ITB14/00855 Annex 1 to Section 3 (amended)

ITB14/00855 Annex 1 to Section 3 (amended)
Annex 1
Technical Specifications of required equipment for
Slobozia, Grigoriopol, Rybnitsa Maternity Unit and Pediatric
ICU Tiraspol
Item
ITEM 1. TABLE FOR WARMING AND NEWBORN
RESUSCITATION
1.1.
Standard requirements
1.2.
Basic Structure
1.3.
Accessories
Quantity
2
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Height adjustable table
Resuscitation Radiant Warmer consisting of:
Heat source
Bassinet and mattress
Mounting column with fixed height
System for resuscitation
Suction devices for cleaning of the neonatal airways
Storage compartments
Front drawers for storage
X-Ray tray
Rails for accessories
Patient skin probe
a) Heat source controller and functions:
Mean irradiance at mattress level: minimum 10 mW/cm2
The central Control panel will display all instructions in English or
Russian language
Control panel located centrally at eye level
Microprocessor controller with control modes:
− Manual mode in minimum 5-10 % increments from 0 to 100%
− Automatic (pre-warm) mode
− Servo (baby) mode
Servo control temperature range between approximate: 35 – 37 °C
Display temperature range between 30 and 42 °C
Examination lamp of minimum 50 W and minimum 1,000 Lux
Apgar timer integrated
Patient skin probe, reusable – 2 pieces
b) Bassinet and mattress:
Mattress area minimum: 3,000 cm2
Mechanical or Hydraulic tilt mechanism for the bassinet at least: +/10° minimum
Mattress thickness:
− minimum 2 cm
− Ray cassette tray to fit under mattress-1 piece
Four foldable bassinet walls
Ventilator tube supports
c) Mounting column:
Fixed height column on mobile castors
1
Item
ITEM 1. TABLE FOR WARMING AND NEWBORN
RESUSCITATION
Quantity
2
Built in rails for accessories – 2 pieces
d) Resuscitation module
Wall supply pressure 3 - 6 bar
Cylinder for oxygean and cylinder for compressed air pressure
2,900 psi max (19,994 kPa)
Adjustable positive end expiratory pressure
Pressure (PEEP) 0-25 cm H20
Gas bleed 0-15 L/min
Precision blender 21-100% O2 +/-3%
Mask for resuscitation size 0,1 and 2, two pics. for each size, Circuits
T-Pieces
1.3.
Accessories
1.4.
Warranty and Service
Conditions
1.5.
Incidental Services
e) Storage compartments:
Front storage drawers – 2 pieces
f) Alarms:
Audio alarms
Controller heating alarms
Check patient 15 minutes in Manual Mode
Baby temperature +/- 1° C from Set Point
High temperature Skin Temp. 39.0º C+/- 0.2° C
Probe Short or open circuit / No probe
System fail Indicates System Fail
Power fail AC Power Interruption
Alarm silence/reset intervals
Check patient Resets clock for 15 minutes manual mode
Baby temperature 10 minutes
High temperature 2 minutes
Procedural silence Presilences baby temp alarm for 5 minutes
Alerts
Manual mode System alerts every 30 seconds>10 minutes, for 15
minutes
Apgar timer Alerts at 1, 5 and 10 minutes
g) Physical properties:
Total height: maximum 200 cm.
Mattress height at approximate 100 cm.
Weight: maximum 100 Kg. (excluding accessories)
Power requirements: 220/240 V, 50-60 Hz
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
2
Item
Quantity
1
ITEM 2. PEDIATRIC/INFANT VENTILATOR
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
2.1.
Standard requirements equipment
ISO 9001 certified companies
This specification establishes the requirements for comprehensive
ventilators with the latest technology to ventilate neonates/infants
and pediatric patients in Pediatric Intensive Care Units.
Be able to ventilate patients with a weight range of approximate
550g to 50Kg in all the ventilation modes.
General requirements identify requested functions
Electro-pneumatically controlled
Built-in graphic display with backlight
Microprocessor controlled
Electronic blender built-in
Dual flow system for independent setting of in - and expiratory
flow
Proximal flow sensor, reusable, autoclavable
Inlet pressures from approximately 1.5 to 6 bar
Capable for transports with min. 60 minutes independent from
medical air hospital system
The ventilator shall provide the following ventilation modes, both
invasively and non-invasively for Infant and Pediatric ventilation:
− Assist /Control in Volume and Pressure mode;
− Time Cycled mode;
− Synchronized Intermittent Mandatory Ventilation - in
volume and pressure mode;
Continuous Positive Airway Pressure with Pressure supported
ventilation:
− Spontaneous;
− Manual Breath;
2.2.
General Characteristic
− Inspiration Hold;
− Expiration Hold;
− Back Up / Apnea Ventilation in all modes.
The ventilator shall provide the following breath types for Pediatric
and Infant modes:
− Pressure Limited Volume Control;
− Pressure Control with Volume target;
− Pressure Ventilation with alternating baselines (CPAP/PEEP);
− Timed Oxygenation (100%).
The offered unit shall have automatic switch over to a built in
battery unit with a capacity to ensure full functionality of the unit
for approximately 2 hours.
The offered unit shall have automatic switch over unit that will
switch between the piped air and oxygen supply should one of the
supplies fail.
The offered unit shall have a circuit compliance compensation
approximately 0.0 to 7.5 ml/cmH2O and must be automatically
measured.
3
Item
Quantity
1
ITEM 2. PEDIATRIC/INFANT VENTILATOR
Monitoring and displayed parameters. LCD or LED display
The central Control panel will display all instructions in English or
Russian language
Parameters
Approximate ranges are indicated, slight variations will be
accepted
− Respiratory rate per minute: Pediatric/Infant: 1 to 120 b/min.
− Inspiratory Flow: Pediatric/Infant: 0,4 to 100 L/min.
− Inspiratory Time: Pediatric/Infant: 0.1 to 3 seconds;.
− Time expiratory 0,2-20 s
− Pressure Support: Pediatric/Infant: 0 to 50 cmH2O
− Pressure Limit: Pediatric/Infant: 0 to 70 cmH2O
− PEEP/CPAP: Pediatric/Infant: 0 to 30 cmH2O
− I:E 1:4 to 4:1
− Flow Trigger: Pediatric/Infant: 0,1 to 20 L/min .
− Oxygen Concentration from 21% to 100%.
− Leak Compensation: Pediatric/Infant: Up to 8 L/min.
− Breathing: Selectable up to 1 to 150bpm.
Alarms
Both audible and visual alarms shall be available on the following
ventilator & patient parameters:
− Patient disconnect
− Oxygen concentration variation
− Over and under patient pressure
− Over and under patient volume
− High continues pressure
− Inverse I:E ratio
− Air/Oxygen % deviation;
− Low battery
2.2.
General Characteristic
− Power failure
− Air and Oxygen supply failure
− Air and Oxygen low pressure
Graphics Display
All parameters and functions of the offered unit shall be available
on a graphics screen.
Preferable 5 selectable waveforms shall be displayed at any time
on the graphic display screen.
The graphics display system shall have freeze capabilities.
The offered unit shall have the capabilities to display trending of at
least 24 hours on parameters of pressure-, flow- and tidal volumes.
The offered unit shall offer a graphical display unit that is able to
display the following parameters and measurements:
− Inspired tidal volume in ml;
− Inspired tidal volume in ml;
− Spontaneous tidal volume in ml;
4
Item
ITEM 2. PEDIATRIC/INFANT VENTILATOR
Quantity
1
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
2.3
2.4.
Accessories and
Consumables
Warranty and Service
Conditions
Total breath rate in bpm;
Spontaneous breath rate in bpm;
Minute volume in liters;
Spontaneous minute volume in liters;
Peak airway pressure in cmH2O;
Mean airways pressure in cmH2O;
I:E ratio;
Set I:E ratio;
Inspired time in seconds;
Static airways compliance in ml/cmH2O;
Dynamic airways compliance in ml/cmH2O;
Dynamic airways compliance per kg in ml/cmH2O;
Peak inspired flow rate in l/m;
Peak expired flow rate in l/m;
Inspired O2 in %;
Tube leak in %.
Humidifier
Microprocessor controlled
− Heater wire for in-and expiratory limb possibility
− Reusable and autoclavable humidification chamber
− Dual Servo controlled principle for temperature control
Miscellaneous
Operating Environment:
− Temperature approximately 10 – 400 C
− Humidity: approximately 10-90 % - non condensing
Connectors for medical gases:
− All connectors must compatible to EN ISO 7396, DIN 13260
–2
Trolley:
− minimum 4 wheels, 2 with brakes
− Bracket for humidifier
The following items must be included in the cost of the unit:
Durables
Reusable ventilator circuits pediatric, neonatal with heater wire
and water traps (in line) and nebulizer circuit -5 pcs
Reusable and autoclavable humidification chamber -5 pcs
Oxygen sensor 1 pcs/
Flow Sensor (reusable) 1 pcs.
Consumables
Single use circuits pediatric, neonatal with humidification chamber
included – 50 pieces
External oxygen & compressed air tubing
Test lung
Shelf – mount kit
Spare diaphragm for expiratory valve
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
5
Item
Quantity
1
ITEM 2. PEDIATRIC/INFANT VENTILATOR
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
2.5.
Incidental Services
location in Russian language
Installation
User manual in English or translated into Russian language
Item
ITEM 3. ANESTHESIA MACHINE
3.1.
Standard requirements
3.2.
Basic Structure
Quantity
1
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Equipment for mechanical ventilation and anesthesia for neonatal,
pediatric and adults
Compact mobile inhalation anesthesia machine with integrated
ventilator and monitoring for pressure, volume and oxygen;
System suitable for low flow and minimal flow anesthesia with rebreathing systems optimized for neonatal to adult patients’
Anesthetic ventilator capability to switch from spontaneous
breathing or manual to a mechanical one without the need of
reconnection.
General requirements identify requested functions
Basic unit including integrated gas supply consisting of central
supply connections for O 2 , Air and N 2 0 and integrated display of
central supply pressures
Integrated cabinet for covered and protected storage of reserve
minimum 5 liter gas cylinders for O 2 and N 2 0
Automatic switch-over to reserve gas cylinders in case of failure of
central gas supply
Compact breathing system integrated in basic unit
Vaporizing system for two vaporizers with interlock system
Monitoring and measurement of ventilation parameters and gas
parameters integrated in the basic unit
Unit for bronchus aspirator
Unit for monitoring vital parameters (heart rate, ECG, blood
pressure, saturation of oxygen and temperature)
Trolley with antistatic casters - two locking, drawers unit
Unit shall be equipped with all necessary accessories – min the
following: pressure reducers, connecting hoses, reusable
breathing hoses , vaporizer, sensors, filters, bronchus aspirator etc,
ready to work
Integrated anesthetic gas scavenging
Auto self check by start routine
Uninterruptible power supply 220VAC, 50Hz integrated in the basic
unit
Battery backup for min 30 minutes
Technical requirements for breathing system
Compact breathing system integrated in the basic unit with
6
Item
ITEM 3. ANESTHESIA MACHINE
3.2.
Basic Structure
Quantity
1
integrated infinitely adjustable positive pressure valve
Integrated quick vent valve for rapid manual pressure relief of
breathing system
Integrated pneumatic and electric interface for hoses and cables
connection of compact breathing system and basic unit as regards:
fresh gas supply, flow and pressure measurement; sample gas
return flow and possibility of gas scavenging
Possibility for connection for neonates, infant ,pediatric and adult
ventilation
Standby holder for breathing bag and Y – piece
Accessories needed for neonates, infant ,pediatric and adult
ventilation
Breathing system suitable for: spontaneous breathing
Manual ventilation
Volume controlled ventilation
Pressure controlled ventilation
Synchronized volume controlled ventilation
Pressure support of synchronized pressure and volume controlled
ventilation
Pressure support mode with apnea ventilation
Requirements for vaporizers connection
Connections for vaporizers integrated in the basic unit double plug
in system
Closes automatically when vaporizer is removed
Possibility to change between two volatile anesthetic agents
without being necessary to replace the vaporizer
Safety device interlock to ensure only one vaporizer operation
Basic unit equipped with isoflurane and sevoflurane vaporizers
Requirements for fresh gas delivery
Integrated in the basic unit with possibility for:
Delivery of fresh gas for gas mixtures of O 2 and N 2 O or O 2 and Air is
controlled
Fresh gas adjustments with mechanical-pneumatical or electronic
settings
Electronic carrier gas switch-over between air and N 2 O
Regulator to ensure an oxygen concentration in the nitrous oxideoxygen mix
Capability of delivery 21 vol % O 2 when using medical air as gas
carrier
Electronic regulator to ensure at least 25 vol % or 200 ml/min of
oxygen in the nitrous oxide – oxygen mix when delivery gas flow
below min 1 L/min
N 2 O is automatically cut in case of O 2 shortage
In case of O 2 shortage, switch over to 100% air is done
automatically at constant fresh gas flow - Optional
Capability of self resetting O 2 flush with a capacity of max 35L/min
for operation from central supply station with a nominal supply
pressure of max 5 bar
O 2 safety flow-adjustable min range 0 to 10 L/min running through
vaporizer
7
Item
ITEM 3. ANESTHESIA MACHINE
Quantity
1
The central Control panel will display all instructions in English or
Russian language
Basic settings of fresh gas quantity and composition can be
configured
Possibility for patient specific presetting of fresh gas quantity and
fresh gas composition in standby mode
Audible and visual alarms in case of air and N 2 O shortage
Audible alarms cannot be silenced in case of O 2 shortage
No possibility to increase pressure in vaporizer when O 2 flush is
activated
Requirements for the ventilator
No gas needed to drive the ventilator Ventilation electrically driven
Suitable for neonates to adults without changing any ventilator
parts
The system should preferably be able to measure volatile agent
and fresh gas consumption per case
Suitable for time cycled and volume controlled ventilation
Suitable for pressure controlled ventilation
Possibility of manual ventilation even if external and internal
power supply failure
Capability to check system compliance in standby after replacing
patient hoses
Possibility to configure all basic settings for anesthetic ventilation
for each specific ventilation mode
Possibility of patient specific pre settings for ventilation parameters
in standby mode and prior of changing ventilation mode
3.2.
Basic Structure
Adjustment ranges of ventilation parameters in volume mode;
approximate ranges slight variations will be accepted.
− Tidal volume: 20ml – 1500ml
− PEEP: 0 – 20 mmHg
− Inspiratory pause: 0 – 60 s
− Ventilation frequency: 5- 60 bpm
− I : E ratio 1:3 to 3:1
− T insp 0.5 – 6s
− Pressure limitation P max: 5 – 70 cmH2O
Preferably to have decelerating flow control
Adjustable flow trigger for synchronized volume and pressure
controlled ventilation
Flow trigger: min range 1,0 – 15 l/min
Ventilation parameters and alarm limits retained and presetting
determined on the basis of measured variables when switching
between ventilation modes
Presetting of ventilation parameters and alarm limits are weight
based
Requirements for ventilation and gas monitoring
Ventilation and gas monitoring integrated in anesthesia unit
Preferable operating concept screen based for all operational
functions
The central Control panel will display all instructions in English or
8
Item
ITEM 3. ANESTHESIA MACHINE
Quantity
1
Russian language
Capability of fully automatic compliance and leak test
Display of real time curves
Display of airway pressure
Display of volatile anesthetic agent concentration
Display of Inspiratory and expiratory flow
Display of minute volume
Capability to register and show on display or printed list, time and
event triggered list; please specify the available events triggered.
Measuring parameters of the ventilation and gas:
− Pressure measurement
− Tidal Volume
− Minute volume
− Measuring of gas concentrations
− O2 measurement
− CO 2 concentration
− Anesthetic gas measurement
− N 2 O measurement
− Measurement of volatile anesthetic agents
− Automatic recognition of volatile anesthetic agent and
mixtures of different volatile anesthetic agents
− Measurement (quantity) of two volatile anesthetic agents in
gas mixture
Alarms and limit values for ventilation parameters and gas
monitoring
Alphanumerical plaintext display of measuring parameters and set
alarm limit values
3.2.
Basic Structure
Audible and visual alarm priority within the alarm levels
List of all active alarms in order of priority
Configurable basic setting of alarm limits for each specific mode of
ventilation
Requirements for Bronchus aspirator
Bronchus aspirator with integrated ejector, bracket for secretion
jars can be removed from basic unit
Secretion jar package includes all necessary accessories
Integrated manometer for vacuum display
Requirements for monitoring the vital parameters
Device used for continuous monitoring of vital parameters for
neonates, infants , pediatric and adult patients. The device will
monitor heart rate, ECG with minimum 3 leads, saturation in
oxygen of hemoglobin, noninvasive blood pressure and
temperature. Possibility for visualizing the parameters on screen.
Alarms for each parameters mentioned above
Connectors for medical gases
All connectors must be type compatible to EN ISO 7396, DIN
13260 – 2
Requirements for uninterruptible power supply
9
Item
ITEM 3. ANESTHESIA MACHINE
3.3
Accessories and
Consumables
3.4.
Warranty and Service
Conditions
3.5.
Incidental Services
ITEM 4. COMPRESSOR FOR MEDICAL AIR
4.2.
Standard requirements
Characteristics
1
Integrated in the basic unit
Fully automatic switching to UPS in case of mains failure
Autonomy for approximately 60 min
Unit shall be equipped with all necessary accessories – min the
following: pressure reducers, connecting hoses, reusable
breathing hoses , vaporizer, sensors, filters, bronchus aspirator etc,
ready to work for
− 30 neonates
− 75 infant
− 400 children
− 100 children over 10 years
Will be specified all items included in offer
Device used for continuous monitoring of vital parameters for the
same number of patient neonates, infants, pediatric and adult
patients.
The device will monitor heart rate, ECG with minimum 3 leads,
saturation in oxygen of hemoglobin, noninvasive blood pressure
and temperature.
Reusable cables for ECG, SpO2, temperature probe ,cuff for NIB for
all size, disposable device for ECG,S pO2, temperature
Will be specified all items included in offer
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
4.1.
Quantity
Quantity
4
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Compatible with the resuscitation module from resuscitation table
ventilator and CPAP
Stand-alone medical air compressor .
Air Flow >40 L/min
Noise <60 dBA
adjustable pressure 2-4 bar
Snap fit with the resuscitation module from resuscitation table to
provide medical air
Air quality should comply with European Pharmacopoeia
compressed air purity class or ISO 8573
Replacement of internal filters should be performed without
removing the compressor
10
Item
ITEM 4. COMPRESSOR FOR MEDICAL AIR
4.3.
Warranty and Service
Conditions
4.4.
Incidental Services
ITEM 5. INTENSIVE CARE MONITOR
5.2.
Standard requirements
Characteristics
4
Provide at least 5 sets of air filters
Power Supply: 220 VAC, 50 Hz
24 months from the moment of installation
Maximum response time at beneficiary site: 48 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
5.1.
Quantity
Quantity
4
CE Mark
ISO 9001: 2000 certified companies
Color Screen – LCD or LED monitor
Minimum screen resolution: 800 x 600 pixels
Screen dimensions: Color screen with at least 300 mm diagonal
Speed of recording: 6.25, 12.5 or 25 mm/second
Visible in the same time on the screen:
− One lead ECG wave form and heart rate value, respiration
wave form and respiratory rate;
− Sp0 2 waveform and value;
− non-invasive blood pressure values (Systolic, diastolic and
mean) and temperature value
Central Control panel will display all instructions in English or
Russian language
Measures
− heart rate – beats per minute;
− respirations – breaths per minute
− SpO 2 – percent;
− blood pressure – mmHg;
− temperature - °C
Structure
Monitor
Battery
Patient cables in various lengths e.g. 3 & 8 foots or similar range
Cable for ECG + electrodes
Cable for blood pressure + cuffs
Cable for temperature + sensor
Cable for pulse-oximeter + sensors
Control buttons
On/off
Alarms – standard
Stand-by
Alarms
System failure
11
Item
ITEM 5. INTENSIVE CARE MONITOR
5.2.
Characteristics
Quantity
4
Battery low
Apnea
Bradycardia
Tachycardia
Low respiratory rate
High respiratory rate
Saturation low
Saturation high
Blood pressure low (systolic, diastolic, mean)
Blood pressure high (systolic, diastolic, mean)
Temperature low
Temperature high
All alarms mentioned above are adjustable by the clinician at the
bedside
All alarms are audio and visual alarms
The alarm tones can be regulated (high to low tonality to alarm off
at least)
Heart rate and EGK
One derivation visible all the time on the screen
There could be two channels visible optional
Limits: low limit at least 20 beats per minute, high limit at least 300
beats per minute
Derivations: I, II, III, aVL, aVR, aVF. Optional: V1, V2, V3, V4, V5, V6
Possibility to adjust the amplitude of the signal
Possibility to choose the lead to be displayed
Cable with 3 wires: I, II, III, aVL, aVR, aVF
Optional Cable with 10 wires: I, II, III, aVL, aVR, aVF. Optional: V1, V2,
V3, V4, V5, V6
Respiratory rate
Limits: low limit at least 0 breaths per minute, high limit at least 150
breaths per minute
Oxygen saturation of hemoglobin
O 2 saturation low limit at least 30%, high limit at least 100 %
Pulse rate: low limit at least 30 bpm (beats per minute) to high limit
at least 250 bpm
Adjustable averaging time
Signal quality meter on screen
Blood pressure
Oscilometry measurement
Measures and displays systolic and diastolic blood pressures
Automatically adjustable intervals of approximately 1 min – 8hours
Discriminates between pressure signals and patient movement
Display current and previous pressure values (systolic, diastolic)
Automatically zeroes prior to each reading
Blood pressure cable and cuffs for all age (mentioned above)
Temperature
Measurement: low limit at least 28°C, high limit at least 42°C
Cable for temperature monitoring to be connected with probe and
temperature probe or probe incorporated in the cable assembly
Mandatory rectal and skin probe
12
Item
ITEM 5. INTENSIVE CARE MONITOR
Quantity
4
Other condition
Power requirements: 220 VAC, 50 Hz
Autonomy with battery at least 2 hours
Automatically display of battery status fuel gage while operating
on battery power
Automatic internal recharge when the monitor is plugged into an
AC power supply
Low battery audio and visual alarm
Capable of recording all numeric and waveform information
displayed on the screen for min 24 hours
5.3.
Accessories
5.4.
Warranty and Service
Conditions
5.5.
Incidental Services
Extra battery – 1 piece
ECG cables with 3 leads – 2 pieces
Cuff set reusable, all dimensions newborn/pediatric and adult–
1set
SpO 2 (multisensor) sensor pediatric/adult with cable with
approximately 5 foots – 2 pcs
SpO 2 sensor newborn with cable with approximately 8 foots
(consumables for 500 tests)
ECG electrodes newborn/infant – 200 pcs
ECG electrodes/pediatric/ adult – 500 pcs
Blood pressure cable 3 ft – 2 pcs
Temperature cable 3ft – 2 pcs
Temperature probe covers – 500 pcs
Blood pressure cuffs Sizes: 1,2, 3, 4, 5 - 6 pcs each
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation and commissioning
User manual in English or translated into Russian language
Item
ITEM 6. PORTABLE PULSE OXYMETER
6.1.
Standard requirements
6.2.
Basic Structure
6.3.
Technical
Characteristics
Quantity
6
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Monitor for SpO2 and pulse rate
Portable pulse-oxymeter
Universal connection for sensors
a) Monitor:
Removable handheld display for SpO2 and pulse rate ensures
continuous monitoring
Oximetry technology clinically proven to work under motion and
poor perfusion conditions
13
Item
ITEM 6. PORTABLE PULSE OXYMETER
6.4.
Accessories and
Consumables
6.5.
Warranty and Service
Conditions
6.6.
Incidental Services
7.1.
Standard requirements
6
Patients perfusion level display
Sensor signal quality indicator to ensure best sensor position
placement
Full patient alarms including high and low saturation and pulse
rate
Downloadable min.24 hour memory at 2 seconds resolution with
the ability to review trend data on screen
Fast time to initial reading after sensor placement
Probe off detection system to alert user of probe displacement
High sensitivity mode for improved performance on poorly
perfused patients
LCD waveform display
User selectable averaging time
SpO2 range: 30 ÷100%
Pulse rate: approximately 0 ÷250 bpm
Perfusion (optional): 0.02% ÷ 10%
Saturation accuracy in motion for infant: ± 3 digits
8 hour battery life for the portable display
Configurable display, including big numbers option
On screen alarm values
Alimentation with power cord for 220 V
b) Sensors:
Sensors with recessed photo detector to reduce ambient light and
electromagnetic interference
Extended adhesive sensor life by use of rejuvenatable adhesive
Low weight adhesive sensors
Single patient use with proven clinical lifetime of minimum 8 days
Adhesive sensors manufactured from durable, moisture resistant
material
Interconnection cable 1 pcs
1 SpO2 sensor reusable for adults (finger)
1 SpO2 sensor reusable for children
100 single patient use SpO2 sensors for neonates
30 single patient use SpO2 sensors for neonates lower than 2 Kg
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation and commissioning
User manual in English or translated into Russian language
Item
ITEM 7. SUCTION UNIT
Quantity
Quantity
11
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
14
Item
ITEM 7. SUCTION UNIT
7.2.
Basic Structure
7.3.
Accessories and
consumables
7.4.
Warranty and Service
Conditions
7.5.
Incidental Services
11
Portable suction unit
Suitable for adults and neonates use
Vacuum range: between around -20 and -300 mmHg, adjustable
from a button
Vacuum indicator
Fast aspiration: at around 10-30 lpm flow
Sealed water resistant unit
Automatic float shut-off to prevent overflow into the unit
Preferable Integrate bacterial filter
Control panel tilted for easy viewing of the controls
Main body made of durable and resistant material
LED indication for bad battery
Indication for battery charge status
Remote internal AC charger for battery
Charging circuit capable of running on low battery
Power supply: 220VAC, 50Hz
Rechargeable battery:
Battery: rechargeable
Long operating time at full vacuum (uninterrupted min 40-60 min)
Low charge time: max 6-8 hours
Reusable collecting container: min 1000 ml. 1 pcs
Bacterial filter – preferable reusable. Please specify type of filter.
(For single use filters provide 50 pcs)
2 auto-clavable silicon suction tubes
Period: 24 months from the moment of installation of the
equipment
Battery warranty : at least 6 months
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation and commissioning
User manual in English or translated into Russian language
Item
ITEM 8. BASIC INCUBATOR
8.1.
Standard requirements
8.2.
Basic Structure
Quantity
Quantity
3
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Incubator hood
Temperature controller
Standard humidity module
Mobile stand
a) Incubator hood and mattress:
Double wall and other parts of incubator easily removable for
15
Item
ITEM 8. BASIC INCUBATOR
8.3.
Characteristics
8.3.
Characteristics
Quantity
3
cleaning
At least two opposite doors for quick access
Small range temperature drop with door down
Front door access
One iris port on each lateral side, two irises on front and back or
doors for access
Hood can be raised separately from front door
Mattress with minimum surface of 2,000 cm2
Tilting of the mattress
Tubing access – minimum 4
b) Temperature controller:
Microprocessor controlled
Automatic test on start-up
Heat up time to 39°C to be 30 minute or less
Removable control unit for easy service
Air flow pattern directed from front to rear of incubator across
entire width
Centralized display for patient, air temperatures control with
alarms
display for function settings, parameters and trending, easy to
operate and clean
Accurate air temperature control using two air probes
Air temperature range between: 20 and 39°C
Baby temperature control using reusable skin probe
Baby skin temperature range between: 35 and 37°C
Keypad lock function for protection
Override function at air temperature over 38°C
c) Standard humidity module:
Internal reservoir included
Front mounted for easy accessibility
All humidifier parts can be completely removed for filling and
cleaning
Humidity range up to 0-80% RH
d) Mobile stand:
Stand on four anti-static wheels, from which two locking
Height variable 90-110cm or more
Two front drawers
e) Alarms:
audio alarms
Baby set temperature: + / - 1 ° C
High/Low air temperature: +3 / -1 ° C or better
Baby skin temperature probe fail
Air temperature probe fail
Power fail
Air flow fail
System fail
f) Accessories included:
Front drawers – 2 pieces
Mattress – 1piece
16
Item
ITEM 8. BASIC INCUBATOR
8.4.
Accessories
8.5.
Warranty and Service
Conditions
8.6.
Incidental Services
ITEM 9. SYRINGE INFUSION PUMP
Standard requirements
9.2.
Basic Structure
9.3.
Technical
Characteristics
3
Rails for accessories – 2 pieces
Patient skin probe reusable –2 pcs
g) Physical properties:.
Interior Noise level <60dB
Interior Aer flow <35m/s
Power requirements: 220/240 V, 50-60 Hz
Ambient operating temperature: minimum 20- 30° C
Ambient humidity: 0 – 90 %RH
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation and commissioning
User manual in English or translated into Russian language
Item
9.1.
Quantity
Quantity
11
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Equipment for iv administration of drugs at controlled quantity and time
Syringe type infusion pump for constant drug administration
Flow rate: min range 0.1 ml – 999 ml/h (max 0.1 ml increments)
Possibility of changing the flow rate whilst infusing
Syringe loading sensor. The equipment will include KVO function
High accuracy over the entire delivery range min +/-5%
Accept all standard type syringe from 50/60 ml, 30/35 or 20 ml,10
ml or 5ml
Set-up fast and simple
Bolus mode programmable
Antibolus system
Warns of pressure variation when there is a risk of occlusion or a
possible leak in the infusion line
Occlusion in preselected mode: min. three pre-selectable pressure
alarm limits (occlusion)
Infusion continuity protection
Automatic internal battery operation during patient transfer AC
power failure
Infusion data memorization (flow rate, bolus rate, volume, volume
limit, KVO rate)
Event logging
Electronic pressure management
Fixing accessory for IV pole
Infusion alarm:
Pre-alarm end of infusion
17
Item
ITEM 9. SYRINGE INFUSION PUMP
9.4.
Consumables
9.5.
Warranty and Service
Conditions
9.6.
Incidental Services
ITEM 10. PHOTOTHERAPY LAMP
Standard requirements
10.2.
Basic Structure
10.3.
Technical
Characteristics
11
Pre-alarm volume limit
Occlusion alarm
Alarm for the end of infusion
Alarm for volume limit
Technical alarms:
Disengaged driving mechanism alarm
Low battery pre-alarm
Discharged battery alarm
Battery capacity display
Unconfirmed programming
Main malfunction alarms
Syringe position control
Syringe barrel clasp check
Plunger head detection
Occlusion pressure
Locking syringe
Fixing accessory
Power 220 V AC / 50 Hz
Battery life: min 3h/charge
200 connectors from the syringe to the patient for each syringe
infusion pump
200 syringe 20 ml for each syringe infusion pump
200 syringe 50 ml for each syringe infusion pump
24 months from the moment of installation
Maximum response time at beneficiary site: 48 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Equipment assembly and installation on site
User manual in English or translated into Russian language
Item
10.1.
Quantity
Quantity
3
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Phototherapy Unit
Mobile Stand
a) Phototherapy Unit:
Light characteristics:
LED lamp technology
The possibility of adjusting the angle
Irradiance >20 µM/cm2
Bulbs / tubes / lamp characteristics:
Estimated life time >30000 h
Specify the field size [cm] -Diameter
18
Item
ITEM 10. PHOTOTHERAPY LAMP
10.4.
10.5.
10.6.
Consumables
Warranty and Service
Conditions
Incidental Services
ITEM 11. LARINGOSCOPE
Standard requirements
11.2.
Technical
Characteristics
11.3.
Warranty and Service
Conditions
11.4.
Incidental Services
3
Low energy consumption
Fault protection (specify)
Maintenance free operation
Easy light source replacement
Eye protection 3 pics.
b) Mobile Stand:
− height adjustable between: minimum 45 -150 cm.
− on 3-4 castors with locks
lamp 1 set
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
11.1.
Quantity
Quantity
4
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Fiber optic laryngoscope:
Laryngoscope handle
Rechargeable battery
Knurled finish for sure grip
Blade with fiber optic for cool light
Halogen or xenon light for true tissue color
Long lasting illumination
Removable fiber optic light pipe for instant replacement
Fiber optic resistant about 1000 cycles of sterilizations
Blades:
McIntosh type, size 0, 1, 2, 3,4 - 2 pcs.
Miller type, size 00,0 1, 2, 3 – 2 pcs.
One piece stainless steel
Charger for battery: 220VAC, 50 Hz
Period: 24 months from the moment of installation of the
equipment
Maximum response time : 48 hours
Training for at least 2 medical and technical personnel on site at
beneficiary location in Russian language
Installation
User manual in English or translated into Russian language
19
Item
ITEM 12. RESUSCITATION BALOON
12.1
Standard requirements
12.2.
Technical
Characteristics
12.3.
Accessories
12.4.
Warranty and Service
Conditions
12.5.
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
ITEM 13. OXYGEN HOOD
Standard requirements
13.2.
Basic Structure
13.3.
Technical
5
CE Mark
ISO 9001: 2000 certified companies
Silicone resuscitation balloons for providing fast, simple, and
effective ventilation to non-breathing patients, self-inflating bags
in three sizes: adult / pediatric /pre term
Adult model - over 25 kg.
Pediatric model - 2.5 - 25 kg.
Preterm model - under 2.5 kg.
Adult bag with a minimum of 2 different size masks, patient valve
and supplementary oxygen admission system with reservoir and
valve
Pediatric bag with a minimum of 3 different size masks, patient
pop-off valve and supplementary oxygen admission system with
reservoir and valve
Preterm bag with a minimum of 2 different size masks, patient
pop-off valve and supplementary oxygen admission system with
reservoir and valve
Standard connections between the different components
Pop-off pressure release valve
Valve system respond to the rescuer and the patient
Possibilities to adapt to a pressure manometer
Audible overpressure alert
Extension tube for patient connection
Operating temperature range: min. -10°C to 50°C
Storage temperature range: min. -40°C to +60°C
Pediatric/ Neonatal mask 3 different size – 2 pcs. of each size
Pre term mask 2 different size -2 pcs of each size
Adult mask 2 different size – 2 pcs
24 months from the moment of installation
Maximum response time at beneficiary site: 48 hours
Incidental Services
13.1.
Quantity
Quantity
6
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Transparent oxygen hood for neonates with head / waist aperture
2(two)sliding doors
Silicone flap in the head / waist aperture
Suitable for neonates and infants
20
Item
ITEM 13. OXYGEN HOOD
Characteristics
13.4.
Warranty and Service
Conditions
13.5.
Incidental Services
ITEM 14. FETAL HEART DETECTOR
14.2.
14.3.
6
Fits into all incubators and open care beds / tables
Allows consistent and even oxygen flow to the baby
Manufactured from food-grade polycarbonate
Easy access on each side for I.V. lines, oxygen analyzers or ECG
wires
Big clear sliding doors
Raked head aperture
Soft material in the aperture for maintaining oxygen and humidity
Interior gas deflection system for preventing baby’s cooling
Possibility to measure the interior temperature
Period: 24 months from the moment of installation of the
equipment
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
14.1.
Quantity
Quantity
4
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
Standard requirements equipment
ISO 9001 certified companies
Compact, lightweight and portable device complete with carrying
case, rechargeable batteries, gel and optional head-set if any
Specify measurement method
Characteristics
Audible and visible heart beat indication
Fetal Heart rate calculation and display
FHR range 0 - 210 bpm
Large Display
Weight <700 g
Indicate displayed parameters
Speaker yes/no
Power Requirements: VAC 220, 50Hz / Plug Type F
CONTROLS:
Technical Requirements ON/OFF
Volume
Audio mute
Calibration
Easy to clean
Waterproof / fluid resistant
Battery operation
Rechargeable standard batteries
21
Item
ITEM 14. FETAL HEART DETECTOR
14.4.
Warranty and Service
Conditions
14.5.
Incidental Services
ITEM 15 CARDIOTOCOGRAPH
Standard requirements
15.2.
Characteristics
15.3.
Accessories
4
With integrated battery charger or ext. charging station
Consumables if any covering 1200 patients
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
15.1.
Quantity
Quantity
3
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Standard requirements
Fetal monitor for prenatal, labor and delivery monitoring
LCD or LED display
Built-in thermal recorder and printer
Dual Ultrasound Twins available for reliable non-stress testing and
routine labor monitoring
Color display and keyboard or similar for entry of patient name and
ID with numerical presentation of FHR and UA
Tachycardia and bradycardia alarm management
Adjustable alarms
Water-proof ultrasonic transducers
Backup memory
Fetal Heart Rate Monitoring
Ultrasonic measurement for fetal hear rate (FHR) with pulse
Doppler technology
Audible alarm and visual messages based on physiological alarms
Transmitter frequency minimum 1 MHz
Maximum constant intensity: < 15mW/cm2
Heart rate fetal counting range between approximately 60-200
BPM
Automatic detection of fetal movement
Uterine Activity
Uterine activity (UA) measurement with toco-transducer
Measurement range between: 0-100 relative units
Manual or auto zero adjust
FHR transducers- 2 pieces, with connection devices
TOCO transducer- 1 piece, with connection devices
Fetal monitor paper- minimum 6,000 sheets
Table top or roll stand support for monitor and transducers- 1
piece
22
Item
ITEM 15 CARDIOTOCOGRAPH
15.4.
Warranty and Service
Conditions
15.5.
Incidental Services
ITEM 16. DELIVERY TABLE
16.2.
Standard requirements
Technical
Characteristics
16.3
Warranty and Service
Conditions
16.4.
Incidental Services
3
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
16.1.
Quantity
Quantity
4
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Non-electric delivery bed to accommodate pregnant women in
various comfortable positions during labour and birth giving, and
for resting after the delivery in maternities of the first health care
level.
Robust, mobile delivery bed on castors with breaks
Easy adjustable sections (with handle)- ≥ 3 sections
Height adjustable (with handle)- 55-90 cm
Trendlenburg and reverse Trendelenburg position easy adjustable
with handle
Shoulder and head rest
Supplementary table completely recessable underneath the main
bed
Surface covered with soft material washable, resistant to chemicals
Standard side rails to fix accessories
Detachable, adjustable (height and width) leg support
Detachable, adjustable (height and width) knee crutches with
pads, cover and strap
Drain pan to collect physiologic and irrigating fluids
Waste receptable with drainage hose
Weight user ≥180kg.
Auxiliary side-arm board with pad, swiveling
Auxiliary height adjustable infusion pole
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
23
Item
ITEM 17. MOBILE EXAMINATION LIGHT
17.1.
Standard requirements
17.2.
Technical
Characteristics
17.3
17.4
17.5.
Accessories
Warranty and Service
Conditions
Incidental Services
ITEM 18. INSTRUMENTS TABLE
Standard requirements
18.2.
Technical
Characteristics
18.3.
Warranty and Service
Conditions
18.4.
Incidental Services
6
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Optical lighting system reflector for optimum illumination of the
operation light field, cool, white light, free from deep shadows.
Adjustable height and articulated arm.
LED lamp technology
Light-field size >120mm
Low power consumption: max 150VA
On-off switch
Lamp life: min. 20000 hours. Please specify
Light characteristics: Lux: approx. 15,000 at 1m,Color temperature:
approx. 4,300°K
Mobile stand with 5 castors at least 2 with breaks
Lamp must be water proof and fluid resistance for cleaning
purposes.
Spare lamp – 1 pcs (if applicable)
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
18.1.
Quantity
Quantity
8
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Stainless steel instrument table with shelf and four castors
Rubber coated swivel castors, at least two lockable
Top and shelf strong enough to place heavy materials
Dimensions approximately:
-Width 120cm
-Height 90cm
-Depth 60cm
-Distance between shelves 50cm
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
24
Item
ITEM 18. INSTRUMENTS TABLE
Quantity
8
User manual in English or translated into Russian language
Item
ITEM 19. NEONATAL MATTRESS HEATER
19.1.
Standard requirements
19.2.
Technical
Characteristics
19.3.
Warranty and Service
Conditions
19.4.
Incidental Services
Quantity
4
CE Mark
ISO 9001: 2000 certified companies
Equipment used for compensation of heat losses in neonates
Complete unit, microprocessor controlled functions for
temperature, set values, etc.
Temperature setting range
Main mode from
35,0 to 37,0
Additional mode from
37,1 to 39,0
Accuracy of temperature control ± 1,0
Maximum deviation of mattress surface temperature after
switching to maximum temperature mode ± 1,0
Switch off temperature of the heater when there is inadmissible
overheating of the mattress surface,
Heating time, not more than 20 min
Alarms
Alarm signaling OVERHEATING
Main mode at temperature within, ºC
38,0±0,4
Additional mode at temperature within, ºC 40,0±0,4
Other malfunctions are indicated by alarms
Mattress
Overall dimensions of the mattress, mm, not more than
− Height 20
− Width 600
− Length 750
Mattress cover antimicrobial, fire retardant, fluid-proof.
Control unit
Display with LED
Built in handle
ON/OFF
Display the temperature
Alarm ON/OFF
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
25
Item
ITEM 20. BRONHOSCOP
20.1.
Standard requirements
20.2.
Characteristics
20.3.
Accessories
Consumables
Quantity
1
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Medical device – diagnosis of lung and airways and remove foreign
bodies in the airway
Pediatric rigid bronchoscope for pediatric cases consisting of:
Rubber telescope guide for telescopes
Telescope: angle of view: 0⁰, diameter: between 2,7 - 2,9 mm
Telescope: angle of view: 0⁰, diameter: between 2,8 – 3 mm
Bronchoscope tubes and foreign body alligator extraction
forceps
Bronchoscope tubes for neonates and foreign body alligator
extraction forceps suitable for the bronchoscope:
− Size: between 3,3 – 4,3 mm
− Length: between 180 - 200 mm
Bronchoscope tubes for infants and foreign body alligator
extraction forceps suitable for the bronchoscope:
− Size: between 4,2 – 5,1 mm
− Length: between 250 - 265 mm
Bronchoscope tubes for small children and foreign body alligator
extraction forceps suitable for the bronchoscope:
− Size: between 4,9 – 5,5 mm
− Length: between 290 - 310 mm
Bronchoscope tubes for children under 10 years and foreign body
alligator extraction forceps suitable for the bronchoscope:
− Size: between 5,9 – 6,9 mm
− Length: between 290 - 310 mm
Bronchoscope tubes for children over 10 years and foreign body
alligator extraction forceps suitable for the bronchoscope:
− Size: between 7 – 7,9 mm
− Length: between 390 - 405 mm
− Light deflector for the described tubes
Suction pump
Instrument guide for suction catheter
Rigid suction tubes of approximate 35 cm length and 3mm
diameter with rubber tip, straight and curved.
Adaptor for respirator
Sealing plug for respiration catheter
Adaptor
with sliding glass window plug, sealing cap, notched lens and
keyhole opening, moveable
Cold light fountain
lamp lifetime: min. 500 h; Please specify
Fiber-optic light cable, length between 290 – 300 cm, between
diameter 3,4 – 3,6 mm
Forceps, pointed, serrated, for coins and flat foreign bodies,
double-action jaws, sheath diameter, compatible with
bronchoscope 1 pcs.
26
Item
Quantity
ITEM 20. BRONHOSCOP
20.4.
Warranty and Service
Conditions
20.5
Incidental Services
1
Forceps, for peanuts and soft foreign bodies, double-action jaws,
sheath diameter compatible with bronchoscope 1 pcs.
Bacterial filter 4 pcs.
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation and commissioning
User manual in English or translated into Russian language
Item
Quantity
ITEM 21. ECG
21.1.
Standard requirements
21.2.
Technical
Characteristics
1
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Equipment for recording heart electrical activity
12 channel ECG with 12 leads
Minimum 6 Number of traces to be displayed simultaneously
Preferable touch scree. LCD or LED
Resolution at least 640/480 pixels
Possibility of introducing for each patient the following data: name,
date of birth, date of recording, weight, age, diagnosis and
comments
12 leads ECG: limb derivations: I, II, III, aVL, aVF, aVR; precordial
derivations: V1, V2, V3, V4, V5, V6
Manual selection for any 12-lead.
Graphic LCD viewing area for life 3-channel display with patient
information.
Indicator for faulty leads.
Digital filters for all possible interferences. Please specify which
types of filters.
Calibration 1mV test.
Sensitivity and Frequency response test.
Working frequency 0.67-150 Hz
Band Filters: muscle, low frequency, high frequency, 50 Hz
Sensitivity adjustment - 5, 10 and 20 mm/mV.
Gain adjustment - x ½, x 1 and x 2.
Full screen preview to determine quality of ECG.
ECG interpretation with interpretation statements.
Low battery check and alarm.
Optional: indication of bradycardia and tachycardia.
Printer
Printing speed 25 mm/s or 50 mm/s.
Recording paper - thermal - A4 size.
27
Item
ITEM 21. ECG
21.3.
Accessories and
Consumables
21.4.
Warranty and Service
Conditions
21.5.
Incidental Services
1
Printout of patient ECG with patient information
Storing at least 100 records (at least 10 seconds long strips)
Defibrillation protection
Pacemaker detection
Built in accumulator. At least 2 hours autonomy
The accumulator is re-charging automatically
Thermal paper rolls ( or other system) – 20 pcs
Thermal paper rolls ( or other system) – 20 pcs
ECG cables and electrode reusable for adults and disposable for
150 patients (infant and small children)
24 months from the moment of installation
Maximum response time at beneficiary site: 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation and commissioning
User manual in English or translated into Russian language
Item
ITEM 22. HOT AIR STERILIZIATION
22.1.
Standard requirements
22.2.
Characteristics
Quantity
Quantity
6
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Hot air sterilizer with chamber volume: min 50 liters
Chamber made from stainless steel
Door with lateral opening with handling for safety against the
accidental opening
Selected programs for sterilization, heating or drying of materials
Min 3 working programs
Ventilation air system in spiral way to assure the temperature in
chamber
Control panel and LED,LCD display
Overheating protection system
Display of temperature and time
Accuracy ± 3 C
Indication of the already done and current sterilization phase
RS 232 – interface for printer or PC – communication - Optional
Acoustic alarm for overtake of programed temperature or other
error
Precise control of the sterilization cycle parameters with
microprocessor
Delayed heating start and stop function
Temperature sensor
Chrome plated trays – 2 pcs.
Working temperature: at least from 100C above ambient to 2500C
Time required to reach 2500C: max 60 min
28
Item
ITEM 22. HOT AIR STERILIZIATION
Quantity
6
Weight: max 75 kg
22.3.
Warranty and Service
Conditions
22.4.
Incidental Services
Power:
Power supply: 220 VAC, 50 Hz
24 months from the moment of installation
Maximum response time at beneficiary site: 48 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
ITEM 23. NEBULIZER FOR DRUGS
23.1.
Standard requirements
Quantity
5
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
23.2.
Technical
Characteristics
23.3.
Accessories and
Consumables
23.4.
Warranty and Service
Equipment for broncho-pulmonary pathologies: asthma,
pneumopathies, cystic fibrosis
Dedicated for all medicines: bronchodilators, antibiotics, corticoids,
and mucolytic
Running mode: the aerosol is produced continuous
Autoclavable up to 134oC
Preferable reusable accessories (tubes, masks)
Nebulizer:
Container capacity: approximately 5 ml
Equipped with tube with length approximately 1m
Multi position mask for adult and pediatric
Equipped with mouth end-piece and flask for dosage
Compressor:
Oil free
Maintenance free
Small dimensions (portable device)
Low weight (portable device)
Low noise device: approximate 30 dB
Pressure adjusted to 0.5 bar
Possibility to be fed by an oxygen central source: compressor flow
in charge with minimum 5l/min
Mouth end-piece – 5pcs
Nose plug – 2pcs
Nose piece – 2pcs
Masks adult – 2pcs
Masks pediatric – 5pcs
Period: 24 months from the moment of installation of the
29
Item
ITEM 23. NEBULIZER FOR DRUGS
Conditions
23.5.
Incidental Services
ITEM 24 GLUCOMETER
Standard requirements
24.2.
Technical
Characteristics
24.3.
Consumables
24.4.
Warranty and Service
Conditions
24.5.
Incidental Services
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Whole blood measurements
Measurement range: min 10 – 700 mg/dl
No light influence
Compensated with temperature influence
Serial imprecision: max 4 %
Strips for 500 of tests open market not limited to one company
Period: 24 months from the moment of installation of the
equipment
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
ITEM 25. SPHYNGOMANOMETER
Standard requirements
25.2.
Characteristics
Quantity
3
ITEM
25.1.
5
equipment
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
24.1.
Quantity
Quantity
12
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Digital Blood Pressure Monitor--Sphygmomanometer Upper Arm,
for neonates, infant, children and adults
Four mode for adult, pediatric ,infant, and neonatal selectable
Measures systolic, diastolic pressure, and pulse
Fully automatic one-touch operation
Automatic inflation and deflation
High resolution, large LCD display panel shows readings of blood
pressure, pulse rate
Optional 50 memories
30
ITEM
ITEM 25. SPHYNGOMANOMETER
25.3
Accessories
25.4.
Warranty and Service
Conditions
25.5.
Incidental Services
ITEM 26 REFRIGERATEUR
Standard requirements
26.2.
Technical
Characteristics
26.3.
Warranty and Service
Conditions
26.4.
Incidental Services
ITEM 27. STANDARD HOSPITAL BED WITH
MATTRESS
Standard requirements
Quantity
6
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Standard refrigerator
Capacity – 50 - 150 l
Built in single door
Temperature 0-4 C
Low power consumption
Electrical power connector should be standard type
Power supply 220V AC, 50 Hz
Period: 24 months from the moment of installation of the
equipment
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in Russian language
Item
27.1.
12
Cuff size
Neonate cuff size
Infant cuff size
Pediatric cuff size
Adult cuff size
AA Size Alkaline Battery and AC/DC Adapter
All cuff size neonates, infant, children and adult 1 pcs for each size
Other accessories and consumables if needed
24 months from the moment of installation
Maximum response time at beneficiary site: 48 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in English or translated into Russian language
Item
26.1.
Quantity
Quantity
20
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
31
Item
ITEM 27. STANDARD HOSPITAL BED WITH
MATTRESS
Technical
Characteristics
27.2
27.3.
Warranty and Service
Conditions
27.4.
Incidental Services
ITEM 28. HOSPITAL BEDSIDE CABINET
Standard requirements
28.2.
Technical
Characteristics
28.3.
Warranty and Service
Conditions
28.4.
Incidental Services
20
ISO 9001 certified companies
Standard hospital bed
Size approximately: 2000-2030/900-910/500 cm
Steel /Iron frame painted in electrostatic field with powder paint,
Stainless steel head and foot ends with vertical bars,
Mounted on protective stumps
Weight user max. ≥180kg.
2 section easy adjustable with handle
− back section lifting angle 75-80 grade
− foot section lifting angle 45 grade
Mattress compliant with bad size
Bed mattress cover antimicrobial, fire retardant, fluid-proof.
Period: 24 months from the moment of installation of the
equipment
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in Russian language
Item
28.1.
Quantity
Quantity
20
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Dimensions approximately:
− width: 400mm
− depth: 500mm
− height: 650mm,
1 drawer and 1 storage cabinet
Build in metal painted in electrostatic field
Color withe
Period: 24 months from the moment of installation of the
equipment
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in Russian language
32
Item
ITEM 29. DIGITAL WEGHING SCALE FOR NEONATES
29.1.
29.2.
Standard requirements
Technical
Characteristics
29.3.
Warranty and Service
Conditions
29.4.
Incidental Services
Quantity
10
1.Compliant to EU Medical devices Directives CE Mark
2. Compliant to IEC 60601 and amendments for Medical electrical
equipment
ISO 9001 certified companies
Digital Baby Scale for weighing neonates
Weigh up to 500 gr. to 10 kg./20 kg
Accuracy +/- 3%
Auto zero and auto off functions
Large LCD display
Operates on 120V/230V and rechargeable battery
Period: 24 months from the moment of installation of the
equipment
Maximum response time : 72 hours
Training for at least 2 medical personnel on site at beneficiary
location in Russian language
Training for at least 2 technical personnel on site at beneficiary
location in Russian language
Installation
User manual in Russian language
33
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement