Peavey T.B. RAXX Owner Manual

Peavey T.B. RAXX Owner Manual
OWNERS MANUAL
LB. RAXX
WARNING: TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. BEFORE USING THIS APPLIANCE,
READ THE OPERATING GUIDE FOR FURTHER WARNINGS.
FRONT PANEL
4 6 12
REE GAIN мани BA
á a NN - O O Ó ©: 00 ©
e © de E Г о % i 5
1 2 3 5 7 8 g 10 11 13
HIGH GAIN INPUT (1)
Used for most electric guitars. It is 6 dB louder than the Low Gain input.
LOW GAIN INPUT (2)
Provided for instruments that have extremely high outputs, which can result in overdriving (distorting) the High Gain input. If both
inputs are used simultaneously, the output levels are the same (both are Low Gain).
PRE GAIN CONTROL (3)
Controls the input volume level of the channel.
BRIGHT SWITCH (4)
Provides a preset boost (+/-8 dB) to treble frequencies. To activate, depress the switch to its “in” position.
GAIN BOOST SWITCH (5)
Boosts the overall system gain. Depress to the “in” position to activate.
LOW, MID £ HIGH EQ (6)
Passive tone controls that regulate the low, mid and high frequencies, respectively.
SHIFT (7)
Provides a special mid range equalization contour enhancing mid frequencies.
POST GAIN (8)
Controls the overall volume level of the channel. The final level adjustment should be made after the desired sound has been
achieved.
BOTTOM (9)
An active tone control (shelving type +/- 15 dB) that varies the low frequency boost or cut. NOTE: The action of this control is after
(post), the post gain control.
BODY (10)
An active tone control (peak/notch, +/- 15 dB) that varies the mid frequency boost or cut. NOTE: The action of this control is after
(post), the post gain control.
EDGE (11)
An active tone control (shelving type +/- 15 dB) that varies the high frequency boost or cut. NOTE: The action of this control is after
(post), the post gain control.
POWER LED (12)
llluminates when AC power is being supplied to the amp.
POWER SWITCH (13)
Depress to "On" position to turn on,
REAR PANEL
120 МА HKGH LEVEL LOW LEVEL
Ga Hz + 0 CHITPLIT TPUT
WARNING GUTPL
TOPREVENT RESK OF FIRE AND / À
no 1 TC ся ®
MOXSTURE Do HOT REWCWE COVER BG SEA
VICEABLE PARTS MSDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL A PRODUCTOR
AVIS: REQUE DE ÉHÔC ELECTAIQUE - NE Pé5 PEAVEY ELECTECAACS CORP. TES I'v TMS
40 WATTS CUVAIR. MERIDIAZ HS МАТЕМ НБА. [+10 HEN] 10 CEN
GROUND SWITCH (14)
Three position rocker-type switch which, in most applications, should be operated in its center or zero position. There may be
some situations when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch
to either positive or negative (+ or -) or until the noise is minimized. NOTE: Should the noise problem continue, consult your
Authorized Peavey Dealer, the Peavey Factory, or a qualified service technician. THE GROUND SWITCH IS NOT FUNCTIONAL
ON 220/240 VOLT MODELS.
LINE CORD (120V products only) (15)
For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is notadvisable to remove the
ground pin under any circumstances. If it is necessary to use the equipment without proper grounding facilities, suitable
grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with the proper
grounded receptacles.
LOW LEVEL OUTPUT (1 VOLT) (16)
A preamp output that can be used to route the preamp signal to a power amplifier, tape recorder, mixing console, effects device,
etc. Connect from the high level output to the input of the outboard device.
HIGH LEVEL OUTPUT (3 VOLTS) (17)
A preamp output that can be used to route the preamp signal to a power amplifier, crossover, etc. This output provides a 3-volt
signal level to drive “tube” power amplifiers and should not be used as an effects send to signal processors or effects devices.
METAL BASS (MILD DISTORTION)
A HPUTE =, GAR ——EOUALIZATION — —— Gan VOM
5 5 5 5 5 ü 0 о 7
OK EVE CITO Cr (= ©) (3 т
2 й 2 8 & B 2 i 2 3 a a § 2 8 a
8 i 5 1 B 1 5 12 1 л# 2 17 17
8 10 [| о 4 D "0 o 10 (I о 10 =15 15+ = а = 15e TE art.
CAN rt PRE BOOST LOW Mo HIGH Sort POST BOTTOM BODY EDGE TUBE BASS PREAMP
ADJUST TO TASTE
ROCK BASS (CLEAN)
y NPUTE A GAN ; и ЕСОЦАЦ АТК «
5 5 5 5
a NT [7 3, ы В 7 а, +
© e I a 2 ë = в 2 a
i a i | 1 q I в
a 0 [] Ú id nm 0 10
hoe в me goer on 0 we
COUNTRY
—— PUT a GAIN y EQUALIZATION. ——— GAIN и МОЖНО Ч *
É 5 5 5 E i ñ a ——
O © 3 4 6 (A @) O»; (a (С) (7) (7) (a / “el —
2 8 2 в 2 8 2 8 2 воз so 8 5 Ze
f i 9 1 7 12 12 1 а 12 2 7 Frere
В о u 3 16 a +0 e [| 0 =15 745% 15 18 8 5. "e Ratt. НЕ
а ca PRE Bor LOW MID MASA SHIFT POST BOTTOM BOY EDGE ' UBE BA - A
ADJUST TO TASTE
Tone settings given are general and will vary according to type of guitar, type and guages of strings, type of pickup and
even type of pick. Personal taste, playing style, and type of music greatly contribute to desired tonality.
SPECIFICATIONS
The following specs are measured @ LOW LEVEL OUTPUT:
1 kHz with the controls preset as follows: Load Impedance: 10K ohms or greater
Push Bright Off (Out) Nominal Output: 0 ABV, 1V RMS
Push Gain Boost Off (Out) Maximum Output: +10 d&V, 3V AMS
Low EQ @ 10 HIGH LEVEL OUTPUT:
Mid EQ @ 0 Load Impedance: 10K ohms or greater
High EQ @ 10 Nominal Output: +10 dav, av AMS
Push Shitt Off (Out) Maximum Output: +20 dBV, 10V RMS
Am OO a SYSTEM HUM & NOISE:
Body EQ @ 0 dB (with Pre Gain @ nominal setting)
Edge EQ @ 0 dB (20 Hz to 20 kHz unweighted)
Nominal levels are with pre gain @ 5 UL où 74 dE below nominal
Minimum levels are with pre gain @ 10 QUIPAIY levy
GAIN BOOST:
INSTRUMENT HIGH GAIN INPUT Ca
° EQUALIZATION:
Impedance: High Z, 1M ohm ;
Nominal Input Level: -10 dBV, 0.3V RMS Flush Bright. +8 cea
Minimum Input Level: -34 dBV swith O6 Gain. @ nommal setting)
20 mV RMS | Special low, mid 4 high passive type EQ
Maximum Input Level: O dBV, 1V AMS ideo pen Silt {pre dieron
INSTRUMENT LOW GAIN INPUT: Special bottom, body & edge active
Impedance: High Z, 44K ohms type EQ
Nominal Inpit Lever: -4 dBV, 0.6V RMS (+/- 15 dB range) (post distortion)
Minimum Input Level: -28 dev,
40 mv RMS
Maximum Input Level: +6 dBV, 2V RMS
BLOCK DIAGRAM
Push Bright
Equalization
input Tubs Tube
pu Stage | Stages
Push Shift Rn
THIS BLOCK DIAGRAM SHOWS THE SIGNAL PATH WITHIN THE AMPLIFIER. IN ORDER TO THOROUGHLY
UNDERSTAND THE FUNCTIONS OF THE AMPLIFIER, PLEASE STUDY THE BLOCK DIAGRAM CAREFULLY.
THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT TO
WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY.
Ces clauses de garantie ne sont vaiables qu'aux Etats-Unis et au Canada. Dans tous les autres pays, les clauses de garantie et de maintenance sont fixees par le distributeur national et
assurée par lui selon la legislation en vigueur.
Diese Garantie ist nur in den USA and Kanada guitig. Alle Export-Produkte sind der Garantie und dem Service des Importeurs des jewelligen Landes unterworfen.
Esta garantia es vallda solamente cuando el producto es comprado en E.U. continentales o en Canada. Todos los productos que sean comprados en el extranjero, estan sujetos alas
garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes paises.
ONE-YEAR LIMITED WARRANTY/REMEDY
PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material
and workmanship for a period of one (1) year from date of purchase, PROVIDED, however that this limited warranty is extended only to the original retail purchaser and is subjectto the
conditions, exclusions and limitations hereinafter set forth:
PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS
If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and work manship for a period of ninety (90)
days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions, exclusions and
limitations hereinafter set forth.
CONDITIONS, EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES
These limited warranties shall be void and of no effect if:
a. The first purchase of the product is for the purpose of resale; or
b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or
e. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance; or other causes not arising out of defects in material or
workmanship; or
d. The serial number affixed to the product is altered, defaced or removed.
In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will:
a. In the case of tubes or meters, replace the defective component without charge;
b. In other covered cases (i.e., cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanship or replace
the product, at Peavey s option;
and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser.
THEWARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROM THE
DATE OF YOUR PURCHASE.
In order to obtain service under these warranties, you must:
a. Bring the defective item to any AUTHORIZED PEAVEY DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF
PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product.
If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED DEALER or
AUTHORIZED PEAVEY SERVICE CENTER which can provide such service.
OR
©
. Ship the defective item, prepaid, to:
PEAVEY ELECTRONICS CORPORATION
— International Service Center
Highway 80 East
MERIDIAN, MS 32301
including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return address. Upon
Peavey's receipt of these items:
If the defect is remedial under these limited warranties and the other terms and conditions expressed herein have been complied with, Peavey will provide the necessary
warranty service 1o repair or replace the product and will return it, FREIGHT COLLECT, fo you, the purchaser.
Peavey's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the actual damages up to the
greater of $500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action. Such purchase
price will be that in effect for the specific product when the cause of action arose. This limitation of liability will not apply to claims for personal injury or damage to real property or
tangible personal property allegedly caused by Peavey's negligence. Peavey does not assume liability for personal injury or property damage arising out of or caused by a non-Peavey
alteration or attachment, nor does Peavey assume any responsibility for damage to interconnected non-Peavey equipment that may result from the normal functioning and
maintenance of the Peavey equipment,
UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES OR ANY CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE: PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO THE EXISTENCE OF
THE EXPRESS, LIMITED WARRANTIES, AS HEREINABOVE STATED, HAVE BEEN COMPLIED WITH, IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE
APPLICABLE ONE-YEAR OR NINETY-DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT.
SOMESTATESDONOTALLOWLIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, 50 THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
THESE LIMITED WARRANTIES ARE THE ONLY EXPRESS WARRANTIES ON THIS PRODUCT, AND NO OTHER STATEMENT, REPRESENTATION, WARRANTY OR
AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY.
In the event of any modification or disclaimer of express or implied warranties, or any limitation of remedies, contained herein conflicts with applicable law, then such modification,
disclaimer or limitation, as the case may be, shall be deemed to be modified to the extent necessary to comply with such law.
Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to
equipment purchased in the United States of America.
INSTRUCTIONS — WARRANTY REGISTRATION CARD
1. Mail the completed WARRANTY REGISTRATION CARD to;
PEAVEY ELECTRONICS CORPORATION
POST OFFICE BOX 2898
MERIDIAN, MISSISSIPPI 39302-2898
a. Keep the PROOF OF PURCHASE. In the event warranty service is required during the warranty period, you will need this document. There will be no identification card
issued by Peavey Electronics Corporation.
2. IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESS:
a. Completion and mailing of WARRANTY REGISTRATION CARDS — Should notification become necessary for any condition that may require correction, the REGISTRATION
CARD will help ensure that you are contacted and properly notified.
b. Notice of address changes — If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of address so as to
facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of
information or correction,
3. You may contact Peavey directly by telephoning (601) 483-5365.
4. Please have the Peavey product name and serial number available when communicating with Peavey Customer Service.
DANGER
EXPOSURE TO EXTREMELY HIGH NOISE LEVELS MAY CAUSE A PERMANENT HEARING LOSS, INDIVIDUALS VARY CONSIDERABLY IN SUSCEPTIBILITY TO NOISE INDUCED HEARING LOSS, BUT NEARLY
EVERYONE WILL LOSE SOME HEARING IF EXPOSED TO SUFFICIENTLY INTENSE NOISE FOR A SUFFICIENT TIME.
THE U.S. GOVERNMENT'S OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) HAS SPECIFIED THE FOLLOWING PERMISSIBLE NOISE LEVEL EXPOSURES:
DURATION PER DAY IN HOURS
far futura ra ATOR
3. Obay all cautions in the operating instructions and on the
back of the unit.
SOUND LEVEL dBA, SLOW RESPONSE
| MT ihe ground pin diibower supply HEHE:
Fo В information on me ng wrile for our free
booklet "Shock Hazard and Grounding.”
. Power supply cords should always be handled Get
ts do not fall and
14. Care should be taken so thal obj
liquids are not spilled into the unit through the ventilation
holes or any other openings.
1 Mewar walk or place equipment on power supply cords, :
4. All operating instructions should be followed. | Periodically Le dr for or fir i 15: This unit ehodid- be chécked bye: qualified-serice
5. This product should mot be used near water, 1a. a expecially at the plug and the point where the cord exits technician if.
bathiub, sink, swimming pool, wet basement, etc. tha unit. А The power supely CAO EP PIS ONE baer. daira :
6. This product should be located so that its position does 1. The power supply cord should be unplugged when the B. Anything has fallen or been spilled Into the uni
placed fat againat a vell or placedin a bulit-in enclosurs unit © be unused for ong periods of mo D. FR Ua rotor cono mage
pla at against a placed in a -im enclosure |
that will impede the flow of cooling air. 2 EA hey IAT [email protected] ERAI 16. The user should not lo atlempt to service this equipment,
7. This product should not be placed near a source of heat All service work should be done by a qualified service
such as a stove, radiator or another heat producing technician,
amplifier.
EA
2d
Features and specifications subject to change without notice.
Peavey Electronics Corporation / 711 A Street / Meridian, MS 39302-2898 / U.S.A. / (601) 483-5365 Telex: 504115 / Fax: 484-4278
©1989 Printed in the U.S.A.
#80301108 10/89
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement