1000Base-SX / LX to 10/100/1000Base-T 802.3

1000Base-SX / LX to 10/100/1000Base-T 802.3
1000Base-SX / LX to 10/100/1000Base-T
802.3at PoE
Industrial Media Converter
IGTP-802T / IGTP-802TS / IGTP-805AT
User’s Manual
Table of Contents
1. Introduction............................................................................... 5
1.1 Package Contents................................................................ 5
1.2 How to Use This Manual....................................................... 5
1.3 Product Features.................................................................. 6
1.4 Product Specifications.......................................................... 8
1.5 Physical Dimension.............................................................10
2. Installation...............................................................................12
2.1 Product Description.............................................................12
2.1.1 Product Overview.......................................................13
2.1.2 Converter Front Panel.................................................14
2.1.3 LED Indicators...........................................................14
2.1.4 Converter Upper Panel................................................16
2.1.5 Wiring the Power Inputs.............................................16
2.1.6 Wiring the Fault Alarm Contact...................................17
2.2 Mounting Installation...........................................................18
2.2.1 DIN-Rail mounting.....................................................18
2.2.2 Wall Mount Plate Mounting..........................................20
2.2.3 Stand-alone Installation..............................................20
2.2.4 802.3at PoE Installation..............................................23
3. Link Pass Through Function........................................................25
3.1 Link Loss Carry Forward (LLCF)............................................25
3.2 Link Loss Return (LLR)........................................................26
4. Troubleshooting.........................................................................28
5. Cable Connection Parameter.......................................................29
Appendix A: Networking Connection.................................................30
A.1 Switch’s RJ-45 Pin Assignments...........................................30
A.2 RJ-45 cable Pin Assignments...............................................31
Trademarks
Copyright © PLANET Technology Corp. 2011.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or fitness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio
3
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances in
electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
PLANET 1000Base-SX / LX to 10/100/1000Base-T 802.3at PoE
Industrial Media Converter User's Manual
For Models: IGTP-802T / IGTP-802TS / IGTP-805AT
Revision: 1.0 (September, 2011)
Part No: EM-IGTP-80xT_v1.0 (2350-AH1170-000)
4
1.Introduction
1.1 Package Contents
Check the contents of your package for following parts:
uu802.3at PoE Industrial Media Converter x 1
uuUser's Manual x 1
uuDIN Rail Kit x 1
uuWall Mount Kit x 1
If any of these are missing or damaged, please contact your dealer
immediately, if possible, retain the carton including the original packing
material, and use them against to repack the product in case there is a
need to return it to us for repair.
In the following section, the term “Industrial 802.3at PoE Media
Converter” means the IGTP-802T / IGTP-802TS / IGTP-805AT.
1.2 How to Use This Manual
This Industrial 802.3at PoE Media Converter User Manual is
structured as follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical
installation of the Industrial 802.3at PoE Media Converter.
Chapter 3 Link Pass-through
The chapter explains the link pass through function of Industrial
802.3at PoE Media Converter.
Chapter 4 Troubleshooting
The chapter explains the troubleshooting of the Industrial 802.3at PoE
Media Converter.
Chapter 5 Cable Connection Parameters
The chapter explains the cable connection parameters of the Industrial
802.3at PoE Media Converter.
Appendix A
This chapter contains cable information of the Industrial 802.3at PoE
Media Converter.
5
1.3 Product Features
Physical Port
nn 1-Port 10/100/1000Mbps RJ-45 interface, auto-negotiation and autoMDI/MDI-X
uu1-Port Data + Power output, 802.3af / 802.3at PoE standard
compatible
uu10/100/1000Base-T: 1-port Cat. 5/5e/6 UTP cable, up to 100 meters
nn 1-Port Gigabit Fiber Interface
uuIGTP-802T: SC Fiber Interface
uuIGTP-802TS: SC Fiber Interface
uuIGTP-805AT: LC Fiber Interface (Vary on SFP Module 100 / 1000
dual mode support)
Hardware
nn LED Indicators:
uuSystem: Power 1, Power 2 and Fault LED
uuFiber port: LNK / ACT
uu10/100/1000Base-T port: LNK / ACT, PoE In-use
nn DIP-Switch: LFP (Link Fault Pass-through) mode selection
IEEE 802.3af / 802.3at PoE
nn Comply with IEEE 802.3af standard and IEEE 802.3at standard, EndSpan PSE, 1/2(+), 3/6(-)
nn 24V / 48V DC Power Input for PoE
nn Provides DC 52V power over RJ-45 Ethernet cable to devices with
Ethernet port
nn Supports PoE Power up to 30 Watts for PoE port
nn Auto-detect of PoE IEEE 802.3at / IEEE 802.3af equipments,
protecting the devices from being damaged by incorrect installation
nn Remote power feeding up to 100m
6
nn IEEE 802.3at / IEEE 802.3af Splitter devices compatible
Industrial Case / Installation
nn IP-30 Aluminum metal case / Protection
nn DIN Rail and Wall Mount Design
nn 24 and 48V DC, redundant power with polarity reverse protect function and connective removable terminal block for master and slave
power
nn Supports EFT protection 6000 VDC for power line
nn Supports 6000 VDC Ethernet ESD protection
nn -40 to 75 Degree C operating temperature
Standard Compliance
nn IEEE 802.3 10Base-T
nn IEEE 802.3u 100Base-TX / 100Base-FX
nn IEEE 802.3ab 1000Base-T
nn IEEE 802.3z 1000Base-SX / LX
nn IEEE 802.3at Power over Ethernet Standard
nn IEEE 802.3af Power over Ethernet Standard
nn FCC Part 15 Class A, CE
7
1.4 Product Specifications
Model
IGTP-802T
IGTP-802TS
IGTP-805AT
Hardware Specification
10/100/1000Base-T Port
1-Port RJ-45 interface, auto-negotiation and
auto-MDI/MDI-X
1000Base-X Fiber Interface
SC
SC
SFP (LC)
Fiber Cable
Multi-mode:
50/125 µm or
62.5/125 µm
optic fiber
Single-mode:
9/125 µm optic
fiber
Vary on SFP
Module
Cable Distance
220m & 550m
10km
Optical Frequency
850nm
1310nm
Launch Power
Max. -4 dBm
Min. -9.5 dBm
Max. -3 dBm
Min. -9.5 dBm
Receive Sensitivity
-13.5 dBm
-14.4 dBm
Maximum Input power
-18 dBm
-20 dBm
IEEE 802.3at / 802.3af PoE
Port
1, End-Span, 1/2(+), 3/6(-)
LED Indication
System: Power 1, Power 2 and Fault LED (Green)
Fiber port: LNK / ACT (Green)
10/100/1000Base-T port: LNK / ACT, PoE
In-use (Green / Orange)
LFP DIP Switch
ON / OFF
Flow Control
Back pressure for half duplex, IEEE 802.3x Pause
Frame for full duplex
Maximum Frame Size
9216 bytes
Power Requirement
24 and 48V DC, redundant power with polarity
reverse protect function
Enclosure
IP-30 Aluminum metal case
Dimension
135 x 87 x 32mm
Weight
510g
Installation
DIN rail kit and wall mount ear
ESD Protection
6KV DC
EFT Protection
6KV DC
8
Vary on SFP
Module
500g
Alarm
Provides one relay output for power fail
Alarm Relay current carry ability: 1A @ DC 24V
Speed
Twisted-pair: 10/20Mbps for Half / Full-Duplex,
100/200Mbps for Half / Full‑Duplex
1000/2000Mbps for Full‑Duplex
Fiber-optic: 200Mbps / 2000Mbps for Full-Duplex
Network Cables
10/100/1000Base-T:
2-Pair UTP Cat. 3, 4, 5, 5e, 6 (100 meters, max.)
EIA/TIA-568 100-ohm STP (100 meters, max.)
100Base-FX /1000Base-SX / LX:
Multi-mode: 50/125µm or 62.5/125µm optic fiber
Single-mode: 9/125µm optic fiber
Power Consumption
Without PoE:
24V: 4.3 Watts / 14BTU
48V: 4.8 Watts / 16BTU
With PoE:
24V: 33 Watts / 112BTU
48V: 31 Watts / 105BTU
Power over Ethernet
PoE Standard
IEEE 802.3af / 802.3at High Power over Ethernet
/ PSE
PoE Power Supply Type
End-Span
PoE Power Output
52V DC. 15.4 Watts
52V DC. 30 Watts
Power Pin Assignment
1/2(+), 3/6(-)
PoE Budget
30 Watts
Standards Conformance
Standards Compliance
IEEE
IEEE
IEEE
IEEE
IEEE
IEEE
IEEE
802.3 10Base-T Ethernet
802.3u 100Base-TX / FX Fast Ethernet
802.3ab 1000Base-T Gigabit Ethernet
802.3z 1000Base-SX / LX Gigabit Ethernet
802.3x Full-Duplex Flow Control
802.3af Power over Ethernet
802.3at High Power over Ethernet
Stability Testing
IEC60068-2-32 (Free fall)
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
9
1.5 Physical Dimension
IGTP-80xT Industrial 802.3at PoE Media Converter dimension (W x D x
H): 135 x 87 x 32 mm
IGTP-802T / 802TS:
Front View
Side View
Top View
Rear View
Bottom View
Mounting Kit
DIN-Rail Kit
Mounting Kit
10
IGTP-805AT:
Front View
Side View
Top View
Rear View
Bottom View
Mounting Kit
DIN-Rail Kit
Mounting Kit
11
2.Installation
This product provides three different running speeds – 10Mbps, 100Mbps
and 1000Mbps in the same Industrial 802.3at PoE Media Converter
and automatically distinguishes the speed of incoming connection, this
section describes the functionalities of IGTP-80xT’s components and
guides how to install it on the DIN Rail Basic knowledge of networking
is assumed. Please read this chapter completely before continuing.
2.1 Product Description
The Industrial 802.3at High Power over Ethernet Gigabit Media
converter – IGTP-80xT series, fully complies with IEEE 802.3 10Base-T,
IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T and IEEE 802.3z
1000Base-SX / LX, the Gigabit media conversion installation is quite
quick and easy by simple plugging and playing feature. The IGTP80xT series Industrial 802.3at High Power over Ethernet Gigabit Media
converter also supports flow control and back pressure in half-duplex to
eliminate packets loss.
The IGTP-80xT series extends communication distance with highly
Gigabit performance via fiber optical wire, in which the extension
distance could be up to 10km by applying IGTP-802TS and IGTP-805AT
(vary on SFP module) or up to 550m by IGTP-802T, the IGTP-80xT
series is specifically designed with durable components and strong
housing case to operate reliably in electrically harsh and climatically
demanding environments. The industrial level Gigabit media converter
provides a high level of immunity to electromagnetic interference and
heavy electrical surges which are usually found on plant floors or
traffic control cabinets in sidewalk. Being able to operate under the
temperature range from -40 to 75 Degree C allow the IGTP-80xT series
can be placed in almost any difficult environment.
The maximum distance between the PoE PSE to PD is 100 meters. To
extend the network device deployment range, the IGTP-80xT series is
integrated with Fiber interface. The IGTP-80xT series is used to convert
optical Ethernet signal to electrical Ethernet signal that allows two type
segments to connect easily, efficiently and inexpensively. It can convert
10/100/1000Base-T signal to 1000Base-SX / LX one and provides the
diverse options of fiber connecting types to meet different network
applications.
12
With the long Fiber distance support, it still sustains the transmission
performance as high as 1000Mbps. It works in high performance Store
and Forward mechanism, and also can prevent packet loss with IEEE
802.3x Flow Control (Full-Duplex) and the LFP (Link Fault Pass Through
function) (LLCF/LLR) with the DIP Switch design. Furthermore, it can
immediately alarm the administrators the issue from the link media and
provide efficient solution to monitor the network power usage.
To fill the growing demand of Industrial PoE PD devices those need
higher Power Input and long distance transmission, the IGTP-80xT
series Industrial 802.3at High Power over Ethernet Gigabit Media
converter with brand-new IEEE 802.3at High Power over Ethernet
technology applied. The IGTP-80xT provides the following key features:
uuIEEE 802.3at Power over Ethernet standard compliant
uuIEEE 802.3af Power over Ethernet standard
uuMaximum 30 Watts output power support
uu10/100/1000Mbps duplex mode support on 1000Base-T port
uu1000Mbps Fiber-Optical support on IGTP-802T / IGTP-802TS
uu100Mbps / 1000Mbps Fiber-Optical support on IGTP-805AT
The IGTP-80xT series is a Single-Port, End-Span Industrial IEEE 802.3at
High Power over Ethernet Gigabit Media converter with maximum
up to 30 Watts of power output over Ethernet cables. It is designed
specifically to satisfy the growing demand of higher power required
network equipments such as PTZ (Pan, Tilt & Zoom) network cameras,
PTZ Speed Dome, color touch-screen / Video and Voice over IP (VoIP)
telephones, multi- channel (11a / b / g / n) wireless LAN access points
and other Network devices that need higher power to function normally.
The IGTP-80xT series Industrial 802.3at High Power over Ethernet
Gigabit Media converter is an ideal solution to deliver data and power
to network devices directly via the RJ-45 Port interface without the
need of installing extra power outlets and electrical cabling.
2.1.1 Product Overview
The Front Panel of the Industrial 802.3at PoE Media Converter consists
of one 1000Base-SX / 1000Base-LX / mini-GBIC SFP ports and one
Auto-Sensing 10/100/1000Mbps Ethernet RJ-45 Port. Figure 2-1, 2-2
shows a front panel of Industrial 802.3at PoE Media Converter.
13
2.1.2 Converter Front Panel
Figure 2-1 & 2-2 shows a front panel of Industrial 802.3at PoE Media
Converter.
Figure 2-1:
IGTP-802T/ 802TS Front Panel
Figure 2-2:
IGTP-805AT Front Panel
2.1.3 LED Indicators
System:
LED
Color
Function
P1
Green
Lit: indicate the power 1 has power.
P2
Green
Lit: indicate the power 2 has power.
FAULT
Green
Lit: indicate the either power 1 or power 2 has no
power.
14
Gigabit Fiber Interface
LED
Fiber
LNK/
ACT
Color
Green
Function
Lit: indicate that the Fiber Optical Port is
successfully connecting to the network at
1000Mbps.
Blinks: indicate the Fiber Optical Port is receiving or
sending data.
Gigabit TP Interface
LED
Color
Function
Lit: indicate that the Gigabit Ethernet Port is
successfully connecting to the network at
10/100/1000Mbps.
TP
LNK/
ACT
Green
Blinks: indicate the Gigabit Ethernet Port is
receiving or sending data.
Lit: indicate that the Gigabit Ethernet Port is
successfully connecting to the network at
1000Mbps. OFF indicate the Gigabit Ethernet
Port is successfully connecting to the network at
10/100Mbps.
TP
1000
PoE
LED
Color
Function
Lit: Indicate that the port is providing DC 52V to
remote powered device.
PoE
Orange
In-Use
Off: Indicate that the port is not providing DC 52V
to remote powered device.
15
2.1.4 Converter Upper Panel
The upper panel of the Industrial 802.3at PoE Media Converter consist
one terminal block connector within two DC power inputs. Figure 2-3
shows the upper panel of the Industrial 802.3at PoE Media Converter.
DC 24V/48V
Figure 2-3: Industrial 802.3at PoE Media Converter upper Panel.
2.1.5 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial
802.3at PoE Media Converter is used for two DC redundant powers
input. Please follow the steps below to insert the power wire.
1.Insert positive / negative DC power wires into the contacts 1 and 2
for POWER 1, or 5 and 6 for POWER 2.
DC 24V/48V
16
V1- V1+
V2- V2+
2.Tighten the wire-clamp screws for preventing the wires from loosing.
1
2
Power 1
+
Note
3
Fault
4
5
6
Power 2
+
The wire gauge for the terminal block should be in the
range between 12 ~ 24 AWG.
2.1.6 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the
Industrial 802.3at PoE Media Converter will detect the fault status of
the power failure, or port link failure (available for managed model)
and then forms an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts.
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in
the range between 12 ~ 24 AWG.
2. Alarm relay circuit accepts up to 30V, max. 3A
currents.
17
2.2 Mounting Installation
This section describes how to install the Industrial 802.3at PoE Media
Converter and make connections to it. Please read the following topics
and perform the procedures in the order being presented.
Note
In the installation steps below, this Manual use IGS801(PLANET 8 Port Industrial Gigabit Switch) as the
example. However, the steps for PLANET Industrial
Switch & Industrial Media / Serial Converter are similar.
Terms of “Industrial Equipment” in following section
means the PLANET Industrial devices that mentioned
above.
2.2.1 DIN-Rail mounting
The DIN-Rail is screwed on the Industrial Equipment when out of
factory. When need to replace the wall mount application with DIN-Rail
application on Industrial Equipment, please refer to following figures to
screw the DIN-Rail on the Industrial Equipment. To hang the Industrial
Equipment, follow the below steps:
Step 1: screw the DIN-Rail on the Industrial 802.3at PoE Media
Converter
18
1
2
Step 2: Lightly press the button of DIN-Rail into the track.
Step 3: Check the DIN-Rail is tightly on the track.
Step 4: Please refer to following procedures to remove the Industrial
802.3at PoE Media Converter from the track.
1
2
Step 5: Lightly press the button of DIN-Rail for remove it from the
track.
19
2.2.2 Wall Mount Plate Mounting
To install the Industrial 802.3at PoE Media Converter on the wall, please
follows the instructions described below.
Step 1: Remove the DIN-Rail from the Industrial 802.3at PoE Media
Converter; loose the screws to remove the DIN-Rail.
Step 2: Place the wall mount plate on the rear panel of the Industrial
802.3at PoE Media Converter.
Step 3: Use the screws to screw the wall mount plate on the
Industrial 802.3at PoE Media Converter.
Step 4: Use the hook holes at the corners of the wall mount plate to
hang the Industrial 802.3at PoE Media Converter on the wall.
Step 5: To remove the wall mount plate, reverse steps above.
2.2.3 Stand-alone Installation
IGTP-802T / IGTP-802TS/ IGTP-805AT Installation:
To install an Industrial 802.3at PoE Media Converter stand-alone, on a
Track or wall mount, simply complete the following steps:
Step 1: Turn off the DC power of the device/station in a network to
which IGTP-802T / IGTP-802TS will be attached.
Step 2: Ensure that there is no activity in the network.
Step 3: Attach fiber cable from the Industrial 802.3at PoE Media
Converter to the fiber network. TX, RX must be paired at
both ends.
20
Step 4: Connect the DC power to the IGTP-802T / IGTP-802TS and
verify that the Power LED lights up.
Step 5: Turn on the power of the device/station; the PWR LED
(Green) should light when all cables are attached.
DC 24V / 48V
LOCATION A
1000Base-SX/LX
Fiber Switch
SFP Module
RJ-45
PoE IP Camera
LOCATION B
IGTP-802T/IGTP-802TS
Figure 2-4: IGTP- 802T / IGTP-802TS Stand-alone Installation
Note
Please refers to APPENDIX-A for detailed wiring information of the Industrial 802.3at PoE Media Converter.
To prevent from optic acceptor malfunction, check the
both wires / transmitter before power on the Industrial
802.3at PoE Media Converter.
IGTP-805AT Installation:
IGTP-805AT is with high reliability and flexibility to extend the distance
from 220m to 120Km. It depends on the 100M / 1000M mini GBIC
modules. The SFP transceivers are hot-plug and hot-swappable. You can
plug-in and out the transceiver to/from any SFP port without having to
power down the Industrial 802.3at PoE Media Converter.
To install IGTP-805AT with 100Base-FX, 1000Base-SX / LX SFP, simply
complete the following steps:
Step 1: Precede with the steps 4 and steps 5 of session 2.2.3 Standalone Installation to connect the network cabling and
supply power to your Industrial Managed Media Converter.
21
Step 2: Slot in the 100Base-FX, 1000Base-SX / LX SFP. Make sure
both side of the SFP transceiver are with the same media
type, for example: 100Base-FX / 2km to 100Base-FX / 2km,
1000Base-SX / 220m & 550m to 1000Base-SX / 220m &
550m, 1000Base-LX / 10km to 1000Base-LX / 10km.
Step 3: Connect the fiber cable. Attach the duplex LC connector on
the network cable into the SFP transceiver.
DC 24V / 48V
LOCATION A
100/1000X
Fiber Switch
SFP Module
SFP Module
RJ-45
PoE IP Camera
IGTP-805AT
LOCATION B
Figure 2-5: IGTP- 805AT Stand-alone Installation
Note
It recommends using PLANET MFB / MGB series
100Base-FX / 1000Base-SX / LX / LX WDM SFP on the
IGTP-805AT. If you insert a SFP transceiver that is not
supported, the IGTP-805AT will not recognize it.
The following list the available Modules for IGTP-805AT
MGB-GT
SFP-Port 1000Base-T Module
MGB-SX
SFP-Port 1000Base-SX mini-GBIC module - 550m
MGB-LX
SFP-Port 1000Base-LX mini-GBIC module - 10km
MGB-L30
SFP-Port 1000Base-LX mini-GBIC module - 30km
MGB-L50
SFP-Port 1000Base-LX mini-GBIC module - 50km
MGB-L70
SFP-Port 1000Base-LX mini-GBIC module - 70km
MGB-L120 SFP-Port 1000Base-LX mini-GBIC module - 120km
MGB-LA10
22
SFP-Port 1000Base-LX (WDM, TX:1310nm) mini-GBIC
module - 10km
MGB-LB10
SFP-Port 1000Base-LX (WDM, TX:1550nm) mini-GBIC
module - 10km
MGB-LA20
SFP-Port 1000Base-LX (WDM, TX:1310nm) mini-GBIC
module - 20km
MGB-LB20
SFP-Port 1000Base-LX (WDM, TX:1550nm) mini-GBIC
module - 20km
MGB-LA40
SFP-Port 1000Base-LX (WDM, TX:1310nm) mini-GBIC
module - 40km
MGB-LB40
SFP-Port 1000Base-LX (WDM, TX:1550nm) mini-GBIC
module - 40km
MGB-TLX
SFP-Port 1000Base-LX mini-GBIC module - 10km
(-40~75 Degree C)
MGB-TSX
SFP-Port 1000Base-SX mini-GBIC module - 550m
(-40~75 Degree C)
MGB-TL30
SFP-Port 1000Base-LX mini-GBIC module - 30km
(-40~75 Degree C)
MGB-TL70
SFP-Port 1000Base-LX mini-GBIC module - 70km
(-40~75 Degree C)
MFB-FX
SFP-Port 100Base-FX Transceiver (1310nm) - 2KM
MFB-F20
SFP-Port 100Base-FX Transceiver (1310nm) - 20KM
MFB-F40
SFP-Port 100Base-FX Transceiver (1310nm) - 40KM
MFB-F60
SFP-Port 100Base-FX Transceiver (1310nm) - 60KM
MFB-FA20
SFP-Port 100Base-BX Transceiver (WDM, TX:1310nm)
- 20KM
MFB-FB20
SFP-Port 100Base-BX Transceiver (WDM, TX:1550nm)
- 20KM
MFB-TFX
SFP-Port 100Base-FX Transceiver (1310nm) - 2km
(-40~75 Degree C)
MFB-TF20
SFP-Port 100Base-FX Transceiver (1310nm) - 20km
(-40~75 Degree C)
2.2.4 802.3at PoE Installation
IGTP-802T / IGTP-802TS/ IGTP-805AT Installation:
IGTP-80xT and the IEEE 802.3at / 802.3af Injector installation:
Before your installation, it is recommended to check your network
23
environment. If there is any IEEE 802.3at / 802.3af devices need to
power on, the IGTP-80xT can provide you a way to supply power for
this Ethernet device conveniently and easily.
The IGTP-80xT need DC 52V input and it injects the DC power into the
pin of the twisted pair cable (Pin 1, 2, 3 and 6).
550m / 10km
100 meters
48V DC Output
DC
Industrial DIN Rail
Power Supply
AC
Data
IGTP-802T/
IGTP-802TS
Power
Data
1000
PoE
Fiber Switch
PoE+
Speed Dome
550m / 10km
100 meters
48V DC Output
DC
Industrial DIN Rail
Power Supply
AC
Data
IGTP-805AT
Data
1000
Power
PoE
Fiber Switch
PoE+
Speed Dome
1000
24
1000Base-SX/LX Fiber-optic
PoE
1000Base-T UTP with PoE
AC
Power Line (AC)
DC
Power Line (DC)
3.Link Pass Through Function
The LFP function includes the Link Fault Pass Through function (LLCF/
LLR) and the DIP Switch design. LLCF/LLR can immediately alarm
administrators the problem of the link media and provide efficient
solution to monitor the net. The DIP Switch provides disable or enable
the LFP function.
LLCF (Link Loss Carry Forward) means when a device connected to
the converter and the TP line loss the link, the converter’s fiber will
disconnect the link of transmit. LLR (Link Loss Return) means when
a device connected to the converter and the fiber line loss the link,
the converter’s fiber will disconnect the link of transmit. Both can
immediately alarm administrators the problem of the link media and
provide efficient solution to monitor the net.
3.1 Link Loss Carry Forward (LLCF)
The IGTP-80xT incorporates default LLCF function for troubleshooting a
remote connection; the Fiber/TP ports do not transmit a link signal until
they receive a link signal from the opposite port.
The diagram below shows a typical network configuration with a good
link status using IGTP-80xT for remote connectivity.
Management
Station
Switch/Hub
w/SNMP
Media
Converter
Media
Converter
LFP ON
l LED lit = established link
Management
Station
Switch/Hub
w/SNMP
Switch/Hub
w/SNMP
Management
Station
TP
° LED unlit = no link
Media
Converter
Media
Converter
LFP ON
TP
Management
Station
LFP ON
Fiber
Cable
TP
Switch/Hub
w/SNMP
LFP ON
Broken
Fiber
Cable
TP
25
If the connection breaks, IGTP-80xT that link loss forward to the
switch/hub which generates a trap to the management station. The
administrator can then determine the source of the issue.
Management
Station
Switch/Hub
w/SNMP
Media
Converter
Media
Converter
LFP ON
TP
l LED lit = established link
Switch/Hub
w/SNMP
Management
Station
LFP ON
Fiber
Cable
TP
° LED unlit = no link
The converter is shipped with the default LFP (LLCF/
LLR) function disable. This feature can also be turned
on on-purpose. If you are familiar with the network
installation and for diagnostic purpose (i.e. check which
end is broken), you can turn it on and the converter will
Note
Management Switch/Hub
Media
Switch/Hub Management
Media
Station takew/SNMP
Converter
w/SNMP remains
Station it in
Converter
effect immediately.
Otherwise,
please
the default position.
LFP ON
LFP ON
TP
Broken
Fiber
Cable
TP
3.2 Link Loss Return (LLR)
l LED lit = established link
° LED unlit = no link
The fiber ports of IGTP-80xT have been designed with an LLR function
for troubleshooting a remote connection. LLR works in conjunction with
LLCF.
When LLR
its receiver
enabled on
unmanaged
is enabled*, the port’s transmitter shuts down when
fails to detect a valid receive link. LLR should only be
one end of the link and is typically enabled on either the
or remote device.
The diagram below shows a typical network configuration with a good
link status using IGTP-80xT for remote connectivity. Note that LLR is
enabled as indicated in the diagram.
26
Management
Station
Switch/Hub
w/SNMP
Media
Converter
Media
Converter
LFP ON
Switch/Hub
Station
LFP OFF
Fiber
Cable
l LED lit = established link
° LED unlit = no link
If one of the optical conductors is bad (as shown in the diagram box
below), the converter with LLR enabled will return a no-link condition
to its link partner. With LLCF also default enabled, the no-link condition
is carried forward to the switch/hub where a trap is generated to the
management station, and the administrator can then determine the
Management Switch/Hub
Media
Management
Media
Station
Station
w/SNMP
Converter
Switch/Hub
Converter
source of
the loss.
LFP ON
Management
Station
Switch/Hub TP Media
w/SNMP
Converter
Port
2
LFP ON
Broken
Fiber
Media TP
Switch/Hub
Converter
Port 1
Station
Link Loss Carried Forward
LFP ON
LinkOFF
Loss Carried Forward
LFP
Link Loss Returned
Fiber
Cable
l LED lit = established link
° LED unlit = no link
l LED lit = established link
° LED unlit = no link
The converter is shipped with the default LFP (LLCF/
LLR) function disable. This feature can also be turned on
on-purpose. If you are familiar with the network installation and for diagnostic purpose (i.e. check which end is
Management Switch/Hub
Media
Management
Media
w/SNMP youConverter
Converter
Switch/Hub
can turn it on
and the
converterStation
will take
NoteStation broken),
effect immediately. Otherwise, please remains it in the
LFP ON
LFP ON
default position.
Broken
Fiber
TP
TP
Port 2
Port 1
Link Loss Carried Forward
Link Loss Carried Forward
Link Loss Returned
l LED lit = established link
° LED unlit = no link
27
4.Troubleshooting
This chapter contains information to help you solve issues. If the IGTP80xT is not functioning properly, make sure the IGTP-80xT was set up
according to instructions in this manual.
The Power LED is not lit
Solution:
Check the power cable connection between power adapter and IGTP80xT.
Why I connect IGTP-80xT to device with 1000Base-LX/SX
interface and the 1000Base-LX/SX fiber connection fail?
Solution:
Please check the fiber connection between two devices is correct.
10/100/1000Base-T port link LED is lit, but the traffic is irregular
Solution:
1.Check that the attached device is not set to dedicate full duplex.
Some devices use a physical or software switch to change duplex
modes. Auto-negotiation may not recognize this type of full-duplex
setting.
2.Check and assure the TP ports from both IGTP-80xT and attached
device run at Auto-negotiation mode.
Why the PoE port not provide power to my powered devices?
Solution:
Since the IGTP-80xT comply with IEEE 802.3at / 802.3af PoE standard,
please check that the device is also comply with IEEE 802.3at / 802.3af
PoE standard. Otherwise, the IGTP-80xT will not inject PoE power to
the devices.
Why I connect IGTP-805AT to device with 100Base-FX
interface and the 100Base-FX fiber connection fail?
Solution:
Please check the fiber connection between two devices is correct.
28
5.Cable Connection Parameter
The wiring details are as below:
100FX Fiber Optical Cables:
Standard
Fiber Type
Cable Specification
100Base-FX (1300nm)
Multi-mode
50/125μm or 62.5/125μm
Multi-mode
50/125μm or 62.5/125μm
Single-mode
9/125μm
Single-mode
9/125μm
100Base-FX (1310nm)
100Base-BX-U
(TX: 1310/RX: 1550)
100Base-BX-D
(TX: 1550/RX: 1310)
1000X Fiber Optical Cables:
Standard
Fiber Type
Cable Specification
1000Base-SX (850nm)
Multi-mode
50/125μm or 62.5/125μm
Multi-mode
50/125μm or 62.5/125μm
Single-mode
9/125μm
1000Base-LX (1300nm)
Wiring Distances:
Standard
1000Base- SX
1000Base- LX
Note
Fiber
Diameter
(micron)
Modal Bandwidth
(MHz * km)
Max. Distance
(meters)
MM
62.5
62.5
50
50
100
200
400
500
220
275
500
550
62.5
50
50
5
4
5
550
MM
SM
9
N/A
5000*
The Single-mode port (1000Base-LX port) of IGTP-802TS,
IGTP-805AT is complied with LX 5 kilometers and provides
additional margin allowing for a 10/20/30/40/50/70/120
kilometers Gigabit Ethernet link on single mode fiber.
29
Appendix A: Networking Connection
A.1 Switch’s RJ-45 Pin Assignments
1000Mbps, 1000Base-T
Contact
MDI
MDI-X
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
10/100Mbps, 10/100Base-TX
RJ-45 Connector pin assignment
Contact
MDI Media Dependant
Interface
MDI-X Media Dependant
Interface -Cross
1
Tx + (transmit)
Rx + (receive)
2
Tx - (transmit)
Rx - (receive)
3
Rx + (receive)
Tx + (transmit)
4, 5
6
7, 8
30
Not used
Rx - (receive)
Tx - (transmit)
Not used
A.2 RJ-45 cable Pin Assignments
The standard RJ-45 receptacle/connector
There are 8 wires on a standard UTP/STP cable and each wire is colorcoded. The following shows the pin allocation and color of straight cable
and crossover cable connection:
Straight Cable
1 2 3 4 5 6 7 8
SIDE 1
1 2 3 4 5 6 7 8
SIDE 2
Crossover Cable
1 2 3 4 5 6 7 8
SIDE 1
1 2 3 4 5 6 7 8
SIDE 2
SIDE 1
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
SIDE 2
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
SIDE 1
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
SIDE 2
1 = White/Green
2 = Green
3 = White/Orange
4 = Blue
5 = White/Blue
6 = Orange
7 = White/Brown
8 = Brown
Figure A-1: Straight-Through and Crossover Cable
Please make sure your connected cables are with same pin assignment
and color as above picture before deploying the cables into your
network.
31
EC Declaration of Conformity
For the following equipment:
*Type of Product:
*Model Number:
1000Base-SX/LX to 10/100/1000Base-T 802.3at PoE Media Converter
(-40~75 Degree C)
IGTP-802T、IGTP-802TS、IGTP-805AT
* Produced by:
Manufacturer‘s Name :
Manufacturer‘s Address:
Planet Technology Corp.
10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022
EN 61000-3-2
EN 61000-3-3
EN55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
(2006 + A1:2007)
(2006 + A2:2009)
(2008)
(1998 + A1:2001 + A2:2003)
(2008)
(2006 + A1:2007 + A2:2010)
(2004 + A1:2010)
(2005)
(2008)
(2009)
(2004)
Responsible for marking this declaration if the:
 Manufacturer
 Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan
Place
14th Oct., 2011
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected]
http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement