HDMI Extender over Single Cat.X with HDBaseT-Lite, Bi

HDMI PIN DEFINITION
HARDWARE INSTALLATION
1. Connect a HDMI or DVI source (such as a Blu-ray Disc player)
to the transmitting unit 962-T.
2. Connect a HDMI or DVI display (such as a LCD TV) to the
receiving unit 962-R.
3. Connect IR Blaster/Receiver to both TX and RX units.
4. Connect a Cat-5/5e/6 cable between the transmitting and
receiving units.
Type A (Receptacle) HDMI
Pin 1 TMDS Data2+
Pin 8
Pin 2 TMDS Data2 Shield Pin 9
5. Make sure this Cat-5/5e/6 cable is tightly connected and not
TMDS Data0 Shield Pin 15 SCL
loose.
Pin 16 SDA
TMDS Data0–
Pin 17 DDC/CEC Ground
Pin 3 TMDS Data2–
Pin 10 TMDS Clock+
Pin 4 TMDS Data1+
Pin 11 TMDS Clock Shield Pin 18 +5V Power
Pin 6 TMDS Data1–
Pin 13 CEC
Pin 7 TMDS Data0+
Pin 14 Reserved(N.C. on device)
1. All HDMI over CAT5 transmission distances are measured using
4.
5.
6.
7.
Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video
Signal Generator VG-859C & VG-870B.
Incorrect placement of IR Blaster and Receiver may result in the failure
of the IR extenders. Please check carefully before plugging in the IR
extender to the respective IR sockets. Warranty will not cover the
damage.
The transmission length is largely affected by the type of Cat-5/5e/6
cables, the type of HDMI sources, and the type of HDMI display. The
testing result shows solid UTP cables (usually in the form of 300m
[1,000ft] bulk cables) can transmit a lot longer signals than stranded
UTP cables (usually in the form of fixed length patch cords). Shielded
STP cables are better suited than unshielded UTP cables. A solid UTP
Cat-5e cable shows longer transmission range than stranded STP
Cat-6 cable. For long extension applications, solid UTP/STP cables
are the only viable choice.
EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is
recommended for better performance.
To reduce the interference among the unshielded twisted pairs of
wires in Cat-5/5e/6 cable, one can use shielded STP cables to improve
EMI problems, which is worsen in long transmission.
Because the quality of the CAT5/6 cables has the major effect on how
long the transmission limit can achieve and how good is the received
picture quality, the actual transmission range is subject to one’s
choice of Cat-5/5e/6 cables. For desired resolutions greater than
1080i or 1280x1024, a Cat-6 cable is recommended.
If your HDMI display has multiple HDMI inputs, it is found that the first
HDMI input [HDMI input #1] generally can produce better transmission
performance among all HDMI inputs.
Performance Guide for HDMI over Category Cable Transmission
Performance rating
Wiring
Solid
Stranded
Shielding
Type of category cable
CAT5
CAT5e
CAT6
***
***
****
*****
***
****
Unshielded (UTP)
*
**
**
Shielded (STP)
*
*
**
Unshielded (UTP)
Shielded (STP)
Termination
User Manual
receiving unit 962-R and the transmitting unit 962-T.
WARRANTY
NOTICE
3.
6. Plug in 5V DC power supply unit to the power jack of the
Pin 19 Hot Plug Detect
Pin 5 TMDS Data1 Shield Pin 12 TMDS Clock–
2.
HDMI Extender over Single Cat.X with
HDBaseT-Lite, Bi-directional IR and RS-232
Please use EIA/TIA-568-B termination (T568B) at any time
The SELLER warrants the 962 HDMI Extender over Single Cat.X
with HDBaseT-Lite, Bi-directional IR and RS-232 free from defects in
the material and workmanship for 1 year from the date of purchase
from the SELLER or an authorized dealer. Should this product fail to be
in good working order within 1 year warranty period, The SELLER, at its
option, repair or replace the unit, provided that the unit has not been
subjected to accident, disaster, abuse or any unauthorized
modifications including static discharge and power surge. This
warranty is offered by the SELLER for its BUYER with direct transaction
only. This warranty is void if the warranty seal on the metal housing is
broken.
Unit that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of
repair. Such repairs are warranted for 90 days from the day of
reshipment to the BUYER. If the unit is delivered by mail, customers
agree to insure the unit or assume the risk of loss or damage in transit.
Under no circumstances will a unit be accepted without a return
authorization number.
The warranty is in lieu of all other warranties expressed or
implied, including without limitations, any other implied warranty or
fitness or merchantability for any particular purpose, all of which are
expressly disclaimed.
Proof of sale may be required in order to claim warranty.
Customers outside Taiwan are responsible for shipping charges to and
from the SELLER. Cables and power adapters are limited to a 30 day
warranty and must be free from any markings, scratches, and neatly
coiled.
The content of this manual has been carefully checked and is
believed to be accurate. However, The SELLER assumes no
responsibility for any inaccuracies that may be contained in this
manual. The SELLER will NOT be liable for direct, indirect, incidental,
special, or consequential damages resulting from any defect or
omission in this manual, even if advised of the possibility of such
damages. Also, the technical information contained herein regarding
the 962 features and specifications is subject to change without further
notice.
Transmitter
Receiver
rev: 052013
SCP
Safety and Notice
The 962 HDMI Extender over Single Cat.X with HDBaseT-Lite,
Bi-directional IR and RS-232 has been tested for conformance to
safety regulations and requirements, and has been certified for
international use. However, like all electronic equipments, the 962
should be used with care. Please read and follow the safety
instructions to protect yourself from possible injury and to
minimize the risk of damage to the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where
explained in this manual.
Provide proper ventilation and air circulation and do not use
near water.
Keep objects that might damage the device and assure that
the placement of this unit is on a stable surface.
Use only the power adapter and power cords and connection
cables designed for this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always
unplug the power to the device before cleaning.
The 962 HDMI Extender over Single Cat.X with HDBaseT-Lite,
Bi-directional IR and RS-232 boosts up your video/audio transmission
distance up to 60m (198ft) in HDTV 1080p with 48-bit color depth. 962
also supports the most advanced 3D video format complaint with HDMI
specification and therefore guarantees the highest 3D video compatibility
on the market. With only one cost effective Cat.5/5e/6 cable, users can
readily extend HDTV sources from DVD players, Blu-ray Disc player, PS3,
PC, and any other kinds of sources compliant with TMDS to distant
display monitors including HDMI or DVI enabled TV sets or LCD PC
monitors. With the advanced design for the latest HDMI technology, deep
color video, DTS-HD or Dolby TrueHD audio, and HDCP supports and
compatibility are all further insured. This flexibility makes HDCP
compliant DVD players or PS3 transmit utmost high quality video and
audio with a greater distance at the minimal cost, when integrating
several components apart. In addition, 962 is also equipped with
bi-directional IR pass-through path and RS-232 serial port control. These
bonus features allow users to boost IR control distance up to 60m (198 ft)
and makes IR control possible through only single Cat.5/5e/6 cable
including HDMI signals. In addition, serial port offers the convenient path
for interactive application, such as touch panels.
The 962 includes two units: transmitting unit 962-T and receiving
unit 962-R. The transmitting unit is used to capture the input HDMI / DVI
signals with IR control packets and carry the signals via one cost effective
Cat.5/5e/6 cable. The receiving unit is responsible for equalizing the
transmitted HDMI signal and reconstructing IR signals. HDMI-60G offers
the most convenient solution for digital signage with long distance A/V
transmission path, and with 10G transmission width ready, 962 is ready
for your next HDMI generation and applications!
FEATURES
Support HDMI Deep Color & full 3D & [email protected] (HDBaseT-Lite
technology)
Extend the transmission up to 60m (198ft) from the HDMI source at
Full HD 1080p 48-bit and 40m (130ft) at [email protected]
HDCP & EDID Bypass
CEC support
Auto equalization
Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6
cable transmission
DTS-HD Master Audio and Dolby TrueHD high bit rate audio support
Support full frequency IR signal from 20KHz to 60KHz
Bi-directional IR path-through
Full Duplex RS-232 control up to 115,200 bps through connector
Wall mounting housing design for easy and robust installation
i
Model Name
962
Technical
Role of us age
HDMI compliance
HDCP compliance
Video bandwidth
Video support
HDMI over UTP
Audi o support
Equalization
Input TMDS signal
Input DDC signal
ESD protection
PCB stack -up
IR pass -thru
RS -232 support
Input
Output
HDMI source control
HDMI connector
Min DIN connector
RJ -45 connector
Rotary control switch
3.5mm connector
Mechanical
Housing
Model
Dimensions
Package
[L x W x H]
Carton
Model
Weight
Package
Fixedness
Power supply
Power consumption
Operation
temperature
Storage temperature
Relative humidity
962-T
962-R
Transmitter [TX]
Receiver [RX]
HDMI Deep Color , full 3D & [email protected]
Yes
Single -link 340MHz [10.2Gbps]
480i / 480p / 720p / 1080i / 1080p60
[email protected] 60 m (1 98 ft) [CAT5e]
Surround sound [up to 7.1ch) or stereo digital audio
Auto
1.2 Volts [peak -to-peak]
5 Volts [peak -to-peak, TTL]
[1] Human body model — ±19kV [air -gap discharge] & ±12kV [contact discharge]
[2] Core chipset — ±8kV
4 - layer board [impedance control — differential 100 Ω ; single 50 Ω]
Bi -directional
Yes
1x HDMI
1x RJ -45 [HDBaseT]
1x 3.5mm
1x 3.5mm
1x RJ -45 [HDBaseT]
1x HDMI
1x 3.5mm
1x 3.5mm
Controllable via IR pass -through from RX to TX with IR extenders
Type A [19-pin female]
DIN -9
WE/SS 8P8C (Reverse Mode)
None
IR receiver / IR blaster
IR receiver / IR blaster
962-T
962-R
Metal enclosure
73 x 8 9 x 26mm [ 2.9 " x 3. 5" x 1"]
175 x 1 25 x 216 mm [ 6.8 " x 4.9" x 8.5 "]
647 x 366 x 237 mm [ 2'1" x 1' 2" x 9.3 "]
200g [7oz]
196 g [ 6.9 oz]
900g [2 lbs]
Wall -mounting case with screws
5V 2A DC
3 Watt [max]
7 Watt [max]
PACKAGE CONTENTS
1x IR blaster
1x IR receiver
0~40°C [32~104°F]
-20~60°C [ -4~140° F]
20~90% RH [no condensation]
Transmitting unit - 962-T[R]
[Receiving unit]
ON [� ](DTE)
PIN#1
OFF [� ](DCE)
PIN# 2
ON [� ]
OFF [� ]
IR Extenders
IR Blaster
IR Receiver
IR Sockets
IR RECEIVER: plug in the IR receiver to receive all IR command signals
from the IR remote controls of the corresponding devices.
Latch-locking power jack: Connect to 5V DC power
supply
LED: Power indicator
HDMI IN[OUT]: Connects to a HDMI source[Display]
with a HDMI male-male cable
IR Receiver: Infrared 3.5mm socket for plugging in
the extension cable of IR receiver
IR Blaster: Infrared 3.5mm socket for plugging in
the extension cable of IR blaster
Dip Switch: Setup the RS-232 mode for serial
communication channel
RS-232: Connect to host/device serial port
with a DSUB-9 male-male cable here
RJ45: Plug in a Cat-5/5e/6 cable that needs to be
linked to the TX or RX.
LED: TX/RX link indicator
DIP Switch Position
TX & RX
IR PASS-THROUGH
IR BLASTER: plug in the IR blaster to emit all IR command signals received
from the IR receiver from the other end to control the devices
corresponding to the IR signals.
PANEL DESCRIPTIONS
The length depends on the characteristics and quality of the
cables. Higher resolutions and longer transmission distances
require low skew cables (<25ns/100m) for best performance.
Unshielded CAT6 with metal RJ45 connectors is
recommended.
1x 962-T & 962-R
2x 5V DC power supply
1x User Manual
CONNECTION DIAGRAM
SPECIFICATIONS
INTRODUCTION
!
Incorrect placement of IR Blaster and Receiver may result in
the failure of the IR extenders. Please check carefully before
plugging in the IR extender to the respective IR sockets.
Warranty will not cover the damage.
Definition of IR Earphone Jack
1. IR Signal
2. Grounding
IR Blaster
1. IR Signal[20-60 kHz]
2. Grounding
3. Power
IR Receiver
Description
TxD: The 2 nd pin of RS -232, which is in charge of sending data
RxD: The 3 rd pin of RS -232, which is in charge of receiving data
TxD: The 3 rd pin of RS -232, which is in charge of sending data
RxD: The 2 nd pin of RS -232, which is in charge of receiving data
Firmware Update
Normal
i
You can buy any IR extension cables in the market that are
compatible to the definition of the IR sockets for the matrix if
necessary for replacement use. However, IR cables longer
than 2m (6-ft) may not work.