(Two Bid System): For supply of Equipments & Instruments

(Two Bid System): For supply of Equipments & Instruments
ESI-PGIMSR & ESIC MEDICAL COLLEGE
AND
ESIC HOSPITAL & OCCUPATIONAL DISEASE CENTRE (E.Z.),
(A statutory body under Ministry of Labour Govt, of India)
DIAMOND HARBOUR ROAD, JOKA, KOLKATA, 700 104
Fax: 033 2467 2795, Phone: 033 2467 1764 / 6280 / 1322/2799
(An ISO 9001:2008 CERTIFIED ORGANISATION)
Tender No. 412.U/16/30/3/Proposal/10-11 (Medical College)/Vol V
Dated: 17 . 09.2014.
Sub: Open Tender Enquiry – (Two Bid System): For supply of Equipments & Instruments
(NOTE: The envelope containing the tender as well as subsequent communications should be addressed
and delivered to ‘The Medical Superintendent’, ESIC Hospital & O.D.C. (E.Z), Diamond Harbour Road, P.O.:
Joka, Kolkata, 700 104, West Bengal. All communications must be addressed to the officer named above
by title only and not by name.)
To:
____________________________
_________________________
Sir(s),
Sealed tenders are invited (under Two Bid System - “TECHNICAL BID” & “PRICE BID”) by post/per
bearer from bonafide manufacturers / authorised dealers for supply of “Equipments & Instruments” as
per categories / specifications and/or quantities detailed in the Schedules / Specifications (Annexure – IV)
attached.
The “Tender Documents” comprising the Compulsory Documents (Annexure I) ,General Terms and
Conditions of Contract (Annexure II) and the Special Terms and Conditions of Contract (Annexure III) which
will govern any contract made, the Tender Application Form (Annexure IV) and the Schedule of contract /
specifications of items (Annexure-V) are enclosed herewith. If you are in a position to quote for the
contract in accordance with the requirements stated in the attached schedule as per the terms and
conditions stated, please submit your quotation to this office.
The tender document may be obtained from the office of the Medical Superintendent in person by
the bonafide applicant or his authorised representative by applying in their letter head at a cost of
Rs.1000.00 (Rupees One Thousand Only). The “tender documents” can also be downloaded from the
web site www.esi-pgimsrkolkata.org, the web site (www.esic.nic.in) and Central Public Procurement Portal
(eprocure.gov.in) and in such case the same may be signed and submitted as per the procedures
mentioned hereinafter along with the fee(s) for the “tender documents” @ Rs 1000.00 (Rupees One
Thousand Only) (To be submitted along with the Technical Bid. It should not be enclosed in the envelope
containing the Price Bid). All the payment may be made by Demand Draft; drawn in favour of ESI Fund A/c
No. 1, payable at Kolkata; Cheques will not be accepted.
Tenderers are requested that, before quoting their rates or sending tender, the tender forms may
please be read out thoroughly (line by line) so as to have a clear knowledge of the requirement
contained therein, otherwise purchaser will not be held responsible for any error / oversight of his own
and the penalties shall be levied for not complying with the requirements stated herein or supply of the
required item/services.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-1-
The form is a Standard Form of Tender. Certain clause / clauses may not be applicable in some
cases. So, Tenderers are requested to ignore such clause / clauses, which are not applicable in the instant
case.
The Tender forms containing the compulsory documents(Annexure – I ), the Terms and Conditions
(Annexure – II), the Special Terms and Conditions of Contract (Annexure III), the Tender Application Form
(Annexure IV) and the Schedule of contract / specifications of items (Annexure-V) should be returned in
original along with the technical bid document, intact, after filling up the same and duly signing in full
with stamp, on each page, failing which the tender shall be liable for rejection.
In the event of the space on the Schedule of contract / specifications of items/proforma being
insufficient for the required purpose, additional pages may be added. Each such additional page must be
numbered consecutively, bearing the Tender Number and be duly signed and stamped by the tenderer. In
such cases, reference to the additional pages must be made in the Tender Form. If any modification of the
schedule is considered necessary, you should communicate the same by means of separate letter sent
along with the Tender.
PARTICULARS
Cost of each Tender Document
Rs. 1000.00 (Rupees One Thousand Only)
Period for supply of Blank Tender Forms and
related documents at the Hospital on all
09.10.2014 to 02.11.2014 from 10.30 am to 3.00
Working Days (Except Saturdays, Sundays and
pm
Holidays)
Pre Bid Meeting
09.10.2014 at 2.00 pm
Due Date & Time of submission of completed
Tender Document in the Tender Box kept in the
03.11.2014 upto 2.00 pm
Office of ESIC Hospital.
Date & Time of Opening of Technical Bid
Bid Security / Earnest Money to be deposited
Performance security / Security Deposit Money
to be deposited
03.11.2014 at 2.30 pm
Amount of EMD to be deposited is, as mentioned
against each of the equipment / instrument /item
in annexure V of the tender document. While
quoting for more than one item, the earnest
money mentioned against each quoted item are to
be taken into consideration and added up while
submitting the earnest money / bid security.
10 % of the Bill Value of each of individual
equipment & instrument to be purchased from the
tenderer after selection.
Medical Superintendent, ESIC Hospital & ODC (E.Z), Joka, does not pledge himself to accept the
lowest or any tender and reserves the right of accepting or rejecting the whole or any part of the tender
without assigning any reason thereof. Canvassing in any form by the tenderer or his representative with
any of the officials of ESIC Hospital shall render the tender liable to be rejected.
Acceptance by the purchaser shall be communicated in due course. You are requested that the
instructions contained in the said communication should be acted upon immediately as asked for.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-2-
THE FIRM IS REQUESTED TO FOLLOW THE CHECK LIST AT THE TIME OF SUBMISSION OF TENDER
DOCUMENT WITHOUT WHICH THE OFFER IS LIABLE TO BE CANCELLED:
COMPULSORY DOCUMENTS:
[ Without which the offer is liable to be cancelled)
1. Tender Document Fee: Rs.___________ DD No.___________ dated__________
2. EMD Value: Rs.____________DD No.____________Dated______________
3. Valid Trade Licence Certificate: Valid upto________________
4. Warranty Certificate: At least for two years, submitted [Yes /No] [except item SL NO. 1 of
department of anaesthesiology where warranty is mentioned in the respective
specification]
5. VAT / CST certificate: Submitted [Yes /No]
6. Mandatory CMC for five years Certificate along with rates for different years:
Submitted, [Yes /No]
7. Mandatory spare parts availability for five years Certificate: Submitted, [Yes/No.]
8. Original tender document signing all the pages: Submitted, [Yes/No.]
9. Name & Address of Service Centre In KOLKATA: Submitted, [Yes/No.]
10. COPY OF PAN/TAN CARD: Submitted, [Yes/No.]
11. Certificate regarding provision of free calibration certificate for medical equipments for 07 years
[except item sl.no. 1 of department of anaesthesiology where free calibration certificate is required for
10 years.] [Yes/No.]
Enclosures:
1. Annexure – I (Compulsory Documents).
2. Annexure – II (General Tender Terms & Conditions).
3. Annexure – III (Special Tender Terms & Conditions).
4. Annexure – IV (Tender Application Form).
5. Annexure –V (Schedule / specifications of items/equipment).
Yours sincerely,
MEDICAL SUPERINTENDENT
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-3-
ANNEXURE-I
To
Tha Medical Superintendent
ESIC Hospital & Occupational Disease Centre (E.Z.),
Diamond Harbour Road, Joka, Kolkata, 700 104
COMPULSORY DOCUMENTS:
[ Without which the offer is liable to be cancelled)
1. Tender Document Fee: Rs.___________ DD No.___________ dated__________
2.EMD Value: Rs.____________DD No.____________Dated______________
3. Valid Trade Licence Certificate: Valid upto________________
4. Warranty Certificate: At least for two years, submitted [Yes /No] ] [except item SL NO. 1 of
department of anaesthesiology where warranty is mentioned in the respective
specification]
5. VAT /CST certificate: Submitted [Yes /No]
6. Mandatory CMC for five years Certificate along with rates for different years:
Submitted, [Yes /No]
7. Mandatory spare parts availability for five years Certificate: Submitted, [Yes/No.]
8. Original tender document signing all the pages: Submitted, [Yes/No.]
9. Name & Address of Service Centre In KOLKATA: Submitted, [Yes/No.]
10. COPY OF PAN/TAN CARD: Submitted, [Yes/No.]
11. Certificate regarding provision of free calibration certificate for medical equipments for 07 years
[except item sl.no. 1 of department of anaesthesiology where free calibration certificate is required for
10 years.] [Yes/No.]
Date:Place:-
Signature of the tenderer:Full Name:Designation:(Office seal of the tenderer)
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-4-
ANNEXURE-II
GENERAL TERMS AND CONDITIONS FOR TENDER / BID
1.
PREPARATION OF TENDER:
a. The original Tender form containing the Terms and Conditions (General and Special) and the
Schedule should be returned in original after filling up the form and duly signing in full on each page
with stamp, whether you are quoting for any item or not, failing which the tender is liable to be
rejected.
b. If any item in the schedule is not being tendered for, the corresponding space against the item
should be defaced by writing ‘not quoting’.
c. In the event of the space on the schedule form being insufficient for the required purpose,
additional pages may be added. Each such additional page must be numbered consecutively, bear
the Tender Number and be duly signed and stamped by you. In such cases, reference to the
additional pages must be made in the Tender Form.
d. The Tenderer shall, wherever call upon to do so, give full information with reference to the services
in hand and shall also permit the Medical Superintendent or any other officer nominated by him to
inspect the premises of the tenderer at all reasonable times and shall give full assistance and
information as may be required by him in connection with the contract.
2.
SIGNING OF TENDER:
a) The tender is liable to be rejected if complete information is not given therein or if the particulars
and date (if any) asked for in the tender are not duly & fully filled in. Particular attention may be
given to the dates of delivery, places of delivery and also to the particulars referred to in the
conditions of contract so as to comply with them.
b) Individuals signing tender or other documents connected with the contract must specify:
i)
Whether signing as a ‘Sole Proprietor’ of the firm or his Attorney?
ii)
Whether signing as a ‘Registered Active Partner’ of the firm or his Attorney?
iii)
Whether signing for the firm ‘Per Procreation’?
In the case of companies and firms registered under the Indian Partnership Act, the capacity in which
signing e.g. Secretary, Manager, and Partner etc. or their attorney and produce copy of documents,
empowering him to do so, if called upon to do so.
NOTE: In case of unregistered firms, all the members or all Attorneys duly authorised by all of them or the
Manager of the firm should sign the tender and subsequent documents.
1.
PROCEDURE FOR SUBMISSION OF TENDERS / BIDS:
1. The tender should be submitted in ‘TWO BID’ SYSTEM:i.
TECHNICAL BIDS:
a.
TECHNICAL BIDS in one separate envelope, sealed, super scribed
with the wordings “TECHNICAL BID”.
b.
The original copy of tender (Annexure – I to annexure - IV), duly
completed and signed on each page, should be submitted/returned back, enclosed along
with the “TECHNICAL BID”.
c.
The “Technical Bid” shall contain Earnest Money, the Cost of the
Tender Document (if downloaded from the web), both in the form of demand drafts as
prescribed hereinbefore, and all the technical details & documents along with
commercial terms and conditions in support of the quoted equipment.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-5-
d.
The Earnest Money Deposit (EMD) should be submitted in separate
envelope super scribed with the wordings “EMD” .
e.
Prices / Costs of the items should not be indicated anywhere in the
Technical Bid. This should be followed meticulously failing which the tender is liable to
be cancelled.
ii.
II.
III.
IV.
PRICE (FINANCE) BID
a.
PRICE (FINANCE) BID for each ITEM is to be submitted in SEPARATE
sealed envelopes, super scribed with the wordings “PRICE (FINANCIAL) BID” and the
“NAME OF THE ITEM”. All such sealed envelopes of Price Bids for individual items are to
be kept in a large sealed envelope, again superscribed with the wordings “PRICE
(FINANCIAL) BID”. This should be followed meticulously failing which the tender is liable
to be cancelled.
b.
The ‘Price/Financial Bid’ will contain item-wise price / cost for the
items mentioned / quoted in the technical bid.
Both the Technical Bid envelope and the Price (Financial) Bid envelope, prepared as above,
are to be kept in a larger single envelope super-scribed with “TENDER (TWO BID SYSTEM) FOR
SUPPLY OF Equipments and Instruments so as to give a double cover protection.
The outer cover should also be sealed and addressed to the Medical Superintendent in the
address mentioned hereinbefore.
Tenders submitted without following the ‘Two Bid’ System procedure will be rejected.
2.
LATEST HOUR FOR RECEIPT OF THE TENDER:
Your tender must reach this office not later than the date and time notified in the Tender Notice stated
in the TENDER DOCUMENT. Any tender received after that shall be rejected. In the event of the stipulated
date of opening of the tender being declared a closed holiday for Govt. offices, the date of opening of the
tender(s) will be the next working day. Tender sent by hand delivery, should be delivered at this office not
later than the due date and time stipulated in the schedule of tender.
3.
THIS TENDER DOCUMENT IS NON-TRANSFERABLE
4. PERIOD FOR WHICH THE OFFER WILL REMAIN OPEN AND PERIOD OF VALIDITY:
i)
All tenders should remain open for acceptance for a period of twelve months from the date of
opening of the tender.
ii)
The contract / tender, if awarded, shall be valid initially for one year from the date of award of
Contract subject to continuous satisfactory performance and on failure on this aspect by the
contractor, the Competent Authority will reserve the right to terminate the contract. The period of
the contract can be extended for further period at the discretion of the Competent Authority, to a
maximum of one year, on terms and conditions of the hospital, while accepting the tender.
iii)
Quotations qualified by such vague and indefinite expressions such as ‘subject to immediate
acceptance’; ‘subject to prior sale’ etc. will not be considered.
5. OPENING OF TENDER:
I. The Technical bids will be opened on the specified date and time in the presence of
bidders/representatives who choose to attend on the date and time as mentioned.
II. The bidders/ representatives who are present in the opening shall sign evidencing their attendance.
III. The Price/Financial bids of the bidders whose technical bids are found technically suitable (after
the selection of samples / demonstration of equipment / Item, if any) only will be opened later. The
decision of the committee on technical suitability shall be final and shall not be opened for
discussion.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-6-
6.PRICES:
i)
Prices are to be quoted in Indian Rupees.
ii)
Prices quoted in the Price/Financial Bid must be meaningful and measurable in the context.
iii)
The prices quoted must be per unit shown in the schedule inclusive of all packaging, installation
and delivery charges wherever applicable. Refunds on account of returnable package (if any) are to
be separately specified. Price & Fund must be clearly shown in figures and words.
iv)
Tenderers should clearly specify whether prices quoted are inclusive of Sales Tax/ VAT / duties /
statutory charges or such charges as extra. Where no specific mention is made to Sales tax / VAT/
or other duties, prices quoted shall be deemed to be inclusive of such taxes / charges.
v)
The ESIC Hospital and ODC (EZ), Joka, is not authorized to issue ‘C/D forms’.
7.
BID SECURITY / EARNEST MONEY:
The tenderer shall have to deposit an earnest money equivalent to the amount as mentioned against
each of the equipment / instrument /item in annexure V of the tender document with their Technical Bid
at the time of application, failing which the tender shall be rejected. While quoting for more than one
item, the earnest money mentioned against each quoted item are to be taken into consideration and
added up while submitting the earnest money / bid security and shall be paid in single demand draft . The
earnest money is to be paid by Demand Draft drawn in favour of ESI Fund A/c No. 1, payable at Kolkata.
NO CHEQUES OR CASH WILL BE ACCEPTED. In the event of the withdrawal / revocation of tenders before
the date specified for acceptance, the earnest money shall stands forfeited. In the event of acceptance of
the tender the earnest money may be adjusted, on written request, towards the amount of security
required to be deposited by the contractor in terms of Clause mentioned herein. The earnest money will
however, be returned without interest to the tenderer whose tender is not accepted after the finalisation
of the tender.
8.
SECURITY DEPOSIT / PERFORMANCE SECURITY:
On acceptance of the tender, within the period specified by the Medical Superintendent, the successful
tenderer / contractor shall deposit a sum equivalent to 10 % (Ten Percentages) of the Bill Value, rounded
off to the nearest Rupee, as security deposit, for due compliance & fulfilment of the terms and conditions
of the contract. This has to be in the form of a bank draft, drawn in any of the nationalised bank, in favour
of ESI Fund A/c No. 1, payable at Kolkata. NO CHEQUES WILL BE ACCEPTED for this purpose. On due
performance and successful completion of the contract in all respect including warranty period, the
security money deposit shall be returned to the contractor without any interest on presentation of an
absolute ‘No Demand Certificate’ in the prescribed form and upon return in good condition of any
specifications, samples or other property belonging to the purchaser, which may have been issued to the
contractor. If the contractor fails in fulfilling the terms and conditions mentioned here in different parts of
this tender document, such failure will constitute a breach of the contract and the Medical Superintendent
shall be entitled to make other arrangements at the risk and expense of the contractor. Also, nonperformance/unsatisfactory performance or violation of terms and conditions of the contract will make the
contractor liable for forfeiture of security deposit. The decision of the Medical Superintendent shall be final
and binding on this count.
9.
DELIVERY TERMS:
a.
Time and date of delivery: The essence of contract: - The time for and the
date of delivery of the stores / date of execution of work as stipulated in the schedule shall be
deemed to be the essence of contract and delivery / execution must be completed not later than
the date(s) specified. The delivery of the stores / execution of work / providing the services etc. are
required within a period as specified in the purchase order and as the place mentioned therein.
Normally maximum 6 weeks time is allowed from the date of issue of the purchase order for
execution of the supply of the equipment / article. However, the time allowed for execution of
order shall be governed by the stipulated time mentioned on the purchase order of Delivery of
equipment / Items.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-7-
b.
The tenderer shall deliver the stores/ execute the work at the destination /
space defined to the consignee / authority in good order (of which the Medical Superintendent,
ESIC Hospital & ODC (EZ), Joka, Kolkata shall be the sole judge) within the limits of the time as
deemed reasonable and specify in such quantities/qualities as may be ordered by him from time to
time.
c.
When a purchase order is placed to the successful tenderer, he shall have to
acknowledge the receipt of the said order within 10 (ten) days of the issue.
d.
In case this office does not receive supply of the above item(s), by due or
extended date of delivery, the above stated order will stand CANCELLED, unless extension is sought
for and granted by the competent authority for the late supply. In such cases, purchase of the
above items will be made at the tenderer’s RISK & COST without his consent and correspondence in
these regards. The competent authority reserves the right to recover the difference of excess
expenditure so incurred from the tenderer’s incoming bills or otherwise in addition to forfeiting the
earnest money deposited by the tenderer.
e.
But if the delay shall have arisen from any cause, such as strikes, lockouts, fire
accidents, riots, etc., which, the Medical Superintendent, ESIC Hospital & ODC (E.Z) may admit it as
reasonable ground for further time, and the Medical Superintendent may allow such additional
time required by circumstances of the case.
10.



11.
PAYMENT TERMS:
100% Payment will be made only after supply, inspection, complete installation and satisfactory
demonstration of performance of the item / equipment / instrument (including supply of all
accessories) subject to deposition of a sum equivalent to 10 % (Ten Percentages) of the Bill Value as
mentioned under Security Deposit / Performance Security Clause mentioned above or submission
of Performance Bank Guarantee for 10% value of the order valid for the warranty period from any
Scheduled Bank or. Otherwise 90% payment will be released after installation & balance 10%
payment will be released after warranty period or against bank guarantee for the warranty period.
No advance payment before effecting supply as above either part or full of any kind shall be made
under any circumstances.
Payment shall be made through cheque or Electronic Clearing System. Normally, payment is made
within six weeks after satisfactory inspection, installation and performance of the item / equipment
/ instrument subject to submission of appropriate and correct invoice, Challans and other
documents as deemed fit.
In case of cheque, the same may be dispatched through Registered Post.
OTHER TERMS:
a) Responsibility for executing Contract: The contractor is to be entirely responsible for the execution
of the contract in all respects in accordance with the terms and conditions as specified in the
acceptance of tender.
b) The contractor shall not sublet transfer or assign the contract to any part thereof without the
written permission of the Medical Superintendent. In the event of the contractor contravening this
condition, Medical Superintendent be entitled to place the contract elsewhere on the contractors
account at his risk and the contractor shall be liable for any loss or damage, which the Medical
Superintendent, ESIC Hospital & ODC (EZ), Joka, may sustain in consequence or arising out of such
replacing of the contract.
c) Recovery of sums due: Whenever any claim for the payment of a sum of money arises out of or
under this contract against the contractor the purchaser shall be entitled to recover of such sum by
appropriating, in part or whole the security/earnest money deposited by the contractor, when the
balance or the total sum to be recoverable, as the case may be shall be deducted from any sum
then due or which at any time thereafter may become due to recoverable under this or any other
contract with the purchaser. Should this sum not be sufficient to cover the full amount recoverable,
the contractor shall pay to the purchaser on demand the remaining balance due.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-8-
d) Insolvency and breach of contract: The Medical Superintendent may at any time by notice in writing
summarily terminate the contract without compensation to the contractor in any of the following
events, that is to say:i)
If the contractor being at individual or if firm, any partner in the contractor’s firm, shall
at any time be adjudged insolvent or shall have a receiving order or orders for administration of
his estate made against him or shall take any proceedings for liquidation or composition under
any insolvency not for the time being in force or shall make any convenience or assignment of his
efforts or enter into any arrangements or composition with his creditors or suspend payment of if
the firm be dissolved under partnership act, or
ii)
If the contractor being a company shall pass a resolution or the court shall make an
order for the liquidation of the affairs or a receiver of Manager on behalf of the debenture holder
shall be appointed or circumstances shall have arisen which entitled the court or debenture
holders to appoint a receiver or Manager.
iii)
If the contract commits any breach of this contract not herein specifically proved for:
Provided always that such determination shall not prejudice any right of action or remedy which
shall have accrued or shall accrue thereafter to the purchaser and provided also that the
contractor shall be liable to pay the purchaser for any extra expenditure, he is thereby put to but
shall not be entitled to any gain on repurchased.
e) Arbitration: In the event of any dispute or difference arising out of the terms and conditions lsid
down in this tender, the same shall be refered to Arbitrator appointed by the medical
superintendent. The procedure of the Arbitration will be governed by the provisions Arbitration Act
1996 (as amended as rules framed there under).
f) Document: The tenderer should have a valid Trade licence, PAN / TAN / other statutory document
as applicable and produce attested copies of such certificates along with the tender papers in
Technical Bid, failing which the tender is liable to be rejected.
g) Right to accept / reject: The hospital authority reserves the right to reject any or all tender without
assigning any reason whatsoever. Also, the hospital authority reserves the right to award any or
part or full contract to any successful agency at its discretion and this will be binding on the
tenderer.
h) The quantity shown in the tender can be increased or decreased to any extent depending upon the
actual requirement.
i) Assistance to contractor: The contractor shall not be entitled to assistance either, in the
procurement of raw materials required for the fulfilment of the contract or in the securing of
transport facilities.
j) In case of failure to comply with the provisions of the terms and conditions mentioned, by the
agency that has been awarded the contract, the hospital authority reserves the right to award the
contract to the next higher tenderer or outside agency and the difference of price will be recovered
from the defaulter agency who has been awarded the initial contract and this will be binding on the
tenderer.
k) Medical Superintendent, ESIC Hospital & ODC (E.Z), Joka, does not pledge himself to accept the
lowest or any tender and reserve to himself the right of accepting the whole or any part of the
tender or portion of the quantity offered and you shall supply the same / execute the work at the
rate quoted by you. You are at liberty to tender for the whole or any part.
l) Failure and Termination: If the contractor fails to delivery the stores or any instalments thereof
within the period prescribed for such delivery in the contract or any time liquidation the contract
before the expiry of such period, the Director (Medical)/Medical Superintendent may without
prejudice to his right to recover damages for breach of the contract, be entitled at his option.
i.
To recovery from the contractor as agreed liquidated damages, and not by way of penalty a
sum equivalent to 2% of the price of any stores which the contractor has failed to deliver within
the period fixed for delivery for the schedule for each month or part of the month during which
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
-9-
the delivery of such stores may be in arrears, where delivery thereof is accepted after expiry of
the aforesaid period, or
ii. To purchase elsewhere, without notice to the contractor, on his account and at the risk of
the contractor, the stores not delivered or stores of similar description (where stores exactly
complying with the particulars are not in the opinion of the Director (Medical)/Medical
Superintendent, ESIC Hospital & ODC (E.Z), Joka, readily procurable such opinion being final).
Without cancelling the delivery in respect of the consignments not yet due for delivery, or
iii. To cancel the contract or a portion thereof, and if so decided to purchase or authorise to
purchase of stores not so delivered or other of a similar description (where stores exactly
complying with the particulars are not, in the opinion of the Director (Medical) / Medical
Superintendent readily procurable, such opinion being final) at the risk and cost of the
contractor.
MEDICAL SUPERINTENDENT
ANNEXURE-III
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 10 -
SPECIAL TERMS AND CONDITIONS
The following special terms and conditions shall apply for supply of Equipments & Instruments”at
ESIC Hospital & O.D.C. (E.Z), Joka.
A.
INSPECTION / INSTALLATION OF ITEMS / EQUIPMENTS:
Supplies shall be accepted and work shall be certified as completed subject to satisfactory and complete
installation (upto full potentials claimed for that respective equipment/ Item) of the equipment / items
supplied including supply of all accessories, and certified by the assigned officer, and subsequent
inspection by Medical Superintendent, ESIC Hospital & ODC (EZ), Joka, or his assigned representative. Any
defect found in the materials / equipment / items supplied / work done will render the supplies / work
open to rejection and decision of the Medical Superintendent, ESIC Hospital & ODC (EZ), Joka, shall be final
and legally binding. The tenderers shall have to take the same (rejected store) back at their own cost and
risk, and shall replace such rejections with the items of standard specifications / quality as acceptable to
the Hospital Authority. Alternatively, the stores may be purchased from others / work may be executed
through others, at the risks and costs of the tenderer, at the discretion of the authority.
B. WARRANTY / GUARANTEE:
Along with the Technical Bid the following information are to be provided exclusively.
(i)
All the equipments shall be carrying at least 2 (two) years warranty / guarantee against
defects of manufacturer/workmanship and poor quality of components. Accordingly, the tenderers
shall indicate clearly and exhaustively the mandatory warranty / guarantee offered by them / by the
manufacturing / supplying firms, its duration, as well as the various Terms & Conditions involved
therein, at the time of submission of the Technical Bid papers.
(ii)
The tenderer must be able to provide CMC for the equipments quoted at least for a period of
five years. A declaration to such effect must be accompanied with the offer, in the technical bid.
(iii)
Uptime guarantee: During the warranty/guarantee / CMC period the firm will maintain the
equipment in good working condition. All the complaints will be attended by the firm within 24 hours
of the dispatch of a complaint to their office. The firm shall ensure that machine is set right within 10
days (Ten Days) of the intimation. However, the tenderer have to arrange similar equipment as a
standby at his cost and risk in case of breakdown. In case of the machine not being made functional
within 10 days (Ten Days), Stiff Penalty equivalent to 1½% of the cost of machine per week shall be
levied for every week of delay at the discretion of the authority. In addition, the tenderer have to
arrange similar equipment as a standby as stated above.
(iv)
A certificate about satisfactory performance of the equipment duly authenticated by other
existing users of the equipment has to be supplied.
C. SOFT WARE UPGRADATION:
Free up-gradation of software (all update & upgrades) at least for 5 years is to be provided wherever
applicable.
D. CERTIFICATES TO BE SUBMITTED ALONGWITH THE TECHNICAL BID:
The following written guarantee / declaration must be provided exclusively without which the quotation
shall be liable for rejection.
1.
The name, addresses, phone no, fax no, etc, of the authorised service centre in Kolkata for
each of the specific equipment / Article / item quoted.
2.
A certificate about satisfactory performance of the equipment duly authenticated by other
existing users of the equipment has to be supplied.
3.
A declaration that the CMC (including all spares & labours) shall be made available at least for
five years for each of the specific equipment / Article quoted.
4.
A declaration indicating willingness to provide CMC services at least for five years after the
expiry of the warranty for each of the specific equipment quoted. Accordingly, the tenderer must
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 11 -
quote prices for CMC, separately, for each year, for 5 years. The quotation for the cost of such
CMC are to be furnished along with cost of the equipment in the Price Bid. No such rate shall be
mentioned in Technical Bid.
5.
A declaration that the specific equipment/article with the given specifications has not been
sold / supplied to any other organisation at a lesser price than the price quoted here for each of the
specific equipment quoted here.
E. SAMPLES / DEMONSTRATION
The firms should be prepared to demonstrate their item(s) / arrange for demonstration of items
within 3 (Three) weeks from the date of opening of tender for verification / inspection, etc., or at a later
date as decided by the competent authority. The firm shall have to comply with such conditions failing
which the tenderer shall be liable for rejection and forfeiture of the Earnest Money. The tenderer / firm /
company shall arrange for demonstration of equipment / Item / article at his own cost and risk. Tenderer
who fails to demonstrate the equipments/ instruments quoted will not be considered for selection.
F. DETAILS OF ITEMS QUOTED:
It is mandatory to indicate the full name, make / brand, model number, and details specification of the
equipments quoted by them, (in addition, a brochure of product information may be attached along with).
Tenderers also have to indicate clearly the Name, Address and all Contact numbers of the
MANUFACTURING FIRM and the firm responsible for providing CMC, of the equipment quoted by them.
G. Within the warranty period, substitute working equipment of same model and make
must be temporarily provided by the supplier free of cost to cover for any downtime
exceeding 48 hours.
H. Onsite (in the hospital premises) Physical demonstration of the quoted model is
preferable. However in difficulties demonstration is allowed only within the Kolkata
city limit.
I. Cost of accessories & consumables should also be quoted separately in the price bid.
J. CMC is not applicable for Single small instruments.
K. Free calibration certificate for the Medical Equipments for 05 years.
L. BUY BACK OFER {wherever specified in the Schedules / Specifications (Annexure –V)}:
Preference will be given to the bidder who offers for buy back of the condemned equipments. The rate
for buy back offer of the condemned equipments is to be mentioned in the Price Bid. No such rate shall be
mentioned in technical bid. The equipments which are offered for buy back may be inspected by the
tenderers on any working day from 11 AM to 3PM.during the period of supply of blank tender form as
mentioned in the tender notice(at the time of issue of Tender Documents).
The payment will be made in shape of ECS/RTGS directly into the Bank Account of the Tenderer . Hence
the Tenderer is requested to submit the mandate form duly filled in and submit along with the bills.
MEDICAL SUPERINTENDENT
ANNEXURE - IV
TENDER APPLICATION/DECLARATION FORM
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 12 -
1
Name of the firm:a Full Postal Address:Cell Phone No.
b
2 c
d
e
Telephone No:Fax No.
E-mail address:
3
Date of Establishment of Firm:If your Firm Registered under:a The Indian Factories Act:4
Any other Act, if not, who are the owners
b
(Please give full address):Name and Address of your Bankers stating
5
the name in which the Account stands:Whether insured against fire, theft, burglary
6
etc. If so, please state the amount and name
of company with policy no:7
Total number of Employees:Are you in the list of approved contractors of
8
any other organisations / institutions, if any
give details (Append extra page if necessary):Give details of any Government contracts
9
executed during the last twelve months
(Append extra page if necessary):Any other information which you consider
10
necessary to furnish:
UNDERTAKING:
a.
I, the undersigned certify that I have gone through the terms and conditions
mentioned in the tender document and undertake to comply with them.
b.
The rates quoted by me are valid and binding upon me for the entire period of
contract and it is certified that the rates quoted are the lowest quoted for any other institution/
hospital in India.
c.
The earnest money of Rs.___________ to be deposited by me has been enclosed
herewith vide Demand Draft no.__________, Dt.___________, drawn on bank
____________________________, Branch __________________________________.
d.
I hereby undertake to supply the items as per directions given in the tender
document / supply order within stipulated period.
e.
I/We give the rights to Medical superintendent to forfeit the earnest money
deposited by me/us if any delay occur on my/agent’s part or failed to supply the article within the
appointed time or the items of desired quality.
f.
There is no vigilance/CBI case or court case pending against the firm.
Date:Signature of the tenderer:Place:Full Name:Designation:(Office seal of the tenderer)
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 13 -
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 14 -
(For Technical Bid Only)
PLEASE QUOTE YOUR RATE AS PER THE GIVEN SPECIFICATIONS.
The amount of Earnest Money / Bid Security to be deposited for each of the item quoted is mentioned against each serialised item below. The total amount
of Earnest Money for all the quoted items may be drawn in a single demand draft. However, in such case, the detail break up of earnest money submitted for
each item is to be furnished in a plain paper along with the bank draft.
ANNEXURE – V
SL. NO.
NAME OF
EQUIPMENT &
INSTRUMENT
REQUIRE
MENTS
(FOR ESIPGIMSR,
JOKA)
DEPARTMENT OF ANESTHESIOLOGY ESIC-PGIMSR & MC & ESICH & ODC (EZ) JOKA
Anesthesia
1.Three gas (O2, N2O, Air) Anesthesia Gas Delivery Unit with the the
1
03 pcs
Workstation
(with
multiparameter
patient monitor)
SPECFICATION
following sub specifications:
a) The unit should have primary connection for central medical gas supply
for O2, N2O and Air.
b) Provision for back up emergency supply through pin indexed O2 and N2O
small cylinders.
c) Electronically controlled gas mixing and delivery system.
d) In case of O2 failure, the machine should automatically switch over to Air.
e) Audio visual alarm for O2 failure.
f) Accurate control of minimum 25% O2 in fresh gas (through sensitive
oxygen ratio controller) up to flow of > 1 L/min, in presence of N2O. At
least 250 mL/min of O2 for low flow and minimal flow applications (fresh
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 15 -
EMD VALUE
90000.00
QUOTED
(YES/NO)
gas flow < 1 L/min).
g) Should be capable of accurate fresh gas delivery of up to 500 mL/min for
minimal flow applications.
h) Ergonomically located integrated emergency O2 flush with self returning
valve.
i) Should have single user-interface of at least 30 cm color display and
electronic fresh gas doing for adult, child and neonate modes. The same
user-interface should control and display all parameters including control
of ventilator modes, display of pipeline and cylinder pressures, FiO2,
ETCO2, airway pressures, tidal volume, minute ventilation, fresh gas flow,
etc.
j) The user-interface should have configurable screen layouts for individual
screen setups.
k) The machine should have fully automatic menu driven self test and user
check list. In case of emergency machine startup, it should be possible to
bypass the self test completely.
l) The system leak test should be done through the Y-piece of the circle
system and should not require user interaction during the test.
m) O2 safety flow adjustable from 0 – 12 L/min, through the vaporizer for
emergency back up use.
n) Machine should also have an independent fresh gas outlet for connection
to external circuit (Bain's circuit and Magill's circuit).
o) The machine should have a configurable nitrous-oxide-free operation (in
case of necessity).
p) Fresh gas flow setting 50 mL/min to 12 L/min.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 16 -
q) It should have the indicator to show the efficiency of fresh gas setting
while used in low flow and minimal flow.
r) In the event of complete loss of external electric power and internal battery
failure, it should be possible to manually ventilate the patient at 100% O2
and deliver anesthetic agent.
s) Major and critical components to be made of corrosion proof and durable
metal alloy.
2.Integrated Anaesthesia Ventilator:
a) Electronically controlled, electrically driven ventilator should not
require any driving gas or pneumatic power for its operation.
b) Ventilator should be suitable to ventilate adult, child and neonate
without changing ventilator bellows.
c) Ventilator should have fully automatic calculations and preset of
patient specific ventilation settings based on ideal body weight of
the patient.
d) Automatic breathing circuit compliance correction. Bellow should be
enough light weight as not to offer any constant PEEP.
e) Modes of ventilation: Spontaneous ventilation, Manual ventilation,
IPPV with plateau adjustment from 0 – 60 % of inspiratory time,
PLV (pressure limited ventilation) with decelerating flow, Pressure
controlled ventilation, SIMV-VCV, SIMV-PCV, Pressure Support
(PS), PS with CPAP, PS with SIMV (CMV/PCV).
f) Should be upgradeable to Volume assured mode - autoflow –
delivering set tidal volume at minimum airway pressure.
g) Peak inspiratory flow up to 150 LPM.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 17 -
h) Tidal volume adjustments from 20 mL to 1400 mL (upgradeable to
minimum 5 mL).
i) PEEP from 0 – 20 mbar, electronically adjustable.
j) Respiratory frequency 3 – 100 /min.
k) I:E ratio: 5:1 to I:99
l) Should have the capability to ventilate with atmospheric O2, in case
of O2 and power failure.
3.Circle breathing system, Circle absorber:
a) Compact circle breathing system suitable for standard, low flow and
minimal flow with minimum patient circuit volume including circle
absorber (approx. 3 L, excluding reservoir bag) for fast response to
change in fresh gas compensation.
b) Fresh gas decoupled / compensated breathing system for adult and
children.
c) Integrated warmer in circle absorber for breathing gas conditioning
and prevention of water condensation inside the circle system.
d) Breathing gas inlet and outlet of the circle system should be fitted
with reusable (autoclavable) bacterial-viral filter.
e) Should have facility of gas sampling from the breathing system.
f) Manual APL on circle system valve with direct setting of release
pressure.
g) Easy to fit and change circle absorber canister of about 1.5 L
capacity.
4. Vaporizers:
a) Temperature and pressure compensated and flow interdependent
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 18 -
vaporizer for Sevoflurane (1 such) and Isoflurane (1 such).
b) Vaporizer should have extended delivery range from 0 – 6%.
c) Vaporizers must have selective interlocking safety mechanism to
prevent simultaneous operation of two vaporizers.
d) Should have transport lock and provide hermetic sealing of agent
chamber during transport and storage.
e) The vaporizer should require no calibration in its life cycle.
5. Safety features and alarms:
a) The machine should have adjustable alarm limits for all the
parameters with auto set alarm function.
b) The machine should have automatic display of MAC/MACx values
and automatic activation of low agent alarm
c) Airway pressure low limit should automatically change with PEEP
setting changes.
d) Continuous monitoring and display of tidal volume, airway pressure,
ETCO2, FiO2 (paramagnetic O2 sensor), anesthetic agent
concentration (with automatic identification of anesthetic agent),
lung compliance (VCV modes).
e) Graphic display of curves and loops with fast analysis of change in
lung mechanics provided by simultaneous display of reference and
real time loops.
f) Bar graph display of tidal volume (inspiratory and expiratory
volume).
g) Trending for alarms and measured values with graphic trend
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 19 -
display.
h) The machine should calculate agent compensation and agent
uptake by patient on a case to case basis and display total fresh
gas consumption in the electronic logbook of the machine.
6. Accessories to be provided:
a) Should have at least 3 pc of RS232 connectivity port to communicate with
patient monitor or HIS for automatic data transfer.
b) Pin indexed yokes for O2 and N2O (one each)
c) The machine should have externally-fitted water and moisture
trapping chamber (large capacity) fitted to the medical air pipeline
inlet.
d) Trolley with drawer.
e) Floor mounting with durable caster wheels with brake.
f) Writing surface.
g) Color coded and DISS coded pipeline connections and hoses for O2, N2O
and Air.
h) Adult and Child breathing circuits (autoclavable).
i) Anesthetic face masks (silicone, latex free).
j) Water traps and sampling lines for gas analyzer.
k) Semi closed breathing system for adult and child (latex free).
l) Cylinder key (2 such) chained to the machine, near the cylinder yokes.
m) User manual.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 20 -
7.Quality standard of the equipment, warranty and after sales service:
a) All the components of the of workstation (anesthesia gas delivery unit,
vaporizer, ventilator, circle absorber and circle system), should be
manufactured by the same agency to maintain uniformity of parts and
efficient after sales service.
b) Authorization for standing by, terms of warranty & AMC & supply of
spares for 7 years.
c) Physical demonstration of the quoted model is mandatory.
d) Must have CE certification (EN 60601-2-13) w.r.t the essential
requirement for safety and performance of the anesthesia workstation.
e) The comprehensive warranty will be 5 years (including all spares and
labor) from the date of satisfactory installation of equipment. Also quote
rates for comprehensive CMC (including all spares and labor) for 6th to
10th year, after expiry of warranty period. Cost of spares, accessories and
consumables should also be quoted separately.
f) Within the warranty period, substitute working equipment of same model
and make must be temporarily provided by the supplier free of cost to
cover for any downtime exceeding consecutive 48 hours.
g) Facility for good after sale & service with trained engineers posted in
Kolkata.
Multi-parameter patient monitor (integrated with the anesthesia
workstation) with the following technical specifications are required.
1.Parameters:
a) Should be suitable for monitoring adult, child and neonatal patients
under anesthesia.
b) Should have minimum of ECG, SpO2, NIBP, 2 IBP, 2 Temperature
as inbuilt standard parameters. All other parameters should be by
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 21 -
upgrades as pods or modules and software.
c) ECG: Five lead ECG monitoring with simultaneous display of three
leads of ECG wave forms. Simultaneous display of twelve lead
ECG waveform should be possible.
d) Respiration: Through impedance pneumography from ECG.
e) SpO2: Should have digital display, plethysmography, and tone
modulation with change of
f) SpO2. Should be supplied with Masimo SET technology with
compatible sensors for Adult, Child and Neonate.
g) NIBP: Oscillometric method of NIBP measurement with stepwise
deflation. Adult, child, neonate preset modes. Compatible NIBP
cuffs for Large adult, Adult, Child and Neonate. Should display
systolic, diastolic, mean pressure in large, easy to read display.
Measurement modes: automatic, manual and stat. Automatic mode
adjustable intervals from 2 minute – 240 minutes and adjustable
alarms.
h) IBP: Simultaneous monitoring of 2 IBP. Range – 50 to 400 mmHg.
i) Temperature: Simultaneous monitoring of two temperature: core
and skin temperature.
j) Simultaneous monitoring of two IBP and one temperature should be
possible.
a)User Interface:
a) Should be suitable for adult, child and neonatal monitoring.
b) Should have non-volatile memory for graphic and tabular trending of
all monitored parameters as standard.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 22 -
c) Should have event recall for minimum of 50 events, graphical and
tabular trends, drug dose calculations, alarm logs, OxyCRG,
oxygenation-ventilation and hemodynamic calculations as standard.
d) Should have arrhythmia detection including life threatening
arrhythmias such as ventricular tachycardia, ventricular fibrillation,
asystole, as standard feature.
e) Should have manual and automatic setting of screen format.
f) Should have user selectable parameter priority and color selection
for parameter on screen.
g) Should have excellent cable management with as minimum as
possible cables at monitor and patient end for maximum user
friendliness.
h) Should have facility for both wired and wireless networking.
i) Should have minimum eight channels of waveforms with minimum 8
inch display.
j) Cursor tool for vertical and horizontal cursors.
k) Should have web browsing facility to review each networked
monitor through hospital LAN via PC in hospital LAN from remote
location should be possible as future upgrade.
b)Optional upgrades/ modules (to be quoted separately):
a) Neuromuscular monitoring module for monitoring neuromuscular
blockade.
b) Bispectral index module for monitoring depth of anesthesia.
c)Safety features:
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 23 -
a) Internal battery backup for minimum of 3 hours (Li-ion battery) to be
provided.
b) CE and US FDA certification for the monitor as well as the individual
parameter modules w.r.t the essential requirement for safety and
performance of the monitor and accessories.
c) Should have defibrillator and ESU protection, ECG Synchronization,
IABP interface (ECG and Arterial for triggering and deflation with a
device delay of < 20 milliseconds.
d)Accessories:
a) 5/12 lead ECG cable.
b) SpO2 Masimo set finger sensor with extension cable for adult, child
and neonate.
c) Temperature probes (2 pc).
d) NIBP Hose.
e) NIBP cuffs (large adult, adult, child, neonate).
f) IBP reusable cable for 2 IBP and 10 pc disposable transducers.
g) BIS module and DSC cable..
h) NMT module and cable with acceleromyograph..
i) User manual.
e)Warranty and after-sales service:
a) All the components of multi-parameter patient monitor should be
manufactured by the same agency to maintain uniformity of parts and
efficient after sales service.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 24 -
b) Authorization for standing by, terms of warranty & AMC & supply of
spares for 7 years.
c) Physical demonstration of the quoted model is mandatory.
d) The comprehensive warranty will be 5 years (including all spares and
labor) from the date of satisfactory installation of equipment. Also quote
rates for comprehensive CMC (including all spares and labor) for 6th to
10th year, after expiry of warranty period. Cost of spares, accessories and
consumables should also be quoted separately.
e) Within the warranty period, substitute working equipment of same model
and make must be temporarily provided by the supplier free of cost to
cover for any downtime exceeding consecutive 48 hours.
f) Facility for good after sale & service with trained engineers posted in
Kolkata.
2
Multi functional
Surgical OT
table ( C-arm
fluoroscope
compatible )
with electronic
control
Multi functional Surgical OT table ( C-arm fluoroscope compatible ) with electronic
control with the following specifications :
Should be a mobile universal operating table with Direct motor driven adjustment
of height, lateral tilt, Trendelenburg/anti-Trendelenburg.
It should be 100% oil free.
Should have a longitudinal adjustment of 250 mm.
Should have pneumatic spring support for leg section and back section.
Adjustment of the column functions should be electrically Motorised via cable
remote control
Should have additional operating panel with status indicators for tabletop
orientation on column.
Should have built-in electronic interface to allow remote diagnosis and software
updates via modem.
Should have maintenance-free battery, integrated in the column, which can be
charged via a separate charging cable that also serves for direct mains operations
if needed.
Basic tabletop should consists of seat section and back section that can be adapted
and extended to meet the requirements of all the surgical disciplines by
combining it with other tabletop components.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 25 -
03 pcs
100000.00
The system should have Electrical and functional safety with Microprocessor and
Sensor Technology Module.
Completely X-ray translucent tabletop.
Pads should be integrally foamed, electrically conductive, soft and detachable,
Velcro-free system for optimum hygiene and durability.
Should have stable running gear with 4 large double castors with a minimum
diameter of 150 mm for easy manoeuvring.
Should have foot switch for brake.
Should have H – shaped base providing a plenty of space for the surgical team's
feet.
Tabletop frame, column cladding, side rails and running gear frame should be
made from disinfectant-resistant, easy to clean stainless steel.
It should be operated manually without the remote.
Column drive
Height adjustment (without pads)
Trendelenburg/Anti-Trenelenburg
Tilt
Pneumatic spring-assisted leg section up/down
Standard leg section up/down°
Back section up/down
Longitudinal slide
Patient weight
Electro-mechanical motor
700 mm – 1.120 mm
30°/35º
+-25°
+20°/-90°
+-90°
+85°/-30°
250 mm
More than 225 Kg
The systems should be quoted with following General accessories :
1.
2.
3.
4.
5.
6.
7.
8.
9.
Arm positioning support with radiolucent upper arm pad and roll- 2 nos.
Shoulder support-1 pair.
Anaesthesia Screen-1 nos.
Suspended arm strap set-2 nos
Infusion pole with 4 hooks-1 nos.
Body strap with locking Clamps-2 nos.
Lateral support height adjustable-2 nos.
Clamps-4 no.
Semi-circular pad-1 nos.
The systems should be quoted with following Orthopaedic accessories :
1. Knee Arthroscopy adapter
2. Radial clamp
3. Leg holder
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 26 -
4. Side rail extension & adapter
5. The table should be USFDA, & CE and UL certified
6. It should be meeting international standards for medical and electrical safety
standards;
3
Portable Blood
Gas &
Electrolyte
Analyzer:
02 pcs
Technical Specifications of kit-based portable Blood Gas & Electrolyte
Analyzer:
1. The kit-based portable Blood Gas & Electrolyte Analyzer should be able
to measure the following parameters: pH, PCO2, PO2, Na+, K+, Ca++,
Glucose, Lactate and Hematocrit.
2. The analyzer must be small in dimension and portable system, easy to
transport by a single person to the patient's bed.
3. The analyzer must be easy to operate, intuitive user interface, requiring
minimum technical training of the operator.
4. The unit should operate on AC adapter or accompanying Li-ion battery
and should be able to operate while battery is being charged.
5. The sample requirement must not be more than 125 micro liters.
6. The single-use test cartridge should be self contained with all the reagents,
sensors & calibrating solutions required for the test.
7. The system should not use any other consumable other than test card (testkit) and thermal printer roll paper.
8. The system should be provided with a dedicated wireless (Bluetooth/IR)
thermal printer.
9. The
system
should
have
Amperometric,
Potentiometric,
Conductometric sensors for measurement of test parameters.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 27 -
and
20000.00
10. The system should have an embedded and detachable barcode reader.
11. The system should have Bluetooth / WiFi connectivity for data
communication with PC.
12. Should be USFDA certified and CE marked for all the main equipment as
well as the accessories and kits used.
4
Cardiac
Biomarker
Analyzer (Cardbased
Quantitative
Assay):
Technical Specifications of Cardiac Biomarker Analyzer (Card-based
Quantitative Assay):
a) The card-based portable Cardiac Biomarker Analyzer should be able to
quantitatively measure the following parameters: Troponin I, BNP, CKMB,
Myoglobin,
D-Dimer,
using
Fluorescence
Immunoassay
Technology.
b) The analyzer must be small in dimension and portable system.
c) The analyzer must be easy to operate, intuitive user interface, requiring
minimum technical training of the operator.
d) The unit should operate on AC adapter and also on inbuilt Li-ion battery
backup.
e) The sample requirement must be less than 300 micro liters for a given
panel of test.
f) The single-use test card should be self contained with all the reagents,
sensors & calibrating solutions required for the test.
g) The system should have inbuilt memory capacity of at least 500 test results
with date and time.
h) Operating temperature range between 18 and 30 degree Celsius.
i) The system should be provided with an in-built thermal printer.
j) The system should be able to interface with HIS and LIS software.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 28 -
02 pcs
20000.00
k) Should have built in QC check facility for the instrument.
l) Should be able to perform all the quantitative tests of a single sample in
less than 20 minutes.
m) Should be US FDA certified and CE marked for all the main equipment as
well as the accessories and kits used.
5
The
Endoscope
Drying Cabinet
The Endoscope Drying Cabinet should have the following technical
specifications:
1. Approximate dimensions: Width X Depth x Height = 1280 mm x 470
mm x 2150 mm.
2. Approximate depth of chamber = 370 mm; approximate volume of
chamber 0.6 cubic meters.
3. Number of endoscope positions: at least 6 (six).
4. Drying time = 120 minutes or less.
5. Storage time = 160 hours or more.
6. Power supply: 230V x 0.9 A, 50 Hz, AC.
7. Power consumption should be less than 150 watts.
8. Air supply: compressed air pressurized medical grade dry air, internal
pressure 3 – 8 bar, dew point = - 43 degree C.
9. Internal ventilator 30 cubic meter/h (approximately).
10. Hepa filter (filter class minimum 7) with 0.3micrometer/9997 DOP;
HEPA filter resistance = 200 Pa
11. Cabinet doors must be lockable, with user access control to prevent
unauthorized access.
02 pcs
5000.00
6
ELECTRO
SURGICAL UNIT
TECHNICAL SPECIFICATION FOR ELECTRO SURGICAL UNIT
03 pcs
5000.00
The Micro-processor based isolated Electro Surgical Unit should be compatible
with Argon Coagulator system, designed for all kind of General Surgeries with
both monopolarand bipolar modes.
The following features are required
1.
2.
3.
The unit should be entirely microprocessor based.
Machine should have LED displays.
“Highest power efficiency rating” - have to be within the range more than
97 %.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 29 -
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Real time tissue impedance monitoring technology to deliver the selected
power perfectly into a wide range of tissue types reducing thermal spread,
RF interference and Neuro muscular stimulation and spark using feedback
technology of sensing tissue types at a rate as high as 200 times in a second.
Return Electrode Contact Quality Monitoring (REM) system with Adaptive
REM facility.
The Machine should work with disposable dual plate patient's return
electrode with good quality of polyhesive adhesive get.
Patients' return electrode should be available in three sizes, for adults,
paediatric and neonatals.
The patient return electrode should be all disposable type.
The service provider of the unit should have their working office/workshop
in Kolkata.
Facilitating two surgeons at a time using one machine in the same surgery.
Numerical Error alarming system should be inbuilt.
With a single button on the machine, previous power setting can be recalled.
Should be type CF Equipment (IEC 601 – 1 & IEC 601-2-2) defibrillator proof.
Unit should be US FDA and CE certified
Facilitating under water procedures
Unit should have “Spray” mode with Highest Crest Factor (in the range of 79) - (*Crest Factor as an indicator of a waveform's ability to coagulate
bleeders without cutting effect.)
There should be option of changing the crest factor from low to high value
with a single button.
There should be sufficient Coag modes present for all applications (
Preferably 4 coag modes)
Must be compatible with smoke Evacuator system, Argon Plasma Coagulator
system and CUSA
Input power source;
Operating Range : 170-260 VAC
Line Frequency : 50-60 Hz
Minimum High Frequency Leakage
Bipolar Less than 60 mA
Monopolar Less than 150 mA
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 30 -
OUTPUT CHARACTERISTICS
Highest Powers should be in the below ranges
Precise – 70 Watts
Standard – 70 Watts
Macro – 70 Watts
Low – 300 Watts
Pure – 300 Watts
Blend – 200 Watts
Deisccate – 120
Flug. High Crest Factor – 120
Flug, Low Crest Factor-120
Spray - 120
OUTPUT WAVEFORMS :BIPOLAR: 470 Khz sinusoid
Monopolar Cutting
Pure: 393 kHz sinusoid
Blend: 393 kHz bursts of sinusoid recurring of 27 Khz
intervals. 50% duty cycle envelope
Monopolar Coagulation:
Dessication:Low 1: 240 +-40 Khz sinusoid recurring at 39 Khz. 8%
duty cycle
Low 2: 393 kHz sinusoid
Low 3: 393 kHz sinusoid
Fulguration:High 1: 470+-40KHz damped sinusoidal burstswith a
repetition frequency of 57 Khz
High 2: 470+-40KHz damped sinusoidal burstswith a
repetition frequency of 30 Khz
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 31 -
Spray:- 390 Khz damped sinusoidal bursts with a
randomised repetition centered at 28 kHz.
Frequency include 21 Khz ‹ f ‹ 35 KHz
Output Is further modulated by a random 250 Hz
envelope with a variable duty cycle
Output power changes by ‹ 15% or 5 Watts,
which ever is greater, as the line voltage varies
from 90 – 135 volts and 186 – 264 volts
(into a 300 ohm load)
7
FOWLERS’ SPECIFICATION OF FOWLERS’BED
1. Should have the full features of a hospital bed with adjustment
BED
of height, back, upper leg & lower leg sections & trendelenburg
on four separate crank systems.
2. Should have polymer molded handle.
3. Should have mild steel perforated sheet top.
4. Should have Back rest, upper leg section, trendelenburg/ Rev.
trendelenburg /Rev. trendelenburg & height adjustment on
cranck mechanism with polymer molded handle, polymer
molded head & foot boards . High grade synthetic body castors
125 mm diameter, 2 with break & 2 without breaks.
5. Should have raised back rest.
6. 125 mm high grade synthetic castors, 2 with break & 2 without
breaks.
7. Should have patient load bearing capacity safe working of 135
kgs.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 32 -
03 pcs
(against
condemnati
on)
10000.00
8. Should have collapsible type safety side rails (pair) with locks
on foot end.
9. Should have IV polish.
8
Forced air
warmer
Specifications for Forced air warmer
03 pcs
1. Forced air warmer for patient warming with adjustable automatic
temperature control between 32 - 44 degree Celsius, in steps of 4 degree
Celsius; with outlet hose temperature monitoring system. The warmer unit
should have the system of securely mounting on any IV pole or bed rail.
Non-tipping mounting pole, with caster wheels, and wire basket to be
provided with each warmer unit.
4000.00
DEPARTMENT. OF OBST. & GYNAE. ESI-PGIMSR, JOKA
1
Cardiotoc Specification of Cardiotocographic fetal monitor with Maternal Monitor.
ographic
Standard size colour TFT screen monitor for display of wave forms and digital
fetal
monitor
with
Automatic fetal movement detection facility in wave forms.
Maternal
Monitor
Support for external thermal printer or ink jet printer
Standard twin pregnancy monitoring system
Built- in rechargeable battery and AC/DC power supply.
Built-in network capability.
24 hours monitoring, data storage and reload capacity.
Fetal heart acceleration and deceleration measurement ability
Fetal heart base line beat to beat variation and acceleration, deceleration analysis capability.
Printing functions with paper for documentation.
Automatic monitoring mode and convenient operation by manual/digital keys and rotary
knob.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 33 -
03
pcs
15000.00
Light and auto-alarm ability complying with international standard.
OPTIONAL (Additional Specification):
Maternal monitoring parameters may be present in addition to fetal monitoring system.
ECG
SPO2
NIBP
Respiratory rate
Temperature
Other parameters
2
Endovi
sion
System
Technical Specification Endovision System
Specifications for Full High Definition Digital Camera
Qty-1
Camera Console and Camera Head with coupler
The system should have following features:
 It should have Pure digital signal with high definition video of 1920 x 1080p (min) native
resolution and progressive scan technology both on camera head and console
 It should be compatible with Aspect ratio of 4:3 and 16:9
 The system should have Digital Zoom to enhance the quality of Image size & cross
specialty standardization of the camera system, regardless of the telescope used.
 Digital zoom, white balance control and two peripheral controls on camera Head
 Integrated Gain/Shutter/Enhancement with automatic brightness control
 Video Outputs: two DVI, one SVHS, direct fiber optic output
 The system should automatically optimize all settings. The system should be ready- touse as soon as it is connected to the camera control unit.
 The system should be touch screen Menu driven, thus allowing the surgeon to
program the camera head functions as per the surgical needs & requirement.
 The system should have surgical multispecialty settings.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 34 -
01 pc
40000.00
Technical Specifications:
Image System:
1/3” Progressive Scan CCD
Pixels
Camera Head Weight
AGC:
Signal-to-noise ratio
Video output:
Power Supply
1920 X 1080 pixels per chip (min)
< 100 gms.
Microprocessor controlled
65-75 dB
S-video signal, Digital Video Interface
100-240 VAC, 50/60HZ
High Resolution Monitor (HD)
Qty-1
The system should have:
 Hi Definition Medical Grade Colored Monitor 26” IPS Alpha panel with LED backlight Flat
Panel Monitor
 PAL/NTSC system compatible. The response time should be <8ms.
 Composite, S-Video and DVI inputs.
 Compact & Lightweight design.
 The system should have Compact & Lightweight design
 The system should have Resolution of 1920 X 1080
 Aspect Ratio: 16:9 and contrast ration 1400:1with viewing angle 178 degree
 Must have a preset specality setting.
 Weight should not be more than 19lbs
LED Light Source (Mininmum of 240Watt)
Qty-1
The system should have:
Electrical specification
 Primary: 100 - 240 VAC, 50/60 Hz, 400 W
 Fuses (2): 5.0A 250V
Light Engine
 Type: Red, Green, Blue LEDs (Should have LED’s for light emission)
 Light outlets: 1
 Light intensity adjustment: continuously adjustable from 0 to 100% manually
 It should have Standby mode which will reduce light output to a minimum, preventing
the light cable from generating excessive heat
 It should have Electronic Scope Sensing Technology (ESST), a special safety feature
that helps prevent accidental burns caused by a light cable that is not connected to
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 35 -
the scope.
 Intuitive simple user Interface with LCD touch screen
 Universal Jaw Assembly to adapt any make of Fiber Optic Cable
Fiber Optic Cable
Qty-1
 Should be at least 4mm diameter and it should be compatible to transmit the best
picture quality from HD camera system.
 It should have the technology to ensures that the light source goes to standby mode
when it is detached from the scope
High Defination Laparoscopes:
10mm 30 degree
Qty-1
10mm 0 degree
Qty-1
5mm 30 degree
Qty-1
 Should be Fully Autoclavable
 Should be in both 0 and 30 degree
 Should be Wide Angled distortion free view
 Must be equipped with Universal Adaptor for other Light Sources
 Should have Yellow Sapphire Glass Tip Index for Optimum Evenness of Focus & Contrast
All the above equipment should be of single make
3
Lapar Specification for the Laparoscopic Hand Instrument
oscopi (Gynae)
c
Hand
Instru
ment
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 36 -
02
sets
20000.00
(Gyna
e)
Insufflators 45L








1
45 liter of high flow & having LCD Display measurement
Soft approach pressure control for safe recovery of abdominal pressure
Should have four mode & visual and audible alarms with min 0.1 L flow rate
Internal leakage detection capability
Integrated Gas heating
Having internal venting system for safety
Should have video on screen display
Unit should include heated tubing, hose & yoke
3
Trocar /Cannula Size 11 mm
Trocar with pyramidal tip ,multi function automatic valve, stopcock for insufflation
3
Trocar/Cannula Size 5.5 mm
Trocar with pyramidal tip ,multi function automatic valve, stopcock for insufflation
2
Reducer flap type 10/05 mm
Maryland Dissecting forceps, 5mm, working length 33 cm
5mm, Rotating, Dismantable with channel for cleaning & connector pin for unipolar
coagulation. Insulated Metal Handle without ratchet & Milled Radel shaft insulation. Easy to
change insert.
Kelly Beak Dissector forceps, 5mm working length 33 cm
5mm, Rotating, Dismantable with channel for cleaning & connector pin for unipolar
coagulation. Insulated Metal Handle with ratchet & Milled Radel shaft insulation. Easy to
change insert.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 37 -
1
1
Metzenbaum Scissor, 5mm, working length 33 cm
5mm, Rotating, Dismantable with channel for cleaning & connector pin for unipolar
coagulation. Insulated Metal Handle with ratchet & Milled Radel shaft insulation. Easy to
change insert.
Allis tooth Grasping forceps, 5mm working length 33 cm
5mm, Rotating, Dismantable with channel for cleaning & connector pin for unipolar
coagulation. Insulated Metal Handle with ratchet & Milled Radel shaft insulation. Easy to
change insert.
Alligator Grasping forceps,5mm, working length 33 cm
5mm, Rotating, Dismantable with channel for cleaning & connector pin for unipolar
coagulation. Insulated Metal Handle with ratchet & Milled Radel shaft insulation. Easy to
change insert.
5mm meso overian forceps, working length 33 cm
5mm, Rotating, Dismantable with channel for cleaning & connector pin for unipolar
coagulation. Insulated Metal Handle with ratchet & Milled Radel shaft insulation. Easy to
change insert.
5mm Oviduct Forceps, working length 33 cm
5mm, Rotating, Dismantable with channel for cleaning & connector pin for unipolar
coagulation. Insulated Metal Handle with ratchet & Milled Radel shaft insulation. Easy to
change insert.
1
1
1
1
1
1
Dissecting Electrode (L shaped) , 5mm, working length 33 cm
5mm instrument with proper insulation upto working tip
Dissecting Electrode (Spatula shaped) , 5mm, working length 33 cm
1
5mm instrument with proper insulation upto working tip
1
Suction / Irrigation cannulas. Trumpet valve.
5mm all metal & single hand control trumpet with perforations at distal tip for smooth function.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 38 -
05 mm Bipolar Fenestrated forcep with ring handle. Working Length 33cm should be with cable
1
1
Needle P C O D
Vaginal Rectractor (Uterine Manipulator) 10 MM with one cannula and attachment
5mm Straight tip needle holder with metal handle and ratcheting mechanism, can be desmantal
with channel for cleaning
1
1
1
5mm Knot pusher
1
5 mm Myoma Drill
Monopolar Cable
1
Standards & Safety for above equipments:
1. Should be FDA & CE approved product
2. Comprehensive training for lab staff and support services till familiarity
with the system.
3. Shall be certified to be meeting safety standard IEC 60601-1:2005
requirements
for the safety of endoscopic equipment.
4. The Manufacturer preferably should have their own authorized service
centre in Kolkata.
4
Hysteros
cope
Hysteros
copy set
Technical Specification- Hysteroscope
Hysteroscopy set
1. Examination sheath of suitable size with luer lock adapter.
2. Operating sheath with instrument channel for operating hysteroscopy of
suitable size.
3. Autoclavable telescope 30deg. diameter 4mm, length 30cm.
4. Polypectomy loop unipolar electrode suitable for polyductomy.
5. Bipolar Dissection Electrode, semi rigid suitable for hysteroscopy.
6. Monopolar High Frequency Cord with 4mm plug for HF unit, length 300cm
7. Bipolar High Frequency cord with 4mm plug for HF Unit, length 300 cm
8. Unipolar ball electrode suitable with above instruments.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 39 -
01 set
20000.00
9. Flexible scissors single / double action jaws suitable with above
instruments.
10. Flexible Biopsy and grasping forceps double action jaws.
11. Flexible Biopsy and grasping forceps double action jaws.
12. Biopsy spoon forceps double action jaws.
13. Flexible Scissor
14. Hysteroscopic cannulation system with guide and wire.
II Irrigation Systems
1.
2.
3.
4.
Should be fully automatic.
Should have irrigation capacity of 0 to 500 ml per minute
Pressure range should be 10 – 200 mmHg
Should have digital displays like preset pressure and preset flow
5. Should be supplied with the accessories like silicon tubing compatible with
the instruments suppied, power cord, etc.
6. Should work with input 200 to 240Vac 50 Hz supply
III. Digital endoscopic camera system
1.
2.
3.
4.
5.
6.
7.
8.
Should be a single chip camera technology.
Should have one composite video outputs and one S-video output.
Should have anti-moister filter for fiber scopes.
Should have fully automatic exposure control.
Should have automatic white balance with memory function.
Should have horizontal resolution of more than 450 lines.
Should be supplied with flat LCD TV of suitable size.
Should work with input 200 to 240Vac 50 Hz supply
IV Light source and fiber optic light cable
1. Should be a halogen light source with minimum 250W light output with 10
spare bulbs.
2. Should have manual light intensity control.
3. Should have inbuilt cooling system.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 40 -
4. Should have two lamps of 250W and should have provision to change over
in the event of failure from one lamp to another.
5. Should be supplied with flexible fiber optic light cable with minimum
diameter of 4.5 mm and minimum working length of 300cm.
6. Should work with input 200 to 240Vac 50 Hz supply
V Others
1. Should be supplied with suitable trolley.
2. Trolley should have at least 6 power sockets
5
6
Delivery
Bed
All equipments except irrigation system offered should have safety certificate
from a competent authority CE / FDA (US) / STQC CB certificate / STQC S
certificate or valid detailed electrical and functional safety test report from
ERTL. Copy of the certificate / test report shall be produced along with the
technical bid.
Specifications
Delivery Bed:
02
pcs
5000.00
02
pcs
30000.00
 Overall size: 1880L X 900w X600-800H mm.
 Tubular Frame work mounted on 125 mm dia castor two with breaks.
 Three Section top made of MS pipe with fixed cushioned mattress.
 Height Adjustment preferably Hydraulic height adjustment & back section adjustment
through electric actuator system.
 Trendlenburg/ Reverse Trendlenburg Positions through pneumatic pump.
 Leg end section can slide under the main section. Wheel lock system must be present.
 Provided with a pair of upholstery lithonomy position.
 SS telescopic IV Rod.
 Detachable SS Tray.
MICROSCO
PE
MICROSCOPE SPECIFICATIONS
Optical System:
UIS2 (Universal infinity-corrected) optical system
Illumination:
Built-in transmitted Koehler illuminator
6V/30W halogen bulb
100-120V/220-240V ~ 0.85/0.45A 50/60Hz
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 41 -
Focusing:
Stage height movement by roller guide (rack and pinion)
Stroke per rotation: 36.8mm
Full stroke range: 25mm
Upper limit stopper
Tension adjustment on coarse focus adjustment knob
Revolving Nosepiece:
Fixed quadruple nosepiece with inward tilt
Type:
U-CBI30-2, Binocular
U-CTR30-2,
Trinocular
Field
Number:
20
20
Tube
inclination
:
Interpupill
ary
distance
30°
adjustmen
t range:
48mm-75mm
Observation
Tube:
Stage:
Light path
selector:
30°
48mm-75mm
None
None (Bi 50%,
Video/Photo 50%
fixed)
Size:
188mm(W) x
134mm(D)
Movement range:
76mm X-direction x
50mm Y-direction
Specimen holder:
Double slide holder
Rubber grip:
Equipped as
standard
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 42 -
7
Portable
Ultrasoun
d Machine
Type:
Abbe condenser
NA:
1.25 with oil
immersion
Condenser:
Aperture in iris:
Built-in
Dimensions & Weight:
233mm(W) x 432mm(H) x
367.5mm(D), approximately 8.5kg
(approx. 18.7lbs.)
Specifications of Portable Ultrasound Machine
1. The unit should be compact, light weight, portable,sturdy and resistant to break & damage..
2. It should be suitable for vascular access (CVC placement,PICC) Nerve blocks(Lower as well as
upper extremity),E-FAST examination, AAA Exam, small parts, applications in adults and paed.
patients and also suitable for echocardiography & interventions. Multiple preloaded applications
presets should be available for the above.
3. The unit must have real time compound imaging for improved contrast resolution & eliminating
ultrasound artifacts to achieve optimum image quality.
4. The unit must have automatic gain adjustment for B mode imaging
5. Scanning depth must be available up to 35 cm.
6. System should support transducer technologies like convex, linear and phased array.
7. Imaging modes of real time 2D, color Doppler, Pulsed wave Doppler, Continuous wave Doppler
and Power Doppler must be available in all probes.
8. Simultaneous connectivity of at least 2 probes.
9. System must have fast start up to scanning in less than 60 seconds as essential in critical and
emergency situation in ICU, emergency & OT.
10. Cine memory on all modes
11. DICOM ready system with facility to print along with printer, store, ready to connect to PACS
12. Flat LCD/TFT monitor of at least 10” with flicker free image
13. Alphanumeric soft keys keyboard with easy access scans controls, facility to sanitize the system
keyboard
14. to avoid cross contamination must be available
15. Onboard storage of at least 10,000 images ,USB port for connectivity to computer
16. Should be able to operate both on AC and battery. Battery pack should be self recharging and
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 43 -
01 pc
10000.00
should last at least for 2 hours when fully charged.
17. Transducers to be provide as standard.
 High frequency Linear transducer 6-12 MHz with 60mm size for vascular access, small parts,
vascular, muscuskeltal
interscalene,Supraclavicular,Axillary,Musculocutaneus,Popliteal,Saphenous.
Higher frequency will be preferred.
 Convex transducer 2-5 MHz for deep nerve access specially Celiac,Sciatic
nerve,Epidural,Subgluteal & abdominal applications.
 Broad band phased array transducer,1-5 MHz for accessing the cardiac function & other related
application.
 Needle guide must be supplied for Linear & Convex probes along with 20 compatible needles with
the unit.
18. System should be supplied with trolley.
19. Valid US FDA/CE(European)/BIS certification.
8
Digital
Fetal
Doppler
01 pc
2000.00
01 pc
2000.00
Specifications for digital Fetal Doppler:
 Fetal doppler CE approved, with blue blacklight for dark sight
 Easy operation for everyone, over 10 years quality satisfaction
 Tm-100B Fetal Doppler CE Approved
 Ultrasound frequency : 2.5+-0.25Mhz
 Ultrasound output power : 10mW/cmDC
 Power supply:9.6V rechargeable battery
 Working environment temperature : 10-40
9
COLPOSCO
PE
TECHNICAL SPECIFICATIONS COLPOSCOPE
1. Should be a basic model with binocular tubes with inter papillary adjustment and
vertical stand.
2. Should have a working range with fine focus of minimum 40mm.
3. Should have a 12.5x or 13.5x or 15x eye piece.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 44 -
4. Should have a standard objective of working distance between 250 to 300mm.
5. The vertical stand should have at least 4 wheels and at least 2 of them should have
breaking facility.
6. The vertical joint should be rotatable and should have vertical height adjustment.
7. The head should be tiltable and should have positioning handle.
8. Should use a halogen light source with coaxial illumination.
DEPARTMENT. OF SURGERY ESI-PGIMSR, JOKA
1
OPERATING
HAND
INSTRUMENTS
OPERATING HAND INSTRUMENTS Set for LAPROSCOPIC SURGERY
01 set
1
Trocar /Cannula Size 11 mm
3
Trocar with pyramidal tip ,multi function automatic valve,
stopcock for insufflation
2
Trocar/Cannula Size 5.5mm
3
Trocar with pyramidal tip ,multi function automatic valve,
stopcock for insufflation
3
Maryland Dissecting forceps, 5mm, working length 33cm
1
Rotating, Dismantable with channel for cleaning & connector
pin for unipolar coagulation. Insulated Metal Handle without
ratchet & Milled Radel shaft insulation. Easy to change insert.
4
Curved Kelly Dissecting forceps, 5mm, working length 33cm
1
Rotating, Dismantable with channel for cleaning & connector
pin for unipolar coagulation. Insulated Metal Handle without
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 45 -
10000.00
ratchet & Milled Radel shaft insulation. Easy to change insert.
5
Right Angle Dissecting forceps, 5mm, working length 33cm
1
Rotating, Dismantable with channel for cleaning & connector
pin for unipolar coagulation. Insulated Metal Handle without
ratchet & Milled Radel shaft insulation. Easy to change insert.
6
Babcock Grasping forceps 5mm, working length 33cm
1
5mm, Rotating, Dismantable with channel for cleaning
Non insulated handle with ratcheting mechanism, easy to change insert
7
Alligator Light Grasping forceps,5mm, working length 33cm
1
5mm, Rotating, Dismantable with channel for cleaning & connector
pin for unipolar coagulation. Insulated Metal Handle with ratchet
& Milled Radel shaft insulation. Easy to change insert.
8
Fundus Grasper , 5mm, working length 33cm
2
5mm, Rotating, Dismantable with channel for cleaning
Metal Handle with ratchet & Milled Radel shaft insulation.
Easy to change insert.
9
Tooth Grasper / Allis, 5mm, working length 33cm, with double row of teeth
Rotating, Dismantable with channel for cleaning
Metal Handle with ratchet & Milled Radel shaft insulation.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 46 -
1
Easy to change insert.
10
Endo Grasper , 5mm, working length 33cm
1
5mm, Rotating, Dismantable with channel for cleaning
Metal Handle with ratchet and non-ratchet & Milled Radel shaft insulation.
Easy to change insert.
11
Double Action Claw , 5mm, working length 33cm
1
5mm, Rotating, Dismantable with channel for cleaning
Insulated Metal Handle with ratchet and non ratchet facility &
Milled Radel shaft insulation. Easy to change insert.
12
Metzenbaum Scissor, 5mm, working length 33cm
1
5mm, Rotating, Dismantable with channel for cleaning & connector
pin for unipolar coagulation. Insulated Metal Handle without ratchet
& Milled Radel shaft insulation. Easy to change insert.
13
Straight Metzenbaum Scissor, 5mm, working length 33cm
1
5mm, Rotating, Dismantable with channel for cleaning & connector
pin for unipolar coagulation. Insulated Metal Handle without ratchet
& Milled Radel shaft insulation. Easy to change insert.
14
Hook Scissor, 5mm, working length 33cm
1
5mm, Rotating, Dismantable with channel for cleaning & connector
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 47 -
pin for unipolar coagulation. Insulated Metal Handle without ratchet
& Milled Radel shaft insulation. Easy to change insert.
15
Dissecting Electrode (L shaped) , 5mm, working length 33cm
1
5mm instrument with proper insulation upto working tip
16
Dissecting Electrode (Spatula) , 5mm, working length 33cm
1
5mm instrument with proper insulation upto working tip
17
Clip Applicator 10 mm dia for Ethicon LT-300
1
10mm, Rotating, with channel for cleaning
Metal Handle without ratchet .
18
Suction / Irrigation cannulas. Trumpet valve.
1
5mm all metal & single hand control trumpet with perforations at
distal tip for smooth function.
19
Reducer 10 / 5 mm for reducing 10 mm to 5mm dia.
1
Aspiration Needle, 5mm
1
Gall Bladder Extractor
1
20
21
10mm, Rotating, Dismantable with channel for cleaning
Metal Handle without ratchet .
22
Monopolar Cable
1
5mm Bipolar Fenestrated Forceps with Ring Handle and cable
1
23
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 48 -
24
Reusuable bipolar cable
1
5mm Straight tip needle holder with metal handle and ratcheting
1
25
mechanism, can be dismantled, with channel for cleaning.
2
Ultrasonic
Scalpel with
Advance Vessel
Sealer system
01 set
Specification for Ultrasonic Scalpel with Advance Vessel Sealer system:
 System should have a universal connector to connect Ultrasonic energy and Advanced RF
energy instruments.
 System should have automatic instrument recognition.
 System should be CE approved.
 System should have a touch screen display for fast and setup, operation and on-screen
diagnostics.
 System should have a high-resolution display with wide viewing angles.
 System should have the ability for software updates via USB memory stick.
 System should be a single generator that provides Ultrasonic energy and Advanced RF
energy technology for soft tissue dissection and vessel sealing
 System should have a potential equalization terminal for compatibility with other
medical systems requiring such connections
 System should conform to the following international standards EN (IEC) 60601-1, EN
(IEC) 60601-1-2, EN (IEC) 60601-2-2, EN (IEC) 60601-1-8
 System should provide Class 1 protection against electric shock and defibrilation proof
 System should have a single footswitch for operating ultrasonic energy or advanced RF
energy instruments
 System should have the ability to select handswitch or footswitch activation or both for
Ultrasonic and advanced RF energy instruments and the ability to change selection
during use
 System should have multiple language options with English language as default
 System should not have minimal lateral thermal spread more than 1 mm.
 System should not have an auto switch off mechanism.
 System should have standby mode to ensure safety.
 System should come equipped with system diagnostics and troubleshooting guide to pin
point any problems in the systems.
 System should have onscreen warning display system for generator overheating,
generator software upgrade, hand-piece errors and instrument errors
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 49 -
10000.00

System should be able to power ultrasonic energy instruments 50 KHz frequency and
have the ability to power ultrasonic energy instruments in the frequency range of 3080 KHz in future
 System should be compatible for open surgery and for laparoscopic surgery.
 System should be compatible with both 5mm and 10mm instruments.
 System should have atleast 5 power settings levels along with display
 System should be able to power energy instruments with microprocessor controlled
bipolar electrosurgical radiofrequency technology with a quasi-sinusoidal forced
impedance output.
 System should be equipped with smart advanced RF energy technology to measure
the tissue impedance and control the power delivery.
 System should be equipped with advanced RF energy technology that can
simultaneously seal and transect vessels up to and including 7mm, large tissue
pedicles and vascular bundles.
 System should be equipped with advanced RF energy technology that provides
temperature controlled energy delivery which should maintain tissue temperature
approximately at 100 degree Celsius.
 System should have Advanced RF Energy hand instruments with a unique electrode
configuration to minimize the lateral thermal spread.
 System should have Advanced RF Energy hand instruments with technology to deliver
high compression uniformly across seal area.
 System should have Advanced RF Energy hand instruments that provide tissue / vessel
seal strength to withstand bursting pressure of more than 5 times the systolic
pressure.
 All hand probes for open and lap procedures should be able to simultaneously cut and
coagulate tissues.
 System should be able to power advanced RF energy hand instruments of 5mm shaft
diameter for both open & laparoscopic procedures in the following shaft lengths
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 50 -
(14cm, 25cm, 35cm & 45cm) and should be both hand & foot activated.
 Systems should be able to power ultrasonic energy hand instruments of 5mm shaft
diameter for both open & laparoscopic procedures and should be both hand and foot
activated.
Hardware:
1 Generator : 1 Set
2 Footswitch & Cable – 1 No
Accessories:
1 Hand Piece (Transducer)-1 No
2 Adaptors for ultrasonic and advanced RF energy instruments -1 Set
Probes of Ultrasonic scalpel:
1. Lap Probe (36cm)- 12nos
2. Open Probe (23cm)-- 6 nos.
Probes of Advance Bipolar:
1. Lap Probe(35cm)- - 6nos
2. OpenProbe(14 cm)--- 6nos.
DEPT OF DERMATOLOGY ESI PGIMSR, JOKA KOLKATA
1
Radiofrequen
cy machine
02
pcs
Radiofrequency machine
Number of items: 2
Power required: 230v/50 hz
Dimensions 260x300x150
Weight 7kg
Electrodes insulated
Frequency 0.20-2.93 Mhz
Cut: 70%cut, 30% coagulation
Coagulation : 60%coagulation, 40% cut
Fulguration: available
intensity control: Linear
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 51 -
2000.00
2
Centrifuge
machine
Centrifuge machine
Number of items- 2
Capacity in ml: 24x5
Type of head: Angle
No. of tubes: 24
Maximum speed: 3500 rpm
Maximum RCF: 1250
W×D×M (MM) : 210×210×250
Supply: 221-240v, 50Hz, single phase
02
pcs
500.00
3
Binocular
microscope
Binocular microscope
Optical system: UIS2 (UNIVERSAL INFINITY CORRECTED)
CE certified
Antifungal treated optical lens
Illumination: built in transmitted Koeheler illuminator, 6v/30W halogen bulb
100-120V/220-240V ̴ 0.85/0.45A , 50/60 Hz
Focussing: Stage height movement by roller guide (rock & pinion), stroke/rotation=36.8mm
Full stroke range: 25mm
Revolving nose piece: Fixed, quadruple nose piece with inward tilt
Binocular observation: field no. 20, tube inclination:30 degree, interpupillary distance adjustment
range: 48mm-75mm
Stage: size-188mm x 134mm, movement range: 76mm (X direction) x 50mm (Ydirection)
Specimen holder: double size holder
Rubber grip: equipped as standard
Condenser: type- Abbe condenser, NA: 1.25 with oil immersion, aperture in diaphragm: built in
Dimensions & weight: 233mm (W) X 411mm (H) X 367.5 mm (D), 8KG
02
pcs
6000.00
01 set
50000.00
DEPT OF ENT ESI PGIMSR, JOKA KOLKATA
1
Surgical
Operating
Microscope
Specification of Surgical Operating Microscope
Surgical operating microscope for micro ear surgery and micro laryngeal surgery with the
following associated features;
1. Integrated HD monitor to display surgical steps to students.
2. Integrated HD video recording system with HD camera system.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 52 -
3. Integrated HD still photography enabling system with camera attachment facility.
4. Data storage, transmission and documentation facility with appropriate software.
5. Stereo co-observation tube for assistant surgeons and students.
6. Lens for ear and laryngeal surgery (400, 200)
7. Lens covers and microscope covers for sterility purposes
8. Microscope stand and wheels.
2
Specification for Rigid Oesophagoscope set Adult:
Rigid
Oesophagosco 1. 0 degree telescope diameter 5.5mm, length 53 cm, autoclavable with incorporated fibre optic
light transmission
pe set Adult
2. Telescope guide for use with 50cm esophagoscope
3. fibre optic light carrier for use with 50cm esophagoscope
4.Rigid oval esophagoscope, outer diameter 12 X 16 mm, length 50 cm
5. Rigid oval esophagoscope, outer diameter 10X14 mm, length, 50 cm
6. Prismatic light deflector, autoclavable with fibre optic light cable connection
7. fibre optic light carrier for use with 30cm esophagoscope
8. Rigid oval esophagoscope, outer diameter 12.2X 16.2 mm, length 30 cm
9. Rigid oval esophagoscope, outer diameter 10.2 X14.2 mm, length 30 cm
10. Rigid oval esophagoscope, outer diameter 8.6X 12.1 mm, length 30 cm
11. Fibre optic light carrier for use with 20 cm hypopharyngoscope
12. Rigid Oval Hypopharyngoscope, outer diameter 10X14 mm. length 20 cm
13. handle for Esophagoscopes
14. Adjustable magnifier autoclavable(swivel action)
15. Cotton carrier(55cm)
16. Rigid suction tube with rubber tip, straight, working length 55cm
17.spring handle sponge holder, working length 55cm
18. Alligator forceps for hard foreign bodies, double action jaws, sheath diameter
2.5mm,working length 55cm
19. biopsy forceps and foreign bodies, working length 55cm
20. cupped forceps for biopsies, working length 55cm
21. Peanut removal forceps ,working length 55cm
22. Cotton applicator, working length 30cm
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 53 -
01 set
10000.00
23. Straight suction tube with rubber tip, working length 35cm
24. Spring handle sponge holder, working length 35cm
25. Alligator forceps, sheath diameter 2mm,working length 35cm
26. Peanut forceps, working length 35cm
27. Cupped forceps for biopsy ,working length 35cm
28. Universal forceps for biopsy and foreign bodies ,working length 35cm
3
Rigid
oesophagoscop
y set ,
Paediatric
Specification for rigid oesophagoscopy set , Paediatric
1, Oesophagoscope tube, size 6,length 30 cm
2. Oesophagoscope tube, size 5, length 30 cm
3. Oesophagoscope tube, size 4, length 30 cm
4. Oesophagoscope tube, size 3.5, length 18.5 cm
5. Oesophagoscope tube, size 3, length 18.5 cm
6. Prismatic light deflector ,autoclavable with connection for fibreoptic light cable
7. Rubber telescope guide
8. Adjustable magnifier (swivel action) autoclavable
9. 0 degree telescope, diameter 2.9 mm, autoclavable, fibreoptic light transmission incorporated
10. Optical forceps,2x2 tip, with spring action handle for use with telescope (for coins and flat
foreign body) to be used with 30 cm oesphagoscope
11. Optical forceps with spring action handle for use with telescope (for peanuts and soft foreign
body) to be used with 30 cm oesphagoscope
12. Optical forceps with spring action handle for hard foreign bodies to be used with 30 cm
oesphagoscope
13. Peanut removal forceps with double action jaws, sheath diameter 1.5mm,working length
35cm
14. Biopsy and foreign body forceps, double action jaws, sheath diameter 1,5mm, working
length 35cm
15. Alligator forceps for hard foreign bodies, double action jaws, sheath diameter 1.5mm,
working length 35cm
16. Cupped forceps for biopsy, double action jaws, sheath diameter 1.5mm, working length
35cm
17. Straight suction tube with rubber tip, working length 35cm
18. Straight cotton applicator working length 35cm - 3 such
01 set
10000.00
4
Rigid
bronchoscopy
set, adult
Rigid bronchoscopy set, adult
1. 30 degree telescope, diameter 5.5mm, length 50cm, autoclavable, fibreoptic light transmission
incorporated
01 set
10000.00
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 54 -
2. 90 degree telescope diameter 5.5mm, length 50cm, autoclavable, fibreoptic light transmission
incorporated
3. Rigid bronchoscope, size 8.5, length 43cm
4. Rigid bronchoscope, size 7.5, length 43cm
5. Rigid bronchoscope, size 6.5, length 43cm
6. Deflecting device for bronchoscopes and telescopes
7. FLUVOG Adapter with sliding glass window plug, sealing cap, notched lense and keyhole
opening, movable
8. Adapters to respirator - 2 such
9. Rubber telescope guides - 2 such
10. Glass window plug - 2 such
11. Instrument guides for suction catheter - 2 such
12. Injection canula for positive pressure assisted ventilation, LUER lock, outer diameter 3.5 mm
for use with bronchoscopes
13. Optical forceps, alligator, large jaws for hard foreign bodies
14. Optical biopsy forceps, circular cup, 4.3mm
15. Flexible forceps for biopsy
16. Alligator forceps for hard foreign bodies, double action jaws, diameter 2.5mm, working
length 50cm
17. Peanut removal forceps, double action jaws, sheath diameter 2.5mm, working length 50 cm
18. Cupped forceps for biopsy, double action jaws ,sheath diameter 2.5mm, working length 50
cm
19. Cotton carrier, working length 50cm - 6 such
20. Sponge holder with spring handle, working length 50cm
21. Cytology brush with ring handle, working length 55cm
22. Coagulation suction tube, insulated, working length 50 cm accompanied by unipolar high
frequency cord with 5mm plug, length 300cm
23. Straight suction tube with rubber tip, working length 50cm - 2 such
24. Curved suction tube with rubber tip, working length 50 cm
25. Suction tubes 4mm diameter, length 50 cm - 2 such
26. Aspirator, can be connected to suction tubes or suction catheter
27. Spare glass for aspirator
28. HUZLY Aspirator and bronchial irrigator
29. Laryngeal syringe, 5ccm, LUER lock, with canula
30. Bronchial atomizer, with graduated container and rubber bulb, length 50cm
31. Laryngeal atomizer with bulb, length 50 cm
32. Suction catheter, 7 Fr with connector
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 55 -
33. Suction catheter, 5 Fr with connector
5
Rigid
Rigid bronchoscopy set, Paediatric
bronchoscopy 1. Bronchoscope size 6, length 30cm
set, Paediatric 2. Bronchoscope size 4.5, length 30cm
3. Bronchoscope size 3.7, length 30cm
4. Bronchoscope size 3.5, length 26cm
5. Bronchoscope size 3, length 26cm
6. . FLUVOG Adapter with sliding glass window plug, sealing cap, notched lense and keyhole
opening, movable
7. Adapters to respirator - 2 such
8. Rubber telescope guides - 2 such
9. Glass window plug - 2 such
10. Instrument guides for suction catheter, short, for children and infants - 2 such
11. Injection canula , only, LUER lock, outer diameter 3.5 mm for use with bronchoscopes - 2
such
12. Prismatic light deflector, autoclavable with connection for fibreoptic light cable
13. Cotton applicator, working length 35cm - 3 such
14. Sponge holder with spring handle, working length 35cm
15. Foreign body basket with ring handle, working length 35cm
16. Cytology brush with ring handle, working length 35cm
17. Straight suction tube with rubber tip, working length 35cm
18. Curved suction tube with rubber tip, working length 35cm
19. Suction tube, 3mm, working length 35cm, curved
20. Bronchial atomizer, graduated container and rubber bulb, working length 40 cm
21. Graduated containers - 2 such
22. Aspirator with spare glass and cut off hole, can be connected to suction tube or catheter
01 set
10000.00
6
AUDIOMETER
01 set
10000.00
AUDIOMETER REQUIREMENT
The audiometer should have the following specifications:
*It should be a Clinical PC-based audiometer.
*The manufacturer should provide instructions and provision for calibrating the instrument.
*The following tests should be able to be performed by the audiometer:

Pure tone audiometry, Speech audiometry ( Including Speech reception threshold and
speech discrimination score), SISI, ABLB, AUTO THRESHOLD , TONE DECAY
*It should have the following provisions:
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 56 -
7
IMPEDENC
E
AUDIOMET
ER

SMPS
Switch Mode Power Supply capable of withstanding extreme
voltage fluctuations (115 V to 270 V)

INPUT: Tone, Speech, Tape, Pulse Tone.

OUTPUT: Left, Right, Bone, L + R. F/F Left, F/F Right, F/F L+R.

HEADPHONES: TDH-39/TDH-49.

BONE: B-71 BONE CONDUCTOR.

Air : 120 dB Max, 125 Hz to 12 kHz., -20 dB Min.

Bone : 80 dB Max, 250 Hz to 6 kHz., -20dB Min.

Noise : Wide Band, Narrow Band, Speech Band.

Built-in Mike, Ext. Mike, Mike Sensitivity Control.

Interrupt Lock.

Printer Facility-Sequential Merged Graphs.

Memory Review.

Computer Interface.

Storage of the patient data in the hard disc for future reference.

Connectivity to an external USB Printer to print the reports.
IMPEDENCE AUDIOMETER
 It should meet the international standards
 Should be able to test the following
1. Tympanometry
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 57 -
01 set
10000.00
2. Acoustic reflex test
 Should have facility for producing printed report
 Should have facility for data storage
8
FLEXIBLE
NASOPHAR
YNGOSCOP
E
FLEXIBLE NASOPHARYNGOSCOPE
01set
15000.00
01 set
2000.00
 Should be able to view nasopharynx, larynx, trachea and hypopharynx
 Should be able to take biopsy with flexible forceps
 Should have suction and irrigation facility
 Should have own cold light source
9
TYMPANOMAS
TOID SET
SURGICAL INSTRUMENTS
TYMPANOMASTOID SET
1. SHEA aural speculum – set of 4, black finish – 3 sets
2. Tumarkin tapered slotted aural speculum – set of 4 – 3 set
3. Adsonforcep – plain – S.Steel – 6 such
4. Adsonforcep – 1x2 teeth – S.Steel – 6such
5. Hartmann aural forcep – 3 such
6. Lempert endaural speculum – right – 3 such
7. Mollison self retaining mastoid retractor 3 such
8. Plester self retaining retractor 2x2 prong – 3 such
9. Plester self retaining retractor 3x3 prong – 3such
10. Plester self retaining retractor – right solid blade – 3 such
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 58 -
11. Plester self retaining retractor – left solid blade – 3such
12. Farabeuf periosteum elevator – straight – 3 such
13. Freer’selevator double ended – 3 such
14. Howarth elevator – 3such
15. Zollner suction tube with 4 microtips – 3 such
16. Verhoeven suction tubes – no. 12,14,16,18,20,22,24 – 3 sets
17. Verhoeven suction tube adaptor – 3 such
18. Micro aural crocodile serrated – fine straight – 3 such
19. Micro aural cup – straight – 3 such
20. Micro aural cup – upward – 3 such
21. Micro aural scissors – straight – 3 such
22. House dieter malleus nipper – up – 3such
23. House dieter malleus nipper – down – 3 such
24. Caw Thorne hook – micro pick 90 degree angled – 3 such
25. Caw Thorne hook – micro pick 45 degree angled – 3 such
26. Wullstein needle – very slight curved – 3 such
27. Wullstein needle – slight curved – 3 such
28. Wullstein needle – straight – 3such
29. Rosen curette curved straight shaft – 3uch
30. Sickle knife – 3 such
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 59 -
31. BealesRaspatory – 3 such
32. Circular cutting knife 60 degree – 3 such
33. Ball probe – 3such
34. Rosen elevator for lifting drum – 3such
35. Plester first incision knife – 3 such
36. Curved circular cutting knife – 3 such
37. House curette double ended – 3 such
38. House curette double ended slightly curved – 3 such
39. Myringotomy knife – 3such
40. Small curved scissor – 3 such
41. Mastoid micromotor drill (30000 rpm) 1
42. Straight hand piece for mastoid drill 1
43. Contra angle hand piece for mastoid drill 1
44. SS cutting burrs ( 8mm,6mm,4mm,2mm,1mm0.8mm) 1 each
45. Diamond polishing burrs (6mm, 4mm, 2mm 1mm) 1 each
10
01 set
STAPEDECT
OMY SET
STAPEDECTOMY SET
Each instrument one number required
 Round Knife 45° diameter 1 mm, length 16 cm
 Flag knife
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 60 -
50000.00
 Micro elevator
 Sickle Knife, double-edged, standard model, slightly curved, length 16 cm
 Pick 90°, 16 cm, 0.6 mm
 Pick 90°, 16 cm, 0.8 mm
 Ear Forceps extra delicate, serrated, 0.4 x 3.5 mm, working length 8 cm
 Ear Forceps extra delicate, pointed, serrated, 1 x 4.5 mm, working length 8 cm
 Scissors delicate standard model, blade length 8 mm, working length 8 cm
 Malleus Nipper, extra delicate, upbiting, width 0.8 mm, working length 8 cm
 Ear Forceps extra delicate, oval cupped jaws, 0.6 mm, working length 8 cm
 Ear Forceps extra delicate, oval cupped jaws, 0.9 mm, working length 8 cm
 Perforator, 16 cm,diameter: 0.4 mm.
 Perforator, 16 cm,diameter: 0.6 mm.
 Perforator, length 16 cm, diameter 0.8 mm
 Footplate burr
 Measuring Rod, length 16 cm, Marker pins at 3 mm, 4 mm, 5 mm
 Holding Forceps, for holding Stapes and Total Prostheses, length 13.5 cm
 Crimping Forceps for Total Prosthesis, length 10.5 cm
 Scissors, for Total Prostheses, length 11 cm
 Micro Hook, 2.5 mm, 45°, length 16 cm
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 61 -
 Diamond Straight Shaft Burr, length 7 cm, Diameter 1.4 mm
 Needle. 16.5 cm, light curve.
 Seeker, ball end angled 45°, 15.5 cm, size 3.
 Suction Cannula, angular, LUER- Lock, working length 6 cm, O.D. 0.7 mm- 2 in
number
 Suction Cannula, angular, LUER Lock, working length 6 cm, O.D.: 1.0 mm- 2 in
number
 Suction Cannula, angular, LUER- Lock, working length 6 cm, 1.3 mm- 2 in number
 Suction Cannula, angular, LUER- Lock, working length 6 cm, O.D.: 1.5 mm- 2 in
number
 Suction Cannula, angular, LUER- Lock, working length 6 cm, O.D.: 2.0 mm- 2 in
number
 Adaptor, for suction cannulas- 2 in number
 Curette, large, spoon sizes 2 x 3.2 mm and 1.6 x 2.6 mm, length 15 cm
11
ADENOTONSILLEC
TOMY
 Curette, small, spoon sizes 1 x 1.6 mm and 1.3 x 2 mm, length 15
ADENO-TONSILLECTOMY
1.BoyleDevis mouth gag- 1 (with full set of tongue blades)
2.Draffin Bipod- 2such
3.Magauran plate-1such
4. Tonsil holding forcep-1such
5. Tonsillar knife with dissector - 1such
6.Mollison’s blunt tonsillar dissector and anterior pillar retractor-1such
7.Serrated tonsillar dissector and anterior pillar retractor- 1such
8.Long straight tonsil hemostatic forceps- 1such
9. Naegus artery replacement forcep- 1such
10.Naegus ligature slipper and knot tier- 1such
11. Eve’s tonsillar snare- 1such
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 62 -
01 set
200.00
12. Long dissecting scissor- straight- 1such
13.Yankauer’s oral suction- 1such
14. St. clair thomson’s adenoid curette with cage- 3 sizes- 1each
15. Long tooth forcep- 1such
16. Quinsy forcep- 1such
12
SEPTORHINOPLAS
TY
01 set
SEPTO-RHINOPLASTY
1. Thudicum’s nasal speculum- 3 sizes- 1 each
2. St. Clair thomson’s long bladed nasal speculum- 3 sizes- 1 each
3. Killian’s self retaining nasal speculum- 2
4. Freer’smucoperichondrium elevator-2
5. Luc’s forceps- 2 sizes- 1 each
6. Killian’s nasal gouge- 1such
7. Tilley’s antral Harpoon-1such
8. Tilley’s antral trocar and cannula-1such
9. Tilley’s Forcep- 1 such
10. Turbinectomy scissors- 1 such
11. Walsham’sforcep- 1 such
12. Asch’s forcep- 1 such
13. 2mm osteotome-1 such
14. 2mm osteotome with guard-1 such
15. 10mm osteotome-1 such
16. 10mm osteotome with gurad-1 such
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 63 -
400.00
17. Mallet-1 such
18. Cartilage scissor-1 such
19. Aufritch retractor-1 such
20. Killian’s ala retractor-1 such
21. Push rasp-1 such
22. Pull rasp-1 such
23. Joseph saw-1 such
13
MICROLAR
YNGOSCOP
Y AND
MICROLAR
YNGEAL
SURGERY
MICROLARYNGOSCOPY AND MICROLARYNGEAL SURGERY
1. Kleinsasser’smicrolaryngoscope- 1such
2. Anterior commisure laryngoscope- 1 such
3. Light cable for laryngoscope-2
4. Riecker’s chest holder
5. Microlaryngeal cup forceps- straight, right turn, left turn, up turn- 1each
6. Microlaryngeal alligator forceps- 2
7. Microlaryngeal scissors- straight, right turn, left turn- 1 each
8. Microlaryngeal blunt dissector with handle- 1 such
9. Microlaryngeal knife with handle- 1such
10.Vocal cord retractor with handle-1 such
11.Microlaryngeal suction- 1 such
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 64 -
01 set
400.00
12. Microlaryngeal suction with diathermy- 1such
14
GENERAL
INSTRUME
NTS
GENERAL INSTRUMENTS
1. AdsonTooth forceps- (5”)-4 such
2. AdsonNontooth forceps- (5”)-4 such
3. Needle holder- (6”/5”/4”)- 6 each
4. Curved needle holder-( 4”)- 4
5.
Mosquito Artery forceps- curved(4”)- 24
6. Medium artery forceps-curved(5”/4”)- 6 each
7. Large artery forceps- curved(7”)- 6
8. Right angle artery forceps- large/medium(7”)- 4
9. Kocher’s artery forceps(6”)- 4
10. Sinus forceps-2
11. Kocher’s gland holding forceps(6”)- 2
12. Babcock’s gland holding forceps(6”)- 6
13. Alle’s tissue holding forceps(5”)- 12
14. Tissue cutting scissors- straight/curved(5”)- 2 each
15. Medium dissecting scissors- curved(6”)-4
16. Small dissecting scissors- curved(4”)- 4
17. Langenberg’s retractor- 4
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 65 -
01 set
200.00
18. Metal suction cannula- 3 sizes( 2.5mm/3mm/4mm)- 4 each
19. Humpy’s knife- 1
20. Malleable sinus probe-2
21. Towel clip- 24
22. Kidney dish( 6”/8”)- 4 each
23. Sponge Holding Forceps (8”)-6
24. Catspaw- 4 pair
25. Gallipot-6
26. Tilley’s Forceps- 4
27. Hartman’s forcep-4
28. Chettle forcep-6
DEPARTMENT OF ORTHOPAEDIC
1
Specification of High Definition Arthroscopy Set:
High
Definition
True High Definition (HD 3 Chip) Camera System 1080p-1 No
Arthrosco
720p, 1080i, 1080p Selectable
Multiple digital outputs (HD & SD Outputs)
py Set
Light source communication
Electronic zoom (in p-modes only)
Autoclavable Camera Head
Shockflex prism mounting
Resolution 1920X1080p,
Light up card edge receptable
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 66 -
01 set
70000.00
Progressive scanning, Aspect ratio 16:9
2 Camera Head Buttons for 4 Remote Fuctions
300W Xenon Light Source- 1 No
Automatically adjust to optimal light intensity
Auto Bulb saver function
Stand by Mode
Homogenized Light distribution
Light Guide Locking Mechanism
OLED Window
Fiber Optic Light Guide Cable 5mm, Autoclavable-1 No
High Definition Monitor- 1 No
24 '' or More Fully High Definition Monitor
Fully compatible with HD and Digital peripherals
Sealed front panel in light-weight design with VESA mount
Wide-screen 16:9 aspect ratio
PIP functionality
Conntrast Ratio-1000:1
Resolution- 1920x1200
High Definition Arthroscope, 4mm, 30 deg, Autoclavable-1 No
Arthroscope sheath- 1 No
5.9mm, Dual Stopcock system, Autoclavable, including Obturator
Shaver Console -1 No
Shaver Console 230 Volt
Capacity to recognize the Hand piece, display of speed
The console should have option for connecting Large Bone Drill & Saw
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 67 -
Handpiece.
Shaver Hand Piece-1 No
500- 12,000rpm,
500- 2,500 cpm, Single and Multi-turn Oscillate
Chuck for small drilling (for shoulder anchors etc) -1 No
Shaver Hand Piece should adapt the chuck
Cutters
Full Radius resector, 4.2mm, 13 cm-6 Nos
Bendable Cutter-6 Nos
Bender for bendable cutter-1 No
Wireless Foot control-1 No
3 pedal foot control
Hand Instruments
Wide bite Straight punch-1 No
Alligator Grasper-1 No
Hook Probe-1 No
90 deg rotary puch,right
90 deg rotary punch,left
Arthroscopic Pump System-1 No
Easy to setup and use.
Flow not less than 2 lt / min.
Pressure ranging 30 - 150 mmHg
Weight should not more than 7 lbs
System should be supplied with auclavable remote control
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 68 -
Inflow / out flow tubing set-10 Nos
Arthroscopy Trolley(Indian)-1 No
The System should be CE/US FDA Approved.
2
C-ARM
SPECIFICATION OF C-ARM MACHINE (IMMAGE INTENSIFIER)
MACHINE
(IMMAGE (C-ARM FULLY MICROPROCESSOR BASED SYSTEM WITH FEATHER
INTENSIFI TOUCH PANAL)
ER)
IMAGE INTENSIFIER:
6 & 9 with high imaging System with high performance capability
CONTROL PANNEL & GENERATOR:
All operation on control panel k-board.
Microprocessor based control with feather touch panel.
Generator unisearch IMD unit.
Excellent fluoroscopy.
Radiography output 25mA. On requirement
Fluoroscopy: foot switch & on the control panel.
Kvp variation of 40 -110kvp.
3 step mode selection, normal (LIH), PULSE and LIVE control.
Digital kvp metering display.
Digital ma metering display.
Foot switch.
X-RAY TUBE HEAD (User Friendly Design):
Duel focus having 0.6mmand 1.8mm focus.
Anode heat storage capacity 30kj.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 69 -
01 set
18000.00
Anode cooling rate250 w/hr.
Type of Generator – khz hf
X-Ray Tube - Fluro 0.6mm X 0.6mm
Focal Spot - 1.5mm X 1.5mm
Fluro / Radio KVP - 40-110kvp
Fluro mA - 0-4 mA
Fluro Timer - 5 Minute
MAS - Up to 200
Power Requirement - 220V/50-60 hz & 3.5 kw
Image Intensifier - 9 Inch
C-ARM FEATURE
Rotation
360Degree
Source to II Distance
90Cms
Arc orbital Movements
110Degree
Pann movements
0-25Degree
Horizontal Travel
22 cms
Vertical motorized movement
32cms
Detachable Cassette Holder (Option) 10” x 12”&8” x 10”
TV MONITORS
15” / 17” Colour (Option)
625 Lines
50-60 hz
High resolution display capability monitor.
MEMORY OPTION
26 frame memory
Computer compatible (Option)
100 frame memory (Option)
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 70 -
3
4
Orthopaedi Orthopaedic Electric Drill System:
c Electric
Drill
System
DIGITAL
ELECTRONIC
TOURNIQUE
T
Driving Unit includes Motor, Stand, foot Control, Flexible Shaft-1Pc, Tool
Kit, Oil Bottle & special container
Cannulated Drill Hand piece max. speed 1200 RPM & with Fixed S.S.Chuck
(0-1/4”)
Reaming Handpiece with Max. Speed 400 R.P.M. Cannulated & AO type
quick coupling.
Drill Chuck Adaptor with Jacob’s Stainless Steel Chuck (USA)
Pistol Grip Sagital Saw (Set of five blades)
Flexible Reamers (2 pieces with reaming pieces 6mm – 13mm)
SPECIFICATION OF DIGITAL ELECTRONIC TOURNIQUET:






Cuff pressure range: 10 to 450mmHg.
Pressure regulation: +/- 10mmHG of set point.
Online Setting: Increase and decrease in pressure settings
Timer: Timer range from 9hours to 59minutes.
Internal least count: Timer 1minute/Internal 1/1000 second.
Alarm & Display Indication: When set pressure is over
 When pressure goes 25mmHg above set pressure.
 When pressure goes 25mmHg below set pressure.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 71 -
04
pcs
(agai
nst
conde
mnati
onof
Batte
ry
oper
ated
drill)
10000.00
04
pcs
2500.00








5
SMALL
FRAGEMENT
INSTRUMEN
T SET
 In battery mode, when battery voltage reaches 9V.
Memory: Pressure set in earlier session is stored and displayed, when
machine is switched on again.
Pressure Table: Maintains set pressure under leak condition.
Backup: 3hours battery backup. (on full charge)
Switch over: Automatic switch over from offline to online (vise versa).
Power: 230V(AC)/50Hz ± 10% (Voltage fluctuations from 180-270).
Stabilizer: Inbuilt.
Cuffs: Different Sizes of five cuffs—washable & easy fitting (Paediatric,
small, medium, big & large).
Digital Display: Digital Display of time elapsed, set time, actual and set
pressure.
SMALL FRAGEMENT INSTRUMENT SET
03
sets
Content List:-i)
Drill Bit Q.C.End 2.5mm Dia—115mm Length—2Pcs.,
ii) Drill Bit Q.C.End 3.2mm Dia—130mm Length—2Pcs.,
iii) Counter Sink—6mm Head—1Pc.,
iv) Quick Coupling Handle—T-Type—1Pc.,
v) Tap with T-Handle for 3.5mm Cortical Screw—2Pcs.,
vi) Tap with T-Handle for 4.0mm Cancellous Screw—2Pcs.,
vii) Drill & Tap Sleeve combined 2.5/3.5mm—1Pc.,
viii)Insert Drill Sleeve 2.5mm—1Pc.,
ix) Screw Driver Shaft Q.C.End ---2.5mm Tip—1Pc.,
x) Hexagonal Screw Driver 2.5mm tip—1Pc.,
xi) Small Depth Gauge—1Pc., Sharp Hook—1Pc.,
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 72 -
1200.00
xii) Small Neutral & Loaded Drill Guide—1Pc.,
xiii)Spanner—11mm—1Pc.,
xiv)
Small Plate Bender—pair—1Pair.,
xv) Plier Cum Wire Bender—1Pc.,
xvi)
K-Wire Bender—1Pc.,
xvii) Reduction Forceps—Serartted---Ratchet Lock—140mm—1Pc.,
xviii) Reduction Forceps—Pointed---Ratchet Lock—140mm—1Pc.,
xix)
Self Centering Bone Holding Forceps—190mm—1Pc.,
xx) Hohmann Retractor 8mm wide, short narrow point, 160mm Length. 2Pcs.,
xxi)
Hohmann Retractor 15mm wide, 160mm Length—2Pcs..,
xxii) Periosteal Elevator ---Straight—160mm length —8mm—1Pc.,
xxiii) Instrument Box with two trays length 300mm—1Pc.
6
LARGE
FRAGEMENT
INSTRUMEN
T SET
LARGE FRAGEMENT INSTRUMENT SET
03
sets
Content List:-i)
Drill Bit Q.C.End 3.2mm Dia—130mm Length—3 Pcs.,
ii) Drill Bit Q.C.End 4.5mm Dia—130mm Length—1Pc.,
iii) Counter Sink—8mm Head—1Pc.,
iv) Quick Coupling Handle—T-Type—1Pc.,
v) Tap with T-Handle for 4.5mm Cortical Screw—2Pcs.,
vi) Tap with T-Handle for 6.5mm Cancellous Screw—1Pc.,
vii) Insert Drill Sleeve 3.2mm—1Pc.,
viii)Drill & Tap Sleeve combined 3.2/4.5mm —1Pc.,
ix) Drill & Tap Sleeve combined 3.2/6.5mm—1Pc.,
x) Screw Driver Shaft Q.C.End ---3.5mm Tip—1Pc.,
xi) Large Hexagonal Screw Driver 3.5mm tip—1Pc.,
xii) Large Depth Gauge—1Pc.,
xiii)Sharp Hook—1Pc.,Spanner—11mm—1Pc.,
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 73 -
1500.00
xiv)
Large Neutral & Loaded Drill Guide—1Pc.,
xv) Pointed Drill Guide with 4.5mm Tap Sleeve & 3.2mm Drill Sleeve—1Pc.,
xvi)
Large Plate Bender—pair—1Pair.,
xvii) Instrument Box with two trays length 300mm—1Pc.
7
BASIC
INSTRUMEN
T SET
BASIC INSTRUMENT SET
03
sets
Content List:--
i) Universal Open Hand Drill –2Pcs.,
ii) Wire Tightner Cum Wire Twister—1Pc.,
iii)
Guide Wire Introducer with Four Pegs—1 Pc.,
iv) Plier Cum Wire Bender Cum Wire Cutter –9” –1Pc.,
v) Wire Cutter Double Action Length 250mmm-1Pc.,
vi) Self Centering Bone Holding Forceps 150mm—1 Pair,
vii) Self Centering Bone Holding Forceps 240mm—1 Pair,
viii) Self Centering Bone Holding Forceps 280mm—1 Pair,
ix) Reduction Forceps –Serrated—Speed Lock—170mm—2 Pair,
x) Reduction Forceps –Serrated—Speed Lock—200mm—2 Pair,
xi) Reduction Forceps –Serrated—Speed Lock—240mm—2 Pair,
xii) Pattela Bone Holding Forceps –Four Prongs—1 Pc.,
xiii) Lane Bone Holding Forcep with Ratchet 200mm—2 Pc.,
xiv) Lane Bone Holding Forcep with Ratchet 170mm—2 Pc.,
xv) Lane Bone Holding Forcep with Ratchet 200mm—2 Pc.,
xvi) Bone Cutting Forceps (Straight) Double Action—190mm –1 Pc.,
xvii) Bone Cutting Forceps (Straight) Double Action—270mm –1 Pc.,
xviii) Bone Cutting Forceps (Curved) Double Action—190mm –2 Pcs.,
xix) Bone Cutting Forceps (Curved) Double Action—225mm –1 Pc.,
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 74 -
1500.00
xx) Chisel with Fibre Handles 5,10,20,30mm --- 1 Pc. Each.
xxi) Osteotome with Fibre Handle Straight 5.10.14.16.20mm—1 Pc. Each.
xxii) Osteotome with Fibre Handle Curved 5.10.14.16.20mm—1 Pc. Each
xxiii) Bone Currette Double ended 4mmx6mm –2Pcs.
xxiv) Bone Currette Double ended 6mmx9mm –2Pcs.
xxv) Langenback Retractor---Small—1Pc.
xxvi) Langenback Retractor---Large—1Pc.
xxvii) Bristow Retractor---1Pc.
xxviii) Self Retaining Retractor—Small—2 pcs.
xxix) Self Retaining Retractor—Medium—2 pcs.
xxx) Self Retaining Retractor—Large—1 pc.
xxxi) Periosteal Elevator Curved—6,10,14,20--- 1 Pc. Each
xxxii) Bone Hammer 200,350,500gms--- 1 pc. Each
8
Large External
Fixator
03
sets
Large External Fixator
















Rod of dia 11 mm in
– Carbon fibre
– lengths 100 – 400 mm
– carbon fibre rod, curved for pelvis
Clamp, clip-on self-holding, MR-safe
Aperture for rods 11 mm
Schanz screw 5mm with lengths 125 – 200 mm
All instruments must be enclosed in a Vario with lid with an insert for Schanz Screws
The instruments should have Combination Wrench of diameter 11.0mm
The instruments should have Socket Wrench of diameter 11.0mm,cannulated
The instruments should have Combination Clamp, clip-on, self-holding, MR-safe
The instruments should have Clamp, clip-on, self-holding, MR-safe
The instruments should have Universal Chuck with T-Handle
The instruments should have Adapter for Seldrill™ Schanz Screw with diameter 5.0 mm
The instruments should have Compressor, open
The instruments should have Short Trocar with diameter 3.5 mm
The instruments should have Long Trocar with diameter 3.5 mm
The instruments should have Handle for Drill Sleeve
The instruments should have Short Drill Sleeve 5.0/3.5
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 75 -
1200.00




9
Medium
External
Fixator
Medium External Fixator






















10
Portable XRay
Machine
The instruments should have Long Drill Sleeve 5.0/3.5
The instruments should have Short Threaded Drill Sleeve 6.0/5.0
The instruments should have Long Threaded Drill Sleeve 6.0/5.0
The instruments should have Connecting Rod  5.0 mm, length 150 mm, Stainless Steel
Rod of dia 8 mm in
o Carbon fibre
o lengths 120 – 320 mm
Clamp, clip-on self-holding, MR-safe
Aperture for rods 8 mm
Schanz screw 4mm & 5 mm with lengths 80 – 175 mm
All instruments must be enclosed in a Vario with lid with an insert for Schanz Screws
The instruments should have Combination Wrench with diameter 8.0 mm
The instruments should have Wrench, hexagonal with diameter 3.5 mm with T-Handle
The instruments should have Combination Clamp, medium, clip-on, self-holding, MR-safe
The instruments should have Clamp, medium, clip-on, self-holding, MR-safe
The instruments should have Drill Sleeve 4.0/2.5
The instruments should have Adapter for Seldrill™ Schanz Screw diameter 4.0 mm
The instruments should have Adapter for Seldrill™ Schanz Screw diameter 5.0 mm
The instruments should have Universal Chuck, small, with T-Handle
The instruments should have Short Trocar with diameter 3.5 mm
The instruments should have Long Trocar with diameter 3.5 mm
The instruments should have Trocar with diameter 2.5 mm
The instruments should have Handle for Drill Sleeve
The instruments should have Short Drill Sleeve 5.0/3.5
The instruments should have Long Drill Sleeve 5.0/3.5
The instruments should have Short Threaded Drill Sleeve 6.0/5.0
The instruments should have Threaded Drill Sleeve 4.0
The instruments should have Long Threaded Drill Sleeve 6.0/5.0
Portable X-Ray Machine
Specification;--MICROPROCESSOR BASED DIAGNOSTIC 50 mA X-RAY MACHINE with following features
 X-RAY TUBE UNIT –Oil filled stationary anode X-ray tube unit with focal spot 2.2 mm x
2.2 mm
 RADIOGRAPHIC OUTPUT –
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 76 -
03
sets
1200.00
01 pc
5000.00
mA
Max mAs
KV
50
250
45-55
40
200
60-75
30
150
80-85
 KV SELECTOR – Select KV from 45 to 85 KV in 5 steps each
 SUPPLY VOLTAGE COMPENSATOR – Adjust supply voltage from 180 v to 250 v
automatically
 LIGHT BEAM DIAPHRAGM
 Electronic DISPLAY – Digital display of mA , KVp & mAs
 OVERLOAD PROTECTOR IN BUILT
 mAs SELECTOR up to 250 mAs
Portable Stand ( can be dismantle Into smaller Parts)
PHYSIOTHERAPY DEPARTMENT
1
2
Combination
therapy Unit
Interferential
therapy unit
Specification
Combination therapy Unit
>Dual channel combi unit for electro and ultrasonic therapy unit.
>0.8/1 & 2.4/3 MHz Multi frequency ultrasonic therapy from same head & depth of penetration
can be adjustable by mixing two frequency.
>Transducer should water resistant head with visual contact indicator &1 to 5 cm2 in
diameter.
>Mounted with trolley with wheel for easy transfer.
>Large colour touch screen monitor(8 inch to 12 inch preferable) for better control.
>Patient encyclopedia with anatomical view(normal,muscular, skeletal).
> Must have I/T curve and S/D curve plotting facility on screen.
>On line help for various common disease.
>Disease wise programmed & manual programmed (neuro-muscular diagnostic &
treatment for paralysis, lymph edema,analgesia,muscle rehabilitation).
>Current form - I.FT, Diadynamic , Russian, galvanic etc.
>Should have vacuum application continuous & pulsed with adjustment of vacuum
strength.
>Must have free memory to save patient data.
>Must have international standard with CE certified.
Interferential therapy unit
> Large colour touch screen display with electrode placement help for better effect.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 77 -
01pc
20000.00
01pc
10000.00
3
Computerize
d Cervical &
Lumber
Traction Unit
4
Electrical NV
& Muscle
stimulator
5
T.E.N.S
Therapy unit
>Spectrum programmed :square/rectangular,Triangle,Trapezoid.
>Treatment mode- Two electrode bipolar static.
Four electrode static interferential
Four electrode dynamic vector.
>Micro computer controlled base frequency & sweep frequency
> On line up gradation facility with SD card.
>Must have real time current sensing system with auto output off during poor contact
for patient safety.
>Should have preprogrammed indication menu, diagnostic programs.
>Must have international standard with CE certified.
>Should have IFT,tens,trabert, ultrariez,& high voltage current in electro therapy preferable.
Computerized Cervical & Lumber Traction Unit
>with bed and standard accessories-1)Traction straps,2)Head halter for cervical
traction,3)spreader bar, 4)Pelvic strap,5)Chin strap.
>Must have four section friction free Traction table with hight adjustable by hydraulic or
electrically.
>Table fitted with wheel for easy transfer.
>Should have max output force up to 90 kg./198 lb,computerized automatic compensation.
>Should have traction speed adjustable(slow,fast,normal).
>treatment mode :continuous/intermittent, harmonized intermittent/progressive.
>Safety system: multiple protection alarm.
>Must have international standard with CE marking.
>Should have treatment time 1-99 minutes.
>Should have digital display.
>Should have international safety standards.
Electrical NV & Muscle stimulator
>Type of current:Galvanic,interrupted galvanic, Faradic, surged faradic,
>IG Pulse width- At least 10,30,100,300 micro sec. 1,3,10,30,100,300 Milli sec.
>Output voltage-0-30 volt & output current-100 Milli amp.
>Timer: Digital timer.
>Buzzer: preferable.
Output indication by digital meter.
Surged Faradic:In rest /contraction period: at least 2-6 sec.
T.E.N.S Therapy unit
>with 4 channel.
>Micro computer based model
>Digital display
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 78 -
01pc
5000.00
01pc
2000.00
01pc
2000.00
>Separate display for each channel intensity &Timer.
>Pulse for TENS International standard:1-200 Hz/sec
>Pulse width International standard:50-200micro sec.
>Output current 1 - 60 ma for each channel.
>Should have preprogrammed indication menu
>Must have real time current sensing system with auto output off during poor contact
for patient safety.
>Mounted with trolley with wheel for easy transfer.
>Should have international safety standard with CE certified.
6
Shortwave
diathermy
atleast 400
watt(micro
processor
controlled)
01 pc
8000.00
Suspension frame
with bed and all accessories
01pc
1000.00
Multi gym or multi exerciser therapy unit
01pc
2000.00
Shortwave diathermy atleast 400 watt(micro processor controlled)
1)High performance solid state generator with digital display.
2)High performance multi jointed arm
3)Continuous & pulsed mode(allows thermal & non thermal treatment)
4)Patient safety switch.
5)Must have CE certified.
6)Safety standard class 1
7)Captive & inductive applicator.
8)Frequency 27.12 Mhz
9)Must have disc electrode with adjustable arm.
10)Pad electrodes for larger ,smaller & irregular surface area(small sinus
electrode preferable)
11)Strap & other standard accessory preferable(knee jt,low back, upper
back.)
Gymnasium Equipments
7
8
Suspension
frame
Multi gym or
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 79 -
multi exerciser
therapy unit
9
Quadriceps
exercise table
10
Parallel bar
adult
11
Static cycle
12
Complex
exerciser unit
Quadriceps exercise table
with quadriceps hamstring torsion arm.
Foam padded table & torque unit with two lever arm,
Adjustable resistance.
Parallel bar adult (height adjustable)
01pc
1000.00
01pc
1000.00
Static cycle
>Dual shock absorber.
>Adjustable tension.
>Digital meter showing- Distance, speed,& calorie.
Complex exerciser unit
should have suitable for shoulder elbow chest abdomen and lower limb exercise should be
gradeable and adjustable for resistance foam padded table top on tubular frame the unit should
be dimension 185-195 X 70-80 cm wide and the height should be 80 -85 cm complete unit
consist of one table pan assembly and following attachement - ankle, hip, wrist,knee,abdominal
and back exerciser it should include strap, harness,and over head pulley systems different iron
weight plates starting from 0.25 kg and 1 kg total upto 30 kg pelvic rest 1 quadriceps rest
1 supination pronation wheel 1 wooden cabinet for storage
01pc
200.00
01pc
2000.00
01pc
2000.00
Physical Fitness Equipments
13
Treadmill
Treadmill >Motorized at least 125 kg capacity,
>AC motor : capacity >_2.0 H.P (peak>_4.0 H.P)
>speed 1-18 kph,
>Incline 0-16%,
>convenient hand controlled speed &incline.
>Quick speed, quick incline.
>Easy incline, 5 program upland running.
>Diverse speed & incliner program.
>Self stop.
OCCUPATIONAL THERAPY
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 80 -
14
Fluidotherap
y
Fluidotherapy
01pc
1000.00
it should be used for double extrimity simaltaneously
operated in pulse or continious mode
treatment time adustable
adustable air speed
machine should mounted with wheel or trolley
safety standard class 1
digital display
should have dry heat media (cellulose particles) with the machine as accessories
For hand exercise & rehabilitation
Finger Goniometer
01pc
500.00
16
Finger
Goniometer
Goniometer
Goniometer
01pc
500.00
17
Peg board
Peg board
01pc
500.00
18
Wrist
circumductor
Grip exerciser
Wrist circumductor
01pc
500.00
Grip exerciser
01pc
500.00
Finger
exerciser
Table
Finger
dexterity
board
Hand Gym kit
board
Finger exerciser Table
01pc
500.00
Finger dexterity board
01pc
500.00
Hand Gym kit board
01pc
500.00
15
19
20
21
22
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 81 -
500.00
General exercise items
Over head
pulley
Inclined
sanding board
Horizontal
sanding board
Shoulder
wheel
Balance board
Over head pulley
01pc
500.00
Inclined sanding board
01pc
500.00
Horizontal sanding board
01pc
500.00
Shoulder wheel
01pc
500.00
Balance board
01pc
500.00
Foot
placement
ladder
Bolster set
Foot placement ladder
01pc
500.00
Bolster set
01pc
500.00
Wedge board set
01pc
500.00
Quadriceps table
01pc
500.00
32
Wedge board
set
Quadriceps
table
Stand in frame
Stand in frame
01pc
500.00
33
Trampoline
Trampoline
01pc
500.00
34
ADL training
kit
Low rise
exercise
platform
Cp prone
stander
Cp chair
ADL training kit
01pc
500.00
Low rise exercise platform
01pc
500.00
Cp prone stander
01pc
500.00
Cp chair
01pc
500.00
Wheel chair
for transfer
training
Wheel chair for transfer training
01pc
500.00
23
24
25
26
27
28
29
30
31
35
36
37
38
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 82 -
39
Multiple gym
exerciser
Multiple gym exerciser
01pc
DEPARTMENT OF MICROBIOLOGY ESI-PGIMSR, JOKA
01pc
1
Real time
SPECIFICATIONS
Real time Polymerase Chain Reaction (PCR) System with Qualitative and
Polymerase
Quantitative detection
Chain
Reaction
a. The Real time PCR System must have International and/or National quality and
(PCR)
safety certification, e.g. CE and/or UL/cUL and/or ISI certified and IVD certified.
System with
b. The Real time PCR System should be an open platform system, and must have
Qualitative
provisions for using third party kits and reagents for the molecular diagnosis of
and
infectious diseases.
Quantitative
detection
c. The Real time PCR System must at least have the following In vitro Diagnostics
approved kits available from the same manufacturer which are pre-validated on
the quoted model :
i. Human Immunodeficiency virus
ii. Hepatitis B virus
iii. Hepatitis C virus
iv. Cytomegalo virus
v. Ebstein Barr virus
vi. Herpes Simplex virus
vii. Mycobacterium tuberculosis
d. There should be provision for using the system as simple Thermocycler for
qualitative molecular detection of infectious diseases.
e. The Automated Real time PCR System should be accompanied with a desktop or
laptop computer and printer system (required for the functioning and data storage
and printing of reports) with original operating system and free software support
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 83 -
500.00
36000.00
for the lifetime of the machine.
f. The Automated Real time PCR System should have already been installed in at
least two (02) reputed Academic and / or Medical institutions and / or reputed
accredited diagnostic laboratories in the Eastern region of India.
g. Technical Parameters:
Features
Specification
Thermal Cycler Air based heating and cooling mechanism for maximum uniformity
with even heating and cooling.
Mechanism
Sample Layout Should be flexible for the tube input volumes having capability of
running 96 or more samples.
Any additionalstep of centrifugation of tubes while performing the
Additional
assay should NOT be there.
Intra-assay
Centrifugation
Should have uniform temperature distribution. Should maintain isoUniformity
optical detection in all wells for maximum uniformity. Temperature
uniformity should be in the range of ±0.02oC.
Should come with standard chemistries for gene expression,
Chemistries
quantification, mutation scanning, genotyping and methylation
studies.
Temp Range
Up to 99℃
Different LED’s with 5 different wavelengths with minimum crossLight Source
talks (one LED with one wavelength). The assay should not be based
on onesingle wavelength of light.Should be able to detect all wells
equally with same optical path length.
Warranty on light source for minimum of 10 years.
Light Source
Lifespan
Should be minimum 5 plex. Should have capability of further
Excitation
increasing the multiplexing beyond 5-Plex in singe tube.
Plexing
Dynamic Range Should be of 10 orders of magnitude
10 µl-100 µl
Reaction
Volume
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 84 -
Passive
Reference
Required?
Tube Format
Software
In vitro
diagnostics
Approval
2
Automated
(Multicapilla
ry) Capillary
Electrophore
sis System
Should NOT require any passive reference dye
Should be able to mark the caps of the tubes. Should have flexible
tube format. NOT CAPILLARIES.
Unlimited user Software license with maximum feature should come
absolutely free of cost for the life of the machine.
Real Time In vitro Diagnostics approved validated kits on quoted
model as mentioned above should be available with instrument
manufacturer. Instrument should also be In vitro diagnostics certified
for use in diagnostic laboratory.
Automated (Multicapillary) Capillary Electrophoresis System:
a. The automated multicapillary electrophoresis System must have International
and/or National quality and safety certification, e.g. CE and/or UL/cUL and/or IVD
certified and/or ISI certified.
b. It should be a fully automated capillary electrophoresis system for fragments of
DNA and RNA, which is based on high throughput nucleic acid analysis of at least
60 samples in one run within 30 minutes.
c. System should comewithReady-to-rungelcartridgesallowing samplesto be
analyzed replacing laborintensiveagarosegel electrophoresiseliminating the need
for handling carcinogenic compounds likeethidium bromide.
d. Post PCR samples should be directly analyzed for fragment analysis using the
system without prior purification of samples.
e. The instrument should be usable for genotyping, restriction digestion, qualitative
monoplex or multiplex PCR, PCR-based cDNA library screening and other routine
molecular biology applications.
f. System should work with an input volume of equal or less than 1 μl offering a high
sensitivity ofupto 1000pg.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 85 -
01pc
36000.00
g. Instrument should come with user-friendly analysis software including an
accompanying Laptop with original operating system and free software support and
upgradation for the lifetime of the instrument.
h. The Real time monitoring of the sample analysis should be visible on the computer
screen.
i. Operating temperature : 20-28°C
j. Excitation Source : light-emitting diode (LED)
k. Detection Source : Photomultiplier Tube
l. The instrument must eliminate the need for a separate Gel Doc system after
Electrophoresis.
m. The instrument should be able to provide Standardized and accurate analysis with a
resolution down to 5 base pairs.
3
02pc
Biosafety
Biosafety Cabinet: Class II Type A2 with accessories:
Cabinet:
a. The Biosafety cabinets must have International and/or National quality and safety
Class II Type
certification, e.g. CE and/orUL/cUL-listed and/or ISI certified.
A2 with
b. Class II Type A2 biological safety cabinet with factory installed programmable UV
accessories
light for surface disinfection.
c. Standard 4 ft model: Exterior dimension preferably not to exceed, 52 X 64 X 33
inch (W X H X D) ± 10%
d. Double Blower system; Brushless DC motor technology for saving energy
consumption.
e. SmartFlow Indicator, with Digital airflow verification technology (The balance of
downflow and inflow should control the cleanliness and containment – preventing
room contamination from reaching the BSC work surface and keeping any
biological hazards in the BSC work area from escaping out the front opening.)
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 86 -
10000.00
f. Ergonomic design with 10° Slopped front, preferably with Armrest.
g. Supply / exhaust air filter specification: H14 HEPA or better. The HEPA or ULPA
filters shall capture contamination in the room air and in air drawn from the BSC
work area to create clean downflow and the exhaust air.
h. Service Valves (through side walled access ports)
i. Receptacles in the Rear Wall: load capacity of up to 5A
j. Smart Clean front window Design easily lowered for cleaning of inner surface &
protects operator.
k. The provider must provide at least two (2) ergonomically designed compatible,
height adjustable hydraulic or screw turn low back support revolving stools with
each Biosafety cabinets for user operations.
4
Micropipette Micropipettes (0.5-10μL set, 10-100μL set, 100-1000μL set) with disposable Tips and 02
sets
s (0.5-10μL autoclavable boxes.
set, 10-100μL
a. Each set shall contain 3 adjustable volume Fully autoclavablemicro pipettes of the
set,
100following ranges:
1000μL set)
i. 0.5 - 10μl
with
disposable
ii. 10 - 100μl
Tips
and
iii. 100 - 1000μl
autoclavable
boxes.
b. Six (06) reusable T.I.P.S boxes with 96 Pipette tips in each boxes; Three pairs of
boxes are to be compatible to the above three different sets of Micro pipettes.
c. The boxes and the tips should also be fully autoclavable.
d. The micropipettes should have Spring Loaded Tip Cone for improved ergonomics
which should be tight fit to the tip.
e. Adjustment opening to adjust the pipettes to a specific liquid and volume.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 87 -
2000.00
f. Control Button with very low operating force, positioned for perfect ergonomics.
g. Ejector withvery low operating force, positioned for perfect ergonomics.
h. Volume Display: 4 Digits with magnification.
i. There should be quick connection clip toremove lower part easily.
5
01pc
Vortex Mixer Vortex Mixer (with accessories):
a. Digital vortex Mixer for Molecular Biology Applications with International and/or
National quality and safety certification, e.g. CE and/orUL/cUL-listed and/or ISI
certified.
b. Should be ideal for applications demanding repeatable results.
c. Variable speed control at least from 500 to 3000 rpm. A higher range is allowable.
d. Touch keypad controls and LED display for speed and time. Not merely Analog
controls, for ensuring reproducibility in molecular diagnostics.
e. Microprocessor control to maintain set speed for consistent mixing.
f. Timer displays elapsed time; auto shutoff at end of cycle.
g. Should be allowable to be used in 220 to 240 V and 50/60 Hz electrical supply.
h. Should have robust durable electrical connectivity conforming to standard Indian
sockets.
i. The following accessories have to be quoted along with the vortex mixer, which
can be steadily fitted and connected with the mixer:
I. 24 to48 numbers vertical Microtube Holder for mixing 0.25 to 2.0mL
microcentrifuge tubes / PCR tubes or high-density foam inserts to
accommodate 24 to 60 microtubes.
II. Vertical tube holder for mixing at least four (04) 50 ml tubes together.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 88 -
1000.00
III. Vertical tube holder for mixing at least four (04) 5 ml (09 to 13 mm diameter)
tubes together.
6
Molecular
grade DNAse
RNAse free
Water
Purification
System
01pc
Molecular grade DNAse RNAse free Water Purification System
a. The entire water purification system should be equipped with three part
equipments, quoted together by the same bidder, including:
i. A Pretreatment Water filtration reverse osmosis system
ii. A Pretreatment Iron, hardness and particleremoval system
iii. A Molecular grade Water purification system proper.
b. The Pretreatment Water filtration reverse osmosis system (i) and the Pretreatment
Iron, hardness and particle removal system (ii) must have National and/or
International quality and safety certification, e.g. ISI and/or CE and/or UL/cUL
certified.
c. The Molecular grade Water purification Systemproper (iii) must have International
and/or National quality and safety certification, e.g. CE and/or UL/cUL and/or ISI
certified.
d. The Pretreatment Water filtration reverse osmosis system (i) and the Pretreatment
Iron, hardness and particle removal system(ii) should be able to be connected in
series connection, directly from the pipeline ground-water feed and should be able
to deliver output water quality compliant to the acceptable limit of the feed water of
the Molecular grade Water purification system proper(iii) as mentioned below in
tight fitted series connection.
e. The Pretreatment Water filtration reverse osmosis system (i) and the Pretreatment
Iron, hardness and particle removal system(ii) should be able to deliver at least
15litres of water per hour to the Molecular grade Water purification system
proper(iii).
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 89 -
30000.00
f. The Pretreatment Water filtration reverse osmosis system (i) and the Pretreatment
Iron, hardness and particle removal system (ii) should at least be equipped with the
following technology:
i. * 2 Stage pretreatment system
ii. * 5 micron and 1 micron wrapped type depth filter
iii. * 3 Pressure gauges
iv. * Less than 50 Db noise levels
v. * Automatic low/high pressure cut off
vi. * DC pump with 0-2 pressure at 120L /hr
vii. * Inlet screen filter to DC pump
viii. * Optional filters : 0.5 micron
ix. * Optional filters : Activated carbon
g. The Molecular grade Water purification system proper (iii) should be able to
deliver the required quality of pure and ultrapure water from its feed water
acceptance level of:
1) 2000micro Siemens conductivity
2) Fouling Index (SDI) < 12
3) Total Chlorine < 3 ppm and
4) TOC <2000 ppb
h. The Molecular grade Water purification system proper (iii) should beable to deliver
reagent Grade Type 2 water (pure quality) and Reagent grade Type 1 standard
water (ultrapure quality) as defined by standard international quality control
organizations like ISO:3696 standards and / or Clinical and Laboratory Standards
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 90 -
Institute-Clinical Laboratory Reagent Water standards and / or ASTM standards.
i. The Molecular grade Water purification system proper (iii) should have two
different points of delivery. It should be able to deliver through one point of
delivery, reagent Grade Type 2 water (pure quality) bacteria and pyrogen free
water, which may be used for basic laboratory needs, such as buffer and reagent
preparation, microbiology media preparation, histology and rinsing of glassware of
the following grade:
Type 2 Pure grade Water outlet
Parameter
Value
Resistivity, Mega Ω @ 25 °C
10 – 15
Programmable water flow rate / minutes
̴01
TOC, ppb (μg/l)
< 30
Bacteria, cfu/ml
< 10, reducible to
< 0.1 *
<1*
Particulates > 0.22 μm, Particulates/ml
Silica rejection
99.9%
Pyrogens (endotoxins), EU/ml
< 0.001 **
RNases, ng/ml
< 0.01 **
DNases, pg/μl
< 4 **
(*) With special filter for microbiological grade water
(**) With special filter for molecular grade water
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 91 -
j. The Type 2 water (pure quality) production system / chamber of the Molecular
grade Water purification system proper (iii) should be enabled at least with the
following technologies:
1) Pretreatment cartridge
2) Reverse Osmosis with a high flux polyamide membranewith 94- 99% ion
rejection backed by Pump with temperature feedback mechanism so that
the flow rate should be 3 ltr/hr at room temperature .
3) Electro Deionization with
auto regeneration by electric current,
eliminating the need for chemical regeneration or replacement of DI
resin cartridges with carbon beads at cathode of the EDI module to
prevent scaling inside of the module
4) Activated Carbon cartridge
5) UV lamp with 254 nm Wave lengthbefore entering the tank
6) Recovery loop
water wastage
with capillary tube and diaphragm valve to minimize
7) Carbon beads at cathode of the EDI module to prevent scaling of the
module
8) Permeate divert valve which will divert low quality water to the drain
9) Coaxial resistivity cell with a flow through design and a cell constant
of 0.01cm-1
10) Display both compensated and non-compensated temperature accurate
within ±0.1°C.
11) The reservoir tankshould be blow moulded, cylindrical PE reservoir
with a conical bottom and opaque walls with a minimum of 30 litres
capacity.
12) Sensor rod float switch, programmed to have high and low level cut-off
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 92 -
based on water level in the tank.
13) The reservoir tank should possess a tank vent filter made of soda lime,
activated carbon and 0.22 micron hydrophobic membrane to trap
contaminants present in atmospheric air.
14) The Point of Delivery units should be of adjustable height and rotating
arm-adjustable to any glassware.
15) There should be multicolour monitor displaying resistivity, TOC, level of
water in reservoir, volume dispensed etc.
k. The Molecular grade Water purification system proper (iii) should also be able to
deliver through a different point of delivery, Type 1 water (ultrapure) DNA, RNA,
DNAse, RNAse free water for molecular biological applications, suitable for
genomics applications (quality at least equivalent to DEPC-treated water) and cell
culture of the following grade:
Type 1 Ultrapure Molecular grade Water outlet
Parameter
Value
Resistivity, Mega Ω @ 25 °C
Around
18.2 (> 18)
Programmable water flow rate / minutes
̴ 0.05 to 2
TOC, ppb (μg/l)
<5
Bacteria, cfu/ml
< 0.1 *
Particulates > 0.22 μm, Particulates/ml
<1*
Pyrogens (endotoxins), EU/ml
< 0.001 **
RNases, ng/ml
< 0.01 **
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 93 -
DNases, pg/μl
< 4 **
(*) With special filter for microbiological grade water
(**) With special filter for molecular grade water
l. The Type 1 water (pure quality) production system / chamber of the Molecular
grade Water purification system proper (iii) should be enabled at least with the
following technologies:
1) Water source feed should be a closed connection from the Type 2 water
reservoir tank eliminating any possibilities of contamination.
2) Re-filtration through two stage mixed bed ion exchange and activated
carbon cartridge to remove ionic and organic contaminants to trace
levels.
3) Low pressure mercury vapour lamp made of quartz with 185/254 nm dual
wavelength UV lamp.
4) Should contain high-precision resistivity meters with following featuresa. Coaxial electrodes to warrant cell constant stability.
b. Low cell constant (0.01 cm-1) for optimum measurement accuracy
of low ionic contamination
c. Temperature measurement with a 0.1 °C resolution for proper
report of temperature compensated resistivity
5) Should contain a built in TOC monitorwith a Quartz celland UV lamp
which should accurately measure online TOC from 1- 999 ppb.
6) To prevent deterioration of water quality during periods of non-use, the
ultrapure water system will be able to recirculate water to maintain high
water quality.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 94 -
7) Special filter packs for ultrafiltration and DNAse RNAse removal at the
point of delivery or dispensing unit.
8) Controllable & user login password protected dispensing unit for Type 1
ultrapure water with ultrafiltration cartridge at the collection end with
Log Reduction Value between 5.6 and 7.65 over challenge range of 220
and 22000 Eu / mL.
m. To avoid maintenance errors and to improve traceability, the internal primary
consumable water purification cartridges should have a built-in RFID tag.
n. To comply with Standard requirements, the resistivity meter shall be able to display
the non-temperature-compensated resistivity.
7
Automatic
Electronic
Laboratory
Balance
Automatic Electronic Laboratory Balance
01pc
400.00
01pc
400.00
a. The Electronic Laboratory balance should have International and/or National
quality and safety certification, e.g. CE and/or UL/cUL-listed and/or ISI certified.
b. The maximum weighing capacity should be 500 grams with a tare range of 0 to 500
gm. A higher range is allowable.
c. The minimum readability should be 0.1 mg differences.
d. The balance should be fitted with durable electrical connectivity compatible to
Indian electrical standard sockets and operable in 220 to 240 V and 50/60 Hz
electrical supply.
e. The balance plate should be covered with High draft shield fibre / glass covers with
mounted front and rear fibre / glass panels, including sliding doors.
f. The balance should have digital electronic display and preferably soft touch
controls for Power, Tare and calibration options.
8
Carbon
Carbon dioxide (CO2) Incubator:
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 95 -
dioxide (CO2)
Incubator
Technical specifications
1. CO2 Incubator with work chamber volume approx. 150 to 190 liters / 5.3 to 6.5 cu.
ft (± 10%).
2. Air jacketed heating system with temperature control by microprocessor.
3. Temperature range from ambient +3 o C to + 55 o C.
4. Temp. Deviation with respect to time is + 0.1K.
5. Continuous air Contamination prevention by in chamber Class 100 HEPA Air
Filtration.
6. Event based Decontamination with in-built moist heat High temperature cycle, with
ease operability, preferably single switch operation of sterilization cycle. The built-in
automatic decontamination facility to remove bacteria, fungi, spores, mycoplasma etc
without removing sensor, fan or any other fitting. The system should employ automatic
decontamination routine at moist heat of 90o C or equivalent.
7. CO2 control by Microprocessor based & by heat resistant Thermal Conductivity
detector to withstand heat of decontamination.
8. CO2 range 0 to 20% or better and CO2 accuracy + 0.1% by volume.
9. System should have Interactive Control with Touch screen for rapid access of
important information for each critical parameter in the Incubator.
10. Humidity range should be 95% rH or higher. Recovery time for humidity loss during
door opening for 30 seconds upto 96% rH of initial value should not be more than 20
minutes.
11. At least 3 nos. stainless steel perforated shelves should be supplied.
12. It should be supplied with access port to allow any cable, plug or tubing to be
easily inserted into or out of the chamber.
13. Interior chamber should be made of stainless steel with electropolish finishing of inner
surface with rounded corners on all sides for easy cleaning. The shelves and fan
impeller also should be made of stainless steel and should not have nuts or bolts
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 96 -
for shelf supports to reduce the scope of growth of contamination. No plastic parts
should be inside to avoid VOC.
14. Built-in audible and visual water level alarm should be available when the water
reservoir (water tray less system to avoid contamination) needs to be refilled to
ensure a constant high level of humidity and to prevent cultures from drying out.
15. Independent electronic over temperature protection with separate sensor should be
available for sample protection.
16. The system should have large digital display for both temp. & CO2 simultaneously.
17. System should have at least two doors, one main door and one glass doors.
18. Suitable for 230V, single phase 50Hz operation.
19. Suitable servo voltage stabilizer with high voltage low voltage cut off circuit,
auto reset with delay timer and spike eliminator etc.
20. Double stage CO2 pressure regulator with stainless steel diaphragm.
21. 18Kg CO2 Cylinder filled with CO2 gas 99.5% or better purity required for operation
of CO2 Incubator, along with cost of refill should also be quoted.
9
Hot air oven
02
pcs
Hot air oven
Technical specifications
1. Should be CE certified internationally quality control approved instrument.
2. Corrosion-resistant galvanized steel chambers.
3. Digital display and timer facility
4. Upper temperature cut off ( automatic)
5. Microprocessor temperature control.
6. At least 2 tilt proof wire-mesh shelves
7. Chambers and heating elements should made of corrosion resistant steel.
8. Chambers should be easy to clean.
9. Volume minimum 75 litres
10. Operating temperatures from 50° to 250°C.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 97 -
2500.00
11. Easy to use, microprocessor-controlled touch button operation.
10
Automatic Evacuation-replacement system for the culture of anaerobes, capnophiles, 01pc
Automatic
Evacuation- and microaerophile:
1. Automatic evacuation-replacement system with at least One to Three (1-3) gas
replacement
inlet connections: CO2, H2, and O2 and One to Four (1-4) jar outlet connections.
system for
2. The System should be internationally quality control certified, e.g. CE / ISO / ISI
the culture of
certified.
anaerobes,
3. The System should have pre-programmed functions with easy to use, preferably
capnophiles,
single touch key operations for preparing Anaerobic, Microaerophilic and
and
Capnophilic culture conditions.
microaerophil
4. Following associated transparent Polymethylmethacrylaat (PMMA) jars with
e
Gas tight fit by means of a snap-shut adaptor on the lid of the jar and stainless
steel petri dish holders of the following dimensions are required to be supplied
along with:
a. Two (02) equivalent jars:
Diameter and height: Ø =123mm, h=240mm (±10%)
Volume: 2.75 L (±10%)
Contents: 1 stack of 12 Petri dishes with Ø 9-10cm (±10%)
b. Two (02) numbers of Petridish holders:
Petri dish holder for 12 Petri dishes with Ø 9/10cm made of stainless
steel
c. Two (02) equivalent jars:
Diameter and height: Ø =175mm, h=240mm (±10%)
Volume: 5.65 L (±10%)
Contents: 1 stack of 12 Petri dishes with Ø 14.5cm (±10%)
d. Two (02) numbers of Petridish holders:
Petri dish holder for 10 Petri dishes with Ø 14.5cm made of stainless
steel
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 98 -
4000.00
5.
6.
7.
8.
9.
e. One (01) number micro well plate holder:
Holder for micro-well plates of 9 x 13 cm, made of stainless steel
f. One (01) equivalent jars:
Diameter and height: Ø =230mm, h=240mm (±10%)
Volume: 9.66 L (±10%)
Contents: 3 stack of 12 Petri dishes with Ø 10cm (±10%)
g. One (01) number of Petridish holder:
Petri dish holder for 3 x 12 Petri dishes with Ø 9/10cm, made of stainless
steel, to be fitted in the height of 240 mm jar.
Palladium coated catalyst pouches ideal for the big jars:
a. SIX (06) Sets of catalysts, ideal for the big size jars are to be provided
along with, which can be easily re-used by reactivation in Hot air oven.
Reducing valve: To reduce the pressure in the gas cylinder to the system
working pressure, a reducing valve has to be provided with the gas cylinder(s).
This must be a 2-step reducing valve, preferably calibrated and supplied by the
same manufacturer, which has manufactured the Automated evacuationreplacement system. The working pressure should be adjustable to 1.8 Bar or 26
psi.
Option of user programming function (free user programming of oxygen level,
gas mixture and evacuation level) should be there.
Option for Preprogrammed recipe for oxygen level, gas mixture and evacuation
level should be there.
The bidder should also quote for 18Kg CO2, H2, and O2 Cylinders filled with
CO2, H2, and O2 gases 99.5% or better purity required for operation, along with
cost of refill should also be quoted.
DEPARTMENT OF DENTAL
1.
Chair Unit
Specifications of dental Equipments /Instruments of newly Developed upcoming Dental
Surgery
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 99 -
01
each
10000.00
1. Chair Unit : Electrically operated programmable chair, both hand and foot control
operation, over hanging delivery unit, spittoon with auto flush, High and low intensity
operating light, motorized suction (with auto drain) X-ray viewer, three way syringe, zero
backache doctor’s stool.
a) Light cure unit : Light emitting diode (LED)
b) Air rotar with Controlled box : along with
(i) Air compressor: Minimum 1.5 HP, Oil free
(ii) Air rotor Hand piece: 2 to 3 Lakhs RPM
2
Dental Electro
Surgery Unit
with multiple
tips
3
4
Dental Electro Surgery Unit with multiple tips
01
pc
1000.00
Automatic
Automatic dental X-ray film developer –IOPA (Intra oral Peri apical radiograph) automatic processor
dental X-ray film
developer –IOPA
(Intra oral Peri
apical
radiograph)
automatic
processor
01
pc
1000.00
Lead apron for
use along with
dental X-ray unit
01
pc
100.00
Lead apron for use along with dental X-ray unit
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 100 -
5
Electric High
Speed Micro
motor
6
Ultrasonic Scalar
Electric High Speed Micro motor of about 35000 RPM with reverse forward switch, foot 01
control, with Both straight and contra angle Hand Piece.
pc
5000.00
Ultrasonic Scalar : with four tips
02
pcs
100.00
01
pc
20000.00
DEPARTMENT OF BLOOD BANK
1
Automated
Immunohem
atology
detection
system
Specification
Automated Immunohematology detection system by Gel Card Technology.
1. Semi-automated immunohematology analyzer incorporated with centrifugation, reading and
interpretation abilities for the tests performs by the column agglutination technology for
transfusion related cross matching on anti human globulin and enzyme phase (to detect both IgG &
IgM antibodies), blood grouping, partial Rh-D typing, antibody screening &identification in a
single step.
2. The following range of investigations must be provided in the system.
i. ABO Blood grouping with partial D screening.
ii. Weak anti D test with ICT method.
iii. Antibody screening and identification.
iv. Single antigen test cards and antisera for Rh-C/c, E/e, Cw, Kell, Fya, Fyb, Jka, Jkb, Lewisa Lewisb,
Lutherana, Lutheranb, MNS, etc.
v. Special gel cards for antihuman globulin test positive IgG, IgM, IgA, C3d, C3c etc.
vi. Provision for acid elution method.
vii. Special blood grouping cards for donor and recipient for DVI variant.
viii. Syphilis antibody detection.
Detail procedure for all compatible methodologies mention as above must be provided.
3. Automated card reading and report generation with bar code security.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 101 -
4. Expression of results in grades of agglutination.
5. Capacity for 20 – 24 gel cards with ‘V’ bottom tubes in single run.
6. Peltier heating of incubator with programmable controls for 15 minutes and digital display of
temperature.
7. Centrifugation force with 80 – 84G.
8. Clear transparent top for centrifuge and incubator with rust and corrosion resistant body.
9. The system must be devoid of any wash phase.
10. Incorporated capabilities for validation storage and reproduction of results.
11. Parallel computer connection with bidirectional portability and appropriate software to be provided
along with the equipment.
12. Compatible printer for printing of different data and customized report to be provided along with
the equipment.
13. A quality control system must be incorporated in the equipment for all the lab.
14.
i. Provision for 2 and 3 red cell panel for antibody screening, 11 cell panel for antibody identification
and pooled ‘O’ cell with known phenotype for donor screening as per NACO Guidelines.
ii. Provision for NaCl/Enzyme and cold agglutinins cards, modified bromelin solution, papain, cell
stab, cell thaw and cell freeze reagent.
15. CE/ISI compliance of the system.
2
BLOOD
BANK
REFRIGER
ATOR
BLOOD BANK REFRIGERATOR
Nomenclature: Frost Free See-Through Door Blood Bank Refrigerator approx. 300 Litre
capacity.
Description:
1.Uniform temperature maintains within temperature range of 4°C ± 2°C with ± 1°C variation.
2. The system should have provision to prevent moisture condensation in humid weather.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 102 -
02
pcs
10000.00
3. The cabinet constructed of minimum 10 gauge steel, CFC free urethane refrigerant insulation,
seal self-closing single glass door, key- lock, mounted on durable castor wheels, provision of
automatic evaporation of condensate
4. Internal CFL lighting with control mounted switch as standard.
5. Built-in temperature sensor, recorder and control unit.
6. There should be visual display of line, Power, Compressor, Heater, System OK, Battery
Indicatior, Chart Change and alarm for audio-Visual display of Tempearture, Door open,
Powder failure, sensor faliure.
7. Battery back-up for two hours for temperature recorder in case of power failure.
8. In-built calibrated digital temperature sensor.
9. Sliding trays (stainless steel), removable type.
10.CE Certification.
N.B. This specification is not meant for Laboratory grade commercial or modified commercial
refrigerator .
Essential accessories must be supplied with the main consignment :
1. Power cord Indian type.
2. Seven day electronic chart recorder with battery back-up.
3. UPS of appropriate capacity and CVT (if not in-built provided)
DEPARTMENT OF PATHOLOGY
1
Fully
Automated
Urine
Analyzer
Fully Automated Urine Analyzer
1. Random access system for physical, chemical and sediment analysis on urine specimens.
2. Multiparameter Chemistry analysis of at least 10 parameters including:
(a) Specific gravity
(b) pH
(c) Albumin
(d) Glucose
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 103 -
01
pc
40000.00
(e) Ketone Bodies
(f) Bilirubin
(g) Urobilinogen
(h) Blood/Hemoglobin
(i) Micro albumin
(j) Nitrite
3. Analysis of standard urinary sediments consisting of different cells, casts and crystals.
4. Throughput-60/hour including sediment analysis in random access mode.
5. Microprocessor based photometric analysis of chemical parameters and flat flow cell technology
with high speed and 800-1000 frame imaging for sediment analysis.
6. Interconnected parallel pc with appropriate soft ware for –
 Retrival of analysis data
 Display of analysis data
 Image display of formed elements
 Storage of data of results and others atleast 10,000 in number
7. Bar coded facility for reagent and sample identification
8. Laser colored printing of results and data
9. Power back up with UPS for at least 2 hours
10. Accessories
a. Sample rack to hold 50 samples-05
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 104 -
b. Reagents for start up- 1000 analysis
c. International certification for medical equipments
2
Bone decalcifier
automated,
electrolytic
decalfication
system
3
LBC
01
pc
2000.00
01
pc
30000.00
01
Patient and Patient and data management system for laboratory services
1. Fast processing system with high end security having several different modules for patient and pc
data
data management of the laboratories.
managemen
40000.00
Bone decalcifier automated, electrolytic decalfication system, holding capacity for 30
cassettes and at least 700ml decalcifying solution, digitally controlled.
Specifications for LBC
1. Automated system for processing of Gynaecological and non- gynaecological cytology
samples for liquid based cytology along with automated stainer.
2. Should have ability to make single slides which is uniform and reproducible.
3. Should have a controlled membrane transfer technology to make a thin smear with
uniform distribution of cells.
4. System should allow residual material to be used for ancillary testing such as HPV,
CT/NG, Immunocytochemistry, Special Stains, cell blocks etc.
5. Should have an automated slide stainer with an ability to run at least 30 slides in half an
hour.
6. UPS with two hour power backup.
7. CE certificate
Accessories:
1. Microscopic slides- 2 boxes of 100 slides
2. Filter- 2 box to process 200 samples
3. Solution -2 box to process 200 samples
4. Preservative solution -2 box to process 200 samples
5. Staining kit for staining at least 200 smears
6. All the standard accessories to be provided with the equipment.
4
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 105 -
t system
2. Should have the ability to generate unique identification number of the patient starting from lab
registration, sample collection, testing and report delivery with generation of bar code id, and
stickers.
3. An integrated token system for the patients while waiting for sample collection.
4. Computer with bar code reader in registration, sample collection, different labs ( clinical
pathology, Cytopathology, hematology, histopathology, different sections of biochemistry and
microbiology)
5. Easy to operate
6. Ability to store data of at least 5000 patients per day.
7. Data to be accessible on mobile, laptop, tablets etc and the ability to deliver SMS to target
people(patients as well as doctors).
8. Result modification before final report delivery.
9. Can be integrated with other automated lab equipments.
10. New features can be upgraded time to time as per requirements
11. Accessories for the system to be supplied along with the software.
5
Automate
d Cover
Slipper
Automated Cover Slipper
1. Fully automated unit with a through put of 400 slides/hr. at least
2. Should be compatible with different sizes and thickness of cover slip as
written below.
(a) Size – 40mm, 50mm, 55mm, 60mm.
(b) Thickness – 0.13 – 0.17mm.
3. Should be compatible with different solvent like xylene, d-limonene and
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 106 -
01
pc
40000.00
aliphatic hydrocarban –based substitute and mounting medium like DPX
etc.
4. Should be able
simultaneously.
to
handle
both
histology
and
cytology
sample
5. Should have an in-built filter to remove any vapors or fumes.
6. Easy to operate with different program setting and a touch screen panel.
7. Should be able to accept slides from different automated slide stains.
8. UPS for 1hours back up.
9. International CE certification for medical equipment.
Accessories –
1. Cover slips of different sizes & thickness – 500 each.
2. Dust cover.
3. Standard accessories with the main equipment.
6
Human Specification for human morbid tissue materials
morbid
tissue
materials
CardioVascular
Mitral stenosis
Atheroma aorta
Lt. ventricular hypertrophy
Fibrinous pericarditis
Dilated Cardiomyopathy
Infective endocarditis
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
2
each
- 107 -
500.00
Respiratory
GastroIntestinal
Renal
Vascular
Bone
Female Genital
Hepato-Biliary
Female Breast
Male Genital
Lymph Node
Lobar pneumonia
Bronchiectasis
Emphysema
Pulmonary Tuberculosis fibrocaseous & miliary
Bronchogenic carcinoma
Silicosis
Bysinosis
Peptic ulcer
Typhoid ulcer of S.I.
Granular contracted kidney
Large white kidney
Hydronephrosis
Renal cell carcinoma
Renal stone
Syphilitic Aortits
Osteomyelitis-sequestrum
TB spine
Osteogenic sarcoma
Giant cell tumor
Fibroid uterus
Carcinoma cervix
Micro-nodular cirrhosis
Fatty liver
Metastatic liver
HCC
Carcinoma breast
Carcinoma Penis
Seminoma of testis
Benign hyperplasia of Prostate
TB Lymph Node Hodgkins LN
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
2
each
500.00
2
each
2
each
100.00
2
each
2
each
50.00
200.00
2
each
2
each
100.00
2
each
2
each
50.00
2
each
- 108 -
200.00
200.00
100.00
50.00
DEPARTMENT. OF RADIOLOGY ESI-PGIMSR, JOKA
1
MULTISLICE CT
TECHNICAL SPECIFICATION FOR MULTISLICE CT SCANNER
SCANNER
Spiral CT Scanner system for high resolution whole body scanning. The instrument must be
capable of acquiring minimum 128 slices per 360 degree rotation.
TECHNICAL SPECIFICATION
1) SCAN TIME:
1. The scan time for one gantry rotation of complete 360 degree should be less than
equal to 0.40 secs.
2. Rotation time of Cardiac Applications should be less than equal to 0.35 secs.
2) GANTRY:
1. Aperture of 70 cm or more.
2. Tilt from console must be present.
3. Bidirectional inter-phone must be present.
4. Should have FOV of at least 50 cm or more.
5. Auto positioning LASER light with 1 mm positioning accuracy.
3) GENERATOR:
1. 70 KW or more.
2. Continuous X-Ray exposure.
3. High frequency X-Ray Generator.
4) X-RAY TUBE:
1. X-Ray tube voltage should be 80-135 KV or more.
2. X-Ray tube current should be 20-600 mA or more (preferable).
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 109 -
01 set
100000.00
3. Anode heat storage capacity should be 7.0 MHV or more.
4. Anode heat dissipation/cooling rate 1000 kHU/min.or more.
5) X-RAY DETECTOR:
1. Solid state /Ceramic detector type.
2. 128 slices per rotation.
3. 700 or more number of physical detectors per row.
4. 35 mm or higher coverage per rotation in Z-axis.
5. Detector element size minimum 65 mm or less.
6) PATIENT TABLE:
1. Remote control from Console.
2. Load Capacity of 200 kg or more.
3. Horizontal movement range 170 cm or more.
4. Motor driven couch top movement.
5. Scannable range 170 cm or more.
6. Couch top material Carbon fibre.
7) IMAGE QUALITY:
1. Spatial resolution at least 21 lb/cm at 0% MTF.
2. Low contrast resolution at least 4.0 mm at 0.3%.
8) ACQUISITION & PROCESSING WORKSTATION:
1. High performance computer for date acquisition, image reconstruction and routine
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 110 -
post processing.(2 in number 18 inches or more, high resolution LED monitor with
image area matrix dimention of 1024 X 1280).
2. Fast advance processor in the industry available.
3. RAM: 6 GB or more.
4. HDD: Should store at least 8, 00,000 images in compressed mode.
5. DVD/CD writer: CD (700 MB & DVD(4.7 GB)
6. DICOM Viewer- automatically included in every CD/DVD for Viewer’ PC
9) STANDARD SOFTWARE INCLUDING CONSOLE:
1. MPR
2. 3D SSD
3. VRT for advance 3D application.
4. MIP
5. CT Angio
6. Virtual endoscopy software for visualization of vessels and air filled structures.
7. Dose management to control and reduce dose.
8. Automated arrhythmia conversion software.
9. Vessel measurement.
10. Small volume quantification.
11. Injector synchronization system.
12. Brain and body perfusion analysis.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 111 -
13. ECG synchronization volume acquisition.
14. 3D cardiac scanning and reconstruction.
15. Axial/spiral perfusion for 80 mm or more.
16. Paediatric and infant based protocol shall be available based on infant weight.
10) SPECIAL PROCESSING SOFTWARE FOR WORK STATION:
1. Cerebral perfusion study with stroke protocol.
2. MIP, Volume MIP, MIP state viewer.
3. 3D SSD rendering software.
4. Curved MPR reconstruction.
5. CT Angio with quantitative vessel analysis.
6. Virtual analysis.
7. Brain & body perfusion software.
8. Autobone removal software.
9. Lung nodule assessment software.
10. Liver segmentation software.
11. Complete Cardiac package with ECG gated studies.
12. Calcium scoring and cardiac function analysis.
13. Cardiac post processing.
14. Quantification of stenosis and plaque analysis.
15. Automatic vessel measurement.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 112 -
16. Single click Coronary tree extraction.
17. One touch volume rendering of the whole heart.
18. Calcuim and Coronary Angio reporting.
19. ECG gated dose modulation.
11) REAL TIME CT FUROSCOPY:
12) ACCESSORIES:
1. Dual head cardiac injector with 500 sets of syringes and connecting tubes.
2. Dry laser camera with
1. Resolution: 16 bits /50 odpi or more with minimum three ports.
2. Support multiple film sizes one of which must be 14” X 17”.
3. Through put of 120 films or more per hour.
4. DICOM 3.0 compatible.
3. Lazer colour printer
1. DICOM 3.0 complaint.
2. Resolution at least 1200 X 1200 dpi.
3. Throughput minimum 30pages /min. (media types A-4, A-5, B-5 plain and bond
paper)
4. Two sets of patient positioning accessories.
5. ECG monitor on the gantry.
6. 3 numbers of Patient trollies.
7. True on line UPS with 60 minutes back up of appropriate KVA. The CT scanner
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 113 -
in addition should be supported by a separate suitable high capacity stabilizer
for the complete system as a standby protection in the event of failure of the
UPS.
8. The Biphasic defibrillator with adult and paediatric probes.
9. Pulse oxymeter with adult and paediatric probes.
10. 10. Crash cart for medicine.
11. Light weight 12 number of lead aprons.
12. 2 number of view box.
13) CIVIL WORK:
1. Turnkey work to be quantified for room size of
The Vendor may visit the installation site before bidding to access the turnkey cost.
2. Lead glass of appropriate size between the machine room and control room for
radiation protection.
3. 2 Ton Air-conditioner, 3 in number for CT room and One 2 Ton Air-conditioner for
control room and two 2 Ton Air-conditioner for Radiologist reporting from and
storage room.
4. Dehumidification-Appropriate dehumidifier for CT scanner room and control room.
14) QUALITY STANDARD:
Product quality certificate of appropriate authority must be submitted with the offer.
The system offered should carry a NOC from AERB for installation on India.
2
500 MA X-RAY
MACHINE
Technical specification of 500 MA X-RAY MACHINE
A 500 mA. Multipulse High frequency X-Ray machine for Radiography.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 114 -
01
set(against
condemnatio
n)
40000.00
RATINGS: 50KW High frequency X-Ray generator for radiography .
Radiography Parameters: 35 to 125KVor150 KV Multi steps as many as possible
Small Focus – 100 mA & 200 mA
Large focus – 300mA, 400mA and 500mA
mAs – 1.25 to 200 mAs in multiple steps as many as possible.
Control: Floor or Wall mountable control panel, ON and OFF switches
Automatic safety system to block unwanted exposure factors beyond tube ratings. Digital
display of active KVP, mA and mAs. Hand switch with flexible long retractable cord. Compact
durable soft touch keypad. Table or Vertical Bucky selection and table top radiography switch.
Ready and X-Ray on switch with indications.
Tube Unit: Rotating anode tube unit with dual focus x-ray tube insert.
Anode Speed:- Minimum 2800 rpm.
Focal spot:- Dual focus,
Small focus:- 0.6mm to 1 mm
Large focus:- 1.2mm to 2.00 mm
Protection:- Totally thermal Protection.
HV/HT cable compatible with X-ray tube.
Motorized tube movement with all round tube angulation preferable
Collimater: Manual light beam diaphragm.
Tube Stand: Floor to ceiling stand and with counter balanced tube head 360 degree
rotation (rotatable+/- 180 degree), tube rotation with column axis all round movement (
Longitudinal, Transversal, UP & Down), mounted on floor ceiling rails for convenient
movement. Safety lock in case of wire shortage.
Ceiling suspension tube preferable.
Table: Motorized table with 6 way movement (table height adjustment) .
Motorized bucky with grid ratio 8:1 (80 to 100 lines per inch). Stainless steel cassette tray with
electromagnetic brakes. Stain free laminated table top.
Operating Voltage: 400-440 volt AC 50 HZ. Three Phase.
Chest Stand: Motorized or manual Vertical Bucky Stand with counter balanced. Head to Toe
Vertical travel (455mm to 1900mm).
Electromagnetic locking method (lock released when switch is pressed).
Also separate Cassette holder attachment with the Vertical Bucky Stand for direct exposures.
Accessories:- Compression Band, Hand Grip & foot step.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 115 -
Unit should have the AERB approval.
DEPARTMENT OF PAEDIATRIC
1
NEONATAL
RESUSCITATION
UNIT WITH
WARMER
NEONATAL RESUSCITATION UNIT WITH WARMER:NEONATAL RESUSCITATION UNIT (MICRO-COMPUTER CONTROLLED)
WITH WARMER
SPECFICATION:a) Controlled Resuscitation system. Oxygen Administration facility, Low Pressure
suction and warming with infrared Radiant Heat Source.
b) Inline Manometer,
c) Oxygen Administration Facility: i) Oxygen Flow control facility with flow meter
(o to 15 lit/min).ii) Oxygen Pressure Adjustment valve, iii) Humidifier Bottle, iv)
Facility to keep Oxygen cylinder, v) Connecting hose for wall Outlet. vi) Silicon
Autocluvable Resuscitation Bag with 00 and 01 size of Masks.
d) Slow Suction: This is a specially designed electrically operated slow suction.
Apart from others, it is non-motorized slow suction. The suction pressure can
be adjusted as per requirement.(0-110 mm Hg.)
e) Servo Control System to maintain an optimum skin temperature.
f) Precise cradle Temperature control.
g) Manual Warming Facility.
h) Stop Watch- additional Facility provided to note down timings during
monitoring various vital signs of baby, e.g. temp. Heat rate, Respiration Rate.
i)Reminder Timer.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 116 -
02 pcs
(against
condemnati
on)
4000.00
j) Apgar Timer with Birth Time Recorder.
k) a) Power Source: 230 +/- 10% volts. 50 Hz.
B) Control Method: Micro-Computer Controlled intelligent proportionate
Power Control.
c) Heater Capacity: 600 Watts.
d) Light Source: 60 watts bulb to examine babies.
e) Power Consumption: 850 watts.
m) Temperature Controller Specifications:I. Skin Mode Control: From Body Temperature to 38 C.
II. Air Mode Control: From Room Temperature to 39 C.
III. Resolution: 0.1 C.
IV. Accuracy: +/- 0.2 C.
n) Alarms: (Audio visual with auto Reset facility)
Alarm Condition
Message on Display
Skin + I.C.
HI
Skin - I.C.
LO
Air +1.5 C
HI
Air - 3 C
LO
Skin >38C
OVER
Air<39C
Skin/Air Sensor Failure
Heating system Failure
OVER
Fail
HEAT OFF
o) Safety Cutoff;
When Skin Temperature exceeds 38C.
When Cradle Temperature exceeds 39C.
p) Power Failure Alarm: Audio –visual.
q) Distance between Heater source and Baby: 88 (34.5)
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 117 -
r)Dimensions: Height X Width x Depth-cm (inch)
203 (80) X 63.5(25) X 100 (39.5)
s) Baby Tray: Length 72 (28.3) x width 45 (17.7)
t) Should have 1 drawer system attached with the equipment for storage facility.
w) It should be in compliance with ISO 9001:2000. Should have Q.A. International
Certification Limited.
2
DOUBLE
SURFACE
LED
PHOTOTHERA
PY
DOUBLE SURFACE LED
Specification:Wide Effective Area.
PHOTOTHERAPY
Unit should have blue cool led light source with wave length of 450-460 nm.
Long Life->20,000 Hrs.
No UV / IR Radiation.
No Heat Generation.
Low Power consumption.
Negligible Maintenance Cost.
Light Weight & Compact.
Height and Angle Adjustment facility.
Mounted on Castor Wheels for Easy Mobility.
Can be used in Conjunction with any make radiant Warmer.
Digital time Totalizer.
Irradiance> 60 u/W/cm2/nm.at 45 cm from the light source.
Wavelength 450-460 nm (peak 455 nm free of UV and IR radiation.
Height adjustable from 1198+/-20 mm to 1680+/-20 mm
UNDER SURFACE SOURCE UNIT:
Unit should have blue cool led light source with wave length of 450-460 nm.
Free of UV/IR radiation.
Light intensity is variable from 7-60 um/nm/cm2.at a distance of 45 cm.
Infant care Trolley in Stainless Steel Specification: Mechanical Specification:-
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 118 -
02
pcs(against
condemnatio
n)
2000.00
Convenient working level with 6 mm thick imported acrylic collapsible side support, accessible
from all sides.
Acrylic Tray with Foam mattress. IV Pole & Facility to take X-ray.
Head up /down facility.
Stand with separate Infant care trolley.
Mounted on 4” castor wheels for easy mobility.
Infant care Trolley with transparent acrylic bed and bubbles mattress for baby. Fabrication in
mild steel, baby bed area in Stainless steel.
3
CPAP MACHINE
SPECIFCATION OF CPAP MACHINE
SYSTEM: Valve based continuous flow CPAP and IPPR.
Bubbler based bubble CPAP.
DISPLAYS: Digital and Analog Display of CPAP pressure in CPAP Mode.
Continuous Digital display of Delivered pressure in IPPR Mode.
ALARMS; CPAP High and low Alarms (Audio Visual)
02
pcs(against
condemnatio
n)
2000.00
PRESSURE GAUGE: -20 to 100 cm H2O
GAS MIXNG: Air-Oxygen Mixer using calibrated Rotameters.
AIR SOURCE: Inbuilt Air Compressor (Optional) (20 to 90 PSI).
O2 SOURCE: Inlet for Oxygen Gas (20 to 90 PSI).
POWER: 230V A.C. 50 Hz.
Asccessories: Warmidifier, Breathing Circuits(Disposable).
CPAP Interface, Nasal Prongs, Dummy Test Lung.
DEPT OF EYE ESI PGIMSR, JOKA KOLKATA
1
VISUAL
TECHNICAL SPECIFICATION FOR VISUAL FIELD RECORDING INSTRUMENT
( PERIMETER SYSTEM)
FIELD
Specification:
RECORDIN
G
Stimulus intensity
0.03 -10,000 Asb
INSTRUME Stimulus Duration
0.1 – 9.98 secs
NT
Stimulus Wavelength
Broadband visible light
Maximum Bowl illumination
31.5 ASB
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 119 -
01 pc
10000.00
GPA Software
Testing features:
Threshold Testing Library
Central Field Testing Patterns:
30-2, 24-2, 10-2 Macula
Peripheral Field Test Patterns:
60-4, Nasal Step
Screening Test Library
Central Field Patterns:
C-40, C-64, C-76, C-80, C-Armaly
Peripheral Field Test Patterns:
P-60, DD-81, FF-120, FF-135, FF-246, FF-Armaly, Nasal Step
Specialty Test Library
Esterman monocular
Esterman binocular
Superior 36
Superior 64
Stimulous / background color
White on white
User defined test storage
User features:
Fixation Monitoring
Heiji Krakau blind spot monitor
Video eye monitor
Trial lens Holder
Remote video eye monitoring capability
Operator interface
Help Menu
Touch screen on CRT
Motorized chin rest
Printer
Printex Thermal printer, table mounted
Patient data input
Name, Birth Date, ID, Trial Lens, VA, Pupil size
IOP, C/D ratio, Diagnosis Code, Procedure Code, Comments
Department of Biochemistry
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 120 -
1
SEMI
AUTOMATE
D
BIOCHEMIS
TRY
ANALYZER
SPECIFICATION FOR SEMI AUTOMATED BIOCHEMISTRY ANALYZER.
I. Item :
Semi Automated Biochemistry Analyzer with UPS 0.5 KVA.
II. Analysis Option:
a. Absorbance
b. 1 point end linear & non linear.
c. 2 point end linear & non linear.
d. Rate linear & non linear.
e. Immunoturbidimetry.
OPTICAL SYSTEM
III. Light Sources:
Pre aligned Quartz halogen lamp.
IV. Wave Length:
Automatically Selectable narrow band interference quartz filter
within wavelength of 340 -700 nm -- fixed seven or eight filters
and two optional filters as per users choice.
V. Measurement Time :
Selectable.
CUVETTE SYSTEM
Cuvette :
VII. Cuvette Temperature:
VIII. Aspiration System:
IX. Aspiration Volume:
X. Cuvette Blanking:
FUNCTIONS
a. Flow cell Cuvette.
b. External rectangular Cuvette.
Peltier control & programmable at 25˚C, 30˚C and 37˚C.
Motor driven pump.
Programmable.
Automatic.
XIII. Programmable Parameter: About 100 user defined test programs including routine biochemical
parameters, enzymes, immunological markers, truly open system,
selection through key- board.
XIV. Calibration:
Automatic against standard / calibration.
XV. Quality control:
a. 2 levels of control (at least)
b. Levey - Jennings diagram.
c. Manual entry of QC result.
XVI. Memory Storage:
a. Minimum 200 patients result.
b. Calibration result.
c. Quality control result for 01 month.
OPERATOR INTERFACE
XVII. Display:
a. Graphic LCD.
b. Display of reaction curve, absorbance, temperature.
c. Display of result of real time.
d. Graphical display of reaction time.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 121 -
01 pc
6000.00
e. Calibration curve graphical display.
XVIII. Key board:
XIX. Printer:
a. Chemical and moisture prevented single touch alphanumeric
membrane key panel.
a. Built in thermal printer with full graphic facility.
b. Parallel full page ink printer with formatting options.
SOFTWARE
XX. Reporting format:
a. Conventional
b.SI unit(Optional/Interconvertible).
XXI. Recalculation :
Recalculation of result following modification of calibration,
measurement timings and wavelength.
XXII. Automatic Flagging:
a. Absorbance and linearity cheek.
b. Reagent stability.
c. Substrate depletion.
XXIII. Peripheral interfacing: a. Parallel ports for external printer , key- board and PC. Software PC
Compatible.
ADDITIONAL
XXV .Power Cord :
XXVI: Dust Cover :
XXVII: Working Manual :
2
HbA1c
analyzer
Indian Type 3-pin power cord locally available and replaceable .
Washable dust-covers for main unit and key-board, etc.
Working Manual by manufacturer in original
Specification for HbA1c analyzer
Analytes
HbA1c and detect abnormal haemoglobins
Principle
HPLC Technology
Sample Volume
Less than or equal to 3ml.
Sample loading
Should load about 10samplesper lot with continuous loading facility
CV%
<3%
Throughput
< 8 minutes per sample
Assay time
2-3 minutes for HbA1c
Assay
Should be able to detect correct A1c values in the presence of commonly
occurring abnormal haemoglobin variants.
Primary tube sampling Facility should be there
Controls
Company should provide external and internal normal and abnormal control.
Calibrators
In- kit external calibrators
Program mode
Dual program mode to perform either HbA1c or HbA2/HbF/HbA1c without
changing reagents or columns
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 122 -
01 pc
2000.00
Check facility
Certification
method.
Approvals
Installations
3
Fully
Automated
Electrolyte
Analyzer
Should be able to check all system parameters (cartridge, reagent, waste etc)
System should be NGSP/DCCT certified and traceable to IFCC reference
Both CE and FDA approvals
Must have > 500 installations across major cities all over the country
01 pc
Fully Automated Electrolyte Analyzer with all the necessary accessories having
following features, with UPS 0.5 KVA
Measured Parameter
Sodium
Potassium
Chloride
Features
Sample volume 75 -125 µl
Analysis Time within 90 second
Sample throughput 40 – 50/ hour
Sample Type –Whole Blood , serum, Plasma , urine , and QC.
Fully Automated calibration of all parameters .
Individual switch off / on facility of the parameters preferable.
Data display on built in LCD display screen.
Data print out on fast flow thermal printer.
Memory for QC result , Patient samples and error reports.
Built in programmable stand –by mode facility for economical operation
Flagging of abnormal results and user programmable ranges..
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 123 -
2000.00
Interface – RS 232.
Operational Manual.
Built in voltage stabilizer for the voltage range from 100 – 240 VAC/ 50 HZ
Consumable Kit
Reference electrode
01 No
Reference Housing
01 No.
Sodium electrode
01 No
Potassium electrode
01 No.
Reagent, Conditioner and cleaning solution 01 Pack each as starter
 Warranty
 Installation & Local Training
12 Months from the date of Installation.
Free of Charge at site
I. Item :
Fully Automated Microprocessor Controlled ISE Electrolyte
Analyzer with built-in voltage stabilizer for voltage range 100240VAC/50Hz and on-line UPS 0.5 KVA.
II. Measured Parameters:
a. Sodium
b. Potassium
c. Chloride
All the parameters to be analyzed from samples of whole blood, plasma,
serum, urine and body fluids.
III. Measuring System:
Ion Selective Electrodes, for individual analytes, individually replaceable
and/ or reference electrode. Individual switch-on/off facility of the
parameters is preferred.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 124 -
IV. Measurement Time :
V. Operating Temperature:
VI. Aspiration System:
Maximum 90 seconds.
Peltier control at 37˚C, workable at ambient room temperature.
Automated prompt-guided sipping of sample. Motor driven peristaltic
Pump. Automated sample probe cleaning.
VII. Aspiration Volume:
VIII. Disposal of Waste:
75 – 125 µl.
Closed system of sample waste disposal.
FUNCTIONS
IX. Throughput:
X. Calibration:
XI. Quality control:
XII. Memory Storage:
40 to 50 samples per hour.
Automatic calibration of all parameters.
External Standard / Quality Control
a. Patients result.
b. Calibration result.
c. Quality control result for 01 month.
d. Error reports.
OPERATOR INTERFACE
XIII. Display:
a. Built-in LCD backlit display.
b. Display of alphanumeric characters.
c. Display of result in real time.
d. Built-in programmable stand-by mode facility.
XIV. Key panel:
Chemical and moisture prevented single touch
membrane key panel.
XV. Printer:
a. Built in fast flow thermal printer with full graphic facility.
b. Parallel full page laser printer with formatting options.
SOFTWARE
XVI. Reporting format:
XVII. Automatic Flagging:
a. Factory set, individual parameter-wise in built-in printer.
a. Out-of-range results.
b. User programmable reference ranges of all individual parameters.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 125 -
CONNECTIVITY
XVIII. Peripheral interfacing:
RS-232 Parallel ports for external printer and PC.
ADDITIONAL / CONSUMABLES TO BE SUPPLIED ALONGWITH THE MAIN EQUIPMENT
1. One set of Start-up Reagent Pack, , Electrode Cleaning Solution, Deproteinizer,
Multilevel control
2. Operating Manual in original manufacturer’s version: one number
3. UPS on-line, capacity 0.5 KVA: one number.
4. Power cord Indian type: one number.
5. Washable eco-friendly dust cover: one number.
DEPARTMENT OF ANATOMY
1
CADAVER
CADAVER STORAGE TANKS (Full SS)
STORAGE
(Accommodate full human cadavers- at least 2 in each tank)
TANKS
Specification
(Full SS)
1. OVER ALL SIZE: 72” (L) x 60” (W) x 24” (H) WITH CASTER
2. FOUR SIDES ENCLOSED BY 1.6 MM SS SHEET
3. BOTTOM SHELVES MADE OF 1.6 MM SS SHEET
4. BOTTOM STRUCTURE MADE OF 40 X 40 X 6 MM ANGLE FRAME
5. LIDS MADE OF 1.2 MM SS SHEET (DOUBLE SHEET MOULDED) WITH ONE HAVING
HANDLE-6.
6. INSIDE ONE HAVING BOWL FOR DRAINAGE WATER. WHEN GET THE SOLUTION
7. RAISED INSIDE THE CABINET THEN CLOSED THE ADJUSTABLE KNOB.
8. MOUNTED ON 200 MM CASTER (HEAVY DUTY)
9. EVERY JOIN WITH ARGON WELDING.
10. FINISH WITH GLOSSY POLISH.
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 126 -
06
pcs
15000.00
DEPARTMENT OF PHARMACOLOGY
1
Automatic electric recording drums
2
Cannula-made of corning glass (Arterial- hollow bulb with three arms, Venous–hollow glass tube- 4-5cm
length & 3-4 mm diameter Syms cannula)
3
Four Unit isolated organ bath palmer F.67
For Internal Organs with stirring arrangements, made of transparent acrylic sheet, chemically welded to
make leak proof. Complete with uprights, organ & oxygen tubes, capillary tubing, and frontal lever
etc.Temperature by immersion heater and control by thermostat.
4
Dissection instruments and injection syringes as required
Sets containing surgical standard scissors-2, curved scissors-2, pointed scissors-2, artery forceps-2,
Mosquito artery forceps-2, scalpel handle-2, plain forceps-2, toothed forceps-2, small retractors-2, etc.
Probes-2, hooks-2. To be supplied with proper cover and box.
5
X-blocks as required(Open and Closed) Machined from solid Brass rod, richly chromium plated to
hold 9mm, 6mm and 12.5 mm rods
6
Hook grip rods as required- Should be suitable to fit in an X-block
1
10
each
1
500.00
500.00
1
500.00
10
each
25
500.00
500.00
500.00
7
Plain stand
25
500.00
8
1
500.00
9
Jackson’s Enterograph - a) hollow metallic tube about 15 cm in length and 15 cm in diameter.
b) hook welded at its lower end
c) a pulley fixed at the lower end
Hair Aesthesiometer-Palmer W.290
1
500.00
10
Manometers mercury Palmer C-200
3
500.00
11
Copper Trays (10”x8”x1”)
25
500.00
12
Microscopes ordinary - With fixed bright filed two lens condenser and iris diaphragm, heavy metal stand
with triple nose piece. Coarse adjustment by rack and pinion and fine
adjustment by precision grade slow motion arrangement in a beautiful storing cabinet Total magnification 675 x
Eye pieces H10x, H15x
Objectives 10x, 45x (spring loaded)
Chemical Balance – Sensitive
Balance beam scale, capacity: 120g/0.01g 220g/0.01g 320g/0.01g 1200g/0.01g 2200g/0.01g 3200g/0.01g.
Power AC/DC with lithium battery. Display: LCD/LED with back light. Fan size: diameter 130mm.
Operating lamps- Standard quality
2
500.00
1
500.00
1
500.00
13
14
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 127 -
15
Skin and Rectal Thermometer Barun -
1
500.00
16
2
500.00
17
Starling's or Heart Lever:-This lever is used to record the contraction of heart. The differences between this
& other isotonic levers is that fulcrum lies at one end beyond the point of attachment. It consist of a frame
carrying a light lever arm with holes and notches supported by a fine adjustable nickel silver spring
attached to an adjustable hook.
Microscope with mechanical Stage and oil immersion
2
500.00
18
B.P. Apparatus Mercury. sphygmomanometer, Desk el
2
500.00
19
Stethoscope - Traditional
2
500.00
20
2
500.00
2
500.00
2
500.00
2
500.00
2
500.00
25
Gimbal lever - obviates extremely careful
adjustments as the writing lever always falls towards the
paper
Simple lever stout construction duly chromium plated
frame with stop at one end interchangeable 1/4" stem
the lever fits thorough axle pivoted between centers and
a thumb screw on the axle permits the lever to be adjusted for length
Brodies’ Universal lever- the axie is screwed has two nuts
between which interchangeable levers are centered while
screwing up the central screw the stem screws into the
head with various positions with adjustable spring
support one plain lever one notched lever with holds and one shorts lever.
Frontal writing lever - This lever is designed in such a way that the writing point rotates freely about its
axle. This helps in reducing the tension between the smoked paper and the recording tip. The contraction
are recorded as straight line
Fixit lever - the levers can be fixed to the spindle in the
center p f which a vulcanite spindle on one of these pins
lever fits, sliding through the frame is a rod carrying a
spring that can be caused to bear against the roller its
turning while other adjustment are made.
Water bath 4 hole electrically heated
1
500.00
26
Standard power tables
1
500.00
27
Colorimeters
1
500.00
28
Cautery machine, electric Blendsone
1
500.00
21
22
23
24
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 128 -
29
Condon’s Drop Recorder-Palmer B-75
1
500.00
30
Jacquets graphic chronometer
1
500.00
31
Long Extension for paper palmer A-130
1
500.00
32
Metronome Palmer B-5.
1
500.00
33
1
500.00
34
Chemical Balance-ordinary Apothecary’s
Best quality with divided doors show case, capacity 250gms. Sensivity 1-2mgm having all stone agates
fitted in open graduated beam
Pneumograph Palmer E
1
500.00
35
Museum drugs specimen boxes rectangular, acrylic with cover. Sizes:- 9”x5”x4”(inch)& 6”x4”x3”(inch)
500.00
36
Microscope lamps - standard quality
50
each
2
37
Multimeter
1
500.00
38
Temperature controlled water bath 37 O C.
1
500.00
39
Cycle ergometer
1
500.00
40
1
500.00
41
Operating Table- JKA-172 : Suitable for Rabbits, Rats, Guinea Pigs and such like small
animals. Top is of Stainless Steel and provided with adjustable head
holder, tie-cleats, cut-back at the head-end with warming chambers.
Instrument Trolley (30”X18”X30”)
1
500.00
42
Instrument Trolley( 48”X24”X30”)
1
500.00
43
Weighing machine upto 150kg
1
500.00
44
Manometer mercury glass U-tube (5 mm bore , two vertical limbs 30 mm height half filled with mercury
(upto 250 mm of Hg)
Tracheal cannula metal
( z-shaped & y- shaped)
Bull dog clip
2
500.00
2
each
10
500.00
2
500.00
45
46
47
Rat holder- single u and ring pattern
38 mm with Universal joint
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 129 -
500.00
500.00
2
500.00
49
Mercury manometer –Meriam, All Manometers are fabricated from true-bore Borosilicate glass, floats are
perfectly, lapped to eliminate leakage and are fitted with feather weight stainless steel capillary. Standard
Mercury Mercury Manometers: Without stopcock, with adjustable scale.
Autoclave electric-small
1
500.00
50
Deionizer-small
1
500.00
51
Sterilizer electric size 12”x8”x6”
1
500.00
52
Stimulator electronic Arthus Thomas- Selectable pulse per second in different steps and pulse with,
continuous variable volt in multiple of 1 and 10 with internal, external and single pulse mode
Flame Photometer
1
500.00
1
500.00
48
53
DEPARTMENT OF ANESTHESIOLOGY (MANICKTALA)
1
01 pc
Monitor for A. Monitor for Continuous Measurement of Cardiac Function:
Continuous
Measuremen
1. It should be arterial line based continuous monitoring device for Cardiac output,
t of Cardiac
Cardiac Index, Systemic Vascular Resistance and Stroke Volume.
Function
2. It must be supplied with good quality display device and ten Flotrac and necessary
catheter system.
14000.00
3. The device should be compatible with Flotrac sensor system
4. Necessary accessories should be supplied for systemic vascular resistance
measurement
5. It must be CE and/or FDA certified
2
Monitor for
continuous
measuremen
t of body
tissue
oxygenation
and oxygen
delivery
status
B. Monitor for continuous measurement of body tissue oxygenation and oxygen 01 pc
delivery status:
1. It should be auto-calibration based arterial-venous line based measuring device to
provide continuous measurement of ScVO2, SvO2 , Extra vascular Lung water
index and Ejection fraction as well as End Diastolic volume of heart
2. The monitor should be supplied with 10 (ten) relevant and related sensors for
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 130 -
8000.00
measurement of hemodynamic variables
3. Suitable display and storage device for data should be supplied
4. It should be CE and/or FDA certified
3
Brain
Function
Monitor for
depth of
anesthesia
01 pc
C. Brain Function Monitor for depth of anesthesia:
1. It should be Density Spectral Array (DSA) based and Bi-hemispheric EEG power
dependent monitoring device to provide easy-to-interpret status of depth of
anesthesia.
2. It should also be able to provide measurements of SpO2, EtCO2, continuous
hemoglobin, Perfusion Index & Pressure Volume Index.
3. Waveform and/or Digital system of display as appropriate
12000.00
4. Device should be FDA and/or CE certified
4
Instant
Hand held
blood pH
and Lactate
monitor
01 pc
D. Instant Hand held blood pH and Lactate monitor:
1. Portable, cartridge based hand held device capable of measuring blood pH,
Lactate and other variables such as Troponin, Ionised Calcium, Prothrombine
Time, Creatinine Kinase-MB and Brain Natriuretic Peptide
6000.00
2. Measurements should be quantitative in nature
3. It should be supplied with wireless based printer and electronic simulator for
calibration
4. It must be FDA and/or CE certified
5
Lumber
Puncture
Simulator
with
Epidural
block
trainer
01 pc
E. Lumber Puncture Simulator with Epidural block trainer:
1. The device should be a 3D image guided one suitable for training of epidural
needle insertion
2. It should be based on real time motion picture based capturing system with
display of procedure on screen
3. The system should be capable of evaluation of trainee’s performance
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 131 -
16000.00
4. All relevant interfaces and accessories should be supplied with the simulator
5. It must be FDA and/or CE certified
6
Spinal
Injection
Trainer
01 pc
2000.00
01 pc
G. Central Venous Catheter Simulator:
1. Simulator should have life like anatomical structures for identification of parts
related to central venous catheter insertion
8000.00
F. Spinal Injection Trainer:
1. Mounted trainer should be able to be used multiple times
2. It should be supplied with three sets of accessories like fluid bags and simulators
3. One vertebrae must be visible for proper identification of performance site
4. Trainee should be able to be guided by perceptible tissue resistance while going
through different levels of tissues
5. It should be CE and/or FDA certified
7
Central
Venous
Catheter
Simulator
2. It should allow trochar and guide wire insertion for complete training
3. Device should be supplied with five replaceable skin pads for each site of training
4. It should be supplied with all accessories like artificial blood (two units), fluids,
spare vessels (two numbers), battery and other relevant items
5. Facility to check correct position of catheter placement should be there
6. It should be CE and/or FDA certified
8
Cricotrache
otomy
trainer
H. Cricotracheotomy trainer:
1. It should be able to train routine as well as percutaneous tracheotomy procedure
2. It should have easily palpable anatomical land marks for identification of
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 132 -
01pc
2000.00
structures
3. Trainer must be steady in nature and should be supplied with five sets of spare
skin for cricotracheotomy
4. It should be CE and/or FDA certified
9
Peripheral
Nerve
Stimulator/
Locator
03 pcs
I. Peripheral Nerve Stimulator/ Locator:
1. The device should be able to locate nerves percutaneously through electrical
stimulation based technique
5000.00
2. It should be able to be used with monopolar as well as bipolar based stimulation
technology
3. Current intensity preferably be between 0 to 60 mA and stimulating impulse upto
1ms
4. Should be able to measure and display actual current passing through tissues
5. It must be supplied with insulated cannula , ten in number each for size 22, 24 &
25 G as well as re-chargble battery and charger.
6. Needle quality should be able to give best image under ultrasound guided
procedures
7. It should be FDA and/or CE certified
10
Multifrequency
based deep
heat
generator
01 pc
J. Multi-frequency based deep heat generator:
1. Equipment should be multi-frequency based dual outlet heat generator using
long waves with a emission frequency range between 450 to 500 KHz
2. It must have coupling system of capacitive and resistive therapy system for
heat generation at different depth of application area
3. Electrode pairs and handle tips with various diameters such as 30,50 and 70
mm must be supplied with the equipment
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 133 -
16000.00
4. Power must be 100 W/KOhm or more
5. It should be CE and / or FDA certified
11
Airway
management
Trainer:
01 pc
K. Airway management Trainer:
1. Trainer must have good quality land marks of upper airway and pulmonary
structures for proper identification during intubation training.
2000.00
2. It should allow various techniques of intubations and different methods of
airway related activities like application of suction, Sellick’s maneuver,
observation of pupil and carotid pulse palpation
3. It should be supplied with two sets of artificial lungs
4. It should be FDA and/or CE certified
12
Handheld
instant
hemoglobino
meter with
facility to
measure
Methaemogl
obin
01 pc
L. Handheld instant hemoglobinometer with facility to measure Methaemoglobin:
1. It should be able to be applied to patients of all age groups and necessary
probes/accessories to be supplied in two in numbers for each age group
2. It should work even in low perfusion status and should be least interfered by
electrical disturbances
3. It should be able to provide pulse variability index, blood hemoglobin and
methemoglobin level non-invasively on continuous as well as point of care basis
4. Perfusion index should be between o.o2 to 20%
5. Waveforms and/or digital display mode of presentation
6. It should be FDA and/or CE certified
G:\Equipments - Two Bid System(Open tender)MEDICAL COLLEGE 2013-Phase II Terms & Conditions, Equipment & Instruments 03.11.2014 ).doc
- 134 -
4000.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising