G9X User Manual - Touratech-USA
G9x / G9x PowerSet™
User
Guide
CONTENTS
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6.3 LISTENING TO MUSIC VIA A2DP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. CHARGING THE BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6.4 MUSIC SHARING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3. C ARDO COMMUNITY PLATFORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.1 GENERAL FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.2 STATUS LIGHTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.3 AUDIO SOURCES AND PRIORITIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.4 VOICE COMMAND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.5 SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6.5 LISTENING TO MUSIC VIA THE AUX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. FM RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.1 RADIO TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.2 AUTOMATIC RADIO TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9. SUPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
10. NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.6 VOICE CONNECT (VOX). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. INTERCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.1 “ONE+8” INTERCOM TOGGLING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.2 INTERCOM WITH CHANNELS “A” AND “B”. . . . . . . . . . . . . . . . . . . . . . . . 9
5.3 CLICK-TO-LINK (CTL) INTERCOM MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.4 BUSY SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.5 RECEIVING INTERCOM CALLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.6 GROUP SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6. PAIRING AND USING A MOBILE PHONE, GPS OR MP3 PLAYER . . 12
6.1 PAIRING BLUETOOTH CHANNELS 1 AND 2 . . . . . . . . . . . . . . . . . . . . . . 12
6.2 MAKING AND RECEIVING PHONE CALLS. . . . . . . . . . . . . . . . . . . . . . . . 13
2
| scala rider® G9x / G9x PowerSet
IMPORTANT:
This is version 1.0 of the User Manual. Please note, that our manual is
periodically updated on the Cardo website to include the very latest
features and functions .
Please visit www.cardosystems.com/download/manuals to check
if the manual you are holding is the most updated version and to
download the manual in your preferred language.
Thank you for choosing the scala rider G9x™ Bluetooth®
communication and entertainment system for motorcycle helmets.
This manual will help you set up, configure and operate it.
If you have purchased the G9x PowerSet, your retail box contains
two factory-paired units.
Among others, the scala rider G9x offers the following key features:
INTERCOM OPTIONS
• Intercom Conference mode between 2, 3 or 4 riders at a range of
up to 1.6 km*
• Click-to-Link® Intercom: For spontaneous connection with other
CTL-enabled riders nearby
• “One+8” Intercom Toggling with 8 additional buddies
MULTIPLE DEVICE CONNECTIVITY
• Bluetooth Mobile phones / GPS device
• Wireless MP3 connectivity via A2DP - cable option also provided
ENTERTAINMENT OPTIONS
• Wireless music streaming via devices supporting Bluetooth Stereo
A2DP and AVRCP profiles
• Music Sharing: Rider and Passenger can enjoy the same stereo
music (via A2DP)
• MP3 Players (non-Bluetooth) via cable
• Built-in FM Radio with 6 station presets and automatic tuning
CARDO COMMUNITY®
• Download software upgrades, enhancements and new features
• Set up your “One+8” Intercom buddies
• Create, find and join riding tours
• Customize your scala rider G9x settings
ADVANCED TECHNOLOGY
➤V
oice Command and V
OX technology:
• Make / Receive mobile calls by voice command
• Make intercom calls by voice command
➤A
GC technology (Automatic Gain Control), allowing the
automatic adjustment of volume according to ambient noise
and riding speed. You can also control the volume level
manually. AGC sensitivity levels can be customized to suit your
personal preferences
➤V
OX technology and Voice Command for safe and handsfree operation of key functions. VOX sensitivity levels can be
customized to suit your personal preferences
➤P
LC software (Packet Loss Concealment) for real-time
compensation of audio losses in challenging environments.
➤A
dvanced software updates via PC/Mac
➤ S poken status announcements, so that you always know to
whom or to what device you are connected
➤V
olume Per Mode: Volume is set and saved at different levels for
each audio source
We wish you a great scala rider G9x experience and encourage you
to write us at support@cardosystems.com with any questions,
suggestions or comments you may have.
* Under tough environmental conditions (dense forest, narrow buildings, heavy
traffic), intercom range will be reduced. Once conditions improve, the range will
increase again.
scala rider® G9x / G9x PowerSet | 3
English
1. INTRODUCTION
Mobile button (On / Off)
Volume
Volume
/ Rewind
/ Forward
Channel A / MP3
Voice Command
Channel B / FM
scala rider G9x button layout
2. CHARGING THE BATTERY
Make sure that the battery is fully charged for at least 4 hours
before initial use.
3. CARDO COMMUNITY PLATFORM
The Cardo Community is one of the most remarkable and groundbreaking features of the scala rider G9x.
Visit http://community.cardosystems.com in order to get the
following features:
• “ One+8” Intercom: The scala rider G9x allows Intercom toggling
with up to 8 other individual riders
• IC-to-Phone: When “One+8” Intercom Buddies are out of range,
divert calls via mobile phone.
• Download and install the latest software upgrades
• Configure your own Buddy name (alias) for the “One+8”
Intercom mode and personalize the settings of your scala rider
G9x through your PC / Mac*
• Find your friends and add them to your “One+8” Buddy list
• Create and join tours and invite your friends
Charging with the wall charger is faster than via a computer USB port.
• RED LED ON – Charging • RED LED OFF – Charging complete.
iPhones running iOS 5 and up have a Bluetooth headset battery
indicator feature, to view the battery level of your scala rider on
your iPhone’s screen. The icon appears automatically once you
have paired and connected the scala rider to the iPhone. For more
info, consult the status icons section in your iPhone’s user guide.
Battery
Check
4
In Standby, press for 2 seconds.
• BLUE = Full • PURPLE = Half • RED = Almost empty
| scala rider® G9x / G9x PowerSet
*Minimum Requirements:
Windows® XP™ / Mac OS X 10.5
The scala rider G9x is waterproof and dustproof. However,
when in use, the USB silicone cover should be kept tightly
closed to prevent moisture from entering the unit.
4.2 STATUS LIGHTS
4.1 GENERAL FUNCTIONS
Power ON / OFF
Press
for 2 seconds
• ON: 3 BLUE flashes + ascending tone
• OFF: 3 RED flashes + decending tone
Volume
Tap or to adjust and set volume of current
audio source
Mute
Tap
Battery level
indicator
In Standby, press
and
simultaneously
for 2 seconds
• Blue LED = Full charge
• Purple LED = Half charge
• Red LED = Almost empty
Enter Settings Menu
In Standby, press and for 2 seconds and
follow the spoken instructions
Hear Your Buddy
Name
In Standby, tap
Paired Device
Indication
In Standby, press
and for 2 seconds
If “One+8” Buddies are within range, purple
LEDs flash for 2 seconds
Group Signal
Tap
Enable / Disable VOX
(For Intercom calls
only)
In Standby, press and for 2 seconds
• Enabled: Blue flash for 2 seconds
• Disabled: Red flash for 2 seconds
Enable / Disable
Spoken Status
Announcements
Press
and
simultaneously
scala rider is OFF
Standby mode – No active audio
2 BLUE flashes every
3 seconds
Active mode – Call in progress / music
or other audio source is ON
1 RED flash every 3 seconds
Standby mode – Battery is low
2 RED flashes every 3 seconds Active mode – Battery is low
Solid RED
Charging
4.3 AUDIO SOURCES AND PRIORITIES
If two connected audio sources try to play audio simultaneously,
your​scala rider G9x automatically determines which audio
source to play through the speakers based on the priority of the
connected devices.
Higher Priority

Lower Priority
1. Mobile Phone or GPS instructions*
2. Intercom
3. A2DP (Stereo Bluetooth) audio
4. FM Radio (Built-in)
5. AUX (for corded connection i.e. Music Players)
*GPS instructions from Smartphone GPS Apps are
prioritized like A2DP audio
A2DP audio priority can be configured to be higher than Intercom
audio priority via the Cardo Community.
twice
and
None
1 BLUE flash every 3 seconds
for 2 seconds
• Incoming mobile phone calls interrupt ongoing intercom calls
• Incoming intercom calls will interrupt ongoing A2DP music
• Click-to-Link, Intercom and “One+8” calls have the same priority:
Click-to-Link requests will not interrupt any type of Intercom call in
progress, and vice-versa
scala rider® G9x / G9x PowerSet | 5
English
4. GETTING STARTED
4.4 VOICE COMMAND
The scala rider G9x allows you to perform certain actions by simply
using your voice. Using advanced Voice Recognition, you can
control the scala rider G9x completely handsfree.
The default Voice Command language is English. Other languages
can be selected via the Cardo Community platform (see section 3)
or via the Settings menu on the unit.
Throughout this manual, features which are available via Voice
Command are marked with the
icon.
1. With no call in progress, tap
or speak any word loudly to
activate VOX
2. Speak a Voice Command from the table below:
Current Mode
Standby / FM /
A2DP / AUX
Desired Action
“One+8” Intercom Call*
Standby
FM Radio
A2DP Music
<<Buddy Name>>*
Intercom call with A or B “Call Intercom”
4.5 SETTINGS
Customize various settings according to your preferences:
• Spoken Status Announcements, i.e. informing you about
connectivity status (default: ON)
• AGC sensitivity level for the speakers (default: Medium)
• VOX sensitivity level for the microphone (default: Medium)
• Click-to-Link Intercom (default: ON)
• A2DP audio / Intercom priority to change priority for A2DP
audio sources (via Cardo Community only)
To change settings:
• Via the Cardo Community platform at
http://community.cardosystems.com (see section 3).
• Via the Settings menu on your unit. The menu is available in
several languages.
Start A2DP
“Music ON”
Turn on FM
“Radio ON”
Turn off FM
“Radio OFF”
Next Station Preset
“Next Station”
Enter Menu
In Standby, press
Previous Station Preset
“Previous Station”
Exit Menu
Press
Stop / Pause A2DP
“Music OFF”
Next Track
“Next Track”
Previous Track
“Previous Track”
*see Section 5.1 for details
6
Say this:
Voice Command performance may vary based on environmental
conditions including driving speed, helmet type and ambient noise.
For improved performance of the Voice Command feature,
minimize wind impact on the microphone by using the large
microphone sponge and closing the visor.
| scala rider® G9x / G9x PowerSet
and
for 2 seconds
for 2 seconds
4.6 VOICE CONNECT (VOX)
VOX Activation
Speak any word loudly into the microphone
Answer a call
Speak any word loudly into the microphone
Reject a call
Remain silent for about 15 seconds
VOX Sensitivity
(Default: Medium)
Adjust via the Settings Menu or the Cardo
Community.
High: Use this setting if it is difficult to activate VOX
Low: Use this setting if it is too easy to activate VOX
VOX Operation
Mode
VOX can be set to activate the Voice Command
(default) or to start an Intercom Call via the Cardo
Community
Enable/Disable
VOX (For Intercom/
Voice Command
only)
In Standby, press and simultaneously for
2 seconds
• Enable: Blue flash for 2 seconds
• Disable: Red flash for 2 seconds
5. INTERCOM
The scala rider G9x allows full duplex intercom communication at a
range of up to 1.6 km (subject to terrain and within line of sight).
Open the antenna for maximum range
To chat with someone via Intercom, first pair your scala rider G9x to
the second unit. Pairing is a one-time process. Once paired, the units
should automatically recognize each other whenever in range.
If you have purchased the scala rider G9x PowerSet, the box contains
two factory-paired units configured to communicate via Channel “A”.
Intercom Compatibility
Your scala rider G9x is compatible with all scala rider intercom
models. In addition, it is also compatible with the cardo SHO-1 and
Schubert’s SRC-System™. Intercom range with other models is limited
to the distance of the device with the shorter range. For more info
please visit www.cardosystems.com/G9xcompatibility.
scala rider® G9x / G9x PowerSet | 7
English
The scala rider G9x offers VOX technology for safe and hands-free
operation of some key functions.
In the Cardo Community you can set VOX to either start an intercom
call or activate the Voice Command.
Intercom communication is possible
of the three
9 x Ione
ider Gusing
r
n
Intercom modes:
a
t
l
o
ercom
Int
us
4W
ay
In
er
t
c
Co n
e+8
”
Intercom Tog
Section “One+8” Intercom
5.1
Toggling Mode
(between scala rider
G9 / G9x and cardo
SHO-1 only)
gl i
io ns
ferencing
“O
n
Opt
m
k-to-Link Spo
Clic
nt
co
an
er
e
a
om
sc
ng
2-way Intercom conversations
within a group of up to eight other
“One+8” Buddies
5.1 “ONE+8” INTERCOM TOGGLING MODE
Pair with up to 8 other devices (“One+8” Buddies) and
connect with them one at a time by saying their name.
5.1a CONFIGURING YOUR BUDDY NAME
Before using “One+8” Intercom, you should assign your device a
Buddy Name, so that other “One+8” participants can call you by
this name.
If you change your Buddy Name, you must pair again with your
“One+8” Buddies for their device to receive your new Buddy Name.
Visit the Cardo Community to configue your Buddy Name (see
Section 3). Until you configure a Buddy Name, your unit will be
known by its generic “One+8” Buddy name, “scala rider G9x”.
Hear Your
Buddy Name
In Standby, tap
and simultaneously. You will hear
the Buddy name of your scala rider G9x through the
speakers.
Play Paired
Buddy List
In Standby, press
for 2 seconds
Section Intercom via Channels Intercom Conferencing (2-way,
5.2
“A” and “B” (with any
3-way and 4-way) using Channels
Cardo intercom model) “A” and “B”
5.1b PAIRING WITH A “ONE+8” INTERCOM BUDDY
There are three ways to pair with “One+8” intercom buddies:
Section
5.3
OPTION 1: Pairing via the Cardo Community®
Easily find and add your friends to your “One+8” Buddy list via the
Cardo Community at: http://community.cardosystems.com
Click-to-Link
(with compatible
models)
1-on-1 spontaneous intercom
conversations with random riders
near you who are not already
paired to your scala rider G9x
OPTION 2: Flash-Pairing™ (with other G9 or G9x models)
Use Flash-Pairing to pair within seconds.
1. Remove both G9 units from their Audio Kits and check
they are in Standby (slow single blue flashing).
2. B
ump the two G9 units gently against each other and hold them
side by side.
8
| scala rider® G9x / G9x PowerSet
K!
5.1d CALLING “ONE+8” INTERCOM BUDDIES
There are two ways to start an intercom call with “One+8” buddies.
OPTION 1: Voice Connect (VOX)
Speak any word loudly into the microphone. When you hear the
Voice Command tone, say the name of a ”One+8” Intercom Buddy
i.e. “John Smith”
3. If Flash-Pairing was successful, a purple light appears for
2 seconds.
☛ OPTION 2: Manual Mode
SAY THE NAME
Press
for 2 seconds. Hear
the names of all pre-paired
“One+8” buddies.
You can also “Flash-Pair” intercom channels “A” and “B” by pressing
either channel button or before bumping the units together.
OPTION 3: S
tandard “One+8” Pairing
(with cardo SHO-1, G9 and G9x models)
1. In Standby, press
for 5 seconds to enter pairing mode.
2. Repeat on the second unit.
3. I f pairing was successful, a purple light appears for 2 seconds.
If your scala rider G9x already has a full list of 8 paired “One+8”
Intercom Buddies, pairing another buddy will replace the buddy
that you have not spoken to for the longest time.
5.1c PAIRED DEVICE INDICATION
You can see which units within a range of 20m are your “One+8”
Intercom Buddies.
Paired Device
Indication
In Standby, press
and for 2 seconds
If “One+8” Buddies are within range, the LEDs on
both units will turn PURPLE for 2 seconds
CHOOSE THE NAME
(from your Buddy List):
Tap
and say the name of
the “One+8” Buddy
When you hear the name of
the Buddy you wish to call,
tap
or say any word loudly
into the microphone.
To cancel Buddy List playback:
Press
for 2 seconds.
If a “One+8” intercom buddy is not in range, or moves out of range,
you have the option to set up the “IC-to-Phone” feature via the
Cardo Community, to remain in contact by diverting Intercom calls
to your mobile phones.
5.2 INTERCOM WITH CHANNELS “A” AND “B”
Start multi-party conversations using Intercom Channels “A” and
“B”. This mode is suitable for 2, 3 or 4-way calls.
scala rider® G9x / G9x PowerSet | 9
English
CLIC
5.2a PAIRING INTERCOM CHANNELS “A” AND “B”
Pairing a channel will replace any existing paired device on that
Channel with the newly paired device.
If you have purchased the G9x PowerSet, both units are factorypaired and configured to communicate via Channel “A”. If for
any reason you have to pair them again, OR if you wish to pair a
different unit to make Intercom calls, proceed as follows:
There are two ways to pair Channels “A” and “B”:
OPTION 1: Flash-Pairing™ (with other G9 or G9x models)
See note in 5.1b
OPTION 2: Standard Channel A / B Pairing (with all models)
1. Check that all units are in Standby.
2. To pair Intercom Channel A – press for at least 5 seconds
until the RED LED begins flashing rapidly.
To pair Intercom Channel B – press for at least 5 seconds
until the BLUE LED begins flashing rapidly.
3. E nter Intercom Pairing mode on the second unit following its
user manual. Both units will now be in Intercom Pairing mode.
4. A
fter a few seconds, both units will show a solid LED for 2 seconds,
indicating that they are paired and ready to use.
5. If Pairing is not completed within two minutes, the units will
return to Standby mode.
5.2b CALLING INTERCOM CHANNELS “A” AND “B”
There are two ways to start an intercom call with Channels “A”
and “B”:
10
| scala rider® G9x / G9x PowerSet
OPTION 1: Voice Connect (VOX)
Speak any word loudly into the microphone. When you hear the
Voice Command tone, say “Call Intercom” to start an intercom call
with “A” and/or “B” (subject to who is present)
VOX Intercom call with only “A” or “B” will end automatically after
30 seconds of silence.
OPTION 2: Manual Mode
☛
Use this to start an Intercom call with either:
• Channel “A”: Tap • Channel “B”: Tap
To end a call tap or again.
If you are already in an Intercom call with “A” or “B”, you can add
another rider (“A” or “B”) by tapping the other channel button, or
another rider can join the intercom call in the same way.
THREE-WAY INTERCOM
Use
C
han
nel “
A”
Rider 2
C
Use
han
nel “
B”
Rider 3
Rider 1
Pairing
Rider “1” is paired to Rider “2” and also to Rider “3”.
1. Rider 1 pairs to Rider 2 using Channel “A” (see 5.2a).
2. Rider 1 pairs to Rider 3 using Channel “B” (see 5.2a).
During a 3-Way Intercom Conference call with 2 other participants,
Rider 1 will not be able to receive mobile phone calls or GPS
navigation instructions as long as the call is in progress.
FOUR-WAY INTERCOM
IMPORTANT: Four-Way Conference Mode Considerations
During a 4-Way Intercom call, the two passengers who maintain two
active connections will not be able to receive mobile phone calls or
GPS instructions as long as the conference call is in progress.
5.3 CLICK-TO-LINK (CTL) INTERCOM MODE
Click-to-Link is a spontaneous, “social” feature of your
scala rider G9x. You can instantly initiate 1-on-1 intercom
calls with other riders near you, without being paired.
Think of it as a private channel that you can set up on-the-go with
other riders that you see along the way.
Click-to-Link can be disabled effectively blocking any attempt by a
third party to send a Click-to-Link request to you.
Pairing
1. Pair Rider 1 to Passenger 2 using Channel “A” (see 5.2a).
2. Pair Rider 3 to Passenger 4 using Channel “A” (see 5.2a).
3. Pair Passenger 2 to Passenger 4 using Channel “B” (see 5.2a).
In this configuration the two passengers (numbered 2 and 4) are
each using two Bluetooth connections:
Start a CTL call request
(search lasts up to 10 sec.)
Double-tap
End a CTL call /
Cancel a CTL call request
Tap
Accept a CTL call
When hearing the CTL ringtone: Tap or
say any word loudly to answer by VOX
Reject a CTL call
While hearing the CTL ringtone:
Remain silent until the ring tone stops or
press or for 2 seconds
Enable / Disable CTL
(Enabled by default)
Via the Settings Menu or Cardo Community
Calling
1. Make sure all four units are in Standby.
2. Passenger 2 should tap to call Passenger 4.
Wait until audio is heard on both units.
3. Rider 1 should tap to call Passenger 2.
4. Rider 3 should tap to call Passenger 4.
or
If other riders are nearby, your next Click-to-Link call may randomly
connect to any of them.
scala rider® G9x / G9x PowerSet | 11
English
IMPORTANT: Three-Way Conference Mode Considerations
5.4 BUSY SIGNAL
When attempting to establish an Intercom call with another device
that is already busy, a “busy” signal will be heard. The scala rider is
busy while on a phone call, intercom call with Channels “A” and
“B”, “One+8” intercom call or Click-to-Link call.
5.5 RECEIVING INTERCOM CALLS
If a paired unit tries calling you via Intercom, the call will begin
almost instantly.
6. PAIRING AND USING A MOBILE PHONE,
GPS OR MP3 PLAYER
To use a Bluetooth device with your scala rider you must first pair
them. Once paired, they will automatically recognize each other
whenever they are within range (10m / 33ft).
Your unit has two Bluetooth channels for connection to mobile
phones, GPS devices and music players with A2DP.
6.1 PAIRING BLUETOOTH CHANNELS 1 AND 2
5.6 GROUP SIGNAL
Send an instant message to all paired scala rider G9 / G9x and
cardo SHO-1 units within a range of up to 350 m. The
recipients will hear a “Signal!” voice announcement. To reach a
maximum number of riders, the message is automatically
forwarded to all paired units within the recipient’s range. In this
manner the total range is extended to up to 1 km.
1. Make sure Bluetooth is enabled on your phone/GPS/MP3 player.
2. C
heck the unit is in Standby (single BLUE flash every 3 seconds).
3. To pair Bluetooth Channel 1 – press
for at least 5 seconds
until the RED and BLUE LEDs begin rapidly alternating.
To pair Bluetooth Channel 2 – press for at least 5 seconds
until the RED and BLUE LEDs begin rapidly alternating.
To pair a GPS, when LEDs begin rapidly alternating, tap
.
4. Search for Bluetooth devices on your phone/GPS/MP3 player by
following the device’s instructions.
5. After a few seconds the device will list “scala rider G9x”. Select it.
6. I f prompted for a PIN or Passkey, enter 0000 (four zeros).
7. T he device will confirm that pairing has succeeded and the LED
will begin flashing Blue, once every 3 seconds.
8. If pairing is not completed within 2 minutes, the unit will return
to Standby mode.
Send a Group Signal
Double tap
The transfer of wireless signals is subject to multiple external factors.
Therefore, users may use but should not rely on the Group Signal for
emergency purposes.
12
| scala rider® G9x / G9x PowerSet
IMPORTANT!
• If you have paired 2 different mobile phones directly to your
scala rider G9x, you will need to set one as default for making calls.
• I f your GPS supports it, you can pair the second mobile phone
directly to the GPS and then pair the GPS to your scala rider G9x,
and so connect both mobile phones and the GPS to your
scala rider G9x.
The scala rider G9x can also receive audio via the
enclosed cable from non-Bluetooth MP3 Players or
audio sources as described in section 6.5.
Available only on AVRCP compatible Bluetooth audio sources
Play
6.2 MAKING AND RECEIVING PHONE CALLS
Answer a call
6.3 LISTENING TO MUSIC VIA A2DP
Tap
or speak any word loudly to answer
by VOX
Reject a call
Remain silent for 15 seconds, or press
2 seconds
End a call
Tap
Voice Dial* (if supported
by mobile phone)
Tap
and follow the prompt from the
mobile
Redial*
Double-tap
Hot Dial†
Double-tap or tap
simultaneously
Set default mobile‡
While on a phone call, press
Change default mobile
In Standby, press
for
In standby, press
Pause/Stop Press
for 2 seconds or use Voice Command
for 2 seconds or use Voice Command
Next Track With music ON, press
for 2 seconds or use Voice Command
Previous
Track*
for 2 seconds or use Voice Command
With music ON, press
With music ON, press (scans up) or (scans down) for 5 sec.
Music Scan The first few seconds of each audio track will be played.
To stop the scan on the current track, say any word loudly into
Stop Scan the microphone or tap
*With some phones you may need to repeat this action
and
SWITCHING BETWEEN A2DP AUDIO SOURCES
and
for 5 seconds
for 5 seconds
INTERCOM CONFERENCE MODE
Add/Remove Channel “A” Tap
to/from a call
while on a phone call
Add/Remove Channel “B” Tap
to/from a call
while on a phone call
* This feature is not available during intercom or mobile calls
†B
efore using Hot-Dial, configure your Hot-Dial number via the Cardo Community.
‡ I f you have 2 mobile phones paired directly to your scala rider G9x, you will need
to set one of them to use as default for outgoing calls.
If a Music Player is paired, the scala rider G9x will use it as the
default A2DP audio source.
1. Stop the music playback from the current device.
2. Start music playback from the other device.
6.4 MUSIC SHARING
Music-sharing allows rider and passenger to listen to the
same music within a range of 33 ft / 10m.
Music sharing works only with A2DP (Bluetooth stereo)
enabled audio sources. In order to share your music with your
riding partner, your scala rider [SENDER] needs to be paired to the
other unit [RECEIVER] on CHANNEL A and the RECEIVER must be in
Standby mode.
scala rider® G9x / G9x PowerSet | 13
English
NOTES:
• Not all Bluetooth mobile phones can broadcast Bluetooth Stereo
music (A2DP), even if the phone has an MP3 player function.
Consult your mobile phone’s User Manual for more information.
• Not all Bluetooth GPS devices allow connection to Bluetooth audio
devices. Consult your GPS User Manual for more information.
• After pairing, you may need to tap
to connect.
[SENDER] Start/Stop
sharing your music:
During A2DP music playback, press
2 seconds
[RECEIVER] Stop music
sharing:
Press
for
for 2 seconds
Phone/Intercom calls and GPS audio navigation will override music
playback.
Music Sharing does not transmit voice audio and cannot be used as
an Intercom call.
6.5 LISTENING TO MUSIC VIA THE AUX
The USB / AUX jack can be used to connect a non-Bluetooth audio
source with a 3.5 mm / 1/8” stereo jack using the enclosed cable.
7. FM RADIO
Your scala rider G9x includes a built-in FM radio with a
6 Preset memory and RDS (Radio Data System).
RDS allows the radio to automatically retune to the
strongest frequency available for the FM station you
are listening to when the signal becomes too weak.
Radio On
In standby, press
Command
Radio Off
Press
Next Station
With radio ON, tap
for 2 seconds or use Voice
for 2 seconds or use Voice Command
or use Voice Command
Previous Station Use Voice Command
RDS ON/OFF
(Default: Off)
With Radio ON, press
2 seconds
and
simultaneously for
7.1 RADIO TUNING
AUX
1. Check that the scala rider is in Standby.
2. C
onnect the MP3 cable to the Music Player’s jack and insert the
other end of the cable into the USB/AUX jack.
To listen to music from a cable-connected device, operate the
Music Player using its buttons as usual (FF/REW/ PLAY/PAUSE).
14
| scala rider® G9x / G9x PowerSet
Preset stations can be saved via the Cardo Community or directly
from your scala rider G9x.
1. Turn on the Radio.
2. S elect a Preset number you wish to set (Preset 1 – 6) by tapping
until the desired preset is heard.
3. F ind an FM station to save using Seek or Scan (see 7.1).
Seek and Save: (Find the next FM station)
1. Press or for 2 seconds.
• searches upwards (higher frequency) for a station
• searches downwards (lower frequency) for a station
2. Tap within 20 seconds of finding the FM station to save it as
the current Preset.
During Scan, tap
current Preset
to fast save the current FM station as the
7.2 AUTOMATIC RADIO TUNING
Find new stations fast and easy by automatically creating a list of
6 temporary radio stations.
1. With the radio on, press for 5 seconds.
2. T he radio will search upwards (higher frequency) from the
current station and store the next 6 FM stations it discovers.
3. I f desired, repeat to store the next 6 FM stations.
These 6 temporary stations cannot be saved and do not replace the
FM Presets you may have saved.
8. TROUBLESHOOTING
Reboot
If your scala rider stops responding, reset it by turning it
off and then on again (press
for 2 seconds).
or for 5 secs until LED flashes
Reset Pairing 1. In Standby, press
RED/BLUE.
(Deletes all
paired devices) 2. Press for 2 seconds until LED flashes 5 times in
PURPLE.
9. SUPPORT
For additional information:
 www.cardosystems.com
 support@cardosystems.com
SA and Canada: 1-800-488-0363
 UInternational:
+49 89 450 36819
IMPORTANT
MULTINATIONAL COMMERCE COMPANIES AND ONLINE AUCTION WEBSITES ARE NOT AUTHORIZED
TO SELL CARDO PRODUCTS AND PURCHASES FROM SUCH SITES ARE AT YOUR OWN RISK. TO RECEIVE
WARRANTY OR CUSTOMER SERVICE, YOU MUST SUBMIT ORIGINAL RECEIPTS FROM AUTHORIZED
CARDO DEALERS.
PRODUCTS THAT WERE IMPORTED FROM NORTH AMERICA MUST BE SERVICED IN THE USA.
Turning off your scala rider will clear the temporary stations and
restore the FM Presets.
scala rider® G9x / G9x PowerSet | 15
English
Scan and Save: Scan through FM stations
1. Press for 5 seconds. The radio will search upwards (higher
frequency) for a station. When a station is found, it can be heard
for a few seconds.
2. T o stop the scan on this station: Tap .
3. Tap within 20 seconds of finding the FM station to save it as
the current Preset.
4. To continue scan: Wait for the next station to be found.
10. NOTICES
Federal Communications Commission (FCC) Statement
European CE Notice 
15.21
Your Cardo product (the “Product”) is in conformity with the following essential requirements of
Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3.1a, 3.1.b and 3.2. The Product is
manufactured in accordance with Annex II of the above directive.
You are cautioned that changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired
operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance.
The antenna used for this transmitter must not transmit simultaneously with any other antenna or
transmitter, except in accordance with FCC/IC multi-transmitter product procedures.
Industry Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired
operation of the device.
16
IC RF Radiation Exposure Statement:
This equipment complies with the RSS-102 exemption from routine RF exposure evaluation for use in
an uncontrolled environment.
| scala rider® G9x / G9x PowerSet
Declaration of Conformity (DOC)
The Product is compliant with and adopts the Bluetooth® Specification 3.0. Class 1 + EDR and has
successfully passed all interoperability tests that are specified in the Bluetooth® specification. However,
interoperability between the device and other Bluetooth®-enabled products is not guaranteed.
Copyright
The contents of this User Guide, including all text, illustrations and drawings are the exclusive
intellectual property of Cardo Systems, Inc. (the “Company”) and are protected by copyright laws.
They are not in the public domain. Any partial or total reproduction, translation and or dissemination,
without the prior written authorization by the Company are strictly prohibited. Any rights not
expressly granted herein are reserved.
IMPORTANT SAFETY AND WARRANTY INFORMATION –
WAIVER AND GENERAL RELEASE
WARNING:
Cardo Systems Inc., (“Cardo” or the “Company”) notifies you that your complete and undivided
attention is required when using a communication device (the “Product”) while riding. Failure to
avoid potentially hazardous situations could result in accident resulting in serious injury or death.
Cardo advises you to take all necessary precautions and remain alert to the traffic, weather and all
road conditions. It is best to stop away from traffic prior to activating or deactivating the Product or
initiating or receiving any calls.
Do not perform pairing, linking or similar operations while riding. All publications are intended to
address technical capabilities and should not be construed as encouraging the operation of Cardo’s
Products in any manner that is unsafe or prohibited by law.
Exercise all due caution while using this Product and obey all applicable traffic laws. Always ride and
use the Product in a safe manner. Do not become distracted by the Product while riding on a vehicle.
When riding, always consider road, traffic, terrain and other conditions to maximize safety. Do not
operate the Product if it becomes unsafe to do so.
In some regions or states, the use of mobile communications systems is prohibited or restricted.
Check all laws and regulations that apply to your region before using the Product and be mindful that
compliance with all laws and regulations is the user’s responsibility. Use the Product in motion only
where and in the manner that such devices are permitted by applicable law. The Product should not
No part of the body should come in contact with the antenna during operation of the equipment. Use
Product only where safe, and avoid usage at gas stations, fuel depots or around explosives. Use with
hearing aids and medical devices only after consulting a physician or specialist. Make sure to install and
mount the Product in a stable manner.
HEALTH WARNINGS:
The warranties and remedies contained herein are exclusive and in lieu of all other warranties express,
implied or statutory, including any liability arising under any warranty of merchantibility or fitness
for a particular purpose, statutory or otherwise that Cardo specifically disclaims. This warranty gives
you specific legal rights which may vary from state to state or from jurisdiction to jurisdiction. Cardo
makes no other warranties express or implied beyond those stated specifically herein. This warranty
is extended by Cardo solely to the original purchaser and is not assignable or transferable to others.
Cardo assumes no obligation or liability for additions or modifications to this warranty unless made in
writing and signed by an officer of the company.
Hearing Loss
Batteries are warranted only if the battery capacity falls below 50% of rated capacity or if the battery
develops leakage.
Audio devices can cause hearing loss. Employ care and avoid exposure to excessive volume levels that
may damage or impair hearing or lead to hearing loss. Permanent hearing loss may occur if Products
are used at high volume for prolonged periods of time.
IMPORTANT: Do not store your Product without charging it from time to time for periods in excess
of six months, as this may cause irreversible damage to the capacity of your battery.
Your warranty will not cover such events.
RF Signals
This warranty also becomes void if:
Most electronic equipment is shielded from RF signals. However, certain electronic equipment may
not be shielded against the RF signals emanating from your wireless equipment.
a. any of the seals on the case or battery are broken or Product or battery show signs of tampering,
Pacemakers
c. the Product is used in contravention of its intended purpose
The Health Industry Manufacturers Association recommends that a minimum separation of about
six inches (or 16 cm) to be maintained between a mobile phone or wireless device and a pacemaker
to avoid potential interference with the pacemaker. Be sure not to interfere with the functionality of
personal medical devices.
d. the Product was purchased from online auctions
Hearing Aids
Some devices may interfere with certain hearing aids. In the event of such interference, you should
consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your device and/ or your
physician to determine if it is adequately shielded from interference caused by external RF energy.
Your physician may be able to assist you in obtaining this information.
LIMITED WARRANTY
Subject to the applicable laws and regulations in your jurisdiction, your Product is covered by a TwoYear Limited product warranty from the date of original purchase. Please retain the retail sales receipt
and your registration data for proof of purchase.
Subject to the aforementioned, Cardo hereby represents that this Product is warranted to be free from
defects in materials or workmanship (proof of purchase and registration required). Within the subject
period, Cardo will, at its sole option, repair or replace any components that fail in normal use. Such
repairs or replacements will be made at no charge to the customer for parts or labor, provided that the
customer shall be responsible for any shipping cost. This warranty does not cover failures due to abuse,
misuse, accident or unauthorized alteration or repairs.
This Product is intended to be used only as a communication and entertainment device and should not
be used in any location or jurisdiction where its use is prohibited.
b. t he battery is used in equipment other than the equipment for which it was intended.
Cardo assumes no responsibility resulting from the use of non-Cardo components or products in
conjunction with its Products, and specifically the use of third party chargers or Bluetooth® devices.
Furthermore, Cardo is not responsible for any damage to any part of the Product resulting from the
use of ancillary equipment not furnished by Cardo which is attached to or used in connection with
the Product.
Not covered by the warranty:
1. Defects or damage resulting from the use of this Product in other than its normal and customary
manner.
2. Defects or damage from misuse, accident or neglect.
3. Defects caused by improper operation, maintenance, installation, adjustment or modification of
any kind (incl. long-term storage without periodic charging of the battery).
4. Products opened, disassembled or repaired by non-authorized parties.
5. Defects or damage due to exposure to excessive temperatures, adverse weather conditions,
external impacts or spills of food or liquid.
6. All plastic surfaces and all other externally exposed parts that are scratched or damaged after
purchase.
Disclaimer of Warranty
The device and its accessories are provided “as is” and “as available” without warranty of any
kind beyond those assumed in the enclosed manual.
scala rider® G9x / G9x PowerSet | 17
English
be used in contravention of local, state or federal laws and regulations. Please check federal, state and
local laws and regulations before using your Cardo Product.
LIMITATION OF LIABILITY
WAIVER AND GENERAL RELEASE
In no event shall Cardo be liable for any incidental, special, indirect, punitive, exemplary or
consequential damages, whether resulting from the use, misuse, or inability to use this product or
from defects in the product, or for any damages whatsoever resulting from the use of the product,
whether based on breach of contract, tort (including negligence), product liability or otherwise
even if advised of the possibility of such damages. You acknowledge and agree that the limitations
set forth above are fundamental elements of this agreement to which you consent and without
which the product would not be provided to you absent such limitations. Some states do not allow
certain exclusions of incidental or consequential damages, so the above limitations may not apply
to you.
By using the Product, you will waive substantial legal rights including the right to sue. Please read the
following carefully before using the Product.
Cardo retains the exclusive right to repair or replace (with a new or newly-refurbished
replacement Product) the device or software or give a refund of the purchase price at its sole
discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF
WARRANTY.
Warranty Service
To obtain warranty service, your Product must be registered. Register online at:
www.cardosystems.com/registration. Please present the Product, along with your registration
number, bill of sale (receipt) at any authorized Service Center or at the store from which you have
purchased the Product.
To obtain warranty service, contact Cardo’s product support and obtain an RMA tracking number, or
contact your local Cardo authorized dealer. Ship securely with a copy of the original sales receipt
which is required as proof of purchase for warranty repairs. The RMA tracking number should be
written on the outside of the package. Send the Product freight charges prepaid, to the Cardo address
as directed by Cardo.
Online Auction Purchases: Online auction confirmations are not accepted for warranty verification. To
obtain warranty service, an original or copy of the sales receipt from the original retailer is required.
Cardo will not replace missing components from online auction sites.
Other manufacturers: Cardo is not responsible for and expressly disclaims any responsibility for how
Cardo Products are used or misused arising out of use with products, services or information of other
vendors.
By using the Product, you are irrevocably releasing, indemnifying from any liability, loss, claim and
expense (including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or death
as well as losses or damages in goods, to any vehicles including your own, or to any property or asset
that belong to you or to third parties, any of which may result from using the Product under any
circumstances or conditions and irrespective of jurisdiction.
1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever release,
discharge, indemnify and hold harmless Cardo from any and all litigation, claims, debts, demands,
actions and liability which may arise, directly or indirectly, from using the Product for any distress, pain,
suffering, discomfort, loss, injury, death, damages to or in respect to any person or property however
caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to
you on some future date as a result of said use, to the fullest extent permitted by law.
2. You fully understand and assume the risks in using the Product, including risk of negligent acts or
omissions by others. All risks for operating the Product are assumed solely by the user of the Product.
3. You confirm that you are physically capable to use the Product and that you have no medical conditions
or needs that may infringe upon your abilities to do so in a safe manner. You further confirm that you
will not consume any alcohol that may affect your alertness or any mind-altering substance, and will
not carry, use or consume these substances before or during the use of the Product.
4. You fully acknowledge our warnings and understand that:
(a) r isks exist in using the Product while in traffic, including but not limited to injury or illness, strains,
fractures, partial and/or total paralysis, death or other ailments that could cause serious disability;
(b) these risks may be caused by the negligence of the manufacturers or its agents or any third party
involved in the Product;
(c) these risks and dangers may arise from foreseeable or unforeseeable causes.
You hereby assume all risks and dangers and all responsibility for any losses and/or damages, whether
caused in whole or in part by the negligence or other conduct of others, including Cardo.
5. By using the Product, you confirm that you have read this release of liability and fully understand
and accept its terms and conditions.
www.cardosystems.com
18
| scala rider® G9x / G9x PowerSet
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising