Portech MV-374 User manual

MV-374 / MV-378
VoIP GSM Gateway
User Manual
MV-374
MV-378
PORTech Communications Inc.
VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
【Content】
1.INTRODUCTION .................................................................................................................1
2.FUNCTION DESCRIPTION ...............................................................................................1
3.PARTS LIST ..........................................................................................................................1
4.DIMENSION : 30X28X4 CM...............................................................................................2
5.CHART OF THE DEVICE ..................................................................................................3
6.WEB PAGE SETTING .........................................................................................................4
7.SYSTEM INFORMATION. .................................................................................................5
8. ROUTE ..................................................................................................................................5
9.MOBILE...............................................................................................................................12
10.NETWORK........................................................................................................................20
11.SIP SETTING ....................................................................................................................25
12. NAT TRANS .....................................................................................................................34
13.SYSTEM AUTHORITY ...................................................................................................35
14.UPDATE.............................................................................................................................36
15.SAVE CHANGE ................................................................................................................38
16.REBOOT ............................................................................................................................39
17. IP SETTING .....................................................................................................................40
18.SPECIFICATION .............................................................................................................42
19. APPENDIX: SETUP MV-374/MV-378 WITH ASTERISK.........................................43
20.HOW TO SETUP ASTERISK TO RECEIVE CALLER ID FROM MV-374/MV-378
..................................................................................................................................................50
21. SIMPLE STEPS................................................................................................................59
VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
1.Introduction
MV-374/MV-378 is a 4 / 8 channels VoIP GSM Gateway for call
termination (VoIP to GSM ) and origination (GSM to VoIP). It is SIP
based and compatible with Asterisk. It can enable to make 4 / 8 calls
simultaneously from IP phones to GSM networks and GSM network to IP
phone.
2.Function description
2.1 VoIP(SIP)、GSM conversion.
2.2 50 sets of LAN->MOBILE routes setting，50 sets of MOBILE->LAN
routes setting.
2.3 Voice response for setting and status (dial in from mobile).
2.4 Series connections to save bills.
2.5 Standard SIP(RFC2543,RFC3261) protocol，
Communicates with other gateway or PC.
3.Parts list
Please check the parts for any missing parts. If do, please contact
our agents：
3.1 「MV-374/MV-378」main body
3.2 Power adaptor AC-DC (110V AC – 12V DC) or (220V AC – 12V DC)
3.3 Network cable
3.4 Antenna: MV-374:1 pcs / MV-378: 2 pcs
3.5 Rackmount (compatible with 19“Rack) – option
3.6 User Manual
-1VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
(3.1) MV-378
(3.1) MV-374
(3.2) MV-378
(3.2) MV-374
(3.4)
(3.3)
(3.5)-option
4.Dimension : 30x28x4 cm
-2VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
5.Chart of the device
5.4
5.3
5.8
5.5 5.6 5.7
5.1
5.2
5.1 Antenna：Antenna connector.
5.2 WAN: RJ-45 internet connector，standard RJ-45 socket，connect to
HUB.
5.3 DC 12V：Power input.
5.4 SIM Card
5.5 LINK Indicator：Light up when network is connected.
5.6 CH3：an indicator light of VoIP3
5.7 CH4：an indicator light of VoIP4
5.8 PWR (Power LED)：Light up when power is normal.
-3VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
6.Web Page Setting
When the IP setting is done, the operator may setup all the rest
parameters via web page. Browse the IP address from Internet
Explorer (e.g. http://192.168.0.100)。The following page shows up：
Enter the username and password for authentication. (default
username=voip, password=1234). The page follows when the
username and password are correct.
-4VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
7.System Information.
7.1 When you login the web page, you can see the demo system current
system information like firmware version, company… etc in this
page.
7.2 Also you can see the function lists in the left side. You can use
mouse to click the function you want to set up.
8. Route
Important:
The route table -50 sets can share by two channels(1,2 ch / 3,4 ch /
5,6 ch / 7,8 ch ) . The setting,please refer 9.2 Mobile setting
ex: Mobile 1 use the route table for item 0-24,
Mobile 2 use the route table for item 25-49
-5VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
8.1 Mobile TO LAN Settings
The operator may assign 50 sets of routing rule to transfer the call
incoming from MOBILE to LAN.
The MV-374/MV-378 will transfer to the URL according to the caller ID of
the Mobile.
*CID：
(1) may enter the whole number, e.g. 0911111111
(2) only part of the number (prefix) e.g. 0911* means any number
starting with 0911 will be accepted
(3) * means all numbers can be accepted
-6VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
(4) N means the calls without the CID
Please note the priority of the rules. The item which has more digits will
have higher priority. If the digits are the same, then former one gets the
higher priority.
*URL：The IP address to transfer this call
(1) may enter the whole IP address, e.g. 192.168.0.101 or proxy
extension or phone number.
(2) If this field is blank or simply ‘N’, it means refuse to transfer.
(3) If
an ‘*’ entered, it means
2-stages-dialing. The call will be
answered and prompt dial tone again to receive the IP address/sip
extension or any phone number as the destination. The caller may
enter the IP such as 192*168*0*101#.
*If the device have register proxy server/Asterisk ,you can enter any
destination phone number. Please note the proxy server/Asterisk
need to set the route of destination phone number.
Example:
(1) Mobile to Lan: 0932*,0911123456
MV-374/MV-378 have register proxy server/Asterisk
The proxy server/Asterisk have the route “09”
When the caller’s prefix number is 0932,MV-374/MV-378 will
connect 0911123456 automaticlly
(2) Mobile to Lan: *,*
Any caller call the MV-374/MV-378’s sim,MV-374/MV-378 will
prompt dial tone.Caller can enter IP or sip extension or phone
number.
*sip extension or phone number both need to register SIP Proxy
Server or Asterisk.
*Phone number, SIP Proxy Server or Asterisk need to set the route
of this phone number.
-7VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
8.2 Mobile to LAN Speed Dial Settings
When you set Mobile to LAN Speed Dial Settings and Mobile to
LAN at the same time,MV-374/MV-378 will give priority to Mobile to LAN
Speed Dial Settings.
*The call will be answered and prompt dial tone again. When the caller
may enter the “Num”, system will connect the “URL” as destination.
E.g Num:0 Name:test URL:192.168.0.107
When the caller hear dial tone and enter 0, system will connect
192.168.0.107
-8VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
8.3 LAN to Mobile Settings
The operator may assign 50 sets of routing rule to transfer the call
incoming from LAN to MOBILE.
The MV-374/MV-378 will transfer to the mobile number according to the
incoming URL
*URL：The IP address of the incoming call.
may enter the whole IP address, e.g. 192.168.0.101 or proxy server’s
extension. If a simple ‘*’ is entered, means no restriction for the
incoming IP address.
-9VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
*Call Num：
1.may enter the whole number, e.g. 0911111111
2.a simple *”means 2-stages-dialing. The call will be answered and
prompt dial tone again to receive the called number as the
destination, e.g. 0911111111 or 0911111111#
3.#['d'n]['a'ppp] for one-stage dialing
[...] is option
'd'n means to delete the beginning n codes,
'a'ppp means to add 'ppp' in front.
for example #d2a09 means one-stage dialing,
delete the first 2 codes from your destination number,
then add 09 in front as the new destination number.
Example:
Lan to Mobile: *, #
(1)MV-374/MV-378 and Lan Phone both need to register proxy server or Asterisk.
(2)Proxy server/asterisk set the route that the prefix of destination number
(3)When you dial any destination phone number from lan phone,MV-374/MV-378 will
connect this call auto.
Example of Application:
When you call the ch.1 MV-374/MV-378 gsm number,it will provide dial tone and you
enter a destination number.
Then ch.2 MV-374/MV-378 will dial this number and connect.
ch.1 MV-374/MV-378: mobile to lan set route table *,*
ch.2 MV-374/MV-378:lan to mobile set route table *,#
Additionally, two channels MV-374/MV-378 both need to register proxy server or
Asterisk.
And proxy server/asterisk set the route that the prefix of destination number dial out
from ch.2 MV-374/MV-378.
-10VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
MV-374/MV-378’s IP:
The channel 1:192.168.0.100:5060
The channel 2:192.168.0.100:5062
The channel 3:192.168.0.102:5060
The channel 4:192.168.0.102:5062
The channel 5:192.168.0.104:5060
The channel 6:192.168.0.104:5062
The channel 7:192.168.0.106:5060
The channel 8:192.168.0.106:5062
-11VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
9.Mobile
9.1 Mobile Status
(1)Choose Mobile 1,2,3 or 4 (MV-378: Mobile 1,2,3,4,5,6,7,8)
(2)Network Registration：The telecom carrier which the SIM card been
registered.
(3)SIM Card ID：SIM card ID.
(4)Signal Quality：Signal quality.
(5)GSM S/N : IMEI Number
(6)Incoming IP：The IP address of the last incoming call from LAN.
(7)Incoming IP Name: proxy server name
(8)Outgoing IP：The IP address of the last outgoing call to LAN.
(9)Incoming Mob：The caller ID of the last incoming call from MOBILE.
(10)Outgoing Mob ： The called number of the last outgoing call to
MOBILE.
-12VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
9.2 Mobile Setting
(1)
(3)
(2)
(4)
(5)
(7)
(9)
(10)
(11)
(6)
(8)
(12)
LAN
Mobile 1:
(6)Rx
VoIP
(5) Tx
Codec
GSM
DTMF
(1)VoIP Tx Gain
(2) VoIP Rx Gain
Mobile 2:
Rx
Codec
Tx
GSM
DTMF
-13VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
(1) VoIP Tx Gain: To adjust the volume of LAN side.
(2) VoIP Rx Gain: To adjust the volume of Mobile side.
(3)LAN Dialtone Gain: DTMF Reciver is not good, you can adjust gain
down.
(4)Routing Range:The route table -50 sets can share by two
channels(1,2 ch / 3,4 ch / 5,6 ch / 7,8 ch )
ex: Mobile 1 use the route table for item 0-24,
Mobile 2 use the route table for item 25-49
(5)CODEC Tx Gain: as above
(6)CODEC Rx Gain: as above
(7) SIP From: Caller ID transfer
Tel/User(Standard): If you need to register to Asterisk and proxy
server, please choose this option. And how to transfer the caller ID
to LAN, please refer 21.How to setup Asterisk to receive Caller ID
from MV-374/MV-378 (page 42)
MV-374/MV-378 will send the message as follows in the Packet.
From: " caller number " <sip:[email protected]>;tag=51088abb
User/User(Standard): If you need to register to Asterisk and proxy
server, please choose this option.
MV-374/MV-378 will send the message as follows in the Packet.
From: " 3001" <sip:[email protected]>;tag=51088abb
Tel/Tel :
MV-374/MV-378 will send the message as follows in the Packet.
From: "caller number" <sip: caller number @192.168.0.228>;tag=6ac93f7c
※Please note: If you choose this option, please don’t register to
Asterisk and proxy server. Please only fill proxy server IP and
choose Active: on (else field empty) in sip setting/service demain
-14VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
User/Tel
MV-374/MV-378 will send the message as follows in the Packet.
From: " Username " <sip: caller number @192.168.0.228>;tag=7f130947
※ If you choose this option, please don’t register to Asterisk and
proxy server. Please only fill proxy server ip,Username and
choose Active: on (else field empty) in sip setting/service
demain
(8)Answer Delay: Delay for incoming call when the ring.
(9)Presentation CLIR : If you need to block the Caller Id for call
termination, please choose Suppression
(10)Mobile PIN Code: If you need to unlock pin code via
MV-374/MV-378,you can click “On” and enter pin code.
(11)LAN Answer Mode:
Answered : when mobile answer,then connect the call
Alerted : when the mobile is ringing back tone,then connect the call
Income : when lan dial out,then connect soon
(12) ON/Off: If you use this channel, please click on. Otherwise, please
click off.
9.3 Mobile / Forward Setting :
When the first route are busying, SIP can transfer phone call to
another free route. When the device are busying, the phone call
can be transfer to another device (external equipments).
-15VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
* "Forward Enable" is not motivate on Defualt value.
So please, mark "Forward Enable" this blank to motivate this function.
Take SJ Phone for example: Profiles -> Edit -> Advanced -> Accept
redirection replies (Turn on the "Forward Enable", therefore the SJ
Phone can designate a port which are free to use.)
-16VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
URL:Port
Name
192.168.0.100:5060
Fwd to Mobile1:
192.168.0.100:5062
Fwd to Mobile2:
Fwd to External:
The Explanation of Picture:
Fwd to Mobile1:192.168.0.100 : 5060, it means when 5062 Port are
busying, SJ Phone can transfer the call to 5060 Port (192.168.0.100).
Fwd to Mobile2:192.168.0.100 : 5062, it means when 5060 Port are
busying, SJ Phone can transfer the call to 5062 Port (192.168.0.100).
If both 5060 port and 5062 port are busying at same time, you can set
up "Fwd to External", then you can transfer the phone call to another
designate device.
-17VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
9.4 Mobile / SMS Agent :
Read received SMS
(1) Rx List: Read received SMS
(2) Dest Num: the Receiver’s phone number
(3) Message: Please fill the message that want to send to receiver.
When you click Rx List, you can view all received SMS as follows.
-18VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Click the serial no,you can view message as follows.
-19VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
10.Network
In Network you can check the Network status, configure the WLAN
Settings , LAN Setting and SNTP settings.
10.1 Network Status: You can check the current Network setting in this
page.
-20VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
10.2 WAN Settings: You can check the current Network setting in this
page.
(1) The TCP/IP Configuration item is to setup the WAN port’s network
environment. You may refer to your current network environment to
configure the system properly.
(2) The PPPoE Configuration item is to setup the PPPoE Username and
Password. If you have the PPPoE account from your Service
Provider, please input the Username and the Password correctly.
(3) The Bridge Item is to setup the system Bridge mode Enable/Disable.
If you set the Bridge On, then the two Fast Ethernet ports will be
transparent.
(4) When you finished the setting, please click the Submit button.
-21VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
10.3 LAN Settings: You can check the current Network setting in this
page.
(1) The TCP/IP Configuration item is to setup the WAN port’s network
environment. You may refer to your current network environment to
configure the system properly.
(2)DHCP Server: You may refer to your current network environment to
configure the system properly
-22VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
10.4 SNTP Settings:
SNTP Setting function: you can setup the primary and second SNTP
Server IP Address, to get the date/time information. Also you can base
on your location to set the Time Zone, and how long need to synchronize
again. When you finished the setting, please click the Submit button.
-23VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
10.5 Slave Settings: Record Slave IP for Master
-24VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.SIP Setting
In SIP Setting you can setup the Service Domain,Port Settings,Codec
Settings,RTP setting,RPort Setting and Other SettingS. If the VoIP
service is provided by ISP,you need to setup the related informations
correctly then you can register to SIP Proxy Server correctly.
11.1 In Servcie Domain Function you need to input the account and the
related informations in this page, please refer to your ISP Provider.
You can register three SIP accounts . You can dial the VoIP phone
to your friends via first enable SIP account and receive the phone
from the tree SIP account.
First you need to click Active to enable the Service Domain, then you can
input the following items.
(1) Choose Mobile 1 , 2, 3 or 4
-25VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
(2) Display name: you can input the name you want to display.
(3) User name: you need to input the User Name get from your ISP.
(4) Register Name: you need to input the Register Name get from your
ISP.
(5) Register Password: you need to input the Register Password get
from ISP.
(6) Domain Server: you need to input the Domain Server get from your
ISP.
(7) Proxy Server: you need to input the Proxy Server get from your ISP.
(8) Outbound Proxy: you need to input the Outbound Proxy get from your
ISP. If your ISP does not provide the information, then you can skip
this item.
(9) You can see the Register Status in the Status item.
(10) When you finished the setting, please click the Submit button.
Remember to click “Save Charge”
Example:
Register VoipBuster
Your Voipbuster username
Your Voipbuster password
Proxy Server’s IP
-26VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.2 Port Setting
You can setup the SIP and RTP port number in this page. Each ISP
provider will have different SIP/RTPport setting, please refer to the ISP
to setup the port number correctly. When you finished the setting, please
click the Submit button.
-27VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.3 Codec Settings:
You can setup the Codec priority, RTP packet length in this page. You
need to follow the ISP suggestion to setup these items. When you
finished the setting, please click the Submit button.
-28VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.4 Codec ID Setting
You can setup the Codec ID in this page.
-29VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.5 DTMF Setting
You can setup the DTMF Setting in this page.
-30VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.6 RPort Function:
You can setup the RPort Enable/Disable in this page. To change this
setting, please following your ISP information. When you finished the
setting, please click the Submit button.
-31VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.7 SIP Responses
11.7.1 486(busy here), 503(Service unavailable): When Device are
busying, you can select 486 or 505 to response to SIP.
11.7.2 180 Ring on/off: LAN TO MOBILE two stage dialing can be turn
off, therefore there will be no the Ring Back Tone, all the phone call will
be transferred to Voice-Mail directly. (For this function, 183 must be turn
on)
-32VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
11.7.3 183(Session Progress)-->[It means "on progressing"]: When you
turn 183 on, it means you can hear voicemail while GMS side are
busying. We recommend you to turn this on if you use SIP Proxy.
11.8 Other Settings
Other Settings: you can setup the Hold by RFC and QoS in this page. To
change these settings. please following your ISP information. When you
finished the setting, please click the Submit button. The QoS setting is to
set the voice packets’ priority. If you set the value higher than 0, then the
voice packets will get the higher priority to the Internet. But the QoS
function still need to cooperate with the others Internet devices.
-33VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
12. NAT Transform
In NAT Trans. you can setup STUN and uPnP function. These functions
can help your VoIP device working properly behind NAT.
12.1 STUN Setting: you can setup the STUN Enable/Disable and STUN
Server IP address in this page. This function can help your VoIP
device working properly behind NAT. To change these settings
please following your ISP information. When you finished the
setting, please click the Submit button.
-34VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
13.System Authority
In System Authority you can change your login name and password.
-35VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
14.Update
In Update you can update the system’s firmware to the new one or do the
factory reset to let the system back to default setting.
14.1 Update firmware
(1) In New Firmware function you can update new firmware via HTTP in
this page. You can upgrade the firmware by the following steps:
(2)Select the firmware code type, Risc code.
(3)Click the “Browse” button in the right side of the File Location or you
can type the correct path and the filename in File Location blank.
(4)Select the correct file you want to download to the system then click
the Update button.
(5) Please click update/default setting after update firmware
-36VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
14.2 Restore Default Settings
In this page: Update/ Default Settings, you could restore the factory
default settings to the system. All setting will restore default setting.
IP will retain original IP as usual not default IP.
-37VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
15.Save Change
In Save Change you can save the changes you have done. If you want to
use new setting in the VoIP system, You have to click the Save button.
After you click the Save button, the system will automatically restart and
the new setting will effect.
-38VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
16.Reboot
Reboot function you can restart the system. If you want to restart the
system, you can just click the Reboor button, then the system will
automatically.
-39VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
17. IP Setting
The operator can setup or query the network parameters by dialing in the
mobile number which it SIM card has been put in the main body. The
status or result is response by voice. In the first 20 seconds after
power-on, the VoIP GSM Gateway enters the IP setting mode. The
operator may dial in the mobile number during this period to set or query
the network parameters.
Item
IVR Action
IVR Menu Choice
1
Reboot
#195#
2
Factory Reset
#198#
3
Check IP Address #120#
4
Check IP Type
#121#
5
Check Network
Mask
#123#
6
Check Gateway #124#
IP
Address
Check Primary
#125#
7
Notes
After you hear “Option
Successful,” hang-up. Unit will
reboot automatically.
System will automatically
Reboot.WARNING: ALL
User-Changeable”
NONDEFAULT SETTINGS
WILL BE LOST! This will
include network and service
provider data.
IVR will announce the current
IP
address
,
Default
:
192.168.0.100
IVR will announce if DHCP in
enabled or disabled.
default : OFF
IVR will announce the current
network mask.Default :
255.255.255.0
IVR will announce the current
gateway IP address,
Default : 192.168.0.254
IVR will announce the current
-40VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
DNS Server
8
9
Check Firmware #128#
Version
Set as DHCP #111#
client
10
Set Static IP
Address
#112xxx*xxx*xxx
*xxx#
11
Set Network Mask #113xxx*xxx*xxx
*xxx#
12
Set Gateway IP
Address
13
Set Primary DNS #115xxx*xxx*xxx
Server
*xxx#
#114xxx*xxx*xxx
*xxx#
setting in the Primary DNS
field.
Default : 192.168.0.1
IVR will announce the version
of the firmware running
The system will change to
DHCP
Client type
DHCP will be disabled and
system will change to the
Static IP type.
Enter IP address using
numbers on the telephone key
pad. Use the * (star) key when
entering a decimal point.
Must set Static IP first.
Enter value using numbers on
the telephone key pad. Use
the * (star) key when entering
a decimal point.
Must set Static IP first.
Enter IP address using
numbers on the telephone key
pad. Use the * (star) key
when entering a decimal
point.
Must set Static IP first.
Enter IP address using
numbers on the telephone key
pad. Use the * (star) key
when entering a decimal
point.
-41VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
18.Specification
18.1 Protocols
SIP (RFC2543,RFC3261)
18.2 TCP/IP
IP/TCP/UDP/RTP/RTCP/
CMP/ARP/RARP/SNTP
DHCP/DNS Client
IEEE802.1P/Q
ToS/DiffServ
NAT Traversal
STUN
uPnP
IP Assignment
Static IP
DHCP
PPPoE
18.3 Codec
G.711 u-Law
G.711 a-Law
G.723.1 (5.3k)
G.723.1 (6.3k)
G.729A
G.729A/B
18.4 Voice Quality
VAD
-42VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
CNG
AEC, LEC
Packet loss
18.5 GSM (MV-374/MV-378)
Dual BAND: 900/1800 MHZ
Tri BAND(BenQ M23): 900/1800/1900 MHZ
Tri BAND(Siemens MC56): 850/1800/1900 MHZ
Quad BAND: 900/1800/1900/850 MHZ
19. Appendix: Setup MV-374/MV-378 with Asterisk
19.1 Usage
A typical usage of such a gateway is to be able to give a call with your
normal mobile to any destination at voip cost :
Your mobile <----gsm network----> MV-374/MV-378 <--lan--> Asterisk
<--internet--> VOIP provider <--whatever--> landline
To do such a call, you just call your MV-374/MV-378 number (it has its
own simcard), then you get an invitation tone, then you dial the number
which is handled by Asterisk.
If you have some special deals with your mobile operator, like free
special number, you can call your MV-374/MV-378 for free.
You can then call all around the world from your mobile at voip cost :-)
19.2 MV-374/MV-378 Configuration
Once you've configured everything in the box, one good advice is to
unplug the power and to restart it. By this way you should have all the
parameters taken into account.
To have the MV-374/MV-378 to work with Asterisk, you need first to
-43VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
configure the box.
Here are some screen shots showing all the important parameters.
You have to note that in all the configuration process, the
MV-374/MV-378 is considered as extension '103' of the IPBX.
In Bold are the parameters depending on your installation
-44VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Here the '#' is important to avoid the two stage dialing when you give a
call from Asterisk to GSM.
The mobile number you give in that page are the authorised mobile
which can call GSM to Asterisk.
-45VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
These mobile number must be defined as your GSM provider displays
the number.
If you don't know how it is displayed, just give a call to the box and check
the number given in the 'Incoming Mob' field of the 'Mobile Status' page.
Any number which is not in that list won't have acces to the LAN side, so
to Asterisk.
If you want to allow any number, just set '*' in that field ... but beware of
the bill ;-)
Once Asterisk configuration is made, you should get 'Registered' on the
Realm1.
-46VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
It is very important to use only u-law or a-law as all DTMF is inband.
So if you want to be able to do some DISA when you call from GSM to
Asterisk, it has to be one of these 2 codecs.
These settings seem to be ok, just adjust ...
-47VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
19.3 Antenna position
Another important thing is to properly place the provided antenna.
If your gsm reception is good, you should get around 18 or 19 as Signal
Quality in the "Mobile Status" page.
With that level of signal quality, your audio quality will be very good.
On the other end,the signal quality down to 11, audio becomes very jerky.
So, maximum signal quality = maximum audio quality.
19.4 Asterisk configuration
Once the MV-374/MV-378 is set, you have to configure Asterisk.
On that side, you have to setup files as follow :
19.5 sip.conf
; GSM VOIP Gateway MV-374/MV-378
[103]
type=friend
username=103
fromuser=103
regexten=103 ; When they register, create extension 401
secret=xxxxxxx ; Asterisk extension password
context=gateway ; Incoming calls context
dtmfmode=inband ; Very important for DISA to work
call-limit=1 ; Limit to 1 call max
callerid=GSM Gateway <103>
host=dynamic
nat=no ; Gateway is not behind a NAT router
canreinvite=no ; Typically set to NO if behind NAT
insecure=very
qualify=yes
disallow=all
allow=ulaw ; prefered codec for DTMF detection
allow=alaw
19.6 extensions.conf
-48VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
; ******* GSM Gateway incoming calls **********
[gateway]
exten => _103,1,Answer()
exten => _103,2,DigitTimeout(3) ; give enough time to do second stage
dialing
exten => _103,3,ResponseTimeout(5)
exten => _103,4,DISA(no-password|outgoing) ; here 'outgoing' is the
normal context to deal with the dial plan
[outgoing]
...
; example of LAN to GSM call
; call the MV-374/MV-378 sim card mail box thru GSM
exten => _888,1,SetCallerID("xxxxxxxxxx")
exten => _888,2,Dial(SIP/${EXTEN}@103,60,r)
exten => _888,3,Hangup()
-49VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
20.How to setup Asterisk to receive Caller ID from
MV-374/MV-378
Test version
trixbox-2.2
SIP Softphone
SJPhone 1.60.289a
X-Lite 1105x
Modify file
Add the following setting to/etc/asterisk/sip.conf
[1000]
type=friend
secret=1000
qualify=yes
nat=yes
host=dynamic
canreinvite=no
context=internal
[1001]
type=friend
secret=1001
qualify=yes
nat=yes
host=dynamic
canreinvite=no
context=internal
[1002]
type=friend
-50VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
secret=1002
qualify=yes
nat=yes
host=dynamic
canreinvite=no
context=internal
Add the following setting to /etc/asterisk/extensions.conf
[internal]
exten => 1000,1,Dial(SIP/1000)
exten => 1001,1,Dial(SIP/1001)
exten => 1002,1,Dial(SIP/1002)
configure:
trixbox-2.2: address=192.168.66.202:5060
SJPhone: address=192.168.66.145:5060; username=1000,
displayname=user_1000
X-Lite: address=192.168.66.145:7331; username=1001, displayname=user_1001
MV-374/MV-378: address=192.168.66.203:5060; username=1002,
displayname=user_1002
test1
pstn call 0928492911(mobile number) MV-374/MV-378 hear the second dial
tone,call SoftPhone’s number SoftPhone show pstn caller id
This Is X-Lite receiving packet, red word is pstn number. Test ok.
INVITE sip:[email protected]:7331 SIP/2.0
Via: SIP/2.0/UDP 192.168.66.202:5060;branch=z9hG4bK3d0bbaf7;rport
-51VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
From: "035678238" <sip:[email protected]>;tag=as580472a7
To: <sip:[email protected]:7331>
Contact: <sip:[email protected]>
Call-ID: [email protected]
CSeq: 102 INVITE
User-Agent: Asterisk PBX
Max-Forwards: 70
Date: Tue, 22 May 2007 02:50:37 GMT
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Content-Type: application/sdp
Content-Length: 242
v=0
o=root 2737 2737 IN IP4 192.168.66.202
s=session
c=IN IP4 192.168.66.202
t=0 0
m=audio 15852 RTP/AVP 0 8 101
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
a=silenceSupp:off - - - SIP/2.0 200 Ok
Via: SIP/2.0/UDP 192.168.66.202:5060;branch=z9hG4bK3d0bbaf7;rport
From: "035678238" <sip:[email protected]>;tag=as580472a7
To: <sip:[email protected]:7331>;tag=677373503
Contact: <sip:[email protected]:7331>
Call-ID: [email protected]
CSeq: 102 INVITE
Content-Type: application/sdp
Server: X-Lite release 1105x
-52VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
Content-Length: 254
v=0
o=1001 4804366 4807851 IN IP4 192.168.66.145
s=X-Lite
c=IN IP4 192.168.66.145
t=0 0
m=audio 8000 RTP/AVP 0 8 3 101
a=rtpmap:0 pcmu/8000
a=rtpmap:8 pcma/8000
a=rtpmap:3 gsm/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
test 2
SoftPhone call 1002 MV-374/MV-378 hear second dial tone and call pstn pstn answer show caller id-mobile number 0928492911
This Is X-Lite receiving packet. Test ok.
INVITE sip:[email protected] SIP/2.0
Via: SIP/2.0/UDP
192.168.66.145:7331;rport;branch=z9hG4bK4C4315351FC84CA582D14FB8C25F
C3BF
From: user_1001 <sip:[email protected]:7331>;tag=1121869743
To: <sip:[email protected]>
Contact: <sip:[email protected]:7331>
Call-ID: [email protected]
CSeq: 63148 INVITE
Proxy-Authorization: Digest
username="1001",realm="asterisk",nonce="0d3b2879",response="8aaaaa5b5ad53
-53VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
654bf0a2ab0fa9bb118",uri="sip:[email protected]",algorithm=MD5
Max-Forwards: 70
Content-Type: application/sdp
User-Agent: X-Lite release 1105x
Content-Length: 254
v=0
o=1001 5111461 5111501 IN IP4 192.168.66.145
s=X-Lite
c=IN IP4 192.168.66.145
t=0 0
m=audio 8000 RTP/AVP 0 8 3 101
a=rtpmap:0 pcmu/8000
a=rtpmap:8 pcma/8000
a=rtpmap:3 gsm/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
SIP/2.0 200 OK
Via: SIP/2.0/UDP
192.168.66.145:7331;branch=z9hG4bK4C4315351FC84CA582D14FB8C25FC3BF
;received=192.168.66.145;rport=7331
From: user_1001 <sip:[email protected]:7331>;tag=1121869743
To: <sip:[email protected]>;tag=as2a2fbf98
Call-ID: [email protected]
CSeq: 63148 INVITE
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Contact: <sip:[email protected]>
Content-Type: application/sdp
Content-Length: 242
-54VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
v=0
o=root 2737 2737 IN IP4 192.168.66.202
s=session
c=IN IP4 192.168.66.202
t=0 0
m=audio 13798 RTP/AVP 0 8 101
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
a=silenceSupp:off - - - register issue
The packet date from Asterisk as follows.
Please note, user_1002’s display name don’t appear
So the website’s Display Name is not available
<-- SIP read from 192.168.66.203:5060:
REGISTER sip:192.168.66.202 SIP/2.0
Via: SIP/2.0/UDP
192.168.66.203:5060;rport;branch=z9hG4bK590e92b551233a10a0ae71944c19b5
aa
From: <sip:[email protected]>;tag=4e36d8f1
To: <sip:[email protected]>
Call-ID: [email protected]
Contact: <sip:[email protected]:5060>
CSeq: 10 REGISTER
Expires: 300
Authorization: Digest
username="1002",realm="asterisk",nonce="3ca93a1e",response="4d39ccb0dae64
bb2f1341e9896ac1ea7",uri="sip:192.168.66.202",algorithm=MD5
User-Agent: CMI CM5K
Content-Length: 0
-55VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
--- (11 headers 0 lines) --Using latest REGISTER request as basis request
Sending to 192.168.66.203 : 5060 (NAT)
Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP
192.168.66.203:5060;branch=z9hG4bK590e92b551233a10a0ae71944c19b5aa;rec
eived=192.168.66.203;rport=5060
From: <sip:[email protected]>;tag=4e36d8f1
To: <sip:[email protected]>
Call-ID: [email protected]
CSeq: 10 REGISTER
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Contact: <sip:[email protected]>
Content-Length: 0
--Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 401 Unauthorized
Via: SIP/2.0/UDP
192.168.66.203:5060;branch=z9hG4bK590e92b551233a10a0ae71944c19b5aa;rec
eived=192.168.66.203;rport=5060
From: <sip:[email protected]>;tag=4e36d8f1
To: <sip:[email protected]>;tag=as13a32ae8
Call-ID: [email protected]
CSeq: 10 REGISTER
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
WWW-Authenticate: Digest algorithm=MD5, realm="asterisk", nonce="5def9231"
Content-Length: 0
-56VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
--Scheduling destruction of call
'[email protected]' in 15000 ms
asterisk1*CLI>
<-- SIP read from 192.168.66.203:5060:
REGISTER sip:192.168.66.202 SIP/2.0
Via: SIP/2.0/UDP
192.168.66.203:5060;rport;branch=z9hG4bK672fa67f59c2223275f5ee286d27597a
From: <sip:[email protected]>;tag=4e36d8f1
To: <sip:[email protected]>
Call-ID: [email protected]
Contact: <sip:[email protected]:5060>
CSeq: 11 REGISTER
Expires: 300
Authorization: Digest
username="1002",realm="asterisk",nonce="5def9231",response="046a412f4e7ed4
e98fd507416994a80a",uri="sip:192.168.66.202",algorithm=MD5
User-Agent: CMI CM5K
Content-Length: 0
--- (11 headers 0 lines) --Using latest REGISTER request as basis request
Sending to 192.168.66.203 : 5060 (NAT)
Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP
192.168.66.203:5060;branch=z9hG4bK672fa67f59c2223275f5ee286d27597a;recei
ved=192.168.66.203;rport=5060
From: <sip:[email protected]>;tag=4e36d8f1
To: <sip:[email protected]>
Call-ID: [email protected]
CSeq: 11 REGISTER
-57VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Contact: <sip:[email protected]>
Content-Length: 0
12 headers, 0 lines
Reliably Transmitting (NAT) to 192.168.66.203:5060:
OPTIONS sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.66.202:5060;branch=z9hG4bK7b92dd8a;rport
From: "Unknown" <sip:[email protected]>;tag=as5dee3942
To: <sip:[email protected]:5060>
Contact: <sip:[email protected]>
Call-ID: [email protected]
CSeq: 102 OPTIONS
User-Agent: Asterisk PBX
Max-Forwards: 70
Date: Tue, 22 May 2007 03:11:54 GMT
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Content-Length: 0
Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 200 OK
Via: SIP/2.0/UDP
192.168.66.203:5060;branch=z9hG4bK672fa67f59c2223275f5ee286d27597a;recei
ved=192.168.66.203;rport=5060
From: <sip:[email protected]>;tag=4e36d8f1
To: <sip:[email protected]>;tag=as13a32ae8
Call-ID: [email protected]
CSeq: 11 REGISTER
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Expires: 300
Contact: <sip:[email protected]:5060>;expires=300
Date: Tue, 22 May 2007 03:11:54 GMT
Content-Length: 0
-58VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
21. Simple Steps
Step 1. Change the Network setting if you need (Network/network setting)
Step 2. Register SIP proxy Server or Asterisk or VoipBuster if you need
(sip setting/service domain)
Step 3. Set Route ( request )
mobile to lan:
(1) *,* --->it is two stage dialing.
when mobile call in,MV-374/MV-378 will provide dial tone and you
can enter ip or asterisk extension or phone number.
* If you want to enter phone number,please note your asterisk need
to have route of destination number.
(2) *, specific extension or IP or phone number
when mobile call in,MV-374/MV-378 will connect with this specific
extension or IP or phone number auto
* If you want to set specific phone number,please note your asterisk
need to have route of destination number.
Lan to Mobile:
(1) *,* --->it is two stage dialing.
when lan phone call in,MV-374/MV-378 will provide dial tone and
you can enter mobile number.
(2) *, specific mobile number
when lan phone call in,MV-374/MV-378 will connect with the specific
mobile number auto.
(3) *,#--->It is 1 stage dialing
When lan phone and MV-374/MV-378 both register Asterisk,
you can dial any destination number from lan phone directly.
* Please note:Asterisk need to set route of destination number that
dial out from MV-374/MV-378
* All changes both need to click "save and change"
-59VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
-60VoIPon
www.voipon.co.uk
[email protected]
Tel: +44 (0)1245 808195
Fax: +44 (0)1245 808299
">