First Alert FA130cp - Wayne Alarm Systems

First Alert FA130cp - Wayne Alarm Systems
!
V
6HFXULW\6\VWHP
ARMED
READY
R
A
B
C
1 OFF
4 MAX
7INSTANT
READY
2 AWAY
5TEST
8 CODE
0
3STAY
6BYPASS
9 CHIME
#
D
FA2 60
ARMED
ON
READY
OFF
R
AWAY
STAY
1 OFF
4 MAX
7INSTANT
2 AWAY
5 TEST
8 CODE
PAGE
READY
0
3 STAY
6 BYPASS
9 CHIME
#
FA 5 6 0
8VHU*XLGH
K0736-1V1 10/03 Rev. B
IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible
point of entry to a home or commercial premises. This would include any
skylights that may be present, and the upper windows in a multi-level building.
In addition, we recommend that radio backup be used in a security system so
that alarm signals can still be sent to the Central Monitoring Station in the event
that the telephone lines are out of order (alarm signals are normally sent over
the phone lines).
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors
have played a key role in reducing fire deaths in the United States. With regard
to the number and placement of smoke/heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Association's
National Fire Alarm Code (NFPA 72). These recommendations can be found on
page 43 of this manual.
$ERXW7KLV0DQXDO
This manual is a step-by-step guide that will acquaint you with the system's
features and benefits. It defines the components and their functions, describes
their operation, and provides clear step-by-step instructions for normal and
emergency procedures. Keep this manual in a convenient place so that you can
refer to it as necessary.
–2–
7DEOHRI&RQWHQWV
System Overview .................................................................................................................... 5
Introduction .......................................................................................................................... 5
System Basics ....................................................................................................................... 5
Using the Voice Message Center ......................................................................................... 7
About The Keypads ................................................................................................................ 8
General Information............................................................................................................. 8
Functions of the Keypads................................................................................................... 10
Entry/Exit Delays ................................................................................................................. 12
Exit Delay............................................................................................................................ 12
Entry Delay ......................................................................................................................... 12
Exit Alarms ......................................................................................................................... 13
Checking For Open Zones .................................................................................................. 14
Using the [∗] Key ................................................................................................................ 14
Arming the System............................................................................................................... 15
Stay Mode: Arms Perimeter Only, Entry Delay On ......................................................... 15
Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones ....................................... 15
Instant Mode: Arms Perimeter Only, Entry Delay Off .................................................... 15
Away Mode: Arms Entire System, Entry Delay On ......................................................... 15
Maximum Mode: Arms Entire System, Entry Delay Off ................................................. 15
Arming Commands............................................................................................................. 16
Single Button Arming ........................................................................................................ 17
Step Arming Feature.......................................................................................................... 17
Using the Keyswitch ............................................................................................................ 18
Using the Keyswitch........................................................................................................... 18
Disarming and Silencing Alarms ..................................................................................... 19
Using the [OFF] key ........................................................................................................... 19
Bypassing Protection Zones .............................................................................................. 20
Using the BYPASS Key...................................................................................................... 20
Quick Bypass ...................................................................................................................... 21
Chime Mode ........................................................................................................................... 22
Date and Time ....................................................................................................................... 23
Viewing the Current Date and Time................................................................................. 23
Setting the Date and Time................................................................................................. 23
–3–
Table of C ontents
Panic Keys.............................................................................................................................. 24
Using Panic Keys................................................................................................................ 24
Macro Key Programming & Usage................................................................................... 25
About Macro Keys............................................................................................................... 25
Example of Macro Programming ....................................................................................... 26
Using a Programmed Macro Key....................................................................................... 26
Using Device Commands .................................................................................................... 27
About Device Commands ................................................................................................... 27
Paging Feature ..................................................................................................................... 28
About Automatic Paging .................................................................................................... 28
Manual Paging.................................................................................................................... 29
Latch Key Paging ............................................................................................................... 29
Security Codes & Authority Levels.................................................................................. 30
About Security Codes ......................................................................................................... 30
Authority Level Definitions ............................................................................................... 30
How to Assign User Codes and Attributes........................................................................ 31
Scheduling ............................................................................................................................. 32
About Scheduling................................................................................................................ 32
Creating Schedules............................................................................................................. 32
Event Logging Procedures................................................................................................. 34
About Event Logging .......................................................................................................... 34
Viewing the Event Log ....................................................................................................... 34
Table of Event Log Codes................................................................................................... 35
Testing the System (To Be Conducted Weekly) ............................................................ 36
About Testing the System .................................................................................................. 36
Trouble Conditions .............................................................................................................. 37
Maintaining Your System................................................................................................... 40
Fire Alarm System (If Installed)....................................................................................... 41
Quick Guide to Basic System Functions ........................................................................ 45
Summary of Audible/Visual Notifications...................................................................... 46
Regulatory Statements and Warnings ............................................................................ 48
Charts of Your System’s Features .................................................................................... 49
–4–
6\VWHP2YHUYLHZ
,QWURGXFWLRQ
Congratulations on your ownership of the First Alert Professional Security System.
You've made a wise decision in choosing it, for it represents the latest in security
protection technology today. This system provides:
• Three forms of protection: burglary, fire* and emergency
• At least one keypad which provides control of system and displays system status
• Various sensors for perimeter and interior burglary protection
• Smoke or combustion detectors* designed to provide early warning in case of fire.
Your system may also have been programmed to automatically send alarm or status
messages over the phone lines to a Central Monitoring Station.
* Commercial installations and some residential systems may not include fire
protection – check with your installer.
6\VWHP%DVLFV
Burglary Protection
• Several modes of burglary protection: Stay, Night-Stay, Away, Instant, Maximum.
STAY: arms perimeter zones only and entry delay is on
INSTANT: same as STAY, except entry delay is off
NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on
AWAY: arms perimeter and all interior zones, entry delay is on
MAXIMUM: same as AWAY, except entry delay is off
• You can BYPASS selected zones while leaving the rest of the system armed.
• CHIME mode alerts you to the opening of protected doors and windows while the
system is disarmed.
Fire Protection
• Fire protection is always active (if installed) and an alarm sounds if a fire
condition is detected
• If necessary, you can manually initiate a fire alarm using the keypad (if
programmed).
• Refer to the Fire Alarm System section for information regarding fire protection,
smoke detectors and planning emergency exit routes.
Security Codes
• You were assigned a 4-digit security code during system installation.
• Use your security code when arming and disarming the system, and when
performing other system functions.
• Other users can be assigned different security codes, each with different
authority levels, which define the system functions a particular user can perform.
–5–
6\VWHP2YHUYLHZ&RQWLQXHG
Zones
• The system sensing devices have been assigned to various “zones,” which are
specific areas of protection (e.g., front door, kitchen window, etc.).
• Zone numbers are displayed at the keypad when an alarm or trouble condition
occurs on a sensor.
Arming, Step-Arming and Disarming Burglary Protection
• The system must be armed before the burglary protection can sense intrusions.
• To arm your system, enter your user code followed by the desired arming key.
• If programmed, the [#] key can be pressed instead of entering the security code
when arming the system.
• You can also use the step-arming key, if programmed, to arm the system, which
lets you use a function key to arm the system in one of three modes by simply
pressing the key repeatedly.
• To disarm the system, enter your user code then press the [OFF] key.
Alarms
• When an alarm occurs, both the keypad and external sounders will sound, and
the keypad will display the zone(s) causing the alarm.
• If your system is connected to a Central Monitoring Station, an alarm message
will also be sent.
• To stop the alarm sounding, simply disarm the system.
Memory of Alarm
• When an alarm condition occurs, the keypad displays the number(s) of the
zone(s) that caused the problem, and displays the type of alarm (e.g., “fire”).
• The message remains displayed even after disarming the system, but can be
cleared with another “off” sequence.
Phone Access
• If included, a phone module permits you to access the system via a touch-tone
phone, either on-premises or by calling-in when away.
• You can receive synthesized voice messages over the telephone regarding the
status of the security system.
• You can arm and disarm the system and perform most function commands
remotely via the telephone, with voice confirmation provided after each command
entry.
• Complete information regarding the use of this feature is provided in a separate
manual entitled “Phone Access User's Guide” that is supplied with the voice
module.
–6–
6\VWHP2YHUYLHZ&RQWLQXHG
Paging Feature
• If programmed, the system can automatically send certain system condition
messages to a pager.
• The display consists of code numbers that indicate the type of condition that has
occurred.
Function Keys
• The “A”, “B”, “C”, and “D” keys on the keypad can be programmed to perform
various functions.
• Functions include: activate a Panic alarm; arm the system; provide step arming;
switch lights on/off; send a message to a pager; display Time/Date; start a Macro
Scheduling
• Your system can be programmed to automatically perform certain functions (e.g.,
arm the system) at a predetermined time each day.
8VLQJWKH9RLFH0HVVDJH&HQWHULI9RLFH.H\SDGLVLQVWDOOHG
LEDS
The Voice Keypads feature a voice message center
that lets you record and playback one message.
LCD
DISPLAY
• The message can be up to 2.5-minutes long
• The message remains in the keypad’s memory
until a new message is recorded.
ARMED
MESSAGE
VOLUME
KEY
RECORD
KEY
• The volume control of the message is adjustable.
• Refer to the procedures below when using the
Message Center functions.
READY
SPEAKER
FUNCTION
KEYS
PLAY KEY
AND
UP VOLUME
A
1 OFF
RECORD
VOLUME
B
4 MAX
5 TEST
6BYPASS
C
7
8
9 CHIME
D
*
INSTANT
READY
STATUS
2 AWAY
CODE
0
VOICE
3 STAY
PLAY
FUNCTION
FA560
STATUS
KEY
MICROPHONE
DOWN
VOLUME
#
VOICE
KEY
FUNCTION
KEY
FA560VKP-004-V0
Message Center Functions
To…
record a
message
end
recording
play a
message
adjust the
volume
Press these keys…
Notes…
The
red MESSAGE LED lights.
[#] FUNCTION + [0] VOICE + [1] RECORD
Message remains in memory
until a new message is recorded.
The red MESSAGE LED flashes,
[1] RECORD
indicating message waiting.
The recorded message plays and
[#] FUNCTION + [0] VOICE + [3] PLAY
the red MESSAGE LED turns off.
[#] FUNCTION + [0] VOICE + [2] VOLUME keys, Adjusting message volume also
adjusts status volume. Volume
then press volume key [3] ↑ (up) or [6] ↓ (down)
cannot be adjusted while playing.
–7–
$ERXW7KH.H\SDGV
*HQHUDO,QIRUPDWLRQ
Your keypads allow you to control all system functions. The keypads feature the
following:
• A telephone style (digital) keypad
• Liquid Crystal Display (LCD) which shows the nature and location of all
occurrences
• Built-in sounder which will sound during alarms and troubles. The sounder also
"beeps" during certain system functions and when depressing any of the keys (to
acknowledge the key press).
• Backlighting of the LCD display windows. Backlighting turns on when any key is
pressed, and when opening an entry/exit door while the system is armed. This
feature is helpful when a keypad is located in a dimly lit area.
IMPORTANT: If the keypad beeps rapidly upon entering the premises, it indicates
that an alarm has occurred during your absence and an intruder may still be on the
premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe
location.
Your keypads are functionally the same, but may have different types of displays,
depending on the type installed with your system.
Alpha Display
2-line alpha display keypads feature a 2-line, 32-character
alphanumeric LCD which can display system messages in
friendly English. These keypads can also be programmed with
custom zone descriptors.
Fixed-Word Display Fixed-Word display keypads are functionally identical to Alpha
display keypads, but the LCD display uses pre-designated
words to identify the nature and location of occurrences.
Voice Keypads
–8–
Voice Keypads (if installed), are functionally the same as other
keypads, except that these keypads can provide the following:
• Voice announcements of system status (see Checking for
Open Zones section)
• Voice chime, which can alert you to the opening of doors and
windows while the system is disarmed (see Voice Chime in
Chime mode section)
• Message center, which lets you record and playback
messages (see Using the Voice Message Center in the
System Overview section).
$ERXW7KH.H\SDGV&RQWLQXHG
)L[HG:RUG'LVSOD\.H\SDG
AWAY:
STAY:
INSTANT:
BYPASS:
All burglary zones, interior and
perimeter, are armed.
Perimeter burglary zones, such as
protected windows and doors, are
armed.
Entry delay is turned off:
Lit with STAY = Instant mode
Lit with AWAY = Maximum mode
This appears when one or more
burglary protection zones have been
bypassed.
AWAY
NIGHT NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT CANCELED
BYPASS
ALARM STAY
FIRE CHECK
6150disp
FA260KP
00
AWAY
NO AC
STAY
CHIME
BAT
ALARM INSTANT
CHECK BYPASS CANCELED
NOT READY
FIRE NIGHT
FA215KP
FIXED-WORD DISPLAYS
NOT READY:
NO AC:
AC:
CHIME:
BAT:
ALARM:
CHECK:
FIRE:
NIGHT:
CANCELED:
Appears when burglary portion of the system is not ready for arming
(due to open protection zones). The system is ready to arm when this
message disappears and the READY indicator light comes on.
Appears when AC power has been cut off. System is operating on
backup battery power.
Appears when AC power is present.
Appears when the CHIME feature is activated.
Low battery condition in a wireless sensor (if zone number displayed)
or low system battery (if no zone number displayed).
Appears when an intrusion has been detected and the system is armed
(also appears during a fire alarm or audible emergency alarm).
Accompanied by the protection zone in alarm.
Appears when a malfunction is discovered in the system at any time or
if an open is detected in a FIRE zone at any time or a fault in a
DAY/NIGHT burglary zone during a disarmed period. Accompanied by
a display of zone number in trouble.
Appears when a fire alarm is present. Accompanied by a display of the
zone in alarm.
A FIRE display also appears when a fire alarm is manually activated,
accompanied by a display of emergency key zone number programmed
for fire.
Appears with “STAY” when the system is armed in Night-Stay mode
(perimeter burglary zones and pre-selected interior zones are armed).
Appears when an alarm has been canceled (see Exit Alarm section for
more information on canceled alarms and displays).
–9–
)XQFWLRQVRIWKH.H\SDGV
NOTE: The functions printed directly on the
keys indicate their primary purpose; the
functions printed under some of the keys
(shown in brackets under the respective key),
indicate their alternate or secondary purpose.
DISPLAY WINDOW
Alpha Display Keypads:
2-line, 32-character
Liquid Crystal Display (LCD) keypads that display
protection points, system status, and messages.
Fixed-Word Display Keypads: Display
protection zone ID and system status messages using
pre-designated words in the LCD display area.
[VOICE] On Voice keypads, enables the RECORD,
VOLUME and PLAY functions.
Disarms burglary portion of the system,
silences alarms and audible trouble indicators, and
clears visual display after problem's correction.
[RECORD] On Voice keypads, used in conjunction
with the FUNCTION and VOICE keys to record up
to a 2.5-minute message.
2 AWAY
Arms the entire burglary system,
perimeter and interior.
[VOLUME] On Voice keypads, used in conjunction
with the FUNCTION and desired volume control
keys ↑ [3] or ↓ [6] to adjust the volume of a recorded
message or voice system status.
3 STAY
Arms perimeter portion of burglary
system only. Interior protection is not armed,
allowing movement within premises without causing
an alarm. If pressed twice in succession, arms
system in Night-Stay mode.
[PLAY] On Voice keypads, used in conjunction with
the FUNCTION and VOICE keys to play the
recorded message.
[ ↑ ] On Voice keypads, used in conjunction with the
FUNCTION and VOLUME keys to raise the
message and voice system status volume.
4 MAXIMUM
Arms the entire burglary system,
perimeter and interior, but without entry delay.
Entering via an entry/exit door will cause an alarm.
5 TEST
Tests the system and alarm sounder if
disarmed. Refer to Testing The System section for
test procedures.
– 10 –
7 INSTANT Arms in manner similar to the STAY
mode, but without the entry delay feature.
8 CODE
Used to assign additional user codes and
attributes for other users of the system.
9 CHIME
Turns CHIME mode on and off. When on, the
opening of windows or doors while the system is disarmed
sounds 3 beeps at the keypad(s).
0
1 OFF
6 BYPASS Removes individual protection zones from
being monitored by the system.
[ ↓ ] On Voice keypads, used in conjunction with the
FUNCTION and VOLUME keys to lower the message
and voice system status volume.
KEYS 0–9: Used to enter your security code(s) and to
perform their associated system functions after the
security code has been entered.
∗ READY Used to display all open protection zones.
[STATUS]: On Voice keypads, a momentary press of the
STATUS key annunciates the current system status.
Pressing the STATUS key a second time annunciates and
displays system and/or zone faults (if they exist).
#
This key can be used for "Quick Arming" of
the system without use of a security code (if
programmed).
[FUNCTION] On Voice keypads, enables the desired
voice or volume function.
FUNCTION KEYS: Keys A, B, C, D may have been
programmed for a variety of functions, including panic
(emergency) functions. For details, see the Function Keys
section.
ARMED LED INDICATOR: (RED) Lit when the
system has been armed.
READY LED INDICATOR: (GREEN) Lit when the
system is ready to be armed (no faults present). While the
system is disarmed, this indicator will go on and off as
protection zones are closed and opened.
MESSAGE LED INDICATOR: (RED) On Voice
keypads, flashes red when message waiting or lights red
(steady) when in record mode.
MIC: On voice keypads, microphone for Message Center
recordings.
INTERNAL SPEAKER: The built-in speaker mimics
the alarm sounder during alarms, and will also "beep"
during certain system functions. The speaker also
provides voice playback for any recorded messages.
)XQFWLRQVRIWKH.H\SDGV&RQWLQXHG
LEDS
LCD
DISPLAY
ARMED
READY
MESSAGE
SPEAKER
A
FUNCTION
KEYS
1 OFF
2 AWAY
RECORD
VOLUME
B
4 MAX
5 TEST
6BYPASS
C
7INSTANT
8 CODE
9 CHIME
D
*
0
#
READY
STATUS
VOICE
3 STAY
PLAY
FUNCTION
FA560
MICROPHONE
FA560VKP-003-V0
Voice-capable 2-line Alpha keypad
IMPORTANT!
• When entering codes and commands, sequential key depressions must be made
within 4-5 seconds of one another. If 4-5 seconds elapse without a key depression, the
entry will be aborted and must be repeated from its beginning. Be sure to observe
this precaution when performing any of the procedures in this manual.
• If you make a mistake while entering a security code, stop, press the [✱] key, and
then start over. If you stop in the middle while entering a code, and then
immediately start the entry over, an erroneous code might be entered.
– 11 –
(QWU\([LW'HOD\V
Your system has preset time delays, known as exit delay and entry delay.
([LW'HOD\
Exit delay gives you time to leave through the designated exit door(s) without
setting off an alarm. Exit delay begins immediately after arming your system in any
arming mode and Alpha Display keypads display the message “You May Exit Now.”
When “You may exit now” disappears, the system is fully armed. If programmed, a
slow beeping will sound during the exit delay period until the last 10 seconds, which
then changes to fast beeping (alerting you to the end of exit delay). If you cannot
leave by this time, you should stop, disarm the system, and start over to avoid a false
alarm.
Exit Delay Restart/Reset. If you wish to open the entry/exit door to let someone in
after arming STAY, you can re-start the exit delay at any time – simply press the
[✱] key, then let that person in. The system automatically re-arms when exit delay
expires, which avoids having to disarm the system and then re-arm it again.
In addition, when the system is armed AWAY, reopening and closing the entry/exit
door before exit delay time expires (e.g., reentering to get a forgotten item) will reset
the exit delay time once.
(QWU\'HOD\
Entry Delays give you time to disarm the system when you re-enter through the
designated entrance door. There are two entry delays (if programmed). The first is for
your primary entrance and the second can be used for a secondary entrance, where a
longer delay is required to walk to the keypad to disarm the system.
You must disarm the system before the entry delay period ends, or an alarm will
occur. The keypad beeps during the entry delay period, reminding you to disarm the
system. The beeps stop when a code is entered, but will restart after about 10 seconds
if an invalid code is entered.
You can also arm the system with no entry delay at all by using the INSTANT or
MAXIMUM arming mode. This mode provides greater security while on the
premises or while away for extended periods of time.
See your installer for your delay times.
Exit Delay:
– 12 –
seconds
Entry Delay 1:
seconds
Entry Delay 2:
seconds
(QWU\([LW'HOD\V&RQWLQXHG
([LW$ODUPV
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior
zone is faulted within two minutes after the end of the exit delay (e.g., exit door left
open), the system sounds an alarm and starts the entry delay timer. If you disarm the
system before the entry delay ends, the alarm sound stops and the message
"CANCELED ALARM" or "CA" is displayed on the keypad, along with a zone number
indicating the faulted zone. No message is sent to the Central Monitoring Station.
To clear the exit alarm condition, the open zone must be made intact; to clear the
display, enter your code plus OFF.
If you do not disarm the system before the entry delay ends, and an entry/exit door or
interior zone is still open, the alarm sound continues and an "exit alarm" message is
sent to the Central Monitoring Station. The message ""EXIT ALARM" or "EA" is
displayed on the keypad, along with a zone number indicating the faulted zone. To
stop the alarm, the system must be disarmed (your code plus OFF); to clear the
display, enter your code plus OFF a second time.
Your system may have been programmed for this feature to minimize false alarms sent to the Central
Monitoring Station. Ask your installer if "Exit Alarm" is active in your system. If so, check this box.
– 13 –
&KHFNLQJ)RU2SHQ=RQHV
8VLQJWKH>∗@.H\
Before arming your system, all protected doors, windows and other protection zones
must be closed or bypassed, otherwise the keypad will display a "Not Ready" message.
1. Press [∗] READY (do not enter code first) to display
faulted zones.
2. Secure or bypass the zones displayed.
3. The keypad’s READY indicator lights when all
protection zones have been either closed or bypassed.
4. Arm the system as desired.
Alpha Display:
(-7%61)( 46)77
∗
83 7,3; *%9087
Fixed-Word Display:
Zone no. and “NOT READY”
Voice Status: Voice Keypads (if installed), can announce system status and faulted
zones (up to 3 zone descriptors) if the Voice Status feature is turned on.
To turn the Voice Status feature on/off: # + 0
+
2
+
4
(also turns on Voice Chime mode; see Chime mode section)
To announce Status: Press [#] FUNCTION + [0] VOICE + [∗] STATUS key.
(Announces current system status; e.g., “Disarmed Ready to
Arm.”)
To announce faults:
– 14 –
Press [#] FUNCTION + [0] VOICE + [∗] STATUS + [∗] again
within 5 seconds of the first press. (Announces up to three
faulted zones with their zone descriptors, if programmed.)
$UPLQJWKH6\VWHP
6WD\0RGH$UPV3HULPHWHU2QO\(QWU\'HOD\2Q
• Used when you want to arm the system with persons staying inside (or if you have
pets that are moving throughout the premises).
• The perimeter sensors are armed, but interior sensors are left disarmed.
• Exit delay begins (you can leave through the entry/exit door, if desired).
• An alarm sounds if any protected window or non-entry/exit door is opened.
• You may otherwise move freely within the premises.
• Persons entering later can enter through an entry/exit door, but they must disarm
the system within the entry delay period to avoid sounding an alarm.
1LJKW6WD\0RGH$UPV3HULPHWHU2QO\3OXV6HOHFWHG=RQHV
• Use Night-Stay mode to provide increased security while staying inside.
• Arms same as Stay mode, but also arms pre-selected interior sensors (programmed
by your installer), while other interior sensors are left disarmed.
• Persons entering later can enter through an entry/exit door but they must disarm
the system and must not violate any of the programmed interior zones to avoid
sounding an alarm.
• IMPORTANT: When Night-Stay mode is on, the selected interior zones are armed and cause an
alarm if anyone enters those areas (e.g., waking in the middle of the night). To avoid sounding an
alarm, you must disarm the system before any activity takes place in those interior zones.
,QVWDQW0RGH$UPV3HULPHWHU2QO\(QWU\'HOD\2II
• Used when staying inside and do not expect anyone to use an entry/exit door.
• Arms same as Stay mode.
• An alarm sounds immediately if any protected perimeter window or any door is
opened, including entry/exit doors.
• IMPORTANT: Arming in this mode greatly increases the chance of false alarms. Use extreme
care in selecting this mode of arming.
$ZD\0RGH$UPV(QWLUH6\VWHP(QWU\'HOD\2Q
•
•
•
•
Used when nobody will be staying inside (including pets).
The entire system (interior and perimeter) is armed.
Exit delay begins letting you leave through the entry/exit door.
An alarm sounds if a protected window or any door is opened, or if any movement
is detected inside your premises.
• You can reenter through an entry/exit door, but you must disarm the system within
the entry delay period to avoid sounding an alarm.
0D[LPXP0RGH$UPV(QWLUH6\VWHP(QWU\'HOD\2II
• Used when leaving the premises for extended periods (e.g., vacation).
• Arms same as Away mode, but entry delay is off.
• An alarm sounds same as Away mode, and sounds upon opening entry/exit doors.
– 15 –
$UPLQJWKH6\VWHP
$UPLQJ&RPPDQGV
Before arming, close all perimeter doors and windows and make sure the Ready to Arm
message is displayed.
Modes of Arming
Mode
Press these keys…
Stay
security code + [3] (STAY)
Night-Stay
security code + [3] + [3]
Instant
security code + [7] (INSTANT)
Away
security code + [2] (AWAY)
Maximum
security code + [4] (MAXIMUM)
Keypad Confirms By…
• three beeps†
• armed STAY message displayed
• red ARMED indicator lights
• three beeps†
• NIGHT-STAY message displayed
• red ARMED indicator lights
• three beeps†
• armed STAY message displayed
• red ARMED indicator lights
• also note that entry delay is turned off.
• two beeps†, or, if programmed, beeping for
duration of exit delay
• armed AWAY message displayed
• red ARMED indicator lights
Leave the premises through an entry/exit
door during the exit delay period to avoid
causing an alarm. The keypad beeps rapidly
during the last 10 seconds of the exit delay
to warn you that it is ending.
• same as Away (described above)
Note that entry delay is turned off.
† Arming Ding: In addition to the keypad beeps, the external sounder emits a short “ding” sound after
arming, if programmed to do so. The ding confirms that the system is armed, and may occur immediately
after the command or be delayed (until arm/disarm report is sent or exit delay expires). Ask your installer
about how this feature is set for your system.
Quick Arming
If "Quick Arming" was programmed by the installer, the [#] key can be pressed in
place of the security code when arming the system in any of its arming modes (except
Night-Stay). However, the security code must always be used to disarm the
system.
Function Key Arming
For any arming command, a function key may have also been programmed for your
system. If so, you can press and hold the appropriate function key for 2 seconds to arm
the system. See your installer for the designated functions (see Single Button
Arming section).
– 16 –
$UPLQJWKH6\VWHP
6LQJOH%XWWRQ$UPLQJ
The “A”, “B”, “C”, and/or “D” keys on your keypad may have been programmed for
single-button arming. Note that while it will not be necessary to use a security code
for arming, a security code must always be used to disarm the system.
If Single-Button Arming is programmed:
• A function key has been assigned to a specific type of arming: STAY mode,
Night-STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming
paragraph).
• You DO NOT need to enter your security code before pressing the function key
(but you always need your security code to DISARM the system).
Before arming, close all perimeter doors and windows.
1. Press and hold the assigned function key for 2
seconds (no code is required). Function keys are
shown below.
Alpha Display:
(-7%61)(
6)%(= 83 %61
Fixed-Word Display: READY
2. The keypad begins beeping and displays the armed
message. The red ARMED indicator also lights.
Alpha Display:
%61)(%;%=
=39 1%= )<-8 23;
Fixed-Word Display: AWAY
6WHS$UPLQJ)HDWXUH
Single-Button “Step” arming may have been programmed into one of the lettered keys
(A, B, C, or D). Check with your installer to see if this has been done in your system.
If Step-Arming is programmed:
• The assigned key provides a choice of three levels of security.
• The selected key can be pressed once, twice, or three times, increasing the level
of security with each press, as follows
Key
First Press
Second Press
Third Press
Ø
Ø
Ø
Ø
A, B, C, D
Armed-STAY
Armed Night-STAY
(if programmed)
Armed-AWAY
– 17 –
8VLQJWKH.H\VZLWFK
8VLQJWKH.H\VZLWFK
Your system may be equipped with a keyswitch for use when arming and disarming.
Red and green lights on the keyswitch plate indicate the status of your system as
follows:
Green Light: Lights when the system is disarmed and ready to be armed (no
open zones). If the system is disarmed and the green light is off, it
indicates the system is not ready (one or more zones are open).
Red Light:
Lights or flashes when system is armed in AWAY or STAY mode.
See your installer for the meanings of the lit red light:
Lit Steady = system armed AWAY or
system armed STAY and exit delay has expired
Flashing
= system armed STAY and exit delay timer active
Rapid flashing = an alarm has occurred (memory of alarm).
Before arming, close all perimeter doors and windows.
To arm in the AWAY mode:
Turn the key to the right for 1/2 second and release.
Keypads beep twice and the red indicator lights or
flashes.
To arm in the STAY mode:
Turn the key to the right and hold for longer than 1
second, then release. Keypads beep three times and
the red indicator lights or flashes.
To disarm the system:
Turn the key to the right and release. The red light
turns off
– 18 –
GREEN
RED
'LVDUPLQJDQG6LOHQFLQJ$ODUPV
8VLQJWKH>2))@NH\
The OFF key is used to disarm the system, silence alarm and trouble sounds, and
clear alarm memories.
IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but
CONTACT THE POLICE from a nearby safe location.
If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will
beep rapidly upon your entering, indicating that an alarm has occurred during your
absence.
LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.
+
1.
(Security Code)
1
OFF
The “READY” indicator light will be lit if all zones
are secure, and the keypad will emit a single tone to
confirm that the system is disarmed.
Alpha Display:
(-7%61)(
6)%(= 83 %61
Fixed-Word Display: READY
NOTE: If entry delay has started (you’ve opened the
entry door), you do not need to press the OFF key;
simply enter your security code. The system will
disarm in about 10 seconds after the last digit of the
code is entered.
2. To Silence a Burglary Alarm and Clear a Memory of Alarm
Enter your security code. This disarms the system and silences the alarm (or
warning tones of a Memory of Alarm).
Note the zone in alarm on the keypad display, and make that zone intact (close
door, window, etc.). Now enter the security code plus OFF to clear the keypad’s
Memory of Alarm display.
3. To Silence a Fire Alarm and Clear Memory of Alarm
Simply press the OFF key to silence the alarm. Then enter the security code plus
OFF sequence to clear the keypad's Memory of Alarm display. See the Fire Alarm
System section.
– 19 –
%\SDVVLQJ3URWHFWLRQ=RQHV
8VLQJWKH%<3$66.H\
Use this key when you want to arm your system with one or more zones intentionally
unprotected.
Vent Zones: Your system may have certain windows set as “vent” zones, which are
automatically bypassed if left open when arming the system (you do not need to
manually bypass them). However, if a vent zone window is closed after arming, it
becomes protected and will cause an alarm if opened again while the system is armed.
When bypassing zones:
• The system must be disarmed before you can bypass zones.
• Bypassed zones are unprotected and will not cause an alarm if violated.
• The system will not allow fire zones to be bypassed.
• Zones are automatically unbypassed when the system is disarmed.
+
1.
(Security Code)
6 + zone numbers (see below)
BYPASS
Enter the 2-digit zone number(s) for the zone(s) to be
bypassed (e.g., 06, 10, 13, etc.). Single digit zone
numbers must be preceded by a zero (e.g. 05, 06).
2. When finished, the keypad will momentarily display
a "Bypass" message for each bypassed zone number.
Wait for all bypassed zones to be displayed.
Arm the system as usual. When armed, the arming
message is displayed with “ZONE BYPASSED.”
To display bypassed zones prior to arming, enter
your security code and press the [6] BYPASS key.
Alpha Display:
(-7%61)( 46)77
83 7,3; *%9087
Fixed-Word Display: NOT READY
Alpha Display:
(-7%61)( &=4%77
6)%(= 83 %61
Fixed-Word Display: BYPASS
%61)( 78%=
>32) &=4%77)(
Typical armed alpha display after
bypassing zones.
– 20 –
%\SDVVLQJ3URWHFWLRQ=RQHV
4XLFN%\SDVV
If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones
without having to enter zone numbers individually. This feature is useful if, for
example, you routinely leave certain windows open when arming at night.
1.
+ 6 + [#]
Alpha Display:
(Security Code) BYPASS
(-7%61)( 46)77
In a few moments, all open zones will be displayed
and automatically bypassed. Make sure that only
those zones that you wish to leave unprotected are
bypassed, and that there are no other zones
unintentionally left open.
83 7,3; *%9087
2. Wait for all bypassed zones to be displayed, then arm
the system as desired.
Ask your installer if "Quick Bypass" is active for your
system, and if so, check here:
Fixed-Word Display: NOT READY
(-7%61)( &=4%77
6)%(= 83 %61
Fixed-Word Display: BYPASS
– 21 –
&KLPH0RGH
CHIME mode alerts you to the opening of a perimeter door or window while the
system is disarmed. When Chime mode is activated:
• Three tones sound at the keypad whenever a perimeter door or window is opened.
• Interior zones do not produce a tone when they are faulted.
• Pressing the READY key will display the open protection points.
• Chime mode can be used only while the system is disarmed.
To turn Chime Mode on/off (system must be disarmed):
+
(Security Code)
(-7%61)( ',-1)
9
6)%(= 83 %61
CHIME
Fixed-Word Display: CHIME
The CHIME message appears when on. Perimeter
zones will cause a tone when faulted.
The CHIME message disappears when Chime mode is off.
Voice Chime: You can set the Voice Keypads (if installed) to announce faulted
(opened) entry/exit or perimeter zones whenever normal Chime mode is on.
To turn Voice Chime Mode on or off: # + 0
+
2
+
4
(normal Chime mode must be on first)
When Voice Chime is on, faulted zones cause a voice status announcement, chime
and display. When off, the sounder still provides chime if normal Chime mode is on.
– 22 –
'DWHDQG7LPH
9LHZLQJWKH&XUUHQW'DWHDQG7LPH
The system lets you view its time and date setting on alpha keypad.
Alpha Display:
+[#] + [6] [3]
(-7%61)(
(Security Code)
OR, press the function key (A, B, C, or D) for viewing
current date and time, if programmed.
A typical time/date display is shown.
The display will remain on for about 30 seconds.
“A ”
“B”
“C ”
6)%(= 83 %61
8-1)(%8)
7%8
%1C
“D ”
If one of the above keys has been programmed for the date/time
display feature, place a check mark in the box beneath that key.
6HWWLQJWKH'DWHDQG7LPH
You can set the time and date by doing the following:
+[#] + [6] [3]
1.
(Security Code)
Alpha Display:
(-7%61)(
6)%(= 83 %61
2. Press [∗] when the time/date is displayed.
A cursor appears under the first digit of the hour.
To move cursor ahead, press [∗]. To go back, press [#].
• Enter the 2-digit hour setting.
• Enter the 2-digit minute setting.
• Press [1] for PM or [0] for AM.
• Enter the last two digits of the current year.
• Enter the 2-digit month setting.
• Enter the 2-digit day setting.
3. To exit, press [∗] when cursor is at the last digit, or
wait 10 seconds.
8-1)(%8)
7%8
41 Current time display
8-1)(%8)
7%8
4
Time/date editing display
– 23 –
3DQLF.H\V
8VLQJ3DQLF.H\V
Your system may have been programmed to use special keys to manually activate
emergency (panic) functions as follows:
This Function
Silent Alarm
Sends this signal* With This Sounding…
silent alarm
no audible alarm and no change in
normal display to indicate that a silent
alarm has been initiated.
Audible Alarm
audible alarm
a loud, steady alarm at keypad(s) and at
any external sounders that may be
connected.
Personal Emergency auxiliary alarm
steady alarm sound at keypad(s), but not
at external bells or sirens.
Fire Alarm
fire alarm
temporal (pulsing) sound at external
bells and sirens.
*All panic functions send signals to the Central Monitoring Station, if connected.
To activate a Panic Function:
Press and hold down for at least 2 seconds whichever
lettered key on the keypad has been programmed for
the desired emergency function.
Alpha Display:
(-7%61)(
6)%(= 83 %61
Fixed-Word Display: READY
OR
Press both keys of the assigned key pair at the same
time.
Typical Panic Alpha Display:
%0%61 Fixed-Word Display: 99 and ALARM
ZONE 95
ARMED
READY
PRESS BOTH KEYS
OF DESIRED PAIR
AT THE SAME TIME
READY
R
B
ZONE 99
AWAY
1 OFF
2 AWAY
3 STAY
STAY
4 MAX
5 TEST
6 BYPASS
7INSTANT
8 CODE
9 CHIME
0
#
ZONE 95
R
AWAY
1 OFF
2 AWAY
3 STAY
STAY
4 MAX
5 TEST
6 BYPASS
ZONE 96
7INSTANT
PAGE
D
READY
8 CODE
9 CHIME
0
#
FA 5 6 0
560KP-10-001-V0
PAGE
C
Lettered Panic Keys
READY
FA 5 6 0
ZONE
99
ZONE 96
560KP-10-002-V0
ARMED
A
Panic Key Pairs
See your installer and use the chart provided in the Features Programmed in Your
System section to note the functions that have been programmed for your system.
– 24 –
0DFUR.H\3URJUDPPLQJ8VDJH
$ERXW0DFUR.H\V
The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of
commands of up to 16 keystrokes, if programmed for this function. These keystrokes,
as a group, are called “macros” and are stored in the system's memory.
• Typical macro functions can include:
- Arming sequences: STAY, Night-STAY, INSTANT, or AWAY
- Bypassing particular zone(s)
- Activating relay(s) for turning on (or off) lights, fans, etc.
• One macro can be assigned.
• Macros can be activated only by users with authority levels authorized to
perform the macro’s function.
NOTE: The installer must activate the desired function key before macros can be
assigned. See the chart at the back of this manual for the key(s) assigned for macros.
1.
+ [#] + [6] + [6]
(Security Code)
Alpha Displays:
(-7%61)(
6)%(= 83 %61
If a macro has been previously defined, the
keystrokes are shown on the bottom line of the
display, otherwise the display is blank.
1%'63 (-740%=
To exit this mode (and keep the existing macro
definition), press any key except the [∗] key. The
system returns to normal mode.
To define a macro for the selected key, press [∗] and
continue with the next prompt.
2. Enter the first of the series of desired commands, (do
not include your user code), then press/hold the “D”
key for at least two seconds to complete the first
command. This key terminates each command, and
appears as an “F” in the keypad display.
1%'63 4+1
– 25 –
0DFUR.H\3URJUDPPLQJ8VDJHFRQW
The keypad beeps to acknowledge your input and
displays the command you entered (followed by “F”).
4. Enter the next command, followed by press/holding
the “D” key for at least two seconds. The keypad
beeps and displays the keystrokes entered so far.
5. Repeat until the all the desired commands (up to 16
characters including the “F”s) have been entered.
Be sure to check your keystrokes before continuing.
If you made a mistake, you must start over.
6. To exit, press/hold the “D” key for at least two
seconds. The display returns to system status and
indicates system is ready.
Typical Macro Alpha Display:
1%'63 4+1
*#**
([DPSOHRI0DFUR3URJUDPPLQJ
Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an
exterior light, and then (3) arm the security system in the AWAY mode. The
procedures in the table that follows show you how you would program this macro:
Function
Keystrokes Required
Keypad Display
1. Bypass zones 02 & 03
2. Insert terminator.
Press BYPASS [6] key, then
2-digit zone numbers 02 & 03.
Press the “D” key for at least 2 seconds.
3. Turn light on
(device 01).
4. Insert terminator.
Press [#] and 7 keys for “device ON”, and
[01] key for selecting device 1.
Press the “D” key for at least 2 seconds.
5. Arm system AWAY
Press AWAY [2] key.
6. Insert terminator.
Press the “D” key for at least 2 seconds.
*
*#
*#*
*#*
*#**
8VLQJD3URJUDPPHG0DFUR.H\
(-7%61)(
6)%(= 83 %61
)28)6 97)6 '3()
– 26 –
1. Press the Macro key programmed for the desired
series of commands for at least 2 seconds. The “Enter
User Code” prompt appears. The prompt remains
displayed for up to 10 seconds.
Enter your 4-digit user code.
The programmed macro sequence begins
automatically after the user code is entered.
8VLQJ'HYLFH&RPPDQGV
$ERXW'HYLFH&RPPDQGV
Your system may be set up so that it can control certain lights or other devices.
• Some devices may be automatically turned on or off by the system.
• You may be able to override automatically controlled devices using the
commands described below.
• Some devices can be manually turned on or off using the commands described
below.
• See your installer for a list of devices that may be set up for your system. A list
of these devices is provided at the back of this manual for you to fill out.
To Activate Devices:
+ [#] + [7] + 2-digit device number
(Security Code)
Alpha Display:
(-7%61)(
6)%(= 83 %61
Devices associated with that device number activate.
Fixed-Word Display: READY
To Deactivate Devices:
+ [#] + [8] + 2-digit device number
(Security Code)
Devices associated with that device number deactivate.
– 27 –
3DJLQJ)HDWXUH
$ERXW$XWRPDWLF3DJLQJ
Your system may be set up to automatically send alert messages to a pager as certain
conditions occur in your system.
• The following events can be programmed by your installer to be sent to the pagers:
arming and disarming†, alarms, and trouble conditions. († reports when
arming/disarming from a keypad using a security code; auto-arming/disarming,
arming with assigned button, and keyswitch arming do not send pager messages.)
• You can also program the system to send an automatic pager message to alert you
in the event that someone has not arrived home (disarmed the system) within a
defined period of time (see the Scheduling section for details on “latch key report”).
• Your installer programs the pager phone numbers and reporting events.
• The pager message consists of a 7-digit system status code that indicates the type of
condition that has occurred.
• An optional, predefined 16-digit character string can precede the 7-digit system
status code; these characters can consist of a PIN no., subscriber account no., or any
additional data that you may wish to have sent to the pager.
• The pager display format is as follows: 3-digit Event Code
Optional 16 digits
È
Æ AAAAAAAAAAAAAAAA – BBB – CCCC Å 1-digit partition + 3-digit User or Zone No.
A=
B=
Optional 16-digits for
Account numbers,
PIN numbers, or any
other data;
programmed by the
installer, if required.
A 3-digit code that
describes the event
that has occurred
in your system
(see for event
codes table below)
C=
A 1-digit partition number plus a 3-digit User or Zone
number, depending on the type of event that has
occurred, where:
• alarms and troubles display zone number
• arming/disarming (opens/closes) display user number
• single-digit user or zone numbers are preceded by a
zero.
The 3-digit Event Codes (BBB) that can be displayed are:
911 =
Alarms.
The 4-digit number
(CCCC) represents the
zone number that has
caused the alarm.
811 =
Troubles.
The 4-digit number
(CCCC) represents the
zone number that has
caused the trouble.
101 =
Open
(system disarmed).
The 4-digit number
(CCCC) represents the
user number that has
disarmed the system.
102 =
Close
(system armed).
The 4-digit number
(CCCC) represents the
user number that has
armed the system.
Examples of typical 7-digit pager displays follow.
– 28 –
Ex. 1.
³ = Alarm (911) on zone 4 (1004)
Ex. 2.
³ = Closing–system arming (102)– by user 5 (1005)
3DJLQJ)HDWXUH
0DQXDO3DJLQJ
Your system may be set up so you can manually send a message to a pager.
• Your installer programs the paging function key and the pager phone number.
• Pressing the paging keys sends the message
999–9999
to the pager.
• This message could mean “call home”, “call your office”, or any other prearranged
meaning.
• See the Paging chart at the back of this manual for details of the paging setup for
your system.
1. Hold pager key 2 seconds.
Alpha Display:
Press and hold the programmed Paging Key for at
least 2 seconds (wait for beep).
2. The recipient, on seeing the 999–9999 message, will
understand the prearranged meaning of this signal.
(-7%61)(
6)%(= 83 %61
Fixed-Word Display: READY
Pager Display
/DWFK.H\3DJLQJ
You can program a schedule that causes a pager report to be sent if the system is not
DISARMED by the scheduled time (see Scheduling section, event “03”). For example,
a working parent might want a message to be sent to a pager if their child did not
arrive home from school and disarm the system by a certain time.
If programmed, the message that is sent is:
7 7 7 –7777
.
– 29 –
6HFXULW\&RGHV$XWKRULW\/HYHOV
$ERXW6HFXULW\&RGHV
Your installer assigned a master code that is used to perform all system functions.
In addition, you can assign up to 15 different security codes for use by other users.
• Only the System Master can assign user codes to users.
• Users are identified by 2-digit user numbers (03-17 [users 01 and 02 are reserved]).
• In addition to a security code, each user is assigned various system attributes.
• User codes can be used interchangeably when performing system functions (a
system armed with one user's code can be disarmed by another user's code), with
the exception of the Guest code and Arm Only code described below.
• User code programming involves these steps:
1. Choose a user number and assign a 4-digit security code.
2. Assign an authority level to that user.
3. Assign other attributes as necessary (see attributes on the next page).
NOTE: The factory settings are designed to meet most normal user situations.
Therefore, the only step you usually need to do when adding users is assign a user
number and a security code.
$XWKRULW\/HYHO'HILQLWLRQV
Authority levels define the system functions a particular user can/cannot perform.
– 30 –
Level Title
Explanation
N/A
System Master
0
Standard User
1
Arm Only
Reserved for user 02; Can perform all system functions and assign
codes; can change its own code as described on the following page.
The default System Master code is 1234.
Can only perform security functions. Cannot perform other system
functions.
Can only arm the system. Cannot disarm or do other functions.
2
Guest
Can arm the system, but cannot disarm the system unless the
system was armed with this code. This code is typically assigned to
someone (e.g., babysitter or cleaner) who has a need to arm/disarm
the system only at certain times. The user of this code should not use
the “Quick Arming” feature.
3
Duress Code
Intended for use when you are forced to disarm or arm the system
under threat. When used, the system will act normally, but can
silently notify the Central Monitoring Station of your situation, if that
service has been provided.
6HFXULW\&RGHV$XWKRULW\/HYHOV&RQW
+RZWR$VVLJQ8VHU&RGHVDQG$WWULEXWHV
The following lists the various command strings for adding user codes and attributes.
Refer to the User Setup chart at the back of this manual for factory
assignments of user attributes and to keep a record of user programming.
System Master code + [8] + 02 + new Master code + new code again
Change System
Master Code
The System Master code can be changed only by using the current
System Master code or by the Installer using the Installer code
(Installer code + [8] + 02 + new System Master code)
Add User Code:
System Master code + [8] + user no. + new user’s code
User 01 = installer
User 03-16 = standard users
User 02 = master
(factory set master code is 1234)
The Keypad beeps once to confirm that new user was added.
Delete User Code:
System Master code + [8] + [user no.] + [#] [0]
The user code and all attributes programmed for this user number,
including any associated RF keys, are erased from the system.
Authority Level:
System Master code + [8] + [user no.] + [#] [1]+ auth. level
Authority Levels (see definitions on previous page):
0 = standard user
2 = guest
1 = arm only
3 = duress
Factory Assignments:
users 03-16 = 0
Access Group:
Factory Assignments: none
RF User Number:
Factory Assignments: none
System Master Code + [8] + [user no.] + [#] [2]+ group (1-8)
You can assign users to a group, then set an access schedule that
defines the times this group of users can operate the system. The
system ignores these users outside the scheduled times.
System Master Code + [8] + [user no.] + [#] [4]+ zone no.
Use this command to assign a wireless button device (keyfob) to this
user (keyfob must be enrolled in system first; see installer).
Zone number: enter the zone number assigned to a button on the
keyfob that will be used for arming/disarming by this user.
Pager On/Off:
System Master Code + [8] + [user no.] + [#] [5] + 0 or 1
Factory Assignments:
users 01-16 = 1 (on)
You can program a user so that a message is sent to a pager
whenever this code is used to arm or disarm the system.
Paging On/Off: 1 = allow paging; 0 = no paging for this user
– 31 –
6FKHGXOLQJ
$ERXW6FKHGXOLQJ
The system provides one end-user schedule (programmable by master/installer only),
which can control various types of events.
• Each schedule causes a defined event to start and stop (when appropriate) at a
specified time.
• Schedules can be set to automatically repeat at various intervals.
• Schedules can be set for random starting, if desired.
&UHDWLQJ6FKHGXOHV
+ [#] + [6] [4]
1.
(Master Code)
Alpha Displays:
(-7%61)(
6)%(= 83 %61
2. Enter “01” as the 2-digit schedule number.
Press [∗] to continue.
)28)6 7',)( 23
=59-8
3. Enter the desired 2-digit event number from the
)28)6 ):)28
following list.
00 = clear the scheduled event
01 = turn a programmed output on or off
(see Using Device Commands section for a list of output device numbers used
in your system)
02 = set a user access schedule for one or more users
(see Security Codes section for an explanation of access groups)
03 = send a “latch-key” report to a pager if the system is not disarmed by a specified
time; message sent is “777-7777.”
04 = automatically arm the system in STAY mode at a specified time
05 = automatically arm the system in AWAY mode at a specified time
06 = automatically disarm the system at a specified time
07 = Display the word “REMINDER” at a specified time
(if selected, the keypad will beep every 30 seconds beginning when the word
“REMINDER” is scheduled to display. To stop the beeps and cancel the display
once it starts, simply press any key.
Press [∗] to continue.
4. For event number “01,” enter the output number
associated with this schedule.
Otherwise, this prompt is skipped.
Press [∗] to continue to the “Start” prompt below.
– 32 –
():-') 291&)6
<<
6FKHGXOLQJFRQWLQXHG
5. For event number “02,” enter the access group
number. Otherwise, this prompt is skipped.
Press [∗] to continue to the “Start” prompt below.
7. Enter the event’s start time and days of week.
Hour = 00-12; minute = 00-59
AM = 0; PM = 1
Days = Position the cursor under the desired days
using the [∗] key to move forward, then press “1” to
select the day.
Press [∗] to continue.
8. If applicable, enter the event’s stop time and days of
week (applies only to event numbers 01, 02, and 03).
Refer to step 7 for available entries.
Press [∗] to continue.
9. Enter the desired repeat option.
0 = no repeat
1 = repeat schedule weekly
2 = repeat schedule biweekly (every other week)
3 = repeat schedule every third week
4 = repeat schedule every fourth week
e.g., To make a schedule that happens everyday you
would select all days with a repeat count of 1. To
make a schedule that runs for one week then stops,
select everyday with a repeat count of 0.
10. For event number 01 (output on/off), select the
desired randomize option. 0 = no; 1 = yes
If selected, the schedule times will vary within 60
minutes of the “hour” time. For example, if a
schedule is set to start at 6:15pm, it will do so the
first time 6:15pm arrives, but on subsequent days it
will start anytime between 6:00 and 6:59 p.m.
Press [∗] to return to first prompt, then enter 00 to
quit.
+6394 291&)6
<
78%68
718;8*7
,,11%1
7834
718;8*7
,,11%1
6)4)%8 348-32
<
6%2(31->)
=23 ==)7
<
– 33 –
(YHQW/RJJLQJ3URFHGXUHV
$ERXW(YHQW/RJJLQJ
The system records various events in a history log, which can be viewed by the master
user using an Alpha Display keypad.
• The Event Log holds up to 32 events.
• Events are displayed in chronological order, from most recent to oldest.
• When the log is full, the oldest event is replaced by the logging of any new event.
9LHZLQJWKH(YHQW/RJ
+ [#] +
1.
6 + 0
(Master Code)
Alpha Displays:
(-7%61)(
6)%(= 83 %61
2. The system displays the most recent event as follows:
• event number
• type of event, identified by its corresponding code
(see your installer for the meaning of each code)
• zone or user number (depending on type of event)
• time and date of the event’s occurrence.
3. Pressing [∗] displays previous events (back in time).
Pressing [#] displays events forward in time.
4. Exit the event log by pressing any key other than [∗]
or [#].
– 34 –
) 9 4
%1 (YHQW/RJJLQJ3URFHGXUHVFRQWLQXHG
7DEOHRI(YHQW/RJ&RGHV
The following table lists the codes that may appear when viewing the Event Log.
If the event code is preceded by an “E” (as in the example display on the previous
page), it means that the event is new and ongoing; if preceded by an “R,” it means the
event has been restored.
Code
110
121
122
123
131
Definition
Fire Alarm
Duress
Alarm, 24-hour Silent
Alarm, 24-hour Audible
Alarm, Perimeter
132
Alarm, Interior
134
Alarm, Entry/Exit
135
143
145
146
150
Alarm, Day/Night
Alarm, Expansion Module
ECP Module cover tamper
Silent Burglary
Alarm, 24-Hour Auxiliary/Monitor
zone
Carbon Monoxide
AC Power
Low System Battery/Battery Test
Fail
System Reset (Log only)
Battery Test Failure
Bell/Siren Trouble
Trouble, Expansion Mod.
Supervision
Trouble, ECP Cover Tamper
RF Receiver Jam
Telco Line Fault
Long Range Radio Trouble
Fire Loop Trouble
Exit Error Alarm
Global Trouble, Trouble
Day/Night
162
301
302
305
309
321
333
341
344
351
353
373
374
380
Code
381
382
383
384
393
401
403
406
407
408
409
441
442
570
601
602
606
607
623
625
627
628
750 789
Definition
RF Supervision Trouble
Supervision Auxiliary Wire Zone
RF Sensor Tamper
RF Sensor Low-battery
Clean Me
Disarmed, Armed AWAY,
Armed STAY
Schedule Arm/Disarm AWAY
Cancel by User
Remote Arm/Disarm
(Downloading)
Quick Arm AWAY
Keyswitch Arm/Disarm AWAY
Disarmed/Armed
STAY/INSTANT,
Quick-Arm STAY/INSTANT
Keyswitch Arm/Disarm STAY
Bypass
Manually Triggered Dialer Test
Periodic Test
AAV to Follow
Walk Test Entered/Exited
Event Log 80% Full
Real-Time Clock was Changed
(log only)
Program Mode Entry (log only)
Program Mode Exit (log only)
Reserved for Configurable Zone
Type report codes (check with
central station when using these
codes)
– 35 –
7HVWLQJWKH6\VWHP7R%H&RQGXFWHG:HHNO\
$ERXW7HVWLQJWKH6\VWHP
Using Test mode allows each protection point to be checked for proper operation.
• The keypad sounds a single beep every 40 seconds as a reminder that the
system is in the Test mode.
• Alarm messages are not sent to your Central Station while Test mode is on.
1. Disarm the system and close all protected windows,
doors, etc. The READY indicator light should come
on if all zones are intact (i.e., all protected windows,
doors, etc. are closed.
+
2.
(Security Code)
5
Alpha Displays:
(-7%61)(
6)%(= 83 %61
then [0] (walk)
= (-%0
= ;%0/
TEST
The Dial test (option “1”) is intended for the installer
and should not be used unless directed to do so by
your Security System Representative.
3. Listen. The external sounder should sound for 1
second and then turn off. If the sounder does not
sound, CALL FOR SERVICE.
8)78 -2 463+6)77
4. Fault zones. Open each protected door and window in turn and listen for three
beeps from the keypad. Identification (zone number or zone description) of each
faulted protection point should appear on the display. The display clears when the
door or window is closed.
5. Walk in front of any interior motion detectors (if used) and listen for three beeps.
The identification of the detector should appear on the display when it is activated.
The display clears when no motion is detected.
Note that if wireless motion detectors are used, there is a 3-minute delay between
activations. This is to conserve battery life.
6. Test all smoke detectors, following the manufacturer's instructions. The
identification of each detector should appear on the display when each is activated.
If a problem is experienced with any protection point (no confirming sounds, no
display), call for service immediately.
When all protection points have been checked and are intact (closed), there should
be no zone identification numbers displayed on the keypad.
+ [1]
7. Exit test mode:
(Security Code)
If the test mode is inadvertently left active, it automatically turns off after 4 hours.
During the final five minutes, the keypad will emit a double beep every 30 seconds.
– 36 –
7URXEOH&RQGLWLRQV
"Check" and
"Battery" Displays
The word CHECK on the keypad's display, accompanied by a
"beeping" at the keypad, indicates a trouble condition in the system.
To silence the beeping for these conditions, press any key.
1. A display of "CHECK" and one or more zone numbers
indicates that a problem exists with the displayed zone(s) and
requires your attention. Determine if the zone(s) displayed are
intact and make them so if they are not. If the problem has been
corrected, the display can be cleared if you enter the OFF
sequence (security code plus OFF key) twice. If the display
persists, CALL FOR SERVICE.
Note: A display of CHECK 70 on Alpha Display keypads
indicates that the wiring connection to the external sounder is
at fault (opened or shorted), and you should CALL FOR
SERVICE. See “BELL FAILURE” on next page. A display of
CHECK 90 indicates that RF interference may be impeding the
operation of wireless sensors* in the system. See “Rcvr Jam”
on next page.
* Not all systems
use wireless
sensors.
2. If there are wireless sensors* in your system, the CHECK
condition may also be caused by some change in the
environment that prevents the wireless receiver from receiving
messages from a particular sensor. CALL FOR SERVICE if this
occurs.
IF YOU CANNOT CORRECT A "CHECK" DISPLAY,
CALL FOR SERVICE.
TYPICAL "CHECK" DISPLAYS
06
AC
',)'/ CHECK
&)(6331 ;-2(3;
FIXED-WORD DISPLAY KEYPAD
ALPHA DISPLAY KEYPAD
– 37 –
7URXEOH&RQGLWLRQV&RQWLQXHG
Words or letters in parentheses ( ) are those that are
displayed on Alpha Display keypads.
Other Trouble
Displays
COMM. FAILURE
(or FC)
Indicates that a failure has occurred in
the telephone communication portion of
your system.
CALL FOR SERVICE.
SYSTEM LO BAT
(or BAT with no
zone No.)
Indicates that a low system battery
condition exists. Display is
accompanied by "beeping"* at the
keypad. If this condition persists for
more than one day (with AC present),
CALL FOR SERVICE.
LO BAT
+ zone descriptor
(or BAT with
zone No.)
Indicates that there is a low battery
condition in the wireless transmitter**
number displayed (00 is RF keypad).
Accompanied by a single "beep"* (about
once every 40 seconds) at the keypad.
Either replace the battery yourself, or
CALL FOR SERVICE. If the battery is
not replaced within 30 days, a CHECK
display may occur.
Rcvr Jam
(or CHECK 90)
Wireless part of the system is experiencing
RF interference which may impede
reception from wireless sensors.**
ALARM 1xx
FAULT 1xx
CHECK 1xx
(or 91)
Indicates a communication problem
between the control and a connected
device (e.g., RF receiver, zone expander)
where the “xx” indicates the device
address. CALL FOR SERVICE.
MODEM COMM
(or CC)
Indicates that the control is on-line with
the Central Monitoring Station's remote
computer.
The control will not operate while on-line.
Wait a few minutes — the display should
disappear.
BELL FAILURE
(or CHECK 70)
Indicates that the wiring connection to
the external sounder is at fault (open or
shorted). Accompanied by “beeping” at
the keypad. CALL FOR SERVICE.
* Any “beeping” that
accompanies a trouble
display can be stopped
by depressing any key
on the keypad or by
entering an OFF
sequence (code + OFF)
** Not all systems use
wireless sensors.
– 38 –
7URXEOH&RQGLWLRQV&RQWLQXHG
Other Trouble
Displays
(Continued)
AC LOSS
(or NO AC)
The system is operating on battery power
only due to an AC power failure.
If only some lights are out on the premises,
check circuit breakers and fuses and
reset or replace as necessary.
If AC power cannot be restored and a
“low system battery” message appears
(see previous page), CALL FOR
SERVICE.
Busy-Standby
(or dI)
If this message remains displayed for more
than 1 minute, system is disabled. CALL
FOR SERVICE.
OPEN CIRCUIT
(or OC)
The keypad is not receiving signals from
the control. CALL FOR SERVICE.
Long Rng Trbl
(or bF)
If part of your system, back-up Long
Range Radio communication has failed.
CALL FOR SERVICE.
TELCO FAULT
(or CHECK 94)
The telephone line has a problem.
CALL FOR SERVICE.
Total Power Failure If there is no keypad display at all, and the READY indicator
is not lit, operating power (from AC and back-up battery) for the
system has stopped and the system is inoperative. CALL FOR
SERVICE.
In The Event Of Telephone Operational Problems
In the event of telephone operational problems, disconnect the control from the phone line by
removing the plug from the phone wall jack. We recommend that your installer demonstrate this
disconnection on installation of the system. Do not attempt to disconnect the phone connection
inside the control. Doing so will result in the loss of your phone lines. If the regular phones work
correctly after the control has been disconnected from the phone wall jack, the control has a
problem and you should immediately call for service. If upon disconnection of the control, there is
still a problem on the phone line, notify the Telephone Company that they have a problem and
request prompt phone repair service. The user may not under any circumstances attempt any
service or repairs to the security system. Repairs must be made only by authorized service (see
the LIMITED WARRANTY statement for information on how to obtain service).
– 39 –
0DLQWDLQLQJ<RXU6\VWHP
Taking Care of
Your System
The components of your security system are designed to be as
maintenance-free as possible. However, to make sure that your system
is in reliable working condition, do the following:
1. Test your system weekly.
2. Test your system after any alarm occurs.
Silencing Low
Battery Warning
Tones at the
Keypad
You can silence the keypad’s warning tones by pressing the OFF key,
but the keypad's low battery message display will remain on as a
reminder that you have a low battery condition in one or more of your
wireless sensors. When you replace the weak battery with a fresh one,
the sensor sends a "good battery" signal to the control as soon as the
sensor is activated (opening/closing of door, window, etc.), causing the
low battery display to turn off. If the sensor is not activated, the display
will automatically clear within approximately 1 hour.
Replacing
Batteries in
Wireless Sensors
Each wireless sensor in your system has a 9-volt or 3-volt battery. The
system detects a low battery in wireless sensors, including smoke
detectors, the personal emergency transmitter, and the portable
wireless keypad and displays a low battery message*. (A low battery in
a portable wireless keypad is detected as soon as one of its keys is
pressed, and displayed as 00.). Battery-operated smoke detectors with
a low battery also emit a single "chirp" sound approximately once
every 20–30 seconds.
Alkaline batteries provide a minimum of 1 year of operation, and in
most units and applications, provide 2–4 years of service. 3-volt lithium
batteries provide up to 4 or more years of operation. Actual battery life
will depend on the environment in which the sensor is used, the
number of signals that the transmitter in the sensor has had to send,
and the specific type of sensor. Factors such as humidity, high or low
temperatures or large swings in temperature, may all lead to the
reduction of actual battery life in an installation.
Wireless sensors
may not have
been used in your
security system
IMPORTANT:
Use only batteries
recommended by
your installer as
replacement.
* The low battery message comes on as a warning that battery replacement
in indicated sensor(s) is due within 30 days. In the meantime, a sensor
causing a low battery indication is still fully operational.
Routine Care • Treat the components of your security system as you would any other
electrical equipment. Do not slam sensor-protected doors or windows.
• Keep dust from accumulating on the keypad and all protective
sensors, particularly on motion sensors and smoke detectors.
• The keypad and sensors should be cleaned carefully with a dry soft
cloth. Do not spray water or any other fluid on the units.
– 40 –
)LUH$ODUP6\VWHP,I,QVWDOOHG
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS
General
Your fire alarm system (if installed) is on 24 hours a day, for
continuous protection. In the event of an emergency, the strategically
located smoke and heat detectors will sound their alarms and
automatically send signals to your system, triggering a loud,
interrupted pulsed sound* from the Keypad(s) and any external
sounders. A FIRE message will appear at your Keypad and remain on
until you silence the alarm (see below for silencing fire alarms).
* Temporal pulse sounding is produced for Fire alarms, as follows:
3 pulses–pause–3 pulses–pause–3 pulses–pause. . . , repeated.
TYPICAL FIRE EMERGENCY DISPLAYS
*-6) 1%78)6
&)(6331
ALPHA DISPLAY KEYPAD
Silencing
Fire Alarms and
Clearing Memory
of Alarm
1.
AC
ALARM
FIRE
FIXED-WORD KEYPAD
You can silence the alarm at any time by pressing the OFF key (the
security code is not needed to silence fire alarms). To clear the
display, enter your code and press the OFF key again (to clear
Memory of Alarm).
2. If the Keypad's FIRE display does not clear after the second OFF
sequence, smoke detectors may still be responding to smoke or heat
producing objects in their vicinity. Investigate, and should this be
the case, eliminate the source of heat or smoke.
3. If this does not remedy the problem, there may still be smoke in the
detector. Clear it by fanning the detector for about 30 seconds.
When the problem has been corrected, clear the display by
entering your code and pressing the OFF key.
Smoke Detector Depending on the type of smoke detectors in your system, it may be
Reset necessary to "reset" the smoke detectors after a fire alarm has been
turned off. Check with your installer. This "reset" is accomplished at a
keypad, as follows:
Enter User Code*, then press the [1] key (* except “arm only” user).
– 41 –
)LUH$ODUP6\VWHP&RQWLQXHG
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS
Manually 1. Should you become aware of a fire emergency before your smoke or
heat detectors sense the problem, go to your nearest keypad and
Initiating
manually initiate an alarm by pressing the panic key assigned for
a Fire Alarm
FIRE emergency for 2 seconds. If a key pair has been assigned for
fire, press both keys at the same time. See the Using the Panic Keys
section below for further details.
2. Evacuate all occupants from the premises.
3. If flames and/or smoke are present, leave the premises and notify
your local Fire Department immediately.
4.
Using the Panic
Key(s) Assigned
for FIRE
Emergency
If no flames or smoke are apparent, investigate the cause of the
alarm. The zone number(s) of the zone(s) in an alarm condition will
be displayed at the keypad.
A key or key pair may have been assigned for manually initiating a
FIRE alarm. See the Panic Keys section for key assignments.
For convenience, indicate the key or key pair assigned for fire below.
In divi dua l Ke ys
A
B
C
Press the individual key assigned for fire for 2
seconds.
OR
Key Pai rs
1
∗
3
OFF
READY
STAY
and
∗
READY
and
#
and
#
Press the key pair assigned
for fire at the same time.
DISPLAYS FOLLOWING MANUAL INITIATION OF A FIRE ALARM
*-6) ALARM
FIRE
ALPHA DISPLAY KEYPAD
– 42 –
FIXED-WORD KEYPAD
AC
)LUH$ODUP6\VWHP&RQWLQXHG
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS
1DWLRQDO)LUH3URWHFWLRQ$VVRFLDWLRQ
5HFRPPHQGDWLRQVRQ6PRNH'HWHFWRUV
With regard to the number and placement of smoke/heat detectors, we
subscribe to the recommendations contained in the National Fire Protection
Association's National Fire Alarm Code (NFPA 72) noted below.
Early warning fire detection is best achieved by the installation of fire
detection equipment in all rooms and areas of the household as follows: A
smoke detector installed outside of each separate sleeping area, in the
immediate vicinity of the bedrooms and on each additional story of the
family living unit, including basements and excluding crawl spaces and
unfinished attics.
In addition, the NFPA recommends that you install heat or smoke detectors
in the living room, dining room, bedroom(s), kitchen, hallway(s), attic,
furnace room, utility and storage rooms, basements and attached garages.
✪
KITCHEN
▲
DINING
✪
✪
BEDROOM BEDROOM
✪
TV ROOM
■
▲
KITCHEN
✪
DINING
LIVING ROOM
■
✪
✪
LIVING ROOM
BEDROOM
■
✪
✪
BDRM
BDRM
✪
BEDROOM
✪
▲
■ Smoke Detectors for Minimum Protection
✪ Smoke Detectors for Additional Protection
▲ Heat-Activated Detectors
■
BEDROOM
■
✪
BEDROOM
■
TO
BR
✪
BEDROOM
▲
▲
KTCHN
LVNG RM
■
.
CLOSED
DOOR
GARAGE
BASEMENT
– 43 –
)LUH$ODUP6\VWHP&RQWLQXHG
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS
(PHUJHQF\(YDFXDWLRQ
PORCH
OM
ET
RO
OS
D
L
E
C
B
M
OM
OO
TH
RO
D
DR
BA
E
BE
B
2ND FLOOR
EN
CH
KIT
BACK DOOR
M
OO
DR
E
B
M
OO
TH
DR
BA
E
B
1ST FLOOR
•
•
BACK
•
FRONT
– 44 –
Establish and regularly practice a plan of escape in the
event of fire. The following steps are recommended by
the National Fire Protection Association:
1. Position your detector or your interior and/or
exterior sounders so that they can be heard by all
occupants.
2. Determine two means of escape from each room.
One path of escape should lead to the door that
permits normal exit from the building. The other
may be a window, should your path be impassable.
Station an escape ladder at such windows if there
is a long drop to the ground.
3. Sketch a floor plan of the building. Show windows,
doors, stairs and rooftops that can be used to
escape. Indicate escape routes for each room. Keep
these routes free from obstruction and post copies
of the escape routes in every room.
4. Assure that all bedroom doors are shut while you
are asleep. This will prevent deadly smoke from
entering while you escape.
5. Try the door. If the door is hot, check your
alternate escape route. If the door is cool, open it
cautiously. Be prepared to slam the door if smoke
or heat rushes in.
6. When smoke is present, crawl on the ground. Do
not walk upright, since smoke rises and may
overcome you. Clearer air is near the floor.
7. Escape quickly; don't panic.
8. Establish a common meeting place outdoors, away
from your house, where everyone can meet and
then take steps to contact the authorities and
account for those missing. Choose someone to
assure that nobody returns to the house — many
die going back
4XLFN*XLGHWR%DVLF6\VWHP)XQFWLRQV
FUNCTION
PROCEDURE
COMMENTS
Check Zones
Press READY key.
View faulted zones when system not
ready.
Arm System
Enter code. Press arming key desired:
(AWAY, STAY, NIGHT-STAY,
MAXIMUM, INSTANT)
Arms system in mode selected.
Quick Arm
(if programmed)
Press #. Press arming key desired:
(AWAY, STAY, MAXIMUM, INSTANT)
Arms system in mode selected, quickly
and without use of a code.
Bypass Zone(s)
Enter code. Press BYPASS key.
Enter zone number(s) to be bypassed
(use 2-digit entries).
Bypassed zones are unprotected and
will not cause an alarm if violated.
Quick Bypass
(if programmed)
Enter code. Press BYPASS key + [#].
Bypasses all faulted zones
automatically.
Enter code. Press OFF key.
Also disarms system. Memory of alarm
remains until cleared.
Press OFF key.
Press any key.
Memory of Alarm remains until cleared.
Determine cause.
Disarm System
Enter code. Press OFF key.
Also silences sounders. Memory of
alarm remains until cleared.
Clear Alarm
Memory
After disarming, enter code again.
Press OFF key again.
Keypad beeps rapidly on entry if alarm
has occurred while absent. Alarm
display will remain upon disarming
until cleared.
Duress (if active
and connected to
Central Station)
Arm or disarm "normally", but
use your 4-digit Duress code to do so.
Performs desired action and sends
silent alarm to Central Station.
Panic Alarms
(as programmed)
Press key [A], [B], or [C] for at least 2
seconds or press and hold designated key
pairs: [1]+[∗], or [∗] + [#], or [3] + [#].
See the Panic Keys section for
emergency functions programmed for
your system. Note: Keys “A”, “B”, and
“C” may have been programmed for
other functions.
Chime Mode
To turn ON or OFF: Enter code. Press
CHIME key.
The keypad will sound if doors or
windows are violated while system is
disarmed and chime mode is ON.
Test Mode
To turn ON: Enter code. Press TEST key. Tests alarm sounder and allows sensors
To turn OFF: Enter code. Press OFF key. to be tested.
Phone Access
if applicable
Consult Phone Access User's Guide that
accompanies the Phone Module.
Silence Sounders
Burglary:
Fire:
"Check":
Permits system access remotely, via
Touch-tone phone.
– 45 –
6XPPDU\RI$XGLEOH9LVXDO1RWLILFDWLRQV
)L[HG:RUG'LVSOD\.H\SDGV SOUND
CAUSE
DISPLAY
LOUD,
INTERRUPTED*
FIRE ALARM
FIRE is displayed; zone number of zone in
alarm is displayed. If a fire alarm is manually
activated, zone number 95 will be displayed.
LOUD,
CONTINUOUS*
Keypad & Ext.
BURGLARY/AUDIBLE
EMERGENCY ALARM
ALARM is displayed. Zone number of zone in
alarm is also displayed.
ONE SHORT BEEP
(not repeated)
Keypad only
a. SYSTEM DISARM
b. SYSTEM ARMING ATTEMPT
WITH AN OPEN ZONE.
a. READY indicator light comes on.
b. Number of the open protection zone displayed.
c. BYPASS VERIFY
c. Zone numbers of the bypassed protection
zones are displayed (one beep is heard for
each zone displayed). Subsequently, BYPASS
is displayed.
ONE SHORT BEEP
(once every 40 secs)
Keypad only
a. SYSTEM IS IN TEST MODE
b. LOW BATTERY AT A
TRANSMITTER
c. SYSTEM WILL AUTOARM
WITHIN 10 MINUTES
a. Opened zone numbers will appear.
b. BAT displayed with zone number of
transmitter.
c. No special display.
TWO SHORT BEEPS
Keypad only
ARM AWAY or MAXIMUM
AWAY is displayed. Red ARMED indicator is lit.
THREE SHORT
BEEPS
Keypad only
a. ARM STAY, NIGHT-STAY, OR
INSTANT
a. STAY or INSTANT is displayed. Red
ARMED indicator is lit.
b. ZONE OPENED WITH
SYSTEM IN CHIME MODE.
b. CHIME displayed; zone number of open
protection zone will be displayed if the [✱]
key is pressed.
Keypad & Ext.
RAPID BEEPING
Keypad only
a. TROUBLE
b. MEMORY OF ALARM
a. CHECK displayed. Zone number of troubled
protection zone is displayed.
b. FIRE or ALARM is displayed; zone number
of zone in alarm is displayed
c. BAT displayed with no zone ID number.
c. SYSTEM LOW BATTERY
d. EXT. SOUNDER WIRING FAIL d. CHECK 70 is displayed.
SLOW BEEPING
Keypad only
a. EXIT DELAY WARNING
a. AWAY is displayed.
b. ENTRY DELAY WARNING
b. Exceeding the entry delay time without
disarming causes alarm.
* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.
– 46 –
6XPPDU\RI$XGLEOH9LVXDO1RWLILFDWLRQV
$OSKD'LVSOD\.H\SDGV
SOUND
LOUD,
INTERRUPTED*
Keypad & Ext.
CAUSE
DISPLAY
FIRE ALARM.
FIRE is displayed; descriptor of zone in alarm is
displayed. If a fire alarm is manually activated, zone
number 95 will be displayed.
LOUD,
CONTINUOUS*
Keypad & Ext.
BURGLARY/AUDIBLE
EMERGENCY ALARM.
ALARM is displayed. If programmed, descriptor of
zone in alarm is also displayed
ONE SHORT BEEP
(not repeated)
Keypad only
a. SYSTEM DISARM.
a. DISARMED/READY TO ARM is displayed.
b. SYSTEM ARMING ATTEMPT
WITH AN OPEN ZONE.
b. Number and descriptor of open protection zone is
displayed.
c. BYPASS VERIFY.
c. Numbers and descriptors of the bypassed zones
are displayed (One beep is heard for each
zone displayed). Subsequently, the following is
displayed: DISARMED BYPASS /Ready to Arm.
a. SYSTEM IS IN TEST MODE.
b, LOW BATTERY AT A
TRANSMITTER.
c. SYSTEM WILL AUTOARM
WITHIN 10 MINUTES
a. Opened Zone identifications will appear.
b. LO BAT displayed with description of transmitter.
ONE SHORT BEEP
(once every 40 secs)
Keypad only
c. No special display.
TWO SHORT BEEPS
Keypad only
ARM AWAY or MAXIMUM.
ARMED AWAY or MAXIMUM displayed. Red
ARMED indicator lit.
THREE SHORT
BEEPS
Keypad only
a. ARM STAY, NIGHT-STAY,
OR INSTANT.
a. ARMED STAY or ARMED INSTANT displayed.
Red ARMED indicator lit.
RAPID BEEPING
Keypad only
b. ZONE OPENED WHILE
SYSTEM IS DISARMED.
a. TROUBLE.
b. MEMORY OF ALARM.
b. CHIME displayed, descriptor of open protection
zone will be displayed if the [✱] key is pressed.
a. CHECK displayed. Descriptor of troubled
protection zone is displayed.
b. FIRE or ALARM is displayed; descriptor of zone
in alarm is displayed.
c. SYSTEM LO BAT displayed.
c. SYSTEM LOW BATTERY.
d. EXT. SOUNDER WIRE FAIL. d. BELL FAILURE is displayed.
SLOW BEEPING
Keypad only
a. EXIT DELAY WARNING
(if programmed).
a. ARMED AWAY OR MAXIMUM is displayed
along with You May Exit Now.
b. ENTRY DELAY WARNING.
b. DISARM SYSTEM OR ALARM WILL OCCUR
is displayed. Exceeding the delay time without
disarming causes an alarm.
* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.
– 47 –
5HJXODWRU\6WDWHPHQWVDQG:DUQLQJV
NOTE: This is a “Grade A” Residential System
RADIO FREQUENCY EMISSIONS
Federal Communications Commission (FCC) Part 15
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
TELEPHONE/MODEM INTERFACE
FCC Part 68
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration
number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested.
This equipment uses the following USOC jack: RJ31X
This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This
equipment is hearing-aid compatible.
Industry Canada
NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications
network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications
company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with
the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user
to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together, This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or
electrician, as appropriate.
Ringer Equivalence Number Notice:
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed
to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Industrie Canada
AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de
protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences
techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de
télécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il
est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.
Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de
télécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par
l’utilisateur ou à cause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques
et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions
rurales.
Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des
installations électriques, ou à un électricien, selon le cas.
AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui
peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à
la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
– 48 –
&KDUWVRI<RXU6\VWHP·V)HDWXUHV
SERVICING INFORMATION
Your local authorized service representative is the person best qualified to service your
alarm system. Arranging some kind of regular service program with him is advisable.
Your local service representative is:
Name:
Address:
Phone:
General Features
Features
Exit Delay
Entry Delay 1
Entry Delay 2
Night-Stay Zones
Quick Arm
Quick Bypass
Automatic Paging
Keyswitch Arming
(circle type of LED lighting)
Comments
Zones:
yes
yes
yes
Arm AWAY:
Arm STAY:
no
no
no
steady
steady
A
D
users:
flash
flash
Function Keys
Function Keys
B
C
Comments
• Single-Button Arming
• Step Arming
• Paging (see Paging chart)
• Time/Date Display
• Macro Key
• Emergency Key††: Personal
• Emergency Key††: Silent Alarm
• Emergency Key††: Audible Alarm
• Emergency Key††: Fire
• Device Activation
†† Emergency Keys:
Device:
A = [1] / [∗]
B = [∗] / [#]
C = [3] / [#]
– 49 –
&KDUWVRI<RXU6\VWHP·V)HDWXUHV
User Setup
The following chart will help keep track of system users. To program a user attribute:
Enter system master code + [8] + user no. + “#” command listed in column heading…
User
Name
User
No.
Security
Code
Auth.
Level
Access
Group
RF Zone
Number
Pager
on/off
enter new code
[#] [1] + level
[#] [2] + group
[#] [4] + zone no.
[#] [5] + 0/1
01
installer
02
system master
03
04
05
06
07
08
09
10
11
12
13
14
15
16
Authority Levels: 0 = standard user
1 = arm only
2 = guest
3 = duress
installer
master
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
Paging:
0 = no paging
1 = allow paging
Paging Setup
Pager Phone Number\
Prefix Characters
Automatically Reports Upon…
open/close alarm/trouble
zone list
Sched. Func. Key
Pager
Schedules: master code + [#] + [6] [4].
No.
Event
Device No.
(see list below)
for “01” events:
Group No.
for “02” events:
(see device list below) enter 1-8
Start
Time/ Day
Stop
Time/ Day
Repeat
Random
(0-4)
(yes/no)
01
Events:
00 = clear event
03 = latch key report
06 = auto disarm
01 = device on/off
04 = forced STAY arm
07 = display “reminder”
02 = user access
05 = forced AWAY arm
Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week
List of Output Devices
Device
01
02
03
04
– 50 –
Description
Schedule No.
Function Key
²1RWHV²
– 51 –
²1RWHV²
– 52 –
OWNER’S INSURANCE PREMIUM CREDIT REQUEST
This form should be completed and forwarded to your homeowner’s insurance carrier for possible
premium credit.
A. GENERAL INFORMATION:
Insured’s Name and Address:
Insurance Company:
Policy No.:
FA130CP
Type of Alarm:
Other ______________________________
Burglary
Fire
Installed by:
Both
Serviced by:
Name
Name
Address
Address
B. NOTIFIES (Insert B = Burglary, F = Fire)
Local Sounding Device
Police Dept.
Central Station
Fire Dept.
Name:
Address:
Phone:
C. POWERED BY: A.C. With Rechargeable Power Supply
D. TESTING:
Quarterly
Monthly
Weekly
Other
continued on other side
– 53 –
OWNER’S INSURANCE PREMIUM CREDIT REQUEST
(cont.)
E. SMOKE DETECTOR LOCATIONS
Furnace Room
Kitchen
Bedrooms
Attic
Basement
Living Room
Dining Room
Hall
Basement Door
Rear Door
All Exterior Doors
All windows
Interior locations
F. BURGLARY DETECTING DEVICE LOCATIONS:
Front Door
st
1 Floor Windows
All Accessible Openings, Including Skylights, Air Conditioners and Vents
G. ADDITIONAL PERTINENT INFORMATION:
Signature:
– 54 –
Date:
/,0,7$7,2162)7+,66<67(0
WARNING!
THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other
emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a
variety of reasons. For example:
• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm
sensor or disconnect an alarm warning device.
• Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work
without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are
not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason,
however briefly.
• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even
if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into
the path.
• A user may not be able to reach a panic or emergency button quickly enough.
• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not
activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published
by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this
System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke
detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or
roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or
building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors
have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not
always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping
gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.
Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as
anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.
• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their
installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple
beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot
detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or
windows.
Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the
optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however,
as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection
performance can decrease.
• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on
the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the
bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may
not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing
traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.
• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of
service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.
• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond
appropriately.
• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed
to last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.
This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for
insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and
continue to insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved
ones to learn about these developments.
– 55 –
21( <($5 /,0,7(' :$55$17<
+RQH\ZHOO ,QWHUQDWLRQDO ,QF DFWLQJ WKURXJK LWV )LUVW $OHUW 3URIHVVLRQDO EXVLQHVV 6HOOHU (LOHHQ :D\
6\RVVHW 1HZ <RUN ZDUUDQWV LWV First Alert Professional VHFXULW\ HTXLSPHQW WKH SURGXFW WR EH IUHH
IURP GHIHFWV LQ PDWHULDOV DQG ZRUNPDQVKLS IRU RQH \HDU IURP GDWH RI RULJLQDO SXUFKDVH XQGHU QRUPDO XVH DQG
VHUYLFH 6HOOHU
V REOLJDWLRQ LV OLPLWHG WR UHSDLULQJ RU UHSODFLQJ DW LWV RSWLRQ IUHH RI FKDUJH IRU SDUWV ODERU RU
WUDQVSRUWDWLRQ DQ\ SURGXFW SURYHQ WR EH GHIHFWLYH LQ PDWHULDOV RU ZRUNPDQVKLS XQGHU QRUPDO XVH DQG VHUYLFH
6HOOHU VKDOO KDYH QR REOLJDWLRQ XQGHU WKLV ZDUUDQW\ RU RWKHUZLVH LI WKH SURGXFW LV DOWHUHG RU LPSURSHUO\
UHSDLUHG RU VHUYLFHG E\ DQ\RQH RWKHU WKDQ WKH 6HOOHU ,Q FDVH RI GHIHFW FRQWDFW WKH VHFXULW\ SURIHVVLRQDO ZKR
LQVWDOOHG DQG PDLQWDLQV \RXU VHFXULW\ HTXLSPHQW RU WKH 6HOOHU IRU SURGXFW UHSDLU
7KLV RQH \HDU /LPLWHG :DUUDQW\ LV LQ OLHX RI DOO RWKHU H[SUHVV ZDUUDQWLHV REOLJDWLRQV RU OLDELOLWLHV 7+(5(
$5( 12 (;35(66 :$55$17,(6 :+,&+ (;7(1' %(<21' 7+( )$&( +(5(2) $1< ,03/,('
:$55$17,(6 2%/,*$7,216 25 /,$%,/,7,(6 0$'( %< 6(//(5 ,1 &211(&7,21 :,7+ 7+,6
352'8&7 ,1&/8',1* $1< ,03/,(' :$55$17< 2) 0(5&+$17$%,/,7< 25 ),71(66 )25
$ 3$57,&8/$5 385326( 25 27+(5:,6( $5( /,0,7(' ,1 '85$7,21 72 $ 3(5,2' 2) 21(
<($5 )520 7+( '$7( 2) 25,*,1$/ 385&+$6( $1< $&7,21 )25 %5($&+ 2) $1<
:$55$17< ,1&/8',1* %87 127 /,0,7(' 72 $1< ,03/,(' :$55$17< 2)
0(5&+$17$%,/,7< 0867 %( %528*+7 :,7+,1 0217+6 )520 '$7( 2) 25,*,1$/
385&+$6( ,1 12 &$6( 6+$// 6(//(5 %( /,$%/( 72 $1<21( )25 $1< &216(48(17,$/
25 ,1&,'(17$/ '$0$*(6 )25 %5($&+ 2) 7+,6 25 $1< 27+(5 :$55$17< (;35(66 25
,03/,(' 25 8321 $1< 27+(5 %$6,6 2) /,$%,/,7< :+$762(9(5 (9(1 ,) 7+( /266 25
'$0$*( ,6 &$86(' %< 7+( 6(//(5
6 2:1 1(*/,*(1&( 25 )$8/7 6RPH VWDWHV GR QRW DOORZ
OLPLWDWLRQ RQ KRZ ORQJ DQ LPSOLHG ZDUUDQW\ ODVWV RU WKH H[FOXVLRQ RU OLPLWDWLRQ RI LQFLGHQWDO RU FRQVHTXHQWLDO
GDPDJHV VR WKH DERYH OLPLWDWLRQ RU H[FOXVLRQ PD\ QRW DSSO\ WR \RX
6HOOHU GRHV QRW UHSUHVHQW WKDW WKH SURGXFW PD\ QRW EH FRPSURPLVHG RU FLUFXPYHQWHG WKDW WKH SURGXFW ZLOO
SUHYHQW DQ\ SHUVRQDO LQMXU\ RU SURSHUW\ ORVV E\ EXUJODU\ UREEHU\ ILUH RU RWKHUZLVH RU WKDW WKH SURGXFW ZLOO LQ
DOO FDVHV SURYLGH DGHTXDWH ZDUQLQJ RU SURWHFWLRQ %X\HU XQGHUVWDQGV WKDW D SURSHUO\ LQVWDOOHG DQG PDLQWDLQHG
DODUP PD\ RQO\ UHGXFH WKH ULVN RI D EXUJODU\ UREEHU\ ILUH RU RWKHU HYHQWV RFFXUULQJ ZLWKRXW SURYLGLQJ DQ
DODUP EXW LW LV QRW LQVXUDQFH RU D JXDUDQWHH WKDW VXFK ZLOO QRW RFFXU RU WKDW WKHUH ZLOO EH QR SHUVRQDO LQMXU\ RU
SURSHUW\ ORVV DV D UHVXOW &216(48(17/< 6(//(5 6+$// +$9( 12 /,$%,/,7< )25 $1<
3(5621$/ ,1-85< 3523(57< '$0$*( 25 27+(5 /266 %$6(' 21 $ &/$,0 7+( 352'8&7
)$,/(' 72 *,9( :$51,1* +2:(9(5 ,) 6(//(5 ,6 +(/' /,$%/( :+(7+(5 ',5(&7/< 25
,1',5(&7/< )25 $1< /266 25 '$0$*( $5,6,1* 81'(5 7+,6 /,0,7(' :$55$17< 25
27+(5:,6( 5(*$5'/(66 2) &$86( 25 25,*,1 6(//(5
6 0$;,080 /,$%,/,7< 6+$//
127 ,1 $1< &$6( (;&((' 7+( 385&+$6( 35,&( 2) 7+( 352'8&7 :+,&+ 6+$// %( 7+(
&203/(7( $1' (;&/86,9( 5(0('< $*$,167 6(//(5 7KLV ZDUUDQW\ JLYHV \RX VSHFLILF OHJDO
ULJKWV DQG \RX PD\ DOVR KDYH RWKHU ULJKWV ZKLFK YDU\ IURP VWDWH WR VWDWH 1R LQFUHDVH RU DOWHUDWLRQ ZULWWHQ RU
YHUEDO WR WKLV ZDUUDQW\ LV DXWKRUL]HG
149 Eileen Way Syosset, New York 11791
www.firstalertpro.com
Copyright © 2003 Honeywell International Inc.
¬.9Vl
K0736-1V1 10/03 Rev. B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement