Appendix D - AutomationDirect

Appendix D - AutomationDirect
Special Relays
In This Appendix. . . .
— DL350 CPU Special Relays
1D
Special Relays
DL350 CPU Special Relays
Startup and
Real-Time Relays
CPU Status Relays
SP0
First scan
on for the first scan after a power cycle or program to run transition
only. The relay is reset to off on the second scan. It is useful where a
function needs to be performed only on program startup.
SP1
Always ON
provides a contact to insure an instruction is executed every scan.
SP2
Always OFF
provides a contact that is always off.
SP3
1 minute clock
on for 30 seconds and off for 30 seconds.
SP4
1 second clock
on for 0.5 second and off for 0.5 second.
SP5
100 ms clock
on for 50 ms. and off for 50 ms.
SP6
50 ms clock
on for 25 ms. and off for 25 ms.
SP7
Alternate scan
on every other scan.
SP11
Forced run mode on anytime the CPU switch is in the RUN position.
SP12
Terminal
run mode
on when the CPU switch is in the TERM position and the CPU is in
the RUN mode.
SP13
Test run mode
on when the CPU switch is in the TERM position and the CPU is in
the test RUN mode.
SP14
Test hold mode
on when theCPU switch is in the TERM position and the CPU is in the
TEST HOLD mode
SP15
Test program
mode
on when the CPU is in the TERM position and the CPU is in the TEST
PROGRAM MODE.
SP16
Terminal
program mode
on when the CPU switch is in the TERM position and the CPU is in
the PROGRAM MODE.
SP17
Forced stop
mode relay
on anytime the CPU mode switch is in the STOP position.
SP20
Forced
stop mode
on when the STOP instruction is executed.
SP21
Break Relay 2
on when the BREAK instructions is executed. It is OFF when the CPU
mode is changed to RUN.
SP22
Interrupt enabled
on when interrupts have been enabled using the ENI instruction.
SP25
CPU battery disabled relay
on when the CPU battery is disabled by special V--memory.
Appendix E
Special Relays
Appendix D
Special Relays
Appendix C
Special Relays
Appendix B
DL405 Error Codes
Appendix A
DL405 Error Codes
D--2
DL350 User Manual, 2nd Edition
Special Relays
Warning
on when a non-critical error such as a low battery has occurred.
SP43
Battery low
on when the CPU battery voltage is low.
SP44
Reserved
SP45
Reserved
SP46
Communications on when a communications error has occurred on any of the CPU
error
ports.
SP47
I/O configuration
error
on if an I/O configuration error has occurred. The CPU power-up I/O
configuration check must be enabled before this relay will be
functional.
SP50
Fault instruction
on when a Fault Instruction is executed.
SP51
Watch Dog
timeout
on if the CPU Watch Dog timer times out.
SP52
Grammatical
error
on if a grammatical error has occurred either while the CPU is
running or if the syntax check is run. V7755 contains the exact error
code.
SP53
Solve logic error
on if CPU cannot solve the logic.
SP54
Intelligent I/O
error
on when communications with an intelligent module has occurred.
SP60
Value less than
on when the accumulator value is less than the instruction value.
SP61
Value equal to
on when the accumulator value is equal to the instruction value.
SP62
Greater than
on when the accumulator value is greater than the instruction value.
SP63
Zero
on when the result of the instruction is zero (in the accumulator.)
SP64
Half borrow
on when the 16 bit subtraction instruction results in a borrow.
SP65
Borrow
on when the 32 bit subtraction instruction results in a borrow.
SP66
Half carry
on when the 16 bit addition instruction results in a carry.
SP67
Carry
when the 32 bit addition instruction results in a carry.
SP70
Sign
on anytime the value in the accumulator is negative.
SP71
Invalid octal
number
on when an Invalid octal number was entered. This also occurs when
the V-memory specified by a pointer (P) is not valid.
SP72
Invalid Real
Number
On when an invalid real number is in the accumulator
SP73
Overflow
on if overflow occurs in the accumulator when a signed addition or
subtraction results in a incorrect sign bit.
SP74
Underflow
On if real number underflow occurs in the accumulator
(numbers are too close to 0.0)
SP75
Data error
on if a BCD number is expected and a non--BCD number is
encountered.
SP76
Load zero
on when any instruction loads a value of zero into the accumulator.
DL350 User Manual, 2nd Edition
Appendix E
Special Relays
SP41
Appendix D
Special Relays
on when a critical error such as I/O communication loss has
occurred.
Appendix C
Special Relays
Critical error
Appendix B
DL405 Error Codes
Accumulator
Status Relays
SP40
Appendix A
DL405 Error Codes
System Monitoring
Relays
D--3
Appendix E
Special Relays
Appendix D
Special Relays
Appendix C
Special Relays
Appendix B
DL405 Error Codes
Appendix A
DL405 Error Codes
D--4
Special Relays
Communications
Monitoring Relays
SP116
DL350 CPU
communication
on when port 2 is communicating with another device
SP117
Comm error port
2
on when Port 2 has encountered a communication error.
SP120
Module busy
Slot 0
on when the communication module in slot 0 is busy transmitting or
receiving. You must use this relay with the RX or WX instructions to
prevent attempting to execute a RX or WX while the module is busy .
SP121
Com. error
Slot 0
on when the communication module in slot 0 of the local base has
encountered a communication error.
SP122
Module busy
Slot 1
on when the communication module in slot 1 of the local base is busy
transmitting or receiving. You must use this relay with the RX or WX
instructions to prevent attempting to execute a RX or WX while the
module is busy.
SP123
Com. error
Slot 1
on when the communication module in slot 1 of the local base has
encountered a communication error.
SP124
Module busy
Slot 2
on when the communication module in slot 2 of the local base is busy
transmitting or receiving. You must use this relay with the RX or WX
instructions to prevent attempting to execute a RX or WX while the
module is busy.
SP125
Com. error
Slot 2
on when the communication module in slot 2 of the local base has
encountered a communication error.
SP126
Module busy
Slot 3
on when the communication module in slot 3 of the local base is busy
transmitting or receiving. You must use this relay with the RX or WX
instructions to prevent attempting to execute a RX or WX while the
module is busy.
SP127
Com. error
Slot 3
on when the communication module in slot 3 of the local base has
encountered a communication error.
SP130
Module busy
Slot 4
on when the communication module in slot 4 of the local base is busy
transmitting or receiving. You must use this relay with the RX or WX
instructions to prevent attempting to execute a RX or WX while the
module is busy.
SP131
Com. error
Slot 4
on when the communication module in slot 4 of the local base has
encountered a communication error.
SP132
Module busy
Slot 5
on when the communication module in slot 5 of the local base is busy
transmitting or receiving. You must use this relay with the RX or WX
instructions to prevent attempting to execute a RX or WX while the
module is busy.
SP133
Com. error
Slot 5
on when the communication module in slot 5 of the local base has
encountered a communication error.
SP134
Module busy
Slot 6
on when the communication module in slot 6 of the local base is busy
transmitting or receiving. You must use this relay with the RX or WX
instructions to prevent attempting to execute a RX or WX while the
module is busy.
SP135
Com. error
Slot 6
on when the communication module in slot 6 of the local base has
encountered a communication error.
SP136
Module busy
Slot 7
on when the communication module in slot 7 of the local base is busy
transmitting or receiving. You must use this relay with the RX or WX
instructions to prevent attempting to execute a RX or WX while the
module is busy.
SP137
Com. error
Slot 7
on when the communication module in slot 7 of the local base has
encountered a communication error.
DL350 User Manual, 2nd Edition
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement