MILLI EDGE MK2

WALL BASIN MIXER SET 200MM

200

120

220

200

5

47 - 67

ADJUSTMENT page 1 of 2

60 25

3.5°

40 14

35 4

SPECIFICATIONS

Recommended Use

Finish Available

Pressure Rating

Temperature Rating

Suitable Hot Water

WELS

Standards

Domestic, hotel and commercial

Chrome

Maximum continuous operating pressure 500 kPa.

Note: For best performance and longer life, we recommend 150-500 kPa.

Maximum continuous working temperature 75 o C

Storage Tank: Yes

Continuous Flow: Refer to manufacturer of continuous hot water systems

Gravity Feed: No

Stars: 5

Flow Rate: 6lt/min

AS/NZS 3718

CLEANING RECOMMENDATIONS

We recommend the use of soapy water or approved cleaners.

This product should not be cleaned with abrasive materials.

Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions.

To see the complete MILLI EDGE range go to www.reece.com.au/bathrooms

The more water efficient

WATER RATING www.waterrating.gov.au

6.0

litres per minute

In accordance with AS/NZS 6400

Licence No. 0133

Phoenix Industries Pty Ltd

AS/NZS 3718

WM-025901

Disclaimer: listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.

Tech Page Version 1

MILLI EDGE MK2

WALL BASIN MIXER SET 200MM

page 2 of 2

INSTALLATION INSTRUCTIONS

Important Note

Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. Your mixer comes to you already factory assembled and tested. We do not recommend the dismantling of any internal part of the mixer. The mixers are factory tested and sealed so as to give the best performance.

INSTALLATION INSTRUCTIONS

WALL MIXER SET

IN0283 REV A

Screw the Mixer Breach onto Noggin.

Ensure that the Outlet and Mixer Body centres are level.

Noggin

Connect hot and cold water supply, as shown.

Test and check for leaks.

Hot

Check centre distance of the breach assembly for

120mm or 140mm size.

Mark centre line according to measured result.

Create a 25mm hole and a 45mm hole on the cement sheet and tiles, as shown.

Centre Distance : 120mm or 140mm

Grub Screw

Screw Cap

Handle

Check le vel

Cold

25mm

45mm

Do not remove the protective cover until final fit-off.

Centre Distance of Breach

Noggin

45mm to 65mm

Adjustment recommended working pressure maximum hot water temperature

Remove the protective cover from the mixer.

Apply Teflon tape to Elbow Thread.

Gently push the dress plate into position.

Screw Spout Adaptor to Elbow Thread with a spanner or Allen Key.

Adjustment range from the finished face of the tiles to the noggin is

45mm to 65mm, as shown.

Spout Adaptor

Teflon Tape

Elbow

Push Wall Outlet to the spout adaptor and fasten

Grub Screws to secure Wall Outlet.

Fit Mixer Handle into position and tighten Grub

Screw to secure handle.

Fit Screw Cap into position.

Wall Outlet

Dress Plate

Grub Screw

Screw Cap

Mixer Handle

NOTE:

- If the pressure exceeds or is likely to exceed 550kpa,

an approved pressure limiting device must be installed.

- Flush out all pipe work prior to installation.

- If the water temperature exceeds 75°C, an approved

tempering valve must be fitted.

- Installation should comply with Australian standard

AS3500.1 or relevant local authority requirements.

Showers may not be suitable for use within:

• Gravity-fed water systems

• Some instantaneous hot water systems; or

• Pressure supply less than 150kPa;

NOTE:The 500kPa maximum water supply pressure does not apply to fire service outlets.

Failure to comply with the above may void all warranties.

WARRANTY:

Please refer to the full warranty statement enclosed with the product before installing.

MAINTENANCE AND CARE:

- Products should be cleaned with mild

liquid detergent or soap and water.

- Do not use cream cleaners or citrus

based cleaning products, as they are

abrasive.

- Use of unsuitable cleaning agents may

damage the surface. Any damage caused

in this way will not be covered by

warranty.

DISCLAIMER:

While we aim to ensure the specifications shown are correct at the time of printing, we reserve the right to make modifications without prior notice. Always use the physical product measurements for mark-ups and roughing-in as the line drawing shown may differ from the actual product over time.

*All measurements are shown in millimeters.

Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference