Schneider Electric Wiser wireless dimmer User Guide
Schneider Electric Wiser wireless dimmer allows you to transform your traditional switch into a smart device. Control and dim your lights using the Wiser app or by manually operating the switch. Set schedules, create different scenes, or automate your lights to turn on/off based on your preferences or time of day. The dimmer is compatible with dimmable LEDs, ohmic, inductive, or capacitive loads.
Advertisement
Advertisement
Wiser wireless dimmer for build in (Puck)
Device User Guide
Information about features and functionality of the devices.
02/2023
www.lk.dk
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of
Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.
Table of Contents
Safety information
.......................................................................................4
Wiser wireless dimmer for build in (Puck)
...............................................5
Pairing the device with Wiser Gateway .........................................................7
Pairing device manually.........................................................................7
Pairing device with auto scan.................................................................8
Changing the device icon ......................................................................9
Renaming the device .......................................................................... 11
Changing the device location ............................................................... 11
Setting RL-LED mode .........................................................................12
Setting brightness level .......................................................................12
Toggle mode setting ............................................................................12
Manual operation ................................................................................14
Adjusting the brightness level using app ...............................................14
Setting up a schedule ..........................................................................15
Creating a moment .............................................................................16
Creating an automation .......................................................................18
Compliance
................................................................................................24
Compliance information for Green Premium products..................................24
DUG_Puck Dimmer_LK-00 3
4
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
Wiser wireless dimmer for build in (Puck)
550B1012
For your safety
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Safe electrical installation must be carried out only by skilled professionals.
Skilled professionals must prove profound knowledge in the following areas:
• Connecting to installation networks.
• Connecting several electrical devices.
• Laying electric cables.
• Safety standards, local wiring rules and regulations.
Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRIC SHOCK
• Make sure that the terminal connection area does not come in contact with the metallic parts of any device installed in the same location.
• Do not short the outputs to neutral.
Failure to follow these instructions will result in death or serious injury.
CAUTION
EQUIPMENT DAMAGE
• Always operate the product in compliance with the specified technical data.
• Never connect any mixed inductive/capacitive loads.
• Connect only dimmable loads.
• Do not connect the dimmer output to the socket outlet.
Failure to follow these instructions can result in injury or equipment damage.
DUG_Puck Dimmer_LK-00 5
6
Wiser wireless dimmer for build in (Puck)
About the device
The Wiser wireless dimmer for build in (Puck) (hereinafter referred to as Puck /
Micro Module Dimmer ) combines the advantages of smart dimmer functionality with ordinary mechanical push-button switches. It transforms a conventional switch into a connected device which can be controlled from the switch or through the Wiser app. It can switch and dim the ohmic, inductive, or capacitive loads and it is also compatible with dimmable LEDs.
IMPORTANT: Do not control any devices that depend on a permanent power supply.
Installing the device
Refer to the installation instruction supplied with this product.
See Wiser wireless dimmer for build in (Puck) .
Testing the device
Before using the Puck, manually test the Puck and make sure that it works when connected to the lighting devices.
WARNING
HAZARD OF ELECTRIC SHOCK
• Observe the regulations for working on live parts.
• Only actuate the device buttons using insulated auxiliary equipment that meets the requirements of EN 60900.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
• Short press the test button once, the connected lighting device turns On/Off.
• Press and hold the test button to adjust the dimming level of the connected lighting device.
L 1
< 1 s
> 1 s
DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
Pairing the device with Wiser Gateway
Using the Wiser app, first pair your device with the Wiser Gateway to access and control the device. You can either add the device manually or do an auto-scan to pair it.
Pairing device manually
To pair the device manually:
1. On Home page, tap + .
2. Tap and select the Wiser Hub on the slide-up menu.
3. Select an option to add the device (A):
– Add Device with Install Code
– Add Device without Install Code
Add Device
Install Code is Recommended device.
If you are unable to scan or type the install code, you can still add the device without it.
Add Device without Install Code
A
TIP: It is recommended to add the device with install code.
4. To pair the device with install code, tap Add Device with Install Code to open the slide-up menu. Select any one of the options (B):
– Scan Install Code : you can scan the device for the install code.
– Enter Install Code Manually : you can manually enter the install code from the device.
After scanning or entering the install code, proceed to Step 6 .
DUG_Puck Dimmer_LK-00
B
Cancel
5. To pair the device without install code, tap Add Device without Install Code .
7
Wiser wireless dimmer for build in (Puck)
6. Select any of the following:
– Short press the S/R (setup/reset) button 3 times (<0,5 s) on the Puck with a screwdriver.
– Short press the push button 3 times.
3 × < 0,5 s
L 1
3 × < 0,5 s
The LED blinks orange.
NOTE: If the puck is located behind the push button, the status LED is not visible.
7. In the app, select Confirm LED is flashing orange and tap Start configuration (C).
Cancel
How to Pair Device
Short-press S/R button 3 times.
1 2 x 3
C
After a few seconds, a solid green LED indicates that the device is successfully paired to the Gateway/Hub.
8
8. Once the device is added in the app, tap Done .
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on.
1. On the Home page, tap + .
2. Tap Auto scan > Confirm .
3. Enable permissions to Access location and Wi-Fi for scanning device and tap Start scanning .
NOTE: If you have multiple hubs, do Step 4 or proceed to Step 5.
4. Tap Select hub and select the from the slide-up menu.
DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
5. Short press the setup/reset button 3 times (< 0,5 s) and wait for a few seconds until the device search is complete.
The LED blinks orange.
TIP: If you want to pair multiple devices at once, perform step 5 on each device and wait for a few seconds for them to be detected.
6. Tap Next (A) and select Micromodule Dimmer .
Auto Scan
Available devices found
Micro Module
Dimmer
Next
A
7. Once the device is added successfully, tap Done .
Configuring the device
Changing the device icon
You can change the device icon using the Wiser app.
1. On the Home page, select the device for which you wish to change the icon.
.
2. At the top-right corner of the screen, tap
3. Tap edit next to the device name.
4. Tap Icon to view the menu.
DUG_Puck Dimmer_LK-00 9
Wiser wireless dimmer for build in (Puck)
5. In the slide-up menu, select any one of the following (A) to change the device icon:
– Take photo - allows you to click a photo from the mobile camera.
– Select from Icon Library - allows you to select an icon from the app library.
– Select from Album - allows you to select a photo from the mobile gallery.
Icon
Name
Location
Take photo
Select from Icon Library
Select from album
Cancel
A
10 DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
Renaming the device
You can rename the device using the Wiser app.
1. On the Home page, select the device for which you wish to rename.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Name , enter the new name (A) and then tap Save .
Icon
Name
Location
Cancel
Rename
Save
A
Changing the device location
You can change the device location using the Wiser app.
1. On the Home page, select the device for which you wish to change the location.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Location .
5. Select the desired location from the list (A) and then tap Save .
Device location
Living Room
Master Bedroom
Kitchen
Dining Room
Study Room
Kids Room
Save
A
DUG_Puck Dimmer_LK-00 11
Wiser wireless dimmer for build in (Puck)
Setting RL-LED mode
You can change the dimming mode in the app if you have problems with light flickering. By changing the dimming mode, the dimming quality is also improved.
To set the RL-LED mode:
1. On the Home page, Tap All devices > Micromodule Dimmer
2. Tap Settings .
3. Tap Dimming Mode and Select Leading Edge (RL-LED) (A) from the slideup menu.
NOTE:
• Refer to
for more information.
• Manual operation (Optional): Press the TEST button 14 times.
◦ If the status LED blinks 3 times in green, RL-LED mode is enabled.
◦ If the status LED blinks once in green, Auto mode is enabled.
Setting brightness level
If the dimmer is connected to an LED, the minimum and maximum brightness should be set to avoid flickering and switching off the LED.
To set the minimum and maximum brightness level:
1. On the Home page, Tap All devices > Micromodule Dimmer .
2. Tap Settings .
3. Tap Dimming Range then drag the sliding bar to increase or decrease the
Minimum Brightness and Maximum Brightness (A).
4. Tap Close (B).
Toggle mode setting
You can toggle between the last used brightness level or with 100% brightness level when the dimmer is turned on.
To toggle between the brightness level:
1. On the Home page, tap All devices > Micromodule Dimmer .
2. Tap Settings .
3. Tap Toggle Mode Setting and select either one of the function for default action.
– 100% (A) : to set the brightness level to 100% by default when ever the device is turned on.
– Last Level (B) : to set the previously used brightness level by default when ever the device is turned on.
12 DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
Removing the device
Using the , you can remove a device from the device list.
To remove the device:
1. On the Home page, tap All devices > Micromodule Dimmer .
2. Tap to display more details.
3. Tap Remove and Factory Reset Device (A).
More
Micro Module Dimmer
Device Information
Moment and Automation
Others
FAQ & Feedback
Add to Home Screen
No updates available.
Remove and Factory Reset Device
A
TIP: Alternatively, you can long tap on the Micromodule Dimmer on the
Home page to remove the device.
NOTE:
• Removing the device will reset the Puck. After reset the LED turns orange indicating that the Puck is ready to pair with another network.
• If there is a problem while pairing or resetting the Puck, refer to
Resetting the device manually, page 13 .
Resetting the device
You can reset the device to factory default manually.
1. Short press the Setup/Reset button 3 times (< 0.5 s) and then long press the
Setup/Reset button once (>10 s).
or
Short press the push button 3 times and then long press the push-button once for 10 s.
3 × < 0,5 s +
1 × 10 s
L 1
3 × < 0,5 s +
1 × 10 s
DUG_Puck Dimmer_LK-00 13
Wiser wireless dimmer for build in (Puck)
2. After 10 s, LED starts blinking red, then release the push-button.
NOTE: All configuration data, user data, and network data are deleted.
After which
• No connectivity to other devices or rooms.
• Memory function is active.
• Automatic load detection is active, RC mode is set.
• Dimmer settings will reset to default.
The LED stops blinking upon successful reset of the device.
The Puck restarts and blinks green for a few seconds.
Using the device
Manual operation
When the puck is connected to a mechanical push button, the connected lighting devices can be controlled manually.
• Short press the push button to turn on/off the light.
• Press and hold the push button to adjust the dimming level of the light.
< 1 s
> 1 s
Adjusting the brightness level using app
Using the , you can increase/decrease the brightness level remotely.
To increase/decrease the brightness level:
1. On the Home page, tap All devices.
2. In Micromodule Dimmer tap the power button (A) to turn on/off the device.
3. Tap for slide-up menu.
4. In the slide-up menu, drag the sliding bar (B) to increase/decrease the brightness.
5. Alternatively, you can navigate to device menu and tap on (C) to turn on/off the device. When the device is turned on, drag the sliding bar (D) up/down to increase/decrease the brightness.
14 DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
Setting up a schedule
The device can be fully controlled by schedule. Once the schedule is set, the device operates at a given time.
1. On the Home page, Tap All devices > Micromodule Dimmer .
2. Tap Schedule > Add Schedule to add a schedule.
3. In Add Schedule menu, set the time (A).
NOTE: The Schedule works according to the time zone where the device is located.
4. Tap Repeat (B) to select the days you want to set the schedule.
5. Tap Note (C), enter the note and tap Confirm .
6. Tap the toggle switch (D) to turn on the Notification for the schedule. The app will send a notification that the scheduled task is executed at the time of schedule.
7. Adjust the Brightness settings (E) through sliding bar.
Cancel Add Schedule
06
07
08
09
10
11
12
13
14
09
10
11
12
13
05
06
07
08
B
C
Repeat
Note
Save
Once
A
D
Micro Module Dimmer
50% 100%
E device is located.
8. Tap Save
DUG_Puck Dimmer_LK-00 15
Wiser wireless dimmer for build in (Puck)
Creating a moment
A Moment allows you to group multiple actions that are usually done together.
Using the Wiser app, you can create moments based on your needs.
1. On the Home page, tap .
2. Go to Moment > + to create a moment.
3. Tap Edit name (A), enter the name of the moment and tap Save .
TIP : You can choose the cover image that represents your moment by tapping .
Edit name
A
Cancel
Edit name
Add Task
Save
4. In the Action section, tap Add task (B) to open the slide-up menu.
5. In the Add task menu, you can do either or all of the following actions (C):
– Run the device - Select the devices that you want in a moment.
– Select Automation - Select the automation that you want to enable or disable.
– Delay - Set the delay time.
NOTE : You can add one or more actions using .
My settings
Show on Home Page Add task
Select Automation
Delay
B
C
16 DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
6. Tap Run the device > Micromodule Dimmer to select either or all the functions to add in the moment:
– Dimmer (D) : To turn on/off the device.
– Brightness (E) :To set the percentage of brightness required.
D
E
Dimmer
Select function Next
On
50%
7. Tap Next and once the actions are set, tap Save .
Cancel Moment settings Save
My Moment
Action
Micro Module Dimmer
Micro Module Dimmer
Dimmer:On
Show on Home Page
Editing a moment
To edit a moment:
1. On the Moment tab, locate the moment you want to edit and tap .
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings.
TIP:
• You can add one or more actions using .
• To delete an existing action, slide the each item towards left and tap
Delete .
Deleting a moment
To delete a moment:
1. On the Moment tab, locate the moment that you want to delete and then tap
.
2. Tap Delete and tap Ok .
NOTE: After deleting a moment, the device action can no longer be triggered.
DUG_Puck Dimmer_LK-00 17
Wiser wireless dimmer for build in (Puck)
Creating an automation
An automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. By using the Wiser app, you can create automations based on your needs.
1. On the Home page, tap the .
2. Go to Automation > + to create an automation.
3. Tap Edit name (A), enter the name of the automation and tap Save .
TIP : You can choose the cover image that represents your automation by tapping .
My Automation
A
Cancel
Add Condition
4. Tap Any condition is met to select any one of the condition type (B):
– All conditions are met - The automation is triggered when all the conditions are met.
– Any condition is met - The automation is triggered when at least one condition is met.
My Automation
Select Condition type
All conditions are met
Any condition is met
Cancel
B
5. Tap Add Condition to open the slide-up menu.
18 DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
6. In the Add Condition menu, you can do either or all of the following options
(C):
– When weather changes - Select the various weather settings.
– Schedule - Set the time and day.
– When device status changes - Select the device and it’s function.
NOTE: You can add one or more conditions using .
My Automation
Schedule
Add Condition
C
7. Tap When device status changes > Micro Module Dimmer and select either or both the functions:
– Dimmer - Turn the Dimmer on/off (D).
– Brightness - Adjust the brightness level (E).
Select function
Next
D
E
8. Tap Add task to open the slide-up menu.
DUG_Puck Dimmer_LK-00 19
Wiser wireless dimmer for build in (Puck)
9. In the Add task menu, you can do either or all of the following options (F):
– Run the device - Select the devices that you want to trigger.
– Moment or Automation - Select the moment which you want to trigger or select the automation that you want to enable or disable.
– Send notification - Turn on notification for the automation.
– Delay - Set the delay time.
NOTE : You can add one or more actions using .
My Automation
Action
Add task
(Added 0/80)
Moment or Automation
All-Day
F
10. Tap on Effective period to set the time range for the automation. You can select any one of the following (G):
– All-day - 24 hours
– Daytime - From sunrise to sunset
– Night - From sunset to sunrise
– Custom - User defined time period
Next
24 hours
From sunrise to sunset
G From sunset to sunrise
Custom
Repeat
City
11. Once all the actions and conditions are set, tap Save .
Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
Example of an automation
This demonstration shows you how to create an automation to turn on the dimmer at the scheduled time.
1. Go to Automation > + to create an automation.
2. Tap Edit name , enter the name of the automation and tap Save .
TIP : You can choose the cover image that best represents your automation by tapping .
20 DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
3. Tap Add Condition > Schedule .
• Tap Repeat (A), select the days you want to set the schedule and tap
Save .
• Set the time (B) at which the automation must start and tap Next .
Schedule Next
A
Repeat
04 29
05 30
06 31
B
4. Tap Add task > Run the device > Micromodule Dimmer .
5. Tap Dimmer (C) and in the slide-up menu, select On and tap Save .
6. Tap Brightness (D) and update the required brightness level and tap Save .
C
D
Dimmer
Select function Next
On
50%
7. Tap Next .
8. In the Automation Settings page, tap Save .
Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
Editing an automation
To edit an automation:
1. On the Automation tab, locate the automation you want to edit and tap .
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings.
TIP:
• You can add one or more actions using .
• To delete an existing condition or action, slide each item towards left and tap Delete .
DUG_Puck Dimmer_LK-00 21
Wiser wireless dimmer for build in (Puck)
Deleting an automation
To delete an automation:
1. On the Automation tab, locate the automation that you want to delete and then tap .
2. Tap Delete and tap Ok .
NOTE: After deleting an automation, the device action can no longer be triggered.
LED indication
Pairing the device
User Action
Short press the setup/reset button or push button 3 times.
LED Indication
LED blinks orange once per second.
Status
Pairing mode is active for 30 seconds. When pairing is completed, LED glows green for a few seconds before turning Off.
Resetting the device
User Action
Short press the setup/reset button or push button 3 times and hold it down once for > 10 s.
LED Indication
LED blinks red once per second.
Status
The device is in reset mode. The device then restarts and LED turns orange indicating that the device is ready for pairing.
Troubleshooting
Symptom
Dimming up not possible.
Switching on not possible.
Flickering at minimum brightness.
Flickering
Only slight dimming capability
The device is not ready to pair after the device is removed from the app.
Solution
• Reduce/increase load.
• Allow the Puck to cool in case of overheating.
• Change the load (if the load is incompatible with the Puck).
• Allow the Puck to cool in case of overheating.
• Reduce load.
• Change load.
• Check wiring between the push button and the Puck.
• Increase minimum brightness (if flickering still persists, install a 31LCDA load correction device).
• Change the load (if the minimum brightness is insufficient).
• Set RL LED mode (it is advised to use 10 % of nominal load to avoid overheating of the puck).
• Change load.
• Set RL LED mode (it is advised to use 10 % of nominal load to avoid overheating of the puck).
• Change dimming range.
• Set RL LED mode (it is advised to use 10 % of nominal load to avoid overheating of the puck).
• Change the load (if the load is incompatible with the Puck).
Reset to factory default settings, refer to Resetting the device manually .
22 DUG_Puck Dimmer_LK-00
Wiser wireless dimmer for build in (Puck)
Technical data
Nominal power rating for load type
LED
Incandescent lamp
Iron core transformer
Halogen lamp
5 – 100 VA
RC
5 – 20 VA RL
14 – 200 W
R
14 – 150 VA
L
14 – 150 W
R
Electronic step-down converter
C
Nominal voltage
Dimming channel
Standby
Operating Temperature
Neutral conductor
Connecting terminals
Extension connection
Length of all cable sections
Fuse protection
Operating frequency
Max. radio-frequency power transmitted
IP rating
Product dimensions (H x W x D)
Communication protocol
14 – 200 VA
C
AC 220-240 V, 50/60 Hz
1
Max. 0.4 W
0 ºC to 35 ºC
Not required
Max. 2 x 2.5 mm 2 , solid or stranded types
Max. 10 mechanical push buttons
Max. 50 m for 3-wire NYM cable
16 A circuit breaker
2405 - 2480 MHz
<10 mW
IP20
43 x 43 x 22 mm
Zigbee 3.0 certified
DUG_Puck Dimmer_LK-00 23
Compliance
Compliance information for Green Premium products
Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product
Environmental Profile (PEP) and End-of-Life instructions (EOLI).
General information about Green Premium products
Click the link below to read about Schneider Electric’s Green Premium product strategy.
https://www.schneider-electric.com/en/work/support/green-premium/
Find compliance information for a Green Premium product
Click the link below to search for a product’s compliance information (RoHS,
REACH, PEP and EOLI).
NOTE: You will need the product reference number or product range to perform the search.
https://www.reach.schneider-electric.com/CheckProduct.aspx?cskey= ot7n66yt63o1xblflyfj
Trademarks
This guide makes reference to system and brand names that are trademarks of their relevant owners.
• Zigbee ® is a registered trademark of the Connectivity Standards Alliance.
• Apple ® and App Store ® are brand names or registered trademarks of Apple
Inc.
• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
• Wi-Fi ® is a registered trademark of Wi-Fi Alliance ® .
• Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies.
Other brands and registered trademarks are the property of their respective owners.
24 DUG_Puck Dimmer_LK-00
Schneider Electric Denmark A/S
Lautrupvang 1, 2750 Ballerup
Denmark
+45 88 30 20 00 www.lk.dk
As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.
© 2023 – 2023 Schneider Electric . All rights reserved.
DUG_Puck Dimmer_LK-00
Printed in:
Schneider Electric Denmark A/S
Lautrupvang 1, 2750 Ballerup
Denmark
+45 88 30 20 00
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement