MM CASA INC

CS-VC109

Instruction Manual

contents

Product Introduction

Product Operation

Product Maintenance

Trouble Shooting

Safety Introduction

Product Parameters

Product Introduction

1 Main Body

2 TYPE-C charge cable

3 2 in 1 flat sucker

4 Hose suction nozzle

5 Blowing nozzle

Tips ： When cleaning dust, accessories 3,4 can be installed on 1

Tips ： When blowing dust, accessories 5 can be installed on 1

Product Operation

一：

Charging

The battery is not charged at the factory, be sure to fully charge the battery before use.

1 、 Place the main body on a horizontal countertop （ Please place the end of the lanyard on the table top ）

2 、 Connect the USB cable with the charging port on the main body to start charging ,and power indicator flashes,after full charge,the indicator light is always on.

3 、 Charging time: 3.5 hours. Using time: high speed 12 min, low speed 25mins.

Attention ：

1. Do not charge at temperatures below 5 ℃ or above 40 ℃

2.

When the product is low in power during operation, the power indicator light will flash

二：

Cleaning

To prevent blockage of the air passage, large objects like large paper and packing materials should be removed from the area before start cleaning

1 、 Press the start button to start cleaning,power indicator light will always on.

2 、 Press again the start button to stop cleaning,power indicator light will off.

3 、 Press the speed control button to choose high or low speed when the machine is working.

4 、 When the machine is working, the battery indicator is always on. When the battery indicator is flashing, please pay attention to timely charging.

三： Replacing Accessories

A

: replacing 2 in 1 Flat Brush

① Insert the flat tube into the suction port in the direction shown in the figure (the larger step of the flat tube faces upward).

② When you need to use the brush, turn the brush in the direction as shown in the figure, and it can be used when it is turned horizontally.

B:

Replace hose nozzle

①

Insert the flat tube into the suction port in the direction shown in the figure

(the larger step of the flat tube faces upward).

C:

Replace the blowing nozzle

①

According to the direction shown in the figure, put the lanyard into the blowing nozzle or remove the lanyard, and put the blowing nozzle on the air outlet.

Replacing battery

Tips: If you need to replace the battery please consult your dealer.

Battery is consumable. If the battery life becomes shorter and charging time becomes longer, please replace the battery pack.

Indicator light description ：

A 、 Press start button, the machine starts working,power indicator light on,it is low speed now,press speed control button to change speed.

B 、 The power indicator lights are flashing when charging,and the power indicator lights will all be on after fully charged;the power indicator light will always on when full charged,when power indicator flash,means low power, please pay attention to charging timely .

C 、 When the abnormal warning indicator light is on, please clean the machine immediately;It is recommended to clean the machine after each use.

Warning:

1.The machine must be turned off during charging;

2.Do not use and store batteries at temperatures below 5 ℃ or above 40 ℃ ;

3.When disposing of this product, remove the battery from the device;

4.Do not modify the device ,accessories or replace the power cord or battery;

5.Battery Model ： DYDC-L04 11.1V

Battery recycling

:

Waste batteries are important resources. When disposing of the product, do not

dispose of the battery at will. Please treat properly in accordance with government regulations to facilitate the recovery to the corresponding waste battery recycling facilities.

Maintenance

1.

Press the dust cup button, the suction mouth will open automatically, and the garbage will be poured out

Dust cup button

2.

Put the suction mouth back on

3.

Unscrew the dust cup clockwise (the "O" on the main body is aligned with the " ▲ " on the dust cup), then, take out the dust cup downward

4.

Remove the HEPA filter assembly from the dust cup

Hold it here and lift it

5.

Turn counterclockwise and take out the filter, separating the HEPA from the filter

HEPA

Filter

6.

Clean the dust cup, HEPA and filter screen with a brush or paper towel. If necessary, clean with water directly

7.

Remove the back cover by turning it counterclockwise

8.

Remove the outlet air filter cotton and clean it up outlet air filter cotton

9. After the parts are fully dried, they can be put back according to the disassembly procedure tips ： It is recommended to carry out the above cleaning work after the dust is dumped each time.

Attention

1.Please pay attention to sharp objects such as glass to prevent injury.

2.The parts must be completely dry before installing.

3.Do not scrub the filter cotton or apply brute force to it

4.Please make sure that the filter cotton has been installed before assembly.

5.Do not continue to use when the filter cotton in the dust cup is damaged or if the cleaning and maintenance are not sufficient.

TROUBLESHOOTING

In case of malfunction ,please refer to the following table

Problem

Running time becomes shorter

Suction power becomes weak

Can’t charge

Battery leakage

Possible reason

Ambient temperature is too high or too low

The battery isn’t fully charged

Too much dust in the cup

Cotton filter is blocked

Brush or accessory suction port is blocked

Hasn’t been fully dried after washing

Ambient temperature is too high or too low

The battery has not been used for a long time

Solution

Use in appropriate environment

Please charge the battery

Clean in time

Wash the cotton filter

Clear the blockage

Dry the part in cool place after washing

Charge in appropriate environment （ 5 ℃ -40 ℃） replace battery

*For other malfunctions that cannot be handled, please contact the local after-sales service outlets or call the national service hotline.

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Safety Introduction

Only the certified technician may disassemble this product, Users are strictly not allowed to disassemble this product.

This product shall only bi charged using the included power adapter ,Other power adapters may cause damages to this product.

Do not touch power cord ,plug or adapter with wet hands.

Avoid curtains ,any kind of strings or user/s body part wrapping up on the wheel.

Keep this product away from cigarette stubs ,lighters or flame.

To clean the product ,this product must be fully charged before any cleaning process.

Do not over-bend the power cord ,or place heavy or sharp objects on this product.

This product is intended for indoor use only ,do not use this product outdoors.

Do not place object(e.g. human) with more than 10KG weight on this product.

Do not use this product in wet or moist environment(e.g. bathroom).

Before using this product ,please remove any fragile objects(e.g. glasses, lamps etc)from the floor. Also removes any objects that may be wrapped up to the side brushes or may block the suction inlet.

Do not put this product on position where is east to fall off.

While delivering or if for not use the product for long time ,please turn it off from the bottom.

Before charging, please check whether the power adapter and socket is connected well.

When this product is cleaning the room ,please inform other members to avoid causing then to fall.

When the dust bin is full of dust, empty the dust bin before using this product.

This product is functioning at temperature range within 5 ℃ to 40 ℃ .

Do not use this product in high-temperature environment.

Please remove batteries from this product before disposal.

Product Parameters

Product Technical Parameters

Model

CS-VC109

Rated Charging Voltage

5VDC/2A

Rated voltage

11.1V

Rated Power

100W