Schneider Electric ELKO SmartSensor Climate Wireless - Device User Guide 24 Pages
advertisement
SmartSensor Climate Wireless
Device User Guide
Commissioning instructions for the ELKO Smart system, devices and app.
02/2023
www.elko.no
Legal Information
The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to in this guide are the property of ELKO AS or its subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of
ELKO.
ELKO does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. ELKO products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
ELKO and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.
Table of Contents
Safety information
.......................................................................................4
SmartSensor Climate Wireless
.................................................................5
Pairing device manually.........................................................................6
Pairing device with auto scan.................................................................9
Changing the device icon ....................................................................10
Renaming the device .......................................................................... 11
Changing the device location ............................................................... 11
Checking the device history .................................................................14
Creating an automation .......................................................................15
DUG_Sensor Climate_ELKO-00 3
4
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
DUG_Sensor Climate_ELKO-00
SmartSensor Climate Wireless
EKO07219
For your safety
NOTICE
EQUIPMENT DAMAGE
Do not install the sensor in a place where there is strong sunlight or wind (for example, close to the ventilation).
Failure to follow these instructions can result in equipment damage.
About the device
The SmartSensor Climate Wireless (hereinafter referred to as Temperature/
Humidity sensor ) combines two sensors in one unit. The sensor measures temperature and humidity in the environment where the sensor is installed. When the sensor is connected to the ELKO SmartHUB , it reports the temperature and humidity data to the ELKO SmartHUB .
The sensor triggers other ELKO devices (such as turning on an air conditioner if the temperature is high or turning on an exhaust fan if the humidity is high) through automation.
Operating elements
A. Status LED
B. Function key
A B
DUG_Sensor Climate_ELKO-00 5
6
Installing the device
Refer to the installation instruction supplied with this product.
See SmartSensor Climate Wireless .
Pairing the device
Using the ELKO Smart app, pair your device with the ELKO SmartHUB to access and control the device. You can either add the device manually or do an auto-scan to pair it.
Pairing device manually
To pair the device manually:
1. On Home page, tap + .
2. Tap , select the required ELKO SmartHUB on the slide-up menu.
3. Select an option to add the device (A):
– Add Device with Install Code
– Add Device without Install Code
Add Device
Install Code is Recommended
Add Device without Install Code
A
TIP: It is highly recommended to add the device with install code.
DUG_Sensor Climate_ELKO-00
4. To pair the device with an install code, tap Add Device with Install Code to display the slide-up menu. Select any one of the options (B):
– Scan Install Code - you can scan the device for the install code.
– Enter Install Code Manually - you can manually enter the install code from the device.
After adding the device with install Code, proceed to Step 6 .
Add Device without Install Code B
5. To pair the device without install code, tap Add Device without Install Code .
6. On the rear side of the sensor, short press the function key 3 times (< 0,5 s).
DUG_Sensor Climate_ELKO-00
3× < 0,5 s
↓
The LED blinks orange.
7
7. In the app, select Confirm LED is flashing orange and tap Start configuration (C).
Cancel
How to pair device
Short-press function key 3 times.
3
C
The app displays the progress of connecting the device.
8. After a few seconds, a solid green LED indicates that the sensor is successfully paired.
…
↓
9. Tap Done when the pairing is successful..
8 DUG_Sensor Climate_ELKO-00
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on.
1. On the Home page, tap + .
2. Tap Auto scan > Confirm .
3. Enable permissions to Access location and Wi-Fi for scanning device and tap Start scanning .
NOTE: If you have multiple hubs, do Step 4 or proceed to Step 5.
4. Tap Select hub and select the ELKO SmartHUB from the slide-up menu.
5. Short press the setup/reset button 3 times (< 0,5 s) and wait for a few seconds until the device search is complete.
The LED blinks orange.
TIP: If you want to pair multiple devices at once, perform step 5 on each device and wait for a few seconds for them to be detected.
6. Tap Next (A) and select Temperature Humidity Sensor .
Auto Scan
Available devices found
Temperature
Humidity Sensor
Next
A
7. Once the device is added successfully, tap Done .
DUG_Sensor Climate_ELKO-00 9
Configuring the device
Changing the device icon
You can change the device icon using the ELKO Smart app.
1. On the Home page, select the device for which you wish to change the icon.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Icon to view the menu.
5. In the slide-up menu, select any one of the following (A) to change the device icon:
– Take photo - allows you to click a photo from the mobile camera.
– Select from Icon Library - allows you to select an icon from the app library.
– Select from Album - allows you to select a photo from the mobile gallery.
10 DUG_Sensor Climate_ELKO-00
Renaming the device
You can rename the device using the ELKO Smart app.
1. On the Home page, select the device for which you wish to rename.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Name , enter the new name (A) and then tap Save .
Rename
Save
A
Changing the device location
You can change the device location using the ELKO Smart app.
1. On the Home page, select the device for which you wish to change the location.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Location .
5. Select the desired location from the list (A) and then tap Save .
Device location
Living Room
Master Bedroom
Save
A
Dining Room
Study Room
Kids Room
DUG_Sensor Climate_ELKO-00 11
Removing the device
You can remove a device from the device list using the ELKO Smart app,
To remove the device:
1. On the Home page, tap All devices > Temperature Humidity Sensor .
2. Tap to display more details.
3. Tap Remove and Factory Reset Device (A) and tap Confirm .
More
Temperature Humidity Sensor
Moment and Automation
Others
FAQ & Feedback
Add to home Screen
No updates available
A
TIP: On the Home page, you can tap and hold the Temperature/
Humidity Sensor to remove the device.
NOTE: By removing the device, you will reset the device. If you still have a problem with the reset, then refer to
resetting the device, page 13 .
12 DUG_Sensor Climate_ELKO-00
Resetting the device
You can reset the sensor to factory default manually.
To reset the sensor:
1. Remove the sensor from the base plate by sliding it upwards.
2. Short-press the function key 3 times (<0.5 s) and then long-press the function key once (>10 s), the LED blinks red after 10 s, and then release the function key.
Upon successful reset of the sensor, the LED stops blinking. Then, the sensor restarts and blinks green for a few seconds.
NOTE: After reset, the LED turns off to save the battery.
3× < 0,5 s + 1 x 10 s
…
×7
DUG_Sensor Climate_ELKO-00 13
Using the device
On the Home page, tap All devices > Temperature Humidity Sensor to access the control panel.
On the Sensor control panel page, you can see the following:
• Battery level (A)
• The current temperature value (B)
• The current humidity value (C)
• History (D)
Temperature Humidity Sensor
A
Temperature
27.0
B
Humidity
69% C
D
History
Checking the device history
You can monitor the temperature and humidity changes by accessing the device history in the ELKO Smart app.
To see the device history:
1. On the Home page, tap All devices > Temperature Humidity Sensor .
2. On the device control panel page, tap History .
3. In the History page, you can see the temperature and humidity changes in the graph.
4. Tap Day (A) to adjust the day, week, month, or year view.
History
23-09-2021
Day
A
29.7
28.2
26.8
25.3
23.9
0
00:00
12:00 23 Sept 2021
04:00 08:00 12:00
Current Humidity: 69%
16:00
79.2
74.7
70.2
65.7
61.2
0
00:00
10:00 23 Sept 2021
04:00 08:00 12:00 16:00
14 DUG_Sensor Climate_ELKO-00
Creating an automation
An automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. By using the ELKO Smart app, you can create automations based on your needs.
1. On the Home page, tap the .
2. Go to Automation > + to create an automation.
3. Tap Edit name , enter the name of the automation (A) and tap Save .
TIP : You can choose the cover image that represents your automation by tapping .
My Automation
A
Edit name
Add Condition
4. Tap Any condition is met to select any one of the condition type (B):
– All conditions are met - The automation is triggered when all the conditions are met.
– Any condition is met - The automation is triggered when at least one condition is met.
DUG_Sensor Climate_ELKO-00
5. Tap Add Condition to display the slide-up menu.
15
16
6. In the Add Condition menu, you can do either or all of the following options
(C):
– When weather changes - Select the various weather settings.
– Schedule - Set the time and day.
– When device status changes - Select the device and it’s function.
NOTE: You can add one or more conditions using .
My Automation
Add Condition
C
7. Tap When device status changes > Temperature Humidity Sensor to select either or all of the functions to add in the automation:
– Current temperature - Set the temperature (D) and select the condition
(E).
– Current humidity - Set the humidity (F) and select the condition (G).
Current Temperature Next Current humidity Next
28.0
C
E
D
70 %
G
F
0% 100% -45 45.0
8. Tap Add task to display the slide-up menu.
DUG_Sensor Climate_ELKO-00
9. In the Add task menu, you can do either or all of the following options (H):
– Run the device - Select the devices that you want to trigger.
– Moment or Automation - Select the moment which you want to trigger or select the automation that you want to enable or disable.
– Send notification - Turn on notification for the automation.
– Delay - Set the delay time.
NOTE : You can add one or more actions using .
10. Tap on Effective period to set the time range for the automation. You can select any one of the following (I):
– All-day - 24 hours
– Daytime - From sunrise to sunset
– Night - From sunset to sunrise
– Custom - User defined time period
Next
All-day
24 hours
From sunrise to sunset
I From sunset to sunrise
Custom
Repeat
City
11. Once all the actions and conditions are set, tap Save .
Example of an automation
This demonstration shows you how to create an automation to open the shutter when the room is warm.
1. Go to Automation > + to create an automation.
2. Tap Edit name , enter the name of the automation and tap Save .
TIP : You can choose the cover image that represents your automation by tapping .
DUG_Sensor Climate_ELKO-00 17
18
3. Tap Add Condition > When device status changes > Temperature
Humidity Sensor .
4. Tap Current temperature , set the temperature and condition and tap Next .
TIP: You can set the temperature as 27 °C and the condition as > (greater than).
NOTE: The automation is triggered only if the status of the Sensor changes to a higher temperature than the set temperature. In this case, the automation is triggered when the temperature changes from 27 °C to
28 °C.
5. Tap to add another condition and tap When device status changes >
Temperature Humidity Sensor .
6. Tap Current humidity , set the humidity and condition and tap Next .
TIP: You can set the humidity as 65% and the condition as > (greater than).
NOTE: The automation is triggered only if the status of the Sensor changes to a higher humidity than the set humidity. In this case, the automation is triggered when the humidity changes from 65% to 66%.
7. Tap Add task > Run the device > Shutter .
8. Tap Control (A), select Shutter Open and tap Save .
9. Tap Percentage (B), set the shutter open percentage and tap Save .
10. Tap Next .
A
B
Open
Close
Control
80%
Cancel Cancel
11. In the Automation Settings page, tap Save .
Cancel Automation Settings
My Automation
Any condition is met
Temperature Humidity Sensor
Current Temperature:>27.0 C
Temperature Humidity Sensor
Current Humidity:>65%
Action
Shutter
Shutter
Control:Shutter Open
All-Day
Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
DUG_Sensor Climate_ELKO-00
Editing an automation
To edit an automation:
1. On the Automation tab, locate the automation you want to edit and tap .
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings.
TIP:
• You can add one or more actions using .
• To delete an existing condition or action, slide each item towards left and tap Delete .
Deleting an automation
To delete an automation:
1. On the Automation tab, locate the automation that you want to delete and then tap .
2. Tap Delete and tap Ok .
NOTE: After deleting an automation, the device action can no longer be triggered.
Replacing the batteries
To replace the batteries:
1. Remove the sensor from the base plate by sliding it upwards.
2. Unscrew the battery cover using a screwdriver.
3. Replace the battery with the proper polarity.
4. Re-install the battery cover and tighten the screw using a screwdriver.
The LED blinks green seven times and then stops blinking.
5. Install the sensor on the base plate by sliding it down.
NOTE: Dispose used batteries, as per statutory regulations.
1 5
2
×7
4
3
DUG_Sensor Climate_ELKO-00 19
LED indications
Pairing
User Action
Press the function key 3 times
LED Indication Status
LED blinks orangeamber, once per second.
Pairing mode is active for 30 seconds.
When pairing is completed, LED glows green for some time before turning Off.
Resetting
User Action
Press the function key 3 times and long press once for > 10 s.
LED Indication
After 10 s, the LED starts blinking red.
Status
The sensor is in reset mode. It is reset to the factory settings after 10 seconds. The sensor then restarts, and the LED starts blinking green before turning Off.
Battery level
LED Indication
LED blinks orangeamber once per minute.
Status
The battery is low (< 10%),
replace the battery, page 19 .
NOTE: A notification pop-up will appear on the app.
Troubleshooting
Symptom
The sensor triggers the automation/ schedule, but does not show the status on the app.
LED blinks orangeamber.
Possible cause
The sensor may be undergoing an over-theair (OTA) firmware update.
The sensor battery is low or drained.
Solution
Wait for the firmware update to complete and then check that the sensor is reporting status.
NOTE: The firmware update runs in the background.
Replace the battery in the device, page 19
NOTE: A notification pop–up will appear on the app.
20 DUG_Sensor Climate_ELKO-00
Technical Data
Battery
Battery life
Nominal power
IP rating
Operating frequency
Max. radio-frequency power transmitted
Operating temperature
Temperature accuracy
Temperature resolution
Relative humidity
Humidity accuracy
Dimensions (H x W x D)
Communication protocol
3 VDC, CR2450
Up to 5 years (may vary based on the usage, frequency of firmware update and environment)
≤90 mW
IP20
2405 – 2480 MHz
≤7 dBm
-10 °C to 50 °C
±1.5 °C
0.1 °C
10 % to 95 %
±5 %
45 x 45 x 17.2 mm
Zigbee 3.0 certified
DUG_Sensor Climate_ELKO-00 21
Trademarks
This guide makes reference to system and brand names that are trademarks of their relevant owners.
• Zigbee ® is a registered trademark of the Connectivity Standards Alliance.
• Apple ® and App Store ® are brand names or registered trademarks of Apple Inc.
• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
• Wi-Fi ® is a registered trademark of Wi-Fi Alliance ® .
Other brands and registered trademarks are the property of their respective owners.
ELKO AS
Sandstuveien 68, 0680 OsloPb 6598 Etterstad, 0607 Oslo
Norway
+47 67 79 39 00 [email protected]
www.elko.no
As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.
© 2023 – 2023 ELKO AS . All rights reserved.
DUG_Sensor Climate_ELKO-00
advertisement