Allen-Bradley 1606-XLC, 1606-XLE480FP Reference Manual

Reference Manual
Bulletin 1606 Switched Mode Power Supplies
Catalog Number: 1606-XLE480FP
Index
Page
1. Intended Use .......................................................3
2. Installation Requirements ...................................3
3. AC-Input...............................................................4
4. DC-Input...............................................................5
5. Input Inrush Current ...........................................5
6. Output .................................................................6
7. Hold-up Time.......................................................8
8. DC-OK Relay Contact ..........................................8
9. Efficiency and Power Losses................................9
10. Lifetime Expectancy and MTBF.........................10
11. Functional Diagram...........................................10
12. Terminals and Wiring........................................11
13. Front Side and User Elements...........................12
14. EMC....................................................................13
15. Environment ......................................................14
16. Protection Features ...........................................15
17. Safety Features ..................................................15
18. Dielectric Strength ............................................16
19. Certifications......................................................16
Page
20. Physical Dimensions and Weight ..................... 17
21. Accessories ........................................................ 18
21.1. 1606-XLC Wall Mounting Bracket......... ...18
22. Application Notes............................................. 19
22.1. Peak Current Capability ...........................19
22.2. Back-feeding Loads ..................................19
22.3. External Input Protection .........................20
22.4. Output Circuit Breakers ............................20
22.5. Parallel Use to Increase Output Power ....21
22.6. Parallel Use for Redundancy ....................21
22.7. Series Operation .......................................22
22.8. Inductive and Capacitive Loads ................22
22.9. Charging Batteries ....................................23
22.10. Operation on Two Phases ........................23
22.11. Use in a Tightly Sealed Enclosure ............23
22.12. Mounting Orientations ............................24
Terminology and Abbreviations
•
•
•
•
•
•
•
•
•
PE and symbol—PE is the abbreviation for Protective Earth and has the same meaning as the symbol .
Earth, Ground—This document uses the term “earth” which is the same as the U.S. term “ground”.
T.b.d.—To be defined, value or description will follow later.
3AC 400V—A figure displayed with the AC or DC before the value represents a nominal voltage with standard tolerances (usually ±15%)
included. E.g.: DC 12V describes a 12V battery whether it is charged (13.7V) or discharged (10V).
230Vac—Afigure with the unit (Vac) at the end is a momentary figure without any additional tolerance included.
50Hz vs. 60Hz—Unless otherwise stated, AC 230V parameters are valid at 50Hz mains frequency.
may—A key word indicating flexibility of choice with no implied preference.
shall—A key word indicating a mandatory requirement.
should—A key word indicating flexibility of choice with a strongly preferred implementation.
Bulletin 1606 Switched Mode Power Supplies
Power Supply
AC 100-240V Wide-range Input
Width only 65mm
Efficiency up to 93.9%
ATEX and IECEx Approved
Excellent Partial Load Efficiency
20% Output Power Reserves
Safe HiccupPLUS Overload Mode
Easy Fuse Tripping due to High Overload Current
(typ. 45A for 15ms)
Active Power Factor Correction (PFC)
Minimal Inrush Current Surge
Full Power Between -25°C and +60°C
DC-OK Relay Contact
Current Sharing Feature for Parallel Use
3 Year Warranty
Description
Specification Quick Reference
The 1606-XLE are cost optimized power supplies
without compromising quality, reliability and
performance. The 1606-XLE series is part of Rockwell
Automation's family of power supplies. The most
outstanding features of the 1606-XLE480FP are its high
efficiency, electronic inrush current limitation, active
PFC and wide operational temperature range.
Output voltage
Adjustment range
Output current
This series includes all the essential basic functions.
The devices include a power reserve of 20%, which
may even be used continuously at temperatures
up to +45°C. Additionally, the 1606-XLE480FP can
deliver about 4 times the nominal output current for
15ms which helps to trip fuses on faulty output branches.
High immunity to transients and power surges as well as
low electromagnetic emission, a DC-OK relay contact
and a large international approval package for a variety
of applications make this unit suitable for nearly every
situation.
DC 48V
48 - 56V
10A
12A
8.6A
10.3A
480W
Output power
576W
< 50mVpp
Output ripple
AC 100-240V
AC Input voltage
50-60Hz
Mains frequency
4.36 / 2.33A
AC Input current
0.99 / 0.95
Power factor
typ. 9 / 7A peak
AC Inrush current
92.6 / 93.9%
Efficiency
38.4 / 31.2W
Losses
Temperature range -25°C to +70°C
Derating *)
12W/°C
Hold-up time
typ. 26 / 26ms
Dimensions
65x124x127mm
Weight
1000g / 2.2lb
at 48V, amb <60°C
at 48V, amb <45°C
at 56V, amb <60°C
at 56V, amb <45°C
ambient <60°C
ambient <45°C
20Hz to 20MHz
-15%/+10%
±6%
at 120 / 230Vac
at 120 / 230Vac
at 120 / 230Vac
at 120 / 230Vac
at 120 / 230Vac
operational
+60 to +70°C
at 120 / 230Vac
WxHxD
*) between 100-85Vac, see section 15.
Catalog Numbers
Power Supply 1606-XLE480FP 48-56V Standard unit
Wall mount bracket
1606-XLC
Accessory
Certification Marks
IND. CONT. EQ.
UL 508
Class I Div 2
2
UL 60950-1
IECEx
Marine, pending
ATEX
II 3G Ex nA nC II T3 Gc
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
EMC, LVD, RoHS
Bulletin 1606 Switched Mode Power Supplies
Intended Use
• This device is designed for installation in an enclosure and is intended for the general professional use such as in industrial control, office,
communication, and instrumentation equipment.
• Do not use this power supply in aircraft, trains, nuclear equipment or similar systems where malfunction may cause severe personal injury or
threaten human life.
• This device is designed for use in hazardous, non-hazardous, ordinary or unclassified locations.
Installation Requirements
•
•
•
•
This device may only be installed and put into operation by qualified personnel.
This device does not contain serviceable parts. The tripping of an internal fuse is caused by an internal defect.
Should damage or malfunction occur during installation or operation, immediately turn power off and send unit to the factory for inspection.
Mount the unit on a DIN rail so that the terminals are located on the bottom of the unit. For other mounting orientations, see derating
requirements in this document. Please refer to section 24.13.
• This device is designed for convection cooling and does not require an external fan. Do not obstruct airflow and do not cover ventilation grid
(e.g. cable conduits) by more than 30%!
• Keep the following installation clearances: 40mm on top, 20mm on the bottom, 5mm on the left and right sides are recommended when the
device is loaded permanently with more than 50% of the rated power. Increase this clearance to 15mm in case the adjacent device is a heat
source (e.g. another power supply).
• A disconnecting mechanism shall be provided for the output of power supplies when used in applications according to CSA C22.2 No. 107.1.-01.
-
SHOCK HAZARD: Do not use the power supply without proper grounding (Protective Earth). Use the terminal on the input
block for earth connection and not one of the screws on the housing.
Turn power off before working on the device. Protect against inadvertent re-powering
Make sure that the wiring is correct by following all local and national codes
Do not modify or repair the unit
Do not open the unit as high voltages are present inside
Use caution to prevent any foreign objects from entering the housing
Do not use in wet locations or in areas where moisture or condensation can be expected
Do not touch during power-on, and immediately after power-off. Hot surfaces may cause burns.
WARNING: EXPLOSION HAZARDS!
Substitution of components may impair suitability for this environment. Do not disconnect the unit or operate the voltage adjustment or S/P jumper unless
power has been switched off or the area is known to be non-hazardous.
Notes for use in hazardous location areas:
• The unit is suitable for use in Class I Division 2 Groups A, B, C, D locations
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
3
Bulletin 1606 Switched Mode Power Supplies
3. AC-Input
AC input
AC input range
Allowed voltage L or N to earth
Input frequency
Turn-on voltage
Shut-down voltage
Input current
Power factor*)
Crest factor**)
Start-up delay
Rise time
Turn-on overshoot
nom.
min.
min.
AC 100-240V
100-264Vac
85-100Vac
min.
max.
nom.
typ.
typ.
typ.
typ.
264-300Vac
300Vac
50–60Hz
84Vac
39Vac
53Vac
74Vac
suitable for TN-, TT- and IT mains networks
continuous operation
short term or with output derating (1%/V) or with
reduced ambient temperature, see Fig. 15-1,
no damage between 0 and 100Vac
< 500ms
continuous, IEC 62103
±6%
steady-state value, see Fig. 3-1
steady-state value at 2.5A load, see Fig. 3-1
steady-state value at 5A load, see Fig. 3-1
steady-state value at 10A load, see Fig. 3-1
typ.
typ.
typ.
typ.
typ.
AC 100V
5.25A
0.99
1.5
850ms
90ms
AC 120V
4.36A
0.99
1.5
850ms
90ms
AC 230V
2.33A
0.95
1.65
650ms
90ms
typ.
230ms
230ms
230ms
max.
200mV
200mV
200mV
at 48V, 10A, see Fig. 3-3
at 48V, 10A, see Fig. 3-4
at 48V, 10A
see Fig. 3-2
at 48V, 10A const. current load,
0mF load capacitance, see Fig. 3-2
at 48V, 10A const. current load,
10mF load capacitance, see Fig. 3-2
see Fig. 3-2
*) The power factor is the ratio of the true (or real) power to the apparent power in an AC circuit.
**) The crest factor is the mathematical ratio of the peak value to RMS value of the input current waveform.
Fig. 3-1 Input voltage range
Turn-on
Shut-down
max.
500ms
Input
Voltage
VIN
85V
Start-up
delay
Rise
Time
264V 300Vac
Fig. 3-3 Input current vs. output load at 48V
Fig. 3-4 Power factor vs. output load
Power Factor, typ.
Input Current, typ.
6A
c
Va
100 ac
V
120
5
4
100Vac, 120Vac
1.0
230Vac
0.95
0.9
3
ac
230V
2
0.85
0.8
1
Output Current
0
Output Current
0.75
1
4
- 5%
Output
Voltage
Overshoot
Rated
input range
POUT
Fig. 3-2 Turn-on behavior, definitions
2
3
4
5
6
7
8
9 10 11 12A
1
2
3
4
5
6
7
8
9
10 11 12A
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
4. DC-Input
Do not operate this power supply with DC-input voltage. Use the 1606-XLE480FP-D instead.
5. Input Inrush Current
An active inrush limitation circuit limits the input inrush current after turn-on of the input voltage and after short
input voltage interruptions.
The charging current into EMI suppression capacitors is disregarded in the first microseconds after switch-on.
*)
Inrush current
max.
typ.
max.
typ.
Inrush energy*)
Inrush delay
*)
AC 100V
13Apeak
11Apeak
2A2s
940ms
AC 120V
13Apeak
9Apeak
2.5A2s
940ms
AC 230V
13Apeak
7Apeak
0.5A2s
740ms
temperature independent
temperature independent
temperature independent
start-up delay plus rise time
Mains interruptions > 500ms
Fig. 5-1 Typical input inrush current
behavior at nominal load and 25°C ambient
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
5
Bulletin 1606 Switched Mode Power Supplies
6. Output
Output voltage
Adjustment range
nom.
min.
max.
typ.
typ.
typ.
max.
max.
48V
48-56V
60V****)
48.0V
46.0V
48.0V
10mV
150mV
typ.
2000mV
Ripple and noise voltage
Output current
max.
nom.
nom.
nom.
nom.
typ.
50mVpp
10A
12A*)
8.6A
10.3A*)
40A
Output power
nom.
nom.
min.
max.
max.
480W
576W*)
cont. current
HiccupPLUS mode**)
18A***)
22A***)
7A***)
min.
typ.
typ.
