Posh 2213361 Domaine Brass Single Rail Shower 3 Functions Installation Instructions

Posh 2213361 is a twin shower system that provides a versatile showering experience, allowing users to choose from three different functions. With its brass construction and chrome finish, it adds style and durability to your bathroom. The system requires a minimum operating pressure of 150kPa/1.5bar and is best suited for use with mains pressure water supplies. It comes equipped with all the necessary components for a complete installation, including wall boss housings, mounting brackets, screws, and a rail.

PDF Download

Document

TWIN SHOWER
TWIN SHOWER
SYSTEM
Installation
Installation
Guide Guid
Installation Instructions
Technical Specifications:
Technical Specifications:
97-2913
Mar-2018
Operating Pressure:
Operating Pressure:
Min: 150kPa/1.5bar
Min: 150kPa/1.5bar
Max: 500kPa/5.0bar*
Max: 500kPa/5.0bar*
Optimum: 150kPa/1.5bar - 500kPa/5bar
Optimum: 150kPa/1.5bar - 500kPa/5bar
Recommended installation of pressure
Recommended installation of pressure limiting
valve if supply exceeds 500kPa
valve if supply exceeds 500kPa
Posh Domaine Brass Rail Shower 3 Functions Chrome (4*)
ortant Installation Considerations
Operating Temperature:
Hot: Max 80&deg;C*
Cold: Min 5&deg;C
TE: Some showers
may not provide
an effective
shower when used
Important
Installation
Considerations
gravity fed heated water systems or where pressures are less
150kPa at the outlet.
Additionally
showers
with
ratesan
ofeffective
less
1. NOTE:
Some showers
may
notflow
provide
shower when used
9L/min may not with
allowgravity
the following
to
function
correctly:
fed heated water systems or where pressures are less
me instantaneousthan
water
heaters
150kPa
at the outlet. Additionally showers with flow rates of less
me tempering valves
than 9L/min may not allow the following to function correctly:
me thermostatic _mixing
somevalves
instantaneous water heaters
me shower heads_ some
only operate
correctly
tempering
valveswhen hot and cold water
lies are both mains
pressure
and may mixing
not be valves
suitable for some
_ some
thermostatic
ntaneous hot water
services.
2. Some shower heads only operate correctly when hot and cold water
hen water pressure
is in excess
of 500kPa
a pressure
device
supplies
are both
mains pressure
andlimiting
may not
be suitable for some
quired in accordance
with AS/NZS
recommendation
instantaneous
hot3500
water1.12
services.
Operating Temperature:
Inlet Connections:
Hot: Max 80&deg;C*
Cold: Min 5&deg;C
All &frac12;&quot; BSP
NOTE:
Inlet
NOTE: Connections:
- After installation all connections must
All
&frac12;&quot; BSP
- After
installation all connections must be
checked for leaks
checked for leaks
- All installations must be carried out in
- All installations must be carried out in
compliance with relevant water regula
compliance with relevant water regulations*.
3. When water pressure is in excess of 500kPa a pressure limiting device
is required in accordance with AS/NZS 3500 1.12 recommendation
* Regional specific regulations apply.
* Regional specific regulations apply.
Please refer to your warranty statement
Please refer to your warranty statement at
www.methven.com
www.methven.com
Step 2
• Match the m
into place.
Methven
warrants
product against
manufacturing
defects
andforthat
ven warrants this
product
againstthis
manufacturing
defects
and that it is
suitable
useit is suitable for use
under
the
general
operating
conditions
specified
in
this
instruction
sheet.
IMPORTANT:
Please
read
all
of
the
r the general operating conditions specified in this instruction sheet. However, regional However, regional
regulations
apply
and
may affect
your
warranty.
Please refer to Self Tapping Screw
instructions
before
installation.
ations apply and
may affect
your
warranty.
Please
refer
to
customer
service
for
full
details.
mer service for full details.
Zealand
0 804 222
284
• Slide the rai
• Remove the
General:
New Zealand
0800 804 222
•
98-0284
•
*This
product must beAustralia
installed in
Australia
compliance with all1300
relevant
638regional
483
1300 638 483
regulations.
UK
UK
0800
195 1602
0800 195 1602
Slider
Wall Plug
It is the responsibility of the installer to
ISSUE A
ISSUE A
ensure a waterproof seal is achieved
DECEMBER
2015
between the product and mounting DECEMBER 2015
surface. If in doubt about the quality of
the seal, remove the product and
Elbow
reinstall using silicone to ensure a seal is
(if supplied)
achieved.
•
All pipe work must be thoroughly flushed
prior to the installation of the hose.
•
After installation all connections must be
checked for leaks.
•
All outlets used primarily for personal
hygiene shall deliver water at a safe
temperature as per regional regulations.
• To adjust sli
handle to un
Grub Screw
Grub Screw
Topside
1850mm (Recommend
655mm Rail 555mm (Recommended)
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Step 3
Rail
Internal
Mounting
Bracket
Step 1
• Mount the wall boss housings in
desired position with the screws. Check
the mounts are vertically aligned.
Ensure the grub screws are located on
the correct sides as shown.
• Relocate th
screws top
Page 1 of 3
prior to the installation of the hose.
•
After installation all connections must be
checked for leaks.
•
All outlets used primarily for personal
hygiene shall deliver water at a safe
temperature as per regional regulations.
Mounting
Bracket
handle to unlock
Grub Screw
Step 1
Grub Screw
Topside
Step 2
• Match the mounting brackets to wall bosses and push
into place.
• Slide the rail up or down to centralise the brackets.
all Plug
• Remove the rail and tighten the tensioning screws firmly. Grub Screw
1850mm (Recommended)
655mm Rail 555mm (Recommended)
• Mount the wall boss housings in
desired position with the screws. Check
the mounts are vertically aligned.
Ensure the grub screws are located on
the correct sides as shown.
Underside
• Relocate the rail onto wall bosses and tighten grub
screws top and bottom.
FLOOR
Rail
ernal
unting
cket
Step
Step 32
adjust
position,
rotate
•• To
Match
theslider
mounting
brackets
tothe
wallslider
bosses and push Unlock
handle
to
unlock
and
lock
the
slider
as shown.
into place.
• Slide the rail up or down to centralise the brackets.
all Plug
• Remove the rail and tighten the tensioning screws firmly.
• Relocate the rail onto wall bosses and tighten grub
screws top and bottom.
Lock
crew
Rail
Step 3
ernal
unting
cket
1850mm (Recommended)
crew
• To adjust slider position, rotate the slider
handle to unlock and lock the slider as shown.
Unlock
Lock
Page 2 of 3
1850mm (Recom
Elbow Installation (if supplied):
m
ROUND
Installati
2m
10&plusmn;
Step 1
• Wall lining hole should be cut or finished as per
the dimension shown in the diagram on the right.
• Cut off the threaded nipple 10&plusmn;2mm from the wall
lining and apply thread seal tape to ensure a
good seal.
Technical Spe
26mm max
Inlet Connection
All &frac12;&quot; BSP
* Regional specific re
Please refer to your w
www.methven.com
Step 2
• Screw the elbow onto the nipple ensuring
that the o-ring is sufficiently compressed to
create a watertight seal.
• Ensure that the elbow is oriented vertically
with the outlet oriented downwards.
Step
3 Cleaning:
Care
and
Handset
Never
use abrasives
abrasive
agents to clean this product. Clean regularly with
• Connect
hose to or
outlet
elbowcleaning
and handset.
contamination free warm soapy water and a damp soft cloth.
m
• Ensure swivelling cone is connected to the
2m
10&plusmn;
Elbow
Installation
(if
supplied):
Periodically
handset.the filter washer should be removed from the end of the shower hose and cleaned.
Flat
Washer
Step 1
Filter Washer
as per
• Wall lining hole should be cut or finished
the dimension shown in the diagram on the right.
• Cut off the threaded nipple 10&plusmn;2mm
from theCone
wall
Non-Swivelling
lining and apply thread seal tape to ensure a
good seal.
Swivelling
Cone
26mm max
ROUND
Installati
Technical Spe
Inlet Connection
All &frac12;&quot; BSP
* Regional specific re
Please refer to your w
www.methven.com
Step 2
• Screw the elbow onto the nipple ensuring
Methven
this product
against manufacturing
defects and that it is suitable for use
that thewarrants
o-ring is sufficiently
compressed
to
create
watertight
seal.
under
thea general
operating
conditions specified in this instruction sheet. However, regional
and may
affect vertically
your warranty. Please refer to www.methven.com or call
Ensure thatapply
the elbow
is oriented
•regulations
customer
service
for
full
details.
with the outlet oriented downwards.
New Zealand
0800 804 222
Care and Cleaning:
Australia
1300 638 483
UK
0800 195 1602
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with
98-0338
contamination free warm soapy water and a damp soft cloth.
ISSUE B
JUN 2016
Periodically the filter washer should be removed from the end of the shower hose and cleaned.
Page 3 of 3
Methven warrants this product against manufacturing defects and that it is suitable for use
under the general operating conditions specified in this instruction sheet. However, regional
regulations apply and may affect your warranty. Please refer to www.methven.com or call
customer service for full details.
">

Hello! I am an AI chatbot specifically trained to assist you with the Posh 2213361 Domaine Brass Single Rail Shower 3 Functions Installation Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated