Garmin | Nexus | Owner's Manual | Speed 2131-1 - Chicago Marine Electronics

Speed 2131-1 - Chicago Marine Electronics
Speed
- Instrument -
Installation and Operation Manual
English
English
SPEED
1
SPEED
This manual is written for NX2 Speed instrument version 3.10 – 5.00
Edition: March 2007
2
SPEED
1
2
3
Part specification .......................................................................5
Installation ..................................................................................8
Installing the instrument............................................................9
3.1
Mount the transducer ................................................................................... 10
3.1.1
Correct location of paddlewheel transducer............................................. 10
3.1.2
Installing the through hull fitting ............................................................... 11
3.1.3
Run and install the cables........................................................................ 12
3.1.4
Installing instrument to the Server ........................................................... 13
3.1.5
Installing the transducer direct to the instrument. .................................... 13
3.1.6
Installing transducer to the Server ........................................................... 14
4
First start...................................................................................15
4.1
4.2
5
Initialising the instrument ............................................................................. 15
Re-initialising the instrument........................................................................ 15
Operation ..................................................................................17
5.1
About this manual ........................................................................................ 17
5.2
How to use the push-buttons ....................................................................... 18
5.2.1
PAGE ...................................................................................................... 18
5.2.2
MINUS ..................................................................................................... 18
5.2.3
PLUS ....................................................................................................... 18
5.2.4
SET ......................................................................................................... 18
5.2.5
Clear / cancel / reset................................................................................ 19
5.2.6
Calibration ............................................................................................... 19
5.2.7
Lighting .................................................................................................... 19
6
SPEED functions ......................................................................20
6.1
SPEED main-function .................................................................................. 20
6.2
SPEED sub-functions .................................................................................. 20
6.2.1
TRIP LOG (TRP) ..................................................................................... 20
6.2.2
TOTAL LOG (LOG) ................................................................................. 20
6.2.3
MAXIMUM SPEED (MAX) ....................................................................... 20
6.2.4
START TIMER (STA) .............................................................................. 20
6.2.5
TIMER ..................................................................................................... 20
6.2.6
AVERAGE SPEED (AVS)........................................................................ 20
6.2.7
DISTANCE (DST).................................................................................... 20
6.2.8
DEPTH (unit/DPT) Only in Nexus Network .............................................. 21
7
Calibration.................................................................................22
7.1
Calibration of speed C10 ............................................................................ 23
7.1.1
C10 Return (RET).................................................................................... 23
7.1.2
C11 (Unit KTS) ........................................................................................ 23
7.1.3
C12 (1.25 CAL)........................................................................................ 23
7.1.4
C13 DAMPING (SEA).............................................................................. 23
7.2
C20, calibration of depth .............................................................................. 24
7.2.1
C20 (RET) ............................................................................................... 24
7.2.2
C21 (Unit m) ............................................................................................ 24
7.2.3
C22 ( - 00.0 ADJ)..................................................................................... 24
7.2.4
C23 (Unit°C) ............................................................................................ 24
7.2.5
C24 (0°C TMP) ........................................................................................ 24
3
SPEED
8
Maintenance and fault finding ................................................ 25
8.1
Maintenance.................................................................................................25
8.2
Fault finding..................................................................................................25
8.2.1
General ....................................................................................................25
8.2.2
Fault - action ............................................................................................26
9
Specifications .......................................................................... 26
9.1
9.2
10
Technical specifications ...............................................................................26
Optional Accessories ...................................................................................27
Warranty ................................................................................... 29
4
SPEED
1
Part specification
Items delivered with the instrument
Qty.
Description
1
1
1
1
1
2
2
1
1
2
1
5
5
1
1
Reference
Instrument, NX2 Speed Instrument
Instrument front cover
Drill template
Installation and user manual
Warranty card
Pin bolts for instrument mounting
Nuts for instrument mounting
Tube of silicon grease
Connection cover
4-pol screw terminal
Power cable, red and black, 3 m (9 ft)
Extra wire protectors, 0,25 mm (1/100”)
Extra wire protectors, 0,75 mm (1/32”)
Log transducer
Through hull fitting and dummy plug
1
2
3
4
5
6
6
6
6
6
7
8
8
9
10
Registering this product
Once you have checked that you have all the listed parts, please take time to fill in the
warranty document and return it to your national distributor.
By returning the warranty card, it will assist your distributor to give you prompt and
expert attention. Keep your proof of purchase. Also, your details are added to our
customer database so that you automatically receive new product catalogues when
they are released.
Warranty conditions see chapter 10.
5
SPEED
6
SPEED
Welcome aboard the Nexus Network!
Thank you for choosing NX2 and welcome to the world of the Nexus Network.
Through this manual we would like to help you install, operate and understand your
new Nexus Network.
The NX2 speed log may be used stand alone where the log transducer is
connected direct to the Speed Instrument or in a Nexus Network where the log
transducer is connected to the Server and the Speed instrument work as a
repeater.
The Speed instrument will automatically sense if it is stand alone or
in a Nexus Network.
The Server is the ”heart” of your Nexus Network, to which transducers for speed,
depth, heading, wind and navigation (GPS, Loran or Decca) are connected.
From the Server the single Nexus Network cable transmits power and data to the
instruments, which repeat the information sent from the Server, or other NX2
transducers.
The Nexus Network is designed with the industry standard RS 485 databus, which
allows you to connect up to 32 NX2 instrument units on the single Nexus Network
cable, thereby allowing you the flexibility to easily develop your system. The Nexus
Network is capable of carrying data 10 times faster than NMEA 0183.
The connection system, with a single 5 mm (1/5") cable and 4-pole jack plugs with
cable protectors, makes the installation easy. No need to drill big holes and the
cable can be cut to exact lengths. The connections at the Server are colour coded
and marked with a number for easy reference.
The instruments large display gives you very good viewing possibilities from any
angle, even in bright sunlight. The display and the five push-buttons have red back
lighting which you can set to three different lighting levels.
These NX2 instruments carry a two year warranty, which gives you as our
customer, confidence to trust NX2 and our commitment to quality.
To get the most out of your new NX2 product, please read through this manual
carefully before you start your installation.
Again, thank you for choosing NX2. If you see us at a show, stop by and say hello.
Good luck and happy boating!
7
SPEED
2
•
1.
2.
3.
4.
5.
6.
Installation
The installation includes 6 major steps:
Read the installation and operation manual.
Plan where to install the transducers and instruments.
Run the cables.
Install the transducers and instruments.
Take a break and admire your installation.
Learn the functions and calibrate your system.
Before you begin drilling ... think about how you can make the installation as neat
and simple as your boat will allow. Plan where to position the transducers, Server
and instruments. Think about leaving space for additional instruments in the future.
•
−
−
−
−
−
A few ”do nots” you should consider:
Do not cut the cables too short. Allow extra cable length at the Server so it
can be disconnected for inspection without having to disconnect all
attached cables.
Do not place sealant behind the display. The instrument gasket eliminates
the need for sealant.
Do not run cables in the bilge, where water can appear.
Do not run cables close to fluorescent light sources, engine or radio
transmitting equipment to avoid electrical disturbances.
Do not rush, take your time. A neat installation is easy to do.
•
The following material is needed:
Wire cutters and strippers.
Hole saw for the instrument clearance hole 63 mm (2½").
Hole saw for the Through hull fitting hole 43 mm (1 11/16").
5 mm (1/4") drill for the mounting holes.
Plastic cable ties
If you are doubtful about the installation, obtain the services of an experienced
technician.
8
SPEED
3
Installing the instrument
•
Place the adhesive drill template on the desired location for the instrument. Drill the
2 holes using a 5 mm (1/4") drill for the two pin bolts. Use a 63 mm (2½") hole saw to
machine the clearance hole for the instrument connection socket. Remove the
template.
•
•
•
Screw the two pinbolts to the instrument
Put the instrument in place
Screw the two nuts from the back
Note! The two nuts must just be tighten by hand
9
SPEED
3.1
Mount the transducer
3.1.1
Correct location of paddlewheel transducer
Generally the transducer should be placed as far
forward as possible along the waterline length and
close to the centreline.
It is important that the transducer is always in
the water, within the whole speed range of the
boat. Please note that the actual waterline length
of fast power boats shortens considerably at high
speeds. Therefore the transducer should be
placed at 25-35% along the true waterline from
the bow, when at full speed
Example:
Sailboats with a fin keel must have the transducer located at least 25 cm but not more than 75 cm
in front of the keel. It should be placed no more than 10 cm off the centreline.
On sailboats with a pronounced “V” in the hull, such as full-keel yachts, it might be favourable to
angle the transducer slightly so that it aims at the bow, rather than directly parallel to the
centreline.
This will help balanced the passing water flow measurement from one tack to another.
Avoid placing the transducer near the edge of
sharp hull chines. Transverse water flow in
these areas can affect the accuracy of
measurements.
10
SPEED
If you have a questions about the location of the through-hull, contact your builder, yacht
dealer, or other owners of similar boats for advice. Always remember to allow for
accessibility from the inside of the yacht when determining the final location.
3.1.2
1.
2.
3.
4.
5.
6.
7.
8.
Installing the through hull fitting
Use a 43 mm (1 11/16”) hole cutter to cut through the hull. (See above for correct location).
Slide both rubber O-rings on the dummy plug.
Generously apply the silicone grease to the exterior of the dummy plug.
Install the dummy plug in the through-hull fitting. Use a slow twisting motion and be sure that
is properly seated into the fitting.
With the dummy plug properly installed in the through –hull fitting, mount the fitting so that the
handle is exactly at right angles (90º) to the boats centreline. (For pronounced V-hulls see
section 3.1).
Apply the polyurethane sealing compound on the outer flange of the through-hull fitting and
tighten the nut on the inside by hand.
When this outer sealant has cured, remove the nut and apply sealant on the inside. Tighten
the nut again by hand.
Install the wire locking device onto the dummy plug /paddlewheel transducer.
11
SPEED
3.1.3
•
•
•
Run and install the cables
Run the Transducer cable from the transducer
or from the Server to the instrument.
If you want to cut the Nexus Network cable to
length, disconnect 4-pole jack plug and cut
the cable. Peel off about 35 mm (1,4") of the
cable insulation. Remove about 6 mm (1/4")
from the 3 isolated wires (the 4th wire is an
earth / screen). Attach the 4 cable protectors
to the wires using a pair of flat pliers.
Connect the 4 cable protectors to the 4-pole
jack plug as shown. Apply silicon paste on all
locations
as
shown.
Silicon paste
Note: Must be done to avoid corrosion.
•
•
Apply silicon paste to the instrument connection pins at the back of the instrument.
Press the jack plug onto the instrument pins. Press the cable in to the cable leads.
Mount the connection back cover with the screw.
12
SPEED
3.1.4
Installing instrument to the Server
All NX2 instruments are connected directly to the Nexus Network
in a daisy chain. They all use the same colour coded 4-pole jack
plugs.
3.1.5
Installing the transducer direct to the instrument.
If you use the NX2 speed as a stand alone unit (not in a Nexus
Network), the transducer and the power supply are connected
direct to the instrument.
1.
2.
3.
4.
Disconnect the connector on the transducer cable (only used
when connecting to Server
Connect the transducer to the instrument as below
Connect power to the instrument, always remember to use a
3 Amp fuse between the battery and the instrument
Note that there are no power on/off switch on the instrument.
In order to switch of the instrument, a external switch has to
be added on the red +12V cable.
Screen
Red
White
Black
Yellow
Green
3A Fuse
13
SPEED
3.1.6
Installing transducer to the Server
The log transducer are supplied with a connector for quick
connection to the server.
Screen
White
Yellow
Green
14
SPEED
4
First start
4.1
Initialising the instrument
Only in a Nexus Network
At power on, the instrument will perform a self test. The display
will first show all segments, then the software version number and
the Nexus Network ID number.
At first power on after installation, you will be asked to press SET
(PrESkey). This will give the instrument a logical ID number on the
Nexus Network.
To initialise the instrument, press SET on all installed digital
instruments, one at the time.
Note: Always wait for the text ”Init OK”
to be displayed, before you press SET
on the next instrument!
The Server automatically gives the first unit ID number 16, then
17 and so on. The order in which you press SET is the same
order as the instruments will be given a logical ID number on the
Nexus Network.
The example shows that the instrument version number is 2.0 and
the given logical ID number is 16.
4.2
Re-initialising the instrument
If two instruments by mistake have the same ID number, this can
cause disturbance and block the information on the Nexus data
bus.
To re-initialise the instrument, press CLEAR during the power up
sequence when version and ID numbers are displayed.
The display self test is then re-started on all instruments and you
will be asked to press KEY on each instrument as explained
above.
15
SPEED
Note! If you do not succeed to re-initialise, we suggest you
disconnect all but one instrument with the same ID number, then
repeat the above procedure.
16
SPEED
5
Operation
5.1
About this manual
•
In this manual each time a push-button is refereed to, the
push-button name will appear in bold and CAPITAL letters
example PAGE.
•
Unless otherwise
momentary.
•
Each time a function is mentioned in the text, it will be in
brackets and in the same format, where possible, as
displayed, ex. (TRP).
stated
the
push-button
17
presses
are
SPEED
5.2
How to use the push-buttons
PAGE
SIGN
MAIN
FUNCTION
SUB
FUNCTION
CLEAR
5.2.1
MINUS
PAGE
PLUS
PAGE
The PAGE button is used to move the cursor when in edit mode.
A press on PAGE moves the cursor in a circular pattern, one step
to the right for every press.
A press on PAGE and MINUS together, back steps cursor to the
preceding step.
5.2.2
MINUS
A press on MINUS moves to the next sub-function.
In edit mode it decreases to the previous digit.
5.2.3
PLUS
A press on PLUS moves to the previous sub-function.
In edit mode it increases to the next digit.
5.2.4
SET
A press on SET unlocks a digit to access edit mode.
When unlocked, the digits are ”active” (flashes) and can be edited
by pressing MINUS, PLUS and PAGE as required.
When finished editing, lock the digit by another press on SET.
18
SET
SPEED
5.2.5
Clear / cancel / reset
A press on CLEAR, clear digits, cancel alarms or resets the
counters.
5.2.6
Calibration
To access calibration mode, press and hold SET more than 2
seconds.
2 sec
To return to main-function mode, press SET when the text return
(RET) is shown.
5.2.7
Lighting
The instrument uses red back lighting for the display and the 5
push-buttons. The lighting can be set at 4 different levels.
2 sec
To quick access the light control, press and hold PAGE for more
than 2 seconds. The flashing text (Lit OFF) will be displayed and
the display will be lit momentarily.
To select between the 4 light levels, Press PLUS: LOW, MED,
MAX and OFF. To lock the selected level press SET.
The selected light level will be copied to all NX2 instruments
connected to the system. When the lighting is on, it is not possible
to reduce or turn off the lighting on an individual instrument.
19
SPEED
6
SPEED functions
6.1
SPEED main-function
Boat speed through the water.
Unit available in knots (KT), km/h (Kh) or miles/h (Mh) (See
7.1.2,C11).
6.2
SPEED sub-functions
6.2.1
TRIP LOG (TRP)
0-199,99 NM, only displayed in NM. Distance covered from power
on.
To reset TRIP LOG press CLEAR.
6.2.2
TOTAL LOG (LOG)
0-19999 NM, only displayed in NM. Can not be reset.
6.2.3
MAXIMUM SPEED (MAX)
Maximum speed since power on, or from reset of timer. To reset,
press CLEAR.
6.2.4
START TIMER (STA)
Count down timer from 59 to 1 minutes.
To start the timer from minus 10 minutes (-10’STA) press SET.
The figure 1 in 10 is flashing. If you want to start count down from
10 minutes, press SET.
If you want to start the timer from any other time (59 to 1 minute)
for example minus 5 minutes (-5’STA), press PAGE, MINUS and
PLUS as required to set 5 minutes and start the timer with SET.
When started, displays the count down time in minutes and
seconds.
During the last 10 seconds the alarm will sound once every
second.
6.2.5
TIMER
Elapsed time in hr/min/sec from power on, or from end of start
timer count down. To reset, press CLEAR.
6.2.6
AVERAGE SPEED (AVS)
Average speed from power on, or from reset of timer. To reset
press CLEAR.
6.2.7
DISTANCE (DST)
Covered distance from power on, or from reset of timer. This
distance are reseted when the start timer reach zero.
20
SPEED
6.2.8
DEPTH (unit/DPT) Only in Nexus Network
Depth from the water surface or the keel depending on calibration
setting (See 7.2.3, C22).
Unit available in meters (m), feet (FT) or fathoms
(FA). (See 7.2.2,C21).
The text alternates between the selected (unit) and (DPT).
21
SPEED
7
Calibration
To get the most out of your Nexus Network, it is important to
carefully calibrate the Network. The calibration values are stored
in a non volatile memory.
To access calibration mode, press and hold SET more than 2
seconds.
To select a calibration code, press MINUS, PLUS and PAGE as
required.
To return to normal mode, press SET when the text return (RET)
is displyed.
To change a calibration value, press SET.
To select calibration value, press MINUS, PLUS and PAGE as
required.
To lock the selected value, press SET
In a Nexus Network, all calibration groups are available. The
different calibration routines are divided into five groups:
C10 - calibration of SPEED
C20 - calibration of DEPTH
C30 - calibration of NAVIGATE
C50 - calibration of WIND
C70 - calibration of Network and NMEA settings
For instructions, see the NX2 Multi Control Manual
22
SPEED
If you use the NX2 Speed stand alone, the following
calibration groups are available:
7.1
Calibration of speed C10
7.1.1
C10 Return (RET)
To return to normal mode, press SET.
7.1.2
C11 (Unit KTS)
Unit for speed. Knots (KTS), km/h (K/h) or miles/h (m/h).
7.1.3
C12 (1.25 CAL)
Calibration value for speed and distance (1.00 - 1.99).
Drive the boat a measured distance at normal speed.
Compare the distance with the trip counter.
Calculate the value with the following formula:
True distance from the sea chart :
Log trip counter distance:
The current calibration value:
New calibration value.
T
L
C
N
If you suspect a current in the water,
drive the boat in both directions and
divide trip counter distance by 2.
7.1.4
C13 DAMPING (SEA)
Damping of indicated boat speed through the water. Controls the
response time of speed changes.
To change damping, press SET.
To select damping level, press PLUS and select from:
(LOW) 1 sec, (MED) 5 sec and (MAX) 22 sec.
To store the value, press SET.
Default value is (LOW), for use in calm sea. But if the sea is
rough, you may want to ”stabilise” the readout on the display, then
select (MED) or (MAX). Damping is set separately for each
instrument.
23
SPEED
7.2
C20, calibration of depth
7.2.1
C20 (RET)
To return to normal mode, press SET.
7.2.2
C21 (Unit m)
Unit for depth. Metre (m), feet (Ft) or fathoms (FA).
7.2.3
C22 ( - 00.0 ADJ)
Calibration of the depth transducer position.
This option is used to select whether the displayed water depth is
measured from the water level or the keel.
To measure from the keel, use the minus ( - ) sign.
Example: ( - 01.2 ADJ). The distance from the transducer to the
keel is 1.2 m
To measure from the water surface, use the underlining character
( _ ) sign.
Example: ( _ 00.4 ADJ). The distance from the transducer to the
water surface is 0.4 m.
The selected value will be subtracted or added from the measured
depth.
7.2.4
C23 (Unit°C)
Unit for temperature. Celsius (C) or Fahrenheit (F).
7.2.5
C24 (0°C TMP)
Value for compensation of the temperature.
To add, use underlining character ( _ ) ahead of the digit ( _1
TMP).
To subtract, use minus character ( - ) ahead of the digit (-1 TMP).
24
SPEED
8
Maintenance and fault finding
8.1
•
•
•
•
•
Maintenance
To clean the instrument, use only mild soap solution and rinse
with water.
Do not use detergents or high pressure washing equipment.
At least once a year, check all your connections and apply
additional silicon paste at each connection point.
Always use the instrument cover for protection, when not in
use.
Storing transducers and instruments when not in use for
longer periods: It is advisable to remove the instruments and
transducers, and store them inside the boat or at home in
room temperature, if possible.
8.2
Fault finding
Before you contact your NX2 dealer, and to assist your dealer to
give you a better service, please check the following points and
make a list of:
•
•
•
All connected instrument and transducers , including their
software version numbers.
Server software version number.
Nexus Network data bus ID numbers for each instrument
(displayed at power up).
8.2.1
General
In most cases, the reason for faults in electronic equipment is the
installation or poor connections. Therefore, always first check that:
•
•
•
•
•
•
•
•
•
Installation and connection is made per instructions for
instrument and transducers, (see 2).
Screw terminals are carefully tightened.
No corrosion on any connection points.
No loose ends in the wires causing short cuts to adjacent
wires.
Cables for damage, that no cables are squeezed or worn.
Battery voltage is sufficient, should be at least 10V DC.
The fuse is not blown and the circuit-breaker has not opened.
The fuse is of the right type.
Two instruments do not have the same ID number, (see 4.2).
25
SPEED
8.2.2
Fault - action
1. Speed and distance functions: No reading ( --- )
- C95 (COG) should be OFF, if no navigator is connected.
If wrong speed and distance are displayed, calibrate the unit.
For more information, see manual for NX2 Server.
Irregular values: Check the speed damping (SEA), (see 7.1.4).
9
Specifications
9.1
Technical specifications
Dimensions:
Instrument cable:
Speed log instrument: 113 x 113 x23 mm
(4.3x4.3 inch).
8 m (26 ft).
Power supply:
Power
consumption at 12V:
12V DC (10-16V). The instruments are polarity protected
Temperature range:
Storage:-30°to +80°C (-22°to +176°F)
Operation: -10° to +70°C(14°to +158°F)
Speed log instrument:
260 gram (9.17 oz).
Speed log instrument:
Water proof
Weight:
Enclosure:
Speed log instrument: 0,08W
with maximum lighting 0,8W.
CE approval
The products conforms to the EMC requirements for immunity and
emission according to EN 50 08-1.
26
SPEED
9.2
Optional Accessories
Below find a selection of optional accessories available. Please contact your local NX2
dealer for more information.
22118-3
22118-2
22118-1
22118-4
22118-5
22118-6
NX2 Completes
Multi Control instrument and Server, 8m cable
Multi Control and Server with Speed Log and depth transducer, 8m cable
Speed log with log transducer, 8m cable
Wind Data, with transducer, 25m cable, mast bracket
Compass Data, with transducer 35°, 8 m cable
GPS Navigator, with GPS Antenna, 8+10m cable
22120-1
20707
19915-8
21731
20860
20721
20721-1
20594
21721
69980
21970
21735
NX2/Nexus Transducers
Server compl with 3m power cables
Log/Temp transducer, 8 m cable (for Nexus and Star)
Depth transducer, 8m cable (for NX2 only)
Compass transducer 35°, 8m cable
Compass transducer 45°, 8m cable
Wind transducer, 25m cable, mast bracket
CF-wind transducer, Carbon Fibre, 1260mm long, 380g, no mast cable incl.
Nexus mast cable 25m
MTC (Mast Twist Compensation) box, 8m cable, for Wind Data instr.
MRC (Mast Rotation Sensor Compensation) box
GPS Antenna, with NMEA 0183 output
Bracket for GPS Antenna and 35° Compass transducer for bulkhead mount
22117-1
22117-3
22117-4
22117-5
22117-6
22117-7
NX2 Digital Instruments (all supplied with 0.2m cable)
Speed log instrument
Multi Control instrument
Wind Data instrument
Compass Data instrument
GPS Navigator instrument
Autopilot instrument
22115-01
22115-02
22115-03
22115-05
22115-06
22115-07
22115-08
22115-09
22115-10
22115-11
22115-12
22115-13
NX2 Analog Instruments (all supplied with 0.2m cable)
NX2 Analog Wind Angle
NX2 Analog Steer Pilot
NX2 Analog Speed Trim
NX2 Analog Speed 0-16kts
NX2 Analog Speed 0-50kts
NX2 Analog Depth 0-200m
NX2 Analog Depth 0-600ft
NX2 Analog Rudder angle
NX2 Analog Compass
NX2 Analog GPS Speed 0-16kts
NX2 Analog GPS Speed 0-50kts
NX2 Analog GPS Course
21210
21218-1
20966
Nexus Remote Control Instrument
Remote Control Instrument (RCI), with Autopilot control, 5m cable, bracket
Bracket Remote Control instrument
Connector 4-pole, NEW model (Allows cable - cable connection)
27
SPEED
21680-1
21684-1
69995
Nexus Multi XL
Multi XL instrument, 4m cable (RCI or Multi Center needed to control Multi XL)
Multi XL Set, Multi XL instrument and Remote Control instrument
Mast bracket XL, in aluminium for Multi XL and Nexus / Star 110x110mm instr.
22118-6
22117-6
21970
20992-2
21735
NX2 GPS
GPS Navigator, with GPS Antenna, 8+10m cable
GPS Navigator instrument
GPS Antenna, with NMEA 0183 output
Bracket GPS Antenna, plastic with female thread 1" x 14 tpi
Bracket for GPS Antenna and 35° Compass transducer for bulkhead mount
22117-7
21210
22115-09
Nexus Autopilot components
Autopilot instrument
Remote Control instrument, with Autopilot control, 5m cable, bracket
NX2 Analog Rudder angle
21035-2
20860
21731
21036
69981
Servo Unit A-1510, 8m cable
Compass transducer 45°, 8m cable
Compass transducer 35°, 8m cable
Rudder Angle Transmitter RFU-25, 15m cable, ball joint linkage 230mm x 2
Linear Rudder Angle Transmitter
21134
21134-24
21341
21341-24
21136
69991-12
Pumpset PF-0.3 12V
Pumpset PF-0.3 24V
Pumpset PF-0.3S 12V, with solenoid
Pumpset PF-0.3S 24V, with solenoid
Linear Drive AN-23, stroke 229mm, peak thrust 680kg
Integrated Linear Drive HP-40, stroke 254mm, peak thrust 500kg
28
SPEED
10 Warranty
WARRANTY
GENERAL
All our products are designed and built to comply to the highest class industry standards. If the
products are correctly installed, maintained and operated, as described in the installation and
operation manual, they will provide long and reliable service. Our international Network of
distributors can provide you with the information and assistance you may require virtually anywhere
in the world.
Please read through and fill in this warranty card and send it to your national distributor for
product registration.
LIMITED WARRANTY
The warranty covers repair of defective parts due to faulty Manufacturing and includes labour when
repaired in the country of purchase. The warranty period is stated in the product manual, and
commences from the date of purchase. The above warranty is the Manufacturer’s only warranty
and no other terms, expressed or implied, will apply. The Manufacturer specifically excludes the
implied warranty of merchantability and fitness for a particular purpose.
CONDITIONS
•
The supplied warranty card and receipt with proof of purchase date, must be shown to validate
any warranty claim. Claims are to be made in accordance with the claims procedure outlined
below.
•
The warranty is non-transferrable and extends only to the original purchaser.
•
The warranty does not apply to Products from which serial numbers have been removed,
faulty installation or incorrect fusing, to conditions resulting from improper use, external
causes, including service or modifications not performed by the Manufacturer or by its national
distributors, or operation outside the environmental parameters specified for the Product.
•
The Manufacturer will not compensate for consequential damage caused directly or indirectly
by the malfunction of its equipment. The Manufacturer is not liable for any personal damage
caused as a consequence of using its equipment.
•
The Manufacturer, its national distributors or dealers are not liable for charges arising from
sea trials, installation surveys or visits to the boat to attend to the equipment, whether under
warranty or not. The right is reserved to charge for such services at an appropriate rate.
•
The Manufacturer reserves the right to replace any products returned for repair, within the
warranty period, with the nearest equivalent, if repair within a reasonable time period should
not be possible.
•
The terms and conditions of the warranty as described do not affect your statutory rights.
CLAIMS PROCEDURE
Equipment should be returned to the national distributor, or one of its appointed dealers, in the
country where it was originally purchased. Valid claims will then be serviced and returned to the
sender free of charge.
Alternatively, if the equipment is being used away from the country of purchase, it may be returned
to the national distributor, or one of its appointed dealers, in the country where it is being used. In
this case valid claims will cover parts only. Labour and return postage will be invoiced to the sender
at an appropriate rate.
DISCLAIMER
Common sense must be used at all times when navigating and the Manufacturer’s navigation
equipment should only be considered as aids to navigation.
The Manufacturers policy of continuous improvement may result in changes to product
specification without prior notice.
29
SPEED
File id:
WARRANTY CARD
TO BE RETURNED TO YOUR NATIONAL DISTRIBUTOR
OWNER:
Name:
Street :
City/Zip Code :
Country:
Product name:
Serial number:
A
B
C
1
2
3
4
5
6
7
Date of purchase: _______________Date installed ________________
Dealers stamp:
Tick here if you do not wish to receive news about future products
30
SPEED
31
Copyright ©:
Nexus Marine AB
Kuskvägen 4, 191 62 Sollentuna, Sweden
Tel: +46 -(0) 8 – 506 939 00. Fax: +46 -(0) 8 -506 939 01
www.nexusmarine.se
32
22131-1 Edition 1
SPEED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising