MILLI EDGE MK2

DIVERTER MIXER

60

5

58 - 75

ADJUSTMENT page 1 of 2

13

35

4

SPECIFICATIONS

Recommended Use

Finish Available

Pressure Rating

Temperature Rating

Suitable Hot Water

Standards

Domestic, hotel and commercial

Chrome

Maximum continuous operating pressure 500 kPa.

Note: For best performance and longer life, we recommend 150-500 kPa.

Maximum continuous working temperature 75 o C

Storage Tank: Yes

Continuous Flow: Refer to manufacturer of continuous hot water systems

Gravity Feed: No

AS/NZS 3718

CLEANING RECOMMENDATIONS

We recommend the use of soapy water or approved cleaners.

This product should not be cleaned with abrasive materials.

Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions.

To see the complete MILLI EDGE range go to www.reece.com.au/bathrooms

AS/NZS 3718

WM-025901

Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.

Tech Page Version 1

MILLI EDGE MK2

DIVERTER MIXER

page 2 of 2

INSTALLATION INSTRUCTIONS

Important Note

Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. Your mixer comes to you already factory assembled and tested. We do not recommend the dismantling of any internal part of the mixer. The mixers are factory tested and sealed so as to give the best performance.

53mm to 75mm

Adjustment

Screw the diverter mixer assembly in place. Attach water supplies.

Test and check for leaks

Do not remove Protective

Covers until final fit-off.

Cut a 40mm hole and a

45mm hole in cement sheet and tiles, 60mm apart, as shown.

40mm

INSTALLATION INSTRUCTIONS

DIVERTER MIXER

IN0288 REV B

CARTRIDGE REPLACEMENT

Removing Diverter: a) Unfasten and remove the Diverter Handle.

b) Pull the Dress Plate off the Mixer Assembly c) Unscrew and remove the Diverter Shroud with a 27mm tube spanner.

d) Unscrew and remove the Diverter Cartridge with a

21mm tube spanner.

Installing Diverter: a) Install the Diverter Cartridge with a 21mm tube spanner.

b) Install the Diverter Shroud with a 27mm tube spanner.

c) Push the Dress Plate back on the Mixer Assmebly d) Turn spindle Anti-Clockwise until it stops.

e) Fasten the Diverter Handle to the Diverter Cartridge.

Noggin

Cement sheet and Tiles

45mm

Hot

Inlet

Outlet 1

Outlet 2 recommended working pressure maximum hot water temperature

Cold

Inlet

Outlet 1

180°

Outlet 2

Remove the protective covers.

Gently push Dress Plate onto Mixer Assembly

Dress Plate

Attach Mixer Handle and Diverter Handle to Mixer Assembly.

Fasten Grub Screws firmly with Allen key supplied.

Insert Screw Caps and press firmly in place.

Grub Screw

Screw Plug

Mixer Handle

Grub Screw

Handle Screw Plug

NOTE:

- If the pressure exceeds or is likely to exceed 550kpa,

an approved pressure limiting device must be installed.

- Flush out all pipe work prior to installation.

- If the water temperature exceeds 75°C, an approved

tempering valve must be fitted.

- Installation should comply with Australian standard

AS3500.1 or relevant local authority requirements.

Showers may not be suitable for use within:

• Gravity-fed water systems

• Some instantaneous hot water systems; or

• Pressure supply less than 150kPa;

NOTE:The 500kPa maximum water supply pressure does not apply to fire service outlets.

Failure to comply with the above may void all warranties.

WARRANTY:

Please refer to the full warranty statement enclosed with the product before installing.

MAINTENANCE AND CARE:

- Products should be cleaned with mild

liquid detergent or soap and water.

- Do not use cream cleaners or citrus

based cleaning products, as they are

abrasive.

- Use of unsuitable cleaning agents may

damage the surface. Any damage caused

in this way will not be covered by

warranty.

DISCLAIMER:

While we aim to ensure the specifications shown are correct at the time of printing, we reserve the right to make modifications without prior notice. Always use the physical product measurements for mark-ups and roughing-in as the line drawing shown may differ from the actual product over time.

*All measurements are shown in millimeters.

Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference