Vermont Castings LHERDV30 Operating instructions

Vermont Castings LHERDV30 Operating instructions
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE
WARNING!
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
E X A C T LY, A F I R E O R
EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS
OF LIFE.
FOR YOUR SAFETY
Installation and service must
be performed by a qualified
installer, service agency or the
gas supplier.
Direct Vent Insert
Models:LHERDV20
LHERDV30
LHECDV20
LHECDV30
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electric switch;
do not use any phone in your
building.
• Immediately call your gas supplier
from your neighbor’s phone. Follow
the gas suppliers instructions.
• If you cannot reach your gas
supplier call the fire department.
DO N���
OT STORE
������ OR
��� USE
����
GASOLINE OR OTHER
FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE.
Homeowner's Installation and
Operating Manual
DE S I GN
CERTIFIED
CE
RTIFI E D
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
10004894 1/13 Rev. 8
LHEDV Series Direct Vent Insert
Table of Contents
Please read the Installation & Operating Instructions before using this appliance.
Thank you and congratulations on your purchase of an Vermont Castings Group fireplace insert.
IMPORTANT - Read all instructions and warnings carefully before starting installation. Failure to follow these
instructions may result in a possible fire hazard and will void the manufacturers' warranty.
Installation Instruction
General Information, Warnings, Cautions............................................................................................3
Insert Applications...............................................................................................................................3
Requirements for the Commonwealth of Massachusetts....................................................................4
Fireplace & Trim Dimensions . ............................................................................................................5
Locating Your Fireplace Insert.............................................................................................................6
Mantels................................................................................................................................................6
Framing & Finishing.............................................................................................................................6
Zero Clearance Applications................................................................................................................7
Gas Specifications...............................................................................................................................7
Gas Inlet & Manifold Pressures...........................................................................................................7
High Elevations....................................................................................................................................7
Preparation..........................................................................................................................................7
Gas Line Installation............................................................................................................................7
Gas Supply Pressures.........................................................................................................................8
Fan Kit.................................................................................................................................................8
Fan Removal Instructions....................................................................................................................8
Installation of Trim Switch for RN/RP Gas Valves...............................................................................9
Venting and Installation.......................................................................................................................9
Liner Installation................................................................................................................................10
Round Vent Termination Installation..................................................................................................12
Ceramic Refractory Installation.........................................................................................................12
Venting Components.........................................................................................................................13
Operating Instructions
General Glass Information................................................................................................................ 14
Louvre Removal................................................................................................................................14
Glass Cleaning..................................................................................................................................14
Glass Frame Removal.......................................................................................................................14
Log & Burner Lava Rock Installation.................................................................................................14
Large Lava Rock Placement.............................................................................................................15
Flame Adjustment .............................................................................................................................15
Flame Characteristics........................................................................................................................16
First Firing..........................................................................................................................................16
Lighting & Operating Instructions .....................................................................................................17
Troubleshooting Gas Control (820 Millivolt Gas Valve).....................................................................18
Troubleshooting Gas Control (Honeywell)........................................................................................19
Instructions for RF Comfort Control Valve.........................................................................................20
Maintenance
Cleaning the Standing Pilot Control System......................................................................................24
Trim Cleaning....................................................................................................................................24
Replacement Parts ...............................................................................................................................................25
Optional Accessories
Remote Controls................................................................................................................................28
Zero Clearance Kit.............................................................................................................................28
Trim Options......................................................................................................................................28
Warranty . ..............................................................................................................................................................31
Energuide...............................................................................................................................................................32
10004894
LHEDV Series Direct Vent Insert
Installation & Operating Instructions
This gas appliance should be installed by a qualified installer in
accordance with local building codes and with current CSA-B149.1
Installation codes for Gas Burning Appliances and Equipment. ����
FOR
U.S. Installations follow local codes and/or the current National
Fuel Gas Code ANSI Z223.1/NFPA 54.
In the Commonwealth of Massachusetts, all gas fittings and installation of this heater shall only be done by a licensed gas fitter
or licensed plumber.
FOR SAFE INSTALLATION AND OPERATION OF YOUR
GAS FIREPLACE PLEASE NOTE THE FOLLOWING:
1.This appliance gives off high temperatures and should be
located out of high traffic areas and away from furniture and
draperies.
2. Children and adults should be alerted to the hazards of the
high surface temperatures of this appliance and should stay
away to avoid burns or ignition of clothing.
3. Attention : En raison de la température élevée de la
surface vitrée, les enfants doivent être supervisés en tout
temps quand ils sont dans la pièce où se trouve le foyer.
7!2.).'
(/4',!337),,
#!53%"52.3
$/./44/5#(',!33
5.4),#//,%$
.%6%2!,,/7#(),$2%.
4/4/5#(',!33
4. Under no circumstances should this appliance be modified.
Parts removed for servicing should be replaced prior to operating this appliance again.
5. Installation and any repairs to this appliance should be carried
out by a qualified service person. A professional service person
should be contacted to inspect this appliance annually. Make it
a practice to have all of your gas appliances checked annually.
More frequent cleaning may be required due to excess lint and
dust from carpeting, bedding material, etc.
6. Control compartments, burners and air passages in this appliance should be kept clean and free of dust and lint. Make
sure that the gas valve and pilot light are turned off before you
attempt to clean this unit.
7.The venting system (chimney) of this appliance should be
checked at least once a year and if needed your venting system
should be cleaned.
8. Keep the area around your appliance clear of combustible
materials, gasoline and other flammable vapor and liquids.
This appliance should not be used as a drying rack for clothing,
nor should Christmas stockings or decorations be hung in the
area of it.
9.Under no circumstances should any solid fuels (wood, coal,
paper or cardboard etc.) be used in this appliance.
10.Whether the zero clearance kit is installed directly on carpeting, vinyl tile or any combustible material other than wood, this
heater must be installed on a metal or wood panel extending
the full width and depth of the heater. The insert can not be
installed directly onto or into combustibles.
10004894
WARNING: Check with your electronics manufacturer
before installing a television or other electronic device
above this fireplace.
LHECDV20 / LHERDV20
LHEDV30 / LHERDV30
Certified To
ANSI Z 21.88b-2008 / CSA 2.33b-2008
Vented Gas Fireplace Heaters
IMPORTANT:
Please Read The Following Carefully
It is normal for fireplaces fabricated of steel to give off some
expansion and/or contraction noises during the start up or
cool down cycle. Similar noises are found with your furnace
heat exchanger or car engine.
It is not unusual for your gas fireplace to give off some odor
the first time it is burned. This is due to the curing of the paint
and any undetected oil from the manufacturing process.
Please ensure that your room is well ventilated - open
all windows.
It is recommended that you burn your fireplace for at least ten
(10) hours the first time you use it. If optional fan kit has been
installed, place fan in the "OFF" position during this time.
This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not
prohibited by local codes.
This appliance is only for use with the type of gas indicated
on the rating plate.
Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State
of California to cause cancer, birth defects and other
reproductive harm.
California Health & Safety Code Sec. 25249.6
Insert Applications
Before installing the gas fireplace insert, consideration must
be given to the functioning needs of the fireplace. The size
of the fireplace cavity (min. 25¹⁄₄"W x 17¹⁄x"H x 13¹⁄₂" D (641 x
438 x 343 mm) for the LHECDV20 and LHERDV20, 28³⁄₄"W
x 21"H x 15¹⁄₂"D (730 x 533 x 394 mm) for LHECDV30 and
LHERDV30), the design of the chimney for effective venting
should be determined. The availability of the gas supply as
well as electricity for the insert fan must be confirmed.
Your Direct Vent Insert unit is designed to be
vented vertically with a minimum height of
12' (4 m).
LHEDV Series Direct Vent Insert
Installation & Operating Instructions
Requirements for the Commonwealth of
Massachusetts
All gas fitting and installation of this heater shall only be
done by a licensed gas fitter or licensed plumber.
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in whole
or in part for residential purposes, including those owned
or operated by the Commonwealth and where the side wall
exhaust vent termination is less than seven (7) feet above
finished grade in the area of the venting, including but not
limited to decks and porches, the following requirements
shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm is installed on each additional level of the
dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled
equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery
back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can not
be met at the time of completion of installation, the owner
shall have a period of thirty (30) days to comply with the
above requirements; provided, however, that during said
thirty (30) day period, a battery operated carbon monoxide
detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance
with the above provisions shall comply with NFPA 720 and
ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently
mounted to the exterior of the building at a minimum height
of eight (8) feet above grade directly in line with the exhaust
vent terminal for the horizontally vented gas fueled heating
appliance or equipment. The sign shall read, in print size no
less than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW, KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally
vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes
carbon monoxide detectors and signage installed in
accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
•
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
Product Approved side wall horizontally vented gas fueled
equipment installed in a room or structure separate from
the dwelling, building or structure used in whole or in
part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components;
and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide
the parts for venting the flue gases, but identifies “special
venting systems”, the following requirements shall be
satisfied by the manufacturer:
• The referenced “special venting system” instructions shall
be included with the appliance or equipment installation
instructions; and
• The “special venting systems” shall be Product
Approved by the Board, and the instructions for that
system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved
side wall horizontally vented gas fueled equipment, all
venting instructions, all parts lists for venting instructions,
and/or all venting design instructions shall remain with
the appliance or equipment at the completion of the
installation.
10004894
LHEDV Series Direct Vent Insert
Fireplace & Trim Dimensions
3" (75mm)
Dia.
B
D
A
L
G
A
B
C
K
M
P
U
V
J
Zero Clearance Kit
Insulation
Q
H
I
T
4894
LHEDV SPEC
4/03
S
E
F
O
R
Minimum Fireplace
Insert Opening
N
1"
Air Circulating Channel
Gas Inlet Knockout
1 = LHESSB
Q
Fireplace
opening
height
U - Firebox depth at insert back height (V)
2 = LHESLB/LHEABSL/LHESLGA
V - Insert back height
3 = LHECSLB/LHECSLMB/LHECSLSA R - Fireplace opening width
S - Depth of insert
NOTE: LHESLGA is only available for
4 = LHEACNSS FP1248
T - Firebox width at insert depth(S) Model LHEC30 and LHER30
5 = LHETCK
Minimum fireplace
T
R
I
M
F
I
R
E
P
L
A
C
E
M O
I P
N E
I N
M I
U N
M
G
10004894
opening
LHECDV20
1/03
LHERDV20
LHECDV30
HEZC
A-1
20⁷⁄₈" (530 mm)20⁷⁄₈" (530 mm)26³⁄₄"
specs
B-1
30³⁄₄" (781 mm)
30³⁄₄" (781 mm)
38¹⁄₄"
1/03
A-224¹⁄₄" (616 mm)24¹⁄₄" (616 mm)28³⁄₁₆"
B-2
37¹⁄₂" (952 mm)
37¹⁄₂" (952 mm)
41"
A-324¹⁄₄" (616 mm)24¹⁄₄" (616 mm)28¹⁄₄"
B-3
38¹⁄₈" (968 mm)
38¹⁄₈" (968 mm)
41¹¹⁄₁₆"
A-420³⁄₄" (527 mm)20³⁄₄" (527 mm)24³⁄₄"
B-4
30⁷⁄₈" (784 mm)
30⁷⁄₈" (784 mm)
34⁷⁄₁₆"
A-528"
(711 mm)28"
(711 mm)
32¹⁄₄"
B-5
45"
(1143 mm)
45"
(1143 mm)
49"
C25⁵⁄₈" (651 mm)25⁵⁄₈" (651 mm)29³⁄₁₆"
D
17"
(432 mm)
17"
(432 mm)
17B⁄₈"
E
35"
(889 mm)
35"
(889 mm)
35"
F26⁵⁄₈" (676 mm)26⁵⁄₈" (676 mm)26⁵⁄₈"
G
13¹⁄₂" (343 mm)
13¹⁄₂"
(343mm)
15¹⁄₂"
H
17"
(432 mm)
17"
(432 mm)20¹⁄₂"
I
18"
(457 mm)
18"
(457 mm)21¹⁄₂"
J
19¹⁄₈" (486 mm)
19Z⁄₈" (486 mm)22B\,"
K
15"
(381 mm)
15"
(381 mm)
17"
L
10C\,"
(264mm)
10C\V" (273 mm)
11³⁄₄"
M
8¹⁄₂"
(216 mm)
8¹⁄₂"
(216 mm)
8¹⁄₂"
N
37¹⁄₄"
(946mm)
37¹⁄₄" (946 mm)
37¹⁄₄"
O
19¹⁄₈" (486 mm)
19¹⁄₈" (486 mm)
19¹⁄₈"
P27¹⁄₄" (692 mm)27¹⁄₄" (692 mm)27¹⁄₄"
Q
17¹⁄X" (444 mm)
17¹⁄X" (444 mm)21"
R25¹⁄₄" (641 mm)25¹⁄₄" (641 mm)28³⁄₄"
S
13¹⁄₂" (343 mm)
13¹⁄₂" (343 mm)
15¹⁄₂"
T
17"
(432 mm)
17"
(432 mm)
17³⁄₄"
U
13³⁄₄" (349 mm)
13C\v" (349 mm)
15C\v"
V
18"
(457mm)
18"
(457 mm)21⁵⁄₁₆"
LHERDV30
(680 mm)26³⁄₄"
(972 mm)
38¹⁄₄"
(716 mm)28³⁄₁₆"
(1042 mm)
41"
(717 mm)28¹⁄₄"
(1059 mm)
41¹¹⁄₁₆"
(629 mm24³⁄₄"
(875 mm)
34⁷⁄₁₆"
(819 mm)
32¹⁄₄"
(1245 mm)
49"
(741 mm)29³⁄₁₆"
(448 mm)
16C⁄₄"
(889 mm)
35"
(676 mm)26⁵⁄₈"
(394 mm)
16¹⁄₂"
(521 mm)20¹⁄₂"
(546 mm)21¹⁄₂"
(575 mm)22B\,"
(432 mm)
18"
(298 mm)
12³⁄₄"
(216 mm)
8¹⁄₂"
(946 mm)
37¹⁄₄"
(486 mm)
19¹⁄₈"
(692 mm)27¹⁄₄"
(533 mm)21"
(730 mm)28³⁄₄"
(394 mm)
16¹⁄₂"
(451 mm)
17³⁄₄"
(400 mm)
16¹⁄₂"
(541 mm)21⁵⁄₁₆"
(680 mm)
(972 mm)
(716 mm)
(1042 mm)
(717 mm)
(1059 mm)
(629 mm)
(875 mm)
(819 mm)
(1245 mm)
(741 mm)
(425 mm)
(889 mm)
(676 mm)
(419 mm)
(521 mm)
(546 mm)
(575 mm)
(457 mm)
(324 mm)
(216 mm)
(946 mm)
(486 mm)
(692 mm)
(533 mm)
(730 mm)
(419 mm)
(451 mm)
(419 mm)
(541 mm)
LHEDV Series Direct Vent Insert
Locating Your Gas Fireplace Insert
with Zero Clearance Kit
X
A
E
B
X
For Zero Clearance Kit applications, it is important to
determine the finished facing material before beginning
to frame. This will allow for the thickness of the finishing
material between the frame and the fireplace trim.
Similarly, consideration must be given to the 1" inch depth
of the air inlet channel sitting on the fireplace base. Finishing material for the hearth should be flush with the top of
the air inlet channel.
C
X
Framing & Finishing
D
If the fireplace is installed at floor level a noncombustible
hearth must extend a minimum 12" (305 mm) in front of
the fireplace.
F
FP1249a
Fig. 1 Locating unit with zero clearance kit.
A) Flat on wall C) Island
E) *Flat on wall corner
B) Cross corner
D) *Room divider
FP1249a
F) Chase installation
locating DV unit
If the fireplace is recessed into the wall and at least 12"
(305 mm) above floor level, no hearth is required.
The use of wallpaper adjacent to this fireplace
is not recommended as high temperatures
given off by this fireplace may adversely
effect the binders in the adhesive used to
apply the wallpaper.
with zero clearance kit
NOTE: (Fig. 1)
4/03
* When you install your fireplace in (D) Room divider or (E) Flat
on wall corner positions, a minimum of 6 (X) inches (153 mm)
clearance must be maintained from the perpendicular wall and
the outer edge of the trim.
NOTE: Insulating around the fireplace will result in overheating and possible malfunctioning of the circulating fan.
Mantels
When the unit is installed into a woodburning fireplace,
the minimum distance the mantel can be placed above the
fireplace is governed by local building codes applicable to
woodburning fireplaces. Consult local authorities having
jurisdiction for these clearances.
For applications requiring the use of a Zero Clearance Kit,
the minimum height a mantel can be installed above the
fireplace is 24" (610 mm) from the top of the upper louvres.
The maximum mantel depth is 8" (203 mm). (Fig. 2)
37¹⁄₄" (946mm)
35"
(889mm)
The underside of the mantel will become warm.
Use only finishes which are heat resistant and
do not discolor.
Air Inlet Channel
HEDVCAK is
installed outside
ofthe flue pipe
only.
27¹⁄₄" (692mm)
24" Min.
(610mm)
Drywall
19¹⁄₈"
(486mm)
Decorative Trim Kit
Finish Wall
FP1351
Fig. 3 LHEDV insert framing dimensions.
FP1325
FP1251
Insert framing
and finishing
1/03
Fig. 2 Minimum mantel height above fireplace.
10004894
FP1325
Insert mantel
LHEDV Series Direct Vent Insert
Zero Clearance Applications
An alternate air supply is recommended with
this component.
For installation other than in existing woodburning fireplaces
such as new construction or renovation projects, a Zero
Clearance Kit must be used. The kit enables these inserts
to be installed in combustible environments. Whenever
using a Zero Clearance Kit, consideration must be given to
the dimensions of the Zero Clearance Kit and the requirements of the Air Kit.
NOTE: If a Zero Clearance Kit is required for models
LHECDV20/LHERDV20/LHECDV30/LHERDV30 Direct
Vent Inserts, only the Vermont Castings Group zero
clearance kit HEZC combined with the HEDVCAK is
approved to be used. Refer to Page 9, figure 10 for HEDVCAK chimney adapter kit installation. When using the
HEZC with insert models LHECDV20 or LHERDV20, the
Trim Closure Kit, LHE20TCK, must also be installed.
Gas Specifications
Max. Min.
Gas Input Input
Model
Fuel Control Btu/h Btu/h
LHECDV20RN Natural Millivolt 20,000 14,000
Hi/Lo
LHECDV20RP Propane Millivolt20,000 15,000
Hi/Lo
LHECDV20RFN Natural Comfort 20,000 14,000
Control
LHECDV20RFPPropane Comfort20,000 15,000
Control
LHERDV20RN Natural Millivolt20,000 14,000
Hi/Lo
LHERDV20RP Propane Millivolt20,000 15,000
Hi/Lo
LHECDV30RN Natural Millivolt 30,00021,000
Hi/Lo
LHECDV30RP Propane Millivolt 30,00022,500
Hi/Lo
LHECDV30RFN Natural Comfort 30,00021,000
Control
LHECDV30RFPPropane Comfort 30,00022,500
Control
LHERDV30RN Natural Millivolt 30,00021,000
Hi/Lo
LHERDV30RP Propane Millivolt 30,00022,500
Hi/Lo
Air Shutter
Setting
Front Rear
Fully Closed
Open 50%
Fully Closed
Open 80%
Fully Closed
Open 50%
Fully Closed
Open 80%
Fully Closed
Open 50%
Fully Closed
Open 80%
Fully Fully
Open Open
Fully Fully
Open Open
Fully Fully
Open Open
Fully Fully
Open Open
Fully Fully
Open Open
Fully Fully
Open Open
Gas Inlet & Manifold Pressures
Minimum Inlet Pressure
Maximum Inlet Pressure
Manifold Pressure
10004894
Natural
5.5" w.c.
14.0" w.c.
3.5" w.c.
LP
11.0" w.c.
14.0" w.c.
10.0" w.c.
Do not use this appliance if any part of it has
been under water. Immediately call a qualified service technician to inspect the unit and
replace any part of the control which has been
under water.
These gas inserts are approved for installation in
solid fuel burning masonry or zero clearance fireplaces.
High Elevations
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to 4,500
feet (1,370m) above sea level.
For elevations above 4,500 feet (1,370m) in USA,
installations must be in accordance with the current ANSI Z223.1/NFPA 54 and/or local codes having
jurisdiction.
In Canada, please consult provincial and/or local
authorities having jurisdiction for installations at
elevations above 4,500 feet (1,370m).
Preparation
Before beginning, remove glass door and logs from unit.
Also check to make sure there is no hidden damage to
the unit. Take a minute and plan out the gas,venting and
electrical route. It is best to start with the gas line first followed by the chimney liner. (Refer to Page 9)
Gas Line Installation
When purging the gas line, the front glass
must be removed.
If gas piping from the source to the heater location
has not been accomplished, install the required pipe. Consult
local plumbing code to assure proper pipe size.
The gas pipeline can be brought in through the rear or the
base of the heater.
NOTE: The gas line connection can be made of either
properly tinned 3/8" copper tubing, 1/2" rigid pipe or an
approved flex connector then reduced to 3/8" to the heater.
Some municipalities have additional local codes, it is always
best to consult your local authority and the CSA- B149.1
installation code.
U.S. Installations consult the current National Fuel Gas
Code, ANSI Z223.1/NFPA 54.
Always check for gas leaks with a mild soap
and water solution. Do not use an open flame
for leak testing.
LHEDV Series Direct Vent Insert
The appliance, when installed must be electrically connected and grounded in accordance
with local codes or, in the absence of local
codes, with the current CSA C22.1 Canadian
Electrical Code.
The gas control is equipped with a captured screw type
pressure test point, therefore it is not necessary to provide
a 1/8" test point up stream of the control.
When using copper or flex connector, use only approved
fittings. Always provide a union when using black iron
pipe so the gas line can be easily disconnected for burner
or fan servicing. See gas specifications for pressure details
and ratings. NOTE: If flex connector is used, it must be
kept inside of the heater.
U.S. Installations, follow local codes and the
National Electrical Code, ansi/nfpa no. 70.
Should this fan require servicing, the power
supply must be disconnected. For rewiring
of any replacement components refer to
Figure 6.
1/2" Gas Supply
1/2" x 3/8" Shut Off Valve
3/8" Nipple
3/8" Union
Screw
Stud
3/8" Nipple
Thermal Sensor is
Attached to Burner
Base
FP297
Screw Stud
Fig. 4 Typical gas supply installation.
Gas Supply Pressures
FP297
This heater must be isolated
from the gas supply piping
INSTA VENT FREE
system by closing its individual
manual shut-off valve during
R MODEL GAS SUPPLY
any pressure equal to or 8/24/96
less than 1/2 psig (3.45kPa).
The heater and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.45kPa).
Fan Kit
115 volt, 60 Hz. 56w (Model FK24)
NOTE: The LHERDV20 and LHERDV30 are not designed
for a fan kit.
The fan kit includes the following: fan, temperature sensor,
speed control and a 6 ft. cord. The following explains how
to start and set the fan for automatic operation.
1. Plug in the electrical cord.
2.Start gas fire - see lighting procedures.
3.Turn on fan speed control.
4. Wait until the unit has warmed up sufficiently to activate
the temperature sensor, approx. 5-10 minutes.
5. Once fan starts, adjust speed control to desired fan
speed. The fan will now automatically come on every
time the fireplace is in operation. Should the fan not be
needed simply turn off the speed control.
Fan is Installed at
the Back of the Air
Intake Box
Fan Speed Control/Junction Box
FP1252
Fig. 5 Fan location.
Fan
Temperature Sensor
Speed
Control
Black
White
Ground
FP1252
FK24 install
1/03
FP394
Fig. 6 Wiring diagram RN/RP. NOTE: For comfort valve wiring
diagram refer to Page 18,FP394
Figure 27.
WIRING DIAGRAM
11/20/96
Fan Removal
Instructions
1.Turn off gas and electricity.
2. Remove the front glass.
3. Remove the logs.
CAUTION: Logs may be hot!
4. For Model LHECDV20: remove burner assembly and
bracket rear log. For Model LHECDV30: remove bracket
rear log and cover fan.
5. Remove the fan mounting nuts (2 nuts). (Fig. 5)
6.Slip off the electrical connector at the motor.
7. Lift out the fan.
8.To reinstall reverse procedure.
10004894
LHEDV Series Direct Vent Insert
Honeywell Valve
Right Side Installation
Left Side Installation
On/Off
Switch Assembly
On/Off
Switch Assembly
Wiring from
Millivolt Gas
Valve
FP1330
Fig. 7 Insert ON/OFF switch with wiring assembly into
bracket switch.
FP1330
Switch assy
4/03
FP1331
Fig. 8 For left side installation, reverse switch position in
bracket.
SIT Valve
THTP
Thermopile
FP1218
Fig. 9b On/Off switch wiring.
CAUTION: Do not wire millivolt remote wall
switch for gas fireplace to a 120v power
supply.
Venting
Installation
FP1218
1.The fireplace Remote
may be installed
in and vented through
switch
any solid fuel fireplace that has a minimum fireplace
wiring
opening 25¹⁄₄"W
x 17¹⁄₂" H x 13¹⁄₂"D (641 x 438 x 343
mm) for LHECDV20
8/02and LHERDV20 or 28³⁄₄"W x 21"H
x 15¹⁄₂"D (730 x 533 x 394 mm) for LHECDV30 and
LHERDV30 and has been installed in accordance with
the National, Provincial/State and local building codes
and is constructed of noncombustible materials.
2. Only HEDVRT RD vent termination kit, HEDVT (8 x
12) or HEDVT (12 x 12) termination kit and flex vent kit
HEDVK25 or HEDVK35 are to be use din this installation.
Under no circumstances should B vent or C vent be
used on this application.
3. Any flue damper must be removed or blocked open.
5.The chimney must be clean and in good working order
and constructed of noncombustible materials.
6. Make sure that all chimney cleanouts fit properly so air
cannot leak into the chimney.
7. Install the appliance without trim frame and make all
gas fittings and electrical connections.
8. Install the decorative trim frame. Please refer to the
Frame Assembly instructions.
Installer must attach red warning plate with
screws supplied with the gas fireplace insert
to the inside of the firebox of the fireplace into
which the gas fireplace insert is installed.
TP
Cutting any sheet metal parts of the fireplace,
in which the gas fireplace insert is to be installed, is prohibited.
TH
FP1331
on/off switch
4/03
OT
PIL
FP382a
Fig. 9a On/Off switch or millivolt thermostat.
10004894
TPTH
1.Thread wire through openings on the right side of fireplace. Do not cut wire or insulation on metal edges.
2. Insert ON/OFF switch with wiring assembly into the
bracket switch with the pre-punched opening mounted
on the right side of the trim. (Fig. 7)
3. For left side installation, relocate the bracket switch to
the left side of the trim kit and repeat Step 2. (Fig. 8)
4. Connect wiring from the switch to the gas valve (Fig.
9a & b).
TP
TH
Installation of Trim Switch
for RN/RP Gas Valves
FP382a
REMOTE SWITCH WIRING - NVC
1/03
If the factory-built fireplace has no gas access hole(s) provided, an access hole of
1¹⁄₂" (38 mm) or less may be drilled through
the lower sides or bottom of the firebox in a
proper workmanship-like manner. This access
hole must be plugged with a noncombustible
insulation after the gas supply line has been
installed.
LHEDV Series Direct Vent Insert
WARNING
Some factory-built fireplaces have air passages
on face of fireplace for zero clearance capabilities.
Under no circumstances should these passages be
blocked.
Liner Installation
The collar extending down from the termination base is
the air intake connector. Be sure the flex vent, which is
connected to this collar, is also connected to the labelled
air intake flue collar on the fireplace. Make sure the flex
vent is attached on the correct collar and cap for exhaust
as well.
Slide the insulation provided in the termination kit over the
two (2) 3" flex liners, (to be attached to the 3" flue collar
and cap of the termination). Feed one 3" flex vent from
the bottom of the termination up through the 4" sleeve.
Apply hi-temp sealant on the rain cap collar and slide the
flex vent over the end of the rain cap collar fastening with
the clamp provided. Slide the flex liner back down the 4"
sleeve until 4" cap slides over the sleeve. Attach cap to
the sleeve with four (4) screws supplied. Apply hi-temp
sealant over the air intake collar and attach intake flex
vent in the same method. Feed the two flex liners down
the chimney through the damper opening. Tighten termination to the chimney using the screws provided. (Fig. 10)
NOTE: For Round Vent Terminations - tighten termination to the chimney by pushing the four (4) straps of the
vent termination against the chimney and secure with four
(4) screws provided. (Fig. 12)
Flue gas exits
through the vent
termination rain
cap
1) Attach flexible pipe
to rain cap
2) Secure with clamp
3) Attach raincap to
vent termiantion using
three screws
Outside combustion
air enters through the
lower level of the vent
termination
Pull flexible pipe
through vent
termination
Secure with
clamp and
three screws
NOTE:
Minimum Vent Height
- 12 feet
Maximum Vent Height
- 35 feet
Air Intake
Exhaust
Air intake collar with
label secured with
clamp and three
screws
Exhaust collar secured
with clamp and three
screws
In case the fireplace opening is only minimum height 21"
(533 mm) and access from the front is not possible, follow
the instructions below.
1. Remove flue collar plate assembly. Unbolt the top fastener plate and move it to the back first before sliding
the flue collar plate out from the top of the unit. (Fig.
13)
2. Apply a bead of hi-temp sealant on the end of the collar before attaching the liner to the flue collar. Fasten it
with two clamps then adjust fastener plate all the way
to the back before sliding flue gas plate back onto the
unit. (Figs. 14 and 15)
3. After the flue collar plate is set on the cabinet top, make
sure the front edge of the flue collar plate is completely
in contact with the back edge of the cabinet top. (Fig.
16)
4. Put the machine screw back into the fastener plate.
Bolt the plate until it is locked. (Fig. 17)
Under no circumstances should insulation
be put between the damper and the top of
the unit. This may cause condensation and
overheating of the unit.
FP1280
Fig. 10 Liner installation.
FP1280
Spring located in RHEDV
between the liner vent termination
and chimney kit 1/03
Air Intake
HEDVCAK
Installation
6ft.
(183cm)
Secure this
kit with three
(3) screws
provided
Exhaust
HEZC Zero
Clearance Kit
FP1280a
10
Fig. 11 Liner installation with zero clearance kit.
FP1280a
LHEDV
vent termination
w/zero clearance kit
4/03
10004894
LHEDV Series Direct Vent Insert
Flue gas exits
through the vent
termination rain
cap
Damper
Outside combustion air enters
through the lower
level of the vent
termination
Secure with
clamp and
three screws
3" Flex Vent
Two Pieces
1) Attach flexible pipe
to rain cap
2) Secure with clamp
3) Attach raincap to
vent termination using
three screws
Clamps &
Screw
Fastener
Plate
Pull flexible pipe
through vent termination
A or B Vent with
7" Inside Minimum and
14" Outside Maximum
NOTE:
Minimum Vent Height - 12
feet
Maximum Vent Height
- 35 feet
Gasket
FP1282
Unit
Fig. 14 Apply high temperature sealant to end of collar.
Damper
Front
Frame
3" Chimney Liner
Two Pieces
FP1282
flue collar seal
1/03
Clamps &
screw
Flue Collar
Plate
Air Intake
Unit
Exhaust
Air intake collar with
label secured with
clamp and three
screws
Exhaust collar secured with clamp and
three screws
Fig. 15 Fasten with two clamps, adjust fastener plate all the
way back.
Flue
Collar
Plate
FP1280b
Fig. 12 Liner installatin with A or B vent.
Flue Collar
Plate
FP1280
RHEDV
vent termination
1/03
FP1284
Fastener
Plate
Cabinet
Top
FP1283
FP1283
unit in place
1/03
Fastener Plate
Cabinet
Top
Make sure the flue collar
plate is in contact with the
back edge of the cabinet
top
Fig. 16 The flue collar plate must be completely in contact
with back edge of cabinet top.
Plate Flue
Collar
FP1284
Fastener Plate
RHEDV flue collar
plate in place
1/03
Cabinet Top
10/24" x 1Z\x"
Machine Screw
FP1281
Fig. 13 Remove flue collar plate assembly.
FP1285
Machine Screw After
Fastened
Fig. 17 Use machine screw to bolt fastener plate in place.
10004894
FP1281
Flue collar plate
FP1285
flue collar plate
in place
11
LHEDV Series Direct Vent Insert
Round Vent Termination Installation
Ceramic Refractory Installation
Round Vent Termination Model HEDVRT is designed
to be installed onto the LHECDV20, LHERDV20, LHECDV30 and LHERDV30 direct vent insert fireplaces.
This round vent termination is built to be installed onto
any type A-vent round chimney or B-vent round chimney.
The minimum inside venting diameter must be at least
7" (178 mm) and the maximum outside diameter venting
should not exceed 14" (356 mm).
1. Remove front glass.
2. Remove logs from unit.
3. Remove refractory from package.
Refractory are fragile and must be handled
with care. Where at all possible, two hands
should be used when handling.
4.Take center refractory and tilt so bottom edge seats onto
the rear log bracket at the back wall of the fireplace.
(Fig. 19)
5. Press center refractory to back side of fireplace and
hold in place.
6.Take left or right refractory and align it so leading edge
faces outward. (Place refractory in fireplace side and
slide it back to support the center refractory.)
7. Repeat step 6 for remaining side refractory.
8. Fasten bracket supports against refractory top to hold
side in place.
When side refractory is installed correctly, the center
refractory will be supported by the side refractory.
• The extended cap 14" (356 mm) wide is only to be
•
used when the outside diameter of the round chimney
is more than 11" (279 mm).
Install the extended cap 14" (356 mm) with the round
vent termination by setting the vent termination on
top of the extended cap, then secure it with three (3)
screws (provided) through the mounting bracket holes
and seal around the edges of the vent termination with
the silicone provided. (Fig. 18)
Secure the Cap with
Three (3) Screws
Provided
Leading Edge
Seal Around the Edges of
the Cap with Silicone
Leading Edge
Bottom Edge
FP1326
Fig. 18 Round vent termination with extended assembly.
Center
Left Side
Right Side
FP1329
Fig. 19 Ceramic refractory.
FP1326
round vent
termination
4/2/03 djt
12
FP1329
LHEDV
ceramic refractory
4/03
10004894
LHEDV Series Direct Vent Insert
Venting Components
8" x 12" Vent Termination Kit
Model: HEDVT (8" x 12" )
(Fit typical 8" x 12" and 9" x 13" flue tile)
Kit Includes:
A - 8" x 12" Vent Termination (x1)
B - Stainless Steel Clamps (x4)
C - Hardware Package (x1)
B
A
C
12" x 12" Vent Termination Kit
Model: HEDVT (12" x 12")
(Fit typical 12"-13" x 12"-13" flue tile)
Kit Includes:
A - Vent Termination SL (x1)
B - Stainless Steel Clamps 3"-3.5" (x4)
C - Hardware Package (x1)
FP1298
RHEDV
B
vent components
2/03
A
High Temperature Sealant
C
D
B
FP1299
RHEDV
vent components
2/03
F
C
A
D
FP1327
vent components
4/03
FP1300
Flex pipe
2/03
Round Vent Termination Kit
Model: HEDVRT
(Fits typical A or B Vent with minimum 7" (178 mm) inside
diameter and 14" (357 mm) maximum outside diameter)
Kit Includes:
A - Round Vent Termination
B - Stainless Steel Clamps 3" - 3Z\x" (4)
C - Hardware Package (1)
D - Extended Cap 14" (1)
E - Blanket Insulation (1) (not shown)
F - Rain Cap 3" (1)
Flex Vent Kit
Model: HEDVK25
Kit Includes:
Two (2) 3" Dia. x 25 ft. long, compressed flex
vent
NOTE: Air intake has a blue line on the vent.
Flex Vent Kit
Model: HEDVK35
Kit Includes:
Two (2) 3" Dia. x 35 ft. long, compressed flex
vent
NOTE: Air intake has a blue line on the vent.
13
10004894
FP1300
LHEDV Series Direct Vent Insert
Operating Instructions
General Glass Information
Glass Frame Removal
Only ceramic glass approved by Vermont
Castings Group may be used for replacement
on this unit.
1.
The use of substitute glass will void all product
warranties.
2. Care must be taken to avoid breakage of the glass.
3. Under no circumstances should this appliance be
operated without glass properly installed, or with any
cracked or broken glass. Replacement of any glass
assembly as supplied by the manufacturer should be
done by a licensed qualified service person.
LHECDV20 and LHERDV20
1. Remove two (2) screws at the bottom of the frame.
(Fig. 17)
2. Lift up and unhook glass frame at the top.
LHECDV30 and LHERDV30
1.Unhook the frame window by pulling the handle of the
two (2) latches at the bottom part of the window frame;
pull the left side latch counterclockwise and the right
side latch, clockwise. (Fig. 21)
2. Lift and unhook the glass frame at the top.
7!2.).'
(/4',!337),,
#!53%"52.3
$/./44/5#(',!33
5.4),#//,%$
.%6%2!,,/7#(),$2%.
4/4/5#(',!33
Machine Screw
Louvre Removal
To remove louvre,
lift louvre up and
then pull out.
(Fig. 20)
2.
1.
Louvre
Glass Panel
FP444
Fig. 20 Louvre removal.
Glass Cleaning
It will be necessary to clean the glass periodically. During
start-up condensation, which is normal, forms on the inside
of the glass and causes lint, dust and other airborne particles
cling to the glass surface. Also initial paint curing may deposit
a slight film on the glass. It is therefore recommended that
the glass be cleaned two or three times with a non-ammonia
household cleaner and warm water (we recommend gas
fireplace glass cleaner). After that the glass should be
cleaned two or three times during each heating season
depending on the circumstances present.
Clean glass after first two weeks of operation.
14
Latch
FP1328
Fig. 21 Remove glass frame.
Log Installation and Burner Lava Rock
FP1327
1 .Remove glasswindow
frame.
(See
"Glass Removal" section)
frame
removal
4/3/03 djt
2. Remove logs from packaging.
3. Place logs according to the model instructions below:
LHECDV20, LHERDV20 (Fig. 22)
a. Place rear left log (JR7). Use the log's bottom holes
to locate it onto one pin stud of the rear log bracket
on the left and the other end of the log will sit on top
of the lid of the left log support.
b. Place rear right log (JR8). Use the log's bottom holes
to locate it onto the two (2) pin studs of the rear log
bracket on the right.
c. Place the front left log (JR9). Position the log notch
against the second grate from the left, and the other
edge of the log on top of the rear left log notch. Ensure
the log is secure in place.
10004894
LHEDV Series Direct Vent Insert
d. Place the front right log (JR10). Position the
Figure 22
log notch against the third grate from the right,
LHECDV20 and LHERDV20
and the other edge of the log on top of the JR7
rear right log notch. Ensure the log is secure
in place.
e. Place the burner lava rock on the front area
of the burner housing. (Fig. 22)
LHECDV30, LHERDV30 (Fig. 23)
a. Place the rear center log (KR24).
Use the log's bottom holes to locate JR9
it onto the two (2) pin studs of the
rear log bracket on the center.
b. Place rear left log (KR22). Use the log's
bottom holes to locate it onto the two (2) pin
studs of the rear log bracket on the left.
c. Place rear right log (KR23). Use the log's
bottom holes to locate it onto the two (2) pin
studs of the rear log bracket on the right.
Burner Lava Rock
d. Place the front left log (KR25). Position the log
notch against the second grate from the Figure 23
KR24
left, and the other edge of the log on top LHECDV30 and LHERDV30
KR25
of the rear left log notch. Ensure the log
is secure in place.
LG285
e. Place the front right log (KR26). Position KR22
LHEDV20
the log notch against the third grate from
the right, and the other edge of the log
logs
on top of the rear right log notch. Ensure
4/03
the log is secure in place.
f. Place the burner lava rock on the front area
of the burner housing. (Fig. 23)
JR8
JR10
KR23
KR26
Burner Lava
Rock
Front Grate
Under no circumstances should these
lava rocks be placed on top of the burner
assembly.
Flame Adjustment (RN/RP Models)
For fireplaces equipped with HI/LO valves, flame adjustment
is accomplished by rotating the HI/LO adjustment knob
located near the center of the gas control. (Figs. 24 or
25)
10004894
Turn
LG286
LHEDV30
counterclockwise
to Logs
decrease
4/03
flame height
"
The large lava rock provided with this fireplace should be
placed on the firebox base on either side of the burner
assembly.
LG286
Honeywell Valve
Turn clockwise
to increase
flame height
Fig. 24 Flame adjustment knob for Honeywell Valve.
Turn
counterclockwise
to increase
flame height
HI
Large Lava Rock Placement
LG285
Front Grate
Turn clockwise
to decrease
flame height
HV102
LO
Honeywell hi/lo knob
4/5/99 djt
Fig. 25 Flame adjustment knob for SIT valve.
FP390
FLAME ADJUSTMENT KNOB
11/21/96
15
LHEDV Series Direct Vent Insert
Flame Characteristics
First Firing
It is important to periodically perform a visual check of the
pilot and the burner flames. Compare them to the Figure 26
and Figure 27 or 28. If any of the flames appear abnormal
call a service person.
Upon completing the gas line connection, a small amount
of air will be in the lines. When first lighting unit with pilot
light, it will take a few minutes to purge themselves of this
air. Once the purging is complete, the pilot and burner will
light and operate as indicated in the instruction manual.
Subsequent lightings of the heater will not require such
purging.
PSE Pilot
3/8" - 1/2"
When lit for the first time, the appliance will emit a slight
odor for awhile. This is due to paint and lubricants used in
the manufacturing process. After each lighting, vapor may
condense and fog the glass; this moisture disappears within
a few minutes of burning.
SIT Pilot
F584-703
Fig. 26 Correct pilot flame appearance.
Figure 27
LHECDV20 and LHERDV20
F584-703
Honeywell
& PSE
pilot flames
LG287
Figure 28
LHECDV30 and LHERDV30
LG287
LHEDV20
log flames
4/03
LG288
16
10004894
LG288
LHEDV30
LHEDV Series Direct Vent Insert
Lighting and Operating Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A.This heater has a pilot which must be lit manually. When
lighting the pilot follow these instructions exactly.
B. BEFORE LIGHTING smell all around the heater area
for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the
floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any fireplace
• Do not touch any electric switch
• Do not use any phone in your building
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the Fire
Department
C.Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, do not try to repair it, call a qualified
service technician. Applying force or any attempted
repair may result in a fire or explosion.
D.Do not use this fireplace if any part has been under
water. Immediately call a qualified service technician
to inspect the heater and to replace any part of the
control system and any gas control which has been
under water.
Lighting Instructions
1. STOP! Read the safety information above.
2.Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to Step
4. For RN/RP appliances turn the On/Off switch to
“OFF” position or set thermostat to lowest level.
4. Open control access panel.
5. Push in gas control knob slightly and turn clockwise
to "OFF".
10. Push the control knob all the way in and hold. Immediately light the pilot by repeatedly depressing the
piezo spark ignitor until a flame appears. Continue
to hold the control knob in for about one (1) minute
after the pilot is lit. Release knob and it will pop back
up. Pilot should remain lit. If it goes out, repeat steps
5 through 8.
3/8" - 1/2"
ON
OFF
OFF
OFF
3 4 5
Euro SIT
OT
L
PI
ON
1 2
P
OFF ilot
PILOT
SIT NOVA
Honeywell
6. Wait five (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
STOP! Follow "B"FP1067
in the safety information above.
If you do not smelllighting
gas, instruction
go to the next step.
knobs
7. Remove glass door
before lighting pilot. (See Glass
3/9/01 djt
Frame Removal section).
8. Visibly locate pilot by the main burner.
9.Turn knob on gas control counterclockwise
to
"PILOT".
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
FP1068
• If after several tries, the
pilot instructions
will not stay lit, turn
Lighting
the gas control knob Pilots
to " " and call your service
technician or gas supplier.
11. Replace glass door.
12.Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to “ON”
position or set thermostat to desired setting.
14.Turn on all electrical power to the fireplace.
To Turn Off Gas To Heater
1.Turn the On/Off switch to "OFF" position or set the
thermostat to lowest setting.
2.Turn off all electric power to the fireplace if service is
to be performed.
10004894
3. Open control access panel.
4. Push in gas control knob slightly and turn clockwise
to "OFF". Do not force.
5. Close control access panel.
17
LHEDV Series Direct Vent Insert
Troubleshooting the Gas Control System
SIT NOVA 820 Millivolt Valve
NOTE: Before trouble shooting the gas control system, be sure external gas shut off is in the “On” position.
WARNING: Before doing any gas control service work, remove glass front.
SYMPTOM POSSIBLE CAUSES
CORRECTIVE ACTION
1.Spark ignitor will not light
A. Defective or misaligned Using a match, light pilot. If pilot lights, turn off electrode at pilot.
pilot and push the red button again. If pilot will not light - check gap at electrode and pilot-should be 1/8" to have a strong spark.
B. Defective ignitor (Push Button) Push Piezo Ignitor Button. Check for spark at electrode and pilot. If no spark to pilot, and elec
trode wire is properly connected, replace ignitor.
2. Pilot will not stay lit after
A. Defective pilot generator
Check pilot flame. Must impinge on thermo
carefully following lighting (thermocouple), remote wall couple/thermopile. Note: this pilot burner assem
instructions. switch.
bly utilizes both-a thermocouple and a thermopile. The thermocouple operates the main valve operation (On and Off). Clean and or adjust pilot for maximum flame impingement on thermopile and thermocouple.
B. Defective automatic valveTurn valve knob to “Pilot”. Maintain flow to pilot; milivolt meter should read greater than 10 mV. If the reading is okay and the pilot does not stay on, replace the gas valve. Note: An interrupter block (not supplied) must be used to conduct this test.
3. Pilot burning, no gas to
A. Wall switch or wires defective
Check wall switch and wires for proper connec
main burner
tions. Jumper wire accross terminals at wall switch, if burner comes on, replace defective wall switch. If okay, jumper wires across wall switch wires at valve, if burner comes on, wires are faulty or connections are bad.
B. Thermopile may not be
1. Be sure wire connections from thermopile at generating sufficient gas valve terminals are tight and thermopile is millivoltage. fully inserted into pilot bracket.
2. One of the wall switch wires may be grounded. Remove wall switch wires from valve terminals if pilot now stays lit, trace wall switch wiring for ground. May be grounded to fireplace or gas supply.
3. Check thermopile with millivolt meter. Take reading at thermopile terminals of gas valve. Should read 250-300 millivolts (minimum 150) while holding valve knob depressed in pilot position and wall switch “Off”. Replace faulty thermopile if reading is below specified minimum.
C. Plugged burner orifice.
Check burner orifices for debris and remove.
D. Defective automatic valve Turn valve knob to “On”, place wall switch to “On” operator.
millivolt meter should read greater than 100 mV. If the reading is okay and the burner does not come on, replace the gas valve.
4. Frequent pilot outage
A.Pilot flame may be too low
Clean and/or adjust pilot flame for maximum flame
problem. or blowing (high) causing the
impingement on thermopile and thermocouple.
pilot safety to drop out.
B.Possible blockage of the vent
Check the vent terminal for blockage (recycling the terminal.
flue gases)
18
10004894
LHEDV Series Direct Vent Insert
Troubleshooting the Gas Control System
Honeywell Millivolt Valve
START
Gas Supply On
CHECK
NO
Supply Line Hooked Up
Shutoff Valve Open
YES
Pilot Lights With
Piezo Ignitor
NO
YES
Pilot Stays Lit
NO
Lockout Has Engaged. Wait
60 Seconds And Try Again.
For Spark At Electrode While
Depressing Piezo — 1/8" Gap To
Pilot Hood Needed.
All Wiring Connections
Replace Piezo Ignitor
For Air In The Lines
Thermopile Needs A Minimum
325mv. Adjust Pilot Flame Height.
All Wiring Connections.
Replace Thermopile
Thermocouple Needs A Minimum
of 14mv.
Defective Valve. Turn To Pilot,
Meter Should Read Greater Than
100 Mv. If Not, Replace.
YES
Pilot Lights Main
Burner
YES
NO
Valve Is Turned On
On/off Switch Is Not Turned On.
Watch For Grounded Wires!
Thermopile Needs A Minimum
325mv.
Plugged Burner Orifice.
System OK.
FP396
NVC-standing pilot troubleshooting
11/22/96
10004894
19
LHEDV Series Direct Vent Insert
Instructions for RF Comfort Control Valve
The Comfort Control Valve allows remote control of temperature, fan and flame appearance.
NOTE: The antenna should hang in free air away from
grounded metal.
Operation
1. If the manual switch is in remote position, switch it to
LOCAL. (Fig. 25)
2.Turn the pilotstat knob counterclockwise from OFF to
the PILOT position, push the knob down, and hold in
position. The pilot valve opens and allows gas to flow
to the pilot burner.
3. Push plunger on the piezo until the pilot burner is lit.
When the pilot burner is lit, the LED on the control will
come on after approximately 40 seconds and will be
continuously red. When the light turns off which will be
approximately 10 seconds after it has been continuously
red, the receiver/valve is fully powered.
7. If the manual switch is in the LOCAL position, the valve
will be at the highest fixed pressure setting. The transmitter will control the fan only.
Shut Off Procedure
If the manual switch is in the REMOTE position, the transmitter can shut off the main burner and fan. However, the
control is still on and a command from the transmitter can
turn on the main burner or fan.
To shut off the system, turn the pilotstat knob clockwise
to the OFF position. This action closes the main gas and
safety valves. The transmitter cannot turn on the main
burner or fan.
Transmitter Operation
Off Mode
In the OFF mode, the fireplace flame and fan are off, the
display will show OFF and displays the room temperature.
If the receiver is in REMOTE mode, the fireplace will shut
off.
Piezo Ignitor
OFF
•
D
Countdown
Timer
LE
REMOTE
LOCAL
O
• N
OT
PIL
Mode
Auto
On
Off
LED
Local/Remote
Switch
Fan
Pilotstat Knob
Antenna
FP1037
Fig. 25 Comfort conrol valve.
FP1037
Honeywell
4. Release the knob.
The shaft will move upward. The pilot
burner shouldcomfort
now stayvalve
burning. If the pilot burner goes
3/22/00
djt
out, repeat step
2.
5.Turn the knob counterclockwise to the ON position. If
the manual switch is in the LOCAL position, the main
burner will turn on immediately.
6. ON the initial use of a transmitter, a recognition operation is required between the receiver/valve and transmitter. Change the switch from LOCAL to REMOTE.
Press the fan or flame button on the transmitter within
30 seconds. The LED will blink indicating the transmitter will now work with the receiver/valve. If the switch
continues in the REMOTE position, the transmitter will
now control the main valve, flame modulation level and
fan control.
20
FP1039
Display
Room Temperature
Set Temperature
Flame Height Level
Fan Speed Level
Countdown Timer
Low Battery
Flame
Up
Increases Flame
Height, Fan Speed
Timer, or Set Point
Down
Decrease
Flame, Fan
Speed Timer
or Set Point
Fig. 26 Transmitter diagram.
FP1039
On (Manual) Mode
comfort valve
In the ON mode,
the room temperature, flame and fan
transmitter
levels will be shown.
will appear next to both the
3/27/00MANUAL
djt
flame and fan icons.
When the control is in the ON mode, the flame and fan
levels, and delay timer are changed with the up and down
buttons. To change the flame level, press the flame button
followed by an arrow key. To change the fan level, press
the fan key followed by an arrow key. Pushing the arrow
key once will change the level by one unit.
10004894
LHEDV Series Direct Vent Insert
Delay Timer Mode
Pilot Assembly
The shut off delay timer has a maximum of 2 hours and a
minimum of zero minutes. To change the timer level, press
the time key followed by an arrow key. Pushing the key
once will change the timer by 10 minutes.
Fan
Auto Mode
In the AUTO mode, the room temperature, set temperature,
flame and fan levels will be shown. AUTO will appear next
to both the flame and fan icons.
In the AUTO mode, the fan speed will increase with increasing flame height or decrease with decreasing flame height.
“AUTO” is displayed next to the flame and fan icons.
Fan Override During Auto Mode
If a lower or higher fan speed is desired when operating
in the AUTO mode, the fan speed can be overridden by
pushing the fan button followed by the up or down key.
Pushing a key once will change the fan level by one unit.
In this mode “AUTO” is displayed next to the flame icon
and “MANUAL” is displayed next to the fan icon.
Change Between F/C Temperature Units
Push the up and down arrow keys simultaneously for at
least 3 seconds to toggle between Fahrenheit and Celsius
units.
Disable Thermostat Function
To disable the thermostat function in the AUTO mode,
push the time and down keys simultaneously for at least
3 seconds.
To Change Batteries
1. Remove cover on the backside of the transmitter. Install
3 AAA batteries as shown and reattach cover.
2. Once steps 1-3 in OPERATION are completed, receiver/
valve and transmitter are now ready. Press any button
on transmitter for recognition process to occur between
the receiver/valve and transmitter.
3.Use functions as described in TRANSMITTER section.
Red
White
FAN
When the control is in the AUTO mode, the main burner
will turn on/off or modulate based on the heat needed to
maintain the set temperature. The flame level will change
automatically to optimize the heat output needed to maintain the set temperature. To change the set temperature,
press the up or down key. Pushing a key once will change
the temperature by one degree.
Red
White
White Dots
Antenna
FP1038
Valve
(Bottom View)
Fig. 27 Comfort Valve wiring diagram.
FP1038
Troubleshooting
comfort valve
1. Locate LED light on valve. wiring diagram
3/24/00
djt received by
2. LED will blink after every valid
command
the transmitter; this is not an error.
3. Failure codes may occur anytime after pilot burner is
lit.
4.Sequence is failure code followed by light not blinking
for 30 seconds.
5. In the event of multiple failure codes, next failure code
follows previous failure code by approximately 3 seconds.
If an Error Code 3 is observed while performing the
testing, complete the following:
1. Make sure the spade connectors are pushed all the way
on. If the Error Code 3 is still showing, then go to the
next step.
2.Switch the front two thermopile leads with the back two.
Be sure the white lead is connected to the spade with
the white dot next to it. If the Error Code 3 is still showing, replace the thermopiles.
If an Error Code 8 is observed while performing the
testing, complete the following:
1. Confirm the valve is not in REMOTE mode.
• If the valve is producing Error Code 8 and in REMOTE mode, the valve is defective and should be
replaced.
• If the valve is in LOCAL mode and producing Error
Code 8, then go to the next step.
10004894
21
LHEDV Series Direct Vent Insert
2.Slide the Remote/Local switch to REMOTE and teach
the valve a transmitter (refer to Item 6, page 1). The Error Code will clear itself after approximately 1¹⁄₂ minutes
and return to normal operation.
LED Count
Service Action
Replace valve
Auto Path
If the manual switch is
set to REMOTE, press
the mode button to
display AUTO on the
transmitter. Does the
transmitter display the
room and temperature
setting?
8
7
exists
Confirm stepper motor connection 5
works
Confirm fan connection exists and 4
Confirm gas type; jumper in place
Yes
3
Replace thermopiles
If the setting is above
room temperature on
the transmitter, does the
main valve and fan turn
on?
2Turn fan ON
NOTE: Some keys are not active.
Move switch
from LOCAL to
REMOTE. Press
any key within 30
seconds.
No
Yes
If the setting is below
room temperature on
the transmitter, does
the main valve and fan
turn off?
No
Turn pilotstat knob
to OFF to turn valve
completely off
22
10004894
LHEDV Series Direct Vent Insert
Comfort Valve system control sequence of operation with transmitter
Set manual switch
to local or remote
Five minute wait
period
Light pilot burner
Did the LED stop
blinking?
No
Review LED failure analysis
Release pilotstat
knob
Yes
Turn pilotstat knob
from PILOT to ON
Move switch from
local to remote.
Press any key on
transmitter. Move
switch back to
local
Yes
Transmitter controls fan
Yes
Turn pilotstat knob
to PILOT to turn
off main burner
Turn pilotstat knob
to OFF to turn
valve completely
off
No
Choose Local or
Remote path. Set
switch to manual or
remote
On Path
Local Path
If manual switch is
set to local, did
main burner light?
Cycle switch
once and leave in
remote. Press any
key on transmitter for recognition
operation
If the manual switch
is set to REMOTE,
press the mode button to display "ON".
Does transmitter control the main burner
and fan?
Move switch from
manual to remote.
Press any key on
transmitter.
Yes
Does transmitter
change levels of
flame height, fan
speed and set
temperature?
No
Yes
Set levels of flame
height and fan to
“0” to shut off main
burner and fan
Turn pilotstat knob
to OFF to turn
valve completely
off
10004894
23
LHEDV Series Direct Vent Insert
Maintenance
Burner and Burner Compartment
It is important to keep the burner and the burner compartment
clean. At least once per year the logs and lava rock/ember
material should be removed and the burner compartment
vacuumed and wiped out. Remove and replace the logs
as per the instructions in this manual.
Always handle the logs with care as they are fragile
and may also be hot if the fireplace has been
in use.
Fan Assembly
The fan unit requires periodic cleaning. At least once per
month in the operating season, open the lower louvre panels
and wipe or vacuum the area around the fan to remove
any build up of dust or lint.
Cleaning the Standing Pilot
Control System
The burner and control system consists of:
• main burner
• pilot burner
• gas orifice
• thermopile
• combination millivolt gas valve
In order to properly clean the burner and pilot assembly,
turn off the gas to the unit, remove the window frame panel
and logs exposing the burner and pilot assembly. Clean
all foreign materials from the top of the burner. Check to
make sure that burner parts are clean. Visually inspect pilot.
Brush or blow away any dust or lint accumulation. If pilot
orifice is plugged, disassembly may be required to remove
any foreign material from the orifice or tubing.
To obtain proper operation, it is imperative that the pilot
and burner's flame characteristics are steady, not lifting
or floating.
Typically, the top 1/8" of the thermopile should be engulfed
in the pilot flame. (Page 12, Fig. 22)
Trim Cleaning
Clean the trim with a soft clean cloth, slightly dampened
with lemon oil and buff with a soft dry cloth. Do not use
brass polish or household cleaners as these products will
damage the trim. Lemon oil can be obtained at supermarkets or hardware stores.
Most of these components may require only an occasional
checkup and cleaning and some may require adjustment.
If repair is necessary, it should be performed by a qualified
technician.
24
10004894
LHEDV Series Direct Vent Insert
LHERDV20/LHECDV20
10a/b
1b
4
2
1a
3
18
5
1e
16
14
1d
6a/b
LHERDV30/LHECDV30
1c
18
17
8a/b
1b
1a
19
11a/b
7a/b
13a/b
9 a/b
1e
1d
20
15
21
22a/b
12a/b
*
27
" *"/
"
"/
28/29
"
30
24a/b
OT
23 a/b
26
OFF
•
41
LE
D
REMOTE
LOCAL
ON
•
PIL
25
40
46
35
32
31
33
44
42
34
45
48
43
51
36
37
47
50
49
38
4894
Vermont Castings Group reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any
time, without notice.
LHEDV Series
10004894
4894
LHEDV
parts
4/03
25
LHEDV Series Direct Vent Insert
LHEDV Series (continued)
Ref. Description
LHERDV20
LHECDV20
LHERDV30
LHECDV30
1. Log Set Complete
10005332
10005332
10004866
10004866
1a. Log Rear Left
10005333 (JR7)
10005333 (JR7) 10004874 (KR22) 10004874 (KR22)
1b. Log Rear Right
10005334 (JR8)
10005334 (JR8) 10004875 (KR23) 10004875 (KR23)
1c. Log Rear Center
-
-
10004876 (KR24) 10004876 (KR24)
1d. Log Front Left
10005335 (JR9)
10005335 (JR9) 10004878 (KR25) 10004878 (KR25)
1e. Log Front Right
10005336 (JR10) 10005336 (JR10) 10004879 (KR26) 10004879 (KR26)
2. Lava Rock Burner Package
57897
57897
57897
57897
3. Lava Rock Package
-
-
10001454
10001454
4. Burner Housing Assembly with Tiles
10005294
10005294
10004972
10004972
5. Ceramic Tile (Single)
57803
57803
57803
57803
6a. Orifice Front Burner (Nat.)See Rating Plate for Orifice Size
6b. Orifice Front Burner (Prop)See Rating Plate for Orifice Size
7a. Orifice Rear Burner (Nat.)See Rating Plate for Orifice Size
7b. Orifice Rear Burner (Prop.)See Rating Plate for Orifice Size
8a. Orifice Pilot SIT Top Convertible
10002268
10002268
10002268
10002268
8b. Orifice Pilot SIT Top Convertible
10002269
10002269
10002269
10002269
9a. Orifice Pilot PSE (Nat.)
10001822
10001822
10001822
10001822
9b. Orifice Pilot PSE (Prop.)
10001823
10001823
10001823
10001823
10a. Pilot Assembly SIT Top Convertible (Nat.)
10002264
10002264
10002264
10002264
10b. Pilot Assembly SIT Top Convertible (Prop.)
10002265
10002265
10002265
10002265
11a. Pilot Assembly PSE ( Nat.)
10001741
10001741
10001741
10001741
11b. Pilot Assembly PSE (Prop.)
10001742
10001742
10001742
10001742
12a. Pilot Assembly RFN (Nat.)
-20002266
-20002266
12b. Pilot Assembly RFP (Prop.)
-20002268
-20002268
13a. Pilot Orifice RFN (Nat.)
-20000908
-20000908
13b. Pilot Orifice RFP (Prop.)
-20000907
-20000907
14. Pilot Tubing w/Fittings
10001296
10001296
10001296
10001296
15. Manifold Tubing w/Fittings
57318
57318
57318
57318
16.Thermocouple SIT
53373
53373
53373
53373
17.Thermocouple PSE
10001825
10001825
10001825
10001825
18.Thermopile
51827
51827
51827
51827
19.Electrode Ignitor w/Cable SIT
10001297
10001297
10001297
10001297
20. Ignitor Piezo SIT
52464
52464
52464
52464
21. Ignitor Piezo Honeywell20000062200000622000006220000062
22a. Valve SIT 820 RN
52677
52677
52677
52677
22b. Valve SIT 820 RP
52678
52678
52678
52678
23a. Valve Honeywell RN
10001782
10001782
10001782
10001782
23b. Valve Honeywell RP
10001759
10001759
10001759
10001759
24a. Valve Honeywell RFN
-20003719
-20003719
24b. Valve Honeywell RFP
-20003720
-20003720
25. Antennae (for RFN or RFP Units)
-20003561
-20003561
26.Transmitter (for RFN or RFP Units)
-20002047
-20002047
27.Thermopile (for RFN or RFP Units)
-20002400
-20002400
28. Cord Set (for RFN or RFP Units)
-20002541
-20002541
29. Cord Set (for RN or RP Units)
51865
51865
51865
51865
30. Fan with Bracket
-
54103
-
54103
31. Fan Temperature Sensor (for RN orRP Units)
-
51704
-
51704
32. Fan Speed Control Switch (for RN or RP Units)
-
51738
-
51738
33.Speed Control Knob (for RN or RP Units)
-
51882
-
51882
34. Glass with Gasket
10005297
10005066
10006888
10004870
35. Gasket Glass
57317
57317
57317
57317
36. Frame Window
10005295
10005067
10006887
10004873
26
10004894
LHEDV Series Direct Vent Insert
LHE Series (continued)
Ref. Description
LHER20
LHEC20
LHER30
LHEC30
37. Remote Switch (for RN or RP Units)
53606
53606
53606
53606
38. Remote Wire Harness w/Terminals (for RN or RP Units)
10002582
10002582
10002582
10002582
39. Ceramic Fiber Brick FP (Optional)
JT1TR0
JT1TC0
KT1TR0
KT1TC0
40. Gasket Fan Cover
-
-
-
10003486
41. Flexible Connector (6")
10005098
10005098
10005098
10005098
42. Bracket Rear Log Assembly
10005370
10005369
10006771
10005489
43. Bracket Log Support Assembly
-
-
10004885
10004885
44. Gasket Cover Gas Line Access
10004227
10004227
10004227
10004227
45. Bracket Support Grate
-
-
10003479
10003479
46. Hinge 2 Springs
52356
52356
52356
52356
47.Shield Heat Pilot
10000248
10000248
10000248
10000248
48. Plate Relief with Gasket
10002032
10002032
10002032
10002032
49. Grate Assembly Flat Black
10004967
10004967
10003478
10003478
50. Plate Relief w/Gasket Asembly (Burner Tray)
-
-
10004192
10004192
51. Bracket ON/OFF Switch
10005035
10005035
10005035
10005035
10004894
27
LHEDV Series Direct Vent Insert
Optional Accessories
Remote Controls
Trim Options
Optional remote control units are available to control different functions of the appliance.
Face Kits
Model
RC1
RC2
IMTFK
Function(s) Controlled
ON/OFF
ON/OFF and Temperature
Wall mounted thermostat control
NOTE: These remote controls are for RN/RP units only.
Zero Clearance Kit
For installations other than in existing woodburning fireplaces such as new construction or renovation projects,
a Zero Clearance Kit must be used. The HEZC enables
these inserts to be installed in combustible environments.
Consideration must be given to the dimensions of the Zero
Clearance Kit and the requirements of the Air Kit when
planning out the installation.
Follow the instructions supplied with the Zero Clearance
Kit carefully for proper installation.
Arch Door Kits
Model
LHEC20DKB
LHEC30DKB
LHEC30DKS
Description
Arch Door, Black
Arch Door, Black
Arch Door, Pewter
Ceramic Firebox Liners
28
Model
LHER20CR
LHEC20CR
LHEC30CR
LHER30CR
Description
Ceramic Fiber Brick
Ceramic Fiber Brick
Ceramic Fiber Brick
Ceramic Fiber Brick
NOTE: One is required for LHEC20 and LHEC30
Model
Description
LHEC20FB
Louvre T&B, Black
LHEC20LKB
Filigree T&B, Black
LHEC20LKS
Filigree T&B, Pewter
LHEC30FB
Louvre T&B, Black
LHEC30LKB
Filigree T&B, Black
LHEC30LKS
Filigree T&B, Pewter
LHEC30LKG
Filigree T&B, Gold
LHEC20CBTK
Cast Bay Window, Classic Black
LHER20BTK
Bay Window w/Louvres,Black
HECBTKADK
Window Adapter Kit LC30
LHEC30CBTK
Cast Bay Window, Classic Black
LHEC30BTK
Bay Window w/Filigree, Black
LHER30BTKSteel Bay w/Filigree, Black
Trim Kits
NOTE: One is required.
Model
Description
LHE20SSBSmall Surround, Black
LHE20SLB
Large Surround, Black
LHE20TCKTrim Closure Kit, Black, XL
LHEABSL
Adjust Bevel Steel/Cast
LHE20CSLB
Large Cast Surround, Classic Black
LHE30SSBSmall Surround, Black
LHE30SLB
Large Surround, Black
LHE30SLGA
Large Surround, w/Gold Edge
LHE30TCKTrim Closure Kit, Black XL
MEAD3CM
Large Cast Surround, Classic Black
MEAD3EB
Large Cast Surround, Ebony
MEAD3EBS
Large Cast Surround, Biscuit
CAPCB
Adjust. Cast Cont. Surround,
Classic Black
CAPEB
Adjust. Cast.Cont. Surround, Ebony
10004894
LHEDV Series Direct Vent Insert
10004894
29
LHEDV Series Direct Vent Insert
30
10004894
LHEDV Series Direct Vent Insert
Limited lifetime warranty policy
Lifetime Warranty
The following components are warranted for life to the original owner, subject to proof of purchase: Firebox,
Combustion Chamber, Heat Exchanger, Grate and Stainless Steel Burners.
Five Year Warranty
The following components are warranted five (5) years to the original owner, subject of proof of purchase:
Ceramic Fiber Logs.
Basic Warranty
Vermont Castings Group warrants the components and materials in your gas appliance to be free from manufacturing and material defects for a period of two years from date of installation. After installation, if any of the
components manufactured by Vermont Castings Group in the appliance are found to be defective in materials or workmanship, Vermont Castings Group will, at its option, replace or repair the defective components
at no charge to the original owner. Vermont Castings Group will also pay for reasonable labor costs incurred
in replacing or repairing such components for a period of two years from date of installation. Any products
presented for warranty repair must be accompanied by a dated proof of purchase.
This Limited Lifetime Warranty will be void if the appliance in not installed by a qualified installer in accordance with the installation instructions. The Limited Lifetime Warranty will also be void if the appliance is not
operated and maintained according to the operating instructions supplied with the appliance, and does not
extend to (1) firebox/burner assembly damage by accident, neglect, misuse, abuse, alterations, negligence
of others, including the installation thereof by unqualified installers, (2) the costs of removal, reinstallation or
transportation of defective parts on the appliance, or (3) incidental or consequential damage. All service work
must be performed by an authorized service representative.
This warranty is expressly in lieu of other warranties, express or implied, including the warranty of merchantability of fitness for purpose and of all other obligations or liabilities. Vermont Castings Group does not assume
for it any other obligations or liabilities in connection with sale or use of the appliance. It states that do not
allow limitations on how long an implied warranty lasts, or do not allow exclusion of indirect damage, those
limitations of exclusions may not apply to you. You may also have additional rights not covered in the Limited
Lifetime Warranty.
Vermont Castings Group reserves the right to investigate any and all the claims against the Limited Lifetime
Warranty and decide upon method of settlement.
IF WARRANTY SERVICE IS NEEDED...
1. Contact your supplier. Make sure you have your warranty, your sales receipt and the model/
serial number of your Vermont Castings Group product.
2. DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.
10004894
31
Efficiency Ratings
Model
LHECDV20RN
LHECDV20RP
LHECDV20RFN
LHECDV30RFP
LHERDV20RN
LHERDV20RP
LHECDV30RN
LHECDV30RP
LHECDV30RFN
LHECDV30RFP
LHERDV30RN
LHERDV30RP
EnerGuide Ratings
Fireplace Efficiency (%)
61.3
61.3
61.3
61.3
59.7
59.7
61.5
61.5
61.5
61.5
64.1
64.1
Steady State (%)
Fan-OFF
Fan-ON
69
72
70
73
69
72
70
73
69
N/A
70
N/A
70
73
71
74
70
73
71
74
69
N/A
70
N/A
Vermont Castings Group
149 Cleveland Drive • Paris, Kentucky 40361
www.vermontcastingsgroup.com
D.O.E.
(AFUE%)
65
65
65
65
64
64
66
66
66
66
65
65
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement