MultiBio 700 User Manual
MultiBio 700
User Manual
Version: 1.1
Date: Nov. 2010
Multi-Biometric Access Control Terminal User Manual
About This Manual
This document introduces the user interface and menu operations of Multi-Biometric
Access Control Terminal. For installation, please refer to the Installation Guide.
II
Table of Contents
Table of Contents
1. Instructions for Use......................................................................1
1.1 Standing Position, Posture and Face Expressions...................1
1.2 Enrollment Face Expressions ...................................................2
1.3 Finger Placement......................................................................3
1.4 Use of the Touch Screen ..........................................................4
1.5 Touch Operations......................................................................5
1.6 Appearance of Device...............................................................7
1.7 Main Interface ...........................................................................8
1.8 Verification Modes...................................................................10
1.8.1 Fingerprint Verification .....................................................10
1.8.2 Face Verification...............................................................12
1.8.3 Password Verification.......................................................13
1.8.4 ID Card Verification ★.....................................................14
1.8.5 Combination Verification ★.............................................15
2. Main Menu ...................................................................................17
3. Add User ......................................................................................19
3.1 Entering a User ID ..................................................................20
3.2 Entering a Name .....................................................................21
3. 3 Enrolling a Fingerprint............................................................22
3. 4 Enrolling a Password .............................................................24
3. 5 Enrolling a Face .....................................................................25
3.6 Entering a Group No. ..............................................................26
3.7 Modifying User Rights.............................................................28
3.8 Enroll Photos...........................................................................29
3.9 User Access Settings ..............................................................30
I
Multi-Biometric Access Control Terminal User Manual
3.10 Enrolling an ID card ★.........................................................33
4. User Management.......................................................................34
4.1 Edit a User ..............................................................................35
4.2 Delete a User ..........................................................................36
4.3 Query a User...........................................................................37
5. Communication Settings ...........................................................38
5.1 Network Settings.....................................................................39
5.2 Wiegand Output ......................................................................41
5.2.1 Wiegand 26-bits Output Description ................................42
5.2.2 Wiegand 34-bits Output Description ................................44
5.2.3 Customized Format..........................................................46
5.3 Wiegand Input.........................................................................50
6. System Configuration ................................................................51
6.1 General Parameters................................................................52
6.2 Interface Parameters ..............................................................53
6.3 Fingerprint Parameters ...........................................................54
6.4 Face Parameters ....................................................................56
6.5 Log Settings ............................................................................58
6.6 Keyboard Definitions...............................................................59
6.7 Access Settings.......................................................................60
6.7.1 Time zone setting .............................................................61
6.7.2 Holiday setting..................................................................62
6.7.3 Group time zone setting...................................................64
6.7.4 Unlock Combination Setting.............................................67
6.7.5 Access control parameter ................................................69
6.7.6 Duress Alarm Parameters ................................................71
II
Table of Contents
6.7.7 Anti-Pass back setting......................................................72
6.8 Update ....................................................................................73
7. Data Management .......................................................................74
8. Date/Time Setting .......................................................................77
8.1 Set Date/Time .........................................................................77
8.2 Bell Setting ★ ........................................................................78
9. Auto Test......................................................................................80
10. USB Disk Management ............................................................82
11. System Information ..................................................................83
12. Appendix ...................................................................................84
Appendix 1 T9 Input Instructions ..................................................84
Appendix 2 Introduction of Wiegand.............................................86
Appendix 3 Photo ID Function ......................................................88
Appendix 4 Multi-combination Authentication Mode ★ ...............89
Appendix 5 Anti-Pass Back ★ .....................................................93
Appendix 6 Statement on Human Rights and Privacy..................96
Appendix 7 Environment-Friendly Use Description ......................98
MultiBio700 User Manual
ZKTechnologyEU
1. Instructions for Use
1.1 Standing Position, Posture and Face Expressions
1. Recommended standing-distance from device:
For users 5-6 feet tall (1.5m-1.85m) we recommend
users stand about 2 feet (0.5m) from the wall.
When viewing your image on the device display window,
step away if your image appears too bright. Step closer if
your image appears too dark.
2.
Recommended
face
Expressions
vs.
poor
Expressions:
3. Recommended Posture (pose) vs. poor Posture (pose):

Note: During enrollment and verification, try to have a relaxed unstrained face
1
MultiBio700 User Manual
ZKTechnologyEU
expression and stand upright.
1.2 Enrollment Face Expressions
During the enrollment, position your head such way that your face appears in the
center of the device display window. The device will prompt you how to move your
head.
Follow the voice prompts by first gently turning your head left, then right. Then
your head gently down, then up, and so on. The slight variations of the head angles
will help the device to better recognize your face when you attempt to verify.
The enrollment face experssions as follows:
Look ahead
Look at screen
Bow down
Turn left
Turn
right
2
MultiBio700 User Manual
ZKTechnologyEU
1.3 Finger Placement
Recommended fingers: The index finger, middle finger or the ring finger is
recommended; the thumb and little finger are not recommended (because they are
usually clumsy when pressing on the fingerprint collection screen).
1. Proper finger placement:
The finger must be flat to the surface
and centered on the fingerprint
sensor.
2. Improper finger placement:
Not flat to the surface
Slanting
Off-center
Off-center
Please enroll and verify your fingerprint by using the proper finger placement
mode. We shall not be held accountable for any consequences arising out of the
degradation in verification performance due to improper user operations. We shall
reserve the right of final interpretation and revision of this document.
3
MultiBio700 User Manual
ZKTechnologyEU
1.4 Use of the Touch Screen
Touch the screen with one of your fingertips or the edge of a fingernail, as shown in
the following figure. A broad point of contact may lead to inaccurate pointing.
When the touch screen is less sensitive to the touch, you can perform a screen
calibration through the following menu operations. Press [Menu] -> [Auto Test] ->
[Calibration] on the screen and a cross icon will be displayed. After you touch the
center of the cross at five locations on the screen correctly, the system will
automatically returns to the main menu. Press [Exit] to return to the initial interface.
For details, see the description in 9. Auto Test.
Smear or dust on the touch screen may affect the performance of the touch screen.
Therefore, try to keep the screen clean and dust-free.
4
MultiBio700 User Manual
ZKTechnologyEU
1.5 Touch Operations
1. Enter numbers: Press the [User ID] key. The system will automatically display
the number input interface. After entering the user ID, press [OK] to save or press [X]
to cancel and return to the previous interface.
2. Enter Text: Press the [Name] key. The system will automatically display the text
input interface. After entering the user name, press [X] to save and return to the
previous interface.
5
MultiBio700 User Manual
ZKTechnologyEU
3. Modify parameters: Press the default value of a parameter and the system will
automatically switch to another value of this parameter.
6
MultiBio700 User Manual
ZKTechnologyEU
1.6 Appearance of Device
1. Front View
LED Indicator
Touch Screen
Touch keys
Camera
Push Buttons
Fingerprint Sensor
2. Side View
ID Card Swipe Area
Reset Button
USB Port
7
MultiBio700 User Manual
ZKTechnologyEU
1.7 Main Interface
 Date
 Screen Shortcut
 Time
 Attendance Status
 Face Image
 1:1 Switch Key
 Menu
1:1
F1
 1:1 Switch button
 Door Bell
① Date: The current date is displayed.
②Screen Shortcut Keys: Press these shortcut keys to display the attendance status.
Users can customize the function of each shortcut key. For details, see 6.6 Keyboard
Definitions.
③ Time: The current time is displayed. Both 12-hour and 24-hour time systems are
supported.
④ Attendance Status: The current attendance status is displayed.
⑤ Fingerprint Image: When the fingerprint image is displayed, the device is
8
MultiBio700 User Manual
ZKTechnologyEU
currently in the fingerprint recognition mode.
⑥ 1:1 Switch Key: By pressing this key, you can switch to the 1:1 verification
modes, and enter the digital input interface. The function is same to ⑨[1:1] Switch
Button.
⑦ Menu: You can enter the main menu by pressing this key.
⑧ Door Bell: For visitors to ring the bell and ask for help to open the door.
⑨ 1:1 Switch Button: By pressing this button, you can enter the digital input
interface of the 1:1 verification mode.
9
MultiBio700 User Manual
ZKTechnologyEU
1.8 Verification Modes
1.8.1 Fingerprint Verification
1. 1: N fingerprint verification
In this fingerprint verification mode, the device
compares current fingerprint collected by the fingerprint
sensor with all fingerprint data on the device.
1. The default main interface is the fingerprint
verification mode. See the figure on the right.
2. Press your finger on the fingerprint sensor by adopting
the proper finger placement. For details, see 1.3 Finger
Placement.
3. If the verification is successful, the device will prompt
“Verified”.
4. If the verification is not successful, the device will
prompt “Please try again”.
10
MultiBio700 User Manual
ZKTechnologyEU
2. 1:1 fingerprint verification
In the 1:1 fingerprint verification mode, the device
compares current fingerprint collected through the
fingerprint sensor with that in relation to the user ID
entered through the keyboard. Adopt this mode only
when it is difficult to recognize the fingerprint.
1. Press [1:1] on the screen or [1:1] button to enter the
1:1 fingerprint recognition mode.
2. Enter user ID and then press the "Fingerprint” icon to
enter the 1:1 fingerprint recognition mode. If the prompt
“Unregistered user!” is displayed, the user ID does not
exist.
3. Press your finger on the fingerprint sensor by adopting the proper finger
placement. For details, see 1.3 Finger Placement.
4. If the verification is successful, the device will prompt “Verified”, otherwise the
device will prompt “Please try again”.
11
MultiBio700 User Manual
ZKTechnologyEU
1.8.2 Face Verification
1:1 face verification
In the 1:1 face verification mode, the device compares
current face collected through the camera with that in
relation to the user ID entered through the keyboard.
Adopt this mode only when it is difficult to recognize
the face.
1. Press [1:1] on the screen or [1:1] button to enter the
1:1 recognition mode.
2. Enter user ID and then press the "1:1 Face” icon to
enter 1:1 face recognition mode. If the prompt
“Unregistered user!” is displayed, the user ID does not
exist.
3. Compare the face in a proper way. For details, see 1.1 Standing Position, Posture
and Face Expression.
4. If the verification is successful, the device will prompt “Verified”. The system
will return to the main interface if the verification is not passed within 20 seconds.
12
MultiBio700 User Manual
ZKTechnologyEU
1.8.3 Password Verification
In the password verification mode, the device compares
the password entered with that in relation to the user ID.
1. Press [1:1] on the screen or [1:1] button to enter the
password verification mode.
2. Enter the user ID and then press the "Key” icon to
enter the password verification mode. If the prompt
“Unregistered user!” is displayed, the user ID does not
exist.
3. Enter the password and press the “OK” icon to start
the password comparison.
4. If the verification is successful, the device will prompt
“Verified”, otherwise the device will prompt “Verify fail” and return to password
input interface.
13
MultiBio700 User Manual
ZKTechnologyEU
1.8.4 ID Card Verification ★
 Note: Only the products with the built-in ID card
module support the ID card verification.
In the fingerprint verification mode, the device compares
current ID card collected by the Card Reader with all the
ID card data on the device.
1. Swipe your ID card on the card swipe area by
adopting the proper way. For the card swipe area, see 1.6
Appearance of Device.
3. If the verification is successful, the device will prompt
“Verified”.
4. If the verification is not successful, the device will prompt “Not Enrolled”.
14
MultiBio700 User Manual
ZKTechnologyEU
1.8.5 Combination Verification ★
The device supports up to 20 verification modes, including FACE&PIN/FP/RF/PW、
FP&PW、FP&RF、FACE&FP、FACE&PW、FACE&RF、FP、PW、RF、FACE&PIN、
FP/RF、PW/RF、FP/PW、PW&RF、PIN&FP、FP&PW&RF、PIN&FP&PW、
FP&RF/PIN、FACE&FP&RF、FACE&FP&PW etc. For the detail, please refer to
Appendix 4 Multi-combination Authentication Mode.
 Note: RF means ID card verification. Only the products with the built-in ID
card module support the ID card verification.
Here is the combination verification operation; we will use the FACE&FP
verification for an example.
If you verify the fingerprint first and then the face, the operations are as follows.
(1) The default main interface is the fingerprint verification mode, see the figure
below.
(2) Press your finger on the fingerprint sensor by adopting the proper finger
placement. For details, see 1.3 Finger Placement.
(3) If the verification is successful, the device will enter the 1:1 face recognition
15
MultiBio700 User Manual
ZKTechnologyEU
mode. Compare the face in a proper way. For details, see 1.1 Standing Position,
Posture and Face Expression.
(4) If the verification is successful, the device will prompt “Verified”. The system
will return to the main interface if the verification is not passed within 20 seconds.
Otherwise, the FACE&FP combination verification can perform such as FACE (1: N)
+ FP, PIN + FACE (1:1) + FP, PIN + FP (1:1) + FACE etc. The operation is similar
to the procedure introduced before.
16
MultiBio700 User Manual
ZKTechnologyEU
2. Main Menu
There are two types of rights respectively granted to two types of users: the
Ordinary users and administrators. Ordinary users are only granted the rights of
face, fingerprint, password or card verification, while administrators are granted
access to the main menu for various operations apart from having all the privileges
granted to ordinary users.
Press [Menu] on the initial interface to access the main menu, as shown in the
following figure:
The main menu includes nine sub menus:
Add User: Through this submenu, you can add a new user and input the information
on the device, including the user ID, name, fingerprint, face, card, password, rights,
group No. and user access.
User Mgt.: Through this submenu, you can browse the user information stored on
the device, including the user ID, name, fingerprint, face, card, password, rights,
group No. and user access. Here you can also add, modify or delete a user’s
17
Multi-Biometric Access Control Terminal User Manual
information.
Comm.: Through this submenu, you can set related parameters for communication
between the device and PC, including the IP address, gateway, subnet mask, baud
rate, device No. and communication password.
System: Through this submenu, you can set system-related parameters, including
the basic parameters, interface parameters, fingerprint, face and attendance
parameters, Keyboard definitions, Access settings, firmware update etc. to enable
the device to meet the user’s requirements to the greatest extent in terms of
functionality and display.
Data Mgt.: Through this submenu, you can perform management of data stored on
the device, for example, deleting the attendance records, all data, clear administrator,
restore to factory settings and query records.
Date/Time: Through this submenu, you can set the alarm time and duration, or set
the Bell.
Auto Test: This submenu enables the system to automatically test whether functions
of various modules are normal, including the screen, sensor, voice, face, keyboard,
clock tests and screen calibration.
Dn/Upload: Through this submenu, you can download user information and
attendance data stored in the device through a USB disk to related software or other
fingerprint recognition equipment.
Sys Info.: Through this submenu, you can browse the records and device
information.
Any user can access the main menu by pressing the [Menu] key if the system
does not have an administrator. After administrators are configured on the device, the
device needs to verify the administrators’ identity before granting them access to the
main menu. To ensure device security, it is recommended to set an administrator
when using the terminal initially. For detailed operations, see 3.7 Modify User Rights .
18
MultiBio700 User Manual
ZKTechnologyEU
3. Add User
Press [Add] on the [User Mgt.] interface to display the
[Add User] interface as shown below.
User ID: Enter a user ID. 1 to 9 digits user IDs are
supported by default.
Name: Enter a user name. 12 characters user names are
supported by default.
Fingerprint: Enroll a user’s fingerprint and the device
displays the number of enrolled fingerprints. A user can
enroll 10 fingerprints at maximum.
Password: Enroll a user’s password. The device supports
1-8 digit passwords by default.
Face: Enroll a user’s face.
Group No.: Set the group that the user belongs to.
Valid group No.: 1-24.
Role: Set the rights of a user. A user is set to ordinary
user by default and can also be set to administrator.
Ordinary users are only granted the rights of face,
fingerprint
or
password
verification,
while
administrators are granted access to the main menu for
various operations apart from having all the privileges
granted to ordinary users.
Photo: Enroll a user’s photo. During user verification,
the user’s photo is displayed on screen.
User Access: Set the lock control and access control parameters.
19
Multi-Biometric Access Control Terminal User Manual
3.1 Entering a User ID
The device automatically allocates an ID starting from 1
for every user in sequence. If you use the ID allocated by
the device, you may skip this section.
1. Press [User ID] on the [Add User] interface to display
the user ID management interface.
 Tip: The user ID can be modified during initial
enrollment, but once enrolled, it cannot be modified.
2. On the displayed keyboard interface, enter a user ID
and press [OK]. If the message “The user ID already
exists!” is displayed, enter another ID.
 Tip: The device supports 1 to 9 digits user IDs
by default. If you need to extend the length of current
user ID numbers, please consult our commercial
representatives or technical pre-sales.
3. After the user ID is entered, press [Save] to save the
current information and return to the previous interface.
Press [Exit] to return to the previous interface without
saving the current information.
20
MultiBio700 User Manual
ZKTechnologyEU
3.2 Entering a Name
Use T9 input method to enter the user name through the
keyboard.
1. Press [Name] on the [Add User] interface to display
the name input interface.
2. On the displayed keyboard interface, enter a user
name and press [X].
For details of operations on the keyboard interface, see
Appendix 1 T9 Input Instructions.
3. After the user name is entered, press [Save] to save
the current information and return to the previous
interface. Press [Exit] to return to the previous interface without saving the current
information.
 Tip: The device supports the 1 to 12 characters names by default.
21
Multi-Biometric Access Control Terminal User Manual
3. 3 Enrolling a Fingerprint
1. Press [Fingerprint] on the [Add User] interface to
display the [Enroll Fingerprint] interface.
2. On the displayed [Enroll Fingerprint] interface, place
your finger on the fingerprint sensor properly according
to the system prompt. For details, see 1.3 Finger
Placement.
3. Place the same finger on the fingerprint sensor for
three consecutive times correctly. If the enrollment
succeeds, the system will display a prompt message and
automatically return to the [Add User] interface. If the
enrollment fails, the system will display a prompt message and return to the [Enroll
Fingerprint] interface. In this case, you need to repeat the operations of step 2.
4. You can enroll the backup fingerprint by pressing [Fingerprint] again. A user can
enroll 10 fingerprints at maximum.
5. Press [Save] to save the current information and return to the previous interface.
Press [Exit] to return to the previous interface without saving the current
information.
22
MultiBio700 User Manual
ZKTechnologyEU
23
Multi-Biometric Access Control Terminal User Manual
3. 4 Enrolling a Password
1. Press [Password] on the [Add User] interface to
display the password management interface.
2. On the displayed keyboard interface, enter a password
and press [OK]. Re-enter the password according to the
system prompt and then press [OK].
 Tip: The device supports 1-8 digit passwords by
default.
3. After the password is entered, an interface is displayed
as shown below. Press [Save] to save the current
information and return to the previous interface. Press
[Exit] to return to the previous interface without saving the current information.
24
MultiBio700 User Manual
ZKTechnologyEU
3. 5 Enrolling a Face
1. Press [Face] on the [Add User] interface to display the
face enrollment interface.
2. On the displayed face enrollment interface, turn your
head to the left and right slightly, raise and lower your
head according to the voice prompts, so as to enroll
different parts of your face into the system to assure the
accurate
verification.
See
1.2
Enrollment
Face
Expressions.
3. If your face image is enrolled successfully, the system
will display a prompt message and automatically return
to the [Add User] interface.
4. Press [Save] to save the current information and return to the previous interface.
Press [Exit] to return to the previous interface without saving the current
information.
25
Multi-Biometric Access Control Terminal User Manual
3.6 Entering a Group No.
During face enrollment, the device automatically
allocates a group No. starting from 1 for every user in
sequence. When the number of users in Group No. 1
reaches the upper limit, the subsequent users will under
Group No. 2 automatically. Up to 100 face images can
be enrolled in Group No. 1 and only 50 face images can
be enrolled in other groups. If you use the group No.
allocated by the device, you may skip this section.
1. Press [Group No.] on the [Add User] interface to
display the group No. management interface.
2. On the displayed keyboard interface, enter your group No. and press [OK].
3. After the group No. is entered, an interface is displayed as shown below. Press
[Save] to save the current information and return to the previous interface. Press
[Exit] to return to the previous interface without saving the current information.
 Tip: A valid group No. contains 1 to 24 digits. Please remember your own
group No.
26
MultiBio700 User Manual
ZKTechnologyEU
27
Multi-Biometric Access Control Terminal User Manual
3.7 Modifying User Rights
 Note: There are two types of rights respectively granted to two types of users:
the ordinary users and administrators. Ordinary users are only granted the rights
of face, fingerprint, or password verification, while administrators are granted the
access to the main menu for various operations apart from having all the privileges
granted to ordinary users.
1. On the [Add User] interface, press [Role: User] to change the user to an
administrator.
2. After the modification is done, the interface is as shown below. Press [Save] to
save the current information and return to the previous interface; press [Exit] to
return to the previous interface without saving the current information.
28
MultiBio700 User Manual
ZKTechnologyEU
3.8 Enroll Photos
If you had enrolled your photo in the system, the system
will display your enrolled photo in addition to your ID
and name after you pass the verification.
1. Press [Photo] on the [Add User] interface to display
the photo enrollment interface.
2. On the photo enrollment interface, stand naturally in
front of the screen. For details, see 1.1 Standing Position,
Posture and Face Expression. Press [Capture] to capture
the photo.
3. After taking the photo, press [Exit] to return to the
previous interface.
4. After the photo is taken, press [Save] to save the current information and return to
the previous interface; press [Exit] to return to the previous interface without saving
the current information.
29
Multi-Biometric Access Control Terminal User Manual
3.9 User Access Settings
Press [User Access] on the [Add User] interface to display the user access settings
interface.
User Access settings are to set the user’s rights to verify and open the door, such as
the Verify Type, Time Zone and Duress FP management.
1. Verify Type:
(1) Group Verify Mode: If the user uses the group verify mode that he belong to.
(2) Individual verify mode: Select the verification mode for this user instead of the
group verify mode. That will not affect other users in this group.
 Note:
(1) Only the products with the built-in ID card module support the ID card
verification.
(2) For the verify type, please refer to Appendix 4 Multi-combination Authentication
Mode. Only some types of devices support Multi-combination authentication mode.
30
MultiBio700 User Manual
ZKTechnologyEU
2. Time Zone:
(1) Group Time Zone: If the user uses the group time zone that he belong to.
(2) Individual time zone: Select the time zone of this user instead of the group time
zone. That will not affect other users in the group.
3. Duress FP:
Enroll a new duress fingerprint or cancel an existing one.
In any situation, only if the enrolled duress fingerprint is
verified, it will trigger the duress alarm.
Duress FP management:
(1) Register Duress FP:
Press [Reg. Duress FP] on the [User Access] interface to
display the [Enroll Fingerprint] interface. On the
displayed [Enroll Fingerprint] interface, place your
finger on the fingerprint sensor properly according to the
system prompt. For details, see 1.3 Finger Placement.
31
Multi-Biometric Access Control Terminal User Manual
(2) Cancel duress FP:
Press [Can. Duress FP] on the [User Access] interface to popup the confirm message.
Select [YES] to delete the enrolled duress FP, otherwise select [NO] to cancel the
operation.
32
MultiBio700 User Manual
ZKTechnologyEU
3.10 Enrolling an ID card ★
1. Press [Card] on the [Add User] interface to display the
[Enroll Card] interface.
2. The [Punch Card!] interface pops up as shown below.
Swipe your ID card properly in the swiping area. For
details, see 1.6 Appearance of the Device.
3. If the card passes the verification, the device will
display a prompt message “Read Successfully! Card No.:
**********”, and returns to the [Add User] interface.
4. Press [Save] to save the current information and return
to the previous interface. Press [Exit] to return to the
previous interface without saving the current information.
33
MultiBio700 User Manual
ZKTechnologyEU
4. User Management
Browse the user information, including the user ID,
name, fingerprint, face, ID card, password, rights, group
No. and user access settings through this interface. To
add, edit or delete the basic information of users.
Press [User Management] on the main menu interface to
display the user management interface.
This user is an administrator.
 Note: The users are listed in alphabetical order by
last name. If you press a user name, you can access the editing interface of this user
to edit or delete the related user’s information.
34
MultiBio700 User Manual
ZKTechnologyEU
4.1 Edit a User
Press a user name from the list to enter the [User Info] interface.
The User ID cannot be modified, and the other operations are similar to those
performed in add a user. You can re-enroll your fingerprint and face image, change
your password, modify the management rights and group number.
For example: Change the user rights from Administrator to ordinary user. As shown
below.
35
Multi-Biometric Access Control Terminal User Manual
4.2 Delete a User
On the [User Info] interface, you can delete all or partial user information.
1. Press [Delete] to delete a user.
2. On the displayed interface, click [YES] to delete the current user or [NO] to return
to the previous interface.
3. On the [User Info] interface, press [Name], [Fingerprint], [Face] or [Password] to
delete the related user information and to re-enroll the new information follow the
device prompt.
36
MultiBio700 User Manual
ZKTechnologyEU
4.3 Query a User
To facilitate administrators to locate a user quickly from
a large number of enrolled users, the device enables to
query by “User ID”.
User ID Query:
1. Press [Query] on the [User Management] interface to
display the User ID query interface.
2. Enter the user ID on the displayed interface, and click
[OK] to locate the cursor on the desired user.
37
MultiBio700 User Manual
ZKTechnologyEU
5. Communication Settings
You can set related parameters for the communication between the device and PC,
including the IP address, gateway, communication mode, subnet mask, baud rate,
device ID, and communication key.
38
MultiBio700 User Manual
ZKTechnologyEU
5.1 Network Settings
When the device communicates with the PC over Ethernet, you need to check the
following settings:
IP Address: The IP address is 192.168.1.201 by default and can be changed as
required; the IP address of the device and that of the PC cannot be duplicated.
Subnet Mask: The subnet mask is 255.255.255.0 by default and can be changed as
required.
Gateway: The gateway is 0.0.0.0 by default. If the device and the PC are not located
in the same network segment, you need to set the gateway.
When the device communicates with the PC over serial ports (RS232/RS485), you
need to check the following settings:
RS232: This parameter is used to enable or disable the RS232 communication. If the
RS232 communication cables are used, set this parameter to “ON”.
RS485: This parameter is used to enable or disable the RS485 communication. If the
RS485 communication cables are used, set this parameter to “ON”.
Baud Rate: This parameter is used to set the baud rate for the communication
between the device and the PC. It includes five options: 9600, 19200, 38400, 57600,
and 115200. The higher baud rate is recommended for the RS232 communication to
achieve high speed communication, while the lower baud rate is recommended for
the RS485 communication to achieve stable low-speed communication.
Device ID: This parameter is used to set the ID of device from 1 to 254. If the
RS232/RS485 communication is adopted, you need to enter the device ID on the
software communication interface.
Comm. Key: To enhance the security of attendance data, you can set a password for
the connection between the device and PC. Once the password is set, you can
connect the PC with the device to access the attendance data only after entering the
correct password. The default password is 0 (that is, no password). Once a password
is set, you need to enter this password before connecting the PC software with the
device; otherwise, the connection is unsuccessful. 1 to 6 digits passwords are
supported.
39
Multi-Biometric Access Control Terminal User Manual
Considering the massive data including the fingerprint and face templates
stored in the device, it is recommended to transfer the data between the device
and PC over network to enhance the transfer speed.
40
MultiBio700 User Manual
ZKTechnologyEU
5.2 Wiegand Output
Wiegand Format: The system has two built-in formats
Wiegand 26-bits and Wiegand 34-bits, and also
supports the format customization function to meet
individualized requirements.
Failed ID: Refers to the value output by the system upon
verification failure. The output format is subject to the
setting of “Wiegand Format”. The default value scope
of Failed ID is 0–65535.
Site Code: The site code is used for a customized
Wiegand format. The site code is similar to the device ID,
but the site code is customizable and can be duplicated among different devices. The
default value scope of the Site Code is 0–255.
Pulse Width: Refers to the width of the Wiegand pulse in microseconds. The default
value scope of the pulse width is 1–1000.
Pulse Interval: Refers to the interval of the Wiegand pulse in microseconds. The
default value scope of the pulse width is 1–10000.
Output: Refers to the contents output upon successful verification. You can select
the “User ID” or “Card Number” as the output.
41
Multi-Biometric Access Control Terminal User Manual
5.2.1 Wiegand 26-bits Output Description
The system has a built-in Wiegand 26-bits format. Press [Wiegand Format], and
select “Standard Wiegand 26-bits”.
The composition of the Wiegand 26-bits format contains 2 parity bits and 24 bits for
output contents (“User ID” or “Card Number”). The binary code of 24-bits represent
up to 16,777,216 (0–16,777,215) different values.
1
2
Even parity
25 26
User ID/Card Number
Odd parity bit
Definition of Fields:
Field
Meaning
Even parity bit
Judged from bit 2 to bit 13. The even parity bit is 1 if the
character has an even number of 1 bit; otherwise, the even
parity bit is 0.
User
ID/
Card
Number (bit 2-bit
User ID/Card Number (Card Code, 0–16777215)
Bit 2 is the Most Significant Bit (MSB).
25)
Judged from bit 14 to bit 25. The odd parity bit is 1 if the
Odd parity bit
character has an even number of 1 bit; otherwise, the odd
parity bit is 0.
For example, for a user with the user ID of 12345, the enrolled card number is
0013378512 and the failed ID is set to 1.
1. When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
00000000000110000001110011
Even parity bit
User ID = Binary code of 12345
Odd parity bit
42
MultiBio700 User Manual
ZKTechnologyEU
2. When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
11100110000100011110100000
Even parity bit User ID = Binary code of 0013378512
Odd parity bit
3. The Wiegand output is as follows upon verification failure:
00000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
 Note: If the output contents exceed the scope allowed for the Wiegand format,
the last several bits will be adopted and first several bits are automatically discarded.
For example, the user ID 888 888 888 is 110 100 111 110 110 101 111 000 111 000
in binary format. Wiegand26 only supports 24 bits, that is, it only outputs the last 24
bits, and first 6 bits “110 100” are automatically discarded.
43
Multi-Biometric Access Control Terminal User Manual
5.2.2 Wiegand 34-bits Output Description
The system has a built-in Wiegand 34-bits format. Press [Wiegand Format], and
select “Standard Wiegand 34-bits”.
The composition of the Wiegand 34-bits format contains 2 parity bits and 32 bits for
output contents (“User ID” or “Card Number”). The binary code of 32-bits represent
up to 4,294,967,296 (0–4,294,967,295) different values.
1
2
EvenParit
33 34
User ID/Card Number
Odd parity bit
yBit
Table 2 Definition of Fields
Field
Meaning
Even parity bit
Judged from bit 2 to bit 17. The even parity bit is 1 if the
character has an even number of 1 bit; otherwise, the even
parity bit is 0.
User
ID/Card
Number (bit 2-bit
User ID/Card Number (Card Code, 0–4,294,967,295)
Bit 2 is the Most Significant Bit (MSB).
33)
Odd parity bit
Judged from bit 18 to bit 33. The odd parity bit is 1 if the
character has an even number of 1 bit; otherwise, the odd
parity bit is 0.
For example, for a user with the user ID of 123456789, the enrolled card number is
0013378512 and the failed ID is set to 1.
1. When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
0000001110101101111001101000101011
44
MultiBio700 User Manual
Even parity bit
ZKTechnologyEU
User ID = Binary code of 123456789
Odd parity bit
2. When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
0000000001100110000100011110100001
Even parity bit
User ID = Binary code of 0013378512
Odd parity bit
3. The Wiegand output is as follows upon verification failure:
0000000000000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
45
Multi-Biometric Access Control Terminal User Manual
5.2.3 Customized Format
Apart from the two built-in formats Wiegand 26-bits and Wiegand 34-bits, the
system also supports the format customization function to meet individualized
requirements.
The customized format consists of two character strings: the data bits and parity
bits. These two character strings need to be defined separately. Data bits define the
number of binary bits output by Wiegand as well as the meaning of each bit. The
data bits output by Wiegand can be a card number (C), site code (s), facility code (f),
manufacturer code (m) and parity bits (p). Parity bits define the check mode of each
bit in data bits and ensure the correctness of data bits during transfer through the
parity check. The parity bits can be set to odd check (o), even check (e) and both odd
check and even check (b). There is a one-to-one correspondence relationship
between the data bits and parity bits.
For example, the Wiegand26 can be customized as follows:
Definition of data bits: pssssssssccccccccccccccccp
Definition of parity bits: eeeeeeeeeeeeeooooooooooooo
 Note: Wiegand26 consists of 26 bits. The first bit is
the even parity bit of bits 2 to 13; the 26th bit is the odd
parity bit of bits 14 to 25; the second to the ninth bits are
the site code; the 10th to the 25th bits are the card number.
For details about the Wiegand protocol, see Appendix 3
Introduction of Wiegand.
To customize Wiegand format, proceed as follows:
(1) Select [Define Format] and the [Set] key is then
enabled.
(2) Press [Set] to display the [User Define Format]
46
MultiBio700 User Manual
ZKTechnologyEU
interface, as shown in the following figure:
(3) Click the entry box below “Card Format” to display the following interface:
Display Input
Display the Numbe
r of
Cancel Input
Backspace
Confirm Input
Clear Input
Characters used to define data bits and their meanings:
c: Indicates the card number, that is, the output contents,
it can be set to User ID/Card Number through menu
operations.
f: Indicates the facility code which is 0 by default. It is
not configurable. To modify it, please contact the
equipment supplier.
m: Indicates the manufacturer code which is 0 by default.
It is not configurable. To modify it, please contact the
equipment supplier.
p: Indicates the parity position.
s: Indicates the site code which can be set from 0 to 255
by default.
(4) Click the entry box below “Parity Format” to display the following interface:
47
Multi-Biometric Access Control Terminal User Manual
Characters used to define parity bits and their meanings:
o: Indicates the odd check, that is, there is an odd number of 1’s in the bit sequence
(including one parity bit). For example, for 1000110(0), the parity bit is 0 and there
are already three 1’s. After 0 is suffixed to 1000110, there is still an odd number of
1’s.
e: Indicates the even check, that is, there is an even number of 1’s in the bit sequence
(including one parity bit). For example, for 1000110(1), the parity bit is 1 and there
are already three 1’s. After 1 is suffixed to 1000110, there is an even number of 1’s.
b: Indicates both odd check and even check.
For example, Definitions of several universal Wiegand formats.
Wiegand34
Data bits:
pccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeooooooooooooooooo
Note: Wiegand34 consists of 34 bits. The first bit is the even parity bit of bits 2 to 17;
the 34th bit is the odd parity bit of bits 18 to 33; the second to the ninth bits are the
site code; the 10th to the 25th bits are the card number.
Wiegand37a
Data bits: pmmmmsssssssssssscccccccccccccccccccp
Parity bits: oeobeobeobeobeobeobeobeobeobeobeobeoe
Note: Wiegand37a consists of 37 bits. The first bit is the odd parity bit of bits 3, 4, 6,
7, 9, 10, 12, 13, 15, 16, 18, 19, 21, 22, 24, 25, 27, 28, 30, 31, 33, 34 and 36; the 37th
bit is the odd parity bit of bits 2, 4, 5, 7, 8, 10, 11, 13, 14, 16, 17, 19, 20, 22, 23, 25,
26, 28, 29, 31, 32, 34 and 35; bits 4, 7, 10, 13, 16, 19, 22, 25, 28, 31 and 34
participate in both odd and even parity check. Bits 2 to 5 are manufacturer code; bits
6 to 17 are the site code; bits 18 to 36 are the card number.
48
MultiBio700 User Manual
ZKTechnologyEU
Wiegand37
Data bits:
pmmmffffffffffssssssccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeooooooooooooooooooo
Note: Wiegand37 consists of 37 bits. The first bit is the even parity bit of bits 2 to 18;
the 34th bit is the odd parity bit of bits 19 to 36; the second to the fourth bits are the
manufacturer code; the 5th to the 14th bits are facilitate code; the 15th to the 20th bits
are the site code; the 21st to the 36th bits are the card number.
Wiegand50
Data bits: pssssssssssssssssccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeeeeeeeeooooooooooooooooooooooooo
Note: Wiegand50 consists of 50 bits. The first bit is the even parity bit of bits 2 to 25;
the 50th bit is the odd parity bit of bits 26 to 49; the second to the 16th bits are the site
code; the 17th to the 49th bits are the card number.
49
Multi-Biometric Access Control Terminal User Manual
5.3 Wiegand Input
Wiegand Format: The system has two built-in formats
Wiegand 26-bits and Wiegand 34-bits, and also
supports the format customization function to meet
individualized requirements. About the Wiegand format,
please refer to 5.2 Wiegand Output.
Bit counts: Wiegand data digit length.
Pulse width: Pulse width is 100 microseconds by
default, which can be adjusted from 20 to 800.
Pulse interval: It is 900 microseconds by default, which
can adjusted between 200 and 20000.
Input: Content contained in Wiegand input signal, including User ID or card
number.
50
MultiBio700 User Manual
ZKTechnologyEU
6. System Configuration
Through the [System] menu, you can set system-related parameters, including the
General, Display, Fingerprint, Face, Log settings, Shortcut Def, Access Control Set,
and Firmware Update, to enable the device to meet user requirements to the greatest
extent in terms of functionality and display.
51
Multi-Biometric Access Control Terminal User Manual
6.1 General Parameters
Keyboard Clicks: This parameter is used to set
whether to generate beep sound in response to every
keyboard touch. Select “ON” to enable the beep sound,
and select “OFF” to mute.
Voice Prompts: This parameter is used to set whether
to play voice prompts during the operation of the
device. Select “ON” to enable the voice prompt, and
select “OFF” to mute.
Volume (%): This parameter is used to adjust the
volume of voice prompts.
Lock Power Key: This parameter is used to set
whether to lock the power key. Select “ON” to disable the power key. If you select
“OFF”, and press the power key, the device will be shut down in three seconds.
52
MultiBio700 User Manual
ZKTechnologyEU
6.2 Interface Parameters
Language: This parameter is used to display the current
language used by the device. For multilingual-capable
devices, you can switch between different languages
through this parameter.
Toolbar: This parameter is used to display the style of
the shortcut keys on the initial interface. It can be set to
“Auto Hide” and “Permanent Display”. By selecting
“Auto Hide”, you can manually display or hide the
toolbar. By selecting “Permanent Display”, you can
permanently display the toolbar on the initial interface.
Sleep Time (S): This parameter is used to specify a
period after which the device is put in sleep mode if no operation within this period.
You can wake up the device from sleep by pressing any key or touching the screen.
53
Multi-Biometric Access Control Terminal User Manual
6.3 Fingerprint Parameters
1: 1 Threshold: This parameter is used to set the
threshold of matching between the current fingerprint
and the fingerprint template enrolled in the device in the
1:1 verification mode. If the similarity between the
current fingerprint and the fingerprint template enrolled
in the device is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
1: N Threshold: This parameter is used to set the
threshold of matching between the current fingerprint
and the fingerprint template enrolled in the device in the
1: N verification mode. If the similarity between the
current fingerprint and the fingerprint template enrolled in the device is larger than
this threshold, the matching is successful; otherwise, the matching is not successful.
The recommended thresholds are as follows:
(FRR)
High
(FAR)
Low
Medium Medium
Low
High
Threshold
1: N
1: 1
45
25
35
25
15
10
Algorithm Version: This parameter is used to select the fingerprint algorithm
version between 9.0 and 10.0. Please select the algorithm version with caution
because the fingerprint templates of these two algorithm versions are incompatible.
Fingerprint Image: This parameter is used to set whether to display the fingerprint
image on the screen during fingerprint enrollment or comparison. It has four options:
Show for Enroll: Display the fingerprint on the screen in enrolling process.
Show for Match: Display the fingerprint on the screen in verification process.
54
MultiBio700 User Manual
ZKTechnologyEU
Always Show: Display the fingerprint on the screen in enrolling and verifying
process.
Never Show: Never display the fingerprint on the screen in any case.
55
Multi-Biometric Access Control Terminal User Manual
6.4 Face Parameters
1: 1 Threshold: This parameter is used to set the
threshold of matching between the current face and the
face template enrolled in the device in the 1:1
verification mode. If the similarity between the current
face and the face template enrolled in the device is larger
than this threshold, the matching is successful; otherwise,
the matching is not successful. The valid value scope is
55─120. The higher the threshold, the lower the FAR
and the higher the FRR are, and vice versa.
1:1: N Threshold: This parameter is used to set the
threshold of matching between the current face and the
face template enrolled in the device in the 1: N verification mode. If the similarity
between the current face and the face template enrolled in the device is larger than
this threshold, the matching is successful; otherwise, the matching is not successful.
The valid value scope is 65─120. The higher the threshold, the lower the FAR and
the higher the FRR are, and vice versa.
The recommended thresholds are as follows:
FRR
FAR
High
Low
Medium Medium
Low
High
Threshold
1: N
1:1
90
80
80
70
75
65
Exposure: This parameter is used to set the exposure value of the camera.
Gain: This parameter is used to set the gain value of the camera.
Quality: This parameter is used to set a quality threshold for the face images
obtained. The device accepts the face images and processes them by adopting the
56
MultiBio700 User Manual
ZKTechnologyEU
face algorithm when their quality is higher than the threshold; otherwise, it filters
these face images.
 Note: Improper adjustment of the Exposure, Gain and Quality parameters may
severely affect the performance of the device. Please adjust the Exposure parameter
only under the guidance of the after-sales service personnel from our company.
57
Multi-Biometric Access Control Terminal User Manual
6.5 Log Settings
Log Alert: When the available space is insufficient to
store the specified number of attendance records, the
device will automatically generate an alarm (Value
scope: 1-99).
Dup. Punch Period (m): If a user’s attendance record
already exists and the user punches in again within the
specified period (unit: minute), the second attendance
record will not be stored (Value scope: 1-60 minutes).
58
MultiBio700 User Manual
ZKTechnologyEU
6.6 Keyboard Definitions
Define touch screen functional shortcut keys.
1. Press [Shortcut Def] to display the [Edit] interface, as shown below.
2. If you want to cancel the shortcut key, press [Status] to enter the edit interface,
select the value to “Undefined”.
3. Edit the item [Code], select [Label] (Six attendance state option). Select the state
of [Auto Switch], the interface as shown above.
4. Press [Save] to save the modification and exit.
59
Multi-Biometric Access Control Terminal User Manual
6.7 Access Settings
Access control settings are to set user’s open door time
zone, control lock and set related device parameters.
To unlock, the enrolled user must accord with the
following conditions:
1. The current unlock time should be in the effective
time of the user time zone or group zone.
2. The group where the user is must be in access control
(or in the same access control with other group, to open
the door together).
The new enrolled user is under the first group by default,
and use the No. 1 group time zone, the No. 1 access control group. The new enrolled
user is in unlocking state (if you have modified the related settings of access control,
the system will be changed with the modification).
60
MultiBio700 User Manual
ZKTechnologyEU
6.7.1 Time zone setting
Time zone is the minimum unit of access control option.
The whole system can define 50 time zones. Every time
zone consists of seven time sections (that is, one week).
Every time section is the effective time zone within 24
hours every day. Every user can set 3 time zones. It’s
“or” between the three zones. It is effective if only one is
satisfied.
Every
time
section
format
is
HH:MM-HH:MM, namely, accurate to minute.
If end time is smaller than start time (23:57- 23:56), the
whole day is forbidden. If end time is bigger than start
time (00:00- 23:59), it is effective section.
Effective time zone for user unlocking: 00:00-23:59 or end time is bigger than start
time.

Notice: System default time zone 1 as whole day open (namely, the new
enrolled user is unlocking).
61
Multi-Biometric Access Control Terminal User Manual
6.7.2 Holiday setting
Special access control time may be needed during
holidays. It is different to modify everybody’s access
control time. So a holiday access control time can be set,
which is applicable for all employees.
1. Add holiday:
(1) Enter holiday add interface, press the key to edit the
items.
(2) Press the touch screen number key to set the value,
after setting, press [OK] to save, and press [X] for exit
and return to the previous interface.
(3) Press [Save] to save the current information and
return to the previous interface; press [Exit] directly to return to the previous
interface without saving the current information.
62
MultiBio700 User Manual
ZKTechnologyEU
2. Edit holiday
Select the holiday to be edited and enter the edit
interface. The edit operation is similar to add holiday.
After editing, press [Save] to save and return to the
previous interface.
 Notice: If holiday access control time is set, user’s
open door time zone during holiday is subject to the time
zone here.
3. Delete holiday
Select the holiday to be deleted. Press [Delete] to popup
the confirm interface as follows. Select [Yes] to delete
this holiday, otherwise select [No] to cancel the
operation.
63
Multi-Biometric Access Control Terminal User Manual
6.7.3 Group time zone setting
Grouping is to manage employees in groups. Employees
in group use group time zone by default. Group
members can also set user time zone. Every group can
hold three time zones. The new enrolled user belongs to
Group 1 by default and can also be allocated to other
groups.
1. Add group time zone
(1) Enter the Add Group interface; press the key to edit
the items.
Code: Enter the number edit interface to set the value.
VerType: Select the Group Verify Type.
Holiday No.: Select if the Time zone is valid in holiday.
Time Zone: Select the Group Time Zone.
(2) After editing, press [Save] to save the current
information and return to the previous interface; press
[Exit] directly to return to the previous interface without
saving the current information.
 Note:
(1) RF means ID card verification. Only the products with the built-in ID card
module support the ID card verification.
(2)
For
Multi-combination
verification,
please
refer
to
Appendix
4
64
MultiBio700 User Manual
ZKTechnologyEU
Multi-combination Authentication Mode.
 Notice:
1. If the holiday is valid, only when there is an intersection between group zone and
holiday time zone, can the group member open the door.
2. If the holiday is invalid, the access control time of group member won’t be
affected by holiday.
2. Edit group time zone
Press the line to be edited, and enter the edit interface.
After editing, press [Save] to save the current
information and return to the previous interface; press
[Exit] directly to return to the previous interface without
saving the current information.
65
Multi-Biometric Access Control Terminal User Manual
3. Delete group time zone
Select the line to be deleted. Press [Delete] to popup the
confirm interface as follows. Select [Yes] to delete this
holiday, otherwise select [No] to cancel the operation.
66
MultiBio700 User Manual
ZKTechnologyEU
6.7.4 Unlock Combination Setting
Make various groups into different access controls to achieve multi-verification and
improve security. An access control can be made up of 5 groups at most.
1. Add Unlock Combination
(1) Enter holiday add Combination Setting interface,
press the key to edit the items.
(2) Press the touch screen number key to set the value,
after setting, press [OK] to save, and press [X] for exit
and return to the previous interface.
(3) Press [Save] to save the current information and
return to the previous interface; press [Exit] directly to
return to the previous interface without saving the
current information.
67
Multi-Biometric Access Control Terminal User Manual
2. Edit Unlock Combination
Select the line to be edited. Press the item directly to
enter the edit interface. After editing, press [Save] to
save the current information and return to the previous
interface; press [Exit] directly to return to the previous
interface without saving the current information.
3. Delete Unlock Combination
Select the line to be deleted. Press [Delete] to popup the
confirm interface as follows. Select [Yes] to delete this
holiday, otherwise select [No] to cancel the operation
68
MultiBio700 User Manual
ZKTechnologyEU
6.7.5 Access control parameter
Through the [Access] menu, you can set the parameters
of the electronic locks and related access control devices.
Lock Delay: Indicates the duration for the device to
place the electric lock in open state. (Value scope: 1-10
seconds)
Door Sensor Delay: Indicates the delay for checking the
door sensor after the door is opened. If door sensor state
is inconsistent with the normal state set by the door
sensor switch, an alarm will be triggered, and this period
of time is regarded as the “door sensor delay”. (Value
scope: 1-99 seconds)
Door Sensor Mode: Includes the None, Normally Open (NO), and Normally Closed
(NC) modes. “None” indicates that the door sensor switch is not used. “NO”
indicates that the door sensor is open in the normal state. “NC” indicates that the
door sensor is closed in the normal state.
Alarm Delay: Indicates the duration from the detection of the door sensor exception
to the generation of alarm signal. (Value scope: 1-99 seconds)
Failure Alarm Threshold: When the failed press times reach the set times, alarm
signal will come out (effective value: 1-9 times).
NC Time Zone: Set time zone for access control NC. Nobody can unlock during
this time zone.
NO Time Zone: Set time zone for access control NO. The lock is always in valid
state during this time zone.
Valid in Holiday: Define time zone for NO or NC. Whether the time zone set in
holiday time zone is valid.
69
Multi-Biometric Access Control Terminal User Manual
 Notice:
1. If the Time Zone of normally open or normally closed has been set, please switch
door sensor to no, otherwise it will produce alarm signal during Normal close Time
Zone or Normal open Time Zone.
2. If the normally open or normally closed Time Zone is not defined yet by the time,
the equipment will prompt that you to define the Time Zone, and transfer you to the
Time Zone interface to add.
70
MultiBio700 User Manual
ZKTechnologyEU
6.7.6 Duress Alarm Parameters
There are duress alarm parameters setting in the device.
When an employee comes across a duress situation, he
can use the set duress alarm mode to verify. The device
will open the door as usual, but the alarm signal will be
sent to the alarm.
1: 1 Trigger: if select “Yes”, when user use 1: 1 match
mode, alarm signal will come out. Or there is no alarm
signal.
1: N Trigger: if select “Yes”, when user use 1: N match
mode, alarm signal will come out. Or there is no alarm
signal.
Password Trigger: If select “Yes”, when a user use password verification mode,
alarm signal will come out. Or there is no alarm signal.
Alarm Delay: After duress alarm gets started, the alarm signal will not output
directly. It can be defined. After the set time period, the alarm signal will be
generated automatically (0-255 seconds).
71
Multi-Biometric Access Control Terminal User Manual
6.7.7 Anti-Pass back setting
Set the device Anti-Pass back function.
APB Direction: There are four options: None, APB-Out,
APB-In, APB-Out/In.
Device Status: There are three options: Exit Control,
Entry Control and None.
For Anti-Pass back function, please refer to Appendix 5
Anti-Pass back.
Anti-Pass back setting operation:
(1) Enter Anti-Pass back setting interface, press the key
to edit the items.
(2) Press the touch screen number key to set the value,
after setting, press [OK] to save, and press [X] for exit and return to the previous
interface.
(3) Press [Save] to save the current information and return to the previous interface;
press [Exit] directly to return to the previous interface without saving the current
information.
72
MultiBio700 User Manual
ZKTechnologyEU
6.8 Update
You can upgrade the device firmware by using the
upgrade file in the USB disk through this function.
If you need the firmware upgrade file, please contact our technical
support personnel. Generally the firmware upgrade is not recommended.
73
MultiBio700 User Manual
ZKTechnologyEU
7. Data Management
Through the [Data Mgt.]
menu, you can perform
management of data stored
on the device, for example,
delete
the
attendance
records, delete all data,
clear administrator, restore
the
device
to
factory
settings, and query user
records.
1. Delete Transactions: Delete all the attendance records.
2. Delete All Data: Delete all the information of enrolled personnel, including their
fingerprints, face images and attendance records.
3. Clear Administrator: Change all administrators to ordinary users.
4. Restore to Factory Settings: Restore all parameters on the device to factory
settings.
 Notice: The employee information and attendance records will not be deleted
during restoration to factory settings.
5. Query Record: After check-in successfully, the employee’s attendance records
are saved in the device. You can easily query these attendance records.
User ID: Enter the user ID of the employee to query. If this field is left blank, you
can query the attendance records of all the employees. If you enter a user ID, you
can query the attendance records of this employee.
Query Time Period: Select a time period to query, including the customized time
74
MultiBio700 User Manual
ZKTechnologyEU
period, yesterday, this week, last week, this month, last month, and all time periods.
Start and End: When you select a customized time period, you need to input a start
time and an end time. When you select other options for the time period, the start
and end time will be automatically adjusted to the related time.
After setting the query conditions, press [Query] and the records that meet the
specified query conditions will be displayed on screen.
Select the row where the desired record is located, you can query the detailed
information of this record.
For example, press User ID and enter the edit interface, input the ID number and
press [Query], the query result will display as below.
75
Multi-Biometric Access Control Terminal User Manual
76
MultiBio700 User Manual
ZKTechnologyEU
8. Date/Time Setting
8.1 Set Date/Time
The date and time of the device must be set accurately to
ensure the accuracy of attendance time.
1. Press [Menu] on the initial interface to display the
main menu interface.
2. Press [Time/Date] on the main menu interface to
display the time setting interface.
3. Select the desired date and time by pressing the
parameter. For the time format, there are 10 formats to
select from. Both 12-hour and 24-hour time systems are
supported.
4. Press [Save] to save the current information and
return to the previous interface. Press [Exit] to return to the previous interface
without saving the current information.
77
Multi-Biometric Access Control Terminal User Manual
8.2 Bell Setting ★
Lots of companies need to ring their bells to signal the start and end of work shifts,
and they usually manually ring their bells or use electric bells. To lower costs and
facilitate management, we integrated the time bell function into the device. You can
set the alarm time and duration for ringing the bell based on your requirements, so
that the device will automatically play the selected ring tone and triggers the relay at
the alarm time, and stop playing the ring tone after the set duration.
Press [Bell] on the [Date/Time] menu to display the bell setting interface, as shown
in figure below.
1. Add a bell
1) The displayed bell setting interface lists all the bells. Click [Add] to display the
[Add] interface.
2) On the [Add] interface, set the following parameters:
Bell Time: This parameter is used to set a time point when the device automatically
plays a bell ring tone every day.
Bell Date: This parameter is used to set which day the device automatically plays a
bell ring tone.
78
MultiBio700 User Manual
ZKTechnologyEU
Ring Tone: This parameter is used to set the bell ring tone.
Volume: This parameter is used to set the volume of ring tone.
Repeat: This parameter is used to set the alarm times.
State: This parameter is used to set whether to enable the bell.
Bell Type: You can select between internal ringing and external ringing. For internal
ringing, the ring tone is played by the loudspeaker of the device. For external ringing,
the ring tone is played by an external electric bell that is connected with the device.
2. Edit and delete a bell
Press a bell in the list on the bell setting interface to
display the [Edit] interface, with the similar operation as
“Add a bell”.
 Notice: Only some models have this function. If you need it, please contact our
business representative or technician.
79
MultiBio700 User Manual
ZKTechnologyEU
9. Auto Test
The auto test enables the system to automatically test whether functions of various
modules are normal, including the screen, sensor, voice, face, keyboard and clock
tests.
1. Test Screen: The device automatically tests the display effect of the color TFT
display by displaying full color, pure white and pure black and checks whether the
screen displays properly. You can continue the test by touching the screen or exit it
by pressing [Exit].
2. Test Fingerprint: The device automatically tests whether the fingerprint sensor
works properly by checking whether the fingerprint images are clear and acceptable.
When the user places his/her finger on the sensor, the collected fingerprint image is
displayed on the screen in real-time. Press [Exit] to exit the test.
3. Test Voice: The device automatically tests whether the voice files are complete
and the voice quality is good by playing the voice files stored in the device. You can
continue the test by touching the screen or exit it by pressing [Exit].
4. Test Face: The device automatically tests whether the camera works properly by
80
MultiBio700 User Manual
ZKTechnologyEU
checking whether the collected face images are clear and acceptable. Press [Exit] to
exit the test.
5. Test Keyboard: The device tests whether every key on the keyboard works
normally. Press any key on the [Keyboard Test] interface to check whether the
pressed key matches the key displayed on screen. The keys are dark-gray before
pressed, and turn blue after pressed. Press [Exit] to exit the test.
6. Test Time: The device tests whether its clock works properly by checking the
stopwatch of the clock. Touch the screen to start counting, and touch it again to stop
to check whether the counting is accurate. Press [Exit] to exit the test.
7. Screen Calibration:
You can perform all the menu operations by touching the screen with one of your
fingers or a touch pen. When the touch screen is less sensitive to the touch, you can
perform a screen calibration through menu operations.
The Screen Calibration Operation:
(1) Press [Menu] on the initial interface to display the
main menu interface.
(2) Press [Calibration] on the [Auto Test] interface to
display the screen calibration interface.
(3) Touch the center of the cross “+”.
(4) Repeat Step 3 following the move of the “+” icon to
different locations on the screen.
(5) Touch the center of the cross at five locations on the
screen correctly. When the message “Calibrating screen,
pls wait……” is displayed on screen, the calibration
succeeds and the system automatically returns to the
main menu. If the calibration fails, the system recalibration will start from Step 3.
81
MultiBio700 User Manual
ZKTechnologyEU
10. USB Disk Management
Through the [Dn/Upload] menu, you can download user information and attendance
data stored in a USB disk to related software or other fingerprint recognition
equipment.
1. Download Transactions: Download all the attendance data from the device to a
USB disk.
2. Download User: Download all the user information, fingerprints and face images
from the device to a USB disk.
3. Download user photos: Download the employees’ photos from the device to a
USB disk.
4. Upload User: Upload the user information, fingerprints and face images stored in
a USB disk to the device.
5. Upload User Photo: Upload the JPG documents that are named after the user IDs
and stored in a USB disk to the device, so that user photos can be displayed after the
employee passes the verification. See Appendix 3 Photo ID Function.
82
MultiBio700 User Manual
ZKTechnologyEU
11. System Information
You can check the storage status as well as version
information of the device through the [System
Information] option.
Records: The number of enrolled users, administrators
and passwords are displayed on the [Records] interface;
the total fingerprint storage capacity and occupied
capacity as well as the total attendance storage capacity
and
occupied capacity are graphically displayed
respectively.
Device: The device name, serial number, version
information, vendor and date of manufacture are displayed on the [Device] interface.
83
MultiBio700 User Manual
ZKTechnologyEU
12. Appendix
Appendix 1 T9 Input Instructions
The device supports to input
English characters, numbers
and symbols. Press related
button to input text. For
example, press [Name] to
display the text input interface,
as shown in the figure:
①Keyboard Area
②Text Display Area
③Text List Area
④Exit
⑤Delete
⑥Enter
⑦Space
⑨Character/English
⑩Upper/Lower Case
84
MultiBio700 User Manual
ZKTechnologyEU
To enter a name, proceed as follows:
1. Press [Name] on the [Add] interface, as shown in figure below.
2. Enter the letter characters, and a list of characters in relation to the letter is
presented in the text display area.
3. If the desired character is displayed in the text display area, press this character.
And this character is at the same time displayed on the [Name] button. Enter next
character by repeating Step 2.
4. After finishing the entry of name, press [X] to exit the keyboard interface and
return to the previous interface.
85
Multi-Biometric Access Control Terminal User Manual
Appendix 2 Introduction of Wiegand
Wiegand26 is an access control standard protocol established by the Access Control
Standard Subcommittee affiliated to the Security Industry Association (SIA). It is a
non-contact IC card reader interface and output protocol.
Wiegand26 defines the interface between the card reader and controller used in the
access control, security and other related industrial fields. Wiegand26 helps
standardize the work of the card reader designers and controller manufacturers. The
access control products manufactured by our company are also designed by
following this protocol.
Digital Signals
The figure below is a sequence diagram in which the card reader sends digital
signals in bit format to the access controller. In this sequence diagram, Wiegand
follows the SIA’s access control standard protocol for the 26-bit Wiegand card
reader (one pulse time ranges between 20 us and 100 us, and the pulse jump time
ranges between 200us and 20ms). Data1 and Data0 are high level (larger than Vol)
signals till the card reader prepares to send a data stream. The asynchronous
low-level pulse (smaller than Vol) generated by the card reader is sent to the access
control panel (The saw-tooth wave as shown in Figure below) through Data1 or
Data0. Data1 and Data0 pulses will neither overlap nor be generated synchronously.
The table below lists the maximum and minimum pulse width (a consecutive pulse)
and pulse jump time (time between pulses) allowed by the F series fingerprint access
control device.
86
MultiBio700 User Manual
ZKTechnologyEU
Figure: Sequence Diagram
Table: Pulse Time
Symbol
Definition
Typical Value of Reader
Tpw
Pulse Width
100 µs
Tpi
Pulse Interval
1 ms
87
Multi-Biometric Access Control Terminal User Manual
Appendix 3 Photo ID Function
The Photo ID function is used to display the photo
enrolled by a user or stored in a USB disk on the screen
in addition to such information as the user ID and name.
[Operation Steps]
1. When the photo taken by the device is used, the photo
can be displayed upon successful verification.
2. To use a photo stored in a USB disk, proceed as
follows:
1) Create a folder with the name of “photo” in the USB
disk, and store users' photos under this folder.
2) The user photos must be in JPG format and named
after their IDs. For example, for the user with the user ID of 154, the photo name
must be 154.jpg.
3) Insert the USB disk into USB slot on the device, and select USB Disk
Management -> Upload -> Upload Photos. Then user photos can be displayed upon
successful verification.
 Note:
1) The length of a user name cannot exceed 24 digits.
2) The recommended size of a user photo is less than 30 kbit.
3) The uploaded new user photo will overwrite the existing photo in related to the
user ID.
4) To download user photos, select USB Disk Management -> Download ->
Download User Photos. A folder with the name of “photo” will be automatically
created on the USB disk, and all downloaded user photos are stored under this
folder.
88
MultiBio700 User Manual
ZKTechnologyEU
Appendix 4 Multi-combination Authentication Mode ★
Besides this function only is owned by the fingerprint access control machine that
has been appointed, most of the fingerprint machines only have two ways to verify
by fingerprint and password, we provide a personal or group Multi-combination
Authentication Mode for high security Access control area, verification type main
include five elements that are User Number (PIN), Fingerprint (FP), Face (FACE),
Password (PW) and RF card (RF), which can combine into multi-combination.

Note: The RF card is used for ID card verification, the function of ID card
verification only is validity in the machine which ID card function is provided with.
These symbols illustrate what follow the table different means.
● “/” is or
●”+” follow next operation
● “&” is and
● FACE (Face)
● FP (fingerprint)
● PWD (Password)
● RF (RF card)
● PIN (user ID)
If Fingerprint, Face, Password and Card have been enrolled for the user, the
verification procedure is follow.
Type
FACE&PIN/FP/PW/RF
What you do
FACE+PIN or RF or PW or RF are verified
1) PIN++FACE(1:1)
2) FP(1:N)
3) PIN+PW+“OK”
4) RF(1:N)
FP&PW
FP + PW are verified
1) FP(1:N)+PW+“OK”
89
Multi-Biometric Access Control Terminal User Manual
2) PIN+FP(1:1)+PW+“OK”
3) PIN+PW+“OK”+FP
FP&RF
FP + RF are verified
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)+RF
FACE&FP
FACE + FP are verified
1) FP(1:N)+FACE
2) FACE(1:N)+FP
3) PIN+FACE(1:1)+FP
4) PIN+FP(1:1)+FACE
FACE&PW
FACE + PW are verified
1) FACE(1:N)+PW+“OK”
2) PIN+FACE(1:1)+PW
3) PIN+PW+FACE
FACE&RF
FACE + RF are verified
1) FACE(1:N)+RF
2) PIN+FACE(1:1)+RF
3) RF(1:N)+FACE
FP
Only FP is verified.
1) PIN+FP(1:1)
2) FP(1:N)
PW
Only PW is verified
PIN+PW+“OK”
RF
Only RF is verified
RF(1:N)
FACE&PIN
FACE + PIN are verified
PIN+FACE(1:1)
90
MultiBio700 User Manual
FP/RF
ZKTechnologyEU
FP or RF is verified
1) PIN+FP(1:1)
2) RF(1:N)
3) FP(1:N)
PW/RF
FP or RF is verified
1) PIN+PW+“OK”
2) RF(1:N)
FP/PW
FP or PW is verified
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+PW+“OK”
PIN&FP
PIN + FP are verified
PIN+FP(1:1)
FP&PW&RF
FP + PW + RF are verified
1) FP(1:N)+PW+“OK”+RF
2) PIN+FP(1:1)+PW+“OK”+RF
3) RF(1:N)+PW+“OK”+FP
4) PIN+ PW+“OK”+FP(1:1)+RF
PIN&FP& PW
PIN + FP + PW are verified
1) PIN+PW+“OK”+FP(1:1)
2) PIN+FP(1:1)+PW+“OK”
FP & RF/PIN
FP + PIN, or FP + RF are verified
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)
FACE&FP&RF
FACE + FP + RF are verified
1) FACE(1:N)+FP+RF
2) FP+FACE(1:1)+RF
91
Multi-Biometric Access Control Terminal User Manual
3) RF(1:N)+FACE+FP
4) PIN+FP(1:1)+FACE+RF
5) PIN+FACE(1:1)+FP+RF
FACE&FP&PW
FACE + FP + PW are verified
1) FACE(1:N) +PW+“OK”+FP
2) FP+PW+“OK”+FACE(1:1)
3) PIN+FP(1:1) +PW+“OK”+FACE
4) PIN+FACE(1:1) +PW+“OK”+FP
5) PIN+PW+“OK”+FP+FACE
 Note: For combined verification, it is better to enroll all the elements in need
for using verification mode, or verification will fail.
For example: User “A” use fingerprint for enrollment, while password is used for
verification, then the user cannot pass the verification.
92
MultiBio700 User Manual
ZKTechnologyEU
Appendix 5 Anti-Pass Back ★
【overview】
Sometimes, some illegal people follow the other one into the gate, which will cause
the security problems. To prevent such risks, this function is enabled. The In record
must match the Out record, or the gate won’t open.
This function needs two machines to work together. One is installed inside of the
door (master machine hereinafter), the other is installed outside of the door (slave
machine hereinafter). Wiegand signal communication is adopted between the two
machines.
【Working principle】
The master machine has Wiegand In and slave machine has Wiegand Out functions.
Connect Wigand Out of slave machine to Wiegand In of master machine. Wiegand
output from slave machine must not own machine ID. The number sent to master
machine from slave machine must be found in the master machine.
【Function】
Judge whether it is anti-pass back according to user’s recent in-out record. In record
and out record must be matched. This machine supports out, in, or out-in anti-pass
back.
93
Multi-Biometric Access Control Terminal User Manual
When the master machine is set as “out anti-pass back”, if user wants to come in and
go out normally, his recent record must be “in”, or he cannot go out. Any “out”
attempt will be refused by “anti-pass back” function. For example, a user’s recent
record is “in”, his second record can be “out” or “in”. His third record is based on
his second record. Out record and in record must match.(Notice: If customer has no
record before, then he can come in but cannot go out. )
When the master machine is set as “in anti-pass back”, if the user wants to come in
and go out normally, his recent record must be “out”, or he cannot go out. Any out
record will be “anti-pass back refused” by the system. (Notice: If the customer has
no former record, then he can go out, but cannot come in).
When the master machine is set as “out-in anti-pass back”, if the user wants to come
in and go out normally, if his recent record is “out” and “in”, then his next record
must be “in” and “out”.
【operation】
1. Select model
Master machine: The machine with Wiegand in function, except for F10 reader.
Slave machine: The machine with Wiegand Out function.
2. Menu setting
Anti-pass back
There are four options: in/out anti-pass back, out anti-pass back, in anti-pass back,
and none.
Out anti-pass back: Only user’s last record is in-record, can the door be open.
In anti-pass back: Only user’s last record is out-record, can the door be open.
Device status: There are three options: Control-in, control-out and none
Control-in: When it is set, the verified records on the device are in-records.
Control-out: When it is set, the verified records on the device are out-records.
None: When it is set, close the device’s anti-pass back function.
3. Modify device’s Wiegand output format
When the two devices are communicating, only the Wiegand signals without device
94
MultiBio700 User Manual
ZKTechnologyEU
ID are received. Enter device menu-> communication option-> Wiegand option
or enter software -> basic setting -> device management -> Wiegand, to modify
“defined format” as “wiegand26 without device ID”.
4. Enroll user
The user must be on master machine and slave machine at the same time, and user
PIN must be the same. Therefore, it is necessary to enroll user on master machine
and slave machine at the same time.
5. Connection instruction
Wiegand communication is adopted for master machine and slave machine. Refer to
the following for connection:
Master
Slave
IND0
<----->
WD0
IND1
<----->
WD1
GND
<----->
GND
95
Multi-Biometric Access Control Terminal User Manual
Appendix 6 Statement on Human Rights and Privacy
Dear Customers:
Thank you for choosing the hybrid biometric products designed and manufactured
by us. As a world-renowned provider of biometric technologies and services, we pay
much attention to the compliance with the laws related to human rights and privacy
in every country while constantly performing research and development.
We hereby make the following statements:
1.
All of our fingerprint recognition devices for civil use only collect the
characteristic points of fingerprints instead of the fingerprint images, and
therefore no privacy issues are involved.
2.
The characteristic points of fingerprints collected by our products cannot be
used to restore the original fingerprint images, and therefore no privacy issues
are involved.
3.
We, as the equipment provider, shall not be held legally accountable, directly or
indirectly, for any consequences arising due to the use of our products.
4.
For any dispute involving the human rights or privacy when using our products,
please contact your employer directly.
Our fingerprint products for police use, or development tools support the collection
of the original fingerprint images. As for whether such a type of fingerprint
collection constitutes an infringement of your privacy, please contact the
government or the final equipment provider. We, as the original equipment
manufacturer, shall not be held legally accountable for any infringement arising
thereof.
The law of the People’s Republic of China has the following regulations regarding
the personal freedom:
1.
Unlawful arrest, detention or search of citizens of the People's Republic of
China is prohibited; infringement of individual privacy is prohibited.
96
MultiBio700 User Manual
2.
ZKTechnologyEU
The personal dignity of citizens of the People's Republic of China is
inviolable.
3.
The home of citizens of the People's Republic of China is inviolable.
4.
The freedom and privacy of correspondence of citizens of the People's
Republic of China are protected by law.
At last we stress once again that biometrics, as an advanced recognition technology,
will be applied in a lot of sectors including e-commerce, banking, insurance and
legal affairs. Every year people around the globe suffer from great loss due to the
insecurity of passwords. The biometric products actually provide adequate
protection for your identity under a high security environment.
97
MultiBio700 User Manual
ZKTechnologyEU
Appendix 7 Environment-Friendly Use Description
The Environment Friendly Use Period (EFUP) marked on this product refers to the safety
period of time in which the product is used under the conditions specified in the product
instructions without leakage of noxious and harmful substances.
The EFUP of this product does not cover the consumable parts that need to be replaced on
a regular basis such as batteries and so on. The EFUP of batteries is 5 years.
Names and Concentration of Toxic and Hazardous Substances or Elements
Toxic and Hazardous Substances or Elements
Parts Name
Pb
Hg
Cd
Cr6+
PBB
PBDE
Chip resistor
×
○
○
○
○
○
Chip capacitor
×
○
○
○
○
○
Chip inductor
×
○
○
○
○
○
Chip diode
×
○
○
○
○
○
ESD components
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adapter
×
○
○
○
○
○
Screws
○
○
○
×
○
○
○: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for
this part is below the limit requirement in SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous
materials for this part is above the limit requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with non-hazardous environment-friendly
materials.
The
hazardous
substances
or
elements
contained
cannot
be
replaced
with
environment-friendly materials at present due to technical or economical constraints.
98
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement