F20196C EN.qxd:F20196C.qxd

F20196C EN.qxd:F20196C.qxd
Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking web site at
vikingrange.com
Microwave Built-In Trim Kit
F20196C EN
TINSEB453MRRO
(010708J)
IMPORTANT - PLEASE READ AND FOLLOW
BASIC SPECIFICATIONS
•Before beginning, please read these instructions completely and carefully.
•Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit. Remove
the turntable from the oven cavity.
•Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
•Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
•Please observe all local and national codes and ordinances.
•The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future
reference.
Microwave Oven
VMOS200
VMTK270/271
Built-In Trim Kits
VMTK300/301
VMTK360/361
Overall Width
24” (60.9 cm)
26-1/2” (67.3 cm)
29-1/2” (74.9 cm)
35-1/4” (89.5 cm)
Overall Height from Bottom
13-3/8” (33.9 cm)
18-1/4” (46.3 cm)
18-1/4” (46.3 cm)
18-1/4” (46.3 cm)
Overall Depth from Rear
19-3/8” (49.2 cm)
N/A
N/A
N/A
Oven Interior
Width - 17-3/8” (44.1 cm)
N/A
N/A
N/A
Height - 10-1/2” (26.6 cm)
Depth - 18-5/8” (47.3 cm)
THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY WITH VIKING MICROWAVE OVENS SPECIFYING BUILT-IN KIT
VMTK270/271, VMTK300/301, OR VMTK360 FOR PROFESSIONAL UNITS AND DMTK270 OR DMTK300 FOR
DESIGNER UNITS ON THE RATING LABEL ON THE LEFT SIDE WALL OF THE OVEN CAVITY.
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
PARTS INCLUDED IN THE VMTK KIT
1) Front Frame Assembly
PARTS INCLUDED IN THE DMTK KIT
- QTY 1
1) Frame Assembly
- QTY 1
Front Frame Sub-Assembly;
Back Frame Sub-Assembly
2) Exhaust Duct Assembly
2) Exhaust Duct Assembly
- QTY 1
- QTY 1
Overall - 2.0 cu. ft.
Cutout Width
N/A
Min. - 24-3/8” (61.9 cm)
Max. - 24-11/16” (62.7 cm)
Cutout Height
N/A
Min. - 16-3/4” (42.5 cm)
Max. - 17” (43.2 cm)
Cutout Depth
N/A
Min. 20” (50.8 cm)
Electrical Requirements
120VAC/60 Hz
N/A
N/A
N/A
Max. Amp Usage
1.65 KW; 13.5 amps
N/A
N/A
N/A
Approximate Shipping Wt.
55 lbs. (24.7 kg)
14 lbs. (6.5 kg)
15 lbs. (6.9 kg)
16 lbs. (6.9 kg)
Microwave Oven
DMOS200
DMTK270
Overall Width
24” (60.9 cm)
26-1/2” (67.3 cm)
29-1/2” (74.9 cm)
Overall Height from Bottom
13-3/8” (33.9 cm)
18-1/4” (46.3 cm)
18-1/4” (46.3 cm)
Overall Depth from Rear
19-3/8” (49.2 cm)
N/A
N/A
Oven Interior
Width - 17-3/8” (44.1 cm)
N/A
N/A
Built-In Trim Kits
DMTK300
Height - 10-1/2” (26.6 cm)
3) Screw A (1/2” length)
Depth - 18-5/8” (47.3 cm)
- QTY 2
Overall - 2.0 cu. ft.
3) Screw A (1/2” length)
Cutout Width
- QTY 2
4) Screw B (1 1/2” length)
N/A
Min. - 24-3/8” (61.9 cm)
Max. - 24-11/16” (62.7 cm)
- QTY 4
Cutout Height
N/A
Min. - 16-3/4” (42.5 cm)
Max. - 17” (43.2 cm)
4) Screw B (1 3/4” length)
- QTY 4
5) Screw C (3/8” length)
2
- QTY 4
Cutout Depth
N/A
Min. 20” (50.8 cm)
Electrical Requirements
120VAC/60 Hz
N/A
N/A
Max. Amp Usage
1.65 KW; 13.5 amps
N/A
N/A
Approximate Shipping Wt.
55 lbs. (24.7 kg)
14 lbs. (6.5 kg)
15 lbs. (6.9 kg)
3
CABINET OR WALL CUTOUT
CABINET INSTALLATION
Cutout Dimensions
1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet.
Height (A)
Minimum
Maximum
Width (B)
Minimum
Maximum
Depth (C)
Minimum
2. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct Assembly. See
Illustration 3. Avoid pinching the cord between the oven and the wall. Adjust the position of the oven so that the
feet of the oven are fitted into the recesses of the Exhaust Duct Assembly. See Illustration 4.
16 3/4” (42.5 cm)
17” (43.2 cm)
24 3/8” (61.9 cm)
24 11/16” (62.7 cm)
Illustration 4
20” (50.8 cm)
ELECTRICAL OUTLET LOCATION
Illustration 3
Outlet should NOT be in the shaded area as
indicated on Illustration 1
6”
(15.2 cm)
NOTE 1: If the Depth (C) dimension is greater
than 21” (53.3 cm), the outlet location may be in
any area on the rear wall.
OVEN
SIDE
4”
(10.2 cm)
NOTE 2: The floor of the opening should be
constructed of plywood strong enough to support
the weight of the oven and floor load
(approximately 100 pounds). The floor should be
level for proper operation of the oven. Be sure to
check the local building code as it may require that
the opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven does
not require the enclosure.
Foot
Recess
Exhaust Duct Assembly
4”
(10.2 cm)
FRAME INSTALLATION
VMTK ONLY
Illustration 1
EXHAUST DUCT ASSEMBLY
1. Place the Exhaust Duct in the opening.
When the Exhaust Duct Assembly is in the
opening correctly, the flanges will be tightly
against the lower edge of the opening. See
Illustration 2.
2. Secure the Exhaust Duct Assembly with the
two (1/2”) screws A. IMPORTANT: Secure
screws in outer hole.
Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven.
Check that it is level and then secure with two SCREWS B. See Illustration 5. Secure the bottom portion of the FRAME
ASSEMBLY with the two remaining SCREWS B. See Illustration 5.
Illustration 2
Illustration 5
Screw B
Flanges
Screw B
Screw B
Exhaust Duct Assembly
Screw A
Screw B
Detail A
4
5
OVER OVEN INSTALLATION
DMTK270 ONLY
DMTK300 ONLY
Position the BACK FRAME ASSEMBLY to be square with
the oven. Carefully place the BACK FRAME ASSEMBLY
on the oven. Check that the oven is level and secure the
lower portion FIRST with two of the Screw B. Adjusting
the BACK FRAME ASSEMBLY up or down may be
necessary in order to locate the thru holes on the exhaust
duct assembly. Secure the upper portion of the BACK
FRAME ASSEMBLY with the remaining Screw B. See
Illustration 5
Position the BACK FRAME ASSEMBLY to be square with
the oven. Carefully place the BACK FRAME ASSEMBLY
on the oven. Check that the oven is level and secure the
upper portion FIRST with two of the Screw B. Secure the
bottom portion of the BACK FRAME ASSEMBLY with the
remaining two Screws B. See Illustration 5
2” (5.1 cm) For 27” W. and 30” W. lower oven
4” (10.2 cm) For 36” W. lower oven
Illustration 5
Screw B
Place the FRONT FRAME ASSEMBLY through the microwave onto the BACK FRAME ASSEMBLY. Secure the FRONT
FRAME ASSEMBLY to the BACK FRAME ASSEMBLY with Screws C. See Illustration 6
NOTE: The center tab denotes correct orientation of the FRONT FRAME. See Detail B.
Illustration 6
Detail B
Screw C
6
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement