NTD36HD Manual


Add to my manuals
73 Pages

advertisement

NTD36HD Manual | Manualzz
Federal Communication Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions :
This device may not cause harmful interference
This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the Federal Communication Commission(FCC) rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and , if not installed and used in accordance with the instructions, may
cause harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/television technician for help.
CAUTION! Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the user’s
authority to user’s authority to operate the euipment.
Canadian Department of Communications
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio interference Regulations of the Canadian Department
of Communications.
Hereby, NOVATRON, declares that this product is compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
CONTENTS
1
2
3
Introduction ··························································
4
Multimedia Functions······························································
4
Input/Output Functions····························································
5
Kinds of format to be supported··················································
6
TV Out set-up and change·······················································
7
Precautions·········································································
8
How to handle and other precautions············································
9
Name of each point – Top & Front···············································
10
Name of each point – Rear side··················································
11
Contents in package·······························································
12
Accessories available at shops··················································
13
Preparation to use NTD36HD ·····································
14
Procedure···········································································
14
Kinds of HDD to be installed······················································
14
HDD Installation····································································
15
Connecting with PC································································
16
To create folder and to copy files·················································
17
Disconnecting from PC····························································
18
Connecting to TV with Composite(AV) cable···································
19
Connecting with Component cable or DVI connector··························
20
Connecting with 5.1CH audio system···········································
21
Connecting with Optical or Coaxial connector··································
22
Connecting to Network····························································
23
Remote Controller & SET-UP Menu·······························
24
Structure of Remote Controller···················································
24
Booting Message & Main Menu··················································
25
Review of each Icon on Main Menu············································
26
SETUP Menu and How to set up·················································
27
VIDEO setting change·····························································
28
AUDIO setting change·····························································
29
ETC(Other) settings································································
30
NETWORK setting·································································
31
WIRELESS (Auto setting)························································
32
WIRELESS (Manual setting) ····················································
34
WIRELESS (AD-HOC setting)····················································
37
LAN Sharing setting(PC) ·························································
39
Network configuration under window 2000······································
40
IP Address Setup: Ethernet Network using a direct connection··············
45
MULTIMEDIA FILE PLAYBACK ···································
47
How to use JUKEBOX CREATOR(BGM ON) ·································
47
Enjoying movie file·································································
48
Creating DVD Library and Enjoying it············································
55
Enjoying Music Library····························································
57
Enjoying Photo Library····························································
58
External USB devices connection················································
59
5
Firmware update ·····················································
60
6
HDD Partition and Formatting ····································
61
Under Window 98SE/ME environment··········································
61
Under Window 2000/XP environment···········································
65
A
Troubleshooting ·····················································
69
B
SPECIFICATION·······················································
73
4
Introduction
To introduce features and functions of NTD36HD.
Multimedia Functions
To playback a recorded digital HD file
As NTD36HD supports up to 1920 x 1080 progressive scan, you can enjoy playing back
a pre-recorded HDTV program by a digital TV set-top box or person digital video
contents taken by a HD camcorder with fantastic displaying quality.
To support various video formats
NTD36HD supports various latest video formats such as a pre-recorded HD file(tp, ts),
WMV9, WMV9 HD, MPEG1/2, MPG, MPEG4(DivX, Xvid), etc.
DVD JUKE BOX Function
As NTD36HD supports ISO file and IFO file, you can store DVD titles into NTD36HD
and playback those files just like DVD Player. You can store various DVD titles into
NTD36HD and manage them forever and easily.
Auto Playback, Bookmark and Section Repeat Functions
After one file playback is ended, the next file(different in file name only) is play-backed
automatically. If you mark a specific position of a movie during playback with
“BOOKMARK” button of remote controller, you can start from the marked position again.
The function of ‘Section Repeat’ lets you repeat a specific section. Section Repeat
function is useful for language study or enjoying sports moving pictures.
Music JUKE BOX Function
As NTD36HD supports various music files like MP3, Ogg Vorbis, WMA, M3U and PLS,
you can store these files into NTD36HD and enjoy them with easy. And, in case that you
make NTD36HD’s own playlist by using ‘JUKE BOX CREATOR’ function, you can enjoy
music files(playlisted) as background music(BGM function) with easy and convenient.
Digital Photo Album
You can enjoy photo with NTD36HD together with your family through big screen of TV
in your living room, as NTD36HD has ‘Photo Slide Show’ and ‘BGM(Background Music)’
functions.
4
Input/Output Functions
Analog 5.1CH Audio Output and 2CH Down Mix
NTD36HD can output analog audio signal(decoded signal), as it can decode digital
signal(high quality audio sound signal like AC3, DTS) into analog signal internally by
itself. So, you can enjoy 5.1CH high quality sound without an expansive additional
device like DTS decoder or Receiver. And, as NTD36HD supports 2CH down mix, users
who have 2CH speaker only also can enjoy multi channel audio track..
High Quality DVI Connector
As NTD36HD has DVI connector which output high quality digital signal, you can enjoy
high quality display without any display distortion.
Streaming through Wired/Wireless Network
Without the procedure to copy files from PC to NTD36HD through USB cable, you can
stream various media files in your PC to NTD36HD and playback them back with TV
directly through NTD36HD’s Network solution.
Installed Wireless LAN Module and Antenna
As NTD36HD has Wired LAN as well as Wireless LAN module which supports turbo
function, WEP security function and high sensitive 5dBi antenna, you can connect
NTD36HD easily with any wireless network environment.
HOST USB2.0 lets you connect with various external USB devices
As NTD36HD has two(2) USB2.0 HOST, you can attaché various external USB devices
such as external HDD, USB memory, digital camera, etc.
External Mass Storage
As NTD36HD works perfectly as an external USB mass-storage for your PC through
high speed USB2.0, you can store huge data into NTD36HD and manage it with easy.
5
Kinds of format to be supported
Video
HD file format(tp,ts), Windows Media 9, Windows Media 9 HD
DivX3.11, DivX4, DivX5, DivX HD, Xvid, MPEG1, MPEG2(IFO, VOB, ISO)
Subtitle
SMI, SUB, SRT
Audio
MP3, Ogg Vorbis, WMA, AC3, DTS
Picture
JPEG, BMP, PNG
Needed minimum transferring rate
Format
Wired, Wireless LAN
USB2.O(HOST)
MPEG1/2
12Mbps
10Mbps
DivX, Xvid
1.5Mbps
1.5Mbps
WMV9
8Mbps
8Mbps
• Even though a video file format is corresponding to the above table, the video file may
not be played-back properly in case that the resolution and transferring rate of the
video file is over specific value.
• Although a video file format is corresponding to the above table, the video file may not
be played-back properly according to the speed(performance) of external USB devices
or the speed(performance) of the devices to compose a network environment.
• Even though video file format is one of the above classification, the file is not played if
the file is encoded with GMC or QPEL option.
• AVI(Audio Video Interleaved) is a container format. This means that it may contain
many different combinations of codec. So, even if NTD36HD supports most of AVI files,
but, there could be AVI files not played back properly by NTD36HD.
• Subtitle is supported properly in case only that the file name of subtitle is exactly same
as that of the moving picture.
• The audio file encoded with copy protection technology is not played back properly.
• Even if NTD36HD can playback 2048 x 1352(JPEG), it may not work properly if the
JPEG size is over 1920 x 1080.
6
TV OUT set-up and change
TV Standard for each country
Korea, North America
Europe and else
NTSC
PAL
※ TV out mode is originally set as PAL/Composite
※ If you want to change TV out mode, you can use TV OUT button of remote controller or TV OUT button
of the front side of NTD36HD set.
※ LED light of the front side of NTD36HD moves to corresponding position when you press TV OUT button
with 2~3sec time interval.
LED of NTD36HD Front
TV OUT button for changing TV Out mode
AUDIO OUT button for changing
AUDIO Out mode
Reference
※ Each pressing TV OUT button : PAL(Composite)
480p(Component)
576p(Component)
576p DVI-D ( DVI-A VGA 800x600 60Hz (NTSC(Composite)
You can change and select more subdivided TV out mode in SET UP menu
In case of no display on TV screen, try pressing TV OUT button several times to fit TV OUT mode
AUDIO OUT button does not work while movie is playing.
480p DVI-D
7
Precautions
Do not drop or give a shock. It may cause
Do not block a ventilation opening
serious damage to internal Hard Disk Drive.
Keep it away from high temperature, high
humidity, nearby magnetic filed and direct
Do not touch the plug of the AC power cord
sunlight.
with wet hands
Do not try disassembling. It may cause an
electric shock, defect or unexpected problem.
Keep it unplugged during lightning storms or
For installing or changing HDD, you may open
when unused for long period time.
the door on bottom side.
8
How to handle and other precautions
•
Make sure that you have to use the AC adapter supplied together with NTD36HD. If not,
it may cause unexpected problem like breakdown, fire, etc.
•
In case that NTD36HD is used or left in a completely covered and high temperature
space(like in a car) for long time, it may cause unexpected problem.
•
Do not see the light of OPTICAL connector directly. It may have a bad effect on your
eyes.
•
In case of no use for long time, get rid of battery from remote controller.
•
To clean the exterior of NTD36HD, soak a soft cloth in a mild detergent solution diluted
with water, tightly squeeze the cloth to remove the excess liquid, wipe the affected area
of the exterior, and finish by wiping with a dry cloth.
•
Make sure that NTD36HD is not powered off suddenly during its working(playing-back,
file transferring, firmware upgrading, etc). In case of sudden power-off during working,
you need to check HDD with Windows utility(Scan Disk) after connecting with your PC
system.
•
When you try disconnecting the USB cable between NTD36HD and your PC system
after finishing jobs, make sure to follow ‘USB device safety removal’ procedure.
•
When try connecting HDD to SATA cable, S-Video cable, DVI cable, be careful not to
give some damage to pins of each connector.
9
Name of each point – Top & Front
Button of top side
Power(On/Off) Button
SETUP Button
OK BUTTON
STOP Button
PLAY/PAUSE BUTTON
Direction,
REW/FWD and
+15/-15sec move
Button
(▲, ▼, ◀, ▶)
Button & LED of front side
IR receiver
TV OUT Button
Video / S-Video or
Component(DVD) LED
DTV Component LED
DVI-D LED
DVI-A LED
AUDIO OUT Button
2CH Stereo Audio out LED
Analog 5.1CH
Audio out LED
Digital Sound out LED
Wired/Wireless
USB Host Connection
Connection Status LED
Status LED
Power LED
HDD LED
PLAY LED
10
Name of each point – Rear Side
External IR receiver
Connector
For Wireless Antenna
USB connector
for PC
S-Video
DC FAN
Digital Sound
Optical Connector
DVI Out connector
Digital Sound
Coaxial Connector
Composite
Video Connector
2CH Stereo
or
5.1CH Analog
Audio Connector
Component Video
Connector
Wired LAN
Port(RJ-45)
USB Host port
Power12V DC
11
Contents in package
Below items are in the package of NTD36HD
□ NTD36HD
User’s Manual
□ A to B USB Cable
□ Remote Controller
□ AAA size Batteries
□ 12V DC Power Adaptor
□ Power cord
□ Composite A/V Cable
□ Component Video Cable
□ 5dBi Wireless Antenna
(Wireless model only)
12
Accessories available at shops
If below accessories needed, you can buy them at shops by yourself.
DVI to RGB Gender
DVI to HDMI Gender
DVI-I Cable
Coaxial Cable
Optical Cable
S-VIDEO Cable
LAN Cable
13
Preparation to use NTD36HD
To introduce preparation before you enjoy NTD36HD.
Procedure
1. Check whether all accessories are supplied properly.
2. Install HDD(Hard Disk Drive) into NTD36HD according to the procedure of HDD
installation(※ note : HDD jumper should be set as Master)
3. Connect AC adapter into NTD36HD, and connect NTD36HD with PC through USB
cable
4. Power on NTD36HD(with power button of top side, or with power button of remote
controller)
5. In case that the installed HDD is not formatted, please format it first according to
normal HDD format procedure
6. Copy media files in your PC to the HDD of NTD36HD
7. After finishing copying files, disconnect NTD36HD from your PC system
8. Connect NTD36HD to TV set and(or) to audio system
9. Power on NTD36HD and change set-up value in SET-UP menu if needed. It is
recommended that NTD36HD should be rebooted if you set up Network newly
10. Now, you are ready to enjoy NTD36HD freely
Kinds of HDD to be installed
HDD Size
HDD Type
HDD Capacity
HDD RPM
HDD buffer
Memory
3.5” SATA HDD
SATA I or II
Any capacity
available in market
Over 7200 RPM
Over 8M
14
HDD Installation
1. Push the locker to the direction(“OPEN
).
2. There is HDD fixture inside. Push it
forward(#1) slightly and pull it up(#2).
Open up the HDD door slowly.
4. Fix HDD with HDD fixture like below picture.
3. . Insert HDD carefully inside with NTD36HD
laid down slightly to minimize impact to HDD.
5. Connect SATA cable and power cable
6 Close HDD door and push the locker to the
direction(“
like picture.
POWER
IDE
15
CLOSE”).
Connecting with PC
To copy files in your PC to NTD36HD, follow below procedure.
For Windows ME/ 2000/XP Users
1. Power on your PC system.
2. Connect NTD36HD to your PC with USB Cable. Connect AC adapter to NTD36HD. And power it
on.
3. Wait until your PC recognizes NTD36HD as USB mass storage.
4. Check whether NTD36HD is properly recognized as USB mass storage by clicking and opening
“My Computer” on Windows.
For Windows 98SE Users
1. Before connecting NTD36HD to your PC, you need to install Driver for Windows 98SE to your
PC. You may download the Driver for Windows 98SE from our website(www.iamm.co.kr)
2. After downloading it, unzip it and run the file(NTD36HD_98setup)
3. Connect NTD36HD to your PC with USB cable. And connect AC adapter to NTD36HD and
power it on. Wait until your PC recognizes NTD36HD as USB mass storage.
4. Check whether NTD36HD is properly recognized as USB mass storage by clicking and
opening “My Computer” on Windows.
16
To create folder and to copy files
Follow below procedure to copy folder and file from PC to NTD36HD.
• If the HDD has no partition or the HDD is not formatted, you need to do it first.
-
We recommend NTFS instead of FAT32. NTD36HD supports multi partitions.
-
Note : Primary partition should be over one(1)
※ For HDD partition, refer to Chapter 6.
• When you make folder in the HDD of NTD36HD, it is recommended that you make
folders like ‘MOVIE’, ‘MUSIC’, ‘PHOTO’. And, you copy files to each folder
corresponding to kind of file.
- ‘MOVIE’ folder responds to ‘MOVIE’ button of remote controller and ‘MOVIE’ icon of main
menu.
- ‘MUSIC’ folder responds to ‘MUSIC’ button of remote controller and ‘MUSIC’ icon of main
menu. And, ‘PHOTO’ folder is also same.
- You may make any name of folders freely.
• Do not store too many files into one folder.
- It is recommended that you make several sub folders and store files divisionally.
- In case that you did HDD partition with FAT32, it is recommended that you do not store
over 3GB files into one folder.
• In case that file name(folder name) is too long or has so many specific characters,
blanks or period marks, the file(folder) may cause some problem.
- In this case, change or reduce file(folder) name.
• Moving picture file and subtitle file should be in same folder.
-
Moving picture file and subtitle file should be in same folder. And, both files name should
be same except for ‘extension name’.
Disconnecting NTD36HD from PC
after finishing file copy
After finishing file copy, make sure that you need to next page procedure for
disconnecting NTD36HD from PC. Otherwise, copied files may have some damage.
17
Disconnecting from PC
When try disconnecting USB cable between NTD36HD and PC,
Make sure to follow below procedure.
1. Do double-click the icon of “Safely
remove USB……”.
2. Click “Stop” button after selecting
“USB Mass Storage Device”..
3. When the message like picture is
shown, disconnect USB cable
between NTD36HD and PC.
18
Connecting to TV with Composite(AV) cable
After power off NTD36HD and TV, connect them like below procedure..
•
The Composite AV cable is needed to connect with normal TV or Video and is for connecting
Composite video signal and 2CH audio signal simultaneously.
•
Connect yellow cable to the Composite connector of NTD36HD and to the VIDEO connector of
TV set.
•
Connect red cable to the FRONT-R connector of NTD36HD and to the Sound Input(Right) of
TV or Audio system.
•
Connect white cable to the FRONT-L connector of NTD36HD and to the Sound Input(Left) of
TV or Audio system.
•
You may refer to cable colors and connector colors.
•
Please do not misunderstand Composite connectors and Component(Y, Pb, Pr) connector
which is located on the bottom line of NTD36HD rear side.
•
If you want to use digital audio output(Optical, Coaxial), you don’t need to connect with red
cable and white cable.
•
In case that your TV set has S-Video input connector, you may enjoy higher display quality by
connecting with S-Video cable.(note : As we do not supply S-Video cable, you need to
purchase it by yourself from shop)
•
For more information, refer to user’s manual supplied by TV maker
19
Connecting with Component cable
or DVI connector
When connecting HDTV or other high quality displaying devices,
connect like below picture..
Connecting with Component cable
Connecting with DVI cable
•
For safety, connect cables after power off NTD36HD, TV and audio system.
•
You have to purchase DVI cable and other genders by yourselves from shop
20
Connecting with 5.1CH audio system
If you want to connect analog 5.1Ch sound output to your speaker, please
connect audio cables like below picture.
•
You need to prepare below cables or gender by yourself as those are not supplied together
with NTD36HD. (audio cable for analog 5.1Ch, 3.5 pie gender cable, etc)
•
Connect with analog 5.1Ch cables like upper picture.
•
If the input connector of speaker or audio system is the stereo jack(3.5 pie) type, you need 3.5
pie gender cable. According to below picture, connect it to each speaker properly..
CENTER
REAR-R
(Rear-Right)
FRONT-R
(Front-Right)
REAR-L
(Rear-Left)
FRONT-R
(Front-Left)
WOOFER
21
Connecting with Optical, Coaxial connector
If you want to enjoy high quality digital audio, connect with Optical or Coaxial
connector.
•
As the audio output through Optical or Coaxial is digital signal, separate devices like
DTS Decoder(or Receiver) is needed additionally.
•
For safety, connect cables after power off NTD36HD and audio system.
•
You have to purchase Optical cable or Coaxial cable by yourselves from shop.
•
Make sure that Optical cable is not bent severely.
•
Do not see optical light which comes from Optical connector. It may have a bad effect
on your eyes.
22
Connecting to Network
To connect NTD36HD to a network, some equipment is required.
Ethernet Network using a direct connection to a PC(IP Address setup : 36 page)
Connect the NTD36HD to a PC with a crossed
cable.
◈ Equipment required.
•
A crossed cable.
•
A window PC with an Ethernet connection.
Ethernet Network using a router
Connect the NTD36HD and a PC to a router or
switch HUB with 2 straight cables.
◈ Equipment required.
•
2 straight cables.
•
A window PC with an Ethernet connection
•
A router or Switch HUB
Wireless connection using a wireless router
Connect the NTD36HD and a PC to a wireless
router with a straight cable for PC.
◈ Equipment required.
•
A straight cable for PC.
•
A window PC with an Ethernet connection
•
A wireless router
Wireless Range.
Radio signals may be reflected by some obstacles or be absorbed by
others depends on their construction.
Heavy or big media file like HD file or DVD file is not streamed properly with
wireless connection.
23
Remote Controller & SET-UP Menu
To introduce remote controller structure and set-up.
Structure of Remote Controller
POWER
AUDIO OUT SELECT
MOVIE FODER HOT KEY
TV OUT SELECT
JUKEBOX CREATOR
MUSIC FOLDER HOT KEY
GOTO
PHOTO FODER HOT KEY
CLEAR ALL(JUKEBOX)
BOOKMARK
DELETE FILE(JUKEBOX)
SLEEP TIMER
MUTE
RETURN / CANCEL
PLAY & PAUSE
SLOW FOWARDING
BGM ON/OFF
SETUP
STOP
INFO/CURRENT TIME
+15SEC FWD/UP ▲
OK/SELECT
REVERSE /LEFT ◀
FORWARD/RIGHT ▶
-15SEC REV/DOWN ▼
-32~+32X FWD/REV
VOLUME
REPEAT/SHUFFLE
PREV./NEXT FILE
(DVD CHAPTER)
POINT TO POINT
SYNC SUBTITLE
ODD EJECT
ZOOM / SCROLL
COLOR SETTING
DVD TITLE/MENU
DUBBING AUDIO
DVD ANGLE
SUBTITLE
24
Booting Message & Main Menu
If power on NTD36HD, it is booted up like below picture.
1. Booting Message
This picture is displayed during bootingup.
In case of no –display.
TV Out mode is originally set as PAL/Composite. If no-display on TV screen
after booting up, try changing TV Out mode by pressing TV OUT button of
remote controller or on the front side of NTD36HD set with 2~3seconds time
interval.
2. Screen of Main Menu
Main Menu screen is displayed like below picture after completing booting up.
Main Menu is composed of several icons such as MOVIE, MUSIC, PHOTO, USB HOST, Network
and JUKE BOX(BGM). For explanation of each icon, refer to next page.
25
Review of each icon on Main Menu
Main Menu has several icons like below. If you select each icon, you can see
files stored in corresponding folder or storage.
MOVIE icon
If selecting MOVIE icon, it shows all contents in MOVIE folder of the basic
HDD. It will be convenient for you to use or manage files if you make “MOVIE”
folder in the root directory of HDD in advance.
MUSIC icon
If selecting MUSIC icon, it shows all contents in MUSIC folder of the basic
HDD. It will be convenient for you to use or manage files if you make “MUSIC”
folder in the root directory of HDD in advance.
PHOTO icon
If selecting PHOTO icon, it shows all contents in PHOTO folder of the basic
HDD. It will be convenient for you to use or manage files if you make “PHOTO”
folder in the root directory of HDD in advance.
USB 1 or 2 icon
In case that some devices are connected to USB HOST ports, these USB Icons
are activated. Once activated, those icons can be selected. Otherwise, you can
not click or select it.
NETWORK icon
In case that NTD36HD is connected to network properly through Wired or
Wireless LAN, this icon is activated and can be selected. Otherwise, you can
not select it.
JUKE BOX icon
In case that you made PLAYLIST with “JUKEBOX CREATOR” function, you
can enjoy music at any time by pressing BGM button of remote controller. The
title of playing music is displayed in the box of JUKE BOX icon.
In case of no folder like MOVIE, MUSIC, PHOTO.
In case of no folder(‘MOVIE’, ‘MUSIC’, or ‘PHOTO’ ) in HDD, all files and all folders in
the root directory of HDD are shown.
26
SETUP Menu and How to set up
If needed to change setting values before using NTD36HD, you can open
SETUP Menu like below picture by pressing SETUP button of remote controller
or NTD36HD set.
• SETUP Menu is classified like VIDEO, AUDIO, ETC, NETWORK, WIRELESS, EXIT. You can
select each item with Left/Right (◀, ▶) button of remote controller or NTD36HD set.
• To change setting values, if selecting main item, sub items are listed up. You can select each
item with Up/Down(▼, ▲) button.
• After selecting sub item, press OK button. Then, changeable setting values are displayed.
• Once you select one of changeable setting values with Up/Down(▼, ▲) button, press OK
button. Then, the value is saved and applied.
• If you want to go out without changing setting values, press RETURN button before you press
OK button for confirming any selected value. Pressing RETURN button, it makes you go to
previous step.
• After completing new setting, you can go back to main menu by pressing RETURN button
several times, by pressing SETUP button or selecting EXIT icon.
27
VIDEO Setting Change
In SETUP Menu, if selecting VIDEO icon, sub items related to video are listed up
like picture.
• TV Standard
NTSC :Korea, North America
PAL : Europe and else
• TV Type
4:3 (for normal TV)
16:9(for Wide TV such as HDTV or
Plasma TV
• Display
Original(Letter Box) :
Select this option in case of playing a wide movie(16:9) with an ordinary
4:3 TV. There will be margins on the upper and lower sides of the
screen.
Pan & Scan :
Select this option if you want a wide movie(16:9) to be adjusted fully to the
screen of ordinary 4:3 TV. The left/right of the movie is cut, and the margin of
top/bottom is disappeared.
Full Screen : Select this option if you want to adjust a movie fully to the
screen of TV with no consideration of original ratio. In this case, according to
the ratio of original movie, displaying size is enlarged upward/downward or to
the left/right.
• Video Out
Composite/S-Video : In case of connecting with TV through Composite, S-Video or
Component 480i output connector.
Component(each Mode) : In case of connecting with TV through Component(Y, Pb, Pr)
output connector.
DVI (Auto or each Mode ) : In case of connecting with TV through DVI connector.
VGA (each Mode ) : In case of connecting with Monitor through DVI to RGB Gender
connector.
※ By pressing TV OUT button of remote controller(or NTD36HD unit) several times,
you can change TV standard and Video Out mode in order. Standard modes
28
changeable in order is seven(7) level.
AUDIO setting change
In SETUP Menu, if selecting AUDIO icon, sub items related to audio are displayed
like picture..
• SPDIF
Down mix : If selecting this option, all kind of
digital audio(PCM, MP3, AC3, DTS) are decoded
into analog signal. So, you can hear sound
without any separate DTS Decoder(or Receiver).
Pass through : If selecting this option, digital
signal is outputted directly without decoding
process. So, you need a separate Receiver or
Decoder to hear sound in case of using digital
audio connectors(Optical, Coaxial)
• Audio Channels
2 ch : If selecting this option, it outputs analog
audio signal with 2CH. If you use 2CH speaker,
please select this option.
5.1 ch :
If selecting this option, it outputs
analog audio signal with 5.1CH. Without any
separate Decoder or Receiver, you can connect
with 5.1CH speaker directly
• Sound Effects
On : When power off and on NTD36HD, sound
effect comes out.
Off : No sound effect in power on/off..
• Music Play Mode
Single Play : It plays only selected music file.
Folder : It plays all music files in same folder
Shuffle: It plays all music file randomly in same
folder.
29
ETC(Other) settings
In SETUP Menu, if selecting ETC icon, sub items are listed up like below picture.
• Slideshow Interval : To control time delay for displaying next picture file during
slideshow.
3sec, 5sec, 10sec ~ 60sec (total 9 levels)
• OSD Lang. : To change OSD languages.
• Sub. Color : To change subtitle color when playing back a moving picture.
total nine(9) kinds available.
• Sub. Size : To change size of subtitle when playing back a moving picture.
total two(2) kinds(Large/Small) available.
• User defined background : To change the background of main menu with other picture
file that you want.
You choose a picture file in the basic
HDD or in folder through network.
• Use default background : To use original background by canceling the user defined
background.
• Factory reset : To clear all values set by user and to initialize NTD36HD with values set
at factory.
• Firmware Update: To select firmware bin file and to update with new firmware.
30
NETWORK setting
The sub option related to network will be displayed by selection of NETWORK icon.
• Network Connection : Select either “Wired Net.” (for the Ethernet connection) or
“Wireless Net.” depending on the type of network connection
you want to set up.
• Connection Status : It shows current network connection status.
• Address Setup:
DHCP(Auto IP) : IP address will be assigned automatically with using a router.
Static IP : IP address should be assigned manually by user with Ethernet networking using a
direct connection to the computer. Input the IP address, Netmask and Default gateway.
• MAC (wired) : It shows MAC address of wired LAN.
31
WIRELESS(Auto setting)
This section shows how to make wireless network setup automatically to
communicate with devices under network environment. You don’t need to change
any setting value manually.
AP SEARCH
Click “AP SEARCH” to look for AP
available.
List of AP available
You can select the AP that you want
to use and press “OK” button.
In case that you set ESSID as ‘hidden’ or you set
‘Password’ for your AP.
In case that you set ESSID as ‘hidden’ or you set ‘password’ with your AP, you
need to enter ESSID name or Password by yourself. For entering ESSID name or
Password, NTD36HD will show you the specific window.
32
Check “ESSSID”
You can make sure whether the setting
value(ESSID, Channel, etc) is right or
not. The setting values should be match
with your wireless router(or AP) or PC.
Then, you may press “RETURN” button
to store this setting and exit.
Getting IP address
The NTD36HD will try to get new IP
address from your router. It takes about
30 ~ 60 seconds.
With Adhoc mode
If you are using Ad-hoc mode, you
have to enter IP address manually on
“NETWOKR” section.
Check NETWORK icon activation
NETWORK icon will be activated if the
network is connected successfully.
Network
icon
activation
According to network security setting,
network status, etc, sometimes it will
take 5 ~ 10 seconds for the network
icon to be activated. So, you need to
wait for some time until the network
icon is activated.
33
WIRELESS (Manual setting)
This section shows how to make wireless network setup manually to communicate
with devices under network environment.
Before setting this section, check that Connection should be set Wireless
net. on NETWORK section.
If you are running wireless network, all device on your network need to
share the same ESSID, CHANNEL, Wireless security and Encryption key in
order for them to communicate each other. If you do not know what method
of authentication is enabled in your wireless router/AP, please refer to its
manual on how to see or set it up.
ESSID
The ESSID of NTD36HD should be
exactly same as that of the wireless
router or the AP(access point) that
you use under network environment.
WORDING.
The “SSID” is also referred to as the
“ESSID” or “Extended Service Set ID”
CHANNEL
The 802.11g and b specifications
supports up to 14 overlapping
channels for radio communication.
You can select from AUTO to CH13.
The selected channel of NTD36HD
should be as that of the wireless
router or the AP(access point) that
you use under network environment.
34
Wireless Security
(Authentication Method)
You can set different authentication
methods which determine different
encryption schemes. There are 6
authentication methods(WEP Auto,
WEP SHARED, WEP OPEN,
WPAPSK, WPANONE, WPA2PSK).
Encryption algorithm
(WEP or WPA)
The encryption algorithm determines
the authentication method you
select.
Relation.
Authentication
Method
Encryption
Algorithm
WEP Auto
WEP SHARED
WEP OPEN
NONE
WEP
WPAPSK
TKIP
WPA NONE
WPA2PSK
AES
Encryption (WEP)
Encryption(WEP) option should be
applied in case that “WEP”
encryption algorithm is used.
The encryption setting of NTD36HD
should be exactly same as that of
the wireless router or the AP(access
point) you use under network
environment.
35
Encryption(WPA ,Pre-Shared Key)
Encryption(WPA) option should be
applied in case that “TKIP” or “AES”
encryption algorithm is used.
The encryption key of NTD36HD
should be exactly same as that of
the wireless router or AP(access
point) that you use under network
environment.
MAC (wireless)
It shows MAC address of wireless
LAN
Review of wording related to Wireless, Security.
Each manufacturer may use different wording when naming each function. Make
your reference for below wordings.
ESSID : referred to as SSID or Extended Service Set ID
ASCII when WEP key or WPA key input : referred to as Characters
HEX when WEP key or WPA key input : referred to as Hexadecimal
Wireless security : referred to as Authentication method or Type.
Encryption : referred to as Encryption Algorithm or Encryption Type
NONE : referred to as NULL
WPAPSK : referred to as WPA P-Key, WPA Pre-Shared Key or Network Key
Key : referred to as Key Value
36
WIRELESS (AD-HOC Setup)
There are several ways to set AD-HOC mode, but the following way is the easiest
way to set AD-HOC setup. Please see the following procedure.
NTD36HD NETWORK setting
Go to NETWORK in SETUP menu
and enter the following lists.
A
B
C
D
E
Wireless Net.
Static IP
200.200.0.2 (IP Address)
255.255.255.0(Subnet Mask)
200.200.0.1
NTD36HD WIRELESS setting
Go to WIRELESS in SETUP menu
and enter the following lists.
A
B
C
D
E
AD HOC.
Enter ESSID(ex. abc)
Select Channel (ex. Ch11)
Select “WEP AUTO”
Select “NONE"
Save setting and Return to main
To save setting and return to main,
press “SETUP” button on remote
controller.
37
Set IP and Subnet mask with a PC
On the PC, select Network
connection in the control panel.
Open Properties for the network
connection that is connected to the
NTD36HD. Select Properties for the
Internet protocol(TCP/IP). Select
“Use the following address”.
Enter the IP address below.
IP address : 200.200.0.1
Subnet mask : 255.255.255.0
Click “OK”
Zero Configuration utility-a
Open wireless zero configuration
utility and choose a wireless network
with same ESSID(ex.abc) that you
entered with NTD36HD.
Click “Connect”.
Zero Configuration utility-b
After connecting successfully, you
can browse shared folder with
NTD36HD.
Refresh
network list.
If you can not find the ESSID that you
entered with NTD36HD, please try to
click
“Refresh
network
list”
on
wireless Network Connection.
38
LAN Sharing setting(PC)
With shared folder, you can easily get multimedia file like movie, music and photo
as if these files are in HDD of NTD36HD. To use shared folder, you must proceed
the following steps.(based on window XP)
NOTE.
If firewalls are set in your PC, it may cause problem for NTD36HD to communicate
with your PC. So, you need to disable the firewall program in your PC.
1. Click right button of
mouse on the folder that you
want to share and select
“Sharing and Security...”.
2. Check on “
Share this
folder on the network”.
Fill in the box of “Share
name”. And then, click
“OK” and “Apply” button for
confirmation.
39
3. Then, each shared name will
be listed up on screen if
NTD36HD is connected.
Network configuration under window 2000
STEP 1
Click the right button on
“My Computer” icon and
choose “manage”
STEP 2
Go to “ Local Users and
Groups”
40
STEP 3
Click the “ Users” folder
STEP 4
Click the
right
button
on
“Guest” and click “Properties”
STEP 5
Release the check box on
“Account is disabled” and
Apply this setting
41
STEP 6
Check that “Guest” will be
activated.
STEP 7
Click right button of mouse on
the folder that you want to
share and select “Sharing…”
STEP 8
Click radio box on “ Shared
this folder” and click the
“Permissions”
42
STEP 9
Click the “Add…”
STEP 10
Click the “Add” after selecting
“Guest” and Click “OK”
STEP 11
Check the added “Guest” and
apply this setting.
43
STEP 12
Go to security tab and click the
“Add…”
STEP 13
Click the “Add” after selecting
“Guest” and Click “OK”
STEP 14
Check the added “Guest” and
apply this setting.
44
IP Address Setup :Ethernet Network
using a direct connection
Without a router or HUB, you can connect to a PC directly with crossed cable.
If your PC has only one LAN card and it is already occupied for internet connection,
you need one more LAN card for NTD36HD connection if you use both
simultaneously.
Please see the below guides step by step to set IP address.
1. Select Network Connection in
the Control Panel. Select the Local
Area Connection to be connected
with NTD36HD and click the right
button
of
mouse.
Select
Properties.
2. Select internet Protocol
(TCP/IP) and click Properties.
45
3. Select “Use the following IP
address”
Enter the IP address below.
IP address 192.168.0.1
Subnet mask 255.255.255.0
5. Then, start NTD36HD, press
“SETUP” button on your remote
controller and go to “NETWORK”
section. Select “Ethernet” on
“Network Connection” and “Static
IP” on “Address Setup” Then input
the following address.
IP Address 192.168.0.2
Netmask 255.255.255.0
Default gateway 192.168.0.1
Press “SETUP” on your remote to
exit this menu. Check that
NETWORK icon is highlighted on
main screen.
46
MULTIMEDIA FILE PLAYBACK
This section explains about basic operation for Multimedia
file playback.
How to use JUKE BOX CREATOR(BGM)
1. Go to JUKE BOX CREATOR
Click the “JUKEBOX” on screen or press
“JUKEBOX” button of remote controller. Then,
“JUKEBOX CREATOR” screen will be
displayed..
JUKEBOX
+
“OK”
2. Make ‘PLAYLIST’
Select music file and press “OK” button. Then,
each selected file will be stored into ‘PLAYLIST’.
Not selected music icon
Selected music icon
3. Playback files stored in ‘PLAYLIST’.
To play selected music files, select the “PLAY
▶” on screen and press “OK” button of remote
controller. And you may return to file browser
screen through “EXIT” on screen. JUKEBOX
on/off can be controlled by pressing “BGM ON”
button of remote controller. * Note : if you select
‘CLEAR’ on screen and press “OK” button, all
files in ‘PLAYLIST’ are deleted.
47
4. Reference
JUKEBOX function can be used when you
do other jobs like Photo Slideshow or Onscreen jobs.
Enjoying movie file
1. Loading Message
Press “PLAY ▶∥” or “OK” button to start movie
file. When loading a file, this message comes out.
Depends on supported file format and size,
loading time is different
2. Fast searching
In playing a movie file, you can search the
position that you want to see by pressing “REW,
FF” button. It supports up to 32X searching.
1 press:
2X
2 press:
4X
3 press:
8X
4 press: 16X
5 press: 32X
48
3. Previous/Next file Playback
Pressing “−PAGE+” button, previous or next
movie file will be played.
After pressing
“-PAGE+ “button,
Select YES or NO by
pressing
“◀”, “▶”button and
press “OK” button.
4. GOTO function
In playing DVD, if you pressing “GOTO” button,
you can go to the specific position that you want.
After pressing “GOTO”
button, input the time and
press “OK” button
XX : YY : ZZ
(H) : (M) : (S)
5. Control Volume level
In playing movie file, press “-VOLUME+” button.
49
6. MUTE
For sound off, press “MUTE” button. To clear this
function, press “MUTE” button once again.
7. Checking information of playing file
In playing movie file, press “INFO” button. The
playing file information will be shown..
“INFO”
1st press
8. Checking current playing time.
To check current playing time, press “INFO”
button two times. To clear this, press “INFO”
button once again.
“INFO”
2nd press
50
9. Controlling subtitle position and size
In playing movie file, you can control subtitle size
and position with S.TITLE button.
1st ~5th press
10. Multi Subtitle control
If the playing movie contains multi subtitle, you
can select a subtitle that you want to see by
pressing “S.TITLE” button. To select subtitle,
press “OK” button
2nd ~ 3rd press
11. Multi Audio control
If the movie file contains multi audio, you can
select an audio that you want by pressing
“AUDIO” button.
1st ~ 2nd press
51
12. Enlarging the screen
To enlarge screen size, press “ZOOM/SCROLL”
button and control the screen size by pressing
directional button(▲▼◀▶).
1st press
13. Scrolling the enlarged screen
To move enlarged screen, press “ZOOM/SCROLL”
button once again and move the enlarged screen
by pressing directional button(▲▼◀▶).
2nd press
14. Screen Color control
To adjust color setting, press “PICTURE”
Button and control Brightness, Saturation and
Contrast by pressing directional button(◀▶).
1st ~ 3rd press
52
15. Memorizing a specific position
In playing movie file, the current playing position
is saved by pressing “BOOKMARK” button.
16. BOOKMARK list
Pressing “BOOKMARK” button again, the latest
Bookmarked List is shown.(Max. 5 lists)
BOOKMARK
+
▲ or ▼
+
OK
17. Playback with slow speed
NTD36HD supports ‘slow playing back’ function
up to 1/32X.
1st press : 1/2X
2nd press : 1/4X
3rd press : 1/8X
4th press : 1/16X
5th press : 1/32X
53
18. Control subtitle sync
If a movie and a subtitle do not match, you can
control a subtitle showing time by pressing
“SYNC” button.
SYNC
+
◀ or ▶
1st press
19. Section Repeat – Set the beginning point
Press “A-B” button once to select the beginning
“A-“ point.
1st press
20. Section Repeat – Set the ending point
Press “A-B” button again to select the Ending
“-B” point. A-B section will be repeated. To clear
this setting, press “A-B” button once again.
2nd press
*note : This function is useful for language study or
enjoying sports moving picture.
54
Creating DVD Library and Enjoying it
You can create your own virtual DVD Library
by storing your private collection of DVDs
1. How to play.
As NTD36HD supports IFO and ISO file, you can
create your own DVD library by storing your
private collections of DVD into NTD36HD.
* IFO : Information file commonly found on
DVDs. Such
information..
files
contain
navigational
* ISO : One image file backup of the DVD title.
* FAT32 file system only supports up to 4GB.
* NTFS file system is unlimited.
2. DVD menu controlling
Using directional button, you can select DVD
menu from DVD menu screen.
3. Multi Subtitle Language Selection
In playing DVD, you can select a subtitle
language that you want by pressing “S.TITLE”
button.
55
4. Multi Dubbing Audio Selection
In playing DVD, you can select a dubbing audio
that you want by pressing “AUDIO” button.
5. Return to DVD menu Screen
In playing a DVD, you can go to DVD menu
screen by pressing “TITLE” button. When you
play DVD again after setting, it starts from
stopped position of DVD.
6. GOTO function
In playing a movie, you can go to the
specific
position that you want by pressing “GOTO”
button.
●
Volume control, color setting and media information are same as “Enjoying movie file”
functions.
●
To go next or previous chapter of DVD, use “-PAGE+” button.
56
Enjoying Music Library
NTD36HD supports mp3, WMA, OGG, M3U and PLS files.
1. How to play
Select a files in a folder that contains music
files and push “PLAY ▶∥” button .
2. How to change Music Play Mode
In playing a music file, you can change play
mode by pressing “REPEAT/SHUFFLE” button.
1st press : Single
2nd press : Folder
3rd press : Shuffle
3. M3U and PLS file support
NTD36HD supports M3U playlist and PLS playlist
by created WINAMP. To play these files, music
files linked with M3U and PLS should be in same
HDD partition.
57
Enjoying Photo Library
NTD36HD supports JPG, BMP and PNG files.
1. How to play.
Select a files in a folder that contains photo files
and push “PLAY ▶∥” button. Basically, all
photo files in same folder are played slideshow
with 10 seconds interval. You can change
slideshow time delay setting on “ETC” section of
SETUP Menu. If you want to see one photo file
only, please push “OK” button instead of “PLAY
▶∥”.
2. ZOOM / SCROLL of photo
You can enlarge the photo with direction keys of
remote controller after pushing “ZOOM/SCROLL”
button of remote controller one time.
Color setting function is same as “Enjoy Movie”.
58
External USB devices connection
Various external USB devices can be attached to USB HOST ports of NTD36HD
1. Connecting various external USB devices
With USB host function, NTD36HD supports
external USB devices like hard drives, memory sticks
and USB card readers up to two devices one time.
2. USB connection usage.
Once you have connected your device properly,
you can access the files in the USB device by
pressing the highlighted USB icon.
NOTE
NTD36HD supports mass storage
device in “read only” mode only.
3. ODD tray controlling
NTD36HD controls ODD tray on and off by pressing
“EJECT” button when ODD USD device is connected.
59
Firmware update
This section explains how to update firmware.
Getting the latest firmware to enjoy the added features and improved function.
1. Firstly, visit NTD36HD website(www.iamm.co.kr) or designated website(Please ask the shop
where you bought NTD36HD). You can download the newest firmware and save it on your PC.
2. Please extract the compressed firmware file and move or copy the file into NTD36HD through
USB cable. If NTD36HD is connected an internal network, installing the newest firmware via
internal network is also possible without copying the firmware file into a NTD36HD. In this
case, the firmware file should be stored in the shared folder of PC.
3. Connect the NTD36HD to a TV and power it on. Click the “SETUP” button on remote controller
and go to ETC setting section of SETUP.
4. Select “Firmware update” and search the
folder where the new firmware file is saved.
5. Select update file and push “OK” button on
remote controller.
6. Firmware update will start automatically
when you select “Yes” on confirmation
message box.
7. NTD36HD will power off in 10 sec
automatically
after
update
process
is
completed successfully.
8. Power on NTD36HD again, then go to “ETC” section of SETUP. Select “Factory Reset” and
press “OK” button for factory reset. And, power off NTD36HD again. After this, you can enjoy with
new firmware.
* Caution !!!
While updating, please make sure that NTD36HD is not powered off. If powered off
while updating, the NTD36HD has t be repaired from customer service center.
60
HDD Partition and Formatting
This section explains how to make partition and format the
HDD installed in NTD36HD.
Under Window 98SE/ME environment
Single partition is recommended.
Even if NTD36HD supports multi partitions, we recommend single
partition for your convenient using.
1. Open command prompt program(Start-
Program
2. Type “fdisk” and click enter.
Select “Y” to enable large disk support.
61
MS-DOS Prompt)
3. Click “5” to change current fixed disk
drive.
4. Select the last Disk number that you
want to initialize.
In case of more than 2 HDDs
In case that there are several hard disk drives in your PC, the disk
number may be changed. In this case, you can select the number
corresponding to each percent(“%”).
62
5. Select “1. Create DOS partition or
Logical DOS Drive .
6. Select “1. Create Primary DOS
Partition”.
7. Wait to be finished verifying drive
integrity until 100%.
63
8. Select “Y” and Enter to use the
maximum available size for a Primary
DOS Partition.
9. Wait to be finished verifying drive
integrity once again and click “ESC”
two times to finish MS-DOS prompt
program.
10. Reboot your PC.
11. After restart, the new hard disk drive
will be shown on My Computer. Click
the right button of your mouse and
select “Format” to be formatted.
64
Under Windows 2000/XP environment
1. Click the Start and go to
Control panel. Then, select
“Performance & Maintenance”
2. Select “Computer Management”
and go to “Disk Management”.
3. Click the next on “The initialize and
Covert Disk Wizard” window.
65
4. Select disk to initialize and click the
next.
5. Click the Finish on “ Completing the
initialized and convert Disk Wizard”
window.
6. Click the right button on your mouse
and select the “New Partition…”.
66
7. Click the next.
8. Select “Primary partition” and Click
the next.
Important
NTD36HD work properly with TV in
case of Primary partition type only.
9. Specify partition size and click the
next.(10GB = 10000 MB)
67
10. Click the next.
(Drive letter will be assigned
automatically)
11. Select file system and click the next.
(FAT32 can not be selected over 32GB
HDD).
Important
Do not check “Enable file and folder
compression.
12. Click the finish to close “The New
Partition Wizard”.
13. After setup the New Partition Wizard, the new HDD will be formatted automatically. Please
wait until 100% formatting is completed.
68
Troubleshooting
Before contacting Customer Service Center, please check
below points first.
Problems related to TV screen
1. In case of no-display on the TV screen.
Check if TV Out mode is set properly with your TV or Monitor. You may use TV
OUT button of remote controller(of NTD36HD unit). Press this button several times
with 2~3sec time interval.
Check whether you set your TV as Video input or Component input.
Check if A/V cable or Component cable is connected properly and firmly.
Check whether the file that you want play is supported by NTD36HD, or not
2. Much noise on TV screen.
Check whether video cable is connected properly and tightly.
Check if TV Out mode is matched with your TV, or not.
In case that you connect NTD36HD to TV indirectly through DVD player or VCR,
etc, there may some noise on TV screen. Please connect NTD36HD to TV directly.
In case there is some moisture inside of NTD36HD when you move it from cold
outside to warm inside, you need to wait for some time until NTD36HD is
conformed to inside temperature.
3. In case that the size of playing picture does not fit to TV screen.
As aspect ratio is fixed, please set it properly again in the SET-UP menu..
69
Problems related to Sound
1. In case of no-sound or much noise
Check whether stereo cable(A/V cable) is connected properly and tightly
between NTD36HD and TV set.
Check if [MUTE] button is pressed and volume level is set properly
Check whether digital audio cable is connected properly and tightly to the audio
input connectors of Home Theater System or Audio Amplifier
Try changing the value(Down mix or pass through) of Audio Out on SET-UP
menu
Try changing audio cable with new one.
Check the Audio channels(2channel or 5.1 channel) on SETUP MENU
2. In case of no-sound or bad sound quality when connected with digital audio
system
Check the Audio channels(2channel or 5.1 channel) on SETUP MENU
Set as ‘pass through’ on SETUP menu.
Check the status of connection and set up for digital audio system(Refer to the
manual of digital audio system)
Check whether optical cable or coaxial cable is connected properly and tightly
70
Problems related to HDD
or Remote Controller
1. In case that NTD36HD does not recognize HDD
Check whether the root folder or specific folder contains too many files. In
this case, make sub folders and move some files to the sub folders to
reduce files number in specific folder.
Check whether HDD is connected with NTD36HD properly(Check SATA
flat cable and power cable)
Check whether HDD is formatted properly( It should be based on ‘Primary
partition’ and you must not check ‘file and folder compression’ option in
formatting HDD)
Check HDD jumper setting(It must be set as ‘Single’ or ‘Master’)
Try changing with new HDD(There may be some problem in HDD itself
caused by impact or damage from outside.)
2. In case that PC does not recognize NTD36HD as external USB mass storage.
If PC is operated by Windows 98SE, you need to install the USB driver for
Windows98SE into your PC properly.
Check whether NTD36HD is powered ON.(It should be powered ON)
Try changing with new HDD(There may be some problem in HDD itself caused
by impact or damage from outside.)
3. In case that Remote Controller does not work properly.
Check if there is any obstacle between remote controller and IR Receiver of
NTD36HD
Check battery of remote controller.
Check whether the IR receiver is exposed to strong light such as direct sun
light.
71
Problem related to NETWORK
As the network is not set up correctly. Try setting up again according to
“Setting up NETWORK(Page 31)
Check cable connection status. Cables should be connected to each port
of the Router or switch HUB properly.
The NTD36HD and PC are not on the same NET MASK( Subnet)
Wrong IP address input, check the IP address and subnet mask
The NETWORK icon is activated, but can not read the Shared DATA. In
this case, check whether firewall is set in PC. If firewall is set, please
disable it for NTD36HD to communicate with PC.
Contact to below for Customer Service.
72
SPECIFICATION
High Definition Multimedia Player, NTD36HD
File Playback Format
Video
HD file format (tp,trp ts), Window Media 9, Window Media 9 HD
DivX3.11,DivX4, DivX5, DivX HD, Xvid, MPEG1, MPEG2(IFO,VOB,ISO)
Audio
MP3, Ogg Vorbis, WMA, AC3, DTS
Picture
JPEG, BMP, PNG
Subtitle
SMI, .SUB, .SRT
Output Connection
Video
Audio
USB Interface
DVI-D, Component Video (Y, Pb, Pr), S-Video, Composite Video,
Maximum Resolution:
Up to 1920 x 1080 Progressive Scan
Analog 2 Channel Stereo(AC3 & DTS down mixing)
Analog 5.1 Channel, Optical & Coaxial Digital Audio out
1 x USB 2.0 Target port, 2 x USB 2.0 Host port(Bus power Max 500mA)
1 x RJ45 LAN port (Ethernet 100BASE-TX/10BASE-T)
Networking
Optional 54Mbps Wireless LAN(IEEE 802.11b/g, 64/128bit WEB
security)
HDD Type to be Used
Size
3.5 inch type Hard Disk Drive
File Format Support
NTFS, FAT32
Compatible Operating System
OS
Windows 98SE, ME, 2000, XP or Higher
Physical Dimension & Weight
Dimension(mm)
Width(95mm) x Height(190mm) x Depth(145mm)
Weight(g)
730g (Excluding HDD),
Approx. 1,240g(Including HDD)
Power / Operating
Power Adapter
Operating
Input : AC 90V ~ 240V 50/60Hz 1.5A Output : DC 12V 3.5A
Temperature : 0 ~ 40 ˚C
Humidity : 10 ~ 70%
* note : specification may be changed without any notification
73

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement