Fenix E‐CP Flashlight
Technical Parameters
ANSI/ PLATO FL1
Output
Turbo
High
Med
Low
Eco
Strobe
1600
350
150
30
3
1600
lumens
lumens
lumens
lumens
lumens
lumens
2 hours
8 hours
20
84
504
30 minutes *
30 minutes
hours
hours
hours
222
105
33
10
meters
meters
Runtime
/
69 meters
Distance
/
meters
meters
12400
2750
1200
270
25
candela
candela
candela
candela
candela
/
Intensity
1 meter
Impact Resistance
IP68
Submersible
Note: According to the ANSI/PLATO FL1 standard, the above specifications are from the results produced by Fenix
through its laboratory testing using a 5000mAh battery under the temperature of 21±3°C and humidity of 50% ‐
80%. The true performance of this product may vary according to different working environments and actual
battery status.
*The Turbo output is measured in a total of runtime including output at reduced levels due to temperature or
protection mechanism in the design.
Warning
Do place this light out of the reach of children!
Do NOT shine the light directly into the eyes of anyone!
Do NOT shine flammable objects at close range, to avoid burning objects or causing danger
due to high temperature!
Do NOT use the light in inappropriate ways such as biting in the mouth, to avoid personal
injury or life threats when the light or internal battery fails!
This light will accumulate a lot of heat while working, resulting in a high temperature of the
flashlight shell. Pay attention to safe use to avoid scalding.
Turn off and lock the light or remove the battery from the light to prevent accidental
activation when the light is placed in a closed and flammable environment such as pockets
and backpacks!
The LED of this flashlight is not replaceable; so the whole light should be replaced when the
LED reaches the end of its life.
Product Features
1600 lumens maximum output and 222 meters maximum beam distance.
A Luminus LED with a lifespan of 50,000 hours.
Built‐in a 5000 mAh rechargeable battery.
Anti‐slip body design ensures a firm grip.
The light tail features a power bank function supporting 18W fast charging and discharging.
Electronic lockout function avoids accidental activation.
Boot‐up battery level indication and low‐voltage warning.
Made of durable A6061‐T6 aluminum.
Premium type HAIII hard‐anodized anti‐abrasive finish.
5.43’’ x 1.10’’ / 138 x 28 mm.
6.00 oz / 170 g (including battery).
Operating Instruction
On/off
With the light unlocked, press and hold the side switch for 0.5 seconds to turn on/off the light.
Instant Strobe
With the light unlocked, press and hold the side switch for 1.2 seconds to enter Strobe mode,
single click again to return to the previously used output of General mode.
Output Selection
In General mode, single click the side switch to cycle through Eco→Low→Med→High→Turbo.
Lock/Unlock
Lock: with the light unlocked and switched off, double click the switch within 0.5 seconds to lock
the light, the light will blink twice on Low to indicate locked status.
Unlock: with the light locked, double click the switch within 0.5 seconds, the light will be
unlocked and activated on Eco. When charging the flashlight, it also will be unlocked.
*In locked status, clicking or pressing the switch will activate 2 one‐second blinks on Low to
indicate locked status.
Intelligent Memory Circuit
The light memorizes the last selected output excluding Strobe mode. When turned on again the
previously used mode will be recalled.
* The High mode will be activated when turned on again if the light is turned off on Turbo mode.
Charging
1. Open the anti‐dust cap, plug the USB Type‐C socket of the charging cable into the light and the
other end of the charging cable into an electrical outlet.
2. When charging, the charging indicators will flash from left to right to display charging status.
The four indicators will be constant‐on after charging is complete.
3. A 5V/2A or higher‐power adapter must be used for charging this light. The normal charging
time is approximately 2 hours from depletion to full charging, with the 18W or higher‐power fast
charging adapter, and the charging time is approximately 3.5 hours with a 5V/2A adapter.
4. Only Eco, Low and Med modes are available when charging, but the charging time will be
prolonged.
5. Be sure to close the anti‐dust cover once charging is completed to maintain the dustproof and
waterproof ability.
Power Bank Function
1. Switch off the light and open the anti‐dust cap, plug the USB A socket of the charging cable
into the USB‐A port of the light, then connect the other end of the charging cable to the charging
port of the digital device to be charged. Or the USB Type‐C port of the light can be used as the
discharging port, in this way, use a proper charging cable with a USB Type‐C port.
2. Properly connect the light and the device to be charged via the charging cable to begin
discharging, the indicators will recede from right to left to display the status. Only Eco, Low and
Med modes are available when discharging.
3. Be sure to close the anti‐dust cover once discharging is completed.
Note:
1. The USB‐A port of the light ONLY supports discharging and the USB Type‐C port of the light
supports charging and discharging. Both ports support 5V/2.4A, 9V/2A, 12V/1.5A. The fast
charging function only normally works when charging cable, adapter and the digital device to be
charged support fast charging. The included charging cable supports fast charging function.
2. Timely charge the light to ensure the normal life of the battery when the battery power is too
low.
3. Recharge a stored light every four months to maintain the optimum performance of the
battery.
Battery Level Indication
With the light switched off, single click the side switch to check the battery status, which will last
for 5 seconds.
Four lights on: 80% ‐ 100%
Three lights on: 60% ‐ 80%
Two lights on: 40% ‐ 60%
One light on: 20% ‐ 40%
One light flashes: less than 20%
Note: When charging the light or using the power bank function, the indicators will constantly
indicate the battery status, and when using the light, the indicators will intermittently indicate
the battery status.
Intelligent Overheat Protection
The light will accumulate a lot of heat when used on High or Turbo modes for extended periods.
When the light reaches a temperature of 50°C or above, the light will automatically step down a
few lumens to reduce the temperature. When the temperature drops below 50°C, it will then
allow the user for the reselection of High or Turbo modes.
Low‐voltage Warning
When the voltage level drops below the preset level, the flashlight is programmed to downshift
to a lower brightness level until Eco output is reached. When this happens in Eco output mode,
the light blinks 3 times every 5 minutes to remind you to timely recharge the battery.
Usage and Maintenance
Disassembling the sealed head can cause damage to the light and will void the warranty.
Lock the light to prevent accidental activation during storage or transportation.
The light may flicker, shine intermittently or even fail to illuminate for the following reasons:
A: Poor battery level.
Solution: Recharge the light.
B: The light has been locked.
Solution: Double click the switch to unlock the light.
If the above methods don't work, please contact your authorized distributor.
Included
Fenix E‐CP flashlight, USB Type‐C charging cable, Lanyard, User manual, Warranty card
IMPORTANT SAFETY INSTRUCTIONS
WARNING ‐ When using this product, basic precautions should always be followed, including the
following:
Read all the instructions before using the product.
To reduce the risk of injury, close supervision is necessary when the product is used near
children.
Do not put fingers or hands into the product.
Do not expose power bank to rain or snow.
Use of a power supply or charger not recommended or sold by power pack manufacturer
may result in a risk of fire or injury to persons.
Do not use the power bank in excess of its output rating. Overload outputs above rating may
result in a risk of fire or injury to persons.
Do not use the power bank that is damaged or modified. Damaged or modified batteries
may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Do not disassemble the power bank. Take it to a qualified service person when service or
repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
Do not expose a power pack to fire or excessive temperature. Exposure to fire or
temperature above 100°C may cause explosion. The temperature of 100°C can be replaced
by the temperature of 212°F.
Have servicing performed by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the product is maintained.
Switch off the power bank when not in use.
SAVE THESE INSTRUCTIONS
">