PDF File Size - Haier America

PDF File Size - Haier America
Installation Instructions
HDBL865ATS
24" Built-In Dishwasher
Part # 00XXXXXXXXX
TABLE OF CONTENTS
DISHWASHER SAFETY......................................................................................... 2
INSTALLATION REQUIREMENTS.......................................................................... 3
Tools and Parts................................................................................................................ 3
Location Requirements.................................................................................................. 5
Product Dimensions....................................................................................................... 6
Drain Requirements........................................................................................................ 7
Water Supply Requirements.......................................................................................... 8
Electrical Requirements................................................................................................. 9
Wire Routing and Connection Requirements..............................................................10
INSTALLATION INSTRUCTIONS......................................................................... 11
Step 1- Unpack the Dishwasher ..................................................................................11
Step 2- Check Door Balance........................................................................................11
Step 3- Adjust Leveling Legs.......................................................................................12
Step 4- Remove Kick Plate ..........................................................................................13
Step 5- Install 90° Elbow...............................................................................................13
Step 6A- Prepare Cabinet Opening Using Existing Utility Hookups..........................14
Step 6B - Prepare Cabinet Opening Where
There are No Existing Utility Hookups.........................................................................17
Step 7- Position the Water Line and House Wiring.....................................................19
Step 8 – Insert Drain Hose Through Cabinet...............................................................20
Step 9 – Slide Dishwasher Partially Into Opening........................................................21
Step 10 – Position Dishwasher Under Countertop ....................................................21
Step 11 - Level the Dishwasher...................................................................................22
Step 12 - Connect Power Supply ................................................................................23
Step 13 - Connect to Water Supply.............................................................................26
Step 14 - Connect to Drain...........................................................................................27
Step 15 - Secure Dishwasher.......................................................................................28
Step 16 - Pre-Test Checklist.........................................................................................30
Step 17 - Test Dishwasher...........................................................................................31
Step 18 – Replace the Kick Plate..................................................................................32
1
DISHWASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and
on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can
kill or hurt you and others. All safety messages will
follow the safety alert symbol and either the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
DANGER
An imminently hazardous situation. You
could be killed or seriously injured if you
don’t immediately follow instructions.
WARNING
A potentially hazardous situation
which, if not avoided, could result in
death or serious bodily injury.
CAUTION
A potentially hazardous situation
which, if not avoided, may result in
moderate or minor injury.
All safety messages will tell you what the potential hazard is, tell you
how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Failure to follow these instructions can result in serious injury or cuts.
2
YOU NEED TO:
• Slowly open dishwasher door while someone grasps the rear of the
•
•
•
dishwasher. Remove the drain hose and lower rack. Close dishwasher
door until latched.
Install this dishwasher as specified in these instructions.
Installation should be performed by a qualified service technician. The
dishwasher must be installed to meet all electrical and plumbing national
and local codes and ordinances.
The dishwasher must be installed to allow for future removal from the
enclosure if service is required.
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
PARTS SUPPLIED
2 - #8 x 5/8” Phillips flat head
wood screws
2 - Side mounting clips
Hose clamp
Drain hose
2 - Top mounting clips
PARTS NEEDED
Ferrule, compression nut
and 90° elbow with 3/8” N.P.T.
external threads on one end.
(The other end must fit your
water supply line).
Hand shut-off valve
Thread seal tape
3 UL listed wire nuts
Waste tee
(house plumbing, if applicable)
Electrical cable
(power cord, if applicable)
3
3/8” min. copper tubing
water line
Air gap for drain hose
(if required)
Strain relief
Coupler (extending drain line,
if applicable)
Hose clamps
TOOLS NEEDED
Phillips screwdriver
5/16” and 1/4” nutdriver
Level
Flashlight
6” adjustable wrench
Measuring tape
Carpenters square
Safety glasses
Bucket
Gloves
TOOLS NEEDED - NEW INSTALLATION ONLY
Tubing cutter
4
Hole saw set
Drill and bits
LOCATION REQUIREMENTS
IMPORTANT:
•
Do not run drain lines, water lines or electrical wiring where they can interfere
with or contact dishwasher motors or legs.
•
The location where the dishwasher will be installed must provide clearance
between motors and flooring. Motors should not touch the floor.
•
The opening must have a level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level dishwasher).
•
•
Do not install dishwasher over carpeted flooring.
•
The dishwasher must be installed so that the drain hose is no more than 10 ft in
length for proper drainage.
The dishwasher must be fully enclosed on the top, sides and back and must not
support any part of the enclosure.
OPENING DIMENSIONS
•
The rough cabinet opening must be at least 24” (61 cm) deep and a maximum of
35” (88.9 cm) in height, and provide easy access to water, electricity and drain.
•
Corner locations require a 2” (5.1 cm) minimum clearance between the side of
the dishwasher door and the wall or cabinet.
90°
90°
34" to 35"
(86.4 cm
to 88.9 cm)**
6"
(15.2 cm)
3"
(7.6 cm)
18"
(45.7 cm)
3"
(7.6 cm)
3"
(7.6 cm)
1¾"
(4.4 cm)
24" (61.0 cm)
*Make sure water line, wires and drain hose are within the shaded area.
**Min. to Max. distance from the underside of countertop to floor.
NOTE: ADA installation, 321/2” (82.5) cm beneath 34” (86.4 cm) high countertops
may be accomplished by adjusting the toekick and leveling legs.
5
•
There must be a minimum of 255/8” (65.1 cm) in front of dishwasher to allow door
to fully open.
a
b
255/8"
(65.1 cm)
a
Countertop
b
Dishwasher
c
Clearance for Door Opening
2" Minimum
c
PRODUCT DIMENSIONS
Side View
25⁹⁄₁₆" (65 cm)
33¾"
(85.7 cm)
6
Rear View
23⅞" (60.6 cm)
DRAIN REQUIREMENTS
•
Use the new drain hose supplied with your dishwasher. If this is not long enough,
use a new drain hose with a maximum length of 10 ft (3.05 m) that meets all
current AHAM/IAPMO test standards, is resistant to heat and detergent, use
5/8”(1.58 cm) or 7/8”(2.2 cm) inside diameter (I.D.) hose and a coupler to connect
the two hose ends. Secure the connection with two clamps.
•
Dishwasher must be connected to waste line with an air gap (not supplied) or
32”(81.3 cm) minimum high drain loop, depending on local codes and ordinances
to prevent backflow into the dishwasher.
IMPORTANT: Failure to provide the proper drain connection height with air gap
or 32” (81.3 cm) minimum high drain loop will result in improper draining of the
dishwasher.
•
An air gap must be used if the waste tee or garbage disposal connection is less
than 20” (50.8 cm) above the floor to avoid backflow.
a
a
Air Gap
•
•
Use 1/2” minimum I.D. drain line fittings.
Do not connect drain lines from other devices to the dishwasher drain hose.
7
WATER SUPPLY REQUIREMENTS
•
The pressure of the water coming from the hot water supply line must be 20120 psi (138-862 kPa). The supply line may enter either from the right or left
side, the rear or the floor within the shaded area.
•
The water connection is located on the left front side of the dishwasher. Install
the hot water inlet line, using a 3/8” min. copper tubing water line. Route the line
as shown and extend it forward at least 24” (61 cm) from the rear wall.
NOTE: Routing the water line through the left side of cabinet opening will make
water connection easier.
b
cd
a
4" (10.2 cm)
from cabinet
24" (61 cm)
from wall
a
Hot Water Supply
b
Shutoff Valve
c
11/2" (3.8 cm) Dia. Hole
d
Hot Water Line
e
Cabinet Face
3" (7.6 cm)
from floor
The hot water line may either pass through the same hole as the electrical cable
and drain hose, or cut an additional 1½” (3.8 cm) dia. hole for the water line.
e
•
•
If the electrical cord has a three prong grounded plug, it cannot pass through the
same hole as the hot water line and drain hose. You must cut a separate hole for
the electrical cord.
•
Adjust the water heater to a water temperature of 120°F to 150°F (49°C to
65.5°C).
8
ELECTRICAL REQUIREMENTS
WARNING
Electrical Shock Hazard
Installation and service must be performed by a qualified installer or
service agency.
Always disconnect the power before servicing this unit.
This appliance must be properly grounded.
Failure to do so could result in death, fire, or electrical shock.
IMPORTANT:
•
The dishwasher must be supplied with 120 volt, 60 Hz, AC-only, 15 or 20 amp.,
fused electrical supply.
•
•
Wiring must be 2-wire with ground.
•
Contact a qualified electrician. Be sure that the electrical connection and wire
size are adequate and in conformance with the National Electrical Code, ANSI/
NFPA No. 70-latest edition and all local codes and ordinances.
If the electrical supply does not meet the above requirements, call a licensed,
qualified electrician before proceeding.
A copy of the above code standards can be obtained from the website
www.nfpa.org or:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
Grounding Instructions:
•
The dishwasher must be connected to a grounded metal, permanent wiring
system, or an equipment grounding conductor must be run with the circuit
conductors and be connected to the equipment grounding terminal or lead on
the dishwasher.
9
WIRE ROUTING AND CONNECTION REQUIREMENTS
Cabinet Preparation and Wire Routing
• Electrical connection is on the right front side of the dishwasher.
NOTE: Wiring the dishwasher will be easier if you route wire into the cabinet
opening from the right side.
•
The wiring may enter either from the right or left side, the rear or the floor within
the shaded area.
•
Wiring may pass through the same hole as the drain hose and hot water line or
cut an additional 1½” (3.8 cm) dia. hole to admit the electrical cable.
NOTE: The hole must be free of sharp edges. If the cabinet wall is metal, the
edge of the hole must be covered with a bushing/grommet.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
a
Terminal Box
a
•
For direct wire connections the cable must be routed as shown in the following
graphic. Cable must extend a minimum of 24” (61 cm) from the rear wall.
•
For power cord connections, have a qualified electrician install a 3 prong
grounding type receptacle. The power-supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the under counter space in which
the appliance is to be installed.
a
24" (61.0 cm)
minimum
from Wall
3" (7.6 cm)
from Cabinet
b
cd
10
a
11/2" (3.8 cm) Dia. Hole (Max.)
b
Ground
c
Black
d
White
INSTALLATION INSTRUCTIONS
STEP 1- UNPACK THE DISHWASHER
WARNING
Suffocation Hazard
To avoid danger of suffocation, keep plastic bag and other packing
material away from babies and children. Do not use this bag in cribs,
carriages and playpens. The plastic bag could block nose and mouth
and prevent breathing. This bag is not a toy.
Failure to follow these instructions can result in death or brain damage.
WARNING
Excessive Weight Hazard
Use two or more people to move and install dishwasher.
Failure to do so can result in back or other injury.
1. Remove and properly dispose of/recycle all packing material.
2. Stand dishwasher upright.
STEP 2- CHECK DOOR BALANCE
With another person holding the dishwasher to prevent it from tipping, open the
door slowly. If the door drops when released, increase the spring tension. If the door
closes when released, decrease the spring tension.
To adjust the spring tension:
1. Pull the spring adjustment pin out of the holes. Insert the pin into the next
highest or lowest hole.
2. Move the spring adjustment pins to the same holes on both the left-hand and
right-hand sides.
11
3. Retest the door, and continue moving the spring adjustment pin until the door is
balanced.
Increase
Decrease
STEP 3- ADJUST LEVELING LEGS
1. Measure the dishwasher height and the height of the opening from the
underside of countertop to floor where dishwasher will be installed (you need the
lowest point).
2. Extend the leveling legs out from the dishwasher base ¼” (6 mm) less than the
height of the opening.
a
Adjust to Installation
Height
a
12
STEP 4- REMOVE KICK PLATE
1. Using a screwdriver, remove the screws attaching the kick plate to the cabinet.
2. Lift off the kick plate.
a
a
2 Kick Plate Screws
STEP 5- INSTALL 90° ELBOW
1. Wrap the 90° elbow with thread seal tape, and then install it onto the water valve.
NOTE: To avoid damage to the water valve bracket and/or fitting, do not over
tighten the elbow.
2. Position the end of the elbow to face the bottom right of the dishwasher.
13
STEP 6A- PREPARE CABINET OPENING USING
EXISTING UTILITY HOOKUPS
•
Follow the steps in this section if you are installing the dishwasher in an existing
cabinet opening with utility hookups.
•
If you are installing the dishwasher in a cabinet opening that does not have
hookups, follow the instructions under “Prepare Cabinet Opening Where there
are No Existing Utility Hookups” in Step 6B.
1. Check that the water line reaches to the front left of opening where the water
connection will be made.
2. Check that the direct wire reaches to the front right of opening where the
electrical connection will be made.
If the water line and the direct wire reach far enough
into the opening, proceed to the next section
“Install the drain hose.” If they do not reach far
enough, follow the instructions under “Prepare
Cabinet Opening Where there are No Existing Utility
Hookups” in Step 6B.
water
line
direct
wire
6" (15.2 cm)
INSTALL THE DRAIN HOSE
IMPORTANT:
•
•
Always use a new drain hose when installing a new replacement dishwasher.
Keep the drain hose away from the floor and the edge of the hole where it passes
through the cabinet to minimize the noise caused by vibration when using the
dishwasher.
1. Connect drain hose to waste tee or garbage disposal using one of the following
methods.
•
•
•
•
Option 1 – Garbage Disposal - With Air Gap
Option 2 – No Garbage Disposal- With Air Gap
Option 3 – Garbage Disposal - No Air Gap*
Option 4 – No Garbage Disposal - No Air Gap*
*an air gap is recommended
14
Option 1 – (Garbage Disposal - With Air Gap):
1. Remove the garbage disposal knockout plug. Cut end of drain hose if needed (do
not cut ribbed section).
2. Attach drain hose to air gap with screw-type clamp. If the drain hose was cut, use
a 11/2” to 2” (3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw type clamps* to connect air
gap to garbage disposal inlet.
This connection must be before the drain trap and at least 20” (50.8 cm) above the
floor where dishwasher will be installed.
a
Drain Hose - Cut Here if
a
c
b
gf
h
Needed
b
Screw-Type Clamps
c
Air Gap
d d
Screw-Type Clamp
e
Drain Hose
e f
Rubber Hose Connector
g
Garbage Disposal Inlet
h
Drain Trap
*Parts available from local plumbing supply store.
Option 2 – (No Garbage Disposal- With Air Gap):
1. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was
cut, use a 11/2” to 2” (3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw type clamps* to connect air
gap to garbage disposal inlet.
This connection must be before the drain trap and at least 20” (50.8 cm) above the
floor where dishwasher will be installed.
a
Drain Hose - Cut Here if
a
Needed
c
b
d
f
g
e
h
b
Screw-Type Clamps
c
Air Gap
d
Screw-Type Clamp
e
Drain Hose
f
Rubber Hose Connector
g
Waste Tee
h
Drain Trap
*Parts available from local plumbing supply store.
15
Option 3 – (Garbage Disposal - No Air Gap):
1. Remove the garbage disposal knockout plug. Cut end of drain hose if needed (do
not cut ribbed section).
2. Attach drain hose to garbage disposal inlet with screw-type clamp.
3. Use a rubber hose connector* with screw-type clamps* to connect garbage
disposal inlet.
This connection must be before the drain trap and at least 20” (50.8 cm) above
the floor where dishwasher will be installed. It is recommended that the drain hose
be looped up and securely fastened to the underside of the counter. “See “Drain
Requirements.”
b a
a
Drain Hose
b
Screw-Type Clamp
c
Garbage Disposal Inlet
d
Drain Trap
c
d
*Parts available from local plumbing supply store.
Option 4 – (No Garbage Disposal - No Air Gap):
1. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to waste tee with 11/2” to 2” (3.8 to 5 cm) screw-type clamp*.
This connection must be before the drain trap and at least 20” (50.8 cm) above
the floor where dishwasher will be installed. It is recommended that the drain hose
be looped up and securely fastened to the underside of the counter. See “Drain
Requirements.”
a
a
Drain Hose - Cut Here
if Needed
b
e
c
d
*Parts available from local plumbing supply store.
16
b
Screw-Type Clamps
c
Drain Hose
d
Drain Trap
e
Waste Tee
STEP 6B - PREPARE CABINET OPENING WHERE THERE
ARE NO EXISTING UTILITY HOOKUPS
INSTALL ELECTRICAL CONNECTION
WARNING
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit breaker box
before installing dishwasher.
Failure to do so can result in death or electrical shock.
Method 1 - Direct Wire
1. Drill a 3/4” (1.9 cm) hole into the right-hand cabinet, or the right-hand side of the
back or floor of the opening. See following graphic for preferred and optional
locations.