40A
50A
2 450μF
Factory settings
Line regulation
Load regulation
Overload behaviour
Short-circuit current
Output capacitance
guaranteed
at clockwise end position of potentiometer
±0.2%, at full load, cold unit, in “single use” mode
±0.2%, at full load, cold unit, in “parallel use” mode
at no load, cold unit, in “parallel use” mode
85-300Vac
in “single use” mode: static value, 0A 10A;
see Fig. 6-1
in “parallel use” mode: static value, 0A 10A,
see Fig. 6-2
20Hz to 20MHz, 50Ohm
at 48V, ambient temperature <60°C, see Fig. 6-1
at 48V, ambient temperature <45°C, see Fig. 6-1
at 56V, ambient temperature <60°C, see Fig. 6-1
at 56V, ambient temperature <45°C, see Fig. 6-1
up to 15ms,output voltage stays above 40V, see Fig.
6-4. This peak current is available once every five
seconds. See section 22.1 for more peak current
measurements.
continuously available
Power Boost*)
output voltage >25Vdc, see Fig. 6-1
output voltage <25Vdc, see Fig. 6-1
load impedance <10mOhm, see Fig. 6-3
load impedance <10mOhm, see Fig. 6-3
average (R.M.S.) current, load impedance 100mOhm,
see Fig. 6-3
up to15ms, load impedance <10mOhm, see Fig. 6-4
up to15ms, load impedance <10mOhm, see Fig. 6-4
included inside the power supply
*)
Power Boost
This power/ current is continuously allowed up to an ambient temperature of 45°C. Above 45°C, do not use this power/ current longer
than a duty cycle of 10% and/ or not longer than 1 minute every 10 minutes.
**)
HiccupPLUS Mode
At heavy overloads (when output voltage falls below 25V), the power supply delivers continuous output current for 2s. After this, the
output is switched off for approx. 18s before a new start attempt is automatically performed. This cycle is repeated as long as the
overload exists. If the overload has been cleared, the device will operate normally. See Fig. 6-3.
***) Discharge current of output capacitors is not included.
****) This is the maximum output voltage which can occur at the clockwise end position of the potentiometer due to tolerances. There is no
guarantee that this value can be achieved. The typical value is about 57.0V (in “single use” mode).
6
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
Fig. 6-2 Output voltage in “parallel use”
mode, typ.
Fig. 6-1 Output voltage vs. output current,
typ.
Output Voltage (Single Use, typ.)
56V
Factory
setting
32
Adjustment
Range
56V
Continuous
current
48
40
Output Voltage (Parallel Use, typ.)
Adjustment
Range
54V
52V
50V
48V
24
Hiccup
mode
16
8
0
44V
42V
Output Current
0
2.5
5
Factory
setting
46V
7.5 10 12.5 15 17.5 20A
Output Current
0
Fig. 6-3 Short-circuit on output, HiccupPLUS mode, typ.
2
4
6
8
10
12A
Fig. 6-4 Dynamic overcurrent capability, typ.
Output Voltage (dynamic behavior, < 15ms)
56V
Output
Current
Normal
operation
Normal
operation
Short -circuit
20A
48
Adjustment
Range
40
32
24
t
0
2s
18s
2s
18s
2s
18s
16
8
0
Output Current
0
5 10 15 20 25 30 35 40 45 50A
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
7
Bulletin 1606 Switched Mode Power Supplies
7. Hold-up Time
Hold-up Time
AC 100V
65ms
54ms
26ms
21ms
typ.
min.
typ.
min.
Fig. 7-1 Hold-up time vs. input voltage
AC 120V
65ms
54ms
26ms
21ms
AC 230V
65ms
54ms
26ms
21ms
at 48V, 5A, see Fig. 7-1
at 48V, 5A, see Fig. 7-1
at 48V, 10A, see Fig. 7-1
at 48V, 10A, see Fig. 7-1
Fig. 7-2 Shut-down behavior, definitions
Hold-up Time
Zero Transition
80ms
70
60
50
40
30
20
10
0
48V, 5A, typ.
48V, 5A, min.
48V, 10A, typ.
48V, 10A, min.
120
155
190
- 5%
Output
Voltage
Hold-up Time
Input Voltage
90
Input
Voltage
230Vac
8. DC-OK Relay Contact
This feature monitors the output voltage, which is produced by the power supply itself. It is independent of a back-fed
voltage from a unit connected in parallel to the power supply output.
Contact closes
Contact opens
As soon as the output voltage reaches 90% of the adjusted output voltage level.
As soon as the output voltage dips more than 10% below the adjusted output voltage.
Short dips will be extended to a signal length of 100ms. Dips shorter than 1ms will be ignored.
max.
60Vdc 0.3A, 30Vdc 1A, 30Vac 0.5A
resistive load
min.
1mA at 5Vdc
min. permissible load
See dielectric strength table in section 18.
Contact ratings
Isolation voltage
Fig. 8-1 DC-ok relay contact behavior
VOUT = VADJ
10%
<
1ms
open
8
>
1ms
closed
0.9* VADJ
100ms
open
closed
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
9. Efficiency and Power Losses
Efficiency
Average efficiency*)
Power losses
*)
typ.
typ.
typ.
AC 100V
92.0%
91.8%
91.1%
AC 120V
92.6%
92.3%
91.7%
AC 230V
93.9%
93.9%
92.8%
typ.
typ.
typ.
typ.
6.1W
22.5W
41.7W
51.5W
3.6W
21.6W
38.4W
48.0W
2.4W
18.3W
31.2W
37.4W
at 48V, 10A
at 48V, 12A (Power Boost)
25% at 2.5A, 25% at 5A,
25% at 7.5A. 25% at 10A
at 48V, 0A
at 48V, 5A
at 48V, 10A
at 48V, 12A (Power Boost)
The average efficiency is an assumption for a typical application where the power supply is loaded with 25% of the nominal load for 25%
of the time, 50% of the nominal load for another 25% of the time, 75% of the nominal load for another 25% of the time and with 100%
of the nominal load for the rest of the time.
Fig. 9-1
Fig. 9-2
Efficiency vs. output current at 48V,
typ
Efficiency
Losses vs. output current at 48V, typ.
Power Losses
96%
60W
94
c
b
a
92
90
a) 100Vac
b) 120Vac
c) 230Vac
88
86
Output Current
84
0
Fig. 9-3
1 2
3
4 5
6
7
8
40
20
10
Output Current
0
0
Fig. 9-4
1 2
3
4 5
6
7
8
9 10 11 12A
Losses vs. input voltage at 48V, 10A,
typ.
Efficiency
Power Losses
95%
50W
94
45
93
40
92
35
91
30
90
c
30
9 10 11 12A
Efficiency vs. input voltage at 48V,
10A, typ.
a
b
a) 100Vac
b) 120Vac
c) 230Vac
50
25
Input Voltage
89
100 120
180
Input Voltage
20
230
264Vac
100 120
180
230
264Vac
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
9
Bulletin 1606 Switched Mode Power Supplies
10. Lifetime Expectancy and MTBF
Lifetime expectancy*)
MTBF**) SN 29500, IEC 61709
MTBF**) MIL HDBK 217F
AC 100V
146 000h*)
413 000h*)
65 000h
184 000h*)
38 000h
107 000h*)
468 000h
770 000h
254 000h
AC 120V
152 000h*)
430 000h*)
70 000h
198 000h*)
43 000h
122 000h*)
484 000h
796 000h
261 000h
AC 230V
168 000h*)
475 000h*)
87 000h
246 000h*)
60 000h
170 000h*)
537 000h
882 000h
290 000h
355 000h
361 000h
395 000h
56 000h
57 000h
64 000h
75 000h
77 000h
86 000h
at 48V, 5A and 40°C
at 48V, 5A and 25°C
at 48V, 10A and 40°C
at 48V, 10A and 25°C
at 48V, 12A and 40°C
at 48V, 12A and 25°C
at 48V, 10A and 40°C
at 48V, 10A and 25°C
at 48V, 10A and 40°C;
Ground Benign GB40
at 48V, 10A and 25°C;
Ground Benign GB25
at 48V, 10A and 40°C;
Ground Fixed GF40
at 48V, 10A and 25°C;
Ground Fixed GF25
*)
The Lifetime expectancy shown in the table indicates the minimum operating hours (service life) and is determined by the lifetime
expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specified in operational hours and is calculated according to the
capacitor’s manufacturer specification. The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years
(131 400h). Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.
**) MTBF stands for Mean Time Between Failure, which is calculated according to statistical device failures, and indicates reliability of a
device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent the life of a product.
The MTBF figure is a statistical representation of the likelihood of a device to fail. A MTBF figure of e.g. 1 000 000h means that
statistically one unit will fail every 100 hours if 10 000 units are installed in the field. However, it cannot be determined if the failed unit
has been running for 50 000h or only for 100h.
11. Functional Diagram
Fig. 11-1 Functional diagram
L
N
Input Fuse
Input Filter
Input Rectifier
Active Inrush Limiter
PFC
Converter
Power
Converter
Output
Filter
Output
Voltage
Regulator
Temperature
Shutdown
10
Output
Power
Manager
Output
OverVoltage
Protection
Output
Voltage
Monitor
+
+
Single /
Parallel
VOUT
DC-ok
LED
DC-ok
Relay
DC-ok
Contact
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
12. Terminals and Wiring
The terminals are IP20 Finger safe constructed and suitable for field- and factory wiring.
Type
Solid wire
Stranded wire
American Wire Gauge
Max. wire diameter
Wire stripping length
Screwdriver
Recommended tightening torque
Input and output
screw terminals
0.5-6mm2
0.5-4mm2
AWG20-10
2.8mm (including ferrules)
7mm / 0.28inch
3.5mm slotted or cross-head No 2
1Nm, 9lb.in
DC-OK-Signal
spring-clamp terminals
0.15-1.5mm2
0.15-1.5mm2
AWG26-14
1.5mm (including ferrules)
7mm / 0.28inch
3.5mm slotted (to open the spring)
not applicable
Instructions:
a) Use appropriate copper cables that are designed for minimum operating temperatures of:
60°C for ambient up to 45°C and
75°C for ambient up to 60°C minimum
90°C for ambient up to 70°C minimum.
b
Follow national installation codes and installation regulations!
c) Ensure that all strands of a stranded wire enter the terminal connection!
d) Do not use the unit without PE connection.
e) Unused terminal compartments should be securely tightened.
f) Ferrules are allowed.
Daisy chaining:
Daisy chaining (jumping from one power supply output to the next) is allowed as long as the average output current
through one terminal pin does not exceed 25A. If the current is higher, use a separate distribution terminal block as
shown in Fig. 12-2.
Fig. 12-1
Daisy chaining of outputs
Power
Supply
+ +
- -
Output
Fig. 12-2
Distribution
Terminals
Power
Supply
+ +
- -
Output
Using distribution terminals
Load
+
-
Power
Supply
+ +
- -
Output
Power
Supply
+ +
- -
Output
Load
+
-
max 25A!
continuous
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
11
Bulletin 1606 Switched Mode Power Supplies
13. Front Side and User Elements
Fig. 13-1 Front side
A
Input Terminals (screw terminals)
N, L
Line input
PE (Protective Earth) input
C
B
Output Terminals (screw terminals, two pins per pole)
+
Positive output
–
Negative (return) output
C
Output voltage potentiometer
Open the flap to adjust the output voltage. Factory set: 48.0V
D
D DC-OK LED (green)
On, when the output voltage is >90% of the adjusted output voltage
F
E
12
E
DC-OK Relay Contact (quick-connect spring-clamp terminals)
The DC-OK relay contact is synchronized with the DC-OK LED.
See section for details.
F
“Parallel Use” “Single Use” selector
Set jumper to “Parallel Use” when power supplies are connected in parallel
to increase the output power. In order to achieve a sharing of the load
current between the individual power supplies, the “parallel use” regulates
the output voltage in such a manner that the voltage at no load is approx.
4% higher than at nominal load. See also section 24.5. A missing jumper is
equal to a “Single Use” mode.
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
14. EMC
The power supply is suitable for applications in industrial environment as well as in residential, commercial and light
industry environment without any restrictions. A detailed EMC report is available upon request.
EMC Immunity
Electrostatic discharge
Electromagnetic RF field
Fast transients (Burst)
Surge voltage on input
Surge voltage on output
Surge voltage on DC-OK
Conducted disturbance
Mains voltage dips
Voltage interruptions
Voltage sags
Powerful transients
According generic standards: EN 61000-6-1 and EN 61000-6-2
EN 61000-4-2
contact discharge
8kV
Criterion A
air discharge
15kV
Criterion A
EN 61000-4-3
80MHz-2.7GHz
20V/m
Criterion A
EN 61000-4-4
input lines
4kV
Criterion A
output lines
2kV
Criterion A
DC-OK signal (coupling clamp)
2kV
Criterion A
EN 61000-4-5
L
N
2kV
Criterion A
L
PE, N
PE
4kV
Criterion A
1kV
Criterion A
EN 61000-4-5
+
PE
2kV
Criterion A
+/EN 61000-4-5
DC-OK signal
PE
1kV
Criterion A
EN 61000-4-6
0.15-80MHz
20V
Criterion A
EN 61000-4-11
0% of 100Vac
0Vac, 20ms
Criterion A
40% of 100Vac
40Vac, 200ms
Criterion C
70% of 100Vac
70Vac, 500ms
Criterion A
0% of 200Vac
0Vac, 20ms
Criterion A
40% of 200Vac
80Vac, 200ms
Criterion A
70% of 200Vac
140Vac, 500ms
Criterion A
EN 61000-4-11
0% of 200Vac (=0V)
5000ms
Criterion C
SEMI F47 0706
dips on the input voltage according to SEMI F47 standard
1000ms
Criterion A
80% of 120Vac (96Vac)
500ms
Criterion A
70% of 120Vac (84Vac)
50% of 120Vac (60Vac)
200ms
Criterion A
VDE 0160
over entire load range
750V, 1.3ms
Criterion A
Criteria:
A: Power supply shows normal operation behavior within the defined limits.
C: Temporary loss of function is possible. Power supply may shut down and restart by itself. The power supply will incur no damage or
hazard.
According generic standards: EN 61000-6-3 and EN 61000-6-4
EMC Emission
Conducted emission
EN 55011, EN 55022, FCC Part 15, CISPR 11, CISPR 22
Class B
input lines
IEC/CISPR 16-1-2, IEC/CISPR 16-2-1
limits for DC power port
Conducted emission
according EN 61000-6-3 fulfilled
output lines**)
Radiated emission
EN 55011, EN 55022
Class B
Harmonic input current
EN 61000-3-2
fulfilled for class A equipment
Voltage fluctuations, flicker EN 61000-3-3
fulfilled*)
This device complies with FCC Part 15 rules.
Operation is subjected to following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
*) tested with constant current loads, non pulsing
**) for information only, not mandatory for EN 61000-6-3
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
13
Bulletin 1606 Switched Mode Power Supplies
The power supply has two converters with two different switching frequencies included.
70kHz to 130kHz
PFC converter, input voltage and output power dependent
80kHz to 140kHz
Main converter, output power dependent
Switching Frequencies
Switching frequency 1
Switching frequency 2
15. Environment
Operational temperature*)
Storage temperature
Output de-rating
-25°C to +70°C (-13°F to 158°F)
-40 to +85°C (-40°F to 185°F)
6.4W/°C
12W/°C
5 to 95% r.h.
2-17.8Hz: ±1.6mm; 17.8-500Hz: 2g***)
2 hours / axis
30g 6ms, 20g 11ms***)
3 bumps / direction, 18 bumps in total
0 to 2000m (0 to 6 560ft)
2000 to 6000m (6 560 to 20 000ft)
Humidity **)
Vibration sinusoidal
Shock
Altitude
reduce output power according Fig. 15-1
for storage and transportation
45°C to 60°C (113°F to 140°F)
60°C to 70°C (140°F to 158°F)
IEC 60068-2-30
IEC 60068-2-6
IEC 60068-2-27
without any restrictions
reduce output power or ambient temperature,
see Fig. 15-2
IEC 62103, EN 50178, overvoltage category II
30W/1000m or 5°C/1000m
> 2000m (6500ft), see Fig. 15-2
III
IEC 62103, EN 50178, altitudes up to 2000m
II
altitudes from 2000m to 6000m
2
IEC 62103, EN 50178, not conductive
The unit does not release any silicone or other LABS-critical substances and is suitable for
use in paint shops.
At load currents below 1A some audible noise will be emitted from the power supply
Altitude de-rating
Over-voltage category
Degree of pollution
LABS compatibility
Audible noise
*) Operational temperature is the same as the ambient temperature and is defined as the air temperature 2cm below the unit.
**) Do not energize in the presence of condensation.
***) Higher levels allowed when using the 1606-XLC wall mounting bracket.
Fig. 15-1 Output current vs. ambient temp.
Allowable Output Current at 48V
Allowed Output Current at 48V
12A
C
A
10A
B
8A
6A
4A
2A
0
-25
Fig. 15-2 Output current vs. altitude
12A
D
10A
C
B
A
8A
6A
A...100 to 264Vac, continuous
B... 85Vac, continuous
C... Short term
0
20
40
A... Tamb < 60°C
B... Tamb < 50°C
C... Tamb < 40°C
D... Short term
4A
2A
60 70°C
0
0
2000m
Ambient Temperature
4000m
6000m
Altitude
See section 3 for derating requirements for input voltages between 85Vac and 100Vac.
14
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
16. Protection Features
Output protection
Output over-voltage protection
Degree of protection
Penetration protection
Over-temperature protection
Input transient protection
Internal input fuse
*)
Electronically protected against overload, no-load and short-circuits*)
typ. 58.5Vdc
In case of an internal power supply defect, a redundant
max. 60Vdc
circuit limits the maximum output voltage. The output
shuts down and automatically attempts to restart.
IP 20
EN/IEC 60529
Caution: For use in a controlled environment according
to CSA 22.2 No 107.1-01.
> 5mm
e.g. screws, small parts
yes
Output shut-down with automatic restart
MOV (Metal Oxide Varistor)
included
not user replaceable
In case of a protection event, audible noise may occur.
17. Safety Features
Input / output separation*)
Class of protection
Isolation resistance
PE resistance
Touch current (leakage current)
*)
SELV
IEC/EN 60950-1
PELV
IEC/EN 60204-1, EN 50178, IEC 62103, IEC 60364-4-41
double or reinforced insulation
I
PE (Protective Earth) connection required
> 5MOhm
input to output, 500Vdc
< 0.1Ohm
typ. 0.14mA / 0.37mA
100Vac, 50Hz, TN-,TT-mains / IT-mains
typ. 0.20mA / 0.55mA
120Vac, 60Hz, TN-,TT-mains / IT-mains
typ. 0.35mA / 0.87mA
230Vac, 50Hz, TN-,TT-mains / IT-mains
max. 0.17mA / 0.46mA
110Vac, 50Hz, TN-,TT-mains / IT-mains
max. 0.26mA / 0.67mA
132Vac, 60Hz, TN-,TT-mains / IT-mains
max. 0.46mA / 1.08mA
264Vac, 50Hz, TN-,TT-mains / IT-mains
double or reinforced insulation
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
15
Bulletin 1606 Switched Mode Power Supplies
18. Dielectric Strength
The output voltage is floating and has no ohmic connection to the ground. Type and factory tests are conducted by
the manufacturer. Field tests may be conducted in the field using the appropriate test equipment which applies the
voltage with a slow ramp (2s up and 2s down). Connect all input-terminals together as well as all output poles before
conducting the test. When testing, set the cut-off current settings to the value in the table below.
Fig. 18-1 Dielectric strength
Type test
Input
DC-ok
*)
B
L
N
60s
B
D
Output
Earth, PE
C
+
-
B
3000Vac
C
1000Vac
D
500Vac
Factory test
5s
2500Vac
2500Vac
500Vac
500Vac
Field test
5s
2000Vac
2000Vac
500Vac
500Vac
> 15mA
> 15mA
> 20mA
> 1mA
Cut-off current setting
A
A
2500Vac
To meet the PELV requirements according to EN60204-1 § 6.4.1, we
recommend that either the + pole, the – pole or any other part of
the output circuit be connected to the protective earth
system. This helps to avoid situations in which a load starts
unexpectedly or cannot be switched off when unnoticed ground
faults occur.
B*) When testing input to DC-OK ensure that the max. voltage between DC-OK and the output is not exceeded (column D). We recommend
connecting DC-OK pins and the output pins together when performing the test.
19. Certifications
EC Declaration of Conformity
The CE Mark indicates conformance with the
- EMC directive 2004/108/EC,
- Low-voltage directive (LVD) 2006/95/EC and
UL 508
Listed E56639 for use in the U.S.A. (UL 508) and Canada
(C22.2 No. 60950)
Industrial Control Equipment
RECOGNIZED E56639 for use in the U.S.A. (UL 60950-1)
and Canada (C22.2 No. 60950-1)
Information Technology Equipment, Level 3
IND. CONT. EQ.
UL 60950-1
CSA C22.2 No.107.1,
ISA 12.12.01
CSA Certified under File Number 240020. CERTIFIED for use
in the U.S.A. (ISA 12.12.01) and Canada (C22.2 No. 213)
Hazardous Location Class I, Div. 2, Groups A, B, C, D
II 3G Ex nA nC II T3 Gc
ATEX
II 3G Ex nA nC II T3 Gc
C-Tick
GOST R
C-tick compliance is for products intended for sale and use within
the Australian market. See below for link to the C-tick Declarations
of Conformity.
GOST R certification is applicable for products for sale and use
within Russia. See below for link to the Certificate.
Product certification information (including Certificates and Declarations of Conformity) can be found at www.ab.com/certification.
16
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
20. Physical Dimensions and Weight
Weight
DIN Rail
Installation Clearances
1000g / 2.2lb
Use 35mm DIN rails according to EN 60715 or EN 50022 with a height of 7.5 or 15mm.
The DIN rail height must be added to the unit depth (127mm) to calculate the total required
installation depth.
See section 2.
Fig. 20-1 Front view
Fig. 20-2 Side view
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
17
Bulletin 1606 Switched Mode Power Supplies
21. Accessories
21.1. 1606-XLC Wall Mounting Bracket
This bracket is used to mount the power
supply onto a flat surface without a DIN rail.
18
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
22. Application Notes
22.1. Peak Current Capability
The power supply can deliver peak currents (up to several milliseconds) which are higher than the specified short term
currents.
This helps to start current demanding loads. Solenoids, contactors and pneumatic modules often have a steady state
coil and a pick-up coil. The inrush current demand of the pick-up coil is several times higher than the steady-state
current and usually exceeds the nominal output current (including PowerBoost). The same situation applies when
starting a capacitive load.
The peak current capability also ensures the safe operation of subsequent circuit breakers of load circuits. The load
branches are often individually protected with circuit breakers or fuses. In case of a short or an overload in one branch
circuit, the fuse or circuit breaker need a certain amount of over-current to open in a timely manner. This avoids
voltage loss in adjacent circuits.
The extra current (peak current) is supplied by the power converter and the built-in large sized output capacitors of
the power supply. The capacitors get discharged during such an event, which causes a voltage dip on the output. The
following two examples show typical voltage dips:
Fig. 22-1 Peak load with 2x the nominal
current for 50ms, typ.
Fig. 22-2 Peak load with 5x the nominal
current for 5ms, typ.
Output
Voltage
48V
Output
Voltage
48V
20A
37V
32V
50A
Output
Current
0A
Output
Current
0A
10ms/DIV
1ms/DIV
Peak load 20A (resistive) for 50ms
Output voltage dips from 48V to 32V.
Peak load 50A (resistive) for 5ms
Output voltage dips from 48V to 37V.
Please note: The DC-OK relay triggers when the voltage dips more than 10% for longer than 1ms.
Peak current voltage dips
typ.
typ.
typ.
from 48V to 32V
from 48V to 39V
from 48V to 37V
at 20A for 50ms, resistive load
at 50A for 2ms, resistive load
at 50A for 5ms, resistive load
22.2. Back-feeding Loads
Loads such as decelerating motors and inductors can feed voltage back to the power supply. This feature is also called
return voltage immunity or resistance against Back- E.M.F. (Electro Magnetic Force).
This power supply is resistant and does not show malfunctioning when a load feeds back voltage to the power supply.
It does not matter whether the power supply is on or off.
The maximum allowed feed-back-voltage is 63Vdc. The absorbing energy can be calculated according to the built-in
large sized output capacitor which is specified in section 6.
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
19
Bulletin 1606 Switched Mode Power Supplies
22.3. External Input Protection
The unit is tested and approved for branch circuits up to 30A (UL) and 32A (IEC). An external protection is only
required if the supplying branch has an ampacity greater than this. Check also local codes and local requirements. In
some countries local regulations might apply.
If an external fuse is necessary or utilized, minimum requirements need to be considered to avoid nuisance tripping of
the circuit breaker. A minimum value of 10A B- or C-Characteristic breaker should be used.
22.4. Output Circuit Breakers
Standard miniature circuit breakers (MCBs or UL1077 circuit breakers) are commonly used for AC supply systems and
may also be used on 48V branches.
MCBs are designed to protect wires and circuits. If the ampere value and the characteristics of the MCB are adapted to
the wire size that is used, the wiring is considered as thermally safe wether the MCB opens or not.
To avoid voltage dips and under-voltage situations in adjacent 48V branches which are supplied by the same source, a
fast (magnetic) tripping of the MCB is desired. A quick shutdown within 10ms is necessary corresponding roughly to
the ride-through time of PLCs. This requires power supplies with high current reserves and large output capacitors.
Furthermore, the impedance of the faulty branch must be sufficiently small in order for the current to actually flow.
The best current reserve in the power supply does not help if Ohm’s law does not permit current flow. The following
table has typical test results showing which B- and C-Characteristic MCBs magnetically trip depending on the wire cross
section and wire length.
Fig. 22-3 Test circuit
Power Supply
AC
MCB
+
+
Wire length
S1... Fault simulation switch
20
S1
-
DC -
*)
Load
Maximal wire length*) for a fast (magnetic) tripping:
0.75mm²
1.0mm²
1.5mm²
2.5mm²
C-2A
74m
98m
134m
198m
C-3A
57m
74m
106m
168m
C-4A
43m
56m
73m
114m
C-6A
11m
16m
23m
33m
C-8A
1m
1m
2m
3m
B-6A
19m
36m
51m
82m
B-10A
9m
12m
18m
27m
B-13A
7m
10m
16m
24m
Don’t forget to consider twice the distance to the load (or cable length) when calculating the total wire length (+ and – wire).
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
22.5. Parallel Use to Increase Output Power
1606-XLE480FP power supplies can be paralleled to increase the output power.
The output voltage of all power supplies shall be adjusted to the same value
(±100mV) in “Single use” mode with the same load conditions on all units, or
the units can be left with the factory settings. After the adjustments, the
jumper on the front of the unit shall be moved from “Single use” to “Parallel
use”, in order to achieve load sharing. The “Parallel use” mode regulates the
output voltage in such a manner that the voltage at no load is approx. 4%
higher than at nominal load. See also section 6. If no jumper is plugged in, the
unit is in “Single use” mode. Factory setting is “Single use” mode.
Unit A
AC
DC
+
+
Unit B
AC
DC
Load
+
-
-
If more than three units are connected in parallel, a fuse or circuit breaker
with a rating of 15A or 16A is required on each output. Alternatively, a diode or redundancy module can also be
used.
Energize all units at the same time to avoid the overload HiccupPLUS mode. It also might be necessary to cycle the input
power (turn-off for at least five seconds), if the output was in HiccupPLUS mode due to overload or short circuits and the
required output current is higher than the current of one unit.
Keep an installation clearance of 15mm (left / right) between two power supplies and avoid installing the power
supplies on top of each other. Do not use power supplies in parallel in mounting orientations other than the standard
mounting orientation (terminals on bottom of the unit) or in any other condition where a derating of the output
current is required (e.g. altitude, above 60°C, …).
Pay attention that leakage current, EMI, inrush current, harmonics will increase when using multiple power supplies.
22.6. Parallel Use for Redundancy
Power supplies can be paralleled for redundancy to gain higher system availability. Redundant systems require a
certain amount of extra power to support the load in case one power supply unit fails. The simplest way is to put two
power supplies in parallel. This is called a 1+1 redundancy. In case one power supply unit fails, the other one is
automatically able to support the load current without any interruption. Redundant systems for a higher power
demand are usually built in a N+1 method. E.g. five power supplies, each rated for 10A are paralleled to build a 40A
redundant system. For N+1 redundancy the same restrictions apply as for increasing the output power, see also section
22.5.
Recommendations for building redundant power systems:
a)
b)
c)
d)
Use separate input fuses for each power supply.
Set the power supply into “Parallel use” mode.
Monitor the individual power supply units. Therefore, use the DC-OK relay contact of the power supply.
It is desirable to set the output voltages of all units to the same value (± 100mV) or leave it at the factory setting.
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
21
Bulletin 1606 Switched Mode Power Supplies
22.7. Series Operation
Power supplies of the same type can be connected in series for higher
output voltages. It is possible to connect as many units in series as needed,
providing the sum of the output voltage does not exceed 150Vdc. Voltages
with a potential above 60Vdc are not SELV any more and can be dangerous.
Such voltages must be installed with a protection against touching.
Earthing of the output is required when the sum of the output voltage is
above 60Vdc.
Unit A
AC
DC
+
+
Unit B
AC
DC
Avoid return voltage (e.g. from a decelerating motor or battery) which is
applied to the output terminals.
Load
+
-
Earth
(see notes)
Keep an installation clearance of 15mm (left / right) between two power supplies and avoid installing the power
supplies on top of each other. Do not use power supplies in series in mounting orientations other than the standard
mounting orientation (terminals on bottom of the unit).
Pay attention that leakage current, EMI, inrush current, harmonics will increase when using multiple power supplies.
22.8. Inductive and Capacitive Loads
The unit is designed to supply any kind of loads, including capacitive and inductive loads. If extreme large capacitors,
such as EDLCs (electric double layer capacitors or “UltraCaps”) with a capacitance > 0.15F are connected to the output,
the unit might charge the capacitor in the HiccupPLUS mode (see section 6).
22
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Bulletin 1606 Switched Mode Power Supplies
22.9. Charging Batteries
The power supply can be used to charge lead-acid or maintenance free batteries. (Four 12V batteries in series)
Instructions for charging batteries:
a)
b)
Set output voltage (measured at no load and at the battery end of the cable) very precisely to the end-of-charge
voltage.
End-of-charge voltage
55.6V
55.0V
54.3V
53.6V
Battery temperature
10°C
20°C
30°C
40°C
Use a 15A or 16A circuit breaker (or blocking diode) between the power supply and the battery.
c)
Ensure that the output current of the power supply is below the allowed charging current of the battery.
d)
Use only matched batteries when putting 12V types in series.
e)
The return current to the power supply (battery discharge current) is typ. 7mA when the power supply is switched
off (except if using a blocking diode).
22.10. Operation on Two Phases
Power Supply
The power supply can also be used on two phases of a three-phase-system.
Such a phase-to-phase connection is allowed as long as the supplying
voltage is below 240V+10%.
240V +10% max.
L1
L3
L2
AC
L
internal
fuse
N
PE
DC
22.11. Use in a Tightly Sealed Enclosure
When the power supply is installed in a tightly sealed enclosure, the temperature inside the enclosure will be higher
than outside. In such situations, the inside temperature defines the ambient temperature for the power supply.
The following measurement results can be used as a reference to estimate the temperature rise inside the enclosure.
The power supply is placed in the middle of the box, no other heat producing items are inside the box
Enclosure:
Load:
Input:
Temperature inside enclosure:
Temperature outside enclosure:
Temperature rise:
Rittal Typ IP66 Box PK 9522 100, plastic, 254x180x165mm
48V, 8A; (=80%) load is placed outside the box
230Vac
53.3°C (in the middle of the right side of the power supply with a distance of 2cm)
25.3°C
28.0K
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
23
Bulletin 1606 Switched Mode Power Supplies
22.12. Mounting Orientations
Mounting orientations other than all terminals on the bottom require a reduction in continuous output power or a
limitation in the maximum allowed ambient temperature. The amount of reduction influences the lifetime expectancy
of the power supply. Therefore, two different derating curves for continuous operation can be found below:
Curve A1
Curve A2
Recommended output current.
Max allowed output current (results in approximately half the lifetime expectancy of A1).
Fig. 22-4
Mounting
Orientation A
(Standard
orientation)
Output Current
12A
A1
9
Power
Supply
6
3
Ambient Temperature
0
INPUT OUTPUT
10
Fig. 22-5
Mounting
Orientation B
(Upside down)
20
30
40
12A
INPUT OUTPUT
9
A2
A1
Power
Supply
6
Ambient Temperature
0
10
Fig. 22-6
Mounting
Orientation C
(Table-top
mounting)
20
30
40
60°C
12A
9
6
A2
A1
Ambient Temperature
0
10
20
30
40
50
60°C
Output Current
12A
Power
Supply
INPUT OUTPUT
9
6
A2
A1
3
Ambient Temperature
0
10
20
30
40
50
60°C
Output Current
INPUT OUTPUT
Power
Supply
12A
9
6
A2
A1
3
Ambient Temperature
0
10
24
50
Output Current
3
Fig. 22-8
Mounting
Orientation E
(Horizontal ccw)
60°C
Output Current
3
Fig. 22-7
Mounting
Orientation D
(Horizontal cw)
50
20
30
40
50
60°C
All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.
Rockwell Automation Publication 1606-RM043A-EN-P — March 2014
Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its products.
At http://www.rockwellautomation.com/support, you can find technical manuals, technical and application
notes, sample code and links to software service packs, and a MySupport feature that you can customize to
make the best use of these tools. You can also visit our Knowledgebase at http://
www.rockwellautomation.com/knowledgebase for FAQs, technical information, support chat and forums,
software updates, and to sign up for product notification updates.
For an additional level of technical phone support for installation, configuration, and troubleshooting, we offer
TechConnectSM support programs. For more information, contact your local distributor or Rockwell Automation
representative, or visit http://www.rockwellautomation.com/support/.
Installation Assistance
If you experience a problem within the first 24 hours of installation, review the information that is contained in
this manual. You can contact Customer Support for initial help in getting your product up and running.
United States or Canada
1.440.646.3434
Outside United States or Canada
Use the Worldwide Locator at http://www.rockwellautomation.com/rockwellautomation/support/overview.page, or contact your local
Rockwell Automation representative.
New Product Satisfaction Return
Rockwell Automation tests all of its products to help ensure that they are fully operational when shipped from
the manufacturing facility. However, if your product is not functioning and needs to be returned, follow these
procedures.
United States
Contact your distributor. You must provide a Customer Support case number (call the phone number above to obtain one) to your
distributor to complete the return process.
Outside United States
Please contact your local Rockwell Automation representative for the return procedure.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to
improve this document, complete this form, publication RA-DU002, available at http://
literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.
Publication 1606-RM043A-EN-P — March 2014
Copyright © 2014 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
">