Master Cm 7000PAL DVR Qsg Web

Master Cm 7000PAL DVR Qsg Web
Troubleshooting
Digital Video Recorder (DVR) Functions
Get to recorded
programs
Freeze/Pause
Skip back
10 seconds
Signal
Issues
Fast forward
at 4 different
speeds
Stop playback
or recording
Starts
playback
Check the signal strength on your channels. Using the remote control, press
MENU, select Setup, System Setup, Channel Setup, then Add a New Channel.
Find the channel in question and verify that it has a strong signal. Channels
showing signal strength below 60 may experience signal loss.
Missing
Channel
Record a program
Highlight
Stop Playback
or a future program in the Guide,
press the SELECT button, and choose
Recording
Program Guide
your recording options from the
on-screen menu or press the
RECORD button.
Press SEARCH and follow the on-screen
instructions to locate a program you want
to record, then choose your settings.
Search Menu
Note: The Channel Master CM-7000PAL DVR
still records your programs when the receiver is
tuned off.
Remote
Control
Issues
Visit www.antennaweb.org to find out which channels in your area are
broadcasting in digital or analog.
Press the
button; it should illuminate. For another device that isn’t
responding, press that device’s MODE button (for example, press TV to
control a TV).
Replace batteries with four new alkaline AAA batteries. Be sure the batteries
are installed as indicated on the diagram inside the battery compartment.
To program your remote control for another device, refer to the User Guide.
DVR
Issues
Verify event timers are set as DVR timers, not as Auto-Tune timers.
If you run out of space on the DVR, unprotected events are erased, starting
with the oldest. Protect those you want to keep.
For Additional Information
Device Codes
TV: ____ ____ ____ ____
See the User Guide for a list of device codes.
VCR/DVD: ____ ____ ____ ____
AUX: ____ ____ ____ ____
CM-7000PAL DVR
Digital Video Recorder (DVR)
& HDTV Over-the-Air Receiver
The Channel Master CM-7000PAL DVR is only able to tune to digital channels
and therefore will not tune to a channel that is still broadcasting in analog.
To tune to an analog channel using your analog TV, press the ANALOG
PASS-THRU button on the remote control, then tune to the channel using
your TV’s remote control.
Skip Back 10 Seconds
Reverse at 4 Different
Quick Ways toSpeeds
Set a DVR Timer
Verify your antenna has not been moved out of proper alignment. This can
cause signal loss on some or all channels.
Reset the receiver by first powering it off, then unplugging it from the outlet
for 15 seconds, and plugging it back in. Power the receiver back on.
Skip forward
30 seconds
Reverse at 4
different speeds
Verify the coax cable to the over-the-air antenna IN port is hand-tight and
connected to your over-the-air antenna.
www.channelmaster.com
1.877.746.7261
User Guide
CM.PUB.CM7000PALDVR.QSG.200912
178232
quick start
guide
Connection & Set-Up
Features of Your Remote Control
To use most of the features listed here, make sure you are in Receiver mode
by pressing the
button
1
Channel Master antenna
not included.
Visit
www.channelmaster.com.
CM-2016
Outdoor Antenna
Easy Ways to Find a Program
Select a
program from
the Program
Guide.
Channel
Up/Down one
program at a
time.
Find and play
a recorded
program.
2
Enter a channel number.
Quick Tips and Shortcuts
3
To record a program that is currently playing, press the
RECORD button and follow the on-screen instructions.
Press the DVR button twice to quickly access your
recorded programs.
To skip ahead 24 hours in the Program Guide, press the
SKIP FWD button. To back up 24 hours, press the SKIP
BACK button.
See the User Guide for installation instructions.
To quickly set an event timer, press the RECORD button
from either the Program Guide or the Browse Banner.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement