METHVEN
AIO AURAJET RAIL SHOWER
198
216
Typical page 1 of 3
46
107
Variable
SPECIFICATIONS
Recommended Use
Colour
Pressure Rating
Temperature Rating
Suitable Hot Water
Units
WELS
Standards
Spray Patterns
Domestic, hotel and commercial
Matte Black
Suitable for high pressure applications and has been WELS certified to the following:
Minimum operating pressure 150kPa
Maximum operating pressure 500kPa
Maximum continuous working temperature 70°C
(recommended 38°C - 42°C)
Minimum 1°C
Storage Tank: Yes
Continuous Flow: Yes
Gravity Feed: Not recommended
Stars: 3
Flow rate: 9L/min
AS/NZS 3662
Aurajet Spray
To see the complete AIO range go to www.reece.com.au/bathrooms
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by improper treatment is not covered by the product warranty – refer to warranty conditions.
The more stars the more water efficient
WATER RATING www.waterrating.gov.au
9.0
litres per minute
In accordance with AS/NZS 6400
Licence No. 0095
Methven Australia Pty Ltd
WaterMark
AS/NZS 3662
WMKT21090
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 1
page 2 of 3
METHVEN
AIO AURAJET RAIL SHOWER
INSTALLATION INSTRUCTIONS
Step 1
• Mount the wall boss housings in desired position with the screws.
Check the mounts are vertically aligned. Ensure the grub screws are located on the correct sides as shown.
Grub Screw
Topside
Protection
Pad
Grub Screw
Underside
Step 2
• Slide soap dish onto the rail
FLOOR
Step 3
• Fit the internal mounting brackets by locating in slot and rotating 90°.
Step 4
• Tighten the tensioning screws lightly with the hex key provided.
Rail can be oriented so that handset sits on opposite side of rail .
Step 5
• Match the mounting brackets to wall bosses and push into place.
• Slide rail up or down to centralise the brackets
• Remove the rail and tightenthe tensioning screws firmly.
• Relocate the rail onto wall bosses and tighten grub screws top and bottom.
Step 6
• To adjust slider position, rotate the slider handle to unlock and lock the slider as shown.
Unlock
Lock
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
page 3 of 3
METHVEN
AIO AURAJET RAIL SHOWER
INSTALLATION INSTRUCTIONS
Elbow Installation:
Step 1
• Wall lining hole should be cut or finished as per the dimension shown in the diagram on the right
• Cut off the threaded nipple 13±2mm from the wall lining and apply thread seal tape to ensure a good seal.
Step 2
• Screw the elbow onto the nipple ensuring that the o-ring is sufficiently compressed to create a watertight seal.
• Ensure that the elbow is oriented vertically with the outlet oriented downwards.
13±2m m
26mm max
Step 3
• Connect hose to elbow and handset
• Ensure swivelling cone is connected to the handset
Handset
Flat
Washer
Swivelling
Cone
Care and Cleaning
We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials.
Damage caused by improper treatment is not covered by the product warranty – refer to warranty conditions on the last page.
A filter washer should be installed in the hose cone on the water outlet and it should be cleaned periodically.
If shower performance is compromised by the build-up of lime-scale, clean by using a soft toothbrush and gently scrubbing along the spray slot under running water.
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
