Schneider Electric Wiser trådløs lækagesensor User Guide 22 Pages
Schneider Electric Wiser trådløs lækagesensor User Guide
The Schneider Electric Wiser Wireless Leakage Sensor is a reliable and easy-to-use device that can help you protect your home from water damage. It features two sensing pads that activate when water is present and sends out a loud alarm and sends a notification to your phone via the Wiser Gateway. The sensor is easy to install and can be placed on the floor in corners, within cabinets with exposed plumbing, beneath cabinets, or other fixtures.
advertisement
Wiser Wireless Leakage Sensor
Device user guide
Information about features and functionality of the devices.
02/2023
www.lk.dk
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of
Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.
Table of Contents
Safety information
.......................................................................................5
Wiser Water Leakage Sensor
...................................................................6
Pairing device manually.........................................................................7
Pairing device with auto scan.................................................................9
Changing the device icon ......................................................................9
Renaming the device ..........................................................................10
Changing the device location ...............................................................10
Checking the device history .................................................................12
Creating an automation .......................................................................13
Compliance
................................................................................................20
Compliance information for Green Premium products..................................20
DUG_Wiser wireless leakage sensor_LK-00 3
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
DUG_Wiser wireless leakage sensor_LK-00 5
6
Wiser Water Leakage Sensor
550B1021
For your safety
NOTICE
EQUIPMENT DAMAGE
• Avoid locations where the sensor may be accidentally kicked or otherwise moved. The best locations are on the floor in corners, within cabinets with exposed plumbing, beneath cabinets, or other fixtures.
• Do not locate the sensor right beneath the place where leakage is likely to happen.
• Do not locate the sensor at the area with rain, oil smoke and steam of cooking range.
• Do not install the sensor in a location with contaminated water such as oil or frozen water such as ice or snow.
• Do not completely immerse the sensor into the water.
Failure to follow these instructions can result in equipment damage.
About the device
The Wiser Water Leakage Sensor (hereinafter referred to as sensor ) has two sensing pads at the bottom of the body that activates when water is present between the pads. The pads are close to the floor surface when the sensor is placed in its operating position.
When the sensor is connected to the Wiser Gateway and detects water on the floor, the sensor sends out a sound alarm and reports the event to the app via
Wiser Gateway . The sound alarm stops when the sensor is removed from the water contact.
TIP: The water leakage sensor will sound an alarm even if it is not connected to the Wiser Gateway .
Operating elements
A. Status LED
B. Function key
C. Sensing pads
D. Battery cover screws
DUG_Wiser wireless leakage sensor_LK-00
A B
C
D
Installing the device
Refer to the installation instruction supplied with this product.
See Wiser Water Leakage Sensor .
Pairing the device
Using the Wiser app, pair your device with the Gateway/Hub to access and control the device. You can either add the device manually or do an auto-scan to pair it.
Pairing device manually
To pair the device manually:
1. On Home page, tap + .
2. Tap , select the required Wiser Hub on the slide-up menu.
3. Select an option to add the device(A):
– Add Device with Install Code
– Add Device without Install Code
Add Device
Install Code is Recommended device.
If you are unable to scan or type the install code, you can still add the device without it.
Add Device without Install Code
A
TIP: It is highly recommended to add the device with install code.
DUG_Wiser wireless leakage sensor_LK-00 7
4. To pair the device with an install code, tap Add Device with Install Code to display the slide-up menu. Select any one of the options (B):
– Scan Install Code - you can scan the device for the install code.
– Enter Install Code Manually - you can manually enter the install code from the device.
After pairing the device with install code, proceed to Step 6 .
8
B
Cancel
5. To pair the device without install code, tap Add Device without Install Code .
6. On the rear side of the sensor, short press (< 0,5 s) the function key 3 times on the device.
3× < 0,5 s
↓
The LED blinks orange.
7. In the app, select Confirm LED is Flashing Orange and tap Start
Configuration (C).
Cancel
How to pair device
Short-press function key 3 times.
1 2
3
C
DUG_Wiser wireless leakage sensor_LK-00
8. After a few seconds, a solid green LED indicates that the device has been successfully paired to the Gateway.
…
↓
9. Tap Done when the pairing is successful.
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on.
1. On the Home page, tap + .
2. Tap Auto scan > Confirm .
3. Enable permissions to Access location and Wi-Fi for scanning device and tap Start scanning .
NOTE: If you have multiple hubs, do Step 4 or proceed to Step 5.
4. Tap Select hub and select the Wiser Hub from the slide-up menu.
5. Short press the setup/reset button 3 times (< 0,5 s) and wait for a few seconds until the device search is complete.
The LED blinks orange.
TIP: If you want to pair multiple devices at once, perform step 5 on each device and wait for a few seconds for them to be detected.
6. Tap Next (A) and select Water Leakage Sensor .
Auto Scan
Available devices found
Water sensor
Next
A
7. Once the device is added successfully, tap Done .
Configuring the device
Changing the device icon
You can change the device icon using the Wiser app.
1. On the Home page, select the device for which you wish to change the icon.
2. At the top-right corner of the screen, tap .
DUG_Wiser wireless leakage sensor_LK-00 9
3. Tap edit next to the device name.
4. Tap Icon to view the menu.
5. In the slide-up menu, select any one of the following (A) to change the device icon:
– Take photo - allows you to click a photo from the mobile camera.
– Select from Icon Library - allows you to select an icon from the app library.
– Select from Album - allows you to select a photo from the mobile gallery.
Renaming the device
You can rename the device using the Wiser app.
1. On the Home page, select the device for which you wish to rename.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Name , enter the new name (A) and then tap Save .
Cancel
Rename
Save
A
Changing the device location
You can change the device location using the Wiser app.
1. On the Home page, select the device for which you wish to change the location.
10 DUG_Wiser wireless leakage sensor_LK-00
2. At the top-right corner of the screen, tap
Save
.
3. Tap edit next to the device name.
4. Tap Location .
5. Select the desired location from the list (A) and then tap Save .
Device location
Master Bedroom
Kitchen
Study Room
Kids Room
A
Removing the device
You can remove a device from the device list using the Wiser app,
To remove the device:
1. On the Home page, tap All devices > Water Leakage Sensor .
2. Tap to display more details.
3. Tap Remove and Factory Reset Device (A) and tap Confirm .
More
Water Leakage Sensor
Moment and Automation
Others
FAQ & Feedback
Add to home Screen
No updates available.
A
TIP: On the home page, you can tap and hold the Water Leakage
Sensor to remove the device.
NOTE: By removing the device, you will reset the device. If you still have a problem with the reset, then refer to
resetting the device, page 11 .
Resetting the device
You can reset the sensor to factory default manually.
To reset the sensor:
DUG_Wiser wireless leakage sensor_LK-00 11
1. Short-press the function key three times (<0.5 s) and then long-press the function key once (>10 s), the LED blinks red after 10 s, and then release the function key.
Upon successful reset of the sensor, the LED stops blinking. Then, the sensor restarts and blinks green for a few seconds.
NOTE: After reset, the LED turns off to save the battery.
3× < 0,5 s + 1 × 10 s
↓
…
↓
× 7
Using the device
On the Home page, tap All devices > Water Leakage Sensor to access the control panel.
On the Sensor control panel page, you can see the following:
• Battery level (A)
• Water leakage status (B)
• History (C)
Water Leakage Sensor
A
B
C
History
Checking the device history
You can monitor the water leakage detection by accessing the device history in the Wiser app.
To see the device history:
1. On the Home page, tap All devices > Water Leakage Sensor .
2. On the device control panel page, tap History .
12 DUG_Wiser wireless leakage sensor_LK-00
3. In the History page, you can see the date and time when the water leakage was detected.
History
2021-09-24
15:42:47
15:41:55
15:41:24
2021-09-23
21:50:17
21:49:15
21:46:02
21:45:25
21:44:28
21:43:56
Creating an automation
An automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. By using the Wiser app, you can create automations based on your needs.
1. On the Home page, tap the .
2. Go to Automation > + to create an automation.
3. Tap Edit name , enter the name of the automation (A) and tap Save .
TIP : You can choose the cover image that represents your automation by tapping .
My Automation
A
Cancel
Add Condition
DUG_Wiser wireless leakage sensor_LK-00 13
14
4. Tap Any condition is met to select any one of the condition type (B):
– All conditions are met - The automation is triggered when all the conditions are met.
– Any condition is met - The automation is triggered when at least one condition is met.
My Automation
Select Condition type
All conditions are met
Any condition is met
Cancel
B
5. Tap Add Condition to display the slide-up menu.
6. In the Add Condition menu, you can do either or all of the following options
(C):
– When weather changes - Select the various weather settings
– Schedule - Set the time and day
– When device status changes - Select the device and it’s function
NOTE: You can add one or more conditions using .
.
My Automation
Schedule
Add Condition
C
DUG_Wiser wireless leakage sensor_LK-00
7. Tap When device status changes > Water Leakage Sensor > Water detection state to select either or all of the functions to add in the automation:
– Detected - When the Sensor detects water leakage (D)
– Normal - When the Sensor goes back to its original state after the leakage was detected (E)
D
E
Normal
Water Detection State
8. Tap Add task to display the slide-up menu.
9. In the Add task menu, you can do either or all of the following options (F):
– Run the device - Select the devices that you want to trigger.
– Moment or Automation - Select the moment which you want to trigger or select the automation that you want to enable or disable.
– Send notification - Turn on notification for the automation.
– Delay - Set the delay time.
NOTE : You can add one or more actions using .
My Automation
Action
Add task
(Added 0/80)
Moment or Automation
All-Day
F
DUG_Wiser wireless leakage sensor_LK-00 15
10. Tap on Effective period to set the time range for the automation. You can select any one of the following (G):
– All-day - 24 hours
– Daytime - From sunrise to sunset
– Night - From sunset to sunrise
– Custom - User defined time period
Next
G
Repeat
11. Once all the actions and conditions are set, tap Save .
Example of an automation
This demonstration shows you how to create an automation to get notification on your app when the water leakage is detected.
1. Go to Automation > + to create an automation.
2. Tap Edit name , enter the name of the automation and tap Save .
TIP : You can choose the cover image that best represents your automation by tapping .
3. Tap Add Condition > When device status changes > Water Leakage
Sensor .
4. Tap Water detection state > Detected and tap Next .
5. Tap Add task > Send notification and select Notifications (A).
6. Tap Next .
Next
Multiple items selectable
A
16 DUG_Wiser wireless leakage sensor_LK-00
7. In the Automation Settings page, tap Save .
Save Cancel dit name
(1/10)
Action (1/80)
On
Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
Editing an automation
To edit an automation:
1. On the Automation tab, locate the automation you want to edit and tap .
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings.
TIP:
• You can add one or more actions using .
• To delete an existing condition or action, slide each item towards left and tap Delete .
Deleting an automation
To delete an automation:
1. On the Automation tab, locate the automation that you want to delete and then tap .
2. Tap Delete and tap Ok .
NOTE: After deleting an automation, the device action can no longer be triggered.
Replacing the batteries
1. Use a screwdriver to remove the six screws from the battery cover to access the batteries.
2. Make sure you replace the batteries with the correct polarity.
DUG_Wiser wireless leakage sensor_LK-00 17
3. Secure the battery cover and tighten the six screws using a screwdriver.
The LED blinks green seven times and then stops blinking.
IMPORTANT: Dispose used batteries, as per statutory regulations.
3
1
×6 ×6
×7
2
LED Indications
Pairing
User Action
Press the function key 3 times
LED Indication
LED blinks orange, once per second.
Status
Pairing mode is active for 30 seconds.
When pairing is completed, LED glows green for some time before turning Off.
Resetting
User Action
Press the function key 3 times and hold it down once for > 10 s.
LED Indication
After 10 s, the LED starts blinking red.
Status
The sensor is in reset mode. It is reset to the factory settings after 10 seconds. The sensor then restarts and the LED starts blinks green before turning Off.
Battery level
LED Indication
LED blinks orange once per minute with a beep sound.
Status
The battery is low (< 10%),
replace the battery, page 17 .
NOTE: A notification pop-up will appear on the app.
Troubleshooting
Symptom
The sensor triggers the automation/ schedule, but does not show the status on the app.
LED blinks orange with a beep sound.
Possible cause
The sensor may be undergoing an over-theair (OTA) firmware update.
The sensor battery is low or drained.
Solution
Wait for the firmware update to complete and then check that the sensor is reporting status.
NOTE: The firmware update runs in the background.
Replace the battery in the device, page 17
NOTE: A notification pop–up will appear on the app.
18 DUG_Wiser wireless leakage sensor_LK-00
Technical Data
Battery
Battery life
Nominal power
Operating frequency
Max. radio-power transmitted
IP rating
Operating temperature
Relative humidity
Sound level
Dimensions (H × W × D)
Communication protocol
3 VDC, LR03 AAA × 2
Up to 5 years (may vary based on the usage, frequency of firmware update and environment)
≤ 90 mW
2405 - 2480 MHz
≤ 9 dBm
IP44
−10 °C to 50 °C
10 % to 95 %
≥ 70 dB at 3 m distance
70.8 × 68.68 × 18.96 mm
Zigbee 3.0 certified
DUG_Wiser wireless leakage sensor_LK-00 19
Compliance
Compliance information for Green Premium products
Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product
Environmental Profile (PEP) and End-of-Life instructions (EOLI).
General information about Green Premium products
Click the link below to read about Schneider Electric’s Green Premium product strategy.
https://www.schneider-electric.com/en/work/support/green-premium/
Find compliance information for a Green Premium product
Click the link below to search for a product’s compliance information (RoHS,
REACH, PEP and EOLI).
NOTE: You will need the product reference number or product range to perform the search.
https://www.reach.schneider-electric.com/CheckProduct.aspx?cskey= ot7n66yt63o1xblflyfj
Trademarks
This guide makes reference to system and brand names that are trademarks of their relevant owners.
• Zigbee ® is a registered trademark of the Connectivity Standards Alliance.
• Apple ® and App Store ® are brand names or registered trademarks of Apple
Inc.
• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
• Wi-Fi ® is a registered trademark of Wi-Fi Alliance ® .
• Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies.
Other brands and registered trademarks are the property of their respective owners.
20 DUG_Wiser wireless leakage sensor_LK-00
Schneider Electric Danmark A/S
Lautrupvang 1, 2750 Ballerup
Danmark
+45 88 30 20 00 www.lk.dk
As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.
© 2023 – Schneider Electric . All rights reserved.
DUG_Wiser wireless leakage sensor_LK-00
Printed in:
Schneider Electric
Lautrupvang 1
2750 Ballerup
Denmark
+45 88 30 20 00
advertisement