NOTE: Wiring the dishwasher will be easier if the wire is routed into the opening
from the right-hand side.
b
a
a
Preferred Locations
b
Optional Locations
2. Remove sharp or rough edges by smoothing or covering the edges of the hole
that the wiring passes through.
Wood Cabinet - Sand edge of hole until smooth.
Metal Cabinet - Cover edge of hole with grommet (not provided).
3. Route cable from power supply through cabinet hole (cable must extend to the
right, front side of cabinet opening). Extend cable to 6” in front of unit and tape
to floor. This will prohibit cable from moving when dishwasher is moved into
cabinet opening.
17
Method 2 - Power Supply Cord
IMPORTANT: A mating 3 prong, ground-type wall receptacle is required in a cabinet
next to the dishwasher opening.
1. Drill a 11/2” (3.8 cm) hole in the cabinet rear or side. Preferred and Optional
locations are shown in the following graphic.
2. Smooth edges of hole for power cord.
Wood Cabinet - Sand edges of hole until smooth.
Metal Cabinet - Cover edges of hole with grommet (not provided).
b
a
a
Preferred Locations
b
Optional Locations
INSTALL THE WATERLINE
NOTE: Routing the water line through the left side of cabinet opening will make
water connection easier.
1. Drill a 1/2” (1.3 cm) hole in the cabinet side, rear or floor. Preferred and optional
locations are shown in the following graphic.
2. Measure to determine the overall length of copper tubing required for the water
line.
3. Attach copper tubing to the manual shutoff valve.
a
b
a
Preferred Locations
b
Optional Locations
4. Slowly feed copper tubing through hole in cabinet. Copper tubing will bend and
kink easily, so be gentle. The copper tubing should be far enough into the cabinet
opening to connect it to the dishwasher inlet on the front left of the dishwasher.
a
a
Copper Tubing
5. Slowly turn water shutoff valve to “ON” position. Flush water into a shallow pan
to get rid of particles that may clog the inlet valve.
6. Turn shutoff valve to “OFF” position.
18
INSTALL THE DRAIN HOSE
IMPORTANT: Always use a new drain hose.
1. Drill a 11/2” (3.8 cm) hole in cabinet wall or floor on the side of the opening closest
to the sink.
2. See STEP 6A “Install the Drain Hose” for instructions to connect the drain hose
to waste tee or garbage disposal using one of the following options:
•
•
•
•
Option 1 - Garbage Disposal - With Air Gap
Option 2 - No Garbage Disposal - With Air Gap
Option 3 - Garbage Disposal - No Air Gap*
Option 4 - No Garbage Disposal - No Air Gap*
*an air gap is recommended
STEP 7- POSITION THE WATER LINE AND HOUSE
WIRING
WARNING
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit breaker box
before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Confirm power is turned off at the source.
2. Turn off water supply.
19
4"
(10.2 cm)
6"
(15.2 cm)
a
a
Copper Supply Line
b
House Wiring
b
3. Place the water supply line and the house wiring on floor of the opening to avoid
interference with the base of the dishwasher and the components under the
dishwasher.
4. Tape the wire to the floor 6” (15.2 cm) in front of unit. This will keep the wire from
moving when the dishwasher is moved into cabinet opening.
STEP 8 – INSERT DRAIN HOSE THROUGH CABINET
WARNING
Excessive Weight Hazard
Use two or more people to move and install dishwasher.
Failure to do so can result in back or other injury.
1. Using two or more people, stand the dishwasher upright.
2. Grasp the sides of the dishwasher at the edges of the door panel, and place the
dishwasher in front of the opening.
3. Insert the drain hose into the hole in the cabinet wall.
a
a
Insulation Blanket
b
Water Line
c
Drain Hose (Maximum
b
Length 10 ft [3.0 m])
c
d
e
20
d
House Wiring
e
Power Cord (If Used)
STEP 9 – SLIDE DISHWASHER PARTIALLY INTO
OPENING
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Failure to follow these instructions can result in serious injury or cuts.
1. Slide dishwasher into the opening a few inches at a time.
NOTE: Do not push against the front of the panel or on the console – they will
dent.
2. Position power supply.
•
I f dishwasher has a power supply cord, insert power supply cord into the hole
cut into the cabinet.
•
I f using a direct-wire connection, check that the wiring is on the right front
side of opening.
3. Slowly move dishwasher completely into cabinet opening. As you proceed,
pull the drain hose through the opening under the sink. Stop pushing when the
dishwasher is a few inches forward of the adjacent cabinetry.
4. Make sure the drain hose is not kinked under the dishwasher and there is no
interference with the water line and wiring or any other component.
STEP 10 – POSITION DISHWASHER UNDER
COUNTERTOP
1. Push dishwasher completely into the opening so that the front corners of the
dishwasher door are flush with the cabinet doors.
NOTE: It is all right if the dishwasher fits tightly into cabinet opening. Do not remove
insulation blanket – the blanket reduces the sound travel.
Reposition dishwasher by grasping
both sides with hands.
Do not push against front door panel
with knee. Damage to the door panel
will occur.
21
STEP 11 - LEVEL THE DISHWASHER
IMPORTANT: Dishwasher must be level for proper dish rack operation and wash
performance.
1. Align front of dishwasher door panel with cabinet doors. You may need to adjust
alignment to be even with your cabinets.
NOTE: Prop up one side of frame to hold dishwasher up off floor when adjusting
front legs. With some installations, it may be easier to adjust the front leg using a
6” adjustable wrench.
2. Check that the leveling legs are firmly against the door.
3. Close and latch the door, and place level against the front panel. Check that
dishwasher is plumb. If needed, adjust leveling leg or add shims until dishwasher
is plumb.
NOTE: Shims must be securely attached to floor to prevent their movement
when the dishwasher is operated.
4. Repeat for other side of dishwasher.
5. Place level on door and rack track inside the tub as shown. Check that
dishwasher is level from side to side, and from back to front. If the dishwasher is
not level, adjust front legs up or down until dishwasher is level.
a
Level Front to Back
b
Level Side to Side
a
b
NOTE: Pull lower rack out about halfway. If the rack rolls forward or back into the
dishwasher, the dishwasher must be leveled again.
22
STEP 12 - CONNECT POWER SUPPLY
Use the power supply connection method specific to your model.
Method 1 - Direct Wire
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or
electrical shock.
IMPORTANT: Contact a qualified electrician. Be sure that the electrical connection
and wire size are adequate and in conformance with the National Electrical Code,
ANSI/NFPA No. 70-latest edition and all local codes and ordinances.
1. Confirm that power is turned off at the source.
2. Remove terminal box cover. Retain for later use.
3. Install a UL listed/CSA approved strain relief.
4. Route direct wire so that it does not touch dishwasher motor or lower part of
dishwasher tub.
5. Pull direct wire through strain relief in terminal box.
a
Strain Relief
a
23
6. Connect the wires as follows using UL listed wire nuts of the appropriate size to
connect direct wire to 16-gauge dishwasher wire.
Power supply wire:
white
black
ground wire
Terminal box wire:
white
black
ground connector
NOTES:
• Use UL listed wire nuts of the appropriate size to connect
your household wiring to 16-gauge dishwasher wiring.
•
I nsert wire ends into twist on connector. Do not pre-twist
bare wire.
•
•
Twist connector.
Gently tug on wires to be sure both wires are secured.
a
b
c
a
Ground
b
White
c
Black
7. Tighten strain relief screws to secure cord.
8. Reinstall terminal box cover with wires inside terminal box.
9. Make sure wires are not pinched by cover.
Method 2 - Power Supply Cord
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove the ground prong from the power cord plug.
Do not use an adapter.
Do not use an extension cord.
Failure to do so can result in death, fire or electrical shock.
IMPORTANT: The power cord and connections must comply with the National
Electrical Code, Section 422 and/or local codes and ordinances. Recommended cord
length is 54” min. and 64” max.
24
1. Confirm that power is turned off at the source.
2. Remove terminal box cover. Retain for later use.
3. Install a UL listed/CSA approved strain relief.
4. Route power cord so that it does not touch dishwasher motor or lower part of
dishwasher tub.
5. Pull power cord through strain relief in terminal box.
a
Strain Relief
a
6. Connect the wires as follows using UL listed wire nuts of the appropriate size to
connect power cord to 16-gauge dishwasher wire.
Power supply wire:
white
black
ground wire
Terminal box wire:
white
black
ground connector
NOTES:
• Use UL listed wire nuts of the appropriate size to connect
the power cord to 16-gauge dishwasher wiring.
•
I nsert wire ends into twist on connector. Do not pre-twist
bare wire.
•
•
Twist connector.
Gently tug on wires to be sure both wires are secured.
a
b
c
a
Ground
b
White
c
Black
7. Tighten strain relief screws to secure cord.
8. Reinstall terminal box cover with wire nuts inside terminal box.
9. Make sure wires are not pinched by cover.
25
STEP 13 - CONNECT TO WATER SUPPLY
Compression fittings:
•
•
Slide nut onto copper tubing about 1” (2.5 cm).
•
•
Put the tubing into the elbow as far as it will go.
lide ferrule onto the tubing. Do not position ferrule on the end of the
S
tubing.
lide the nut and ferrule forward and start the nut onto the elbow threads. Be
S
gentle when handling and positioning the copper tubing, it bends and kinks
easily.
a
b
c
a
Elbow
b
Ferrule
c
Compression
Fitting Nut
1. Route the water supply line so that it does not touch the dishwasher base,
frame, or motor to minimize the noise caused by vibration when using the
dishwasher.
2. With copper tubing pushed into elbow as far as it will go, use a wrench and
tighten compression fitting nut to elbow on water inlet valve. Do not use thread
seal tape with compression fittings.
3. Place paper towel under elbow. Turn on water supply and check for leaks.
26
STEP 14 - CONNECT TO DRAIN
1. Route the drain hose to avoid contact with motor, door springs, water line,
cabinet, flooring or the edge of the hole where it passes through the cabinet to
minimize the noise caused by vibration when using the dishwasher.
2. Do not remove drain loop from side of dishwasher.
3. Place pan under end of drain hose. Pan will collect water in drain hose.
a
Drain Hose
a
4. The drain hose molded end will fit 5/8” (1.6 cm), 3/4” (1.9 cm) or 1” (2.5 cm)
diameter connections on the air gap, waste tee or disposal. Cut on the marked
line as required for your installation.
a
a
3/4"
1"
a
Cutting Lines
5/8"
3/4”
5/8”
1”
(1.9
cm)
(1.6
cm)
(2.5 cm)
5. Use 5/8” or 7/8” inside diameter hose and a coupler to connect the two hose ends.
Secure the connection with hose clamps.
6. Secure the drain hose to the air gap, waste tee or garbage disposal with clamps.
NOTE: Total drain hose length must not exceed 10 ft (3.05 m), for proper drain
operation.
a
Hose Clamp
b
Coupler
a
b
a
27
STEP 15 - SECURE DISHWASHER
Depending on the material of your countertop, use either instructions to “Install to
Countertop” or “Install to Adjacent Cabinets” to secure your dishwasher.
Install to Countertop
The dishwasher must be secured to the countertop using the two mounting clips on
top of the dishwasher.
1. Insert the mounting clips into the front, top slots of the dishwasher.
NOTE: The top mounting clips have a break off point, so a section of the clip can
be removed, if necessary, to fit the depth of the cabinet.
a
a
Mounting Clips
b
Break Off Point
c
Tub Flange
b
c
2. Open the dishwasher door and remove lower dish rack.
3. Place a towel over the pump assembly and spray arm of dishwasher to keep
screws from falling into pump area during installation.
4. Check that the dishwasher is level and centered side to side in the opening.
5. Check that the tub flange aligns with the front face of the cabinet frame.
6. Using two Phillips screws (provided), fasten the two mounting clips on the top of
the dishwasher to the underside of the countertop.
NOTE: The dishwasher must be attached to the countertop to keep it from
tipping when the door is opened.
a
#8 x 5/8" Phillips
Flat-Head Screw
a
7. Open the door about 3” (7.6 cm) and check that the space between the inner
door and tub is equal on both sides.
8. If spacing is not equal, loosen the mounting clip screws and shift the tub.
Retighten bracket screws.
9. Check that the top of the door does not contact the screws, mounting clips or
countertop. If it does, the dishwasher must be lowered and leveled again. See
“Level The Dishwasher.”
10.If spacing is not equal, loosen the bracket screws and shift the tub. Retighten the
bracket screws.
28
11.Remove towel from dishwasher.
12.Reinstall the lower dish rack.
Install to Adjacent Cabinets
When countertops are granite or other materials that will not accept screws, secure
dishwasher with side mounting brackets.
1. Insert the mounting clips into the side slot of the dishwasher.
2. Open the dishwasher door, and then use a flat-blade screwdriver or prying tool
to remove hole covers (one on each side).
3. Install screws through the dishwasher side mount bracket and into the adjacent
cabinet on each side. Reinstall the hole covers.
a
a
Granite
Countertop
b
Screw
c
Hole Cover
bc
cb
4. Close dishwasher door and verify that gap between countertop and top of
dishwasher door is at least 1/2”.
1
/2”
(1.3 cm)
a
a
Countertop
b
Dishwasher
Door
b
29
STEP 16 - PRE-TEST CHECKLIST
1. Check that the power is OFF.
2. Open dishwasher and remove all foam and paper packaging. Properly dispose of/
recycle all packing material.
3. Locate User Manual in the literature package.
4. Read User Manual for operating instructions.
5. Check door opening and closing. If door does not open and close freely or tends
to fall, check spring adjustments. See “Check Door Balance.”
6. Check that wiring is secure under the dishwasher, not pinched or in contact with
door springs or other components. See “Position the Water Line and House
Wiring.”
7. Check door alignment with tub. If door hits tub, level dishwasher. See “Level the
Dishwasher.”
8. Check that the lower rack neither rolls forward nor back into the dishwasher
when pulled out about half way. If it does, adjust leveling legs. See “Level the
Dishwasher.”
9. Check door alignment with cabinet. If door hits cabinet, reposition or level the
dishwasher. See “Level the Dishwasher.”
10.Verify that the water supply and drain lines are not kinked or in contact with
other components.
11.Turn on the sink hot water faucet and verify water temperature. Incoming water
temperature must be between 120°F and 150°F (49°C and 65°C). A minimum of
120°F (49°C) temperature is required for best wash performance.
12.Add 2 quarts (1.9 L) of water to the bottom of the dishwasher to lubricate the
pump seal.
13.Turn on water supply. Check for leaks. Tighten connections if needed.
14.Remove protective film, if present, from the control panel and door.
30
STEP 17 - TEST DISHWASHER
1. Connect to power supply.
DIRECT WIRE METHOD:
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or
electrical shock.
•
Turn on power at source.
POWER SUPPLY CORD METHOD:
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove the ground prong from the power cord plug.
Do not use an adapter.
Do not use an extension cord.
Failure to do so can result in death, fire or electrical shock.
•
•
Plug into a grounded 3 prong outlet.
Make sure the power cord does not touch the dishwasher motor or the lower
part of the dishwasher tub.
2. Close door and turn on dishwasher.
31
3. Select Rinse Only cycle; and press START/CANCEL.
4. After the first 2 minutes, unlatch door, wait 5 seconds, and then open door.
Check to see that there is water in the bottom of the dishwasher tub. Check that
dishwasher is working properly.
5. Check for leaks under the dishwasher. If a leak is found, turn power supply off,
then tighten connections. Restore power after leak is corrected.
6. Check for leaks around the door. A leak around the door could be caused by
door rubbing or hitting against adjacent cabinetry. Reposition the dishwasher, if
necessary.
7. When the dishwasher is draining, check the drain lines. If leaks are found, turn
power off at the breaker and correct plumbing as necessary. Restore power after
corrections are made.
8. Open dishwasher door and make sure most of the water has drained. If not,
check that disposal plug has been removed and/or air gap is not plugged. Also
check drain line for kinking.
9. Run the dishwasher through another Rinse Only cycle and drain.
STEP 18 – REPLACE THE KICK PLATE
1. Place the kick plate against the kick plate bracket. The slots should align with the
kick plate bracket screw holes. Allow the bottom edge of the lower kick plate to
touch the floor.
2. Fasten with the two kick plate screws.
32
IMPORTANT
Do Not Return This Product To The Store
If you have a problem with this product, please contact the
“Haier Customer Satisfaction Center” at
1-877-337-3639.
DATED PROOF OF PURCHASE, MODEL #, AND SERIAL #
REQUIRED FOR WARRANTY SERVICE
Made in China
Haier America
Wayne, NJ 07470
HDBL865ATS
Issued: July 2015
Printed in China
Part # 00XXXXXXXXX
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement