall not be liable for injury to
persons or damage to property resulting from improper use
or operation by trained/untrained and qualified/unqualified
persons.
WARNING: The equipment is not water resistant.
Any water entering the enclosure might impair proper
operation. To prevent the risk of electrical shock or
fire, do not expose this equipment to rain, dripping or
moisture.
Please observe local codes and fire prevention rules when
installing and operating this equipment.
WARNING: This equipment contains exposed
live parts involving an electrical shock hazard. Always
disconnect power supply before removing any covers
or other parts of the equipment.
Ventilation slits and holes are provided to ensure reliable
operation and prevent overheating; do not obstruct or
cover these slits. Do not obstruct the ventilation slits under
any circumstances. The product must not be incorporated
in a rack unless adequate ventilation is provided or the
manufacturer’s instructions are followed closely.
WA R N I N G : T h i s e q u i p m e n t c a n r a d i a t e
radiofrequency energy and, if not installed in compliance
with manual instructions and applicable regulations,
may cause interference with radio communications.
WARNING: This equipment is fitted with earth
connections both in the power cord and for the chassis.
User Manual
This product is a radio transmitter suitable for frequencymodulation audio radio broadcasting. Its operating
frequencies are not harmonised in designated user countries.
Before operating this equipment, user must
obtain a licence to use radio spectrum from the
competent authority in the designated user country.
Operating frequency, transmitter power and other
characteristics of the transmission system are subject to
restrictions as specified in the licence.
2. Warranty
La R.V.R. Elettronica S.p.A. warrants this product to be free
from defects in workmanship and its proper operation subject
to the limitations set forth in the supplied Terms and Conditions.
Please read the Terms and Conditions carefully, as purchase
of the product or acceptance of the order acknowledgement
imply acceptance of the Terms and Conditions.
For the latest updated terms and conditions, please visit our web
site at WWW.RVR.IT. The web site may be modified, removed
or updated for any reason whatsoever without prior notice.
The warranty will become null and void in the event the
product enclosure is opened, the product is physically
damaged, is repaired by unauthorised persons or is used for
purposes other than its intended use, as well as in the event
of improper use, unauthorised changes or neglect. In the event a defect is found, follow this procedure:
1 Contact the seller or distributor who sold the equipment;
provide a description of the problem or malfunction for
the event a quick fix is available. Sellers and Distributors can provide the necessary
information to troubleshoot the most frequently encountered
problems. Normally, Sellers and Distributors can offer a
faster repair service than the Manufacturer would. Please
note that Sellers can pinpoint problems due to wrong
installation.
2 If your Seller cannot help you, contact R.V.R. Elettronica
S.p.A. and describe the problem; if our staff deems it
appropriate, you will receive an authorisation to return
the equipment along with suitable instructions;
3 When you have received the authorisation, you may
return the unit. Pack the unit carefully before shipment;
use the original packaging whenever possible and seal
the package perfectly. The customer bears all risks of
loss (i.e., R.V.R. shall not be liable for loss or damage)
until the package reaches the R.V.R. factory. For this
reason, we recommend insuring the goods for their full
value. Returns must be sent on a C.I.F. basis (PREPAID)
to the address stated on the authorisation as specified
Rev. 1.0 - 23/07/12
/ 10
ATUPT1K0EO & ATUPT1K0EO1D
by the R.V.R. Service Manager.
Figure 3
Figure 4
Figure 5
Units returned without a return authorisation may
be rejected and sent back to the sender.
•
One rescuer: give 2 quick rescue breaths after
each 15 compressions.
4 Be sure to include a detailed report mentioning all
problems you have found and copy of your original
invoice (to show when the warranty period began) with
the shipment.
•
Two rescuers: one rescue breath after each 5
compressions.
•
Do not stop chest compressions while giving
artificial breathing.
•
Call for medical help as soon as possible.
Please send spare and warranty replacement parts orders to
the address provided below. Make sure to specify equipment
model and serial number, as well as part description and
quantity.
ELETTRONICA
R.V.R. Elettronica S.p.A.
Via del Fonditore, 2/2c
40138 BOLOGNA ITALY
Tel. +39 051 6010506
3.1.2
3. First Aid
All personnel engaged in equipment installation, operation
and maintenance must be familiar with first aid procedures
and routines.
3.1
Electric shock treatment
3.1.1
If the victim is unconscious
If the victim is conscious
•
Cover victim with a blanket.
•
Try to reassure the victim.
•
Loosen the victim’s clothing and have him/her
lie down.
•
Call for medical help as soon as possible.
3.2
Treatment of electric burns
3.2.1
Large burns and broken skin
•
Cover affected area with a clean cloth or
linen.
•
Do not break any blisters that have formed;
remove any clothing or fabric that is stuck to
the skin; apply adequate ointment.
•
Administer adequate treatment for the type of
accident.
•
Get the victim to a hospital as quickly as
possible.
•
Elevate arms and legs if injured.
Follow the first aid procedures outlined below.
•
Lay the victim down on his/her back on a firm
surface.
•
the neck and tilt the head backwards to free
the airway system (Figure 1).
If medical help is not available within an hour, the victim is
conscious and is not retching, administer a solution of table
salt and baking soda (one teaspoon of table salt to half
teaspoon of baking soda every 250 ml of water).
Have the victim slowly drink half a glass of solution for four
times during a period of 15 minutes.
Figure 1
•
If needed, open the victim’s mouth and check
for breathing.
•
If there is no breathing, start artificial respiration
without delay (Figure 2) as follows: tilt the head
backwards, pinch the nostrils, seal your mouth
around the victim’s mouth and give four fast
rescue breaths.
Stop at the first sign of retching.
Do not administer alcoholic beverages.
3.2.2 Minor burns
Figure 2
•
/ 10
Check for heartbeat (Figure 3); if there is
no heartbeat, begin chest compressions
immediately (Figure 4) placing your hands in
the centre of the victim’s chest (Figure 5).
Rev. 1.0 - 23/07/12
•
Apply cold (not ice cold) strips of gauze or dress
wound with clean cloth.
•
Do not break any blisters that have formed;
remove any clothing or fabric that is stuck to
the skin; apply adequate ointment.
•
If needed, have the victim change into clean,
dry clothing.
•
Administer adequate treatment for the type of
accident.
•
Get the victim to a hospital as quickly as
possible.
•
Elevate arms and legs if injured.
User Manual
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
4. General Description
The ATUPT1K0EO & ATUPT1K0EO1D are RF solid-state transmitter for PAL analog TV
broadcasting , manufactured by R.V.R. Elettronica S.p.A. with 1000WPS of maximum
power output. It is fully solid-state apparatus of modern design that uses MOSFET
as active components in the TV amplifying modules. This chapter briefly describes the machine’s main features.
4.1 Composition
The ATUPT1K0EO is made up:
1 ATVTE005PU1 exciter
1 ATVCA1K0LU1 amplifier
User Manual
Rev. 1.0 - 23/07/12
/ 10
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
The ATUPT1K0EO1D is made up:
2 ATVTE005PU1 exciter
1 SCML1+1SL changeover
1 ATVCA1K0LU1 amplifier
The standard configuration of the ATUPT1K0EO & ATUPT1K0EO1D foresees
one 19” rack (see figure). The manufacturer will produce upon customers request
special configurations.
The amplifier is supplied complete with all its parts, not really “modules”, essential
for its operation such as the fans for dissipating the heat generated by the machine
inside the room and all the accessories for the electrical and RF wiring. As a rule,
the amplifier is supplied as a complete transmitter therefore the two TV exciters
that it manages will be provided and connected (a service exciter and a spare
exciter).
Note: This manual gives system-level information about the ATUPT1K0EO &
ATUPT1K0EO1D. Further details about the operation of the single components
please refer to the relative manuals, that are attached to the present one and
should be considered a part of it:
• STU05 (alias ATVTE)
• ATVCA1K0LU1
• SCML1+1SL
/ 10
Rev. 1.0 - 23/07/12
User Manual
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
5. Installation and Use
This chapter contains the basic instructions for installing and using the
ATUPT1K0EO & ATUPT1K0EO1D. If necessary, more depth information about
the operating principles may be found in the components’ manuals.
5.1 Installation
For practical reasons and for transport safety, the machine can be supplied
disassembled to the customer. The assembly procedure is rather simple and can
be carried out by any qualified technician.
Note: In order to avoid the risk of damaging the machine and/or of injuring the
operators, it is advisable to closely adhere to the instructions provided below.
always respect all the safety regulations and standards in force.
Unpack the transmitter and before any other operation check that the equipments
hasn’t been damaged during transport and all the controls and connectors on the
front and rear panels are in good condition.
To install the ATUPT1K0EO & ATUPT1K0EO1D transmitter please refer to the
relative technical dossier, particularily about:
• Mains supply connection
• RF connections
Perform the connections following the instructions and schematics given in the
station’s documentation (technical dossier).
5.2 First Start
This section describes the procedure for powering-on the machine the first time.
For a description of the power up procedure of the single amplifiers in the different
cases, of the use of the exciters and of the hybrid combiner, please consult the
relative manuals.
5.2.1 Preliminary Operations
Before activating the apparatus, please perform the necessary connections, that
is:
• Power supply
• Modulating signals
• RF amplifier section and load
User Manual
Rev. 1.0 - 23/07/12
/ 10
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
It is advisable to run the first tests connecting the transmitter to a suitable (for type
and power) dummy load rather than to the transmission antenna.
5.2.2 Power-on
When powering-on the transmitter the first time, perform the operations below to
work efficiently in less time as possible.
• Switch on the service mains supply.
• Keeping the exciter at its minumum power level. When power up, the ATVTE exciter display reports the frequency and power
level; if these are not as required, just switch it in OFF mode to temporarily
deactivate the power output.
• Switch on the mains power supply for all amplifiers.
• Enable the exciter currently connected to the amplifier and check the working
frequency. If necessary changed it.
• Rise its output power until the output power of the amplifier (the overall power indicated on Amplifier unit display) reaches its required value indicated in
technical dossier.
Note: during the RF output power rising, check the reflected power level (on
amplifier unit) to verify the antenna status.
The transmitter is now up and running at its nominal power level. It is then possible
to perform all the controls and verification that one thinks are necessary before
putting it into operation.
/ 10
Rev. 1.0 - 23/07/12
User Manual
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
6. Equipment Quick Reference
6.1 Exciter (ATVTE)
Note: not change the frequency until you have properly calibrated the output
filter.
• Set the exciters following the instructions of the exciters that you are used to
set the desired operating frequency. Adjust the output power of exciter to the
power required to drive your transmitter.
Before that you enable the delivered power from exciter, it is suggested to
check and, in case, correct the basic parameters under own necessity:
•
•
frequency power
6.2 Amplifier (ATVCA)
• Adjust the power of each amplifier through setting menu (SET); the overall
RF output emitted by transmitter appears on the power meter display, if it is
present.
User Manual
Rev. 1.0 - 23/07/12
/ 10
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
6.3 Changeover (SCML1+1SL)
• Set the changeover between exciters following the instructions below, if it is
present.

Before that you enable the delivered power from main exciter, it is suggested
to check and, in case, correct the basic parameters under own necessity:
•
•

local/remote status 

changeover

Note: Some information here contained may be not necessary for the proper

functioning
of your transmitter.
Note: turning the encoder, the cursor moves itself on indicators of the various
sub-menus, while in the middle of the window it shows the contents. If you press


the encoder
while the indicator of a menu is highlighted on navigation bar, and if
it contains adjustable parameters, the cursor moves within the central window of

the display,
allowing you to act on adjustable parameters. Every menu contains a

“EXIT” field: by pressing the encoder while this field is highlighted, you will leave
the submenu and return to navigation mode.









     



• Set the LOCAL/REMOTE switch to LOCAL position through General Setting
menu using MODE function, this is to enable local control of changeover. The
respective
LED lights on for confirmation.





TX1
: ON

TX2
: OFF

Change: Normal


Func. : AUTO
          
Mode : REMOTE

Reset : OK

IIC
: 10


Exit

/ 10


Rev. 1.0 - 23/07/12
User Manual
ELETTRONICA
ATUPT1K0EO & ATUPT1K0EO1D
• Set the changeover between the exciters through General Setting menu using
CHANGE function. The respective LED lights on for confirmation.
Note: all changes made will be briefly described by synoptic, which includes a
series of LED for the instantaneous vision of the exchange condition. It shows the
position of coaxial relay, the state of dummy load and of transmitter connects to
it.
User Manual
Rev. 1.0 - 23/07/12
/ 10
ATUPT1K0EO & ATUPT1K0EO1D
ELETTRONICA
This page was intentionally left blank
10 / 10
Rev. 1.0 - 23/07/12
User Manual
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
R.V.R Elettronica S.p.A.
Via del Fonditore, 2 / 2c
Zona Industriale Roveri · 40138 Bologna · Italy
Phone: +39 051 6010506 · Fax: +39 051 6011104
e-mail: [email protected] ·web: http://www.rvr.it
ISO 9001:2000 certified since 2000
The RVR Logo, and others referenced RVR products and services are trademarks of RVR Elettronica S.p.A. in Italy, other countries or both. RVR ® 1998 all rights reserved.
All other trademarks, trade names or logos used are property of their respective owners.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement