4.3 inches Facial & Fingerprint Recognition Series - Larcon-Sia

4.3 inches Facial & Fingerprint Recognition Series - Larcon-Sia
4.3
inches
Facial
&
Fingerprint
Recognition Series Product User Manual
Version: 3.0
Date: November 2011
About This Manual
This document introduces the user interface and menu operations of
the 4.3 inches Facial & Fingerprint Recognition series products. For
the installation of the FFR terminal, see Facial & Fingerprint
Recognition Series Product Installation Manual
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Content
1 Instruction for Use ...................................................................................... 1
1.1 The Distance,Facial Expression and Stand Pose......................... 1
1.2 Enrollment Pose.............................................................................. 2
1.3 Finger Placement............................................................................ 3
1.4 Use of Touch Screen ...................................................................... 4
1.5 Touch Operations ........................................................................... 5
1.6 Appearance of the FFR Terminal.................................................... 6
1.7 Main Interface ................................................................................. 7
1.8 Verification Modes .......................................................................... 9
1.8.1 Fingerprint Verification ......................................................... 9
1.8.2 Facial Verification ...............................................................11
1.8.3 Password Verification ........................................................ 14
1.8.4 ID Card Verification
........................................................ 15
2. Main Menu .............................................................................................. 17
3. User Management................................................................................... 20
3.1. Adding a User .............................................................................. 21
3.1.1 Entering a User ID ............................................................. 22
3.1.2 Entering a Name................................................................ 23
3.1.3 Enrolling a Fingerprint ....................................................... 24
3.1.4 Enrolling a Password ......................................................... 25
3.1.5 Enrolling a Face................................................................. 26
3.1.6 Entering a Group No.......................................................... 27
3.1.7 Enrolling an ID Card
...................................................... 28
3.1.8 Enrolling an Mifare Card ................................................. 29
3.1.9 Modify User Rights ............................................................ 29
3.1.10 Enroll Photo ..................................................................... 30
3.2 Edit a User .................................................................................... 31
3.3 Delete a User ................................................................................ 32
I
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.4 Query a User ................................................................................ 33
3.4.1 Query by User ID............................................................... 33
3.4.2 Query by Name ................................................................. 34
4. Communication-related Settings ............................................................. 35
4.1 Network Settings........................................................................... 35
4.2 Serial Port Settings ....................................................................... 37
4.3 WIFI Option
............................................................................... 38
4.4 Wiegand Output ............................................................................ 40
4.4.1 Wiegand 26-bits Output Description .................................. 40
4.4.2 Wiegand 34-bits Output Description .................................. 42
4.4.3 Customized Format ........................................................... 44
5. System Configuration .............................................................................. 48
5.1 General ......................................................................................... 48
5.2 Display .......................................................................................... 49
5.3 Fingerprint..................................................................................... 50
5.4 Face.............................................................................................. 51
5.5 Log Settings .................................................................................. 52
5.6 Update .......................................................................................... 54
6. Data Management................................................................................... 55
6.1 Query a Record............................................................................. 56
6.2 Work Code .................................................................................... 57
7. USB Disk Management ........................................................................... 59
8. Keyboard Definitions ............................................................................... 60
9 Auto Test .................................................................................................. 62
10 Screen Calibration.................................................................................. 64
11 Bell Setting ............................................................................................. 65
12 Access Control Setting ........................................................................... 67
13 Date/Time Setting................................................................................... 68
II
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
13.1 Set Date/Time ............................................................................. 68
13.2 Set Daylight Saving Time (DLST) ............................................... 69
14 System Information ................................................................................ 71
14.1 Records ...................................................................................... 71
14.2 Device......................................................................................... 72
14.3 Power Info
............................................................................... 72
Appendix ..................................................................................................... 73
Appendix 1 Text Input Instructions...................................................... 73
Appendix 2 Rules for Uploading Promotional Pictures........................ 75
Appendix 3 Introduction to Wiegand ................................................... 76
Appendix 4 USB Host ......................................................................... 78
Appendix 5 State Auto Switch............................................................. 78
Appendix 6 Photo ID Function ............................................................ 79
Appendix 7 Statement on Human Rights and Privacy ........................ 81
Appendix 8 Environment-Friendly Use Description............................. 83
III
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1 Instruction for Use
1.1 The Distance,Facial Expression and Stand Pose
1) The recommended distance:
The recommended distance between person and
device is 0.5m (applied to height range
1.5~1.85m). According to the obtained face image
from device to adjust, when the face image is
comparatively bright, please move backwards
appropriately; when the face image is
comparatively dark, please move forwards
appropriately.
2) The recommended facial expression and several poor-effect facial
expressions:
3 ) The recommded stand pose and several poor-effect stand poses:
Note: During the enrollment and verification, please remain the normal
facial expression and stand pose.
1
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.2 Enrollment Pose
During the enrollment, display the face in the centre of screen as possible. According
to the prompt appears on the device’s screen, put the eyes in the green box. The
user needs to move forward and backward to adjust the eyes positiont during the
face registration. The enrollment poses are as follows:
2
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.3 Finger Placement
Recommended fingers: The index finger, middle finger or the ring finger; the thumb
and little finger are not recommended (because they are usually clumsy on the
fingerprint collection screen).
1)
Proper finger placement:
The finger is flat to the surface
and centered in fingered guide.
2)
Improper finger placement:
Not flat to the surface
Off-center
Off-center
Slanting
Please enroll and verify your fingerprint by using the proper finger
placement mode. We shall not be held accountable for any
consequences arising out of the degradation in verification
performance due to improper user operations. We shall reserve
the right of final interpretation and revision of this document.
3
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.4 Use of Touch Screen
Touch the screen with one of your fingertips or the top of the forward edge of a
fingernail, as shown in the following figure. A broad point of contact may lead to
inaccurate pointing.
When the touch screen is less sensitive to the touch, you can perform screen
calibration through menu operations. Press [Menu] → [Calibration] on the screen
and a cross icon will be displayed. After you touch the center of the cross at five
locations on the screen correctly, the system automatically returns to the main menu.
Press [Return] to return to the initial interface. For details, see “10 Screen
Calibration” in this manual.
Smear or dust on the touch screen may affect the performance of the touch screen.
Therefore, try to keep the screen clean and dust-free.
4
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.5 Touch Operations
(1) Enter numbers. Press the [User ID] key. The system automatically displays the
number input interface. After entering the user ID, press [OK] to save and return to
the previous interface.
(2) Enter Text. Press the [Name] key. The system automatically displays the text
input interface. After entering the user name, press [X] to save and return to the
previous interface.
(3) Modify parameters. Press the default value of a parameter and the system
automatically switches to another value of this parameter.
5
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.6 Appearance of the FFR Terminal
Indicator
Touch screen
Push buttons
Finger Sensor
ID card
area
Camera
6
swipe
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.7 Main Interface
① Menu
② Time
③ Date
④ 1:1/1: G Function Key
⑤Facial Image
⑥ Group No.
⑦Attendance Status
⑧Screen Shortcut Keys
F1
F2
F3
F4
F5
F6
⑨Keyboard Shortcut Keys
①Menu: You can enter the main menu by touching this key.
②Time: Current time is displayed. Both the 12-hour and 24-hour time systems are
supported.
③Date: Current date is displayed.
④1:1/1: G Function Key: You can enter the digital input interface of 1:1/1: G
verification mode by pressing this key.
⑤Facial Image: Default displays the facial image.
⑥Group No.: Display the current face group number.
⑦Attendance Status: Current attendance status is displayed. This key is hidden
when ⑧ Screen Shortcut Keys are displayed.
⑧Screen Shortcut Keys: Press related shortcut keys to display the attendance
status or enter the functional interface quickly. Users can customize the function of
each shortcut key. For details, see 8 Keyboard Definitions.
7
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
⑨Keyboard Shortcut Keys: The Keyboard Shortcut Keys have a one-to-one
relationship with ⑧Screen Shortcut Keys. Press related shortcut keys to display the
attendance status or enter the functional interface quickly.
8
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.8 Verification Modes
1.8.1 Fingerprint Verification
1.
1: N fingerprint verification
The terminal compares current fingerprint collected by the fingerprint collector with
all fingerprint data on the terminal.
(1) To enter the fingerprint verification mode.
The device automatically distinguishes face
and fingerprint verification, just pressing
finger on the collector. Shall be fingerprint
authentication mode.
(2) Press your finger on the fingerprint
collector by adopting the proper finger
placement. For details, see 1.3 Finger
Placement.
(3) If the verification is successful, an
interface as shown in Figure 1 on the right
will be displayed.
(4) If the verification is not successful, an interface as shown in Figure 2 on the right
will be displayed.
9
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
2.
1:1 fingerprint verification
In the 1:1 fingerprint verification mode, the terminal compares current fingerprint
collected through the fingerprint collector with that in relation to the user ID entered
through keyboard. Adopt this mode only when it is difficult to recognize the
fingerprint.
(1) To enter the 1:1 recognition mode, you
can:
A) Press [1:1] on the screen, as shown in
Figure 1 on the right;
B) Press related shortcut key on the
keyboard.
Note: You can enter the 1:1 recognition
mode through B) only after setting a
shortcut key for “1:1”. For details, see 8
Keyboard Definitions.
(2) Enter user ID and then press the
"Fingerprint” icon (Figure 2 on the right) to
enter 1:1 fingerprint recognition mode. If the
prompt “Unregistered user!” is displayed,
the user ID is nonexistent or the user ID
bearer has not enrolled his/her fingerprint.
(3) Press your finger on the fingerprint
collector by adopting the proper finger
placement. For details, see “1.3 Finger
Placement“.
(4) If the verification is successful, an
interface as shown in Figure 3 on the right
will be displayed. If the verification is not
successful, show as Figure 4.
10
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.8.2 Facial Verification
1.
1: N facial verification
The terminal compares current face image collected by the camera with all face data
on the terminal.
(1) To enter the 1: N recognition mode, the
device automatically distinguishes face and
fingerprint verification.
(2) Compare the facial in a proper way. For
details, see 1.1 The Distance, Facial
Expression and Stand Pose. Comparison
of interface display the current image
collected by the camera, an interface as
shown in Figure 1 on the right will be
displayed.
(3) If the verification is successful, an
interface as shown in Figure 2 on the right
will be displayed.
11
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
2.
1:1 facial verification
The terminal compares current facial collected through the facial collector with that in
relation to the user ID entered through keyboard. Adopt this mode only when it is
difficult to recognize the facial.
(1) To enter the 1:1 recognition mode, you
can:
A) Press [1:1] on the screen, as shown in
Figure 1 on the right;
B)
Press
related
shortcut
key
on
the
keyboard.
Note: You can enter the 1:1 recognition
mode through B) only after setting a
shortcut key for “1:1”. For details, see 8
Keyboard Definitions.
(2) Enter user ID and then press the "1:1
Facial” icon (Figure 2 on the right) to enter 1:1
facial
recognition
mode.
If
the
prompt
“Unregistered user!” is displayed, the user ID
is nonexistent or the user ID bearer has not
enrolled his/her face in the system.
(3) Compare the facial in a proper way. For
details,
see
1.1
The
Distance,
Facial
Expression and Stand Pose. Current facial
collected through the facial collector is
displayed on the comparison interface, as
shown in Figure 3 on the right.
(4) If the verification is successful, an interface as shown in Figure 4 on the right will
be displayed. The system will return to the main interface if the verification is not
passed within 20 seconds.
12
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3. 1: G facial verification
Note: When you open the 1: G Verify function, then you can make 1:G facial
verification. For detail please see 5.5 Log Settings.
Current group No. is displayed on the facial
recognition interface. Users in current group
can perform facial comparison directly. Users of
another group can perform facial comparison
only after entering the group No. or selecting it
using the shortcut key. And the system will set
the group entered or selected by users to be
the current group instantly.
(1) Press [1:1/1: G] on the screen to enter the 1:
G recognition mode, as shown in Figure 1 on
the right.
(2) Enter user Group No. and then press the "1:
G” icon (Figure 2 on the right) to enter 1: G
fingerprint recognition mode.
(3) Compare the facial in a proper way. For
details, see 1.1 Standing Position and Posture,
and Facial Expression. Current Group No. is
displayed on the comparison interface, as
shown in Figure 3 on the right.
Note: Check whether you are in current
group; if not, return to Step 1.
(4) If the verification is successful, an interface
as shown in Figure 4 on the right will be displayed.
13
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.8.3 Password Verification
In the password verification mode, the terminal compares the password entered with
that in relation to the user ID.
(1) To enter the password verification mode,
you can:
A) Press [1:1] on the screen, as shown in
Figure 1 on the right;
B) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition
mode through B) only after setting a
shortcut key for “1:1”. For details, see 8
Keyboard Definitions.
(2) Enter the user ID and then press the "Key”
icon (Figure 2 on the right) to enter password
verification mode. If the prompt “Unregistered
user!” is displayed, the user ID is nonexistent
or the user ID bearer has not enrolled his/her
password in the system.
(3) Enter the password and press the “OK”
icon to start the password comparison, as
shown in Figure 3 on the right.
(4). If the verification is successful, an interface
as shown in Figure 4 on the right will be
displayed.
14
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1.8.4 ID Card Verification
Only the products with a built-in ID card module support the ID card verification. The
products with a built-in ID card module support the following two verification modes:
ID Card Only: Users only need to swipe their ID cards for verification.
ID + Facial Verification: After passing the ID card verification, you also need to
perform facial verification.
For the settings of these two verification modes, see 5.5 Log Settings.
1.
ID Card Only
(1) If you have your ID card number enrolled
in the system, you can pass the verification
by swiping your ID card at the swiping area
in a proper way.
(2) If the verification is successful, an
interface as shown in Figure 1 on the right
will be displayed.
(3) If the verification is not successful, an
interface as shown in Figure 2 on the right
will be displayed.
15
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
2.
ID + Facial Verification
(1) Swipe your ID card properly at the
swiping
area
to
enter
the
1:1
facial
verification mode, as shown in Figure 1 on
the right:
(2) Compare the facial in a proper way. For
details, see 1.1 The Distance, Facial
Expression and Stand Pose.
(3) If the verification is successful, an
interface as shown in Figure 3 on the right
will be displayed. The system will return to
the main interface if the verification is not
passed within 20 seconds.
16
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
2. Main Menu
There are two types of rights respectively granted to two types of users: the ordinary
users and administrators. Ordinary users are only granted the rights of facial,
fingerprint, password or card verification, while administrators are granted the
access to the main menu for various operations apart from having all the privileges
granted to ordinary users.
Press [Menu] on the initial interface to access the main menu, as shown in the
following figure:
Any user can access the main menu by pressing the [Menu] key if the
system is free from administrators. After administrators are configured
on the terminal, the terminal needs to verify the administrators’ identity
before granting them access to the main menu. To ensure terminal
security, it is recommended to set an administrator when using the
terminal initially. For detailed operations, see 3.1.9 Modify User
Rights.
17
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
The main menu includes ten submenus and three shortcut keys, as shown in the
following figure:
Return to Initial Interface
Add a User
Set Date/Time
System Information
User Mgt.: Through this submenu, you can browse the user information stored on
the terminal, including the user ID, name, fingerprint, facial, card, password, rights;
add, modify or delete the user information.
Comm.: Through this submenu, you can set related parameters for communication
between the FFR terminal and PC, including the IP address, Gateway, Subnet Mask,
Baud Rate, Device ID and Comm Key and so on.
System: Through this submenu, you can set system-related parameters, including
the General, Display, Fingerprint, Face and Log Settings, to enable the FFR terminal
to meet user requirements to the greatest extent in terms of functions and display.
Data Mgt.: Through this submenu, you can perform management of data stored on
the FFR terminal, for example, Delete Transactions, All Data and Picture, Clear
Administrator and Restore to Factory Settings.
Dn/Upload: Through this submenu, you can import user information and attendance
data stored in a USB disk to related software or other fingerprint recognition
equipment.
18
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Keyboard: Through this submenu, you can customize six shortcut keys. Related
status will be displayed by pressing related status key.
Auto Test: This submenu enables the system to automatically test whether
functions of various modules are normal, including the Screen, Fingerprint, Voice,
Face, Keyboard and Time.
Calibration: When the touch screen is less sensitive to the touch, you can calibrate
the screen on the calibration interface through this submenu.
Bell: Through this submenu, you can set the alarm time and duration.
Access: Through this submenu, you can set the parameters of the electronic locks
and related access control devices.
☺
Note: When the user enable access, then you can make access setting,
otherwise can’t. For detail please see 5.2 Display.
19
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3. User Management
Browse the user information, including the user ID, name, fingerprint, FC (face), ID
card, password, rights. Add, edit or delete the basic information of users.
Press [User Mgt.] on the main menu interface to display the user management
interface.
①Return to the Menu interface
②Query a user
③Add a user
④Scroll bar
⑤User list area
⑥Character selection area
The user is an administrator.
The user has enrolled his/her fingerprint.
The user has enrolled his/her facial image.
The user has enrolled his/her ID card.
Note:
The user has enrolled his/her password.
(1) In User List Area, users are listed in alphabetical order by last name. If you
select a user in User List Area, you can access the editing interface of this user to
edit or delete related user information.
(2) In Character Selection Bar, users are listed in alphabetical order by last name or
by default and you can locate the desired user quickly. You can press [Query] to
locate and query a user through the user ID. For details, see 3.4 Querying a User.
20
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1. Adding a User
Press [Add] on the [User Mgt.] interface to display the [Add User] interface as
shown below.
User ID: Enter a user ID. 1- to 9-digit user IDs are supported by default.
Name: Enter a user name. 12-character user names are supported by default.
Fingerprint: Enroll a user’s fingerprint and the FFR terminal displays the number of
enrolled fingerprints. A user can enroll 10 fingerprints at maximum.
Face: Enroll a user’s face.
Password: Enroll a user’s password. 1- to 8-digit passwords are supported by default.
Group No.: Set the group that the user belongs to. Valid group No.: 1–24.
Note: When the user opens 1: G Verify function, then display the set item of Group
No., or not. For detail, please see 5.5 Log Settings.
Role: Set the rights of a user. A user is set to ordinary user by default and can also
be set to administrator. Ordinary users are only granted the rights of facial,
fingerprint card or password verification, while administrators are granted the access
to the main menu for various operations apart from having all the privileges granted
to ordinary users.
Card : Enroll a user card. The length is 10.
Photo: Enroll a user’s photo. During user verification, the user’s photo is displayed
on screen.
The ID card is an optional function. If you need this function, please
consult our commercial representatives or fore-sale technical support
personnel.
21
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.1 Entering a User ID
The FFR terminal automatically allocates an ID starting from 1 for every user in
sequence. If you use the ID allocated by the FFR terminal, you may skip this section.
1. Press [User ID] on the Add User interface to display the user ID management
interface, as shown in Figure 1 on the right:
Tip: The user ID can be modified during initial enrollment, but once enrolled, it
cannot be modified.
2. On the displayed keyboard interface, enter a
user ID and press <OK> as shown in Figure 2
on the right. If a prompt message “The user ID
already exists!” is displayed, enter another ID.
Tip: The FFR terminal supports 1- to 9-digit
user IDs by default. If you need to extend
the length of current user ID numbers,
please
consult
representatives
or
our
fore-sale
commercial
technical
support personnel.
3. After the user ID is entered, an interface is
displayed as show in Figure 3 on the right.
Press [Save] to save current information and
return to the previous interface. Press [User
Mgt.] to return to the previous interface without
saving current information.
22
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.2 Entering a Name
Enter a user name through the keyboard.
1. Press [Name] on the Add User interface to
display the name input interface, as show in
figure 1 on the right.
2. On the displayed keyboard interface, enter
a user name and press [Enter] as shown in
figure 2 on the right. For details of operations
on keyboard interface, see Appendix1 Text
Input Instructions.
Tip: The FFR terminal supports the 1- to
12-character names by default.
3. Press [X] to confirm, as shown in figure 3 on
the right.
4. After the user name is entered, the interface
is displayed as shown in figure 4 on the right.
Press [Save] to save current information and
return to the previous interface. Press [User
Mgt.] to return to the previous interface without
saving current information.
23
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.3 Enrolling a Fingerprint
1. Press [Fingerprint] on the Add User interface to display the Enroll Fingerprint
Interface, as shown in Figure 1 on the right.
2. On the displayed Enroll Fingerprint
Interface (as shown in the Figure 2 on the
right), place your finger on the fingerprint
collector properly according to the system
prompts. For details, see “Finger Placement”.
3. Place the same finger on the fingerprint
collector for three consecutive times correctly.
If the enrollment succeeds, the system will
display
a
prompt
message
“Enrolled
Successfully” and automatically return to the
[Add User] interface (as shown in Figure 3 and
4 on the right). If the enrollment fails, the
system will display a prompt message and
return to the [Enroll Fingerprint] interface. In
this case, you need to repeat the operations of
step 2.
4. You can back up the enrolled fingerprint of a
user by pressing [Fingerprint]. A user can
enroll 10 fingerprints at maximum.
5. Press [Save] to save current information and
return to the previous interface. Press [User
Mgt.] to return to the previous interface without saving current information.
24
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.4 Enrolling a Password
1. Press [Password] on the Add User
interface
to
display
the
password
management interface, as shown in Figure 1
on the right.
2. On the displayed keyboard interface, enter
a password and press <OK> as shown In
Figure 2 on the right. Re-enter the password
according to the system prompt and then
press <OK>.
Tip: The FFR terminal supports the 1- to
8-digit passwords by default.
3. After the password is entered, an interface
is displayed as shown in Figure 3 on the right.
Press [Save] to save current information and
return to the previous interface. Press [User
Mgt.] to return to the previous interface
without saving current information.
25
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.5 Enrolling a Face
1. Press [Face] on the Add User interface to
display the face enrollment interface, as
shown in Figure 1 on the right.
2. On the displayed face enrollment interface
(as shown in Figure 2 on the right). Eyes show
in the box according to the voice prompts. See
1.1 The Distance, Facial Expression and
Stand Pose.
3. If your facial image is enrolled successfully,
the system will display a prompt message and
automatically return to the Add User interface
(as shown in Figure 3 on the right).
4. Press [Save] to save current information
and return to the previous interface. Press [User Mgt.] to return to the previous
interface without saving current information.
26
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.6 Entering a Group No.
The FFR terminal enables the facial comparison function by default. During face
enrollment, the FFR automatically allocates a group No. starting from 1 for every
user in sequence. When the number of users in Group No.1 reaches the upper limit,
the rest users fall under Group No.2 automatically. Up to 100 facial images can be
enrolled in Group No.1 and only 50 facial images can be enrolled in other groups. If
you use the group No. allocated by the FFR terminal, you may skip this section.
1. Press [Group No.] on the [Add User]
interface to display the group No. management
interface, as shown in figure 1 on the right.
2. On the displayed keyboard interface, enter
your group No. and press <OK> as shown in
figure 2 on the right.
Tip: A valid group No. contains 1–5 digits.
3.
After the group No. is entered, an interface
is displayed as shown in figure 3 on the right.
Press [Save] to save current information and
return to the previous interface. Press [User
Mgt.] to return to the previous interface without
saving current information.
Tip: Please remember your own group No.
27
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.7 Enrolling an ID Card
1. Press [Card] on the Add User interface to
display the [Enroll Card] interface, as shown
in Figure 1 on the right.
2. The [Punch Card!] interface pops out as
shown in Figure 2 on the right. Swipe your ID
card properly in the swiping area. For details,
see “1.6 Appearance of the FFR Terminal”.
3. If the card passes the verification, the FFR
terminal displays a prompt message “Read
Successfully! Card No.: **********”, as shown
in Figure 3 on the right, and returns to the
[Add User] interface. Press [Card] to display
the enrolled card number as shown in Figure 4
on the right.
4. Press [Save] to save current information
and return to the previous interface. Press
[User Mgt.] to return to the previous interface
without saving current information.
28
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.8 Enrolling an Mifare Card
The 4.3 inches Facial & Fingerprint Recognition Series Products only favors Mifare
card's being an ID card use. Use step and ID card to register an operation to accord.
Note:Mifare card is an option function on the fingerprint machine, if you want
to customize the fingerprint machine with Mifare card function, please
contacts our market supporter and salesman.
3.1.9 Modify User Rights
1. On the Add User interface, press [Role:
User] to change the user as an administrator,
as shown in Figure 1 on the right.
Note: There are two types of rights
respectively granted to two types of users:
the User and Administrator. User are only
granted the rights of facial, fingerprint, or
password verification, while Administrator
are granted the access to the main menu
for various operations apart from having all
the privileges granted to User.
2. After the modification is done, the interface
is as shown in Figure 2 on the right. Press [Save] to save current information and
return to previous interface; press [User Mgt.] to directly return to previous interface
without saving current information.
29
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.1.10 Enroll Photo
If you have enrolled your photo in the system, the system will display your enrolled
photo in addition to your ID and name after you pass the verification.
1. Press [Photo] on the [Add User] interface to
display the photo enrollment interface, as
shown in Figure 1 on the right.
2. On the photo enrollment interface, stand
naturally in front of the screen. For details, see
1.1 Standing Position and Posture, and Facial
Expression. Press [Capture] as shown in
figure 2 on the right to display the photo taken
at the lower left corner. The successful capture
interface is shown as figure 3 on the right.
3. After taking the photo, press [Exit] to return
to previous interface.
4. After the photo is taken, the interface is as
shown in Figure 4 on the right. Press [Save] to
save current information and return to previous
interface; press [User Mgt.] to directly return to
previous interface without saving current
information.
30
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.2 Edit a User
Select a user from the User List to enter User Info interface.
The User ID cannot be modified, and the other operations are similar to those
performed to add a user. You can re-enroll your fingerprint and facial image, change
your password and modify the management rights (Role).
31
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.3 Delete a User
On the [User Info] interface, you can delete all or partial user information.
1. Press [Delete] to delete a user, as shown
below.
2. On the interface displayed (show as below),
click [YES] to delete current user or [NO] to
return to previous interface.
32
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.4 Query a User
To facilitate administrators to locate a user quickly from a large number of enrolled
users, the FFR terminal enables user query by his/her “User ID” and “Name”.
(Location Search)
3.4.1 Query by User ID
1. Press [Query] on the [User Management]
interface to display the User ID query
interface, as shown in Figure 1 on the right.
2. Enter the user ID on the displayed interface,
and click [OK] (as shown in Figure 2 on the
right) to locate the cursor to the desired user
(as shown in Figure 3 on the right).
33
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3.4.2 Query by Name
On the [User Mgt.] interface, enter the user name through the “Character Selection
Bar” to locate the cursor to the desired user, as shown in the following figure:
By selecting a character from the “Character Selection Bar”, you can quickly locate
the users whose names start with this character. Users are listed in alphabetical
order by last name by default.
34
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
4. Communication-related Settings
You can set related parameters for the communication between the FFR terminal
and PC, including the IP Address, Gateway, Subnet Mask, Baud Rate, Device ID,
and Comm Key.
4.1 Network Settings
When the FFR terminal communicates with the PC over Ethernet, you need to check
the following settings:
IP Address: The IP address is 192.168.1.201 by default and can be changed as
required.
Subnet Mask: The subnet mask is 255.255.255.0 by default and can be changed as
required.
35
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Gateway: The gateway is 0.0.0.0 by default and can be changed as required.
DNS Server: The DNS Server is 0.0.0.0 by default and can be changed as required.
Device ID: This parameter is used to set the ID of device from 1 to 254. If the
RS232/RS485 communication is adopted, you need to enter the device ID on the
software communication interface.
Comm Key: To enhance the security of attendance data, you can set a password for
the connection between the FFR terminal and PC. Once the password is set, you
can connect the PC with the FFR terminal to access the attendance data only after
entering the correct password. The default password is 0 (that is, no password).
Once a password is set, you need to enter this password before connecting the PC
software with the FFR terminal; otherwise, the connection is unsuccessful. 1- to
6-digit passwords are supported.
36
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
4.2 Serial Port Settings
When the FFR terminal communicates with the PC over serial ports (RS232/RS485),
you need to check the following settings:
RS232: This parameter is used to enable or disable the RS232 communication. If
the RS232 communication cables are used, set this parameter to “ON”.
RS485: This parameter is used to enable or disable the RS485 communication. If
the RS485 communication cables are used, set this parameter to “ON”.
Baud Rate: This parameter is used to set the baud rate for the communication
between the FFR terminal and the PC. It includes five options: 9600, 19200, 38400,
57600, and 115200. The high baud rate is recommended for the RS232
communication to achieve high communication speed, while the low baud rate is
recommended for the RS485 communication to achieve stable low-speed
communication.
Considering the massive data including the fingerprint and facial
templates stored in the FFR terminal, it is recommended to transfer the
data between the FFR terminal and PC over network to enhance the
transfer speed.
37
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
4.3 WIFI Option
Before the device is used for wireless network, other physical groupware of 802.11
network, such as joint, distributing system, wireless medium must be in existence.
ESSID to connect to the network must be known (SSID).
SSID: SSID to be connected to wireless network. (There is difference between small
letter and capital letter.)
Network Type: there are two models: infrastructure model (for star structure) and ad
-hoc model (for peer-to-peer-network).
Auth mode: Infrastructure mode (Infra) includes five authentication modes: OPEN,
SHARED, WEPAUTO, WPAPSK and WPA2PS002E.
Ad-hoc model (Adhoc) includes four authentication modes: OPEN, SHARED,
WEPAUTO and WPANONE.
Encrypt Mode: When the selected encrypt type is NONE, the password in WEP
(Wired equivalent privacy) and WPA (WiFi protested access) cannot be edited,
namely, it is not necessary to input password.
IP address: In 802.11 wireless networks, there is DHCP. Or enter IP interface to
input correct IP address, subnet mask and so on.
Operation
Press the button after SSID item, input the value, which must be input, or the cursor
cannot be moved to other input box. Then press
press OK to do corresponding operation.
38
to select the item to be set or
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1)set password
According to the selected authentication mode and different encrypt types; the
interface where password is set is also different. There are two interfaces: WEP and
WPA.
WEP password:
As shown in Figure 1 on the right. Input the
password according to the requirement.
There are four group passwords in WEP
Password. If the 4 group passwords are set
and correct, then only the currently selected password is the valid value.
WPA password:
As shown in Figure 2 on the right. According
to the screen prompts 8-64 ASCII characters
or 16 hexadecimal numbers. After the
completion of installation click [save] button
to save, and returns to the upper interface
2)Point IP
Show as in Figure 3 on the right Point the
device IP in wireless network. It has nothing
to do with network option in communication
option.
After IP is specified, press
wireless option interface.
After setting, press
button to save the setting, and then return to
button to return to the upper interface.
39
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
4.4 Wiegand Output
Wiegand Format: The system has two built-in formats Wiegand 26-bits and
Wiegand 34-bits, and also supports the format customization function to meet
individualized requirements.
Failed ID: refers to the value output by the system upon verification failure. The
output format is subject to the setting of “Wiegand Format”. The default value scope
of Failed ID is 0–65535.
Site Code: The site code is used for customized Wiegand format. The site code is
similar to the device ID, but the site code is customizable and can be duplicated
among different devices. The default value scope of the site code is 0–255.
Pulse Width: refers to the width of the Wiegand pulse in microseconds. The default
value scope of the pulse width is 1–1000.
Pulse Interval: refers to the interval of the Wiegand pulse in microseconds. The
default value scope of the pulse width is 1–10000.
Output: refers to the contents output upon successful verification. You can select the
“User ID” or “Card Number” as the output.
4.4.1 Wiegand 26-bits Output Description
The system has a built-in Wiegand 26-bits format. Press [Wiegand Format], and
select “Standard Wiegand 26-bits”.
40
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
The composition of the Wiegand 26-bits format contains 2 parity bits and 24 bits for
output contents (“User ID” or “Card Number”). The binary code of 24-bits represent
up to 16,777,216 (0–16,777,215) different values.
1
2
Even parity
25 26
User ID/Card Number
Odd parity bit
Definition of Fields:
Field
Meaning
Even parity bit
Judged from bit 2 to bit 13. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
even parity bit is 1.
User
ID/Card
User ID/Card Number (Card Code, 0–16777215)
Number (bit 2-bit 25)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 14 to bit 25. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the odd
parity bit is 0.
For example, for a user with user ID of 12345, the enrolled card number is
0013378512 and the failed ID is set to 1.
1) When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
00000000000110000001110011
Even parity bit
User ID = Binary code of 12345
41
Odd parity bit
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
2) When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
11100110000100011110100000
Even parity bit User ID = Binary code of 0013378512
Odd parity bit
3) The Wiegand output is as follows upon verification failure:
00000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
Note: If the output contents exceed the scope allowed for the Wiegand format,
the last several bits will be adopted and first several bits are automatically
discarded. For example, the user ID 888 888 888 is 110 100 111 110 110 101 111
000 111 000 in binary format. Wiegand26 only supports 24 bits, that is, it only
outputs the last 24 bits, and first 6 bits “110 100” are automatically discarded.
4.4.2 Wiegand 34-bits Output Description
The system has a built-in Wiegand 34-bits format. Press [Wiegand Format], and
select “Standard Wiegand 34-bits”.
The composition of the Wiegand 34-bits format contains 2 parity bits and 32 bits for
output contents (“User ID” or “Card Number”). The binary code of 32-bits represent
up to 4,294,967,296 (0–4,294,967,295) different values.
42
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1
2
33 34
Even
User ID/Card Number
Odd parity bit
Table 2 Definition of Fields
Field
Meaning
Even parity bit
Judged from bit 2 to bit 17. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
even parity bit is 1.
User
ID/Card
User ID/Card Number (Card Code, 0–4,294,967,295)
Number (bit 2-bit 33)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 18 to bit 33. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
odd parity bit is 0.
For example, for a user with user ID of 123456789, the enrolled card number is
0013378512 and the failed ID is set to 1.
1) When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
0000001110101101111001101000101011
Even parity bit
User ID = Binary code of 123456789
Odd parity bit
2) When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
0000000001100110000100011110100001
Even parity bit
User ID = Binary code of 0013378512
43
Odd parity bit
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3) The Wiegand output is as follows upon verification failure:
0000000000000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
4.4.3 Customized Format
Apart from the two built-in formats Wiegand 26-bits and Wiegand 34-bits, the
system also supports the format customization function to meet individualized
requirements.
The customized format consists of two character strings: the data bits and parity
bits. These two character strings need to be defined separately. Data bits define the
number of binary bits output by Wiegand as well as the meaning of each bit. The
data bits output by Wiegand can be a card number (C), site code (s), facility code (f),
manufacturer code (m) and parity bits (p). Parity bits define the check mode of each
bit in data bits and ensure the correctness of data bits during transfer through the
parity check. The parity bits can be set to odd check (o), even check (e) and both
odd check and even check (b). There exists a one-to-one correspondence
relationship between the data bits and parity bits.
For example, the Wiegand26 can be customized as follows:
Definition of data bits: pssssssssccccccccccccccccp
Definition of parity bits: eeeeeeeeeeeeeooooooooooooo
Note: Wiegand26 consists of 26 bits. The first bit is the even parity bit of bits 2
to 13; the 26th bit is the odd parity bit of bits 14 to 25; the second to the ninth
bits are the site code; the 10th to the 25th bits are the card number.
For details about the Wiegand protocol, see Appendix 3 Introduction to Wiegand.
To customize Wiegand format, proceed as follows:
1) Select [Define Format] and the [Set] key is then enabled.
2) Press [Set] to display the [User Define Format] interface, as shown in the
following figure:
44
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
3) Click the entry box below “Card Format” to display the following interface:
Display input in real-time
Backspace
Display the number of
bits in real-time
Cancel Input
Confirm Input
Clear Input
Characters used to define data bits and their meanings:
c: indicates the card number, that is, the output contents, it can be set to User
ID/Card Number through menu operations.
f: indicates the facility code which is 0 by default. It is not configurable. To modify it,
please contact the equipment supplier.
m: indicates the manufacturer code which is 0 by default. It is not configurable. To
modify it, please contact the equipment supplier.
p: indicates the parity position.
s: indicates the site code which can be set from 0 to 255 by default.
45
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
4) Click the entry box below “Parity Format” to display the following interface:
Characters used to define parity bits and their meanings:
o: indicates the odd check, that is, there is an odd number of 1’s in the bit sequence
(including one parity bit). For example, for 1000110(0), the parity bit is 0 and there
are already three 1’s. After 0 is suffixed to 1000110, there is still an odd number of
1’s.
e: indicates the even check, that is, there is an even number of 1’s in the bit
sequence (including one parity bit). For example, for 1000110(1), the parity bit is 1
and there are already three 1’s. After 1 is suffixed to 1000110, there is an even
number of 1’s.
b: indicates both odd check and even check.
For example: Definitions of several universal Wiegand formats.
Wiegand34
Data bits: pccccccccccccccccccccccccccccccccp
Parity bits: eeeeeeeeeeeeeeeeeooooooooooooooooo
Note: Wiegand34 consists of 34 bits. The first bit is the even parity bit of bits 2
to 17; the 34th bit is the odd parity bit of bits 18 to 33; the second to the ninth
bits are the site code; the 10th to the 25th bits are the card number.
46
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Wiegand37a
Data bits: pmmmmsssssssssssscccccccccccccccccccp
Parity bits: oeobeobeobeobeobeobeobeobeobeobeobeoe
Note: Wiegand37a consists of 37 bits. The first bit is the odd parity bit of bits 3, 4, 6,
7, 9, 10, 12, 13, 15, 16, 18, 19, 21, 22, 24, 25, 27, 28, 30, 31, 33, 34 and 36; the 37th
bit is the odd parity bit of bits 2, 4, 5, 7, 8, 10, 11, 13, 14, 16, 17, 19, 20, 22, 23, 25,
26, 28, 29, 31, 32, 34 and 35; bits 4, 7, 10, 13, 16, 19, 22, 25, 28, 31 and 34
participate in both odd and even parity check. Bits 2 to 5 are manufacturer code; bits
6 to 17 are the site code; bits 18 to 36 are the card number.
Wiegand37
Data bits: pmmmffffffffffssssssccccccccccccccccp
Parity bits: eeeeeeeeeeeeeeeeeeooooooooooooooooooo
Note: Wiegand37 consists of 37 bits. The first bit is the even parity bit of bits 2 to 18;
the 34th bit is the odd parity bit of bits 19 to 36; the second to the fourth bits are the
manufacturer code; the 5th to the 14th bits are facilitate code; the 15th to the 20th bits
are the site code; the 21st to the 36th bits are the card number.
Wiegand50
Data bits: pssssssssssssssssccccccccccccccccccccccccccccccccp
Parity bits: eeeeeeeeeeeeeeeeeeeeeeeeeooooooooooooooooooooooooo
Note: Wiegand50 consists of 50 bits. The first bit is the even parity bit of bits 2 to 25;
th
th
the 50 bit is the odd parity bit of bits 26 to 49; the second to the 16 bits are the site
code; the 17th to the 49th bits are the card number.
47
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
5. System Configuration
Through the System menu, you can set system-related parameters, including the
General parameter, Display parameter, Fingerprint parameter, Face and Log
Settings parameter and so on, to enable the terminal to meet user requirements to
the greatest extent in terms of functions and display.
5.1 General
Date/Time: This parameter is used to set the date and time of the FFR terminal.
Date Format: This parameter is used to set the format of the date displayed on the
initial interface of the FFR terminal.
Keyboard Clicks: This parameter is used to set whether to generate beep sound in
response to every keyboard touch. Select “ON” to enable the beep sound, and select
“OFF” to mute.
Voice Prompts: This parameter is used to set whether to play voice prompts during
the operation of the FFR terminal. Select “ON” to enable the voice prompt, and
48
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
select “OFF” to mute.
Volume (%): This parameter is used to adjust the volume of voice prompts.
Lock Power Key: This parameter is used to set whether to lock the power key.
Select “ON” to disable the power key. If you select “OFF” and press the power key,
the FFR terminal will be shut down in three seconds.
5.2 Display
Language: This parameter is used to display the current language used by the FFR
terminal. For multilingual-capable FFR terminals, you can switch between different
languages through this parameter.
24-Hour Time: This parameter is used to set the time display mode of the initial
interface. Select “ON” to adopt the 24-hour display mode. Select “OFF” to adopt the
12-hour display mode.
Toolbar: This parameter is used to display style of the shortcut keys on the initial
interface. It can be set to “Auto Hide” and “Unhide”. By selecting “Auto Hide”, you
can manually display or hide the toolbar. By selecting “Unhide”, you can
permanently display the toolbar on the initial interface.
Picture Delay (S): This parameter is used to set the picture cycle interval, the
default value is 0 (means not enable this function).
The value scope: 3─999
seconds).
Sleep Time (S): This parameter is used to specify a period after which the FFR
terminal is put in sleep mode if not operated within this period. You can bring up the
FFR terminal from sleep by pressing any key or touching the screen.
49
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Enable access: Sets whether to enable access control settings can choose yes or
no, choice yes is open, or closed.
5.3 Fingerprint
1: 1 Threshold: This parameter is used to set the threshold of matching between
current fingerprint and the fingerprint template enrolled in the FFR terminal in the 1:1
verification mode. If the similarity between current fingerprint and the fingerprint
template enrolled in the FFR terminal is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
1: N Threshold: This parameter is used to set the threshold of matching between
current fingerprint and the fingerprint template enrolled in the FFR terminal in the 1:N
verification mode. If the similarity between current fingerprint and the fingerprint
template enrolled in the FFR terminal is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
The recommended thresholds are as follows:
Threshold
(FRR)
(FAR)
1: N
1:1
High
Low
45
25
Medium
Medium
35
15
Low
High
25
10
50
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
1:1 Retry Times: This parameter is used to set the retry times in the event of failure
of 1:1 verification or password verification due to absence of fingerprint enrollment or
improper finger placement, so as to avoid repetitive operations.
Algorithm Version: This parameter is used to select the fingerprint algorithm
version between 9.0 and 10.0. Please select the algorithm version with caution
because the fingerprint templates of these two algorithm versions are incompatible.
Fingerprint Image: This parameter is used to set whether to display the fingerprint
image on the screen during fingerprint enrollment or comparison. It has two values:
Permanent Display and No Display.
5.4 Face
1: 1 Threshold: This parameter is used to set the threshold of matching between
current face and the facial template enrolled in the FFR terminal in the 1:1
verification mode. If the similarity between current face and the facial template
enrolled in the FFR terminal is larger than this threshold, the matching is successful;
otherwise, the matching is not successful. The valid value scope is 70-120. The
higher the threshold, the lower the FAR and the higher the FRR, and vice versa.
1:1: N Threshold: This parameter is used to set the threshold of matching between
current face and the facial template enrolled in the FFR terminal in the 1: N
verification mode. If the similarity between current face and the facial template
enrolled in the FFR terminal is larger than this threshold, the matching is successful;
otherwise, the matching is not successful. The valid value scope is 80-120. The
higher the threshold, the lower the FAR and the higher the FRR, and vice versa.
51
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
The recommended thresholds are as follows:
FRR
High
Medium
Low
FAR
Low
Threshold
1: N
1:1
85
80
Medium
82
75
High
80
70
Exposure: This parameter is used to set the exposure value of the camera. The
default value is 300.
Quality: This parameter is used to set a quality threshold for the facial images
obtained. The FFR terminal accepts the facial images and processes them by
adopting the facial algorithm when their quality is higher than the threshold;
otherwise, it filters these facial images.
Note: Improper adjustment of the Exposure and Quality parameters may
severely affect the performance of the FFR terminal. Please adjust the
Exposure parameter only under the guidance of the after-sales service
personnel from our company.
5.5 Log Settings
Log Alert: When the available space is insufficient to store the specified number of
attendance records, the FFR terminal will automatically generate an alarm. (Value
scope: 1─99)
Dup. Punch Period (m): If a user’s attendance record already exists and the user
punches in again within the specified period (unit: minute), his/her second
52
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
attendance record will not be stored. (Value scope: 1─60 minutes)
Workcode Mode: This parameter is used to select the work code input mode among
Mode 1, Mode 2 and None during attendance verification. If you select Mode 1, the
attendance verification starts after you input the work code on the initial interface; if
you select Mode 2, the attendance verification starts before you input the work code
on the initial interface; if you select None, you do not need to input the work code
during attendance verification on the initial interface. For the input of the work code,
see 6.2 Work Code.
Card Only: If this parameter is set to “YES”, you pass the verification only after card
verification. If this parameter is set to “NO”, you need to verify your face or fingerprint
after card verification.
Face detect interval [s]: According to the need to set the same person face detect
interval time. The default is 0, namely without interval.
1: G Verify: To set enable or close 1: G Verify function.
53
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
5.6 Update
You can upgrade the firmware program of the FFR terminal by using the upgrade file
in the USB disk through this parameter.
If you need the firmware upgrade file, please contact our
technical support personnel. Generally the firmware upgrade is
not recommended.
54
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
6. Data Management
Through the [Data Mgt.] menu, you can perform management of data stored on the
FFR terminal, for example, deleting the attendance record, all data and promotional
pictures, purging management rights and resetting the FFR terminal to factory
defaults.
Delete Transactions: Delete all the attendance records.
Delete All Data: Delete all the information of enrolled personnel, including their
fingerprints, facial images and attendance records.
Clear Administrator: Change all administrators to ordinary users.
Delete Picture: Purge the promotional pictures uploaded from USB disks to the FFR
terminal. (For details on how to upload promotional pictures, see “5.4 Upload
Picture”.)
Restore to Factory Settings: Restore all parameter settings on the FFR terminal to
factory settings.
Record: Query the attendance records of employees within a specified time range.
WorkCode: Add, edit or delete the work codes of employees.
The employee information and attendance records will
not be deleted during restoration to factory settings.
55
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
6.1 Query a Record
After check-in successfully, the employee’s attendance records are saved in the FFR
terminal. You can easily query these attendance records.
User ID: Enter the user ID of the employee to query. If this field is left blank, you can
query the attendance records of all the employees. If you enter a user ID, you can
query the attendance record of the employee with this user ID.
Query Time Period: Select a time period to
query, including the customized time period,
yesterday, this week, last week, this month,
last month, and all time periods.
Start
and
End:
When
you
select
a
customized time period, you need to input a
start time and an end time. When you select
other options for time period, the start and
end time will be automatically adjusted to the
related time.
After setting the query conditions, press
[Query] and the records that meet the
specified query conditions will be displayed
on screen. As shown in Figure 2 on the right.
Select the row where the desired record is
located,
you
can
query
the
detailed
information of this record, for example, the
detailed attendance record of the employee
with user ID 10001 on November 14, 2011.
As shown in Figure 3 on the right.
56
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
6.2 Work Code
Employees’ salaries are subject to their attendance records. Employees may be
engaged in different types of work which may vary with time periods. Considering the
salaries vary with work types, the FFR terminal provides a parameter to indicate the
corresponding work type for every attendance record to facilitate rapid
understanding of different attendance situations during the handling of attendance
data.
1.
Add a work code
(1) Press [Add] on the WorkCode interface
(as shown in Figure 1 on the right) to display
the [Add] interface.
No.: A digital code of the work code.
Label: The meaning of the work code.
(2) Press the corresponding entry button of
[No.] on the [Add] interface (as shown in
Figure 2 on the right) to display the No. entry
interface. On this interface, enter a No.
(3) Press the corresponding entry button of
[Label] on the WorkCode interface (as
shown in Figure 3 on the right) to display the
text entry interface. On this interface, enter a
label of work code. (See Appendix 1 Text
Input Instructions)
57
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
2.
Edit and delete a work code
(1) Press the row of a work code on the
WorkCode interface (as shown in Figure 1
on the right) to display the [Edit] interface.
(2) To edit this work code, enter a new No.
and label with the same operation steps as
described in “Add a work code”.
(3) To delete this work code, press [Delete]
(as shown in Figure 3 on the right).
(4) On the displayed prompt interface, press
<YES> to confirm the deletion of this work
code, and press <NO> to cancel the deletion
operation (as shown in Figure 4 on the right).
58
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
7. USB Disk Management
Through the [Dn/Upload] menu, you can import user information and attendance data
stored in a USB disk to related software or other fingerprint recognition equipment.
Download Transactions: Import all the attendance data from the FFR terminal to a USB
disk.
Download User: Import all the user information, fingerprints and facial images from the
FFR terminal to a USB disk.
Download user photos: Import the employees’ photos from the FFR terminal to a USB
disk.
Upload User: Upload the user information, fingerprints and facial images stored in a USB
disk to the FFR terminal.
Upload Picture: Upload the JPG documents with “ad_” as initial letters of document
names stored in a USB disk to the FFR terminal. After the upload, these pictures can be
displayed on the initial interface of the FFR terminal. (For details on picture specifications,
see Appendix 2.)
Upload User Photo: Upload the JPG named with user ID in the USB disk to the FFR
terminal. After the upload, when display the photo after the user successful verification.
For detail, please see Appendix 6 Photo ID function.
59
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
8. Keyboard Definitions
You can define six shortcut keys as attendance status shortcut keys or functional
shortcut keys. On the main interface of the FFR terminal, press corresponding keys
and the attendance status will be displayed or the function interface will be rapidly
displayed.
1. Press [Keyboard] on the main menu
interface to display the [Keyboard] interface,
as shown in Figure 1 on the right.
2. All the defined shortcut keys and their
functions are listed on the Keyboard interface
(as shown in Figure 2 on the right). Press a
shortcut key in the list to display the shortcut
key editing interface.
3. Edit the functional introduction of interface
Key: Options include: F1–F6.
Note: When the FFR terminal supports both
fingerprint and face recognition modes, F6
is defined as a recognition mode switch
key by default and cannot be modified.
Function: You can set the functions of
different shortcut keys, such as Status, 1:1/1:
G, Work code, Face G1 to G5 and Undefine.
1:1: Set the verification type as 1:1, as shown in Figure 3 on the right.
Label:
Include
Check-In,
Check-Out,
60
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Break-Out, Break-In, OT-In, 0T-Out. The setting interface is shown in Figure 1on the
right.
When setting the attendance status shortcut keys, you can also set the “Auto Switch”
parameter. When “Auto Switch” is enabled, the FFR terminal automatically switches
the attendance status at the specified time. The “Auto Switch” setting interface is as
shown in Figure 2 on the right.
The (work code) shortcut key setting interface is as shown in Figure 3on the right.
61
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
9 Auto Test
The auto test enables the system to automatically test whether functions of various
modules are normal, including the screen, collector, voice, facial, keyboard and
clock tests.
Screen Test: The FFR terminal automatically tests the display effect of the color
TFT display by displaying full color, pure white and pure black and checks whether
the screen displays properly. You can continue the test by touching the screen or
exit it by pressing [Auto Test].
Voice Test: The FFR terminal automatically tests whether the voice files are
complete and the voice quality is good by playing the voice files stored in the
terminal. You can continue the test by touching the screen or exit it by pressing [Auto
Test].
Keyboard Test: The FFR terminal tests whether every key on the keyboard works
normally. Press any key on the [Keyboard Test] interface to check whether the
pressed key matches the key displayed on screen. The keys are dark-gray before
pressed, and turn blue after pressed. Press [Auto Test] to exit the test.
Fingerprint Test: The FFR terminal automatically tests whether the fingerprint
collector works properly by checking whether the fingerprint images are clear and
acceptable. When the user places his/her finger in the fingered guide, the collected
fingerprint image is displayed on the screen in real-time. Press [Auto Test] to exit
62
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
the test.
Face Test: The FFR terminal automatically tests whether the camera works properly
by checking whether the collected facial images are clear and acceptable. Press
[Auto Test] to exit the test.
Time Test: The FFR terminal tests whether its clock works properly by checking the
stopwatch of the clock. Touch the screen to start counting, and touch it again to stop
to check whether the counting is accurate. Press [Auto Test] to exit the test.
63
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
10 Screen Calibration
You can perform all the menu operations by touching the screen with one of your
fingers or a touch pen. When the touch screen is less sensitive to the touch, you can
perform screen calibration through menu operations.
1. Press [Menu] on the initial interface to
display the main menu interface.
2. Press [Calibration] on the main menu
interface to display the screen calibration
interface.
3. Touch the center of the cross “+”.
4. Repeat Step 3 following the move of the
“+” icon to different locations on the screen.
5. Touch the center of the cross at five
locations on the screen correctly. When the
message “Calibrating screen, pls wait……” is
displayed
on
screen,
the
calibration
succeeds and the system automatically
returns to the main menu. If the calibration
fails, the system will request recalibration
starting from Step 3.
64
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
11 Bell Setting
Lots of companies need to ring their bells to signal the start and end of work shifts,
and they usually manually ring their bells or use electric bells. To lower costs and
facilitate management, we integrate the time bell function into the FFR terminal. You
can set the alarm time and duration for ringing the bell based on your requirements,
so that the FFR terminal will automatically play the selected ring tone and triggers
the relay at the alarm time, and stop playing the ring tone after the set duration.
Press [Bell] on the main menu interface to
display the bell setting interface, as shown in
Figure 1 on the right.
1. Add a bell
(1) The displayed bell setting interface (as
shown in Figure 2 on the right) lists all the
bells. Click [Add] to display the [Add]
interface. As shown in Figure 3 on the right.
Note: You only can add 15 bells.
(2) On the [Add] interface, set the following
parameters:
Bell Time: This parameter is used to set a
time
point
when
the
FFR
terminal
automatically plays a bell ring tone everyday.
Ring Tone: This parameter is used to set the
bell ring tone.
Repeat: This parameter is used to set the alarm times.
State: This parameter is used to set whether to enable the bell.
65
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Bell Type: You can select between internal ringing, external ringing or Int&Ext Bell.
For internal ringing, the ring tone is played by the loudspeaker of the FFR terminal.
For external ringing, the ring tone is played by an external electric bell that is wired
with the FFR terminal.
Notice: Only some machines have external ringing options.
The alarm sounds of the bell and the access control cannot be
concurrently generated by the loudspeaker of the FFR terminal or
externally connected relay. Therefore, when the bell is set to the
external ringing mode, the access limit alarm will automatically
change to the internal ringing mode, and vice versa.
2. Edit and delete a bell
Press a bell in the list on the bell setting
interface to display the Edit interface, with
the similar operation as “Add a bell”.
Press [Delete] on the Edit interface and the
system displays a prompt window as shown
in the figure on the right. In the prompt
window, press <YES> to delete the current
bell and <NO> to cancel the deletion.
66
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
12 Access Control Setting
Through the [Access] menu, you can set the parameters of the electronic locks and
related access control devices.
Lock [s]: Fingerprint scanner controls the time to open electronic lock.
(Functioning value for 1~10)
Door Sensor Delay[s]: Some segment time which begin after open door just begin
alarm; (The functioning value is 1~99)
Door Sensor Mode: There are three option that is none( NONE), normal open (NO),
normal close(NC). The none means the door Sensor doesn’t apply, Normal Open is
defined that Thee door can be set to a Passage Mode in the normal condition,
Normal Close means that the door is close in the normal work condition.
Door Sensor Alarm Delay [s]: Detection to the abnormal door sensor state, the
door sensor will generate an alarm signal after a period of time; this time is door
sensor alarm delay. (The functioning value is 1 ~ 99)
☺
Note: Only the user has enable access function, you can make access control
setting, otherwise can’t. For detail, please see 5.2 Display.
67
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
13 Date/Time Setting
13.1 Set Date/Time
The date and time of the FFR terminal must be set accurately to ensure the accuracy
of attendance time.
1. Press [Menu] on the initial interface to
display the main menu interface.
2. Press [Time/Date] on the main menu
interface to display the time setting interface.
3. Select the desired date and time by pressing
the numbers on the screen, or enter the related
values into the date and time entry boxes
through the keyboard (as shown in Figures 3
and 4 on the right).
4. Press [Save] to save current information and
return to the previous interface. Press [Cancel]
to return to the previous interface without
saving current information.
68
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
13.2 Set Daylight Saving Time (DLST)
The Daylight Saving Time (DLST) is a widely used system of adjusting the official
local time forward to save energy. The uniform time adopted during the
implementation of this system is known as the DLST. Typically clocks are adjusted
forward one hour in the summer to make people early to bed and early to rise so as
to make full use of illumination resources and save electricity. Clocks are adjusted
backward in autumn. The specific DLST regulations vary with countries.
To meet the DLST requirement, the FFR
terminal supports the DLST function to adjust
forward on hour at ×× (Hour): ×× (Minute) ××
(Day) ×× (Month) and backward one hour at
×× (Hour): ×× (Minute) ×× (Day) ×× (Month).
1. Press [Menu] on the initial interface to
display the main menu interface.
2. Press [Time/Date] on the main menu
interface to display the time setting interface.
As shown in Figure 1 on the right.
3. Press [DLST] on the time setting interface to
display the DLST setting interface. As shown
in Figure 2 on the right.
4. Set the following parameters on the DLST
setting interface, as show in figure 3 on the
right.
DLST Settings: This parameter is used to
enable or disable the DLST.
69
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Mode: You can select between Mode 1 and Mode 2. In Mode 1 (the default mode),
the DLST is set in the “Month-Day Hour: Minute” format; in Mode 2, the DLST is set
in the “Month-Week-Day Hour: Minute” format. As shown in Figure 1 on the right.
The value scope of week (WS): 1 – 6. 1 means the first week, 2 the second week
and so on and so forth. The value scope of
day (WK): 0 – 6. 0 means Sunday, 1 means
Monday and so on and so forth.
Start and End: These two parameters are
respectively used to set the start and end
time of the DLST.
For example, adjust the clock forward one
hour at 08: 00 on April 1st and backward one
hour at 08: 00 on October 1st. As shown in
Figure 2 on the right.
5. After setting the DLST, press [Done] to
return to the time setting interface. As
shown in Figure 3 on the right. Press [Save]
on the time setting interface to save current
settings and return to the previous interface;
press [Cancel] to directly return to previous
interface without saving current information.
70
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
14 System Information
You can check the storage status as well as version information of the FFR terminal
through the [System Information] option.
14.1 Records
The number of enrolled users, administrators and passwords is displayed on the
[Records] interface; the total fingerprint storage capacity and occupied capacity as
well as the total attendance storage capacity and occupied capacity are graphically
displayed respectively, as shown in the following figure:
71
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
14.2 Device
The Device name, serial number, version information, vendor and date of
manufacture are displayed on the Device interface.
14.3 Power Info
The Power Info interface displays the current Power supply and Battery Info. Show
as below:
.
72
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Appendix
Appendix 1 Text Input Instructions
The FFR terminal supports the input of Chinese and English characters, numbers
and symbols. Press related button to input text. For example, press [Name] to
display the text input interface, as shown in the following figure:
Keyboard Area
Text Display Area
Text List Area
Exit
Delete
Enter
Space
Chinese/English Switch Key
Character/Number Switch Key
Upper/Lower
73
Case
Switch
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
To enter a name, proceed as follows:
1. Press [Name] on the [Add] interface, as
show in figure 1 on the right.
2. Enter the characters of name, as shown
in Figure 2 on the right. Press [space] or
[Enter] to input the character.
3. After finishing the entry of name, press
[Enter] to confirm, as shown in figure 3 on
the right, and then press [X] to exit
keyboard interface and return to the
previous interface, as show in figure 4 on
the right.
74
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Appendix 2 Rules for Uploading Promotional Pictures
1.
All pictures must be in JPG format as other formats are not supported.
2.
The file name of a promotional picture must be ad_0 - ad_9. For example,
ad_1.jpg is a valid file name.
3.
After a picture is uploaded to the FFR terminal, its name does not change. To
replace this picture, you need to upload a new picture with the same file name to
overwrite it.
4.
The size of each picture cannot exceed 64K; otherwise, the upload will be
unsuccessful.
5.
The recommended resolution of the picture is 320 × 240. Pictures with
resolution higher or lower than 320 × 240 are not recommended.
6.
A maximum of 10 promotion pictures can be uploaded.
75
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Appendix 3 Introduction to Wiegand
Wiegand26 is an access control standard protocol established by the Access Control
Standard Subcommittee affiliated to the Security Industry Association (SIA). It is a
non-contact IC card reader interface and output protocol.
Wiegand26 defines the interface between the card reader and controller used in the
access control, security and other related industrial fields. Wiegand26 helps
standardize the work of the card reader designers and controller manufacturers. The
access control products manufactured by our company are also designed by
following this protocol.
Digital Signals
Figure 1 is a sequence diagram in which the card reader sends digital signals in bit
format to the access controller. In this sequence diagram, Wiegand follows the SIA’s
access control standard protocol for the 26-bit Wiegand card reader (one pulse time
ranges between 20us and 100us, and the pulse jump time ranges between 200us
and 20ms). Data1 and Data0 are high level (larger than Voh) signals till the card
reader prepares to send a data stream. The asynchronous low-level pulse (smaller
than Vol) generated by the card reader is sent to the access control panel (The
saw-tooth wave as shown in Figure 1) through Data1 or Data0. Data1 and Data0
pulses will neither overlap nor be generated synchronously. Table 1 lists the
maximum and minimum pulse width (a consecutive pulse) and pulse jump time (time
between pulses) allowed by the F series fingerprint access control terminal.
Table 1 Pulse Time
Symbol
Definition
Typical Value of Reader
Tpw
Pulse Width
100 µs
Tpi
Pulse Interval
1 ms
76
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Figure 1 Sequence Diagram
77
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Appendix 4 USB Host
Fingerprint device may be used as USB host to exchange data with external
U-disk.
The data transmission speed is quick, the traditional fingerprint device only
supports the RS232, RS485 or Ethernet way for data transmission, when as
a result of physical condition limit, data quantity big, and the data
transmission cost quite long time. But the USB data transmission is quicker
than any of the former transmission mode, may complete downloading data
by U disk in a short period of time, like this greatly enhances the efficiency.
The operational steps of USB Host equipment please refer to 7.USB Disk
Management.
Appendix 5 State Auto Switch
The system supports six work states: Check in, Check out, Break out, Break
in, Overtime in (OT-In), and Overtime out (OT-Out). The state needs to be
modified manually, that is, you can switch to the desired work state by
pressing the corresponding button. To decrease the manual operations, the
device menu provides a state Auto Switch option. At the time specified by a
user, the device automatically switches the state. The current state is
displayed on the initial interface.
78
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
After the user sets the state Auto Switch in a week, the system checks
whether the state needs to be switched by minutes. When the user saves the
settings, the saving operation of the same day or same time does not take
effect.
Appendix 6 Photo ID Function
Some FFR terminals also support the Photo ID function. The Photo ID
function is used to display the photo enrolled by a user or stored in a USB
disk on the screen in addition to such information as the user ID and name.
[Operation Steps]
1. When the photo taken by the FFR terminal is used, the photo can be
displayed upon successful verification.
2. To use a photo stored in a USB disk, proceed as follows:
A. Create a folder with the name of “photo” in the USB disk, and store users'
photos under this folder.
B. The user photos must be in JPG format and named after their IDs. For
example, for the user with user ID of 154, the photo name must be 154.jpg.
C. Insert the USB disk into USB slot on the FFR terminal, and select USB
Disk Management -> Upload -> Upload Photos. Then user photos can be
displayed upon successful verification.
Note: 1) The length of a user name cannot exceed 24 digits.
2) The recommended size of a user photo is less than 30K.
3) The uploaded new user photo will overwrite the existing photo in
79
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
related to the user ID.
D. To download user photos, select USB Disk Management -> Download ->
Download User Photos. A folder with the name of “photo” will be
automatically created on the USB disk, and all downloaded user photos are
stored under this folder.
80
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Appendix 7 Statement on Human Rights and Privacy
Dear Customers:
Thank you for choosing the hybrid biometric products designed and manufactured
by us. As a world-renowned provider of biometric technologies and services, we pay
much attention to the compliance with the laws related to human rights and privacy
in every country while constantly performing research and development.
We hereby make the following statements:
1.
All of our multibio recognition devices for civil use only collect the characteristic
points of multibio instead of the multibio images, and therefore no privacy issues
are involved.
2.
The characteristic points of multibio collected by our products cannot be used to
restore the original multibio images, and therefore no privacy issues are
involved.
3.
We, as the equipment provider, shall not be held legally accountable, directly or
indirectly, for any consequences arising due to the use of our products.
4.
For any dispute involving the human rights or privacy when using our products,
please contact your employer directly.
Our multibio products for police use or development tools support the collection of
the original multibio images. As for whether such a type of multibio collection
constitutes an infringement of your privacy, please contact the government or the
final equipment provider. We, as the original equipment manufacturer, shall not be
held legally accountable for any infringement arising thereof.
The law of the People’s Republic of China has the following regulations regarding
the personal freedom:
1.
Unlawful arrest, detention or search of citizens of the People's Republic of
China is prohibited; infringement of individual privacy is prohibited.
2.
The personal dignity of citizens of the People's Republic of China is inviolable.
3.
The home of citizens of the People's Republic of China is inviolable.
81
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
4.
The freedom and privacy of correspondence of citizens of the People's
Republic of China are protected by law.
At last we stress once again that biometrics, as an advanced recognition technology,
will be applied in a lot of sectors including e-commerce, banking, insurance and legal
affairs. Every year people around the globe suffer from great loss due to the
insecurity of passwords. The biometric products actually provide adequate
protection for your identity under a high security environment.
82
4.3 inches Facial & Fingerprint Recognition Series Product User Manual
Appendix 8 Environment-Friendly Use Description
The Environment Friendly Use Period (EFUP) marked on this product refers to the
safety period of time in which the product is used under the conditions specified in
the product instructions without leakage of noxious and harmful substances.
The EFUP of this product does not cover the consumable parts that need to be
replaced on a regular basis such as batteries and so on. The EFUP of batteries is
5 years.
Names and Concentration of Toxic and Hazardous Substances or Elements
Parts Name
Toxic and Hazardous Substances or Elements
Pb
Hg
Cd
Cr6+
PBB
PBDE
Chip resistor
×
○
○
○
○
○
Chip capacitor
×
○
○
○
○
○
Chip inductor
×
○
○
○
○
○
Chip diode
×
○
○
○
○
○
ESD components
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adapter
×
○
○
○
○
○
Screws
○
○
○
×
○
○
○: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials for this part is above the limit requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with non-hazardous
environment-friendly materials. The hazardous substances or elements contained cannot be
replaced with environment-friendly materials at present due to technical or economical
constraints.
83
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement