Manual coating equipment OptiFlex 2 Q

Manual coating equipment OptiFlex 2 Q
1010 267
En
Operating instructions and spare parts list
Manual coating equipment
OptiFlex 2 Q
Translation of the original operating instructions
V 08/15
Documentation OptiFlex 2 Q
© Copyright 2010 Gema Switzerland GmbH
All rights reserved.
This publication is protected by copyright. Unauthorized copying is
prohibited by law. No part of this publication may be reproduced,
photocopied, translated, stored on a retrieval system or transmitted in
any form or by any means for any purpose, neither as a whole nor
partially, without the express written consent of Gema Switzerland
GmbH.
MagicCompact, MagicCylinder, MagicPlus, MagicControl, OptiFlex,
OptiControl, OptiGun, OptiSelect, OptiStar and SuperCorona are
registered trademarks of Gema Switzerland GmbH.
OptiFlow, OptiCenter, OptiMove, OptiSpeeder, OptiFeed, OptiSpray,
OptiSieve, OptiAir, OptiPlus, OptiMaster, MultiTronic, EquiFlow, Precise
Charge Control (PCC), Smart Inline Technology (SIT) and Digital Valve
Control (DVC) are trademarks of Gema Switzerland GmbH.
All other product names are trademarks or registered trademarks of their
respective holders.
Reference is made in this manual to different trademarks or registered
trademarks. Such references do not mean that the manufacturers
concerned approve of or are bound in any form by this manual. We have
endeavored to retain the preferred spelling of the trademarks, and
registered trademarks of the copyright holders.
To the best of our knowledge and belief, the information contained in this
publication was correct and valid on the date of publication. Gema
Switzerland GmbH makes no representations or warranties with respect
to the contents or use of this publication, and reserves the right to revise
this publication and make changes to its content without prior notice.
For the latest information about Gema products, visit
www.gemapowdercoating.com.
For patent information, see www.gemapowdercoating.com/patents or
www.gemapowdercoating.us/patents.
Printed in Switzerland
Gema Switzerland GmbH
Mövenstrasse 17
9015 St.Gallen
Switzerland
Phone: +41-71-313 83 00
Fax.: +41-71-313 83 83
E-Mail: [email protected]
V 08/15
Table of contents
General safety regulations
3
Safety symbols (pictograms)................................................................................... 3
Proper use............................................................................................................... 8
Product-specific safety measures ........................................................................... 8
OptiFlex 2 Q Manual coating equipment ................................................... 8
About this manual
9
General information ................................................................................................ 9
Product description
11
Field of application ................................................................................................ 11
Utilization.................................................................................................. 11
Reasonably foreseeable misuse .............................................................. 12
Technical data ....................................................................................................... 12
Connectable guns .................................................................................... 12
Powder output (guide values) .................................................................. 12
Guide values for OptiStar CG13 with OptiFlow Injector IG06.................. 13
Air flow rates ............................................................................................ 13
Electrical data .......................................................................................... 13
Pneumatic data ........................................................................................ 14
Dimensions .............................................................................................. 14
Processible powders ................................................................................ 14
Design and function .............................................................................................. 15
General view ............................................................................................ 15
Scope of delivery .................................................................................................. 16
OptiFlex 2 Q ............................................................................................. 16
Typical properties – Characteristics of the functions ............................................ 16
Processing the powder directly from the original powder manufacturer's
container .................................................................................................. 16
Freely rotating head piece ....................................................................... 16
Commissioning
17
Preparation for start-up ......................................................................................... 17
Basic conditions ....................................................................................... 17
Set-up.................................................................................................................... 17
Mounting instructions ............................................................................................ 18
Connection instructions ......................................................................................... 19
Initial start-up
21
Set head piece ...................................................................................................... 22
Setting the device type .......................................................................................... 22
Operation .............................................................................................................. 23
Coating ..................................................................................................... 23
Setting the background illumination ......................................................... 27
Color change ......................................................................................................... 28
General information ................................................................................. 28
Shutdown .............................................................................................................. 30
OptiFlex 2 Q
Table of contents • 1
V 08/15
Cleaning and maintenance
31
Daily maintenance ................................................................................................ 31
Weekly maintenance ............................................................................................ 31
If in disuse for several days .................................................................................. 31
Powder hose rinsing ................................................................................ 31
Cleaning................................................................................................................ 32
Cleaning the fluidizing/suction unit .......................................................... 32
Cleaning the OptiSelect GM03 manual powder gun ............................... 32
Maintenance and cleaning of the filter unit ........................................................... 33
Replacing the filter element ..................................................................... 33
Fault remedying
35
General information .............................................................................................. 35
Spare parts list
37
Ordering spare parts............................................................................................. 37
OptiFlex 2 Q - Spare parts list .............................................................................. 38
OptiFlex 2 Q - Spare parts list .............................................................................. 39
OptiFlex 2 Q Dual Gun - Spare parts list .............................................................. 40
OptiFlex 2 Q – Pneumatic group .......................................................................... 41
OptiFlex 2 Q Dual Gun - Pneumatic group........................................................... 42
2 • Table of contents
OptiFlex 2 Q
V 08/15
General safety regulations
This chapter sets out the fundamental safety regulations that must be
followed by the user and third parties using OptiFlex 2 Q manual coating
equipment.
These safety regulations must be read and understood before the
OptiFlex 2 Q is put into operation.
Safety symbols (pictograms)
The following warnings with their meanings can be found in the Gema
operating instructions. The general safety precautions must also be
followed as well as the regulations in the operating instructions.
DANGER!
Danger due to electrically live or moving parts. Possible consequences:
death or serious injury
WARNING!
Improper use of the equipment could damage the machine or cause it to
malfunction. Possible consequences: minor injuries or damage to
equipment
INFORMATION!
Useful tips and other information
OptiFlex 2 Q
General safety regulations • 3
V 08/15
The OptiFlex 2 Q manual coating equipment is state of the art equipment
that conforms to the recognized technical safety regulations and is
designed for normal powder coating applications.
General
information
Any other use is considered non-compliant. The manufacturer shall not
be liable for damage resulting from such use; the user bears sole
responsibility for such actions. Gema Switzerland GmbH must be
consulted before OptiFlex 2 Q manual coating equipment is used for any
other purposes or substances beyond those indicated here.
Observance of the operating, service and maintenance instructions
specified by the manufacturer is also part of conformity of use.
The relevant accident prevention regulations, as well as other generally
recognized safety regulations, occupational health and structural
regulations are to be observed.
Furthermore, the country-specific safety regulations also must be
observed.
Additional safety and operation notices can be found on the
accompanying CD or on the homepage www.gemapowdercoating.com.
Start-up is forbidden until it has been established that the OptiFlex 2 Q
manual coating equipment has been set up and wired according to the
EU guidelines for machinery.
Unauthorized modifications to the OptiFlex 2 Q Manual coating
equipment exempt the manufacturer from any liability from resulting
damages or accidents.
General
dangers
The operator must ensure that all users have received appropriate
training for powder spraying equipment and are aware of the possible
sources of danger.
Any operating method, which will negatively influence the technical safety
of the powder spraying equipment, is to be avoided.
4 • General safety regulations
OptiFlex 2 Q
V 08/15
For your own safety, only use accessories and attachments listed in the
operating instructions. The use of other parts can lead to risk of injury.
Only original Gema spare parts should be used!
Repairs must only be carried out by specialists or by authorized Gema
service centers. Unauthorized conversions and modifications can lead to
injuries and damage to the equipment, and the Gema Switzerland GmbH
guarantee would no longer be valid.
The connecting cables between the control unit and the spray gun must
be installed so as to eliminate the possibility of damage during the
operation. Please observe the local safety regulations!
The plug connections between the powder spraying equipment and the
mains should only be removed when the power supply is switched off.
Electrical
danger
All maintenance activities must take place when the powder spraying
equipment is switched off.
The powder coating equipment may not be switched on until the booth is
in operation. If the booth stops, the powder coating device must switch off
too.
The control units for the spray guns must be installed and used in zone
22. Spray guns are allowed in zone 21.
Only original Gema OEM parts are guaranteed to maintain the explosion
protection rating. If damages occur related to the use of spare parts from
other manufacturers, all relevant warranty or compensation claims are
void!
Explosion hazard
Conditions leading to dangerous levels of dust concentration in the
powder spraying booths or in the powder spraying areas must be
avoided. There must be sufficient technical ventilation available, to
prevent a dust concentration of greater than 50% of the lower explosion
limit (UEG = max. permissible powder/air concentration). If the UEG is
not known, then a value of 10 g/m³ should be considered (see EN
50177).
All unauthorized conversions and modifications to the electrostatic
spraying equipment are forbidden for safety reasons.
The safety devices may not be dismantled or put out of operation.
Mandatory operational and workplace notices from the operating
company must be written in a comprehensible manner in the language of
equipment operators and posted in a suitable place.
OptiFlex 2 Q
General safety regulations • 5
V 08/15
Powder lying on the floor around the powder spraying equipment is a
potentially dangerous source of slipping. Booths may be entered only in
the places designed for this purpose.
Slip hazard
Static charges
Static charges can have the following consequences: Charges to people,
electric shocks, sparking. Proper grounding must be in place to prevent
objects from becoming charged.
Earthing
All electrically conductive parts found within 5 meters around each booth
opening, and in particularly the objects to be coated, must be grounded.
The grounding resistance of each object must amount to maximally 1
MOhm. This resistance must be checked/tested regularly when starting
work.
Observe the
grounding
regulations
The condition of the work piece attachments, as well as the hangers,
must guarantee that the work pieces remain grounded. The appropriate
measuring devices must be kept ready in the workplace, in order to
check the grounding.
The floor of the coating area must conduct electricity (normal concrete is
generally conductive).
The supplied grounding cable (green/yellow) must be connected to the
grounding screw of the electrostatic manual powder coating equipment.
The grounding cable must have a good metallic connection with the
coating booth, the recovery unit and the conveyor chain, respectively with
the suspension arrangement of the objects.
Smoking and igniting fire are forbidden in the entire vicinity of the system!
No work that could potentially produce sparks is allowed!
Fire and smoke
prohibition
6 • General safety regulations
OptiFlex 2 Q
V 08/15
The stay for persons
with cardiac
pacemakers is
forbidden
Photographing with
flashlight is
forbidden
As a general rule for all powder spraying installations, persons with
pacemakers should never enter high voltage areas or areas with
electromagnetic fields. Persons with pacemakers should not enter areas
with powder spraying installations!
Photographing with flashlight can lead to unnecessary releases and/or
disconnections by safety devices.
Disconnect the plugs before the machines are opened for maintenance
or repair.
Disconnect from
mains before
maintenance works
take place
The plug connections between the powder spraying equipment and the
mains should only be removed when the power supply is switched off.
As far as it is necessary, the operating firm must ensure that the
operating personnel wear protective clothing (e.g. facemasks).
A dust mask corresponding to filter class FFP2 at minimum must be worn
during any cleaning work.
The operating personnel must wear electrically conductive, steel-toe
footwear (e.g. leather soles).
The operating personnel should hold the gun with bare hands. If gloves
are worn, these must also conduct electricity.
These general safety regulations must be
read and understood in all cases prior to
start-up!
OptiFlex 2 Q
General safety regulations • 7
V 08/15
Proper use
1. The OptiFlex 2 Q manual coating equipment is state of the art
equipment that conforms to the recognized technical safety
regulations and is designed for normal powder coating
applications.
2. Any other use is considered non-compliant. The manufacturer
shall not be liable for damage resulting from such use; the user
bears sole responsibility for such actions. Gema Switzerland
GmbH must be consulted before OptiFlex 2 Q manual coating
equipment is used for any other purposes or substances beyond
those indicated here.
3. Observance of the operating, service and maintenance
instructions specified by the manufacturer is also part of
conformity of use. The OptiFlex 2 Q manual coating equipment
should only be used, maintained and started up by trained
personnel informed and familiar with the possible hazards
involved.
4. Start-up (i.e. operation of its intended use) is not allowed until it
has been established that the OptiFlex 2 Q manual coating
equipment has been installed and wired according to the EU
Machinery Directive (2006/42/EC). EN 60204-1 (machine safety)
must also be observed.
5. Unauthorized modifications to the OptiFlex 2 Q manual coating
equipment exempt the manufacturer from any liability from
resulting damage.
6. The relevant accident prevention regulations, as well as other
generally recognized safety regulations, occupational health and
structural regulations are to be observed.
7. Furthermore, the country-specific safety regulations also must be
observed.
Product-specific safety measures
-
Installation work performed by the customer must be carried
out according to local regulations.
-
All components must be grounded according to the local
regulations before start-up.
OptiFlex 2 Q Manual coating equipment
The OptiFlex 2 Q manual coating equipment is a constituent part of the
equipment and is therefore integrated in the system's safety concept.
If it is to be used in a manner outside the scope of the safety concept,
then corresponding measures must be taken.
NOTE:
For further security information, see the more detailed Gema safety
regulations!
8 • General safety regulations
OptiFlex 2 Q
V 08/15
About this manual
General information
This operating manual contains all important information required to work
with the OptiFlex 2 Q manual coating equipment. It will safely guide you
through the start-up process and give you references and tips for the
optimal use of your new powder coating system.
Information about the functionality of the individual system components booth, gun control unit, manual gun or powder injector - should be
referenced to their enclosed corresponding documents.
NOTE:
This operating manual describes all options and functions of this
manual coating equipment.
► Please note that your manual coating equipment may not be equipped
with all described functions.
► Options are marked by double asterisks**.
DANGER:
Working without operating instructions
Working without operating instructions or with individual pages
from the operating instructions may result in damage to property
and personal injury if relevant safety information is not observed.
► Before working with the device, organize the required documents and
read the section "Safety regulations".
► Work should only be carried out in accordance with the instructions of
the relevant documents.
► Always work with the complete original document.
OptiFlex 2 Q
About this manual • 9
V 08/15
Product description
Field of application
The OptiFlex 2 Q (with powder box) manual coating equipment is
exclusively intended for electrostatic coating using organic powders (For
more on this please also review chapter "Technical Data").
Any other use is considered non-compliant. The manufacturer is not
responsible for any incorrect use and the risks associated with such
actions are assumed by the user alone!
For a better understanding of the interrelationships in powder coating, it
is recommended that the operating instructions for all other components
be read as well, so as to be familiar with their functions too!
OptiFlex 2 Q Manual coating equipment
Utilization
The electrostatic OptiFlex 2 Q manual coating equipment with the
OptiSelect GM03 manual powder gun is ideally suited for manual coating
of objects.
OptiFlex 2 Q
Product description • 11
V 08/15
Reasonably foreseeable misuse
-
Operation without the proper training
-
Use with insufficient compressed air quality and grounding
-
Use in connection with unauthorized coating devices or
components
Technical data
Connectable guns
OptiFlex 2 Q
connectable
OptiSelect GM03
yes
WARNING:
The OptiFlex 2 Q manual coating equipment can only be used with
the specified gun type!
Powder output (guide values)
General conditions for the OptiFlow Injector
Powder type
Powder hose length (m)
6
Powder hose Ø (mm)
10
Power hose type
Input pressure (bar)
Conveying air nozzle Ø (mm)
Correction value C0
12 • Product description
Epoxy/polyester
POE with guide strips
5.5
1.6
Powder output zeroing adjustment
OptiFlex 2 Q
V 08/15
Guide values for OptiStar CG13 with OptiFlow
Injector IG06
All values in these tables are guide values. Differing environmental
conditions, wear and different powder types can affect the table values.
3 Nm³/h
Total air
4 Nm³/h
5 Nm³/h
Powder output (g/min)
Powder output
(%)
20
40
60
80
100
85
150
210
270
300
100
185
255
320
360
120
210
280
350
395
Air flow rates
The total air consists of conveying air and supplementary air, in relation
to the selected powder quantity (in %). As a result the total air volume is
maintained constant.
Range
Factory
setting
- OptiFlex 2 Q
0-1.0 Nm³/h
0.1 Nm³/h
Electrode rinsing air flow rate
0-3.0 Nm³/h
0.1 Nm³/h
OptiFlex 2 Q
Flow rate - fluidizing air
Flow rate total air (at 5.5 bar)
1.8-6.5 Nm³/h
NOTE:
The total air consumption for the device is determined based on the
3 configured air values.
These values apply for an internal control pressure of 5.5 bar!
Electrical data
OptiFlex 2 Q
Nominal input voltage
Frequency
50-60 Hz
Connected load (without vibrator)
140 VA
Nominal output voltage (to the gun)
eff.10 V
Nominal output current (to the gun)
max. 1.2 A
Connection and output for vibrator (on Aux
output)
Connection for rinsing function (valve)
110/230 VAC
max. 100 W
24 VDC
max. 3 W
Temperature range
0 °C - +40 °C
(+32 °F - +104 °F)
Max. surface temperature
120 °C (+248 °F)
Approvals
OptiFlex 2 Q
100-240 VAC
II 3 D IP54 120 °C
Product description • 13
V 08/15
Pneumatic data
OptiFlex 2 Q
Max. input pressure
10 bar
Min. input pressure
6 bar
Input pressure (Dynamic based on pressure
regulator setting)
5.5 bar / 80 psi
Max. water vapor content of the compressed
air
1.3 g/m³
Max. oil vapor content of the compressed air
0.1 mg/m³
Max. compressed air consumption
8 Nm³/h
Dimensions
OptiFlex 2 Q
Width
460 mm
Depth
862 mm
Height
1105 mm
Weight
42 kg
Processible powders
OptiFlex 2 Q
14 • Product description
Plastic powder
yes
Metallic powder
yes
Enamel powder
no
OptiFlex 2 Q
V 08/15
Design and function
General view
1
11
2
14
3
12
8
13
4
10
5
7
15
6
16
OptiFlex 2 Q manual coating equipment - Setup
1 OptiStar CG13 Gun control unit
10 Filter unit
2 OptiSelect GM03 manual powder gun
11 Gun holder
3 OptiFlow injector
12 Hose holder
4 Mobile frame with hand rail
13 Cleaning module
(QuickClean)
5 Fluidizing/suction unit
14 Shelf
6 Vibrating table
15 Rubber wheel
7 Venting hose
16 Swivel wheel
8 Swivel arm with guide sleeve
OptiSelect GM03 manual powder gun
All information about the OptiSelect GM03 manual powder gun can be
found in the documentation for that equipment (enclosed with this
manual)!
OptiStar CG13 Gun control unit
All information about the OptiStar CG13 Control unit will be found in the
corresponding enclosed documentation!
OptiFlow injector
All information about the OptiFlow injector can be found in the
corresponding enclosed documentation!
OptiFlex 2 Q
Product description • 15
V 08/15
Scope of delivery
OptiFlex 2 Q
-
OptiSelect GM03 manual powder gun with gun cable,
powder hose, rinsing air hose and standard nozzle set
(For more on this, see the operating manual for the
OptiSelect GM03 manual powder gun)
-
OptiStar CG13 Control unit in a metal case with power
supply cable
-
plug-in OptiFlow injector
-
mobile trolley with a gun/hose support
-
vibrating base and a fluidizing/suction unit
-
Pneumatic hoses for conveying air (red), supplementary
air (black), fluidizing air (black) and rinsing air (black)
-
Operating manual
-
Short instructions
Typical properties – Characteristics of the functions
Processing the powder directly from the original
powder manufacturer's container
The OptiFlex 2 Q manual coating equipment allows for powder to be
processed directly out of the original powder manufacturer's container. A
titled vibrating floor has been included to ensure that the powder
container empties itself completely.
Freely rotating head piece
The OptiFlex 2 Q manual coating equipment features a freely rotating
and lockable head piece for more ergonomic operation and configuration.
Freely rotating head piece
16 • Product description
OptiFlex 2 Q
V 08/15
Commissioning
Preparation for start-up
Basic conditions
When starting up the OptiFlex 2 Q manual coating unit, the following
general conditions impacting the coating results must be taken into
consideration:
-
Manual coating equipment is set up properly
-
Gun control unit correctly connected
-
Gun correctly connected
-
Corresponding power and compressed air supply available
-
Powder preparation and powder quality
Set-up
The OptiFlex 2 Q manual coating equipment should always be set up
vertically on a flat surface.
WARNING:
The manual coating equipment must not under any circumstances
be set up near a heat source (such as an enameling furnace) or an
electromagnetic source (such as a control cabinet).
OptiFlex 2 Q
Commissioning • 17
V 08/15
Mounting instructions
The OptiFlex 2 Q manual coating equipment must be set up in
accordance with the setup and connecting instructions (included with
delivery).
OptiFlex 2 Q Manual coating equipment
18 • Commissioning
OptiFlex 2 Q
V 08/15
Connection instructions
Gun
Maintenance unit
6 - 10 bar
5,5 bar
Injector
Fluidizing/suction unit
Cleaning module
Connection instructions - overview
The OptiFlex 2 Q manual coating equipment must be connected in
accordance with the setup and connection instructions (Please also
review the operating instructions for the OptiStar CG13 manual gun
control unit).
1.
OptiFlex 2 Q
2.
Commissioning • 19
V 08/15
NOTE:
Use clamp to connect grounding cable to the cabin or the
suspension arrangement. Check ground connections with Ohm
meter and ensure 1 MOhm or less!
3.
4.
5.
6.
7.
8.
9.
10.
NOTE:
The compressed air must be free of oil and water!
20 • Commissioning
OptiFlex 2 Q
V 08/15
Initial start-up
NOTE:
If a malfunction occurs, see the troubleshooting guide, as well as
the gun control unit operating manual!
NOTE:
The remainder of the start-up procedure for the OptiSelect GM03
manual powder gun is explicitly described in the operating
instructions for the OptiStar CG13 manual powder gun control unit
(chapter "Initial start-up" and "Daily start-up")!
OptiFlex 2 Q
Initial start-up • 21
V 08/15
Set head piece
1.
2.
3.
Setting the device type
NOTE:
If the control unit is delivered as a integral component of an
OptiFlex apparatus, then the system parameters will have been
factory preconfigured for optimal use (For more on this, please also
see the operating instructions for the OptiStar CG13 manual gun
control unit)!
NOTE:
The manual gun control unit always starts up to the last configured
settings.
22 • Initial start-up
OptiFlex 2 Q
V 08/15
Operation
Coating
WARNING:
If the manual equipment is not being used for coating in
conjunction with a sufficiently powerful suction unit, then the
stirred-up dust from the coating powder can cause respiratory
issues or cause a slippage/falling hazard.
► The manual equipment may only be operated in conjunction with a
sufficiently powerful suction unit (such as Gema Classic Open booth).
1. Turn on the gun control unit with the ON key
The displays illuminate and the control unit is ready for operation
2. Swivel aside the fluidizing/suction unit
3. Place the open powder container on the vibrating table
WARNING:
If a container is placed on the vibrating plate, then fingers caught in
the gap between the two plates can be crushed.
► The container may weight a max. of 30 kg.
4. Place the fluidizing/suction unit onto the powder
5. Set coating parameters:
6. Press the application button for the appropriate preset mode:
flat parts
complicated parts
overcoat
The arrow above the desired button lights up
OR
7. Press
program key
a) Select desired program (01-20)
b) Change coating parameters as required
OptiFlex 2 Q
Initial start-up • 23
V 08/15
NOTE:
Programs 01-20 are preset at the factory but can be modified at any
time, after which they are automatically stored.
Description
Presetting
Powder output
50%
Total air
4.0 Nm³/h
High voltage
80 kV
Spray current
80 µA
Electrode rinsing air
0.1 Nm³/h
Fluidizing air
0.1 Nm³/h
8. Setting the total air volume
correct powder cloud
too little total air
NOTE:
A total air volume of 4 Nm³/h and a 50% powder share are
recommended as the base values.
9. Adjust the powder output volume (e.g. according to the desired
coating thickness)
or
much powder
24 • Initial start-up
little powder
OptiFlex 2 Q
V 08/15
NOTE:
To achieve maximum efficiency, we recommend avoided an overly
high powder volume where possible!
► The standard setting of 50% and a total air volume of 4 Nm³/h is
recommended at the start. The total air volume is thereby kept
constant automatically by the control unit.
► If values are entered that the equipment cannot implement, then the
operator is informed of this by a blinking in the relevant display and a
temporary error message!
10. Setting the electrode rinsing air
a) Press the key
The second display level will be shown
b)
approx.
0.1 Nm³/h
approx.
0.5 Nm³/h
too much electrode rinsing air
11. Setting the fluidization
a)
Press the key
The second display level will be shown
b)
c) Check the powder fluidization in the powder container.
The powder fluidization in the powder containers depends on
the powder characteristic, the humidity and the ambient air
temperature. Fluidizing and vibration start by switching on
the control unit.
WARNING:
If the fluidization has been incorrectly adjusted, then the coating
powder can create a dust cloud capable of causing respiratory
problems.
► Adjust the fluidization correctly
12. Point the gun into the booth (not at the object to be coated),
press the gun trigger and visually check the powder output
13. Check whether everything is functioning correctly
14. Coating
OptiFlex 2 Q
Initial start-up • 25
V 08/15
15. Adjust the coating parameters as necessary
16. Activate the rinsing function periodically
NOTE:
It prevents the bridging phenomena that can lead to short circuiting
when handling powders such as metallic powders.
In moist or tropical environments, any moisture is driven from the
injector, powder hose and powder gun.
OK
X
CLICK
a)
b) Press the key
for 3 seconds
c)
-
The LCD segments begin to move on the display
WARNING:
The rinsing procedure is started directly.
Procedure
Effect
-
automatic
-
-
1. STOP =
The automatic rinsing process is started
Injector, powder hose, gun and spray nozzle are
purged using compressed air
The automated PowerClean function enables parallel
cleaning of other components, such as the fluid intake
unit, powder container, etc.
The rinsing mode is exited if the automatic rinsing
sequence has finished.
or
After completion of the PowerClean procedure, the controller switches
back to coating mode.
26 • Initial start-up
OptiFlex 2 Q
V 08/15
Setting the background illumination
1. Press
key
The display switches to the following level:
2.
OptiFlex 2 Q
Select the desired brightness
Initial start-up • 27
V 08/15
Color change
General information
When a color change takes place, the automatic cleaning process is
started by activating the remote button on the control
module. All components that contain powder – from the suction tube, to
the injector, powder hose, through to the gun and spray nozzle – are
automatically and comprehensively cleaned with pulses of compressed
air.
The powerful air mover, installed in the frame of the trolley automatically
cleans the suction tube as it is raised. The powder dust that is removed is
extracted to the booth via an exhaust hose..
2.
1.
3. Point the gun into the booth
4. Check, if the exhaust hose is connected to the booth.
5.
6.
7.
8.
OK
X
CLICK
9.
28 • Initial start-up
10.
OptiFlex 2 Q
V 08/15
Press the key
11. 3 seconds
for
12.
13.
14.
15.
16.
17.
OptiFlex 2 Q
Initial start-up • 29
V 08/15
Shutdown
1. Release gun trigger
2. Switch off the control unit
NOTE:
The adjustments for high voltage, powder output, electrode rinsing
air and fluidizing remain stored!
If in disuse for several days
1. Separate from power mains
2. Clean the coating equipment (see the corresponding
operating manual)
3. Turn off the compressed air main supply
30 • Initial start-up
OptiFlex 2 Q
V 08/15
Cleaning and maintenance
NOTE:
Regular and conscientious maintenance increases the service life of
the OptiFlex 2 Q manual coating equipment and provides for a
longer continuous coating quality!
► The parts, which are to be replaced during maintenance work, are
available as spare parts. These parts will be found in the
corresponding spare parts list!
Daily maintenance
1. Clean the injector (see therefore the user manual of the OptiFlow
injector)
2. Clean the powder gun (For more on this, please also review the
user manual for the OptiSelect GM03 manual powder gun)
3. Clean the powder hose; Please also review the section "Color
change"
Weekly maintenance
1. Clean fluidizing/suction unit, injector and powder gun. The
fluidizing/suction unit is placed back into the powder shortly
before restarting operation
2. Check the control unit grounding connections to the coating
booth, the suspension devices of the work pieces, or the
conveyor chain
If in disuse for several days
1. Separate from power mains
2. Clean the coating equipment
3. Turn off the compressed air main supply
Powder hose rinsing
If longer downtimes take place, the powder hose has to be cleaned.
Procedure:
1. Disconnect the powder hose from the hose connection on the
injector
2. Point the gun into the booth
OptiFlex 2 Q
Cleaning and maintenance • 31
V 08/15
3. Blow through the hose manually with a compressed air gun
4. Connect the powder hose again to the hose connection on the
injector
Cleaning
WARNING:
If no dust mask or one of an insufficient filter class is worn when
cleaning the manual equipment, then the dust that is stirred up from
the coating powder can cause respiratory problems.
► The ventilation system must be turned on for all cleaning work.
► A dust mask corresponding to filter class FFP2 at minimum must be
worn during any cleaning work.
Cleaning the fluidizing/suction unit
1. Remove the injector
2. Remove the fluidizing/suction unit
3. Clean the fluidizing/suction unit with compressed air. Also blow
off the suction tube with compressed air
4. Clean the injector (see therefore the injector user manual)
5. Reassemble the individual parts
Cleaning the OptiSelect GM03 manual powder
gun
Frequent cleaning of the gun helps to guarantee the coating quality.
NOTE:
Before cleaning the powder gun, switch off the control unit. The
compressed air used for cleaning must be free of oil and water!
Daily:
1. Blow off the outside of the gun and wipe, clean etc.
Weekly:
2. Remove the powder hose from the connection
3. Remove the spray nozzle from the gun and clean it
4. Blow out the gun from the connection in flow direction with
compressed air
5. Clean the integrated gun tube with the provided gun brush
6. Blow through the gun with compressed air again
7. Clean the powder hose
8. Reassemble the gun and connect it
NOTE:
Please also review the user manual for the OptiSelect GM03 manual
powder gun!
32 • Cleaning and maintenance
OptiFlex 2 Q
V 08/15
Maintenance and cleaning of the filter unit
The filter unit on the OptiFlex 2 Q manual coating equipment measures
and cleans the compressed air. This is where the equipment's main
compressed air connection is located.
Replacing the filter element
Procedure:
1. Unscrew the filter glass on the filter unit
2. Remove the complete filter element
3. Replace the filter element
4. Clean the filter glass on the inside and install it again
OptiFlex 2 Q
Cleaning and maintenance • 33
V 08/15
Fault remedying
General information
NOTE:
Prior to any troubleshooting measures, always check whether the
equipment parameters (P00) as configured in the control unit are
correct (See operating instructions for the OptiStar CG13 manual
gun control unit, Chapter "Initial Start-up – Setting Equipment
Type")
Fault
Causes
Fault remedying
Control unit displays
remain dark, although
the control unit is
switched on
Control unit is not
connected to the mains
Connect the equipment
with the mains cable
Power pack fuse
defective
Replace the fuse
Power pack defective
Contact local Gema
representative
Compressed air not
present
Connect the equipment
to the compressed air
Injector, throttle motor or
nozzle on injector,
powder hose or powder
gun are clogged
Clean the corresponding
part
Insert sleeve in the
injector is clogged
Replace
Insert sleeve is not
installed
Mount insert sleeve
Fluidization not running
see below
Total air incorrectly
configured
Set total air correctly
(Default value 4 Nm³/h)
Main valve defective
Replace main valve
Gun not connected
Connect the gun
Gun plug, gun cable or
gun cable connection
defective
Contact local Gema
representative
Remote control on
powder gun defective
Contact local Gema
representative
The gun does not
spray powder,
although the control
unit is switched on and
the gun trigger is
pressed
Gun LED remains
dark, although the gun
is triggered
OptiFlex 2 Q
Fault remedying • 35
V 08/15
Fault
Causes
Fault remedying
Powder does not
adhere to object,
although the gun is
triggered and sprays
powder
The objects are
improperly or
insufficiently grounded
Check grounding,
reground at better
quality
High voltage and current
deactivated
Press the selection key
(application key)
High voltage cascade
defective
Contact local Gema
representative
Compressed air not
present
Connect the equipment
to the compressed air
Fluidizing air is set too
low on the control unit
Set the fluidizing air
correctly
Throttle motor defective
Contact local Gema
representative
No electrode rinsing air
Rinsing air throttle motor
defective
Contact local Gema
representative
Vibrator not functioning
Vibrator/condenser
broken
Contact local Gema
representative
Vibrator not plugged in
plug in
Incorrect equipment
type configured
Configure parameter
P00 (See operating
instructions for the
OptiStar CG13 manual
gun control unit,
Chapter "Initial Start-up
– Setting Equipment
Type")
The powder is not
fluidized
36 • Fault remedying
OptiFlex 2 Q
V 08/15
Spare parts list
Ordering spare parts
When ordering spare parts for powder coating equipment, please indicate
the following specifications:
-
Type and serial number of your powder coating
equipment
-
Order number, quantity and description of each spare
part
-
Type OptiFlex 2 Q
Serial number 1234 5678
-
Order no. 203 386, 1 piece, Clamp - Ø 18/15 mm
Example:
When ordering cable or hose material, the required length must also be
given. The spare part numbers of this bulk stock is always marked with
an *.
Wearing parts are always marked with a #.
All dimensions of plastic hoses are specified with the external and
internal diameter:
Example:
Ø 8/6 mm, 8 mm outside diameter (o/d) / 6 mm inside diameter (i/d)
WARNING!
Only original Gema spare parts should be used, because the
explosion protection will also be preserved that way. The use of
spare parts from other manufacturers will invalidate the Gema
guarantee conditions!
OptiFlex 2 Q
Spare parts list • 37
V 08/15
OptiFlex 2 Q - Spare parts list
1
CG13 gun control unit – complete (see corresponding operating manual)
1009 971
2
GM03 manual powder gun – complete (see corresponding user manual)
1008 070
3
IG06 injector – complete (see corresponding user manual)
1007 780
4
Pneumatic connection for conveying air – complete (incl. Pos. 4.1, 4.2, 4.3)
4.1
Quick release connection – NW5, Ø 8 mm, red
261 645
4.2
Nut with kink protection – M12x1 mm, Ø 8 mm
201 316
4.3
Plastic tube – Ø 8/6 mm, red
5
103 500*
Pneumatic connection for supplementary air - complete (incl. Pos. 5.1, 5.2 and 5.3)
5.1
Quick release connection - NW5, Ø 8 mm, black
261 637
5.2
Nut with kink protection – M12x1 mm, Ø 8 mm
201 316
5.3
Plastic tube - Ø 8/6 mm, black
6
Cleaning module – complete, left
7
Pneumatic connection for QuickClean air - complete (incl. Pos. 7.1 and 7.2)
1008 038*
1009 653
7.1
Quick release connection - NW5, Ø 8 mm
1008 027
7.2
Plastic tube - Ø 8/6 mm, black
103 152*
Fluidizing/suction unit - complete (incl. pos. 8.1)
1009 679
Gasket NBR45
1010 101
8
8.1
9
Pneumatic connection for conveying air - complete (incl. Pos. 9.1, 9.2 and 9.3)
9.1
Quick release connection - NW5, Ø 6 mm
200 840
9.2
Nut with kink protection – M10x1 mm, Ø 6 mm
201 308
9.3
Plastic tube - Ø 6/4 mm, black
10
Pneumatic group – complete (see corresponding spare parts list)
11
Quick release connection - NW7.8-Ø 10- Ø 26 mm
239 267
12
Rubber damper - Ø 20x25 mm, M6/2a, 43sh
246 000
13
Hexagon shakeproof nut - M6
244 430
14
Powder hose – Ø 15/10 mm, 6 m
1001 673
15
Kink protection
1008 844
17
Spiral hose – ID 20 mm, 5 m
1009 650
18
Hose clamp - Ø 17-25 mm
19
Screw – M5x20 mm
1004 167
20
Connector
1010 062
21
AirMover
1009 649
22
Short instructions
1007 143
23
Operating manual
1010 267
1001 973
223 085
* Please indicate length
38 • Spare parts list
OptiFlex 2 Q
V 08/15
OptiFlex 2 Q - Spare parts list
22
23
1
9
2
4
5
15
17
3
10
8.1
18
19
21
7
20
6
11
8
14
12, 13
OptiFlex 2 Q manual coating equipment – Spare parts
OptiFlex 2 Q
Spare parts list • 39
V 08/15
OptiFlex 2 Q Dual Gun - Spare parts list
6
6.1
7
Cleaning module – complete, left
1009 653
Cleaning module – complete, right
1009 654
Pneumatic connection for QuickClean air - complete (incl. Pos. 7.1 and 7.2)
7.1
Quick release connection - NW5, Ø 8 mm
1008 027
7.2
Plastic tube - Ø 8/6 mm, black
103 152*
Fluidizing/suction unit - complete
1009 679
8
Pneumatic group – complete (see corresponding spare parts list)
* Please indicate length
6
7
6.1
8
40 • Spare parts list
OptiFlex 2 Q
V 08/15
OptiFlex 2 Q – Pneumatic group
Pneumatic group - complete
1
Filter cartridge - 20 µm
2
Plug – Ø 8 mm
1008 235
1008 239#
238 023
# Wearing part
2
1
OptiFlex 2 Q – Pneumatic group
OptiFlex 2 Q
Spare parts list • 41
V 08/15
OptiFlex 2 Q Dual Gun - Pneumatic group
1
Filter cartridge - 20 µm
1008 239#
# Wearing part
1
OptiFlex 2 Q Dual Gun - Pneumatic group
42 • Spare parts list
OptiFlex 2 Q
V 08/15
OptiFlex 2 Q
Spare parts list • 43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement